1 Introduction

3 Button Functions
Operating Manual For Easy Clicker

UR3-SR

This remote control is designed to operate most digital and analog cable boxes, as well as TVs, and a VCR or DVD player.
*Note : Try all the functions on the remote control. If any of the functions do not operate as they should, repeat the instructions from Step 2 using the next three-digit code number from the same brand list.
D. Programming a Second TV to the VCR Button
STEP1 Press the [VCR] button and the [SELECT/OK] button simultaneously for 3 seconds. The VCR LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP2 Press the [TV] button. STEP3 Point the remote control toward the TV and enter the three-digit code for your TV from the TV codes table. STEP4 Store the three-digit code by pressing the [VCR] button. The device LED will blink twice to confirm that the code has been stored.

B. Auto Search Method

2 Installing Batteries
Before you program or operate the remote control, you must install two new AAA alkaline batteries. STEP1 Remove the battery compartment cover from the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below. STEP3 Replace the battery compartment cover.
Install two AAA alkaline batteries as shown here
If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps: STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV, VCR, or DVD). STEP2 Press the [DEVICE] button and the [SELECT/OK] button simultaneously for three seconds. The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 20 seconds. The next step must be entered while the LED is on. STEP3 Point the remote control toward the equipment and alternately press the [CH+] (or [CH-]) button and the [MUTE] button. If the right code number is sent, the equipment will turn off. *Note : You can verify that you selected the correct code by pressing the [MUTE] button again. The equipment should turn On or Off. STEP4 Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored.
STEP2 Press a [MACRO] button and the [SELECT/OK] button simultaneously for 3 seconds. The CBL device LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP3 Press the [CH+] button to erase the functions stored in the button. The CBL device LED will blink twice to confirm that the memory button has been erased.
F. Assigning the Volume and Mute keys to a Different Device
By default, the volume and mute keys operate volume and mute functions on the TV. If you would like those keys to operate those functions on a different device, follow these steps. STEP1 Press the [SELECT/OK] button and [CBL] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP2 Press the [VOL +] button. The device LED will blink. STEP3 Press the [DEVICE] button corresponding to the device that you would like the volume and mute buttons to control. The device LED will blink twice to confirm the programming. Example : If you wish to have the volume and mute keys operate your cable box, press the [CBL] button in Step3.
E. Programming for Advanced Functions.
In the CABLE device mode, the A,B,C and blank macro buttons can be programmed to act as macro buttons to send out up to 10 commands with one button press. In this section, when youre instructed to press a [MACRO] button, you need to press either the A, B, C or blank macro button (depending on which button you are attempting to program). *Note : The A, B, and C buttons are not programmable if you have a digital cable box made by Pace, Pioneer, or Scientific-Atlanta cable box. STEP1 Press the [CBL] button to select the CABLE mode. STEP2 Press a [MACRO] button and the [SELECT/OK] button simultaneously for 3 seconds. The CBL device LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP3 Press up to 10 buttons you wish to store. The CBL device LED will blink once for each command entered. STEP4 Press the [CH+] button to store the functions that are selected. The CBL device LED will blink twice to confirm the storage of functions. To erase the Macro programming and return to the original function: STEP1 Press the [CBL] button to select the CABLE mode.

G. Assigning the Channel keys to a Different Device
By default, the CH UP, CH Down, Numeric buttons, and LAST keys operate through your Cable Box. If you would like those keys to operate those functions on a different device, follow these steps. STEP1 Press the [SELECT/OK] button and [CBL] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP2 Press the [VOL -] button. The device LED will blink. STEP3 Press the [TV] button. The device LED will blink twice to confirm the programming. *Note : If you wish to have the channel keys operate your Cable box, press the [CBL] button instead of the [TV] button in Step 3.
4 Programming the Remote Control.
*Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either the CBL, TV, or VCR button, depending on which device you are programming the remote to operate. STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV, VCR, or DVD). STEP2 Press the [DEVICE] button and the [SELECT/OK] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 20 seconds. The next step must be entered while the LED is on. STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off. *Note : You can verify that you have selected the correct code by pressing the [MUTE] button. The equipment should turn on or off. STEP4 Store the three-digit code by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored.
C. To find the Three-Digit Code that Was Programmed using the Auto Search Method
STEP1 Press the appropriate [DEVICE] button and the [SELECT/OK] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP2 Press the [INFO] button. The device LED will blink a number of times indicating the number of each digit for the code. Each digit is separated by a one second interval of the LED being off. Example : One blink, then three blinks, then eight blinks indicates the code number 138. *Note : Ten blinks indicates the number 0.

A. Manual Programming

Universal Remote Control, Inc.

www.universalremote.com

OCE-0009A Rev 05 (08/05/04)
The remote control can be programmed by entering a three-digit code number that corresponds to particular brands and models of equipment. The three-digit code numbers are listed in the code tables sections of this instruction manual.

H. Low Battery Warning

When the battery is low (2.3V-2.0V) and needs to be replaced with fresh batteries, device LED will blink 2 times in sequence whenever a [DEVICE] button is pressed to turn on equipment.

MAKER(BRAND) NAME

AMPRO ANAM AOC APEX DIGITAL AUDIOVOX BAYSONIC BELL&HOWELL BRADFORD BROKSONIC CAIRN CANDLE CAPEHART CARVER CELEBRITY CETRONIC CINERAL CITIZEN CLASSIC CONCERTO CONTEC CORONADO CRAIG CROSLEY CROWN CURTIS MATHES CXC DAEWOO DAYTRON DENON DUMONT DWIN DYNASTY DYNATECH ELECTROBAND ELECTROHOME EMERSON ENVISION FISHER FUJITSU FUNAI FUTURETECH GATEWAY GE GIBRALTER GOLDSTAR GRUNPY HALL MARK HARLEY DAVIDSON HARMAN KARDON HARVARD HITACHI INFINITY INKEL INTEQ JBL JCB JCPENNEY JENSEN JVC KENWOOD KLOSS
CODE NUMBER (3 DIGIT) LIST

002 059

CODE NUMBER (3 DIGIT) LIST MAKER(BRAND) NAME
SOLE SONY SOUNDESIGN SPECTRICON SQUAREVIEW SSS STARLITE SUPRE MACY SUPREME SYLVANIA

VCR & TV/VCR

DAEWOO DAYTRON DIMENSIA DBX DYNATECH ELECTROHOME ELECTROPHONIC EMERSON FISHER FUJI FUNAI GARRARD GE GO VIDEO GOLDSTAR / LG HARLEY DAVIDSON HARMAN KARDON HARWOOD HITACHI HUGHES HQ INSTANTREPLAY JCL JCPENNEY JENSEN JVC KEC KENWOOD KLH KODAK LLOYD LOGIK LXI MAGIN MAGNASONIC MAGNAVOX MARANTZ MARTA MATSUI MATSUSHITA MEI MEMOREX MGA MGN TECHNOLOGY MINOLTA MITSUBISHI MOTOROLA MTC MULTITECH NEC NIKKO NOBLEX NORDMENDE OLYMPUS OPTIMUS OPTONICA ORION PANASONIC PENTAX PHILCO PHILIPS PILOT
PIONEER PORTLAND PROFITRONIC PROTEC QUARTZ QUASAR RADIO SHACK RADIX RANDEX RCA REALISTIC RICO SALORA SAMSUNG SANKY SANSUI SANYO SCOTT SEARS SHARP SHINTOM SHOGUN SIGNATURE SINGER SONY SOUNDESIGN STS SYLVANIA SYMPHONIC TANDY TATUNG TEAC TECHNICS TEKNIKA THOMAS TMK TOSHIBA TOTEVISION UNITECH VECTOR RESEARCH VIDEO CONCEPTS VIDEOSONIC WARDS WESTING HOUSE XR-1000 YAMAHA ZENITH
KTV LG LODGENET LOEWE LOGIK LUXMAN LXI MAGNAVOX

I. Memory Lock System.

This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

5 Set-up Code Tables

CABLE TV
MAKER(BRAND) NAME CONVERTER CODE No
034 MOTOROLA DCT Series GENERAL INSTRUMENT CFT2200 JERROLD CFT2000 DRZ DL4, DP(V), DQN(V), DPBB DRX Some Model HAMLIN CR6000 CR6600, 6800,C R83 CRX5000 NSC IM781R IM781 OAK SIGMAONE, P1,P2,P3, SIGMA 2000 RTC56,RKDM SIGMA 2001,2002 SIGMA 450,500,550 PACE 510 PANASONIC 140,145,170,175 110,120,130,150,160 PIONEER VOYAGER Series BA9000 BA4100,4200,4500 BA-V1000 REGENCY ALL MODELS SCIENTIFIC ATLANTA EXPLORER Series 8600X 8600 8540,8570,SONY DHG-M55CV TOCOM 5507 5503A ZENITH MN2500 PM Z-TAC

ADMIRAL ADVENT AIWA AKAI AKIO ALARON AMARK AMERICA ACTION
MAJESTIC 072 MARANTZ MATSUI 164 MATSUSHITA 080 MEGATRON 004 MEMOREX 096 METZ 088 MGA MIDLAND 073 MINERVA 088 MINUTZ 008 MITSUBISHI MOTOROLA 081 MTC MULTITECH 043 NAD NEC NIKEI 043 NIKKO 103 NTC 103 ONKING 043 ONWA 043 OPTIMUS 080 OPTONICA ORION 028 PANASONIC PHILCO PHILIPS PIONEER 191 PORTLAND 103 PRISM 034 PROSCAN PROTON QUASAR RADIO SHACK 043 RCA 081 REALISTIC RUNCO SAMPO SAMSUNG SANSEI 120 SANSUI 096 SANYO SCOTCH 004 SCOTT SEARS SELECO 189 SEMIVOX 043 SEMP 015 SHARP 143 SIGNATURE 072
SYMPHONIC TANDY 081 TATUNG 209 TECHNICS TECHNOL ACE 028 TECHWOOD 004 TEKNIKA TELERENT 072 TERA 172 THOMPSON 166 TNCI 073 TMK 004 TOSHIBA TOTEVISION 143 UNIVERSAL VIDEO CONCEPTS 146 VIDIKRON 164 VIDTECH 004 WESTING HOUSE 076 WARDS YAMAHA YORK 004 YUPITERU 043 ZENITH ZONDA 112
ADMIRAL AIKO AIWA AKAI AMERICA ACTION AMERICAN HIGH AMPRO ANAM ASHA AUDIO DYNAMICS AUDIOVOX BEAUMARK BROKSONIC CALIX CANON CAPEHART CCE CINERAL CITIZEN COLT CRAIG CURTIS MATHES CYBERNEX

154 040

STEP3 Press the [VCR] button. The CBL device LED will blink twice to confirm the programming. DVD & TV/DVD(VCR)
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST
*Note : For TV/VCR & TV/DVD combination units, Please use following steps to operate the volume control.
STEP1 Press the [CBL] button and the [SELECT/OK] button simultaneously for 3 seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on. STEP2 Press the [VOL+] button.
ADCOM AIWA ALPINE APEX DIGITAL ARCAM BOSE CLASSE CYBERHOME DAEWOO DENON FUNAI GE GOLDSTAR / LG GO VIDEO GRADIENTE HARMAN KARDON HITACHI HITEKER INTEGRA JVC KENWOOD KLH KOSS KRELL LEXICON MAGNAVOX MARANTZ MCINTOSH MEMOREX MERIDIAN MINTEK MITSUBISHI MYRYAD NAD ONKYO OPTIMUS ORITRON PANASONIC PHILIPS PIONEER PROCEED PROSCAN RCA SANSUI SANYO SAMSUNG SHARP SONY SYLVANIA SYMPHONIC TAG McLaren TECHNICS THETA DIGITAL TOSHIBA VENTURER VINK YAMAHA ZENITH

182 194

Your Programming Codes Set-Top Box ___002___ TV _______________ DVD _______________ VCR _______________ Other ______________
Waitsfield Cable Remote Control FAQs

(Model # UR5U-8720L-WFC)

How Do I Program My Remote to Turn on/off my TV and DVR? Your universal remote control comes preprogrammed to work with your Motorola set-top box. You can also program it to operate your TV, VCR, DVD player, and other Audio equipment if you choose. *
Step 1. Refer to the instruction manual included with your remote or visit our website to find the codes for the manufacturer of the equipment you would like to program. We recommend that you start with your TV. Step 2. Turn on your TV or other equipment that you want to program. Step 3. Press the TV button and the OK/SEL button simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds indicating the remote is ready to be programmed. Step 4. Point the remote toward your TV and enter the 3-digit code. If the 3-digit code you entered is correct, your TV or other equipment you are programming will turn off. If it did not turn off, continue entering the next code numbers until the component you are programming turns off. Step 5. After you've entered the correct code and the component you are programming has turned off, press the POWER button to turn the component back on. Now it is time to test the VOLUME and MUTE buttons for the TV to make sure they all work. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand until you find the one that works. Step 6. Once you have found the correct 3-digit code, save it by pressing the same COMPONENT button one more time. The Component LED light will blink twice to confirm the code was successfully stored. Step 7. Repeat the process for each piece of equipment you want to program. Note: Once youve programmed the remote control to work with a TV in one of your rooms, be sure to label it accordingly (i.e., Living Room TV). If the remote control gets moved to a different brand/model TV in another location in your home, it will not work properly. *All brands and models may not be supported.
My remote sometimes stops working on my set-top box or TV. Your remote is pre-programmed to work with your set-top box. However, if it stops working, simply follow these instructions to re-program.
Try pressing the Component button (CBL or TV, depending on what component you are trying to talk to) first, then press the button for what you are trying to do (volume, channel, etc.). One of the other Component buttons may have accidentally been pressed; when this happens, your remote is trying to send commands to that component. Continued on back.
Waitsfield Cable P.O. Box 9, Waitsfield, VT www.waitsfieldcable.com 496-5800
Make sure you are within range (about 12-15 feet) and pointing the remote at the component. Try fresh batteries. Your remote uses two AA alkaline batteries. If it still isnt working, use the following steps to reprogram your remote.
My remote lost its memory or gets deprogrammed altogether On your remote control, press and hold the CBL and OK/SEL button for three seconds, until the CBL button lights, then release the buttons. On the keypad, press 2, then the CBL button, which will blink twice to show that it has accepted the code. The set-top box should turn off or on. (This procedure must be done within 20 seconds, or the remote will exit the programming mode.) The remote is now reprogrammed to your cable set-top box. (This also works on the UR3-SR big-button remote).
I still cant get my remote to work my set-top box
Try a factory reset: Press and hold the CBL and REC buttons for five seconds, until the Component buttons flash three times in sequence. Release the buttons, and the remote should now control the set-top box. (Note: this will erase any codes that you have stored in the remote to control your other components, such as TV, DVD, etc.)
How can I program the WC remote so that if I mistakenly press TV and then the Channel Up/Down button, it doesnt switch the TV to a different input?
Once you program the WC remote to control your TV set, you can eliminate this problem by pressing and holding the TV and OK/SEL button for three seconds until the TV button lights. Release the buttons. Next, (within 30 seconds) press the Volume down button, and then the CBL button. The TV button will blink twice to confirm.
Whenever I press a button, the AUX, DVD, VCR, TV and CBL buttons flash twice
This is a low-battery indicator. Replace with two AA alkaline batteries. The remotes have a non-volatile memory; codes programmed into them will last for ten+ years, even if the batteries go dead or are removed. TIP: If you use your remote to control TV, DVD or VCR functions and have more than one set, label each remote so they dont get mixed up!

Visit our website at www.waitsfieldcable.com for more tips and online tutorials on using your remote and Interactive Program Guide.