Operating Instructions For 4 in 1 Cable Remote Control

UR4-EXP

1 Introduction
The remote control is designed to operate the Scientific-Atlanta Explorer series and The Pioneer Voyager set top boxes. You can also control the majority of TV, VCR/DVD and AUDIO equipment on the market as shown below. CABLE : Cable Converters TV : Televisions VCR : VCRs and DVD AUX : Audio Receivers, DMX, DCR, TIVO, etc.

3 Button Functions

*Tip : The equipment will turn off when the correct three-digit code number has been entered. You can verify you have selected the correct code by pressing the [POWER] button, the equipment should turn on or turn off. *Note : If there is more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off. STEP4 Store the three-digit code number by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored. *Note : Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 2 using the next three-digit code number from the same brand list.
C. To Find the Three Digit CodeNumber That was Stored in the Device.
STEP1 Press the [DEVICE] button (TV, VCR or AUX) you wish to verify and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [INFO] button. The device LED will blink number of times indicating the number of each digit of the code number. Each digit is separated by a 1 second interval of the LED being turned off. Example : One blink, three blinks and eight blinks with an interval of 1 second of LED being turned off, indicates the code number 138. *Note : Ten blinks is equal to the number 0.
STEP3 Press the [DEVICE] button and the [POWER] button you wish to store in the System On/Off button and repeat this until you stored all the power commands into the System On/Off button. STEP4 Press the [CH+] button to save the power commands you stored. The [CBL] button will blink twice to confirm the saving.
STEP1 Press the [CBL] button and the [SELECT] button simultaneously for 3 seconds. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [VOL +] button. STEP3 Press the [CBL] button. The device LED will blink twice to confirm the programming. To return to original state: If you wish to restore the TV volume control in CBL mode, repeat the above steps by pressing [TV] in STEP3.

2 Replacing Batteries

Before you program or operate the remote control, you must install two new AA alkaline batteries. STEP1 Remove the battery compartment cover on the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown In the illustration below. STEP3 Replace the battery compartment cover.
F. Programming Channel Control.
By following the steps below, the user can program the channel controls (Channel Up, Channel Down and Last) from one device to operate in another device mode. The default channel control settings on the remote control is as follows: CBL : CBL T V : CBL VCR : VCR AUX : AUX If you wish to store the TV channel control in TV mode, use the following steps. STEP1 Press the [TV] button and the [SELECT] button simultaneously for 3 seconds. *Tip : The device LED will light on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [VOL -] button. STEP3 Press the [TV] button. The device LED will blink twice to confirm the programming. To return to original state: If you wish to restore the CABLE channel control in TV mode, repeat the above steps by pressing [CBL] in STEP3.

H. Programming For Advanced Function.
In the CBL mode, the A, B and C buttons can be programmed to act as a macro or favorite channel button to send out up to 10 commands with one button press. STEP1 Press the [CBL] button to select the CBL mode. STEP2 Press the [A, B, or C] button and [SELECT] button simultaneously for 3 seconds. The [CBL] device LED will turn on for 20 seconds. STEP3 Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered. STEP4 Press the [CH+] button to store the functions that were selected. The [CBL] device LED will blink twice to confirm the storage of functions.

B. Auto Search Method.

If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps: STEP1 Turn on the equipment you wish to operate. STEP2 Press the [DEVICE] button (TV, VCR or AUX) to be programmed and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on.
D. Programming a second TV to AUX Mode.
STEP1 Press the [AUX] button to be programmed and the [SELECT] button simultaneously for 3 seconds.The [AUX] device LED will turn on. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [TV] device button to pick up the TV code table. STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. STEP4 Store the three-digit code number by pressing the [AUX] button once again. The device LED will blink twice to confirm that the code has been stored.

4 Operations

Default State: Device Default: CABLE Channel Default: CABLE channel and number keys through the CABLE, with the option of controlling channel and number keys through the TV or VCR. Refer to section F for programming the channel and number keys through your TV or VCR. Volume Default: CABLE volume and mute through the TV, with the option of controlling volume and mute through the Cable box or Audio. Refer to section G for programming the volume and mute through your Cable box or Audio. System On/Off button: This button is designed to send out power commands for two, three or all four devices with one button press. Please refer to section E for details.

I. Low Battery Warning.

When the batteries are low and need to be replaced with fresh batteries, the remote control LED will blink 2 times in sequence whenever a [POWER] button is pressed to turn on equipment.
5 Programming the Remote Control
A. Three-Digit Code Programming Method.
The remote control can be programmed by pressing in a three-digit code number that corresponds to particular manufacturers and brands of Audio/Video equipment. The three-digit code numbers are listed in the code table of the instruction manual. STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUX) STEP2 Press the [DEVICE] button (TV, VCR or AUX) to be programmed and [SELECT] button simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready to be programmed. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables.
*Tip : The device LED will turn on for 20 seconds. The next step must be entered while LED is on. STEP3 Press the [CH+] or [CH-] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH+] or [CH-] button as soon as the equipment turns off. *Tip : You can verify that you selected the correct code by pressing the [POWER] button. The equipment should either turn on or off. STEP4 Press the same [DEVICE] button to store the code. The device LED will blink twice to confirm that the code has been stored.
G. Programming Volume Control.
By following the steps below, the user can program the volume controls (Volume Up, Volume Down and Mute) from one device to operate in another device mode. The default volume control settings on the remote control is as follows: CBL : TV VCR : TV T V : TV AUX : AUX

J. Memory Lock System.

This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
E. Programming the System On/Off Button.
This is designed to program the System On/Off button so that it can send out up to four power on/off commands with one button press. STEP1 Press the [CBL] button. STEP2 Press the [SYSTEM] button and the [SELECT] button simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds.

K. Write your device Set-up codes.
TV VCR AUX Set-up Code Number: Set-up Code Number: Set-up Code Number:
Universal Remote Control, Inc.

www.universalremote.com

OCE-0005A Rev 08 (02/06/07)
If you wish to store the CBL volume control in CBL mode, use the following steps. The [CBL] device LED will turn on.

6 Set-up Code Tables

CABLE TV

Remote

MAKER(BRAND) NAME
CODE NUMBER (3 DIGIT) LIST MAKER(BRAND) NAME

QUASAR RADIO SHACK RCA

VCR & TV/VCR
ADMIRAL AIKO AIWA AKAI AMERICA ACTION AMERICAN HIGH AMPRO ANAM ASHA AUDIO DYNAMICS AUDIOVOX BEAUMARK BROKSONIC CALIX CANON CAPEHART CCE CINERAL CITIZEN COLT CRAIG CUIRTIS MATHES CYBERNEX DAEWOO DAYTRON DBX DYNATECH ELECTROHOME ELECTROPHONIC EMERSON
MAGNAVOX MARANTZ MARTA MATSUI MATSUSHITA MEI MEMOREX MGA MGN TECHNOLOGY MINOLTA MITSUBISHI MOTOROLA MTC MULTITECH NEC NIKKO NOBLEX NORDMENDE OLYMPUS OPTIMUS PILOT PIONEER PORTLAND PROFITRONIC PROTEC RCA

YAMAHA ZENITH

VCR(DVD)
CODE NUMBER (3 DIGIT) LIST

048 025

AUX(AUDIO)
POLAROID PRIMARE PROCEED PROSCAN RCA SAMSUNG SANSUI SANYO SENSORY SCIENCE SHARP SONY SYLVANIA SYMPHONIC TATUNG TECHNICS THETA DIGITAL TOSHIBA VENTURER YAMAHA ZENITH
KENWOOD KOSS KRELL KYOCERA LEXICON LG LUXMAN LXI MAGNAVOX MARANTZ MCINTOSH MCS MERIDIAN MITSUBISHI MONDIAL NAD NAKAMICHI NEC ONKYO OPTIMUS PANASONIC PARASOUND PHILIPS PIONEER PROCEED QUASAR RCA REALISTIC ROTEL SAMSUNG SANSUI SANYO SCOTT SEARS SHARP SHERWOOD SIRIUS SONY SOUNDESIGN SSI TEAC TECHNICS THETA DIGITAL TOSHIBA YAMAHA ZENITH

Converter

Scientific-Atlanta Explorer series, Pioneer Voyager, Pace 510 and 550

Code No

ADMIRAL ADVENT AIKO AKAI ALARON AMARK AMERICA ACTION AMPRO ANAM AOC APEX DIGITAL AUDIOVOX BAYSONIC BELL&HOWELL BRADFORD BROKSONIC CANDLE CAPEHART CARVER CELEBRITY CETRONIC CINERAL CITIZEN CLASSIC CONCERTO CONTEC CORONADO CRAIG CROSLEY CROWN CURTIS MATHES CXC DAEWOO DAYTRON DELL DENON DUMONT DWIN DYNASTY DYNATECH ELECTROBAND ELECTROHOME EMERSON ESA FISHER FUJITSU FUNAI FUTURETECH GATEWAY

242 078

120 GEM 128 GIBRALTER GOLDSTAR GRUNPY HALL MARK 004 HARLEY DAVIDSON 028 HARMAN KARDON 164 HARVARD 043 HISENSE 170 HITACHI 166 HP HYUNDAI INFINITY 164 INSIGNIA INKEL 129 INTEQ 073 JBL 164 JCB 001 JCPENNEY JENSEN 013 JVC KENWOOD KLOSS KTV LG 084 LODGENET 072 LOEWE LOGIK 072 LUXMAN 004 LXI MAGNAVOX MAJESTIC 072 MARANTZ MATSUI 164 MATSUSHITA 080 MEGATRON 004 MINTEK MITSUBISHI 225 MOTOROLA 081 MTC MULTITECH 043 NAD OPTIMUS 080 OPTOMA PHILCO PHILIPS PIONEER POLAROID PORTLAND 103 PRISM 034 PROSCAN 161 PROTON PROTRON 130 141
REALISTIC RUNCO 169 SAMPO SAMSUNG 229 SANSEI 120 SANSUI 096 SANYO 020 SCEPTRE 036 SCOTCH 004 SCOTT SEARS SEMIVOX 043 SEMP 015 SHARP SIGNATURE 072 SONY 139 SOUNDESIGN SPECTRICON 112 SQUAREVIEW 052 SSS STARLITE 043 SUPRE MACY 002 SUPREME 001 SVA 079 SYLVANIA 249 SYMPHONIC SYNAX OLEVIA 084 SYNTAX OLEVIA 132 TANDY 081 TATUNG TECHNICS TECHNOL ACE 028 TECHWOOD 004 TEKNIKA 164 TELERENT 072 TERA 172 TMK 004 TNCI 073 TOSHIBA 045 TOTEVISION 143 UNIVERSAL VIDEO CONCEPTS 146 VIDIKRON VIDTECH 004 VIEWSONIC 122 VIZIO 121 WARDS 143 WESTING HOUSE YAMAHA YORK 004 YUPITERU 043 ZENITH ZONDA 112

117 FISHER FUJI 031 FUNAI 034 GARRARD 034 GE 053 GO VIDEO GOLDSTAR HARLEY DAVIDSON 034 HARMAN KARDON HARWOOD 024 HITACHI 150 HQ 034 HUGHES 004 INSTANTREPLAY 031 JCL 031 JCPENNEY 101 JENSEN 043 JVC 031 KEC KENWOOD KLH 024 KODAK LG LLOYD 034 LOGIK 024 LXI 106 MAGIN 040 MAGNASONIC 117
053 SALORA 014 SAMSUNG SANKY 053 SANSUI 034 SANYO SCOTT SEARS SHARP SHINTOM 024 SHOGUN 040 SINGER 024 SONY 034 SOUNDESIGN 034 STS 004 SYLVANIA SYMPHONIC 034 TANDY TATUNG 043 TEAC TECHNICS TEKNIKA 101 THOMAS 034 TMK TOSHIBA 150 TOTEVISION UNITECH 040 VECTOR RESEARCH 012 VIDEO CONCEPTS 046 VIDEOSONIC 040 WARDS WESTINGHOUSE XR-031 034
*Note : For TV/VCR combination unit, Please use following steps to operate the Volume control. STEP1 Press the [CBL] button and the [SELECT] button simultaneously for 3 seconds. The [CBL] button will light on for 20 seconds. STEP2 Press the [VOL+] button. STEP3 Press the [VCR] button. The LED will blink twice to confirm the programming. VCR(DVD)
AIWA AKAI ALPINE APEX DIGITAL ARCAM CARY AUDIO DESIGN CLASSE COBY CYBERHOME DAEWOO DENON FUNAI GE GOLDSTAR GO VIDEO HARMAN KARDON HITACHI HITEKER INTEGRA JVC KENWODD KISS KLH LG MAGNAVOX MARANTZ MCINTOSH MEMOREX MINTEK MITSUBISHI MYRYAD NAD NAKAMICHI ONKYO OPTIMUS PANASONIC PHILIPS PIONEER
ADC ADCOM AIWA AKAI AMC ANGSTROM ARCAM AUDIO ACCESS AUDIO ALCHEMY AUDIO FILE AUDIO MATRIX AUDIO TECHNICA B&K BOSE BRYSTON CARVER CASIO CHIRO CINEMA SOUND CITATION CLARION CURTIS MATHES DENON ENLIGHTENED AUDIO FISHER FOSGATE AUDIONICS GOLDSTAR HARMAN KARDON HITACHI INKEL INSIGNIA INTEGRA JCPENNEY JENSEN JVC

AUX(TIVO)

PHILIPS SONY 252 253

AUX(DMX & DCR)

DMX-DJ MAESTRO II 254 255

Operating Instructions For Charter Communications 4-in-1 Remote Control

UR4-EXP-CHD2

1 Introduction
The remote control is designed to operate the Scientific-Atlanta Explorer and Motorola DCT set top boxes. You can also control TV's, VCRs DVD's and Audio equipment. CABLE : Cable Converters TV : Televisions VCR : VCRs and DVDs AUX : Audio Receivers, DMX, DCR, etc.

3 Button Functions

STEP4 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. *Tip : The equipment will turn off when the correct three-digit code number has been entered. You can verify you have selected the correct code by pressing the [POWER] button the equipment should turn on or turn off. *Note : If there is more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off. STEP5 Store the three-digit code number by pressing the [SELECT] button. The device LED will blink twice to confirm that the code has been stored. *Note : Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 3 using the next threedigit code number from the same brand list.
*Tip : You can verify that you selected the correct code by pressing the [POWER] button. The equipment should either turn on or turn off. STEP5 Press the same [SELECT] button to store the code. The device LED will blink twice to confirm that the code has been stored.
*Tip : The device LED will stay lit for 20 seconds. The next step must be entered while the LED is on. STEP4 Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. STEP5 Store the three-digit code number by pressing the [SELECT] button. The [AUX] device LED will blink twice to confirm that the code has been stored.
STEP3 Press the [VOL-] button. STEP4 Press the [TV] button. The device LED will blink twice to confirm the programming. To return to original state: If you wish to restore the CABLE channel control in TV mode, repeat the above steps by pressing [CBL] in STEP4.

2 Replacing Batteries

Before you program or operate the remote control, you must install two new AA alkaline batteries. STEP1 Remove the battery compartment cover on the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below. STEP3 Replace the battery compartment cover.
C. To Find the Three Digit Code Number That was Stored in the Device.
STEP1 Press the [SELECT] button and [MUTE] button simultaneously for 3 seconds. The device LED's blink in sequence (TV-VCR-AUX-CBL-TV) STEP2 Release both buttons together when the desired device button is blinking (the device LED will then remain lit) *Tip : The device LED will stay lit for 20 seconds. The next step must be entered while the LED is on. STEP3 Press the [INFO] button. The device LED will blink number of times indicating the number of each digit of the code number. Each digit is separated by a 1 second interval of the LED being turned off. Example : One blink, three blinks and eight blinks with an interval of 1 second of LED being turned off, indicates the code number 138. *Note : Ten blinks is equal to the number 0.
G. Programming Volume Control.
By following the steps below, the you can program the volume controls (Volume UP, Volume Down and MUTE) from one device to operate in another device mode. The default volume control settings on the remote control is as follows: CBL : TV VCR : TV T V : TV AUX : AUX
E. Programming the VOD Button.
This is designed to program the VOD button so that it can access video on demand with one button press. The VOD button is factory defaulted to Ch 999. To re-program to a different channel: STEP1 Press the [CBL] button. STEP2 Press the [VOD] button and the [SELECT] button simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds. STEP3 Press the Numbers of the desired channel to become the new Macro. (e.g. 123) STEP4 Press the [CH+] button to save the new Macro you stored. The [CBL] button will blink twice to confirm.

If you wish to store the CBL volume control in CBL mode, use the following steps. STEP1 Press the [SELECT] button and [MUTE] button simultaneously for 3 seconds. The device LED's blink in sequence (TV-VCR-AUX-CBL-TV) STEP2 Release both buttons together when the [CBL] device LED is blinking (the [CBL] device LED will then remain lit.) *Tip : The device LED will stay lit for 20 seconds. The next step must be entered while the LED is on. STEP3 Press the [VOL+] button. STEP4 Press the [CBL] button. The device LED will blink twice to confirm the programming. To return to original state: If you wish to restore the TV volume control in CBL mode, repeat the above steps by pressing [TV] in STEP4.

B. Auto Search Method.

If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps: STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUX)
F. Programming Channel Control.
By following the steps below, the you can program the channel controls (channel UP, and channel DOWN) from one device to operate in another device mode. The default channel control settings on the remote control is as follows: CBL : CBL VCR : VCR T V : CBL AUX : AUX

4 Operations

Default State: Device Default set to Cable for SA Explorer series. For the Motorola DCT series re-program CBL to code 002. Volume Default: TV volume and mute through the TV, with the option of controlling volume and mute through the Cable box or Audio. Refer to section G for programming the volume and mute through your Cable box or Audio. Channel Default: CABLE channel and number keys through the CABLE, with the option of controlling channel and number keys through the TV or VCR. Refer to section F for programming the channel and number keys through your TV or VCR.
5 Programming the Remote Control
A. Three-Digit Code Programming Method.
The remote control can be programmed by entering in a three-digit code number that corresponds to a particular manufacturer or brand of Audio/Video equipment. The three-digit code numbers are listed in the code table of the instruction manual. STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUX) STEP2 Press the [SELECT] button and [MUTE] button simultaneously for 3 seconds. The device LED's blink in sequence (TV-VCR-AUX-CBL-TV) STEP3 Release both buttons together when the desired device button is blinking (the device LED will then remain lit) *Tip : The device LED will stay lit for 20 seconds. The next step must be entered while the LED is on.

STEP2 Press the [SELECT] button and [MUTE] button simultaneously for 3 seconds. The device LED's blink in sequence (TV-VCR-AUX-CBL-TV) STEP3 Release both buttons together when the desired device button is blinking (the device LED will then remain lit) *Tip : The device LED will stay lit for 20 seconds. The next step must be entered while LED is on. STEP4 Press the [CH+] or [CH-] button one at a time or keep it pressed. The remote will emit a series of power on/off commands. Release the [CH+] or [CH-] button as soon as the equipment turns off.
D. Programming a Second TV to AUX Mode.
STEP1 Press the [SELECT] button and [MUTE] button simultaneously for 3 seconds. The device LED's blink in sequence (TV-VCR-AUX-CBL-TV) STEP2 Release both buttons together when the [AUX] device LED is blinking (the [AUX] device LED will then remain lit.) STEP3 Hold down the [MUTE] button, the device LED's will begin blinking in sequence again. Release the [MUTE] button when the [TV] device LED is blinking. (the [TV] device LED will then remain lit.)
If you wish to store the TV channel control in TV mode, use the following steps. STEP1 Press the [SELECT] button and [MUTE] button simultaneously for 3 seconds. The device LED's blink in sequence (TV-VCR-AUX-CBL-TV) STEP2 Release both buttons together when the [TV] device LED is blinking (the [TV] device LED will then remain lit.) *Tip : The device LED will stay lit for 20 seconds. The next step must be entered while the LED is on.
H. Programming For Advanced Functions
The A, B and C buttons can be re-programmed for the Motorola DCT series converter only. To act as Macro button's to send out up to 10 commands with the press of one button.
Universal Remote Control, Inc.

www.universalremote.com

OCE-0005H Rev 01 (02/12/04)
STEP1 Press the [CBL] button to select the CBL mode. STEP2 Press the [A, B, or C] button and [SELECT] button simultaneously for 3 seconds. The [CBL] device LED will turn on for 20 seconds. STEP3 Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered. STEP4 Press the [CH+] button to store the functions that were selected. The [CBL] device LED will blink twice to confirm the storage of functions.

6 Set-up Code Tables

CABLE TV

Remote

Scientific Atlanta Motorola

MAKER(BRAND) NAME

HITACHI INFINITY INKEL INTEQ JBL JCB JCPENNEY JENSEN JVC KENWOOD KLOSS KTV LG LODGENET LOEWE LOGIK LUXMAN LXI MAGNAVOX MAJESTIC MARANTZ MATSUI MATSUSHITA MEGATRON MEMOREX METZ MGA MIDLAND MINERVA MINUTZ MITSUBISHI MOTOROLA MTC MULTITECH NAD NEC NIKEI NIKKO NTC ONKING ONWA OPTIMUS OPTONICA ORION PANASONIC PHILCO PHILIPS PIONEER PORTLAND PRISM PROSCAN PROTON QUASAR RADIO SHACK RCA REALISTIC RUNCO SAMPO SAMSUNG SANSEI SANSUI SANYO SCOTCH SCOTT SEARS SEMIVOX

Code No

001 002
ADMIRAL ADVENT AIKO AKAI ALARON AMARK AMERICA ACTION AMPRO ANAM AOC APEX DIGITAL AUDIOVOX BAYSONIC BELL&HOWELL BRADFORD BROKSONIC CANDLE CAPEHART CARVER CELEBRITY CETRONIC CINERAL CITIZEN CLASSIC CONCERTO CONTEC CORONADO CRAIG CROSLEY CROWN CURTIS MATHES CXC DAEWOO DAYTRON DENON DUMONT DWIN DYNASTY DYNATECH ELECTROBAND ELECTROHOME EMERSON

I. Low Battery Warning.

When the batteries are low and need to be replaced with fresh batteries, the remote control LED will blink 2 times in sequence whenever a [POWER] button is pressed to turn on equipment.

J. Memory Lock System.

This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
K. Write your device Set-up codes.
TV Set-up Code Number : VCR Set-up Code Number : AUX Set-up Code Number :
FISHER FUJITSU FUNAI FUTURETECH 043 GATEWAY 242 GE 120 GIBRALTER GOLDSTAR GRUNPY HALL MARK 004 HARLEY DAVIDSON 028 HARMAN KARDON 164 HARVARD 043
WESTING HOUSE 076 YAMAHA YORK 004 YUPITERU 043 ZENITH ZONDA 112
ADMIRAL AIKO AIWA AKAI AMERICA ACTION AMERICAN HIGH AMPRO ANAM ASHA AUDIO DYNAMICS AUDIOVOX BEAUMARK BROKSONIC CALIX CANON CAPEHART CCE CINERAL CITIZEN COLT CRAIG CUIRTIS MATHES CYBERNEX DAEWOO DAYTRON DBX DYNATECH
REALISTIC RICO 058 RUNCO 072 SALORA 014 SAMSUNG SANKY 053 SANSUI 034 SANYO SCOTT SEARS SHARP SHINTOM 024 SHOGUN 040 SINGER 024 SONY 034 SOUNDESIGN 034 STS 004 SYLVANIA SYMPHONIC 034 TANDY TATUNG 043 TEAC TECHNICS TEKNIKA 101 THOMAS 034 TMK TOSHIBA 150 TOTEVISION UNITECH 040 VECTOR RESEARCH 012 VIDEO CONCEPTS 046 VIDEOSONIC 040 WARDS WESTINGHOUSE XR-YAMAHA 043 ZENITH 025
*Note : For TV/VCR combination unit, Please use following steps to operate the volume control. STEP1 Press the [SELECT] button and [MUTE] button simultaneously for 3 seconds. The device LED's blink in sequence (TV-VCR-AUX-CBL-TV) STEP2 Release both buttons together when the [CBL] device LED is blinking (the [CBL] device LED will then remain lit.) STEP3 Press the [VOL+] button. STEP4 Press the [VCR] button. The device LED will blink twice to confirm the programming.
ADC ADCOM AIWA AKAI AMC ANGSTROM ARCAM AUDIO ACCESS AUDIO ALCHEMY AUDIO FILE AUDIO MATRIX AUDIO TECHNICA B&K BOSE BRYSTON CARVER

040 090

DMX & DCR(AUX)
DMX-DJ MAESTRO II 254 255