VDO Cyclecomputing MC1 0
For the cyclist that likes to track climbing feet even if it's small rolling hills, it still adds up. Cycling functions include: current/average/max speed, ride time (total bike 1/bike 2/bike 1+2),Trip (total bike 1/ bike 2/ bike), 2nd programmable trip distance and stopwatch. Altimeter functions include: Current, maximum and average altitude and gradient. Current temperature, maximum altitude, total feet climbed (total bikes 1/bike 2/ bike). Also, home altitude is adjustable with a quick re... Read more
Part Number: VDMC1
[ Report abuse or wrong photo | Share your VDO Cyclecomputing MC1 0 photo ]
VDO Cyclecomputing MC1.0, size: 860 KB
VDO Cyclecomputing MC1.0+
VDO Cyclecomputing MC1 0
User reviews and opinions
No opinions have been provided. Be the first and add a new opinion/review.
INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL DINSTALLATION ET DUTILISATION MANUALE DINSTALLAZIONE E FUNZIONAMENTO INSTALACION Y OPERACIN MANUAL HANDLEIDING
P7 Press AC-Button to Begin or install battery (P6)
Press MODE 2 for next press MODE 1 to select
WS in mm / inch
ETRTO 47-305 47-406 34-540 47-507 23-571 40-559 44-559 47-559 50-559 54-559 57-559 37-590 20-571 16x1,75 20x1,75 24x1 3/8 24x1,75 26x1 26x1,5 26x1,6 26x1,75 26x1,9 26x2,00 26x2,125 26x1 3/8 26x3/4 WS in mm KMH 1954 WS in inch MPH 50,1 62,6 76,7 75,1 77,7 79,8 80,7 81,5 82,2 83,2 84,0 82,9 76,9
ETRTO 32-630 40-622 47-622 40-635 37-622 18-622 20-622 23-622 25-622 28-622 32-622 37-622 40-622 27x1 1/4 28x1,5 28x1,75 28x1 1/2 28x1 3/8 700x18C 700x20C 700x23C 700x25C 700x28C 700x32C 700x37C 700x40C
WS in mm KMH 2224
WS in inch MPH 86,6 87,6 89,3 89,2 86,8 82,8 83,2 84,0 84,5 84,6 85,6 86,8 87,6
P10 SET Metric System SET WS 1
Start at TRIP DIST Press MODE 1 for 3 sec.
Press MODE 2 to select between KMH and MPH
Press MODE 1 to set WS1
Press MODE 2 to increase
SET WS 2
Press MODE 1 to switch and MODE 2 to increase continue for all 4 digits
Press MODE sec. to end Press MODE 1 to switch Press MODE 2 to increase
Press MODE 1 to set WS2 Press MODE sec. to end without setting WS2
P11 SET Clock
Press MODE 1 3sec.to start
Press MODE 2 to switch between 24h or 12h
Press MODE 1 to set the hours
MODE 2 to increase the hours
Press MODE sec. to end
Press MODE 2 to increase the minutes
Press MODE 1 to set the minutes
Press MODE 1 to switch
Press MODEsec. to end after you set the navigator
Important: Navigator in Display
Press MODE 2 to reset
Press MODEsec. to end after you set the odometer
Press any button BIKE CHECK disappears
The service icon will remain flashing. Another 50 km/35 mi.
Then the service interval icon will also disappear
Set Home altitude
Press MODE 1 3sec.to Enter Home Altitude
Press MODE 1 to decrease privious value Hold down to quickly scroll
Press ALTI 3sec. to end
Press MODE1+MODE2 3sec. to recalibration
Press MODE 2 to increase privious value Hold down to quickly scroll
Correction of actual altitude
Press ALTI 3sec.to Enter Real Altitude
Press ALTI 3sec. to end
INSTALLATION AND OPERATION MANUAL - VDO MC 1.0 Index Preface Important information about the altimeter 1. Mounting 1.1 Handlebar holder 1.2 Speed transmitter (sender) 1.3 Spoke magnet 1.4 Twist-Click mounting of computer onto handlebarholder 1.5 Installing the battery 2. Initial set-up of your VDO MC 1.0 2.1 Basic information on how to operate your VDO MC 1.0 2.2 Interrogating information 2.3 Calling set-up mode 2.3.1 Button / key covering in set-up mode 2.4 Selecting your language 2.5 Selecting the wheel circumference (wheelsize) 2.5.1 How to determine the precise wheelsize 2.5.2 Entering (programming) the wheelsize 2.5.3 Switching wheelsizes (Changing from WS1 to WS2) 2.6 Entering time / setting the clock 2.7 The NAVIGATOR
2.7.1 Presetting the NAVIGATOR 2.7.2 Resetting the NAVIGATOR to zero 2.8 Presetting / programming the odometer 2.9 Manual operation of the stopwatch 3. Resetting information to zero 4. SERVICE INTERVAL indicator 5. SLEEP MODE 6. Altimeter information of your VDO MC 1.0 6.1 The home or basis altitude 6.1.1 Significance of the home or basis altitude 6.1.2 Calibrating the altimeter to your home altitude or basis of choice 6.1.3 Re-calibrating the altimeter to absorb changes in barometric pressure 6.2 Correction of actual altitude 7. FAQ / Troubleshooting 8. Warranty 9. Technical data 10. Packaging contents
Thank you very much for buying a VDO MC 1.0 bicycle computer featuring an altimeter. The more familiar you get with this model, the more enjoyable your trips are going to be. Hence, our urgent request: Please read thoroughly all the information provided in this manual. You are getting important and useful hints for operation to make you fully benefit from all the technical features of your VDO MC 1.0. We wish you enjoyable trips and rides on your bike with VDO CYCLE PARTS GMBH Important information about the altimeter The altitude calculation works by measuring barometric pressure. Your VDO MC 1.0 converts the data of current barometric pressure into the respective altitude. Depending on the barometric pressure (weather) different altitude readouts for the same location may be displayed. That these barometric changes do not reflect in your altitude readout, your VDO MC 1.0 features an easy-to use barometric pressure re-calibration (see chapter 6.1.3) Accurate calculation of altitude requires the precise determination of home or basis altitude. To process barometric pressure data, there is a hole drilled into the bottom of the housing of your VDO MC 1.0. This hole must never be clogged or taped over. Please do check on its cleanliness regularly and free the hole carefully if needed. You must never poke a pointed instrument into the hole.
1.Mounting 1.1 Mounting the handlebar holder The handlebar holder fits handlebars of any diameter. Before mounting the system, decide if you will be using your left or right hand to operate the computer and then mount the handlebar holder on the respective side. Position the handlebar holder, insert the strap and adjust is by tightening the screw. Warning: Before tightening the handlebar holder, make sure to adjust the position of the computer head (inclination) when the LCD-display is best visible for you. Only when you find the best position tighten the screw.
P1 1.2 Mounting the speed transmitter / sender The sensor should be mounted on the same side of the fork as the holder is on the handlebar. Make sure to position the respective rubber shim between fork and sender, position the curved back of the sender next to the spokes and make sure the sender is aimed at the receiver (computer head). Important: Do not tighten the cable ties yet. Accurately position the sensor and the spoke magnet first, then tighten the cable ties. 1.3 Mounting the spoke magnet Distance between magnet and sensor should be approx. 1-5 mm. In case this distance is not achievable in the current position, slide the sensor and the magnet on the fork or spoke accordingly. The center of the magnet must be positioned to the marking on the sender. See fig. P2+P3
1.4 Twist-Click mounting of computer on to holder
The Twist-Click mounting has been exclusively developed for the new line of VDO CYTEC computers. The VDO MC 1.0 also features the Twist-Click-System. The computerhead is put onto the handlebar and by a right turn of the computerhead (TWIST) fixed to the holder (CLICK). P4 It is just as easy to remove the computerhead from the handlebar holder. Slightly push the computerhead down, twist it to the left, remove computerhead from handlebar holder. P5 Watch out: Please remove the computerhead from the handelbar holder when you intend not to use your bike for a longer period of time. (battery power) 1.5 Installing the 3V battery (type 2032) into the computer head To save battery power, your VDO MC 1.0 comes with the battery not yet fitted. Prior to initial use the batteries will first have to be installed with the positve pole on top. Warning: Once the battery is installed your VDO MC 1.0 starts the set-up of display language (see also chapter 2.4 for details). P6 If you find the computer is not functioning properly after the battery is changed, push the AC-button (Auto Clear) on the rear side of the computer to reset. P7
2. Initial set-up of your VDO MC 1.0 2.1 Basic information on how to operate your VDO MC 1.0 Make sure you are familiar with the computers basic operating instructions before the initial set-up and use. Your VDO MC 1.0 features 3 keys / buttons Left. Center.Right MODE1.. ALTI. MODE2 The display The following information is permanentely displayed: Current / actual speed in KMH or MPH accurate to +/- 0.5 KMH / MPH Symbol (MPH or KMH) for the measuring system selected, Wheelsize selected: Bike 1 (WS1) or Bike 2 (WS2) Symbols to compare actual speed and average speed (up-arrow, down-arrow, dot) ALTI - display of current / actual altitude Current grade / inclination climbed or descended in % Current temperature in C or F
Function TRIP DIST RIDE TIME AVG SPEED STOP WATCH MAX SPEED Function NAVI GATOR CLOCK ODO 1 METER ODO 2 METER ODO TOTAL
Function TRIP ALTI MAX ALTI AVG CLIMB MAX CLIMB TOTAL ALTI TOP ELVTN
2.2 Interrogating information
With the MODE1 button you call up following information: TRIP DIST - RIDE TIME - AVG SPEED - STOP WATCH - MAX SPEED TRIP DIST trip counter for your individual trip, counting to 999.99 km or mi RIDE TIME trip timer featuring automatic start/stop function up to 19:59:59 h AVG SPEED average speed, accurate to two decimal points STOP WATCH manually operated stop watch counting up to 19:59:59 MAX SPEED maximum speed achieved during a ride up to 199.5 km/h or mph Important: If the ride timer overflows 19:59:59 h, it is automatically reset to 00:00:00. Simultaneously, your average speed counter AVG SPEED is reset to zero. If your trip counter overflows 999.99 KM or M, it is automatically reset to 000.00 Simultaneously, your average speed counter AVG SPEED and your ride timer RIDE TIME are reset to zero.
With the MODE2 button you call up following information: NAVI GATOR - CLOCK - ODO1 METER - ODO2 METER - ODO TOTAL NAVI GATOR Second, manual trip counter, can be reset to zero individually, can be preset and counting up from there on. CLOCK Time of the day in 12h or 24h mode ODO 1 METER Odometer (sum of all trips) on Bike 1, up to 99.999 km or mi. ODO 2 METER Odometer (sum of all trips) on Bike 2, up to 99.999 km or mi. ODO TOTAL Odometer (sum of all trips on both bikes), sum of Bike 1 and Bike 2, up to 199.999 km or mi. Important: Switching conversions from mi to km at odometer 62.111 mi and up leads to a reset to zero of the odometer. (62.111 mi converts to approx 100.000 km but the display only holds 99.999 km max.)
With the ALTI button you call up following information: TRIP ALTI - MAX ALTI - AVG CLIMB - MAX CLIMB - TOTAL ALTI - TOP ELVTN TRIP ALTI Indicaton of altitute gained / elevation climbed during the current trip as long as speed impulses are processed. Descended altitude is not counted. MAX ALTI Indication of highest elevation reached during the current trip. AVG CLIMB Indication of average inclination (in %) during the currrent trip. MAX CLIMB Indication of maximum inclination (in %) during the current trip. TOTAL ALTI Indication of total altitude climbed on all your trips for both wheelsizes WS1 + WS2 TOP ELVTN Indication of highest elevation reached for all your trips for both wheelsizes WS1 + WS2
2.3 Calling up set-up modes for computer / speedometer functions Other than calling up various functions and informations, the MODE 1 key calls up any set-up mode. Calling up the set-up modes requires a 3 sec pressing of the MODE 1 key. Set-up modes can be entered from various information displays: You want to set up: Wheelsize 1 or Wheelsize 2 Clock Odometer for Bike 1 Odometer for Bike 2 Navigator, second trip counter Display Information needed TRIP DIST CLOCK ODO 1 METER ODO 2 METER NAVIGATOR
2.3.1 Button / key covering in set-up mode Once you have entered a set-up mode with MODE 1, the keys have the following (different) functions. MODE 1 key: jump from digit to digit; exit set-up mode (pressing MODE 1 for 3 sec.) MODE 2 key: increase/change of digit selected; selecting display symbols
2.4 Selecting your language
After installing the battery or pressing the AC-button your VDO MC 1.0 automatically requests a display language to be selected. After installing the battery, your VDO MC 1.0 first greets you in English (by default) displaying "ENJOY YOUR MC1.0" The VDO MC 1.0 will then automatically request you to select your display language. The VDO MC 1.0 subsequently displays 7 languages: ENTER LANGUAGE, -- EINGABE SPRACHE--CHOIX LANGUE--REGOL LINGUA--ENTER TAAL--AJUST LENGUA--USTAW JEZYK. After this automatic scroll you can then select your language. I.e. "LANGUAGE ENGL" will be in display By pressing the MODE 2 key (right), the various languages will be displayed. Process: LANGUAGE ENGL -M2-SPRACHE DEUT- M2-LANGUE FRAN -M2-LINGUA ITAL- M2-TAAL NEDL -M2-LENGUA ESPAN -M2- JEZYK POLSK Once your language is displayed, press the MODE 1 key for 3 sec. Your selected language is now stored, any further information is displayed in that language. The display now shows TRIP DIST, if you have chosen English for your language.
2.5 Selecting the wheel circumference (wheelsize) Your computer VDO MC 1.0 indicates your wheel size as WS (Wheelsize) = wheel circumference. Your VDO MC 1.0 is able to process two different wheelsizes for two different bikes (i.e. road bike and mountainbike) The following default values are preset Wheelsize 1 WS1 = 2155 mm wheel circumference Wheelsize 2 WS2 = 2000 mm wheel circumference Warning: After a battery change the above defaults are automatically applied. After a battery change, you have to re-enter the precise values for your bike(s). 2.5.1 How to determine the precise wheelsize Place the front wheel of your bike with the valve at the bottom, mark this position with a line and push your bike ahead until exactly one rotation of the front wheel is completed. Draw another line where the valve now is. Take a ruler and measure the distance between marks 1 and 2 which reflects the wheelsize = wheel-circumference. The figure measured (inches or mm) is the wheelsize to be entered into your computer. see fig. If you have selected MPH readout you must enter your wheelsize in inches. Hence, altitude is displayed in ft and temperature in F. If you have selected KMH readout you must enter your wheelsize in mm. Hence, altitude is displayed in m and temperature in C. Standard wheelsizes and respective values in mm and inches are shown in chart 1 (see page..) P9 P8
2.5.2 Entering (programming) the wheelsize(s)
Step 1: Step 2:
By pressing MODE 1 call TRIP DIST in your display. Press MODE 1 for 3 sec. In the upper part of the display you see "WS1" and "KMH" or "MPH" flashing. The lower part of the display alternately shows "ENTER MTRIC SYSTM" and "KMH" or ENTER ENGL SYSTM and MPH. With MODE 2 you choose whether you want kilometers=KMH oder miles=MPH as a measuring unit. Once the conversion of KMH or MPH has been chosen, you proceed by briefly pressing (0.1 sec) MODE 1. The lower part of the display now alternates "ENTER WHEELSIZE1" and 2155. The last number "5" flashing. With MODE 1 and MODE 2 you enter your measured wheelsize 1 (bike1). MODE 2 increases the flashing number MODE 1 jumps to the next number, see set-up mode. Once you have entered the last number of wheelsize 1 and press the MODE 1 button, the computer automatically jumps to the setup mode for wheelsize 2. The lower part of the display alternately shows "ENTER WHEELSIZE2" and 2000 with the last number "0" flashing. Enter your wheelsize 2 as described in Step 5. Once you have entered wheelsize 2, press MODE 1 for 3 sec to exit set-up mode. The computer will return to displaying TRIP DIST.
Step 3: Step 4: Step 5:
Warning: Exiting setup procedure before having completely entered the precise wheelsize may lead to faulty readouts. P10
2.5.3 Switching wheelsizes (changing from WS1 to WS2) To change from wheelsize 1 to wheelsize 2 and vice versa press and hold MODE1 and MODE2 simultaneously for 3 sec. Warning: Once you have switched from wheelsize 1 to wheelsize 2 or vice versa following Tripdata of wheelsize 1 or 2 is automatically reset to zero: TRIP DIST, RIDE TIME, AVG SPEED, MAX SPEED, TRIP ALTI, AVG CLIMB, MAX ALTI, MAX CLIMB. All of these values are newly calcualted after switching the wheelsize. 2.6 Setting the clock CLK Your VDO MC 1.0 features a clock with hour and minute display in either 12 h or 24 h mode. To access the clock setup mode proceed as follows: Step 1: MODE 2 calls the CLK information into your display Step 2: Press the MODE 1 for 3 sec. The set-up mode for the clock starts. The lower part of the display alternately shows "ENTER CLOCK" and "24" and 12 Step 3: With MODE 2 you choose whether you want your time in a 24 or 12 hour mode. Step 4: With MODE 1 you start the hour setup. The hour display will be flashing and can be changed with MODE 2. Step 5: With MODE 1 you start the minute setup. The minute display will be flashing and can be changed with MODE 2. Step 6: Once hours and minutes are correctly entered, you exit CLK set-up mode by pressing MODE 1 for 3 sec. P11
2.7 The NAVIGATOR
The NAVIGATOR is a second, individual trip distance counter that can be: manually reset to zero preset to a certain value, the trip distance is then counted from this value. The NAVIGATOR is very helpful following road book instructions or tour suggestions of bike magazines. For example, your road book tour wants you "to go straight for a mile and then make a right turn, then go on for half a mile and make a sharp left turn". These instructions can be precisely followed by using the NAVIGATOR. Once you have arrived at the first intersection after the first mile, you reset the NAVIGATOR to zero and and follow the next leg for half of a mile. At the second intersection you reset to zero again and follow the next instruction of your road book. The NAVIGATOR can be preset and proceed from this individual value. For example, you are unable to start your tour at the point 0 km/m, but at 5.3 km. This value can be preset / entered into the NAVIGATOR. The NAVIGATOR will then count on from 5.3 km. Should you have made a wrong turn, return to that spot and enter your leg distance anew, continue to follow your roadbook instructions 2.7.1 Presetting the NAVIGATOR Step 1: MODE 2 calls NAVIGATOR into display Step 2: Press MODE 1 for 3 sec. The lower part of the display alternetely shows "ENTER NAVIGATOR" and "000.00" with the last digit "0" flashing. Step 3: By pressing MODE 2 you increase the flashing number, by pressing MODE 1 you jump to the next number 000.00, etc. Step 4: Once the NAVIGATOR is preset, exit setup mode by pressing MODE 1 for 3 sec. The display shows NAVIGATOR and the preset value. Your VDO MC 1.0 will be counting on from this preset value.
2.7.2 Resetting the NAVIGATOR to zero Step 1: Step 2: MODE 2 calls NAVIGATOR into display Press MODE 2 for 3 sec., the value indicated is being reset to zero. Your VDO MC 1.0 will be counting on from zero.
Warning: Before resetting to zero, make sure the information NAVIGATOR is called in. If NAVIGATOR is not in the display, you are accidentally re-setting other information to zero. 2.8 Presetting (programming) the odometer After a battery change, you can re-enter previous odometer values (for both bikes) into your VDO MC 1.0. Step 1: With MODE 2 call "ODO1 METER" or "ODO2 METER" into display, depending which one of these values you want to re-enter. Step 2: Press MODE 1 for 3 sec. The lower part of the display alternately shows "ENTER ODO1 METER" or "ENTER ODO2 METER" plus the respective value with the last number flashing. With MODE 2 you increase the number, with MODE 1 you jump to the next number etc. Once you have entered your values for ODOMETER 1 and ODOMETER 2, you exit set-up mode by pressing MODE 1 for 3 sec.
Step 3: Step 4:
2.9 Manual operation of the STOPWATCH
Your VDO MC 1.0 features a manual stopwatch in addition to the ride-timer with automatic Start/Stop function. The manual stopwatch is counting up to 19:59:59 HH:MM:SS There are two ways to call in the stopwatch and simultaneously start it: Direct Start: By pressing M1 and M2 briefly the stopwatch is called in and started simultaneously. Starting downhill a brief pressing of M1 and M2 will do to call in the stopwatch and start it at the same moment. Delayed Start: By pressing MODE1 the stopwatch is called in. By then pressing MODE1 and MODE2 briefly the stopwatch is started. With the stopwatch running you might as well call further information in your display. The stopwatch will keep running in the background. Display indication will show that the stopwatch is running. 3. Resetting information to zero By pushing MODE2 for 3 sec information / data is reset to zero. Following trip data is simultaneously reset to zero: TRIP DIST--RIDE TIME--AVG SPEED--MAX SPEED--TRIP ALTI--MAX ALTI--AVG CLIMB--MAX CLIMB Following data may be individually reset to zero, if desired so: NAVI GATOR Call NAVI GATOR information in your display. Push M2 for 3 sec to reset this data to zero. STOP WATCH Call STOP WATCH information in your display. Push M2 for 3 sec to reset this data to zero. TOTAL ALTI--TOP ELVTN--ODO TOTAL These summarizing functions (total altitude climbed / highest elevation reached Total Odometer) are especially protected to unintended erasing / resetting. These informations can only be reset by changing battery or by pressing AC-button on backside of computer.
4. Service Interval Indicator Your VDO MC 1.0 features a Service Interval Indicator to remind you to have your bike serviced at your trusted bike shop. The service interval reminder is indicated separately for both your bikes. Every 750 km / 468 mi, the service icon is activated. The service icon flashes and the lower part of the display shows "BIKE CHECK" By pressing any of the buttons, the "BIKE CHECK" information disappears. Other information can still be reviewed The flashing service icon will remain in display. After another 50 km / 35 mi, the service interval icon will also disappear. 5. Sleep-Mode Your VDO MC 1.0 features SLEEP-Mode. During SLEEP-Mode the display is shut down. The clock, and if activated, the service interval icon and/or the stopwatch icon, remain displayed. Your VDO MC 1.0 automatically goes into SLEEP-Mode after 5 min if no buttons are pressed no speed impulses are processed SLEEP-Mode is terminated if any button is pressed speed impulses are processed Watch out! As long as the computer is mounted to the handlebar-holder, the receiver for wireless transmission remains in ON-position. Take the computer off the handlebar-holder when you don't ride your bike, this will save battery power!
6. Altimeter information of your VDO MC 1.0
Your VDO MC 1.0 does permanentely display following altimeter-information: current altitude in meters of feet current incline or grade in % current temperature in C or F Important: Current incline or grade is displayed in increments of 1%. A negative grade (descent) is indicated by a negative sign. The current incline / grade information is calculated every 4 sec (display refresh) by incorporating the TRIP DIST and TRIP ALTI information of the last 12 sec. Should you have climbed AND descended during the last 12 sec due to hilly conditions, the correct indication may be delayed. Information to be called in by pushing the ALTI button TRIP ALTI--MAX ALTI--AVG CLIMB--MAX CLIMB--TOTAL ALTI--TOP ELVTN TRIP ALTI Indication of altitude climbed during the current / actual trip. Only positive changes in altitude are measured when speed impulses are processed simultaneously. Indication of the highest altitude reached during the current / actual trip. Indication of the average grade (in %) for the current / actual trip. Indication of the maximum grade (in %) for the current / actual trip. Indication of total altitude climbed during ALL previous trips. Indication of the highest elevation reached during ALL previous trips.
MAX ALTI AVG CLIMB MAX CLIMB TOTAL ALTI TOP ELVTN
6.1. The home altitude or basis altitude of choice 6.1.1. Significance of the home or basis altitude The altitude calculation works by measuring barometric pressure. Your VDO MC 1.0 converts the data of current barometric pressure into the respective altitude. In order for your VDO MC 1.0 to indicate altitude and climbing precisely, your home or basis altitude must be entered before. The current barometric pressure is allocated to the home altitude entered. Changes in barometric pressure due to weather changes require a re-calibration (= changed barometric pressure allocated to home altitude). Your VDO MC 1.0 features the easy-to-use ALTI-correction (see chapter 6.1.3). Based on this this new home altitude (=changed barometric pressure of start location) all further measurings are calculated. For your home altitude you enter the altitude of your start location (i.e. home) which can be obtained from topographical maps or inquired for at nearby airports. Changes in barometric pressure are only converted to altitude climbed when speed impulses are processed at the same time. This avoids changes in weather conditions reflect in changes of the gained altitude indication. Accurate calculation of altitude requires the precise determination of home or basis altitude. To process barometric pressure data, there is a hole drilled into the bottom of the housing of your VDO MC 1.0. This hole must never be clogged or taped over. Please do check on its cleanliness regularly and free the hole carefully if needed. You must never poke a pointed instrument into the hole.
6.1.2. Setting up / entering your home or basis altitude
Step 1: By pressing ALTI call TRIP ALTI in the display. Push MODE1 for 3 sec ENTER HOME ALTI TUDE and its previous value will be displayed. Step 2: By pressing MODE2 the previous value is increased. Hold down the button to quickly scroll. By pressing MODE1 the previous value is decreased. Hold down the button to quickly scroll. Display capacity from -300 to +6000 meters / -984 to +19685 feet. Step 3: Once you have entered your home altitude, terminate set-up by pressing ALTI for 3 sec. TRIP ALTI information will be back in display. Depending on the home altitude entered the actual altitude may read out differently. 6.1.3. Re-calibrating the altimeter to absorb changes in barometric pressure Changes in barometric pressure make your VDO MC 1.0 change the readout of the current / actual altitude. This new readout may differ from the value you have determined for your home altitude (= same location but changed barometric pressure). So before you go out for a ride, readjust the actual displayed altitude to your home altitude. The easy-to-use re-calibration feature allocates the changes in barometric pressure to the home altitude you have entered. Step 1: Get TRIP ALTI in display Step 2: Press Mode 1 for 3 sec will bring ENTER HOME ALTITUDE in Display Step 3: Press Mode1+Mode2-button for 3 sec. Automatic recalibration of actual air pressure to your home altitude setting will be done, after that the display will show TRIP ALTI again.
6.2 Correction of actual altitude While you ride, the airpressure changes due to your gain in altitude as well as due to a wether change.To correct that influence of the wether change you can also adjust the actual altitude display at your MC 1.0.Should you see a sign indicating actual altitude and should this altitude differ from the display readout at your MC 1.0, you can manually correct the actual altitude. Step 1: Get any of the ALTI-informations in display Step 2: Press the ALTI-button for 3 sec, the display will show ENTER REAL ALTITUDE and the actual value of the altitude. Step 3: MODE 1 will decrease the value , MODE 2 will increase the value. Step 4: After you have entered the corect real altitude, you leave the setting procedure by pressing ALTI-button for 3 sec. 7. Troubleshooting This chart outlines possible malfunctions, their causes and removal. malfunctions irregular LCD readout (i.e. after battery change) no speed display most likely cause computer software is not running smoothly check for proper distance between sender and magnet battery in sender is empty computerhead is incorrectly twisted onto handlebarholder no wheelsize value entered battery in computer empty temperatures below -15C (40F) dull display readout computer in sleep-mode, not activated no speed impulses processed removal solutions press AC-button at the rear of computer head to reset readjust sender and magnet check battery and replace if necessary. place computerhead on handlebar holder and twist until detent (CLICK) enter wheelsize number check battery and replace if necessary. Back in normal temperatures, display picks up working correctly. press any button to activate computer see infomation "no speed display" above
Display fades or disappears
No altitude readout No altitude climbed indication
We warranty VDO MC 1.0 (sensor, computer head and handlebar holder) to the original purchaser for five years from date of purchase against defects in material and workmanship. This does not cover the batteries and defects resulting from normal wear and tear, improper care, accidents, abuse or alteration. Please take care to retain your receipt of purchase. In case of legitimate complaints, you are entitled to receive a comparable replacement model. Due to possible model changes, your model might not be available any more. You may contact your retailer or store where you purchased your VDO MC 1.0 or send the computer directly to us: CYCLE PARTS GMBH Grosse Ahlmuehle Rohrbach / Germany In case of technical queries, call our consumer-service-hotline (German only) Phone +49-6349-990597. Technical specifications of VDO MC 1.0 are subject to change.
9. Technical data computer handlebar holder sender/transmitter batteries operating temperatures speed range trip distance counter NAVIGATOR Odometers 1 and 2 total odometer wheelsize altitude range temperature range time window for inclinometer / display refresh 10. Contents 1 computer head 1 handlebar holder with screw 1 wireless transmitter with battery 12 V, type V23GA 1 rubber shim for sensor mount 1 spoke magnet 5 cable ties 1 battery 3 V, type CR installation and operation manual
45 x 52 x 16 mm
computer sender LCD-display min 2.5 km/h
100 mm minimum -380 m / -1247 ft -19 C / -4 F min 4 sec
45 g 15 g 20 g 3V, type V, type V23GA -15 C to +80 C max 120 km/h up to 999.99 km or mi up to 999.99 km or mi up to 99,999 km or mi up to 199,999 km or mi 3999 mm maximum 6500 m / 21325 ft 60 C / 140 F max 20 sec
MC 1.0 and DATA SHEET
VDO MC 1.0 (wired)
FUNCTIONS AND FEATURES
Cycling functions 1. current speed (up to 125 km/h) 2. trip counter (up to 999,99 KM) 3. trip ride timer (up to 19:59:59 HH:MM:SS) 4. average speed (2 decimals) 5. maximum speed (up to 125 km/h) 6. clock (12 or 24 hour) 7. manual stopwatch (up to 19:59:59 HH:MM:SS) 8. Navigator second programmable trip distance counter up to 999,99 KM) 9. total odometer (up to 199.999 KM) 10. total odometer bike 1 (up to 99.999 KM) 11. total odometer bike 2 (up to 99.999 KM) 12. comparison of current and average speed 13. 2 wheel sizes (bikes) selectable Altimeter Functions 1. 2. 3. 4. 5. 6. 7. 8. 9. Actual altitude in meters or feet, permanently in display Actual temperature in C or F, permanently in display Actual climbing percentage in %, permanently in display Summary of ridden uphill altimeters (gain in altitude) on current trip Maximum altitude on current trip Average climbing percentage on current trip Maximum climbing in percent on current trip Summary of ridden uphill altimeters (gain in altitude)on all trips, separate memories for bike 1 and bike 2 Maximum ever reached altitude on all trips, separate memories for bike 1 and bike 2
10. settable home altitude 11. recalibration function (adjust airpressure to home altitude setting) 12. settable actual altitude during a trip (to adjust influence of weather-change during a trip) VDO MC 1.0+ (analogue wireless) 2030 Functions as described in model MC 1.0: analogue wireless transmission of speed transmitting distance ca. 70 cm Battery in transmitter 12 V
further features MC 1.0 and MC 1.0+: Language selection for text in display, 7 languages selectable Service-Interval-Indicator, computer shows, when bike should be given to inspection to cycle retailer. Support during set-up procedure, what-to-do-text is shown in display 3-line display with permanent display of speed, altitude, temperature, actual climbing percentage plus additional selected cycle computer or altimeterfunction. Auto/Start-Stop of all functions Automatic transfer-calculation from KM to miles and vice versa Sleep mode / battery saver, only clock in display, if not in use TWIST-CLICK-handlebar mount, easy no-tool mounting 3 button operated, button for actual cycling information, button for stored cycling information, button for altimeter information Total distance re-settable after change of battery Selectable KMH/MPH/Meter/Foot/Celsius/Fahrenheit-display
CYCLE PARTS GMBH VDO CYCLECOMPUTING Grosse Ahlmuehle Rohrbach Germany Tel. +49 (0) 6349/9635-0 Fax +49 (0) 6349/9635-20 firstname.lastname@example.org www.vdocyclecomputer.com
For the cyclist that likes to track climbing feet even if it's small rolling hills, it still adds up. Cycling functions include: current/average/max speed, ride time (total bike 1/bike 2/bike 1+2),Trip (total bike 1/ bike 2/ bike), 2nd programmable trip distance and stopwatch. Altimeter functions include: Current, maximum and average altitude and gradient. Current temperature, maximum altitude, total feet climbed (total bikes 1/bike 2/ bike). Also, home altitude is adjustable with a quick recalibration feature.
CD3000XL 12-180 Scooba Utility Review MF6530 KRC-358RG D5400 Recon Navigator 5 Saga 2 Ypt-310 DGB-900BC C-300zoom CQ-C1505N Gpsmap 4210 Mamiya ZE SB4200 Desktop DPS16 75-FO-152 252 1AL CH D-595 Zoom TH-42PZ81E 61KEY DVD-R1100 Espio 115 3302 3342 KRC-477R WA 1000 TH-42PX60B Monitor Messenger PS121 Box UPS 960BG IP5000 Pulsar PF3 CS351 LE46B620 CDX-CA850 14PT112A-78R PKG-RSE2 Inspiron 5000 DWD-F1212 WL-500G-X SIR-K190 Airwell SPH MS-1947C 53UWX10BA Watches Casio 4380 GX-200 BD-P1650 Abit BD7 TX-32LX6F Blazer 1999 VCT-1500L Laserjet 5M MIO P560 KV-28LS35B IC7-MAX3 M5 2001 Mytouch 3G HD200HJ Gr-axm225 Fast 3202 SA-HT441 DVD-2500 37PFL7403D 32LG5000 D150 Trio Navigator 42PM3MVH LM 400 CR 20 Camera YP-F2R NW-E003 42PC3D-UE C-180 HD5730 11 DSC-P51 LMV2083ST DEH-1150MP 81733 0 1 TD-6KW LN32A330j1D Navigator 20LS5RC K C AQV09nsbn CD-305 Spiderman 2 DSR-11 MC-CG381 RM2610 L1942S-PF W2600HP-BF EWF1470
manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101