SWISS AIR FORCE

In 1897 the Original Swiss Army Knife was created in the small village of Ibach, Switzerland. Since that time, Victorinox has become known in more than 100 countries for precision, quality, functionality and versatility. This century old heritage has been extended to Swiss Army Watches and Timepieces. Each reflects the ingenious design and outstanding durability weve come to stand for over the years. Uncompromising craftsmanship makes these watches worthy to carry the cross and shield emblem that symbolizes the legend of Victorinox and the Swiss Army Brand. Whether youre going around the corner or around the globe, this specially designed Swiss Air Force Watchits choice of materials and technologywill make sure that youre equipped for lifes adventures. No matter what those adventures might be.
QUALITY FEATURESSWISS AIR FORCE WATCHES
Made in Switzerland. Precision Swiss Movements. Individually tested for water resistance of 100M (330 feet) or greater. Solid stainless steel cases and/or bracelets on most models. Scratch-resistant sapphire and anti-reflective crystals on most models. Swiss Army Brand Watches are covered by a three-year limited warranty. Only our watches are authorized by the Swiss government to carry the name Swiss Army.
TABLE OF CONTENTS Three Hand Analog Quartz. 2 SeaPlane Strap Replacement System. 5 SeaPlane Chronograph. 8 SeaPlane XL Mechanical. 14 FA-18 Mechanical Chronographs. 16 AirBoss Mach 2/3/4 Using the Visual Countdown. 25 AirBoss Mach 2 Mechanical Self-Winding. 27 AirBoss Mach 3 Quartz Chronograph. 29 AirBoss Mach 4 Mechanical Manual Winding. 35 AirBoss Mach 5 GMT Mechanical Self-Winding. xx AirBoss Mach 6 Mechanical Self-Winding. xx Hunter Mach 2 Flyback Analog Chronograph. 36 Hunter Mach 3 Analog/Digital Chronograph. 48 Tachymeter. xx Battery. 74 Warranty. 75 -1-
THREE HAND ANALOG QUARTZ The crown (C) has three positions: Position 1: Running position (neutral). Position 2: Quick correction of the date. Position 3: Time setting, interruption of circuit for motor (in case of long term storage-to conserve battery life).
(Image illustrates positions 1, 2, & 3 only. See specific instructions for your watch model).
SETTING THE DATE & TIMEPull-Out Crown (AirBoss Mach 1 & 2) A. Pull out the crown to position (2). B. Rotate the crown away from you until the date showing is the day before the desired setting. C. Pull out the crown to position (3) and rotate toward you. When midnight is reached, the date will advance to the desired date. Continue to turn the crown until the desired time is set. Remember, the date advances at 12:00 midnight, not 12:00 noon. D. Push in the crown, returning it to position (1). The date and time are now set. To Set Time Alone Refer to instructions C. NOTE: Gently pull on crown to determine if your crown is a screw-down or pull out. -3-
SETTING THE DATE & TIME - Screw Down Crown (SeaPlane, FA-18, and Hunter watches) A. Using the thumb and forefinger, apply mild pressure on crown while rotating toward you until crown releases. B. Pull out crown to position (2). Turn the crown away from you until the date showing is the day before the desired setting. C. Pull out the crown to the fully extended position (3) and rotate toward you. When midnight is reached, the date will advance to the desired date. Continue to turn the crown until the desired time is set. Remember, the date advances at 12:00 midnight, not 12:00 noon. D. After setting, push in the crown then press and screw down away from you until it is sealed tight into position (1). The date and time are now set. To Set Time Alone Release crown (refer to A) and then follow instruction D.
SEAPLANE CHANGING STRAPS Step 1 Place watch face crystal-side down on a soft cushion surface.
Step 2 Place thumb and forefinger on the fluted ring. Press down and turn counter-clockwise until fluted ring stops.

FLUTED RING

Step 3 Lift off fluted ring and place to the side, exposing strap below.
Step 4 Separate strap from watch back by carefully lifting strap upward.
Step 5 Place alternate band onto watch back, making sure that band is securely seated. The bands buckle should be on the left side of the watch with the crown facing you (see illustration).
Step 6 Replace fluted ring by lining up the three notches.
Step 7 Place thumb and forefinger on fluted ring. Press down and turn clockwise until fluted ring stops, locking strap into place on watch back.
SEAPLANE CHRONOGRAPH This chronograph movement features a 30-minute counter, 110th second timer, sweep second hand and date calendar. It enables short times to be measured to an accuracy of one tenth of a second in a 30- minute totalizer. The crown C has three positions: Position 1: Neutral and winding position (mechanical movement only) Position 2: Correction of the date Position 3: Setting the time, seconds stop IMPORTANT: The SeaPlane Chronograph is fitted with a screw-down crown which must be released before use. Turn crown towards you to release. After use, push the crown back to position 1, then press and screw down the crown (to ensure a tight seal). -8-
SETTING THE TIME Pull out the crown to position 3. The second hand now stops. Turn the crown to pre-position the hour and minute hands to the desired time. Push the crown back into its normal position (1). The watch will begin to run again instantly. SETTING THE DATE Pull out the crown to position 2. Rotate the crown away from you advancing the hour hand until the date showing is the day before the desired setting. Pull out the crown to position 3 and rotate away from you. When midnight is reached, the date will advance to the desired date. Continue to turn the crown until the desired time is set. Remember, the date advances at 12:00 midnight, not 12:00 noon. Push in the crown, returning it to position 1. The date and time are now set. NOTE: You must always push in and screw down the crown to form a water resistant seal with the case. Never operate the crown when the watch is wet. -9-
CHRONOGRAPH FUNCTIONS Start-Stop Function A. Press Push-piece A once to start the timing operation; press again to stop. Restart Timing A. Press Push-piece A again to restart timing. Zero Reset A. Once the timing operation has stopped, press Push-piece B. The chronograph and totalizer hands will reset to zero. Measurement of Partial Times (Addition Function) A. Press Push-piece A again to restart timing. Further pressure on Push-piece A will stop the timing operation. The chronograph will indicate the final time. B. Once the timing operation has been stopped, press Push-piece B. The chronograph and totalizer hands will be reset to zero.

- 10 -

Measurement of Intermediate (Split) Times A. Press Push-piece A to start timing. B. Press Push-piece B to read off the first split time without interrupting the measurement of the total time. C. Press Push-piece B to continue timing. The chronograph will continue its measurement by reverting the 1/10th hand to zero and flying back the other hands to recover the elapsed time. D. Press Push-piece B again to read the second split time. E. Repeat this procedure until the action to be timed has been completed. F. Press Push-piece A to stop timing. G. Once the timing operation has been stopped, press Push-piece B. The chronograph and totalizer hands will be reset to zero. Measurement of Two Times at Very Short Intervals A. This function enables two times separated by a very short interval to be measured. B. Press Push-piece A to start timing. C. Press Push-piece B to stop the first time without interrupting measurement of the second time. - 11 -

D. E. F. G.

Press Push-piece A to stop measurement of the second time. The chronograph will indicate the first time. Press Push-piece B to display the second time. Press Push-piece B again. The chronograph and totalizer hands will reset to zero.
WARNING: Do not activate the Push-pieces under water. REINITIALIZING THE CHRONOGRAPH HANDS Following an incorrect activate, violent impact or exposure to a strong magnetic field, one of the chronograph counter hands may fail to revert to its original position (zero). To reinitialize the hands, proceed as follows: Zero Reset of the Hour Counter Hand A. Pull out the crown to position (2). B. Press Push-piece A briefly until the hand reverts to the original position (on 12).

- 12 -

ZERO RESET OF THE MINUTES COUNTER HAND Pull the crown out to position 2. Press Pusher B briefly until the hand reverts to the original position. ZERO RESET OF THE SECONDS COUNTER HAND Pull the crown out to position 3. Press Pusher A briefly until the hand reverts to the original position. ZERO RESET OF THE TENTHS OF A SECOND COUNTER HAND Pull the crown out to position 3. Press Pusher B briefly until the hand reverts to the original position. NOTE: You must always push in and screw down the crown to form a water resistant seal with the case. Never operate the crown when the watch is wet.

- 13 -

SEAPLANE XL MECHANICAL (MANUAL WINDING) IMPORTANT: The SeaPlane XL Mechanical is fitted with a screw-down crown which must be released before use. Turn crown towards you to release. After use, push the crown back to position 1, then press and screw down the crown (to ensure a tight seal).

The chronograph movement indicates the hours, minutes, seconds and date and enables short times to be measured to an accuracy of 1/5th of a second in a 12 hour period. The crown C has three positions: Position 1: Neutral and winding position Position 2: Correction of the date Position 3: Setting the time, seconds stop NOTE: You must always push in and screw down the crown to form a water resistant seal with the case. Never operate the crown when the watch is wet.

- 18 -

Push-pieces Push-piece A: Chronograph start/stop Push-piece B: Intermediate times Chronograph zero reset Watch Indications F Hours D Minutes G Seconds H Date Chronograph Indications I 12-hour counter E 30-minute counter J 60-second counter

- 19 -

- 20 -
Measurement of Intermediate (Split) Times A. Press Push-piece A to start timing. B. Press Push-piece B to read off the first split time without interrupting the measurement of the total time. C. Press Push-piece B to continue timing. The chronograph will continue its measurement by reverting the 1/10th hand to zero and flying back the other hands to recover the elapsed time. D. Press Push-piece B again to read the second split time. E. Repeat this procedure until the action to be timed has been completed. F. Press Push-piece A to stop timing. G. Once the timing operation has been stopped, press Push-piece B. The chronograph and totalizer hands will be reset to zero. Measurement of Two Times at Very Short Intervals A. This function enables two times separated by a very short interval to be measured. B. Press Push-piece A to start timing. C. Press Push-piece B to stop the first time without interrupting measurement of the second time. - 21 -
WARNING: Do not activate the Push-pieces under water. REINITIALIZING THE CHRONOGRAPH HANDS Following an incorrect activate, violent impact or exposure to a strong magnetic field, one or the other of the chronograph counter hands may fail to revert to its original position (zero). To reinitialize the hands, proceed as follows: Zero Reset of the Hour Counter Hand A. Pull out the crown to position (2). B. Press Push-piece A briefly until the hand reverts to the original position (on 12).

- 22 -

Zero Reset of the Minute Counter Hand A. Pull out the crown to position (2). B. Press Push-piece B briefly until the hand reverts to the original position (at noon.) Zero Reset of the Seconds Counter Hand A. Pull out the crown to position (3). B. Press Push-piece A briefly until the hand reverts to the original position (on 60). Zero Reset of the 1/10th Second Counter A. Pull out the crown to position 3. B. Press Push-piece B briefly until the hand reverts to the original position (on 0). C. Push the crown back down firmly against the case to position (1). NOTE: You must always push in and screw down the crown to form a water resistant seal with the case. Never operate the crown when the watch is wet. - 23 -
USING THE VISUAL COUNTDOWN (AIRBOSS MACH 2 - 3 - 4) *See diagram on page 26 To determine if you have the visual countdown feature, look at the watch dial. You will see an inner bezel. If it has a yellow triangle with numbers counting down clockwise from 60, you have the visual countdown feature. The bi-directional visual countdown is easy to use: A. When rotating the visual countdown turner, simply align minutes on the inner bezel to be counted down with the minute hand (i.e. 20 minutes). B. When the minute hand reaches the yellow triangle (0 minutes), 20 minutes will have been counted down. C. The countdown feature works for a duration between 60 minutes and one minute.

- 24 -

AIRBOSS MACH 2

Visual Countdown turner

AIRBOSS MACH 3

C (recessed crown)

- 25 -
AIRBOSS MACH 2 MECHANICAL (SELF-WINDING) The watch is wound automatically when worn on the wrist. If the watch is not worn on a daily basis, the movement will have to be wound manually by turning the crown away from you at least twenty times in position (1). Setting the Date and Time Wind the movement if necessary. Pull out the crown into position 3. The seconds hand will stop. Make sure that the position of the hands corresponds to a change of date at midnight and not at noon. Turn the crown to pre-position the hands on the desired time. Push the crown back down firmly against the case in position (1).

- 26 -

To Set Time Alone Wind the movement if necessary. Pull out the crown to position (3). The seconds hand will stop. Turn the crown to pre-position the hands on the desired time. Push the crown back down firmly against the case in position (1), and the watch will begin to run again instantly. NOTE: For precise time setting, it is advisable to pass the desired minute and position the hand in the counterclockwise direction.

- 27 -

AIRBOSS MACH 3 - SPECIAL QUARTZ CHRONOGRAPH *See diagram on page 30 To facilitate the use of the AirBoss Mach 3, two original features have been developed: A. Enlargement of the two subdials for easier legibility B. Placement of the chrono pushers on the left side of the case for easy Start/Stop by the thumb.

Setting the date and time The crown (C) has three positions which affect Push button functions: Position 1: Normal position. Push-buttons: chronograph functions. Position 2: Quick correction of time-zones (hour hand). Date corrections by passing through 24 hours. Push-button B (at 10 oclock): Initialization of the timer hand (60-minute counter). Push-button A (at 8 oclock) Initialization of the 12-hour counter. Position 3: Time setting, stopping of the movement (storage). Push-button B: Initialization of the 1/10 seconds counter. Push-button A: Initialization of the 60-second counter. - 28 -
C (recessed crown) 3 positions
5 Visual Countdown turner 8
Push-pieces Push-piece A: Chronometer start/stop Push-piece B: Intermediate times. Chronograph zero reset. Crown C: Recessed, three positions
Watch Indications 1 Date 2 Minutes 5 Hours 8 Visual Countdown ring - 29 -
Chronograph Indications second counter minute counter hour totalizer 7 1/10th second counter
CHRONOGRAPH OPERATING PROCEDURE This chronograph movement features a 60-minute counter-hand (yellow), a 60-second counter-hand (white), one tenth second indicator, and a 12-hour totalizer. Measurement of elapsed times Press Pusher A (at 8 oclock) with the thumb once to start the timing operation. Press again to stop timing. These two operations may be repeated several times, to add short time measurements. Once the timing operation has been completed, press Pusher B (at 10 oclock) briefly until the hands revert to the original position. Measurement of Lap Times A. Press Pusher A again to restart timing. Further pressure on Pusher A stops the timing operation. The chronograph indicates the final time. B. Once the timing operation has been stopped, press Pusher B. The chronograph and totalizer hands are now reset to zero. - 30 -
Measurement of Intermediate (Split) Times A. Press Pusher A to start timing. B. Press Pusher B to read off the first split time without interrupting the measurement of the total time. C. Press Pusher B to continue timing. The chronograph will continue its measurement by reverting the 1/10th hand to zero and flying back the other hands to recover the elapsed time. D. Press Pusher B again to read the second split time. E. Repeat this procedure until the action to be timed has been completed. F. Press Pusher A to stop timing. G. Once the timing operation has been stopped, press Pusher B (at 10 oclock) briefly until the hands revert to the original position. The chronograph and totalizer hands will be reset to zero.

- 31 -

REINITIALIZING THE CHRONOGRAPH HANDS Following an incorrect activate, violent impact or exposure to a strong magnetic field, one of the chronograph counter hands may fail to revert to its original position (zero). To reinitialize the hands, proceed as follows: Zero Reset of the Hour Counter Hand A. Pull out the crown to position (2). B. Press Push-piece A briefly until the hand reverts to the original position (on 12). Zero Reset of the Minute Counter Hand A. Pull out the crown to position (2). B. Press Push-piece B briefly until the hand reverts to the original position (at noon.) Zero Reset of the Seconds Counter Hand A. Pull out the crown to position (3). B. Press Push-piece A briefly until the hand reverts to the original position (on 60). - 32 -
Zero Reset of the 1/10th Second Counter A. Pull out the crown to position 3. B. Press Push-piece B briefly until the hand reverts to the original position (on 0). C. Push the crown back down firmly against the case to position (1). NOTE: You must always push in and screw down (if applicable) the crown to form a water resistant seal with the case. Never operate the crown when the watch is wet.

- 33 -

AIRBOSS MACH 4 - MECHANICAL MANUAL WIND Setting of the time and winding the watch. Position 1: Normal position. The best way to wind your watch is to do it everyday at the same time, (i.e. every morning). This way, your watch is working at its best and will never stop. Turn the crown (C) away from you, until you meet a resistance of the mechanism. The power reserve will be 56 hours minimum. Position 2: Setting the time. Turn the crown to set the hour and the minute.

- 34 -

AIR BOSS MACH V GMT ANALOG QUARTZ Step 1: Using the rotating crown A (see Figure 1), rotate inner bezel to select the time zone where you currently are and align it with City marking at 12 o'clock.
Line Up Current Time Zone with City Marking at 12 Oclock GMT Military Time Scale on Inner Bezel 1 B

Rotating Crown A

Pull Out Crown to Set Time & Date
Step 2: Setting the Date & Time: Remember, when setting the date it advances at 12 midnight, not 12 noon. - 35 -

Figure 1

A. Pull crown B (see Figure 1) out to Position 2 (middle position), rotate the crown toward you until the date showing is the day before the desired date. B. Pull crown B (see Figure 1) out to Position 3 (fully extended) and rotate toward you. When midnight is reached, the date will advance to the desired date. Continue to turn the crown until the desired time is set. Push in crown, returning it to Position 1. Step 3: Setting the GMT time (Hand with Red Arrow): NOTE: GMT time is on a 24 hour military time scale (see Figure 1). A. Pull crown B out to Position 2 (middle position) and rotate away from you to adjust the GMT arrow hand to your local time. (Example - 7pm is 19 hours military time). B. Push in crown B, returning it to Position 1.

HUNTER MACH 2 FLYBACK ANALOG CHRONOGRAPH Setting the Time and Correction

- 43 -

HUNTER MACH 2 FLYBACK ANALOG CHRONOGRAPH Timing ModeSimple Timing Function

- 44 -

HUNTER MACH 2 FLYBACK ANALOG CHRONOGRAPH Timing ModeAdd Function

- 45 -

HUNTER MACH 2 FLYBACK ANALOG CHRONOGRAPH Timing ModeSplit TIme

- 46 -

HUNTER MACH 2 FLYBACK ANALOG CHRONOGRAPH Timing ModeSplit TIme (cont.)

- 47 -

The time captured can be 30 minutes at max. (Exclusive worldwide function).

- 48 -

HUNTER MACH 2 FLYBACK ANALOG CHRONOGRAPH Timing ModeMemo Function

- 49 -

HUNTER MACH 2 FLYBACK ANALOG CHRONOGRAPH Timing ModeMemo Function (cont.)

- 50 -

- 51 -
HUNTER MACH 2 FLYBACK ANALOG CHRONOGRAPH Timing ModeFly-Back Function

- 52 -

HUNTER MACH 3 ANALOG/DIGITAL CHRONOGRAPH (PULL-OUT CROWN)
FUNCTION AND DISPLAYS Lighting Dial lighting Hands and Date Only Analog hour, minute and second display (hands) Digital display of date only. T1-Digital Local Time and Date Digital display of hours, minutes, seconds and date.

29:09:99

10:10:40

- 53 -

T2-Second Time Digital display of a second time: another time zone hour time summer/winter time

11:10:40

Week Number Digital display of day, week number (may also be hidden), date, month and year.

31:12:99

AL-Daily Alarm Alarm time may be programmed in hours and minutes.

06:15:on

- 54 -
AG-Annual Alarm Calendar alarm; digital display of annual alarm, showing date, month, year alternating with the hour, minutes and alarm activation.

31:12:99 08:00:on

08:00:on
CHR-Chronograph Chronograph in hours, minutes, seconds, hundredths of a second up to 24 hours and in days, hours and minutes over 24 hours up to 99 days.

R 0 CH

00:00:00

- 55 -

TM-Timer Programmable in days, hours, minutes and seconds up to 99 days.
EOL-Battery End of Life Indicator This indicator shows that the battery should be replaced (within 2 weeks). The EOL is shown in the neutral selection by the appearance of EOL or by other functions flashing when the crown is in the neutral position.

- 56 -

2. SETTINGS The various functions are selected by turning the crown. There are three crown positions: pushed in (Pos. 0) neutral (Pos. 1) pulled-out (Pos. 2)

(Pos. 0)

(Pos. 1)

(Pos. 2)

In the neutral position, you can select various functions by rotating the crown. In the pulled-out position, function data may be adjusted by turning the crown. The crown may be turned in both directions. In addition to the crown, the watch has two buttons A and B the action of which depends on the function selected. Depending on the action required, choose either: brief press or long press (1 to 2 seconds) - 57 -

The hands are successively synchronized by turning the crown. The second hand can only be adjusted in a clockwise direction (crown turning upwards). Push the crown back into position 1 when the position of the three hands corresponds to the digital time displayed. This synchronization only adjusts the time displayed by the hands to local time (T1). For perfect synchronization between analog time (hands) and digital time (figures), first adjust the hands to the digital time displayed (in synchronization mode R) and then adjust the exact time in Setting mode as shown on page 50.

- 62 -

6.2 Setting Select the T1 (TIME) function, then pull the crown to position 2.

22:10:40

6.2.1 Selecting the 24 hour or AM/PM system. The digital time (figures) can be changed to display in either 24 hour or AM/PM mode by briefly pressing button A.
6.2.2 Setting the digital hours, minutes and seconds Press button B briefly; the hour, minute and second figures are selected and will flash successively. The hour, minute and second figures can be successively adjusted by rotating the crown. Push the crown back to position 1 after adjustment. - 63 -
6.3 Neutral display, with or without date Neutral display, selected by turning the crown, allows only the hands to appear; the digital date may be displayed or hidden. The date display may be activated or deactivated in this mode by pressing button A briefly.
6.4 Selecting and setting the full date Instructions starting page 46.

22:03:99

- 64 -
6.4.1 Setting Day/Month (D-M) or Month/Day (M-D) Select full date display by turning the crown. Pull the crown to position 2 Briefly press button A to select date display mode
Day (D) / Month (M) or Month (M) / Day (D). 6.4.2 Setting the date, month and year The date (D), month (M) and year are changed by rotating the crown. The day of the week is automatically selected according to the date. Press button B briefly to confirm date setting (D), then confirm the month (M) and year.

- 65 -

6.4.3 Choosing and setting one of the four languages for day name display Select one of four languages available for the day display by pressing and holding button A. Turn the crown (in position 2) to display the name of the day in either (F) French, (E) English, (D) German, (S) Spanish. All date settings as described in 6.4.1 to 6.4.3 are confirmed by pushing the crown back to position 1. 6.4.4 Deactivating the week number display The week number display is deactivated by pressing button A briefly (crown in position 1). It will reappear after another function is selected by turning the crown. Repeat if necessary.

- 66 -

6.5 Setting a second time zone (or home time or summer/winter time) In local time (T1) display, select the second time zone (T2) function by briefly pressing button B then pulling the crow to position 2. The time of the second time zone (T2) may be changed to display in the 24 hour or AM/PM system by briefly pressing button A. The hours and minutes are set by turning the crown. Briefly press button B to confirm setting of the T2 hour, then adjust the T2 minutes and confirm again. Briefly press button B again to set the date for the second time zone chosen.

- 67 -

6.5.1 Date of the second time zone option If you wish, you may set the date of the second time zone with a variation of plus or minus 1 day to local time (T1). E.g., If the date in the local time is the 25th, the date of the second time zone is either the 24th or 26th (maximum difference between two time zones is one day). 6.5.2 Setting the date of the second time zone After you have pressed button B a third time as described in 6.5, you may set the date of the second time zone by turning the crown. The message NO OPERATION shows that it is not possible to adjust the date by more than plus or minus 1 day. Push the crown back to position 1 after adjustment.

26:12:99 N

NO O RATIO PE

- 68 -

6.6 SETTING THE ALARM (DAILY ALARM) 6.6.1 Starting the alarm Select the alarm function (AL) by turning the crown and pressing and holding button A. The letters ON will appear on the dial and a beep will be heard. 6.6.2 Alarm sound At the chosen alarm time, a first alarm will sound. After 10 seconds, the alarm will sound intermittently for 50 seconds and then stop automatically. 6.6.3 Stopping the alarm The alarm may be stopped at any moment by pressing either of the buttons or the crown.

Alarm ON/OFF

07:10:on

Striking mechanism test:

Press and hold button B
6.6.4 Testing the alarm sound (applicable to all alarms) When the alarm (AL) function is selected, the alarm sound may be tested by pressing and holding button B. The same test may be used for Timer and Diary alarms. - 69 -

6.8 CHRONOGRAPH Select the chronograph (CHR) function by turning the crown. 6.8.1 Measuring one single time or adding several R 0 CH times with automatic subtraction of intermediate stops (ADD) 00:00:00 START timing by briefly pressing button A STOP timing by briefly pressing button A Reading the measurement: the 2 figures positioned to the right of the letters Add show the number of hundredths of a second. Example of reading a time: 00:01:59 Add 36 shows that the event timed has lasted for 0 hours,1 minute 59 seconds d 3 Ad and 36 hundredths of a second. Reset the chronograph by pressing button B briefly. 00:01:59 Add mode allows several timings to be added while automatically subtracting the duration of intermediate events by pressing Start-Stop-Start-Stop-etc. Total reading timeresetting. For example, total duration of journey from town A to town D with subtraction of stops in towns B and C.

- 73 -

6.8.2 Measuring the total time with intermediate time reading (SPLIT or fly-back hand) This function allows, for example, the total duration of a race and the individual time taken by each individual runner to be measured. START of timing by briefly pressing button A. SPLIT X of timing by briefly pressing button B when runL 8 SP ner X finishes. In the example opposite (SPL), the time 00:03:40 taken by runner X is 0 hours, 3 minutes, 40 seconds and 85 hundredths of a second. RESTART timing by briefly pressing button B. The chronograph flies back to the time passed since Split X and continues measurement (CHR). R 1 CH SPLIT Y of timing by briefly pressing button B at the finish of runner Y (SPL). 00:04:50 RESTART timing by briefly pressing button B. The chronograph flies back to the time passed since Split Y and continues timing (CHR). STOP Z by briefly pressing button A. Reading time of last runner Z and the total race time: 0 hours, 5 minutes, 20 seconds and 56 hundredths (Add). RESET by briefly pressing button B (CHR).

- 74 -

6.8.3 Displaying a chronograph time exceeding 24 hours (Possible duration up to 99 days). The timing for a chronograph duration of up to 24 hours is displayed in hours, minutes and seconds and hundredths of a second. For any time exceeding 24 hours, the result is displayed in days (instead of hundredths of a second, max. 99 days), hours (max. 23 hours), minutes (max. 59 minutes) and seconds (max. 59 seconds).

d 5 Ad

- 80 -

THREE-YEAR LIMITED WARRANTY:
Swiss Army Brands, Inc. warrants, for a period of three years from the date of original purchase, the face, hands and movement of this Swiss Army Brand Watch to be free from defects in material and workmanship. If any of the aforementioned parts are defective we will, at our option, either repair or replace the watch, without charge. Visit our website to find a Swiss Army Authorized Repair Center or call us at 1-800-442-2706. While there is no charge for repair or replacement of the watch during the warranty period, a check in the amount of $10.00, payable to Swiss Army Brands, Inc., must accompany the watch to cover postage, handling, insurance and related costs. As a condition to this warranty, either the enclosed warranty repair coupon, completed in its entirety and date stamped by the retailer from whom the watch was purchased, or the original retail purchase receipt, must be presented with the watch upon return. Alternatively, if you purchase the watch in California, you may return the watch to the retailer from whom it was purchased and the return postage will be processed without charge. Please include your name, street address and phone number to ensure proper return. This warranty does not apply to any part of the watch not expressly warranted herein or damage to the watch while in the possession of the consumer or damage or defect caused by abnormal or unreasonable use (including repairs or alterations by a person other than Swiss Army Brands, Inc.). This warranty gives you specific legal rights and you may also have other rights which vary from state to state. The foregoing warranty is exclusive and in lieu of all other warranties of quality and performance, written, oral or implied, and all other warranties, including any implied

- 81 -

warranties of merchantability or fitness for a particular purpose, are hereby disclaimed. In no event shall Swiss Army Brands, Inc. or its affiliates be liable for special, indirect, incidental or consequential damages whether in contract, tort, negligence, strict liability or otherwise. Some states do not allow limitations on how long an implied warranty lasts and/or the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you.

- 82 -

THREE-YEAR LIMITED WARRANTY REPAIR COUPON
Name ______________________________________________________ Address ____________________________________________________ City ________________________________________________________ State ________Zip______________Date of Purchase ____________ Purchased from______________________________________________
Repair Coupon. To be detached and submitted with watch only when watch is returned for repair covered by the warranty.