Directions for use

GGL INTEGRA / GGU INTEGRA KMX 100 KMX 200 KLR 100
Read directions for use carefully before operating
VELUX, DK-2970 Hrsholm www.VELUX.com

451452-1205

Contents
Congratulations on your new VELUX product
In order to make the best use of it please read these instructions on operation and maintenance.
Timer Access code Keypad lock Rearranging order Display light Clearing remote control settings Extending the system with VELUX and io-homecontrol products Registering a new product Using additional remote controls - Copying to a remote control not yet in operation - Copying to a remote control in operation Registering products from other types of control units Copying products to other types of control units Security key Resetting the system Installation Holder for remote control Rain sensor Blinds, roller shutters etc Specifics of the window Manual operation Maintenance Further information Display symbols Glossary

30-33 34-37

Important information Getting started Initial set-up Function guide Operation Locating and operating a product - One window - More than one window Choosing positions and luminous intensity Menu functions Menu guide Navigating in the menus Changing language Definition of Room, Group and Zone Creating a Room Editing a Room Creating a Group Naming Program keys P1 and P2 - Recording a Program P1/P2 - Activating and interrupting a Program P1/P2 2

6-7 8-9

10-11-12 13
38-39 40-43 40-41 42-43 44-45 46-47 48-49 50-51
18-19 20-21 22-23 24-25 26-29 26-27 28-29

56-57 58-59

60 61-62 3

Important information

Please keep instructions for future reference and hand them over to any new user. Safety Before operating ensure that the window with electrical products can be and is operated without risk of damage to property or injury to people or animals. For personal safety, never have your hand or body out of the window without switching off the power. Children must not be allowed to play with the window and its electrical products, and the remote control should be kept out of reach of children. If repair or adjustment work is needed, disconnect from mains supply and ensure that it cannot be reconnected unintentionally. The plug on the mains cable is for indoor use only. It is recommended to place a remote control in the room where the window and its electrical products have been installed. Function If the rain sensor gets wet, the window operator automatically closes the window; however, the ventilation flap remains open. To prevent the window from closing because of very fine/weak rain, fog or dew, the rain sensor is equipped with a heating element to keep the surface dry. If the window has been opened manually, the window operator will not be activated via the rain sensor. From fully open, it will take up to one minute before the window is completely closed. Therefore, in case of sudden rain, water may enter the room before the window is closed. In case of snow and/or ice, the operation of the window may be blocked. 4 Product This product has been designed for use with genuine VELUX products. Connection to other products may cause damage or malfunction. The product is compatible with products with the io-homecontrol logo. Electrical products must be disposed of in conformity with national regulations for electronic waste and not with usual household waste. Used batteries have to be disposed of in conformity with the relevant environmental regulations. Expected battery lifetime: Approx. 1 year. The packaging can be disposed of with usual household waste. Radio frequency band: 868 MHz. Noise level: Max 70 dB(A). Maintenance and service Disconnect from mains supply before carrying out any maintenance (including cleaning of pane) or service work to the window and products connected to it and ensure that it cannot be reconnected unintentionally during this time. If mains cable is damaged, it must be replaced by qualified personnel in accordance with national regulations. Spare parts are available through VELUX. Please provide information from data plates. If you have any technical questions, please contact VELUX.
io-homecontrol provides advanced and secure radio technology that is easy to install. io-homecontrol labelled products communicate with each other, improving comfort, security and energy savings. www.io-homecontrol.com

Initial set-up

The initial set-up must be completed within 10 minutes so please read items 1-8 before proceeding. IMPORTANT! In case of one remote control only, all products must be registered in this remote control. In case of more than one remote control, all products must be registered in one of the remote controls. Then the information must be copied from this remote control to the other remote controls, see section Using additional remote controls. Within 10 minutes of inserting the batteries, you must choose your language and prepare automatic registration of relevant electrical products in the remote control. If this time limit is exceeded, you must start afresh. When the initial set-up has been completed, all windows with electrical products connected will appear in the display.

Window Roller shutter Blind Lights

Enter Back

------------- BLIND -------------

No. 1 No. 2 No. 3

3 Press
to highlight blind "No. 3". "Enter". to start operation.

Menu guide

Guide to the menu functions of the remote control. Additional information about the individual function is provided in the relevant section.
Navigating through the menus
The example shows how to find the menu item Room by means of menu choices.

"Menu".

P1 --- Menu ---
2 Displays a list of menu items under Menu.
Press Press to highlight "Settings". "Enter" to confirm your choice.
Keypad lock Timer Settings

P1 --- Settings ---

--- Set-up of House ---
Room Group Rearrange order Rename Clear
p. 18-21 p. 22-23 p. 34-35 p. 24-25 p. 37
3 Displays a list of menu items under Settings.
Press Press to highlight "Set-up of House". "Enter" to confirm your choice.
Set-up of House User settings System settings

--- Menu ---

p. 33 p. 30-31

--- Settings ---

4 Displays a list of menu items under Set-up of
House. Press to highlight "Room". "Enter" to confirm your choice. Press You can now proceed with the menu functions under menu item Room. This way of choosing menu items is shown as follows in the rest of the instructions:

--- User settings ---

Language Programs P1/P2 Display light Access code
p. 16 p. 26-29 p. 36 p. 32
Room Group Rearrange order Rename

--- System settings ---

Register product Copy system Security key Configure
p. 38-39 p. 40-43 p. 48-49 p. 46-47
1 Press "Menu". 2 Scroll through the menus:

Settings

Set-up of House

Changing language

You can change the display text language. The example shows how to change it.
Definition of Room, Group and Zone
To make it easier to operate especially large systems it is recommended to link each product to a Room and/or a Group.

Room 1 Room 2

Definition of Room A Room consists of one or more products of any type located in the same physical room, eg bedroom or kitchen. A product can be assigned to one Room only.
2 Scroll through the menus:

User settings

Language

Definition of Group

3 The display shows a list of languages. The current
language has been ticked.
A Group consists of at least two products of the same type (eg two roller shutters). For every product type, a Group All is automatically created. Each Group All consists of all products of the same type in the House list or in the Room in question. Groups created across more Rooms are called Zones.

Press a new language. 4 Press p to highlightto confirm your choice. "Enter"
Definition of Zone A Group created across more Rooms.

--- INFORMATION ---

The display shows that the change has been saved.

Kitchen Saved

Creating a Room
If you have many products, you can collate them in Rooms to make these easier to find and operate. When creating a Room, you have to create at least two Rooms. Room 2 may consist of all the products not assigned to Room 1, see item 8.
5 Displays the product chosen.
Press "More" to move additional products to Room 1. You will return to the list in item 4. Repeat items 4-5 until these products have been moved to Room 1. "Continue" to proceed. Press
HOUSE --------- WINDOW ---------

More Continue

The example shows two rooms with two windows in each. Below it is shown how to create Room 1 by moving the relevant products from House to Room 1.
6 Displays a list of options.

--- CONTINUE ---

to highlight "Save new Room". "Enter" to confirm your choice.
Save new Room Undo product Undo new Room
(Highlight one of the other options to undo your choice).

-- INFORMATION --

7 The display shows that a new Room has been

created.

Room Create

--- PRODUCT FROM ---

Room created
8 The display asks whether you want the remaining
3 Displays the areas in House.
Press to highlight the area with the product to be assigned to Room 1 first. Press "Enter" to confirm your choice.
products to be assigned to the next Room automatically. "Yes" to save the remaining products a) Press in Room 2. "No" to return automatically to the list b) Press in item 3.
Save all remaining products in next Room

Yes No

4 Displays a list of all products in House. The prod-
uct type appears second from the top line in the display. The individual products can be identified by pressing for a short period of time. to highlight the product to be moved to Press Room 1. Press "Enter" to confirm your choice.
9 The display shows that a new Room has been
created. Note: The products are automatically renumbered when assigned to a Room.

Room 1

Room 2

Editing a Room

You can edit the Rooms you have created, ie one or more products can be moved from one Room to another. The example shows how the window operator in window No. 1 can be moved from Room 1 to Room 2.

in Room 1.

to highlight the Room in which Group 1 Press is to be created. Press "Enter" to confirm your choice.
Note: When operating Groups a delayed execution of commands might occur. If you want a particular product to respond at once, this product must be operated individually.

Group 1

Naming
You can change the names of House, Rooms, Zones, Groups, products and Programs displayed into more personal names. The example shows how to change Room 1 into Kitchen. Note: When having used the function Rename, the products are not automatically renumbered any longer.

Room 1 --- RENAME ---

6 Enter the new name using the list of characters.
Press Press to highlight the character required. "Enter" after each character.

--- RENAME --Save

KITC HEN
7 Save the new name by choosing
menus: 2 Scroll through theSet-up of House Settings
in the list when the last character has been entered. "Enter". Press

CDEFGHI

Rename
--- INFORMATION ----- RENAME ---
Displays a list of House, Rooms, Zones, Groups, products and Programs. to highlight "Room". Press "Enter" confirm your choice. Press

Room Zone Group Product

8 The display shows that the new name has been

saved.

--- AREA ---
4 Displays a list of the names automatically given to
the Rooms. to highlight "Room 1". Press Press "Enter" to confirm your choice.

--- RENAME ---

Room 1 A
5 Displays a list of characters including the save
function , the delete function character.

ABCDEFGHI

and the space
Recording a Program P1/P2
The program keys P1 and P2 can be used for pre-setting a series of operating sequences that can be activated by a single key pressure. You can record up to eight programs; four under each of the program keys P1 and P2. The programs can contain commands about operating the products and activating the timer function. The example shows how to program a window and a roller shutter to close/run down by pressing the program key P1 just once.

-- RECORD PROGRAM --

Start recording by pressing Enter. Stop recording by pressing P1 or P2

4 Press

"Enter" to start recording.
5 The display shows the latest operated product.
Icon 1. Locate the window and close it (see sections Locating and operating a product and Choosing positions and luminous intensity).

indicates that the recording is in progress.
IMPORTANT! Choose a position by pressing and holding key until the desired position has been reached. Do not use the stop key.
2. Locate the roller shutter and roll it down. 3. Press P1 "P1" when the roller shutter has rolled down.

Menu P1

User settings Programs P1/P2

--- PROGRAMS P1/P2 ---

--- PROGRAM (P1) ---
Record Program Delete Program
to highlight "Record Program". "Enter" to confirm your choice.
6 The display asks whether to save the new program.
Press "Yes" to save the new program.

Save new Program

Activating and interrupting a Program P1/P2
Activating a program You can activate eight programs at a time. You can still use the various functions of the remote control at the same time as one or more programs are activated by pressing a program key. Below four programs have been recorded under program key P1. The example shows how to activate Program 3 under program key P1.
Interrupting a program Icon indicates that a program has been activated. A program in progress can be interrupted as follows:
to find the program in progress.
"P1" three times to activate Program 3.
The activated program has been ticked. Press to highlight the program in question. "Stop" to interrupt the program. Press
Program 1 Program 2 Program 3 Program 4

--- PROGRAM P1 ---

Program 3 is marked in the display and the program automatically starts. Note: Maximum time interval between each key pressure: 2 seconds. Otherwise the program that happens to be highlighted will automatically be activated.
With the timer you can for example close a window, roll down a sunscreening product or turn off frame lights after a pre-set time interval. The example shows how to set window No. 1 in Room 1 to close after 1 hour and 10 minutes.

House -- SET TIMER --

Press to set the desired start position of the window when activated via the timer. 100% corresponds to fully open. "Enter" to confirm the setting. Press

Start position 100%

P1 --- SET TIMER ---

--- MENU ---

to set the stop position of the window Press when deactivated via the timer. 0% corresponds to fully closed. Press "Enter" to confirm the setting.

Stop position 0%

--- SET TIMER --Back

2 Press

to highlight "Timer". Enter to confirm your choice.

Time period 00 h 10 min

-- TIMER --
Press to choose the time period required. First choose minutes. Press "Enter" to change to hours.

Set timer Delete timer

to highlight "Set timer". "Enter" to confirm your choice.

Time period 01 h 10min

to choose hours. The window is now set Press to close after 1 hour and 10 minutes. Press "Enter" to confirm the setting. The display shows that the timer has been activated. Window No. 1 in Room 1 now closes after 1 hour and 10 minutes. Note: The timer can be interrupted by choosing "Delete timer" in item 3.
Locate the window, see section Locating and operating a product. The display shows the relevant product. The individual products can be identified by pressing for a short period of time. "Enter" to proceed. Press

Room 1 --- WINDOW ---

Access code
You can choose a personal access code to protect the settings under the menu item Settings. The access code must consist of four digits from 0 to 9.

Keypad lock

The keypad can be locked so that products cannot be operated without unlocking the keypad. The stop key can still be used.

Locate Menu

P1 --- MENU ---
2 Scroll through the menus: Settings User settings 3 Press

--- ACCESS CODE ---

Choose/Change Delete
to highlight "Choose/Change". "Enter" to confirm your choice.
to highlight "Keypad lock". "Enter" to confirm your choice.

- ACCESS CODE -

--- KEYPAD LOCK ---
to choose the first digit. Press "Enter" to go to the next digit. "Enter" when the last digit has been Press chosen.

Enter code 1 * * *

to highlight "Enable". "Enter" to confirm your choice. Press The keypad lock is immediately activated.

Enable Disable

Confirm code 3 4

Save Back

Unlocking keypad if the keypad has been locked: Message as shown. "Menu". Press "Locate". Press The keypad has temporarily been unlocked. The keypad will automatically be locked again 10 seconds after it has been used. Note: The keypad lock can be deactivated by choosing "Disable" in item 3. 33

to highlight "Display light". "Enter" to confirm your choice.
3 Displays a list of menu items.
Group Rearrange order Rename Clear
to highlight "Clear". "Enter" to confirm your choice.

--- DISPLAY LIGHT ---

On Off
to highlight "Off". to confirm your choice.
4 The display asks whether you want to clear all

--- CLEAR ---

Groups, Rooms, Zones, Programs and personal names you might have created. "Yes" to confirm your choice. Press Press "No" to return to item 3.
Clear all Groups/ Rooms/Zones/ Programs/Names
Note: The light in the display can be turned on by choosing "On" in item 4. 36
The remote control settings are cleared. 37
Registering a new product
When a new product has been installed, it can be registered in a remote control already in operation. This new product can be a new INTEGRA roof window, a blind, a roller shutter etc. The example shows how to register a new roller shutter in the remote control and place it in Room 1. The registration must be completed within 10 minutes, so please read items 1-9 before proceeding.
6 The display shows that the new product has been
registered. Now the product must be placed.

New products registered

7a If no Rooms have been created, the product is
automatically placed in House. Operation can start.

No. 1 Roller shutter

1 Switch on mains power to the window with electri-
7b If Rooms have been created, the product has to
cal products. If this has already been done, switch power off and then back on again.
be placed in the appropriate Room. The display shows a list of new products. In case of more new products, the individual products can be identified by pressing for a short period of time. Press to highlight the product to be placed. Press "Enter" to confirm your choice.
New products --- ROLLER SHUTTER ---

No. 1 new

menus: 3 Scroll through the System settings Settings
--- PLACE IN ----- SYSTEM SETTINGS ---
to highlight "Register product". "Enter" to confirm your choice.
Displays a list of the Rooms created. Press to highlight the Room in which the product is to be placed. Press "Enter" to confirm your choice.

Room 1 Room 2 New Room

P2 --- INFORMATION ---

--- AUTO SET-UP ---

9 The display shows that the Room has been modified. Operation can start.

Room modified

Automatic registration is running.
Copying to a remote control not yet in operation
If you have additional two-way VELUX remote controls (marked with the symbol ) or other types of two-way io-homecontrol control units, you can copy the settings from one remote control to another.

Step 2: Remote control B

4 Insert the three batteries supplied (type AA,
1.5 volt) into the remote control as shown.
The example shows how to copy from a VELUX remote control A to a VELUX remote control B not yet in operation. Note: When copying from a VELUX remote control to another type of io-homecontrol control unit, only the products registered will be copied, not the remaining settings. Step 2 must be completed within 2 minutes after implementing step 1, so please read steps 1-2 before proceeding.

5 Choose language:

Step 1: Remote control A
Press "Ready" to start automatic registration of each product. Please disregard the indication of time in the display.
"Menu". The display now indicates that copying is in progress.

--- SYSTEM SETTINGS ---

System settings
Note: Program functions P1/P2 cannot be copied.
to highlight "Copy system". "Enter" to confirm your choice.
Step 2 must now be completed within 2 minutes. 40 41
Copying to a remote control in operation
If you have additional two-way VELUX remote ) or other controls (marked with the symbol types of two-way io-homecontrol control units, you can copy the settings from one remote control to another. The example shows how to copy from a VELUX remote control A to a VELUX remote control B already in operation.
Step 3: Remote control B Reset remote control B, see section Resetting the system, step 2.
Step 4: Remote controls A and B
Note: When copying from a VELUX remote control to another type of io-homecontrol control unit, only the products registered will be copied, not the remaining settings. The copying takes place in 4 steps. Please read carefully first as it is important to execute them in the order stated.
Copy remote control A to B, see section Copy to a remote control not yet in operation. Now both remote controls will be able to operate all products in the system.
Step 1: Remote controls A and B Change the security key in both remote controls so that they have the same common key, see section Security key. Step 2: Remote control A Register all products in remote control A, see section Registering a new product, items 2-7a (or items 2-9). All products operated by remote control B will automatically be registered in remote control A.

Registering products from other types of control units
The remote control can also operate products registered in another type of VELUX or io-homecontrol control unit if they are transferred to the remote control. The example shows how to register products from from a one-way VELUX remote control B in a twoway VELUX remote control A. Steps 1 and 2 must be completed within 10 minutes, so please read items 1-6 before proceeding. Step 2: Remote control A

- SYSTEM SETTINGS-

Press Step 1: Control unit B

- AUTO SET-UP -

Set the control unit into configuration mode by pressing the RESET button at the back for at least 5 seconds.
5 Automatic registration is running.
6 The display shows that the new product(s) has/
have been registered. Now the product(s) must be placed. Please refer to the instructions in section Registering a new product, item 7a and onwards. Note: For other types of io-homecontrol control units, please refer to the instructions provided with the product in question to execute step 1. 44
Copying products to other types of control units
You can copy one or more products registered in the remote control to another type of VELUX or io-homecontrol control unit. This other type of control unit can thus operate both its own and the copied products. The example shows how to copy a roller shutter from a two-way VELUX remote control A to a oneway VELUX remote control B. Note: A one-way VELUX remote control can operate products of the same type only, eg roller shutters. Steps 1 and 2 must be completed within 10 minutes, so please read items 1-8 before proceeding.
Choose products to be configured
"Enter" to choose the product(s) to be copied to another type of control unit (B).
5 Locate the product, see section Locating and

operating a product.

No. 3 Roller shutter
6 Displays the relevant product.
"Enter" to confirm your choice.
7 The display shows that the product is ready for
Product ready for configuration
being copied to another type of control unit (B).

Step 2: Control unit B

8 Press the RESET button at the back briefly (max

--- SYSTEM SETTINGS --

5 seconds) to register the new product. The product chosen can now be operated by control unit B.

Press 46

to highlight "Configure". "Enter" to confirm your choice.
Note: For other types of io-homecontrol control units, please refer to the instructions provided with the product in question to execute step 2. 47

Security key

Each remote control has an individual security key ensuring that external control units cannot communicate with your system. The example shows how to change the security key in remote control A and in the products registered in A (step 1). If you have more than one remote control, the new security key must also be transferred to these (step 2). Step 2: Remote control B (and other)

House House

1 Press 2 3
Scroll through the menus:
Settings System settings Security key

--- SECURITY KEY ---

Change Receive
Press to highlight "Change". Press "Enter" to confirm your choice. The display now indicates that the security key has been changed.
to highlight "Receive". Press "Enter" to confirm your choice. The display indicates that the security key is being transferred from remote control A to remote control B.
4 The display asksiswhether the security key of other remote controls to be changed.
Press "No" to finish if this is the only remote control being changed. Press "Yes" if there are other remote controls. Execute step 2 for these. 48

-- CHANGE --

Change security key in another remote control

Resetting the system

The whole system, ie remote control and window with electrical products, can be reset to its initial state. To reinstate the connection between remote control and window after reset, please refer to the instructions in section Initial set-up. Resetting the system is carried out in two steps (steps 1 and 2). Step 2: Remote control
1 Slide o the battery cover as shown. 2 Press and hold the button on the right side of the
remote control with a pointed object for at least 5 seconds.

Step 1: Window

1 Open the window manually. 3 Replace the battery cover. 2 Press the test button on the window operator for
at least 5 seconds. The window and its electrical products run briey back and forth.
"Yes" to confirm that you want to reset the remote control.
The remote control will be reset. Continue?
3 Disconnect mains supply when all products have
stopped moving. Proceed with step 2. 50 The system has now been reset. To reinstate the connection between remote control and window, please refer to the instructions in section Initial set-up. 51
Fitting of holder for remote control
The remote control is provided with a wall-mounted holder, which can be fitted anywhere in your home. Note: Check that the remote control can operate the relevant products from the proposed position before it is fastened to the holder. If required, the remote control can be fastened with screws to the holder.
1 Fit the back section to the wall with the two screws

Closing window in case of power failure The chain can be disengaged by pressing the release clip on the ventilation ap bracket (D). Fold the chain as shown, and close the window (E). When the power is reconnected, the chain can be reengaged by opening the window manually and running the chain back into the window operator. Closing window if the remote control has been mislaid The chain can be disengaged by pressing the release clip on the ventilation ap bracket (D) and run back by pressing the test button on the window operator (F).
Maintenance of the window
Switch o the mains supply before proceeding with items 2, 3 and 5!
5 Cleaning the rain sensor
Dirt on the rain sensor may cause operating problems. Therefore, it is recommended to clean the rain sensor with a soft wet cloth once or twice a year or when needed.
1 Minimising condensation
Particularly in rooms with high levels of humidity, condensation can form on the inner pane of the window. This can be minimised by tting a radiator directly below the window and by airing the room frequently.
6 Maintenance of timber (GGL)

2 Cleaning the air lter

The air lter can be removed and washed with ordinary household cleaners. Fully rotate and lock the window, then remove the lter from the lter rail. (New lters are available from VELUX).

3 Cleaning the ashing

Leaves and other debris should be removed from the ashing around the window once per year to allow rainwater to ow freely.
Pre-varnished (TOPnish) and painted windows (PAINTnish) The timber has received basic treatment and a nished coating at the factory and can be cleaned with ordinary household cleaners. It must receive further treatment at least every four years and whenever required. Windows exposed to strong heat, strong sunlight and/or high levels of humidity (eg in kitchens or bathrooms) must however receive treatment at least every two years. Surface maintenance: Remove surface treatment (varnish or paint). Ensure surface is clean and dry and apply primer to the timber. When dry, apply a coat of waterbased acrylic varnish/paint (always follow the manufacturers directions). Apply the same method to the aected areas if the varnish/paint is damaged.

4 Snow and ice

Remove snow and ice to allow melt water to drain o from and around the window.
7 Cleaning the window (GGU)

The white polyurethane surface can be cleaned with ordinary household cleaners. 59

Display symbols

Batteries must be changed within 2 weeks (type AA, 1.5 volt). Timer function has been activated for the product in question. Timer function has been activated for one of the products in the remote control. Automatic registration of product(s) is running. Operation of a product. The product or function requested is highlighted. A Program (P1/P2) has been activated. A Program (P1/P2) is being recorded. Slats of Venetian blinds can be tilted from 0 to 100%. A Venetian blind can be drawn up or down from 0 to 100%. A name can be saved, see section Naming. Deletion of character, see section Naming. Space character, see section Naming. 60

Glossary

Adjustment: VELUX electrical decoration and sunscreening products are not adjusted to the window size on delivery. When operated the first time, they will therefore run from bottom to top or from top to bottom of the window without interruption. After adjustment the product is ready for use. Battery level low: The battery is running out of power. Blocked: Unknown object obstructs operation of product. Remove obstruction to obtain normal operation. Defect during operation: The product has stopped during operation. Check the product. Limited by rain sensor: It is raining and the rain sensor has been activated. Manual operation of the window is possible. Manual operation: The window has been opened manually. Close the window to allow for electrical operation. Memory: The following functions occupy the memory of the remote control: Timer, Room, Group, Rename, Programs P1/P2. Use of these functions will reduce the total memory. One-way remote control: Product based on one-way RF communication and marked with the symbol. This symbol can be found under the battery cover.
Power usage high: The power usage in the light module is too high. The light bulbs are too strong compared to the specifications or the light module is defective.
Power usage low: The power usage in the light module is too low. The light bulbs are either too weak compared to the specifications or one or more bulbs are defective. The light module might be defective. Product: A VELUX or io-homecontrol product, which can be operated via the remote control such as an INTEGRA roof window, a roller shutter, a light module etc. Reduced power supply: The power supply to the product has been reduced. Limited operation. Repeater: A unit increasing the range of the remote control. SCD (Secured Configuration Device): A security device may be integrated in the system. If installed, the security device must be activated to be able to use the functions under menu item System settings. In addition, the configuration button on the product (test button on window operator) will not work. For further information regarding SCD usage, please contact VELUX. Two-way remote control: Product based on two-way RF communication and marked with the symbol. This symbol can be found under the battery cover.

Trade catalogue

Price list (excludes VAT) June 2007 GB

VELUX because.

Highest quality standards
VELUX is the world market leader in roof windows due to our never-ending commitment to the highest quality standards. All our roof windows are laboratory tested to simulate the worst of weather conditions, and in over 40 countries VELUX products have been proven to withstand the test of time, year after year. We recognise there is no such thing as nearly watertight.
More business opportunities
The huge VELUX range of products provides you with protable business opportunities to add daylight and fresh air and increase space and value to customers homes. With VELUX you have the opportunity to impress your clients by creating stunning loft spaces and extensions, with products from the versatile centre-pivot right through to INTEGRA electric roof windows, unique Cabrio balcony and now Sun tunnels.

Easy installation

VELUX products save you time and time is money. All our products are easy and straightforward to install and combine together, especially with the patented corner bracket. Also available are a range of products designed to make the installation quicker and easier such as insulation collars, underfelt collars and vapour barriers.

Customer support

Highest quality customer support is provided by our experienced team to answer any technical queries. Extensive training is available to merchant staff and installers through the VELUX Academy. All products are supported with comprehensive guarantees 10 years for all roof windows and 3 years for all electrical components.

Peace of mind

For over 60 years we have been manufacturing and continuously improving our roof windows, designing and engineering products that are widely available, reliable and durable with the highest quality nish whilst offering real value for money. You and your customers know you can trust VELUX every time.

Electric windows

Flat roof windows

www.velux.co.uk

White nish
Selecting the most suitable solutions
Centre-pivot roof windows GGL pine nish GGU white polyurethane nish INTEGRA electric roof windows GGL pine or GGU white polyurethane nish Top-hung roof windows GPL pine nish GPU white polyurethane nish GHL pine nish CABRIO balcony Vertical elements Roof terrace Sun tunnels Conservation Conservation roof windows Conservation rooights Flat roof windows Smoke ventilation system Installing roof windows Installation products Flashings Combi-ashings Online installation information Blinds and accessories 4 4

Roof terrace

Sun tunnels
Glazing options Replacement panes Replacement ashings
Centre-pivot roof windows

GGL pine nish

Centre-pivot roof windows offer excellent quality, versatility and value for money. Made of pine with triple coat nish. Top control bar allows easy opening and also background ventilation even with window securely closed. Rotates 180 for easy cleaning of outer pane.
External frame size (nominal w x h) cm

55 x 78

55 x 98

66 x 118

78 x 98

78 x 118

78 x 140

94 x 160

114 x 118

134 x 98

Centre-pivot roof windows with pine nish

U-Value

Delivery
Flashings required. GGL 3059 GGL 3073 GGL 3060 Toughened outer pane. 1.4 W/m2K 2 Days 121.00 130.00 161.00 149.00 199.00 171.00 221.00 186.00 244.00 225.00 298.00 206.00 272.00 333.00 206.00 282.00 433.00 Toughened outer pane with laminated inner pane for additional safety. 1.4 W/m2K 2 Days 158.00 174.00 208.00
Improved U-value, toughened outer pane with clean and clear coating and laminated inner pane for additional safety. 1.3 W/m2K 7 Days 198.00 213.00 253.00 245.00 268.00 291.00 366.00
GGU white polyurethane nish
Smooth, rounded edges give a contemporary, stylish look. Moisture resistant ideal for bathrooms and kitchens. Timber core with moulded polyurethane. Two coats of white polyurethane lacquer nish. Easy to wipe clean. Top control bar allows easy opening and also background ventilation even with window securely closed. Rotates 180 for easy cleaning of outer pane.
Reduced price on white nish
Centre-pivot roof windows with white polyurethane nish

Flashings required. GGU 0059 GGU 0034 GGU 0073 Toughened outer pane. 1.4 W/m2K 2 Days Obscure glazing, toughened outer pane. 1.4 W/m2K 2 Days 154.00 162.00 161.00 164.00 191.00 191.00 185.00 185.00 234.00 201.00 203.00 256.00 225.00 224.00 289.00 250.00 247.00 321.00
Toughened outer pane with laminated inner pane for additional safety. 1.4 W/m2K 2 Days 191.00 203.00 241.00

Available on request.

Delivery time is in working days from receipt of order at VELUX for orders placed before 4pm.
INTEGRA electric roof windows
Operate every roof window, blind, shutter and awning in the building electronically from any room in the house, using a sleek, hand-held remote unit. Available in a choice of natural GGL pine or GGU white polyurethane nish. Ideal when you cant reach the window to open it. Uses radio frequency technology that works through walls from any room. Easy to order and install, comes with pre-installed hidden motor, just plug into a power supply. Fully programmable remote opens and closes individual or groups of roof windows, blinds, awnings and roller shutters. New 7 day clock and calendar for real time programming. Digital display provides constant status of io-homecontrol products Rain sensor closes window automatically in the event of rain. 10-year guarantee for the window and panes, 3-year guarantee for electrical items.
io-homecontrol provides advanced and secure radio technology that is easy to install. io-homecontrol labelled products communicate with each other, improving comfort, security and energy savings. www.io-homecontrol.com

55 x 78 U-Value

GGL 307321U GGU 007321U
Windows come complete with pre-installed motor, remote control, rain sensor, cabling and plug. Flashings required. Pine nish, centre-pivot, toughened outer pane with laminated inner pane for additional safety. 1.4 W/m2K 2 Days 396.00 404.00 435.00 443.00 447.00 469.00 540.00 516.00 547.00 525.00
White polyurethane nish, centre-pivot, toughened outer pane with laminated inner pane for additional safety. 1.4 W/m2K 7 Days 409.00 418.00 442.00 452.00 458.00 476.00

Accessories

KMX 100 KMX 200 KRA 100 KLF 100 KLB 100
Conversion kit to upgrade to full INTEGRA functionality of manual or electrically operated GGL or GGU centre-pivot roof windows installed after April 1986. 2 Days 291.00 Conversion kit allows upgrade to full INTEGRA functionality of GPL/ GPU/ GHL top-hung roof windows. 7 Days Frame lights (1 set per window. Each set consists of 2 lights). 7 Days Interface for connection to external commands or to use as a relay station to increase range. 7 Days Battery back-up (1 per window). 7 Days 291.00 50.00 104.00 95.00

Top-hung roof windows

GPL pine nish
Top-hung roof windows provide an uninterrupted view and extra feeling of space when opened. Powerful yet gentle springs make it easy to open. Bottom handle for convenient opening. Sash opens up to 45. Rotates 180 for easy cleaning of outer pane. Top control bar allows background ventilation even with window securely closed. Made of pine with triple coat nish.
*Can be used for emergency escape requirements.
For roof pitches from 55-75, please specify special springs when ordering.
Top-hung roof windows with pine nish
Flashings required. GPL 3059 GPL 3073 KMX 200 Toughened outer pane. 1.4 W/m2K 2 Days Toughened outer pane with laminated inner pane for additional safety. 1.4 W/m2K 2 Days Conversion kit for full INTEGRA electrical operation of top-hung windows. 7 Days
269.00 293.00 312.00 339.00

405.00 473.00

368.00 453.00 291.00
GPU white polyurethane nish
Stylish white nish with rounded corners for contemporary look. Timber core with moulded polyurethane. Two coats of white polyurethane lacquer nish. Easy to wipe clean. Powerful yet gentle springs make it easy to open. Bottom handle for convenient opening. Top control bar allows background ventilation even with window securely closed. Sash opens up to 45. Rotates 180 for easy cleaning of outer pane.
* Can be used for emergency escape requirements.
Top-hung roof windows with white polyurethane nish
Flashings required. GPU 0059 GPU 0034 GPU 0073 KMX 200 Toughened outer pane. 1.4 W/m2K 2 Days Obscure glazing, toughened outer pane. 1.4 W/m2K 7 Days 258.00 252.00 272.00 261.00 332.00 293.00 287.00 362.00 314.00 307.00 410.00 291.00
Toughened outer pane with laminated inner pane for additional safety. 1.4 W/m2K 7 Days 320.00 Conversion kit for full INTEGRA electrical operation of top-hung windows. 7 Days

GHL pine nish

Perfectly suited to shallower pitched roofs. Powerful yet gentle springs make it easy to open. Opens to three set positions: 5, 15and 30. Bottom handle for convenient opening. Top control bar allows background ventilation even with window securely closed. Rotates 180 for easy cleaning of outer pane. Made of pine with triple coat nish.
Flashings required. GHL 3059 GHL 3073 KMX 200 Toughened outer pane. 1.4 W/m2K 2 Days 188.00 215.00 207.00 250.00 228.00 272.00 245.00 306.00 262.00 330.00 291.00 Toughened outer pane with laminated inner pane for additional safety. 1.4 W/m2K 2 Days 225.00 260.00 Conversion kit for full INTEGRA electrical operation of top-hung windows. 7 Days

CABRIO balcony

An instant balcony from a roof window. The upper section is top-hung and opens outwards whilst the bottom section unfolds into a glazed balcony with side railing. Can be linked to other top-hung and xed roof windows to increase the amount of daylight, view and ventilation. Top-hung section rotates 180 for easy cleaning of outer pane. Made of pine with triple coat nish.

53o 35o

100 mm gap

100mm gaps

94 x 252 U-Value

198 x 252

302 x 252
Packages include: Single Cabrio pine roof window with one or two side units (GPL top-hung and GIL xed element), toughened outer pane with laminated inner pane for additional safety and suitable ashings. GDL SDOL1 GDL SDOW1 Cabrio + ashings for slate up to 8mm thick. Cabrio + ashings for tiles up to 120mm in prole. 1.5 W/m2K 1.5 W/m K 1.5 W/m2K 1.5 W/m K 1.5 W/m2K
2 Days 2 Days 2 Days 2 Days 2 Days 2 Days
1,689.00 1,705.00 2,521.00 2,552.00 3,338.00 3,378.00
GDL SKOL221 Cabrio + 1 x GPL & 1 x GIL. Flashings for slate up to 8mm thick. GDL SKOW222 Cabrio + 1 x GPL & 1 x GIL. Flashings for tiles up to 120mm thick. GDL SKOL321 Cabrio + 2 x GPL & 2x GIL. Flashings for slate up to 8mm thick.
GDL SKOW321 Cabrio + 2 x GPL & 2 x GIL. Flashings for tiles up to 120mm thick. 1.5 W/m K
Combined VFE vertical elements and GGL centre-pivot roof windows
These combinations extend the possibilities for view, daylight and ventilation at eaves level. Ideal for storey-and-a-half house designs. Made of pine with triple coat nish. Upper centre-pivot section rotates 180 for easy cleaning of outer pane. Vertical element opens inwards from the bottom for ventilation and cleaning.

GGL M06

VFE M31

VFE M34

Vertical elements and centre-pivot combinations
Packages include: Bottom-hung VFE vertical pine nish window and GGL pine nish centre-pivot roof window. Both window types with toughened outer pane with laminated inner pane for additional safety and suitable ashings. GGL SFOL122 GGL SFOL123 VFE + GGL + ashings for slate up to 8mm thick. VFE + GGL + ashings for slate up to 8mm thick. 1.4 W/m2K 1.4 W/m2K 1.4 W/m2K 1.4 W/m K
2 Days 2 Days 2 Days 2 Days

537.00 537.00

560.00 560.00 537.00 537.00 560.00 560.00
GGL SFOW122 VFE + GGL + ashings for tiles up to 120mm in prole. GGL SFOW123 VFE + GGL + ashings for tiles up to 120mm in prole.

Extend the living space to an outside terrace. The top-hung upper element and side-hung lower vertical element combine to produce a doorway to the outside. All other upper elements in the combination are top-hung whilst the vertical elements are xed. Made of pine with triple coat nish. Upper top-hung windows rotate 180 for easy cleaning of outer pane. Roof terrace does require extra work to make external balcony area (i.e. external railings and weatherings).

18mm gap

18mm gaps
Right hand outward opening
Left hand outward opening

158 x 245 U-Value

158 x 245

238 x 245

Packages include: Left or right opening base element, xed elements, top-hung GEL pine window with toughened outer pane and laminated inner pane for additional safety, ashings, EBY adjustable trimmer and rail support. GEL SEOL221 Terrace package + ashings for slate up to 8mm thick. GEL SEOW223 Terrace package + ashings for tiles up to 120mm in prole. GEL SEOL222 Terrace package + ashings for slate up to 8 mm thick. GEL SEOW224 Terrace package + ashings for tiles up to 120mm in prole. GEL SEOL321 Terrace package + ashings for slate up to 8mm thick. GEL SEOW323 Terrace package + ashings for tiles up to 120mm in prole. 1.4 W/m2K 1.4 W/m K 1.4 W/m2K 1.4 W/m2K 1.4 W/m2K 1.4 W/m2K
3,183.00 3,183.00 3,183.00 3,183.00 4,925.00 4,925.00

GGL M08

Natural daylight where you never thought it could reach. Ideal for windowless bathrooms, corridors or cupboards. Exterior at glass rooight appearance. Clear and clean coating keeps glass cleaner for longer. Easy to install with integral ashing. 2-metre exible or rigid tunnel. Rigid 900mm extensions available for deeper roof structures. Double glazed acrylic ceiling diffuser. Comes with white ceiling ring. Optional additional decorative ceiling rings in different nishes are also available. Can be used for night-time lighting with an optional low energy light kit. Ventilation outlet to allow connection of an extractor fan and duct (supplied by others) is available.

Flexible tunnel

Rigid tunnel

Before

Tunnel diameter 35cm 46 x 46

TWF TWR TLF TLR Sun tunnel package with exible tunnel for tiles up to 120mm in prole. Sun tunnel package with rigid tunnel for tiles up to 120mm in prole. Sun tunnel package with exible tunnel for slate up to 8mm thick. Sun tunnel package with rigid tunnel for slate up to 8mm thick.
Package includes: Rooight (46 x 46 cm) with toughened glazing and integral ashing, 2m x 355mm diameter tunnel, double glazed acrylic diffuser with white ceiling ring. 2 Days 2 Days 2 Days 2 Days 172.00 240.00 172.00 240.00
ZTR ZTL 014 ZTV 014 900mm rigid extension section. Low energy light kit, ts inside tunnel, requires bulb and mains connection. Ventilation outlet, allows extractor fan (by others) to be ducted to the outside. Only compatible with TWR and TWF 014 2010. 2 Days 2 Days 2 Days 69.00 45.00 76.00
Additional ceiling trim effect nishes: ZTB ZTB ZTB Brushed aluminium effect. Brass effect. Mahogany effect. 2 Days 2 Days 2 Days 21.00 21.00 38.00
Conservation roof windows
All the technically superior features of a VELUX roof window in a conservation style. With black external proles and glazing bar and recessed installation for slated roofs, the VELUX conservation roof window reects the traditional aesthetics of older skylights. Available in either centre-pivot or top-hung style. Top-hung version is suitable for emergency escape. Top control bar provides background ventilation, even when window is closed. Made of pine with triple coat nish. Rotates 180 for easy cleaning of outer pane.
Installation pitch is dependent on ashing type used.

Centre-pivot

Top -hung For roof pitches from 55-75, please specify special springs when ordering.

55 x 98 U-Value

66 x118
Centre-pivot pine nish GGL SD5N1 GGL SD5P1 GGL SD5W1 GPL SD5N1 GPL SD5P1 GPL SD5W1 GGL + Flashing for slate up to 8mm thick (min 35 roof pitch). GGL + Flashing for plain tiles up to 15mm thick (min 25 roof pitch). GGL + Flashing for tiles up to 120mm in prole (min 15 roof pitch). GPL + Flashing for slate up to 8mm thick (min 35 roof pitch). GPL + Flashing for plain tiles up to 15mm thick (min 25 roof pitch). GPL + Flashing for tiles up to 120mm in prole (min 15 roof pitch).
Packages include: GGL centre-pivot or GPL top-hung roof window, mullion, toughened outer pane with laminated inner pane for additional safety and suitable ashings. 1.4W/m2K 1.4W/m2K 1.4W/m K 1.4W/m2K 1.4W/m K 1.4W/m2K

348.00 348.00 348.00

394.00 394.00 394.00
498.00 498.00 498.00 612.00 612.00 612.00
Top-hung pine nish, suitable for emergency escape

Conservation rooights

GVA top-hung GVT side-hung (suitable for emergency escape)
When building tradition demands a conservation rooight rather than a conservation roof window. With vertical glazing bar the windows are nished in black and manufactured in polyurethane with anodised aluminium sashes. No background ventilation is provided from these rooights when the windows are closed.
GVA top-hung Two-position peg stay. Roong material maximum 60mm in prole thickness.
GVT side-hung Three-position opening handle. Can be used for emergency escape. Roong material maximum 60mm in prole thickness.

46 x 61 U-Value

56 x 98
Rooights supplied with double glazing, mullion and integral ashings. GVA 0059 GVT 154 0059S Top-hung, toughened pane (20 to 60 roof pitch). Side-hung, emergency escape, toughened pane (20 to 65 roof pitch).

3.3 W/m2K 3.1 W/m K

2 Days 2 Days

206.00 245.00

Not Illustrated VLT rooights for uninhabited rooms (not a conservation style roof window)
Rooight supplied with integral ashings. VLT 0000Z Top-hung rooight. (Installation pitch 15-60).

2 Days

46 x 61
For at roofs the VELUX at roof system provides an excellent alternative to, and replacement for, dome rooights. Natural daylight and ventilation are provided as standard from GGL centre-pivot roof windows. Can be either manually or INTEGRA electrically operated. Supplied with insulated wooden kerb.
External window frame size (nominal w x h) cm

47 x 98

55 x 62

78 x 78

94 x 98

134 x 160

Flat roof
Packages include: Insulated wooden kerb, and choice of manually operated or INTEGRA electrically operated GGL centre-pivot, pine nish roof window with toughened outer pane and laminated inner pane for additional safety. On site ashing required. Other window types and variants, including smoke ventilation system, are also available. Structural opening dome replacement (w x h) cm Structural opening new installation (w x h) cm GGL SCOX1 Manual GGL SC0X2 Electric 1.4 W/m2K 1.4 W/m2K 2 Days/7 Days 50 x x 116 381.x x 77 341.00 678.x x 116 374.00 604.x x 93 386.00 492.x x x x 116 424.00 668.x x 135 436.00 544.00 547.00 791.x x 180 633.00 827.00
2 Days /16 Days max. 553.00

Smoke ventilation system

For situations where smoke ventilation is required. Available for either 1m2 or 1.5m2 of smoke free ventilation area. The system can be upgraded to comply with aerodynamic smoke ventilation requirements by the inclusion of the optional external wind deector. All systems certied and tested to EN 12101-2. A version for at roof applications is also available. Single SO6 roof window provides 1m2 of smoke ventilation, whilst the UO8 system provides 1.5m2.

External frame size (nominal w x h) cm 114 x 118 U-Value

134 x 140

Packages include: Single electrically operated GGL pine nish roof window, toughened outer pane with laminated inner pane for additional safety, 1 smoke sensor, 1 break glass point, 1 wall control unit and suitable ashing or kerb. Additional smoke sensors and break glass units can be purchased separately. Electrical control system and wind deector requires installation on-site. GGL SDOL1 GGL + ashings for slate up to 8mm thick (15- 90 roof pitch). 1.4 W/m2K 1.4 W/m K 1.4 W/m2K
1,048.00 1,056.00 1,281.00 200.00
1,501.00 1,530.00 1,747.00 200.00
GGL SDOW1 GGL + ashings for tiles up to 120mm in prole (15- 90 roof pitch). GGL SCOX7 KFD 0000 Flat roof version (0- 15 roof pitch). Wind deector (for compliance to aerodynamic smoke ventilation requirements).

Installation products

Insulation collar BDX Underfelt collar BFX Vapour barrier BBX Support trimmers EBY
Provides the perfect interface between roof window and roong structure to meet building regulations for energy conservation. Includes BFX underfelt collar.
Ensures a tight connection between the roof window and the roong felt or membrane. Quick and easy to t. Includes transverse drainage gutter.
Secure connection between the window and vapour barrier within the roof structure. Ensures warm and humid air from the room does not penetrate through to the roof structure.
VELUX recommend the use of EBY trimmer both for support and nish when installing EBL or EBW twin ashings (18mm frame gap only).
BDX 2000 Insulation collar (also includes BFX collar). BFX 1000 Underfelt collar + transverse drainage gutter. BBX 0000 Vapour barrier collar.

2 Days 2 Days 2 Days

2 Days delivery
(Specify window size when ordering) (Specify window size when ordering) (Specify window size when ordering)
One standard price 24.00 One standard price 16.00 One standard price 16.00
Support trimmer for pine windows

EBY W2000mm long. EBY W2700mm long. EBY W3500mm long.
Support trimmer for white windows

75.00 163.00 211.00

80.00 163.00 211.00

Flashings

min. 15mm

max. 8mm

max. 45mm max. 120mm max. 15mm
For roof pitches from 15-90 degrees. Flashing for installing one roof window into slate up to 8mm thick. Not for interlocking slate.
For roof pitches from 35-90 degrees. For recessed installation of one roof window into slate up to 8mm thick. Not for interlocking slate. Coupled version also available.
For roof pitches from 20-90 degrees. Flashing for installing one roof window in at or proled roong material. Minimum prole of 15mm and maximum prole of 45mm.
For roof pitches from 15-90 degrees. Flashing for installing one roof window in at or proled roong material up to 120mm in prole. Also for interlocking slate, thatch and prole sheeting.
For roof pitches from 25-90 degrees. For installing one roof window in plain tiles (max length 340mm). Maximum thickness of 15mm.
EDL 0000 For slate up to 8mm thick.
C02 31.00 43.00 31.00 36.00 43.00
C04 33.00 55.00 33.00 37.00 55.00
F06 36.00 59.00 36.00 42.00 59.00
M04 35.00 56.00 35.00 42.00 56.00
M06 38.00 61.00 38.00 44.00 61.00
M08 40.00 65.00 40.00 44.00 65.00
P10 43.00 69.00 43.00 49.00 69.00
S06 42.00 64.00 42.00 50.00 64.00
U04 44.00 66.00 44.00 54.00 66.00
EDN 0000 For recessed in slate up to 8mm thick. 2 Days EDZ 0000 For tiles up to 45mm in prole. EDW 0000 For tiles up to 120mm in prole. EDP 0000 For plain tiles up to 15mm thick. 2 Days 2 Days 2 Days
Flashings also available in titanium zinc, copper and a wide range of colours to match the roof window nish. Delivery time is in working days from receipt of order at VELUX for orders placed before 4pm.

Combi-ashings

Twin Coupled Duo Triple Quatro
EBL 0000 Twin EBW 0000 Twin EBL 0050 Twin EBW 0050 Twin
Side by side with 18mm gap for slate up to 8mm thick. Side by side with 18mm gap for tiles max. prole 120mm. Side by side with 50mm gap for slate up to 8mm thick. Side by side with 50mm gap for tiles max. prole 120mm. for slate up to 8mm thick.
C02 81.00 98.00 108.00 110.00 92.00 105.00 138.00 158.00 95.00 100.00 220.00 233.00
C04 87.00 102.00 113.00 115.00 95.00 108.00 142.00 162.00 98.00 102.00 225.00 236.00

Control rods

Telescopic rod for opening centrepivot windows positioned higher than arms reach. Rods can also be used to control VELUX blinds with the addition of an appropriate adaptor tted onto the blind.
Manual controls, locks & restrictors
ZCT 200 ZCT 100 ZOZ 012 ZOZ 147 ZOZ 010 SO11 100-180cm telescopic rod for operation of GGL/ GGU centre-pivot roof windows. 100cm extension for ZCT 200. Security locks Key operated window lock for GGL/GGU centre-pivot roof windows only. Button operated window lock (without key) for GGL/ GGU centre-pivot roof windows only. Opening restrictor with key (cannot be used on top-hung roof windows GPL, GPU, GHL).
7 Days 7 Days 7 Days 7 Days 7 Days
21.28 5.11 26.38 22.38 22.13
SML Roller shutters Electronically operated for tting to VELUX INTEGRA roof windows.
7 Days (Specify window size when ordering)
One standard price 306.38

Glazing options

With so many advantages to each of our options, you can choose the VELUX glazing that suits you best.

--34 Obscure glazing

Privacy without reducing natural daylight ideal for bathrooms. 4mm obscure inner pane. 4mm toughened outer pane with low-E coating.

--73 Glazing

6.4mm laminated inner pane for additional safety. Improved noise reduction compared to --34 and --59 glazing. 4mm toughened outer pane with low-E coating.

--59 Glazing

Energy efficient 24mm double glazing. 4mm oat inner pane with Low-E coating. 4mm toughened outer pane.

New lower U-Value

--60 Glazing
Same characteristics as --73 glazing plus: Premium performance with U-value for the complete window of 1.3W/m2K. Clear and clean coating on outer window, to keep the windows cleaner for longer. 6mm toughened outer with low-E coating for improved energy efficiency. Improved noise reduction compared to --73 glazing.
For optimum performance VELUX recommend use of --73 or --60 glazing variants. All panes are AA re rated. U-values stated for VELUX roof windows are for the complete window and calculated to EN ISO 12567-2.

Replacement glazing and replacement ashings

Replacement window panes

Advances in pane technology allow the upgrading of existing panes to give better heat and sound insulation properties.
55x70 For windows manufactured before April 2001. Window size of pane to be replaced shown in brackets. (9) 55x78 (102) 55x98 (6) 55x98 (104) 70x118 ( 5) 66x118 (206) 78x98 (304) (1) 78x118 78x140 94x160 114x118 134x98 134x140 (306) (308) (410) (606) (804) (808) (14) (2) (3) (4) (7) (8)
Replacement roof window panes

IPL 0059C Glazing.

For windows manufactured from April 2001.

7 Days

35.00 43.00

45.00 46.00

66x118

42.00 55.00

60.00 66.00
78x118 78x140 94x160 114x118 134x98 134x140
IPL 0059 Glazing. IPL 0073 Glazing. IPL 0034 Obscure glazing.

C02 53.00 68.00 41.00

C04 53.00 68.00 46.00

F06 59.00

M04 63.00

M06 63.00

M08 63.00

7 Days 7 Days 7 Days

78.00 68.00 56.00 68.00
84.00 94.00 94.00 94.00 120.00 110.00 85.00 108.00 62.00 54.00 68.00 77.00 118.00 86.00 103.00 110.00
Other glazing units are available on request, please contact VELUX for details.
Replacement window ashings
Allows the upgrading of an older VELUX roof window, into the existing aperture.
55x70 For replacing single roof windows installed before April 2001. (Window sizes to be replaced are shown in brackets). (9) 55x78 (102) 55x98 (104) (6) 66x118 (206) 78x98 (304) (1) 78x118 (306) (14) 78x140 (308) (2) 94x160 (410) (3) 114x118 (606) (4) 134x98 134x140 (804) (808) (7) (8)
EL 0000 For slate up to 8mm thick. EW 0000 For tiles up to 120mm in prole.

C01 29.00 37.00

C02 31.00 36.00

C04 33.00 37.00

F06 37.00 42.00

M04 36.00 42.00

M06 38.00 44.00

M08 39.00 44.00

P10 44.00 49.00

S06 42.00 50.00

U04 44.00 54.00

U08 48.00 57.00

ELX 0000 Adaptor ashings for combinations. 7 Days
1 No per window + standard 100mm combi-ashings required. Further details on request.
V VELUX roof window sizes

Roof windows

55 550

62 624

GGL GVT

70 698

GGL GHL

GGL GGU

(021) G 103

78 778

98 978

31 404

GGL GGU GGL GGU GGL GGU GGL GHL GPU GHL GHL GPU

B04 C04 C

GGU GGL GPU GPL GHL

14 306

GGU GGL GPU GPL

GGU GPU GHL G

GGL GGU GGL GHL GPU GPL

(5) 206

118 1178

GDL GGU G[Glass P10]

GGL GPL

140 1398

10 608

GGL GPL GGU GGL GPU GPL

2007 VELUX GROUP, VELUX VELUX logo, INTEGRA and Room in the Roof are registered trademarks. The io-homecontrol registered trademark and logo are owned by the io-homecontrol association. V-GB 053 0607. VELUX reserves the right to modify, through development improvements, the products displayed in this brochure. Telephone calls may be monitored and recorded for quality control purposes.

(419) [Glass P04]

160 1600

610 810

180 1800

11 312

VEA VEB VEC
Sloped xed additional elements

GIL GIU GIL GIU GIL

92 920

Vertical elements

60 600
VFE VFE 3-1/2-VFE 4/10-VFE

7/8-60 831

Sun tunnel

VFE VFA VFB

VFE VFA VFB 4/10-VFE

7/8-95 834

Sales Support
Fax: 5969 sales@velux.co.uk Technical Support Fax: 9395 technical@velux.co.uk Service Support

VFE VFA VFB 3-1/2-95 334

95 954

TWR TWF TLR TLF

VFA VFB VFA VFB

VFA VFB

115 1154

1/2-115 336

137 1374

mm cm 780 78

942 94

1340 134

Fax: 7961 service@velux.co.uk Internet
S Special GGL sizes are available on request. Not all products and sizes shown on this table are represented in this brochure. Please contact VELUX for further details.

(240)XGB 12003