Operating Instructions For

1 Introduction

The CLIKRTM-5 UR5U-8520 is designed to operate Scientific-Atlanta, Pioneer, Voyager and Pace Micro digital set top boxes (including DVR & HD), plus the majority of TV, VCR, DVD and AUDIO equipment on the market as shown below. CABLE : Cable Converters TV : Televisions VCR : VCRs and TV/VCRs DVD: DVD Players AUX : Audio Receivers and DVRs, etc.

4 Button Functions

Cable Remote Control

UR5U-8520

CLIKR -5
STEP2 Press the [COMPONENT] button (TV, VCR, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds indicating the unit is ready to be programmed. STEP3 Point the remote control toward the Component and enter the 3-digit code number assigned to your brand. *Note : If the 3-digit code number you just entered is correct, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off. STEP4 After youve entered the correct code number and the Component has turned Off, press the [POWER] button to turn the Component back On. Now its time to test the VOLUME and CHANNEL buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all work. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand. STEP5 Once you have found the correct 3-digit code, save it by pressing the same [COMPONENT] button one more time. The Component LED light will blink twice to confirm that the code was successfully stored. Now, program the rest of your Components by repeating STEPS 1-5. *Note : If the Pre-Programmed Method did not work, or if the Code Tables do not list your Component brand, use the Auto-Search Method as explained in Section B.
STEP5 Save the code. (Same as for 3-Digit Code
STEP5 Once you have found the correct 3-digit
Programming Method - Section A). Now, repeat the Auto-Search Method for those Components you could not program earlier with the Pre-Programmed Method.
code, save it by pressing the [AUX] button one more time. The Component LED light will blink twice to confirm the code was stored. Now when you press the AUX button, all the buttons will work with that 5th Component.

CBL : TV DVD : TV

T V : TV AUX : AUX

VCR : TV

C. Finding a Component Buttons Setup Code Number
If you used the Auto-Search Method to program a Component, you may not know what the correct code number is. Here is a way for you to identify the code number, so you can record it for future reference. STEP1 Press the [COMPONENT] button (TV, VCR, DVD or AUX) you want to verify and the [OK/SEL] button simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds. STEP2 Press the [INFO] button and count the number of times the Component LED light blinks. This number indicates the first digit of the code, followed by the second and third, each separated by a one second pause when the LED will turn off. *Note : 10 blinks represents the number zero. Example :One blink, (pause), eight blinks, ( pause) and three blinks, indicates code number 183.
E. Programming the System On/Off Button
This allows you to program the System On/Off button so it can send up to five power On/Off commands with one button press. STEP1 Press the [CBL] button. STEP2 Press the [SYSTEM ON/OFF] button and the [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds. STEP3 Press the first [COMPONENT] button you want to store in the [SYSTEM ON/OFF] button and then the [POWER] button. Repeat this for other Components until you have stored all the desired power commands into the [SYSTEM ON/OFF] button. STEP4 Press the [CH+] button to save the power commands you stored. The [CBL] button will blink twice to confirm the commands have been saved.

2 Replacing Batteries

Before you program or operate the remote control, you must install two new AA alkaline batteries. STEP1 Remove the battery compartment cover on the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below. STEP3 Replace the battery compartment cover.
If you wish to store the CBL volume control in CBL mode, use the following steps. STEP1 Press the [CBL] button and the [OK/SEL] button simultaneously for 3 seconds. The [CBL] Component LED will turn on for 30 seconds. STEP2 Press the [VOL +] button. STEP3 Press the [CBL] button. The Component LED will blink twice to confirm the programming. To return to original state: If you wish to restore the TV volume control in CBL mode, repeat the above steps but press [TV] in STEP3.

H. Programming a Macro or Favorite Channel
In CBL mode, the M1, M2, HELP and BLANK buttons can be programmed to act as a Macro or Favorite Channel button. This allows you to send up to 10 commands with one button press. STEP1 Press the [CBL] button to select the CBL mode. STEP2 Press the M1, M2, HELP or BLANK button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] Component LED will turn on for 30 seconds. STEP3 Press up to 10 buttons you wish to store. The [CBL] Component LED will blink once for each command entered. STEP4 Press the [CH+] button to store the commands that were selected. The [CBL] Component LED will blink twice to confirm the storage of commands.
F. Programming Channel Control
You can program the channel controls (Channel Up, Channel Down and Last) from one Component to operate in another Component mode. Default channel control settings on the remote control are as follows: CBL : CBL DVD : DVD T V : CBL AUX : AUX VCR : CBL
D. AUX Function: Programming a 5 th Component
You can take advantage of the AUX function to program a 5th Component such as a second TV, VCR, DVD or Audio Component. STEP1 Turn on the 5th Component you want to program (TV, VCR, DVD or Audio) using your old remote. STEP2 Press the [AUX] button and the [OK/SEL] button simultaneously for 3 seconds.The [AUX] Component LED will turn on for 30 seconds. STEP3 Press the [COMPONENT] button you want to setup. Point the remote control toward the Component and enter the 3-digit code number assigned to your brand. *Note : If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off
STEP4 Test functions. (Same as for 3-Digit Code

B. Auto-Search Method

STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX) using your old remote. STEP2 Press the [COMPONENT] button (TV, VCR, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds indicating the unit is ready to be programmed. STEP3 Point the remote toward the Component and press the [CH ] or [CH ] button one step at a time or keep it pressed. The remote will emit a series of ON/OFF commands. Release the [CH ] or [CH ] button as soon as the Component turns Off. STEP4 Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, repeat from STEP 3 using [CH ] or [CH ] buttons to find the correct code.

5 Programming the Remote Control 3 Operations
DEFAULT STATES: Component Default: CABLE Channel Default: CABLE channel and number keys through the CABLE. You have the option of controlling your CABLE channel and number keys through the TV or VCR. Refer to section F for programming steps. Volume Default: TV volume and mute keys through the TV. You have the option of controlling your TV volume and mute through the Cable box, VCR or DVD. Refer to section G for programming steps. There are two ways you can program your CLIKRTM-5 remote: * The Pre-Programmed 3-Digit Code Method * The Auto-Search Method The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code numbers that correspond to a particular Components manufacturer/brand, so its the fastest and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The Auto-Search Method scans through all the codes in the remote control, one at a time. IMPORTANT SETUP NOTE! This pertains to all programming steps. When you are in setup mode, a component LED will light for 30 seconds.If you do not press a button within 30 seconds, the LED light will turn off and exit setup mode and you will need to start over.
If you wish to store the TV channel control in TV mode, use the following steps. STEP1 Press the [TV] button and the [OK/SEL] button simultaneously for 3 seconds. The [TV] Component LED will turn on for 30 seconds. STEP2 Press the [VOL -] button. STEP3 Press the [TV] button again. The Component LED will blink twice to confirm the programming. To return to original state: If you wish to restore the CABLE channel control in TV mode, repeat the above steps but press [CBL] in STEP3.

I. Low Battery Warning

When the batteries are low and need to be replaced with fresh batteries, the Component LED lights will blink 2 times in sequence whenever a [POWER] button is pressed to turn on equipment.

J. Memory Lock System

This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
K. Record Your Component Set-up Codes
TV VCR DVD AUX Set-up Code Number: Set-up Code Number: Set-up Code Number: Set-up Code Number:
G. Programming Volume Control
You can program the volume controls (Volume Up, Volume Down and Mute) from one Component to operate in another Component mode. Default volume control settings on the remote control are as follows:

Universal Remote Control, Inc.

www.universalremote.com

OCE-0045C REV 02 (05/06/06)
A. Pre-Programmed 3-Digit Code Method
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX) using your old remote.
Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code.

6 Set-up Code Tables

CABLE Converter

Remote

Converter Code No
001 Scientific-Atlanta Explorer 8000, UR5U-8520 Pioneer Voyager DVR, Pace Micro DVR Series.

Manufacturer/Brand

FUTURETECH GATEWAY GE
Set-Up Code Number Manufacturer/Brand
PILOT PIONEER POLAROID PORTLAND PRISM PROSCAN PROTON PULSAR QUASAR RADIO SHACK RCA REALISTIC ROCTEC RUNCO SAMPO SAMSUNG SAMSUX SANSEI SANSUI SANYO SCEPTRE SCOTCH SCOTT SEARS SELECO SHARP SHENG CHIA SHOGUN SIEMENS SIGNATURE SIMPSON SOLE SONY SOUNDESIGN SPECTRICON SQUAREVIEW STARLITE SSS SUPRA SUPRE MACY SUPREME SVA SYLVANIA SYNTAX OLEVIA TANDY TATUNG TECHNICS TECHNOL ACE TECHWOOD TEKNIKA TELEFUNKEN TELERENT TERA TMK TNCI TOSHIBA TOTEVISION TVS UNIVERSAL VICTOR VIDEO CONCEPTS VIDIKRON VIDTECH VIEWSONIC VIKING VIZIO WARDS WAYCON WESTINGHOUSE YAMAHA YORK YUPITERU ZENITH ZONDA

Set-Up Code Number

053 054

VCR-TV/VCR

034 058

AUX-AUDIO

074 091
ADMIRAL ADVENTURA AIKO AIWA AKAI AMERICA ACTION AMERICAN HIGH AMPRO ANAM ASHA AUDIO DYNAMICS AUDIOVOX BEAUMARK BROOKSONIC CALIX CANON CAPEHART CCE CITIZEN COLT CRAIG CURTIS MATHES CYBERNEX DAEWOO DAYTRON DBX DYNATECH ELECTROHOME ELECTROPHONIC EMERSON FISHER FUJI FUNAI GARRARD GE GO VIDEO GOLDSTAR GRADIENTE HARLEY DAVIDSON HARMAN KARDON HARWOOD HITACHI HQ INSTANTREPLAY JCL JCPENNEY JENSEN JVC KEC KENWOOD KLH KODAK LG LLOYD LOGIK LXI MAGIN MAGNAVOX MARANTZ MARTA MATSUI MATSUSHITA MEI MEMOREX MGA MGN TECHNOLOGY MINOLTA MITSUBISHI MOTOROLA MTC MULTITECH NEC NIKKO NOBLEX NORDMENDE OLYMPUS OPTIMUS OPTONICA
ORION PANASONIC PENTAX PHILCO PHILIPS PILOT PIONEER PORTLAND PROFITRONIC PROTEC PULSAR QUARTZ QUASAR RADIO SHACK RADIX RANDEX RCA REALISTIC RICO RUNCO SALORA SAMSUNG SANKY SANSUI SANYO SCOTT SEARS SHARP SHINTOM SHOGUN SIGNATURE SINGER SONY SOUNDESIGN STS SYLVANIA SYMPHONIC TANDY TATUNG TEAC TECHNICS TEKNIKA THOMAS TMK TOSHIBA TOTEVISION UNITECH VECTOR RESEARCH VICTOR VIDEO CONCEPTS VIDEOSONIC VILLAIN WARDS WESTINGHOUSE XR-1000 YAMAHA ZENITH

SEARS SONY SYLVANIA SYMPHONIC THOMAS ZENITH
SYMPHONIC TATUNG TEAC TECHNICS TECHWOOD THETA DIGITAL THOMPSON TOSHIBA URBAN CONCEPTS VENTURER X-BOX YAMAHA ZENITH
ELAN ENLIGHTENED AUDIO ESCIENT FISHER FLEXTRONICS FOSGATE AUDIONICS GE GOLDSTAR HARMAN KARDON HITACHI INTEGRA JAMO JCPENNEY JENSEN JVC KENWOOD KLH KOSS KRELL KYOCERA LEXICON LINN LUXMAN LXI MAGNAVOX MARANTZ MCINTOSH MERIDIAN MITSUBISHI MONDIAL MYRYAD NAD NAKAMICHI NEC NIRO NILES ONKYO OPTIMUS OUTLAW PANASONIC PARASOUND PHILIPS PIONEER POLKAUDIO PROCEED RCA REALISTIC ROTEL RUSSOUND SAMSUNG SANSUI SANYO SCOTT SHARP SHERWOOD SONY SOUNDESIGN SSI SUNFIRE TEAC TECHNICS THETA DIGITAL TOSHIBA YAMAHA ZENITH
ABEX ADMIRAL ADVENT ADVENTURA AIKO ALERON AKAI A MARK AMERICA ACTION AMPRO AMSTRAD ANAM AOC APEX DIGITAL AUDIOVOX BARCO BELCOR BELL&HOWELL BLAUPUNKT BRADFORD BROKSONIC BROCKWOOD CAIRN CANDLE CAPEHART CELEBRITY CENTURION CETRONIC CITIZEN CLARION CLASSIC CLP CLASSIC COLORTYME CONCIERGE CONCERTO CONTEC CORNEA CORONADO CRAIG CROSLEY CROWN CURTIS MATHES CXC DAEWOO DAYTRON DELL DIMENSIA DREAMVISION DUKANE DUMONT DURABRAND DWIN DYNASTY DYNATECH EIKI ELECTROBAND ELECTROHOME ELEKTRA EMERSON ENVISION ESA FISHER FUJITSU FUNAI
183 GIBRALTAR GOLDSTAR 143 GRUNPY HALL MARK 004 HARLEY DAVIDSON 028 HARVARD 043 HAVERMY 081 HELLO KITTY 076 HIMITSU 043 HITACHI HP 327 INFINITY 164 INFOCUS 330 INTEQ 183 INSIGNIA 350 JANEIL 002 JBL 164 JCB 070 JCPENNEY JENSEN 013 JVC 241 KAWASHO 197 KEC 043 KENWOOD KLOSS KLOSS NOVABEAM 002 KMC 143 KTV KURAZAI 072 LG LODGENET 072 LOEWE 164 LOGIK 072 LUXMAN 004 LXI 164 MAGNAVOX 226 MAJESTIC MARANTZ 184 MATSUI 164 MATSUSHITA 080 MAXENT 242 MEGATRON 163 MEMOREX 004 METZ 088 MGA 042 MIDLAND MINERVA 088 MINUTZ 008 MITSUBISHI 191 MONTGOMERY WARD MOTOROLA 081 MTC MULTITECH 043 NAD NEC 262 NET TV 202 NIKEI 043 NIKKO NTC 103 NUVISION 351 ONKING 043 ONWA 043 OPTIMUS 025 OPTONICA OPTOMA ORION 096 PANASONIC PHILCO PHILIPS 259
AIWA ALLEGRO ALPINE APEX DIGITAL BLAUPUNKT BROKSONIC CINEVISION DENON DURABRAND DVD 2000 EMERSON ENTERPRISE FISHER FUNAI GE GOLDSTAR GO VIDEO GREENHILL HARMAN KARDON HITACHI HITEKER ILO INITIAL INTEGRA JBL JVC KENWOOD KISS KLH KRELL LITEON LEXICON LG MAGNAVOX MARANTZ MALATA MERIDIAN MICROSOFT MINTEK MITSUBISHI MYRYAD NAD NAKAMICHI NESA ONKYO OPTIMUS OPPO ORION PANASONIC PHILIPS PHILIPS MAGNAVOX PIONEER POLAROID POLK AUDIO PROCEED PROSCAN RCA RIO RJTECH SAMSUNG SANSUI SANYO SEARS SENSORY SCIENCE SHARP SHINSONIC SONIC BLUE SONY SYLVANIA

DVD-DVD Recorders

GO VIDEO ILO KISS LITEON PANASONIC SENSORY SCIENCE SONY TOSHIBA

191 188

DVD-TV/DVD Combos
AIWA FUNAI SAMSUNG SYLVANIA SYMPHONIC TOSHIBA 143 130

DVD-TV/DVD/VCR Combos

MAGNAVOX PANASONIC SYLVANIA TOSHIBA 143 164

DVD-DVD/VCR Combos

GO VIDEO PANASONIC PHILIPS SAMSUNG SANSUI SONY TOSHIBA ZENITH
105 (VCR Functions for VCR 067) (VCR Functions for VCR101)
ADC ADCOM AIWA AKAI AMC ANGSTROM ANTHEM ARCAM ATLANTIC TECHNOLOGY AUDIO FILE AUDIO MATRIX AUDIO TECHNICA B&K BOSE BOSTON ACOUSTICS CARVER CINEMA SOUND CITATION CLARION DELPHI DENON

330 340

AMERICA ACTION DAEWOO EMERSON FUNAI GOLDSTAR HARLEY DAVIDSON HITACHI JCPENNEY LG LLOYD MAGNAVOX MEMOREX PANASONIC PHILIPS RADIO SHACK RCA 123 034

AUX-DVR(TIVO)

HUGHES HUMAX PHILIPS RCA REPLAY NETWORKS SONY TIVO TOSHIBA 817