Operating Instructions For 4-Function Cable Remote Control

UR4U-MDVR-CHD2

1 Introduction
This remote control is designed to operate all Motorola and Scientific Atlanta digital set top boxes (including HD and DVR), plus the majority of TVs, VCRs, DVDs and AUDIO equipment on the market as shown below. CABLE : Cable Converters TV : Televisions DVD : DVDs, TV/DVDs, VCRs and TV/VCRs AUX : Audio Receivers and DVRs, etc.

4 Button Functions

A. Quick Set-Up Method
STEP1 Turn on the device you want to programto program your TV, turn the TV on. STEP2 Point the remote at the TV and press and hold the TV key for 3 seconds. While Holding the TV key, the TV LED will light off and on again. Begin to press the number keys, one at a time, starting with 1, then 2, 30 until the TV turns off. STEP3 Release the TV key to save the code. The TV LED will blink twice to confirm the code is stored. Repeat these steps for your DVD, Aux, etc.

C. Auto-Search Method

STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX). STEP2 Press the [COMPONENT] button (TV, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The Component LED will light for 30 seconds indicating the unit is ready to be programmed. STEP3 Point the remote toward the Component and press the [CH ] or [CH ] button one step at a time or keep it pressed. The remote will emit a series of ON/OFF commands. Release the [CH ] or [CH ] button as soon as the Component turns Off. STEP4 Test functions. (Same as for 3-Digit Code Programming Method - Section B). If any of the functions do not work as they should, repeat from STEP 3 using [CH ] or [CH ] buttons to find the correct code. STEP5 Save the code. (Same as for 3-Digit Code Programming Method - Section B). Now, repeat the Auto-Search Method for those Components you could not program earlier with the Pre-Programmed Method.
STEP2 Press the [AUX] button and the [OK/SEL] button simultaneously for 3 seconds.The [AUX] Component LED will light for 30 seconds. STEP3 Press the [COMPONENT] button you want to setup. Point the remote control toward the Component and enter the 3-digit code number assigned to your brand. *Note : If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off. STEP4 Test functions. (Same as for 3-Digit Code Programming Method - Section B). If any of the functions do not work as they should, you need to find a new code. STEP5 Once you have found the correct 3-digit code, save it by pressing the [AUX] button one more time. The Component LED light will blink twice to confirm the code was stored. Now when you press the AUX button, all the buttons will work with that 4th Component.
STEP1 Press the [TV] button and the [OK/SEL] button simultaneously for 3 seconds. The [TV] Component LED will light for 30 seconds. STEP2 Press the [VOL -] button. STEP3 Press the [TV] button again. The Component LED will blink twice to confirm the programming. To return to original state: If you wish to restore the CABLE channel control in TV mode, repeat the above steps but press [CBL] in STEP3.

2 Replacing Batteries

Before you program or operate this remote control, you must first install two new AA Alkaline batteries. STEP1 Remove the battery compartment cover on the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below. STEP3 Replace the battery compartment cover.
H. Programming Volume Control
You can program the volume controls (Volume Up, Volume Down and Mute) from one Component to operate in another Component mode. Default volume control settings on the remote control are as follows: CBL : TV T V : TV DVD : TV AUX : AUX If you wish to operate the CBL volume control in CBL mode, use the following steps. STEP1 Press the [CBL] button and the [OK/SEL] button simultaneously for 3 seconds. The [CBL] Component LED will light for 30 seconds. STEP2 Press the [VOL +] button. STEP3 Press the [CBL] button. The Component LED will blink twice to confirm the programming. To return to original state: If you wish to restore the TV volume control in CBL mode, repeat the above steps but press [TV] in STEP3.

B. Pre-Programmed 3-Digit Code Method
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX). STEP2 Press the [COMPONENT] button (TV, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The Component LED will light for 30 seconds indicating the unit is ready to be programmed. STEP3 Point the remote control toward the Component and enter the 3-digit code number assigned to your brand. *Note : If the 3-digit code number you just entered is correct, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off. STEP4 After youve entered the correct code number and the Component has turned Off, press the [POWER] button to turn the Component back On. Now its time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all work. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand. STEP5 Once you have found the correct 3digit code, save it by pressing the same [COMPONENT] button one more time. The Component LED light will blink twice to confirm that the code was successfully stored. Now, program the rest of your Components by repeating STEPS 1-5. *Note : If the Pre-Programmed Method did not work, or if the Code Tables do not list your Component brand, use the Auto-Search Method as explained in Section C.
F. Programming the System On/Off Button
This allows you to program the System On/Off button so it can send up to four power On/Off commands with one button press. STEP1 Press the [CBL] button. STEP2 Press the [SYSTEM ON/OFF] button and the [OK/SEL] button simultaneously for 3 seconds. The [CBL] Component LED will light for 30 seconds. STEP3 Press the first [COMPONENT] button you want to store in the [SYSTEM ON/OFF] button and then the [POWER] button. Repeat this for other Components until you have stored all the desired power commands into the [SYSTEM ON/OFF] button. STEP4 Press the [CH+] button to save the power commands you stored. The [CBL] button will blink twice to confirm the commands have been saved.
D. Finding a Component Buttons Setup Code Number
If you used the Auto-Search Method to program a Component, you may not know what the correct code number is. Here is a way for you to identify the code number, so you can record it for future reference. STEP1 Press the [COMPONENT] button (TV, DVD or AUX) you want to verify and the [OK/SEL] button simultaneously for 3 seconds. The Component LED will light for 30 seconds. STEP2 Press the [INFO] button and count the number of times the Component LED light blinks. This number indicates the first digit of the code, followed by the second and third, each separated by a one second pause when the LED will turn off. *Note : 10 blinks represents the number zero. Example : One blink, (pause), eight blinks, (pause) and three blinks, indicates code number 183.

I. Programming a Favorite Channel
See on-screen Guide Menu.
5 Programming the Remote Control 3 Operations
DEFAULT STATUS: Component Default: CABLE Channel Default: CABLE channel +/- and numbers operate through the CABLE box. You have the option of controlling channel +/and numbers through the TV, VCR or DVD. Refer to section G for programming steps. Volume Default: CABLE volume +/- and mute operate through the TV. You have the option of controlling volume through the Cable box, VCR or DVD. Refer to section H for programming steps.
There are three ways you can program your remote control:

J. Low Battery Warning

When the batteries are low and need to be replaced with fresh batteries, the Component LED lights will blink 2 times in sequence whenever a [POWER] button is pressed to turn on equipment.
* Quick Set-Up Method rogrammed * The Pre-Programm 3-Digit Code Method * The Auto-Search Method The Quick Set-Up Method is a unique new feature that enables the fastest and easiest set-up by using one-digit codes for up to 10 major brands for each component. The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code numbers that correspond to a particular Components manufacturer/brand, so its the fastest and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The AutoSearch Method scans through all the codes in the remote control, one at a time. IMPORTANT SETUP NOTES: This pertains to all programming steps. When you are in setup mode in each component, a component LED will light up for 30 seconds. If you do not press a button within 30 seconds, the LED light will turn off and exit setup mode and you will need to start over. When programming a combo unit, program as a VCR or DVD first.

K. Memory Lock System

This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

G. Programming Channel Control
You can program the channel controls (Channel Up, Channel Down, Last and Numbers) from one Component to operate in another Component mode. Default channel control settings on the remote control are as follows: CBL : CBL DVD : DVD T V : CBL AUX : AUX
E. AUX Function: Programming a 4 th Component
You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio Component. STEP1 Turn on the 4th Component you want to program (TV, VCR, DVD or Audio).
L. Record Your Component Set-up Codes
TV DVD AUX Set-up Code Number: Set-up Code Number: Set-up Code Number:
Universal Remote Control, Inc.

www.universalremote.com

OCE-0053A REV 15(04/21/10)
If you wish to operate the TV channel control in TV mode, use the following steps.
For additional information about your remote control, go to www.universalremote.com

6 Set-up Code Tables

CABLE Converter

Remote Converter

All Motorola digital set top boxes (including HD & DVR) All Scientific Atlanta digital set top boxes (including HD & DVR) EVOLUTION FTA nFusion FTA receivers MOXI HD DVR set top boxes SKY +HD set top boxes SKY HD set top boxes TELNET HD box WEGENER

Manufacturer/Brand

FUTURETECH GATEWAY GE GEM GIBRALTER GOLDSTAR GRUNPY HAIER HALL MARK HANNSPREE HARLEY DAVIDSON HARVARD HAVERMY HELLO KITTY HIMITSU HISENSE HITACHI HP HUMAX HYPERION HYUNDAI ILO INFINITY INFOCUS INSIGNIA INTEQ JANEIL JBL JCB JCPENNEY JENSEN JVC KAWASHO KEC KENWOOD KLEGG KLOSS KONKA KREISEN KTV KURAZAI LG LODGENET LOEWE LOGIK LUXMAN LXI MAGNAVOX MAJESTIC MARANTZ MATSUI MATSUSHITA MAXENT MEGATRON MEMOREX MGA MIDLAND MINTEK MINUTZ MITSUBISHI MONTGOMERY WARD MOTOROLA MTC MULTITECH NAD NEC NET TV NIKEI NIKKO NIKO NORCENT NTC NUVISION OLEVIA ONKING ONWA OPTIMUS OPTONICA OPTOMA ORION PANASONIC PHILCO PHILIPS PILOT PIONEER POLAROID PORTLAND PRISM PROSCAN PROTON PROTRON

Set-Up Code Number

499 500

DVD-DVD Recorders

057 091

DVD-VCR

Set-Up Code Number Manufacturer/Brand
GOLDSTAR GRADIENTE HARLEY DAVIDSON HARMAN KARDON HARWOOD HITACHI HQ INSTANTREPLAY JCL JCPENNEY JENSEN JVC KEC KENWOOD KLH KODAK LG LLOYD LOGIK LXI MAGIN MAGNAVOX MARANTZ MARTA MATSUI MATSUSHITA MEI MEMOREX MGA MGN TECHNOLOGY MINOLTA MITSUBISHI MOTOROLA MTC MULTITECH NEC NIKKO NOBLEX NORDMENDE OLYMPUS OPTIMUS OPTONICA PANASONIC PENTAX PHILCO PHILIPS PILOT PIONEER PORTLAND PROFITRONIC PROTEC PULSAR QUARTZ QUASAR RADIO SHACK RADIX RANDEX RCA REALISTIC RICO RUNCO SAMSUNG SANKY SANSUI SANYO SCOTT SEARS SHARP SHINTOM SHOGUN SIGNATURE SINGER SONY SOUNDESIGN STS SYLVANIA SYMPHONIC TANDY TATUNG TEAC TECHNICS TEKNIKA THOMAS TMK TOSHIBA TOTEVISION UNITECH VECTOR RESEARCH VICTOR VIDEO CONCEPTS VIDEOSONIC VILLAIN

DVD-TV/DVD/VCR Combos

EMERSON MAGNAVOX PANASONIC SUPERSCAN SYLVANIA TOSHIBA 143 164
ADC ADCOM AIWA AKAI AMC ANGSTROM ANTHEM ARAGON ARCAM ATLANTIC TECHNOLOGY AUDIO FILE AUDIO MATRIX AUDIO TECHNICA B&K BOSE BOSTON ACOUSTICS CAMBRIGE AUDIO CARVER CARY AUDIO DESIGN CINEMA SOUND CITATION CLARION DELPHI DENON DIGITAL PROJECTION ELAN ENLIGHTENED AUDIO FISHER FLEXTRONICS FOSGATE AUDIONICS GE GOLDSTAR HARMAN KARDON HITACHI INSIGNIA INTEGRA JAMO JCPENNEY JENSEN JVC KENWOOD KLEGG KLH KLIPSCH KOSS KRELL KYOCERA LEXICON LINN LUXMAN LXI MAGNAVOX MARANTZ MCINTOSH MERIDIAN MITSUBISHI

DVD-DVD/VCR Combos

GO VIDEO PANASONIC PHILIPS RCA SAMSUNG SANSUI SONY TOSHIBA ZENITH

AUX-DVR(TIVO)

DIRECTV DSTV HUGHES HUMAX ICREALTIME MOXI PHILIPS RCA REPLAY NETWORKS SONY TIVO TOSHIBA 817 817
066 (VCR Functions for VCR 567) 027 (VCR Functions for VCR 644) (VCR Functions for VCR 601)
ADMIRAL ADVENTURA AIKO AIWA AKAI AMERICA ACTION AMERICAN HIGH AMPRO ANAM ASHA AUDIO DYNAMICS AUDIOVOX BEAUMARK BROKSONIC CALIX CANON CAPEHART CCE CITIZEN COLT CRAIG CURTIS MATHES CYBERNEX DAEWOO DAYTRON DBX DYNATECH ELECTROHOME ELECTROPHONIC EMERSON FISHER FUJI FUNAI GARRARD GE GO VIDEO

645 602

AUX-iPod Controls
APPLE / iPod BOSE TEN TECHNOLOGY 901

AUX-Media PCs

DELL GATEWAY HP SONY TOSHIBA WINBOOK 761 761

AUX-Gaming Systems

MICROSOFT / XBOX SONY / PS908 914
ADCOM AIWA AKAI ALLEGRO APEX DIGITAL ARCAM BLAUPUNKT BROKSONIC CAMBRIDGE AUDIO CARY AUDIO DESIGN CINEVISION 266 091

AUX-Lighting Controls

LUTRON X-658 683
GO VIDEO CYBERHOME ILO KISS LITEON PANASONIC 138
AUX-Digital to Analog Converter box

ZINWELL 593