UR 810 UNIVERSAL CONTROLLER
(GB) Instructions (D) Bedienungsanleitung (F) Notice demploi (E) Instrucciones para el uso (I) Istruzioni per luso (NL) Gebruiksaanwijzing (PL) Instrukcja obsugi (CZ) Nvod k obsluze (P) Manual de instrues (DK) Betjeningsvejledning (S) Bruksanvisning (RUS) (GR) 31 (GB) Instructions VIVANCO UR 810 remote control for almost all TV, audio, video and other infrared-controllable appliances Inserting the batteries Open the battery flap on the back of the remote control, press the flap lightly downwards, then insert 2 alkaline AAA batteries. Check that the polarity markings on the batteries and in the battery compartment are correctly lined up (+=+), then close the flap carefully. Always use undamaged batteries. Adapting to appliances In order to control your appliances you must adapt or set the remote control to them. There are three ways of doing so: direct control code entry, code search or learn. If your UR 810 does not understand you, it blinks several times and you can then repeat the entry. Each understood entry is confirmed by an appliance button blinking once briefly. Direct control code entry using the enclosed list Example: setting to control a Panasonic television set: 1. The enclosed list gives, for example, the Panasonic Code 153. Please make sure you have selected the correct list for television sets (TV). 2. To prepare code entry, press the SET button, keep it pressend and then press the required appliance button, e.g. TV, additionally until the lamp (LED) inside lights constantly. 3. Then press the number buttons (e.g. 3) in sequence. 4. Once the numbers have been entered the button lamp goes out and the remote control is ready to control your appliance. 5. Finally, test the control code setting by trying to control (in this example) your television set. If it does not work at all or not correctly try a different code from the list or the code search (see below). 6. To set the remote control for other appliances, proceed in the same way. Instead of the TV appliance button, press another button e.g. VCR, DVB (SAT, DECODER), DVD). Code search If the brand of your appliance is not in the list or none of the codes given fits, we recommend a code search.
Vivanco GmbH, D-22926 Ahrensburg, E-Mail: hotline@vivanco.de, Helpline: +49 (0) 4102 231135
Manual code search 1. Switch on the appliance to be controlled. Program is running. 2. To prepare code search, press the SET button, keep it pressed and then press the required appliance button, e.g. TV, additionally until the lamp (LED) lights constantly. 3. Then point the remote control at the appliance to be controlled. 4. Briefly press the ON/OFF (appliance on/off) button once. The lamp (LED) blinks. Except when searching for a TV code you can also briefly press the yellow > (Play) button and use the Play function to search. Make sure that a tape, a DVD or a CD is inserted in the tape deck, player or recorder. 5. Press the ON/OFF (appliance on/off) or Play button repeatedly, approx. every 1,5 seconds, until the appliance, e.g. your DVD player, reacts. - If you notice the reaction of your appliance too late and the next code has already been emitted you can go back by pressing SET and then ON/OFF or Play again. If your appliance has switched itself off you must switch it back on again, e.g. on the appliance or with the original remote control, to continue searching. - When your appliance reacts you can also try out other buttons without interrupting the search. If some buttons do not work properly, simply continue searching with ON/OFF or Play. 6. When your appliance reacts correctly, press the appliance button, e.g. TV, and end the search. The lamp (LED) goes out. - The UR 810 continues with the search at the point where you interrupted it. When the end of the code list is reached the search stops automatically. The remote control blinks quickly several times. The code last entered remains stored. The search stops after approx. 30 seconds of inactivity. Automatic code search Your remote control finds the correct settings almost automatically in seconds: 1. Switch on the appliance to be controlled. A channel number, for example, appears in the display of your satellite receiver. 2. To start the code search, press the SET button, and then additionally the required appliance button, e.g. TV, for more than 3 seconds until the lamp (LED) starts to blink. 3. Then point the remote control at the appliance to be controlled while the remote control emits a different ON/OFF signal every 2 seconds. 4. When your appliance reacts, press any button, except SET, to end the search. If you ended the search too late, continue to search using the Manual Code Search (see above). 5. Finally, test the control code setting by trying to control, for example, your DVD appliance. If it does not work correctly, please try the code search again. The code search then begins with the next code in the sequence. - Remember to switch your appliance, e.g. DVD, back on again if you wish to continue searching. Code identification You can read off the 3-digit codes you have set at any time: 1. Press the appliance button of the appliance which code you want to read off, e.g. TV. 2. Press the SET button and 1,2,3, depending on the part of the code you want to read off. For example, if you press SET+1 after TV and the code 156 (in this example) has been set, the lamp blinks once after SET+1 is released to show that the hundred figure is 1. All you have to do is count. The ten figure is indicated after SET+2 is released, e.g. it blinks 5 times for the 5 in 156. The one figure is indicated after SET+3 is released, e.g. it blinks 6 times for the 6 in 156. Learning, Programming, of Missing Control Functions The LEARN function is used to supplement the preprogrammed codes. The standard code may provide most of functions needed, but you may miss some key functions. Or you didnt find any functioning preprogrammed code for a device. You can capture upto 100 key funtion codes, max 40 per device. The last captured function will overwrite the previous. learnt. 1 For learning of key codes you must use a functioning orginal remote controller. Please use fresh batteries for both remote controls. 2 Please point the originals remote control transmitter LED towards the receiver LED of UR 810 (placed on top, same as transmitter LED). Distance of LEDs between both remotes shall be approximately 30mm and must be in straight line of sight. 3 Press down and hold the Learn key and press the device key (e.g. DVD) additionally and then release the both pressed keys. Then e.g. the DVD device key starts blinking indicating that DVD key codes (functions) can be captured. 4 Press and release the target key, that you want to learn to (reprogram) (e.g. POWER), the device button lights up. 5 Press and hold the source key on the

original remote control (e.g. POWER) until the LED (e.g. DVD) on your UR 810 remote control blinks twice, then lights up for 2 seconds and then starts blinking again.That indicates that a new function code, e.g. POWER, has been learnt. 6 Repeat steps 4 to 5 to for capturing more key functions. - If there is a learning(capturing) problem, the LED blinks 4 times, lights up for 2 seconds and then will start blinking again. Then start capturing the key function again at step 4. 7 Press and release device key for exit of learning mode. The controller will exit the learning mode automatically after about 30 seconds of inactivity. Reset/deletion of all captured key functions per device: press the right device selection key, e.g. DVD, and then SET and 4 together in order to delete all learnt functions. The appropriate device key LED will flash twice for confirmation. Memory full indication: if the memory is full, a LED blink 4 times and then the controller will exit learnning mode. Operation You operate your appliances basically in exactly the same way as if you were using the original remote controls, except that you must first press an appliance button (TV, DVD, etc.) to control the required appliance. As the symbols on the UR 810 could differ from those on the original remote controls you may have to try out all the buttons in order to find the functions. Special settings and functions 1. Assigning volume and mute exclusively to one appliance (punch through function: Press the appliance button of the appliance that you always want to use for volume control, e.g. DVB. To lock, press SET and 5. To unlock, press SET and 6. 2. Device Selection Key Shift: In order to change the function of a device selection key, e.g. change device key AUX1 to a second SAT device key proceed as follows: a) Press SET hold it and then press the to be changed device key, e.g. AUX1. Then release both keys and the AUX1 light will be on. b) Press SAT, the light goes off and you can enter another SAT code for a second SAT or DTT receiver under AUX1. c) You can reset this function by pressing SET and the modified device key (AUX1) simultanously until the LED goes on. Then release the keys and press the modified device key (AUX1) again. 3. Locking and unlocking a set device key: Press the appliance key of the appliance that you always want to be locked. Preset code not changeable. To lock, press SET and 7. To unlock, press SET and 8. 4. Reset remote control to factory settings: Press SET and 0 simultanously for more then 3 seconds. A LED will flash twice and all user settings will be deleted Specifications Batteries: 2x AAA batteries, R03, UM4 Range: max. 7 m Not for 400 kHz equipment 2-year works guarantee Should your UR 810 cease to work within 2 years of purchasing you will receive a free replacement from VIVANCO. Exceptions: missing codes, deliberate destruction and normal wear and tear of the housing and buttons. (D) Bedienungsanleitung Fernbedienung Vivanco UR 810 fr fast alle Fernseh-, Audio-, Video und anderen infrarotsteuerbaren Gerte Batterien einlegen Bitte ffnen Sie die Batterieklappe an der Gerterckseite, Klappe leicht nach untenschieben, und legen Sie 2 AlkaliMikrozellenbatterien ein. Achten Sie auf die angegebenen Polaritten auf Batterien und im Batteriefach (+=+), und schlieen Sie das Fach wieder vorsichtig. Bitte achten Sie darauf, immer einwandfreie Batterien zu verwenden. Gerteanpassung Um Ihre Gerte steuern zu knnen, mssen Sie die Fernbedienung fr Ihre Gerte einstellen. Dazu gibt es zwei Mglichkeiten: die direkte Steuerkodeeingabe und die Kodesuche. Wenn die UR 810 Sie nicht versteht, dann blinkt sie 2 Mal und Sie knnen danach die Eingabe wiederholen. Jede verstandene Eingabe quittiert sie mit einem kurzen Blink ihrer LED-Anzeigelampe. Die direkte Steuerkodeeingabe mithilfe der beigefgten Liste Beispiel: Einstellung der Fernbedienung fr ein Panasonic-Fernsehgert: 1. Aus der beigefgten Liste entnehmen Sie z.B. den Panasonic-Code 153. Bitte vergewissern Sie sich, dass Sie die korrekte Liste fr Fernseher (TV) gewhlt haben.