Power Horn Remote Siren (105dB) Receiver
Plugs Into Outlet *** Receives X10 Commands
Description: This is a plug-in X10 PRO Siren produces a "High Pitched Chirp" at levels of 105dB. This unit can also be used as an

Annunciator.

Specific Requirements: 120VAC. Excites with Continuous ON/OFF cycle (2 cycles minimum), 4 Second delay on startup and shutdown. Excites with Continuous ALL Lights ON/ALL Units OFF cycle (2 cycles minimum), 4 Second delay on startup and shutdown. Optional / Supplementary Devices & Modules:
Works with X10 Security Systems/Voice Dialers/Personal Assistants such as: PRO2000 Digital Security Console, PSV067/DS7000 Voice Dialer Security Console, PA5800/PPC01Personal Assistant Console. Works with PSC01 PowerFlash Security Interface Module. Numerious commercial Security Systems which have X10 Command Capability buit in.

X10 Protocol:

House Code Dial - Letters A-P, Default "A" Unit Number Dial - Numbers 1-16, Default "1" Each X10 Receiver Module is set to a unique Unit Number or to an identical Unit Number as desired. Each X10 Controller operating a specific set of Receiver Modules must be set to the same House Code as the Receivers they are controlling.

Electrical Protocol:

Nearly all residential homes are wired SPLIT-PHASE. Each 120V Phase is NOT directly connected with the other 120V phase. If after installation, an X10 Receiver does not respond to a remote Controller, then check to ensure that the breaker serving the X10 Receiver is on the same phase as the Controller. If not, the breaker can be changed to the opposite phase. An alternative solution is recommended, to install a Phase Coupler for improving remote communications throughout the home. See www.x10pro.com, then select Technical Support and PLC Troubleshooting.

Installation: Siren Mode

1. Plug-in the Siren to the desired 120VAC wall outlet. Multiple Siren Modules can be used simultaneously, set at the same X10 Address, i.e. - "A1". 2. Determine your system type, which will be exciting the Siren: a. Commercial Security Panel with X10 Command Capability: I. Program in the House Code "A" and Unit Number "1" per Panel instructions. II. Program the Panel, when in Alarm condition, to send an X10 ON & OFF Command-cycle, continuously. III. Siren will excite 4 seconds after cycle starts. Siren will quiet, 4 seconds after cycle ceases. b. Non-X10 capable Security Panel, uses the PSC01 PowerFlash Security Interface module. I. Program Panel to emit a Voltage (max 18VDC) or a Contact Closure during an Alarm condition. II. Plug-in the PSC01 to a wall outlet and connect the PSC01 to the security panel appropriately. See PSC01 Instructions. III. Set PSC01 to "A" for Voltage, "B" for Contact Closure, Mode "2" for Flashing ON/OFF Mode. (Paragraph 2.a.III. applies.) c. X10 PRO Security System. I. Refer to the X10 PRO Security System Installation Instructions for proper use of an X10 Siren. II. An X10 Siren can be excited by either a continuous ON/OFF or All Lights ON/All Units OFF cycle. d. Manual Excitation. I. Using any X10 Controller, perform two ON/OFF cycles with the control button pertaining to the Siren's set Address. II. As long as the manual ON/OFF cycle is maintained, the Siren will continue sounding. Annunciator Mode - performed by any type X10 Controller 1. Send an X10 ON Command at the siren's set address, i.e. - "A1" 2. Then send an X10 Brighten/Dim Command Cycle. Brighten emits a High Pitched Chime, Dim emits a Low Pitched Chime.

Tampa, FL 33542

PSH02_03_03/07 Technical Support: (800) 832-4003

Applicable wire size is 0.4
Use a pressure terminal (M3) when connecting to the terminal

Indicatio n Level

Change Set Value

Set Value

Change Set Digit Change Decimal point and Polarity

Change Set Digit

False logic when COM and pin28 are open, True logic when both are shorted
Polarity Indicated Value + Decimal Point
This manual may not be reproduced to any form in whole or in part. Then contents in this manual may be updated without prior notice.
HEAD OFFICE FACTORY BRANCH OFFICE
1-17-16,NISHI-HOKIMA,ADACHI-KU,TOKYO 121-0812 JAPAN 5-24-27,HOKIMA,ADACHI-KU,TOKYO 121-0064 JAPAN 1-5-16,ENOKOJIMA,NISI-KU,OSAKA 550-0006 JAPAN
Tel.03(3850)5431/Fax.03(3850)5436 Tel.03(3858)3241/Fax.03(3859)1240 Tel.06(6448)3412/Fax.06(6448)Jan 2009