Operating Instructions For The UR5-MDVR Cable Remote Control

UR5-MDVR

1 Introduction
The remote control is designed to operate the Motorola DCT6208 advanced HD set top and the Motorola DCT2XXX, DCT5XXX Series set tops. You can also control the majority of TV, VCR, DVD and AUDIO equipment on the market as shown below. CABLE : Cable Converters TV : Televisions VCR : VCRs and TV/VCRs DVD : DVD Players AUX : Audio Receivers, etc.

3 Button Functions

*Tip : The equipment will turn off when the correct three-digit code number has been entered. You can verify you have selected the correct code by pressing the [POWER] button, the equipment should turn on or turn off. *Note : If there is more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off. STEP4 Store the three-digit code number by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored. *Note : Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 2 using the next three-digit code number from the same brand list.
C. To Find the Three Digit Code Number That was Stored in the Device.
STEP1 Press the [DEVICE] button (TV, VCR , DVD or AUX) you wish to verify and the [OK] button simultaneously for 3 seconds. The device LED will turn on. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [INFO] button. The device LED will blink number of times indicating the number of each digit of the code number. Each digit is separated by a 1 second interval of the LED being turned off. Example : One blink, three blinks and eight blinks with an interval of 1 second of LED being turned off, indicates the code number 138. Note : Ten blinks is equal to the number 0.
STEP3 Press the [DEVICE] button and the [POWER] button you wish to store in the [SYSTEM ON/OFF] button and repeat this until you stored all the power commands into the [SYSTEM ON/OFF] button. STEP4 Press the [CH+] button to save the power commands you stored. The [CBL] button will blink twice to confirm the saving.
STEP1 Press the [CBL] button and the [OK] button simultaneously for 3 seconds. The [CBL] device LED will turn on. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [VOL +] button. STEP3 Press the [CBL] button. The device LED will blink twice to confirm the programming. To return to original state: If you wish to restore the TV volume control in CBL mode, repeat the above steps by pressing [TV] in STEP3.
F. Programming Channel Control.
By following the steps below, the user can program the channel controls (Channel Up, Channel Down and Last) from one device to operate in another device mode. The default channel control settings on the remote control are as follows: CBL : CBL VCR : CBL AUX : AUX T V : CBL DVD : DVD

2 Replacing Batteries

Before you program or operate the remote control, you must install two new AA alkaline batteries. STEP1 Remove the battery compartment cover on the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown In the illustration below. STEP3 Replace the battery compartment cover.
H. Programming For Advanced Function.
In the CBL mode, the VOD and PPV buttons can be programmed to act as a macro or favorite channel button. You can send out up to ten commands with one button press. STEP1 Press the [CBL] button to select the CBL mode. STEP2 Press the [VOD or PPV] button and [OK] button simultaneously for 3 seconds. The [CBL] device LED will turn on for 20 seconds. STEP3 Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered. STEP4 Press the [CH+] button to store the functions that were selected. The [CBL] device LED will blink twice to confirm the storage of functions.

B. Auto Search Method

If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps: STEP1 Turn on the equipment you wish to operate. STEP2 Press the [DEVICE] button (TV, VCR, DVD or AUX) to be programmed and the [OK] button simultaneously for 3 seconds. The device LED will turn on.
D. Programming a second TV to AUX Mode.
STEP1 Press the [AUX] button to be programmed and the [OK] button simultaneously for 3 seconds.The [AUX] device LED will turn on. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [TV] device button to pick up the TV code table. STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. STEP4 Store the three-digit code number by pressing the [AUX] button once again. The device LED will blink twice to confirm that the code has been stored.
If you wish to store the TV channel control in TV mode, use the following steps. STEP1 Press the [TV] button and the [OK] button simultaneously for 3 seconds. The [TV] device LED will turn on. *Tip : The device LED will light on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [VOL -] button. STEP3 Press the [TV] button. The device LED will blink twice to confirm the programming. To return to original state: If you wish to restore the CABLE channel control in TV mode, repeat the above steps by pressing [CBL] in STEP3.

I. Low Battery Warning.

When the batteries are low and need to be replaced with fresh batteries, the remote control LED will blink 2 times in sequence whenever a [POWER] button is pressed to turn on equipment.

4 Operations

Default State: Device Default: CABLE Volume Default: You have the option of controlling your TV volume through the Cable box, VCR or DVD. Refer to section G for programming the volume through your Cable box, VCR or DVD. Channel Default: You have the option of controlling your CABLE channel and number keys through the TV or VCR. Refer to section F for programming the channel and number keys through your TV or VCR.
5 Programming the Remote Control
A. Three-Digit Code Programming Method.

The remote control can be programmed by pressing in a three-digit code number that corresponds to particular manufacturers and brands of Audio/Video equipment. The three-digit code numbers are listed in the code table of the instruction manual. STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUX) STEP2 Press the [DEVICE] button (TV, VCR, DVD or AUX) to be programmed and [OK] button simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready to be programmed. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables.
*Tip : The device LED will turn on for 20 seconds. The next step must be entered while LED is on. STEP3 Press the [CH+] or [CH-] button one at a time or keep it pressed. The remote will emit a series of power on/off commands. Release the [CH+] or [CH-] button as soon as the equipment turns off. *Tip : You can verify that you selected the correct code by pressing the [POWER] button. The equipment should either turn on or turn off. STEP4 Press the same [DEVICE] button to store the code. The device LED will blink twice to confirm that the code has been stored.
G. Programming Volume Control.
By following the steps below, the user can program the volume controls (Volume Up and Volume Down) from one device to operate in another device mode. The default volume control settings on the remote control are as follows: CBL : TV VCR : TV AUX : AUX T V : TV DVD : TV

J. Memory Lock System.

This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
E. Programming the System On/Off Button.
This is designed to program the System On/Off button so that it can send out up to five power on/off commands with one button press. STEP1 Press the [CBL] button. STEP2 Press the [SYSTEM ON/OFF] button and the [OK] button simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds.
K.Write your device Set-up codes.
TV VCR DVD AUX Set-up Code Number: Set-up Code Number: Set-up Code Number: Set-up Code Number:
Universal Remote Control, Inc.

www.universalremote.com

OCE-0017C REV 04 (11/29/05)
System On/Off button: This button is designed to send out power commands for two, three, four or all five devices with one button press. Please refer to section E for details.
If you wish to store the CBL volume control in CBL mode, use the following steps.

Operating Instructions For The UR5-MDVR Cable Remote Control

UR5-MDVR

1 Introduction
The remote control is designed to operate the Motorola DCT6208 advanced HD set top and the Motorola DCT2XXX, DCT5XXX Series set tops. You can also control the majority of TV, VCR, DVD and AUDIO equipment on the market as shown below. CABLE : Cable Converters TV : Televisions VCR : VCRs and TV/VCRs DVD : DVD Players AUX : Audio Receivers, etc.

3 Button Functions

*Tip : The equipment will turn off when the correct three-digit code number has been entered. You can verify you have selected the correct code by pressing the [POWER] button, the equipment should turn on or turn off. *Note : If there is more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off. STEP4 Store the three-digit code number by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored. *Note : Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 2 using the next three-digit code number from the same brand list.
C. To Find the Three Digit Code Number That was Stored in the Device.
STEP1 Press the [DEVICE] button (TV, VCR , DVD or AUX) you wish to verify and the [OK] button simultaneously for 3 seconds. The device LED will turn on. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [INFO] button. The device LED will blink number of times indicating the number of each digit of the code number. Each digit is separated by a 1 second interval of the LED being turned off. Example : One blink, three blinks and eight blinks with an interval of 1 second of LED being turned off, indicates the code number 138. Note : Ten blinks is equal to the number 0.
STEP3 Press the [DEVICE] button and the [POWER] button you wish to store in the [SYSTEM ON/OFF] button and repeat this until you stored all the power commands into the [SYSTEM ON/OFF] button. STEP4 Press the [CH+] button to save the power commands you stored. The [CBL] button will blink twice to confirm the saving.
STEP1 Press the [CBL] button and the [OK] button simultaneously for 3 seconds. The [CBL] device LED will turn on. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [VOL +] button. STEP3 Press the [CBL] button. The device LED will blink twice to confirm the programming. To return to original state: If you wish to restore the TV volume control in CBL mode, repeat the above steps by pressing [TV] in STEP3.
F. Programming Channel Control.
By following the steps below, the user can program the channel controls (Channel Up, Channel Down and Last) from one device to operate in another device mode. The default channel control settings on the remote control are as follows: CBL : CBL VCR : CBL AUX : AUX T V : CBL DVD : DVD

2 Replacing Batteries

Before you program or operate the remote control, you must install two new AA alkaline batteries. STEP1 Remove the battery compartment cover on the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown In the illustration below. STEP3 Replace the battery compartment cover.
H. Programming For Advanced Function.
In the CBL mode, the VOD and PPV buttons can be programmed to act as a macro or favorite channel button. You can send out up to ten commands with one button press. STEP1 Press the [CBL] button to select the CBL mode. STEP2 Press the [VOD or PPV] button and [OK] button simultaneously for 3 seconds. The [CBL] device LED will turn on for 20 seconds. STEP3 Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered. STEP4 Press the [CH+] button to store the functions that were selected. The [CBL] device LED will blink twice to confirm the storage of functions.

B. Auto Search Method.

If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps: STEP1 Turn on the equipment you wish to operate. STEP2 Press the [DEVICE] button (TV, VCR, DVD or AUX) to be programmed and the [OK] button simultaneously for 3 seconds. The device LED will turn on.
D. Programming a second TV to AUX Mode.
STEP1 Press the [AUX] button to be programmed and the [OK] button simultaneously for 3 seconds.The [AUX] device LED will turn on. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [TV] device button to pick up the TV code table. STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. STEP4 Store the three-digit code number by pressing the [AUX] button once again. The device LED will blink twice to confirm that the code has been stored.

If you wish to store the TV channel control in TV mode, use the following steps. STEP1 Press the [TV] button and the [OK] button simultaneously for 3 seconds. The [TV] device LED will turn on. *Tip : The device LED will light on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [VOL -] button. STEP3 Press the [TV] button. The device LED will blink twice to confirm the programming. To return to original state: If you wish to restore the CABLE channel control in TV mode, repeat the above steps by pressing [CBL] in STEP3.

I. Low Battery Warning.

When the batteries are low and need to be replaced with fresh batteries, the remote control LED will blink 2 times in sequence whenever a [POWER] button is pressed to turn on equipment.

4 Operations

Default State: Device Default: CABLE Volume Default: You have the option of controlling your TV volume through the Cable box, VCR or DVD. Refer to section G for programming the volume through your Cable box, VCR or DVD. Channel Default: You have the option of controlling your CABLE channel and number keys through the TV or VCR. Refer to section F for programming the channel and number keys through your TV or VCR.
5 Programming the Remote Control
A. Three-Digit Code Programming Method.
The remote control can be programmed by pressing in a three-digit code number that corresponds to particular manufacturers and brands of Audio/Video equipment. The three-digit code numbers are listed in the code table of the instruction manual. STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUX) STEP2 Press the [DEVICE] button (TV, VCR, DVD or AUX) to be programmed and [OK] button simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready to be programmed. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables.
*Tip : The device LED will turn on for 20 seconds. The next step must be entered while LED is on. STEP3 Point the remote control toward the equipment and alternately press the [CH+] (or [CH-]) button and the [POWER] button. If the right code number is sent, the equipment will turn off. *Tip : You can verify that you selected the correct code by pressing the [POWER] button again. The equipment should either turn on or off. STEP4 Press the same [DEVICE] button to store the code. The device LED will blink twice to confirm that the code has been stored.

G. Programming Volume Control.
By following the steps below, the user can program the volume controls (Volume Up and Volume Down) from one device to operate in another device mode. The default volume control settings on the remote control are as follows: CBL : TV VCR : TV AUX : AUX T V : TV DVD : TV

J. Memory Lock System.

This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
E. Programming the System On/Off Button.
This is designed to program the System On/Off button so that it can send out up to five power on/off commands with one button press. STEP1 Press the [CBL] button. STEP2 Press the [SYSTEM ON/OFF] button and the [OK] button simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds.
K.Write your device Set-up codes.
TV VCR DVD AUX Set-up Code Number: Set-up Code Number: Set-up Code Number: Set-up Code Number:
Universal Remote Control, Inc.

www.universalremote.com

OCE-0017C REV 03 (01/24/05)
System On/Off button: This button is designed to send out power commands for two, three, four or all five devices with one button press. Please refer to section E for details.
If you wish to store the CBL volume control in CBL mode, use the following steps.

6 Set-up Code Tables

CABLE TV

Remote

Converter Code No
MAKER(BRAND) NAME GATEWAY GE CODE NUMBER (3 DIGIT) LIST GIBRALTER GOLDSTAR / LG GRUNPY HALL MARK 004 HARLEY DAVIDSON HARVARD 043 HITACHI INFINITY 164 INKEL 129 INTEQ 073 JBL 164 JCB 001 JCPENNEY JENSEN 013 JVC KENWOOD KLOSS KTV LODGENET 072 LOEWE 207 LOGIK 072 LUXMAN 004 LXI MAGNAVOX 229 MAJESTIC 072 MARANTZ MATSUI 164 MATSUSHITA 080 MEGATRON 004 MEMOREX 096 METZ 088 MGA MIDLAND 073 MINERVA 088 MINUTZ 008 MITSUBISHI 224 MOTOROLA 081 MTC MULTITECH 043 NAD NEC NIKEI 043 NIKKO 103 NTC 103 ONKING 043 ONWA 043 OPTIMUS 080 OPTOMA 230 OPTONICA ORION 028 PANASONIC PHILCO 143 164
MAKER(BRAND) NAME PHILIPS CODE NUMBER (3 DIGIT) LIST PIONEER 220 PORTLAND 103 PRISM 034 PROSCAN PROTON 112 QUASAR RADIO SHACK 043 RCA 081 REALISTIC RUNCO 181 SAMPO SAMSUNG 221 SANSEI 120 SANSUI 096 SANYO 020 SCEPTRE 250 SCOTCH 004 SCOTT SEARS SELECO 189 SEMIVOX 043 SEMP 015 SHARP SIGNATURE 072 SOLE SONY 139 SOUNDESIGN SPECTRICON 112 SQUAREVIEW 052 SSS STARLITE 043 SUPRE MACY 002 SUPREME 001 SYLVANIA 211 SYMPHONIC TANDY 081 TATUNG TECHNICS TECHNOL ACE 028 TECHWOOD 004 TEKNIKA 164 TELERENT 072 TERA 172 THOMPSON 210 TMK 004 TNCI 073 TOSHIBA 233 TOTEVISION 143 UNIVERSAL VIDEO CONCEPTS 146 VIDIKRON 164 VIDTECH 004 VIEWSONIC 249

MAKER(BRAND) NAME WARDS CODE NUMBER (3 DIGIT) LIST 143 WESTINGHOUSE YAMAHA YORK 004 YUPITERU 043 ZENITH ZONDA 112

VCR & TV/VCR

MAKER(BRAND) NAME JENSEN JVC KEC KENWOOD KLH KODAK LLOYD LOGIK LXI MAGIN MAGNASONIC MAGNAVOX MARANTZ MARTA MATSUI MATSUSHITA MEI MEMOREX CODE NUMBER (3 DIGIT) LIST MGA 059 MGN TECHNOLOGY 040 MINOLTA 004 MITSUBISHI 053 MOTOROLA MTC MULTITECH NEC NIKKO 101 NOBLEX 040 NORDMENDE 043 OLYMPUS 031 OPTIMUS OPTONICA ORION 025 PANASONIC 163 PENTAX 063 PHILCO PHILIPS PILOT 101 PIONEER 048 PORTLAND 108 PROFITRONIC 040 PROTEC 024 PULSAR 072 QUARTZ 014 QUASAR RADIO SHACK RADIX 101 RANDEX 101 RCA REALISTIC RICO 058 RUNCO 072 SALORA 014 SAMSUNG 124 SANKY 053 SANSUI 034 SANYO 040 134
MAKER(BRAND) NAME SCOTT SEARS CODE NUMBER (3 DIGIT) LIST SHARP SHINTOM 024 SHOGUN 040 SINGER 024 SONY 034 SOUNDESIGN 034 STS 004 SYLVANIA SYMPHONIC 034 TANDY TATUNG 043 TEAC TECHNICS TEKNIKA 101 THOMAS 034 TMK TOSHIBA 150 TOTEVISION UNITECH 040 VECTOR RESEARCH 012 VIDEO CONCEPTS 046 VIDEOSONIC 040 WARDS WESTINGHOUSE XR-YAMAHA 043 ZENITH 025

DVD & TV/DVD

MAKER(BRAND) NAME MITSUBISHI MYRYAD NAD NAKAMICHI ONKYO OPTIMUS PANASONIC PHILIPS PIONEER PROCEED PROSCAN RCA SAMSUNG SANYO SHARP SONY SYLVANIA SYMPHONIC TATUNG TECHNICS THETA DIGITAL TOSHIBA VENTURER YAMAHA ZENITH CODE NUMBER (3 DIGIT) LIST 239

AUDIO(AUX)

MAKER(BRAND) NAME JCPENNEY JENSEN JVC KENWOOD KOSS KRELL KYOCERA LEXICON LUXMAN LXI MAGNAVOX MARANTZ MCINTOSH MCS MERIDIAN MITSUBISHI MONDIAL NAD NAKAMICHI NEC ONKYO OPTIMUS PANASONIC PARASOUND PHILIPS PIONEER PROCEED QUASAR RCA REALISTIC ROTEL SAMSUNG SANSUI SANYO SCOTT SEARS SHARP SHERWOOD SONY SOUNDESIGN SSI TEAC TECHNICS THETA DIGITAL TOSHIBA YAMAHA ZENITH CODE NUMBER (3 DIGIT) LIST 106
Motorola DCTMotorola DCT2XXX and Motorola DCT5XXX Series UR5-MDVR Scientific-Atlanta Explorer 8000, Pioneer Voyager DVR, Pace Micro 001 DVR Series.
MAKER(BRAND) NAME ADMIRAL ADVENT AIKO AKAI ALARON AMARK AMERICA ACTION AMPRO ANAM AOC APEX DIGITAL AUDIOVOX BAYSONIC BELL&HOWELL BRADFORD BROKSONIC CANDLE CAPEHART CARVER CELEBRITY CETRONIC CINERAL CITIZEN CLASSIC CONCERTO CONTEC CORONADO CRAIG CROSLEY CROWN CURTIS MATHES CXC DAEWOO CODE NUMBER (3 DIGIT) LIST DAYTRON DENON 011 DUMONT DWIN 161 DYNASTY 043 DYNATECH 062 ELECTROBAND 001 ELECTROHOME 143 EMERSON 154 FISHER FUJITSU FUNAI FUTURETECH 043
MAKER(BRAND) NAME ADMIRAL AIKO AIWA AKAI AMERICA ACTION AMERICAN HIGH AMPRO ANAM ASHA AUDIO DYNAMICS AUDIOVOX BEAUMARK BROKSONIC CALIX CANON CAPEHART CCE CINERAL CITIZEN COLT CRAIG CUIRTIS MATHES CYBERNEX DAEWOO DAYTRON DBX DYNATECH ELECTROHOME ELECTROPHONIC EMERSON FISHER FUJI FUNAI GARRARD GE GO VIDEO GOLDSTAR / LG HARLEY DAVIDSON HARMAN KARDON HARWOOD HITACHI HQ HUGHES INSTANTREPLAY JCL JCPENNEY CODE NUMBER (3 DIGIT) LIST 040 101
MAKER(BRAND) NAME ADC ADCOM AIWA AKAI AMC ANGSTROM ARCAM AUDIO ACCESS AUDIO ALCHEMY AUDIO FILE AUDIO MATRIX AUDIO TECHNICA B&K BOSE BRYSTON CARVER CASIO CHIRO CINEMA SOUND CITATION CLARION CURTIS MATHES DENON ENLIGHTENED AUDIO FISHER FOSGATE AUDIONICS GOLD STAR / LG HARMAN KARDON HITACHI INKEL CODE NUMBER (3 DIGIT) LIST 005