w e Replace the compartment cover, making

AC outlet

Adaptor
sure that it locks rmly in place.
w Connect the AC adaptor to the power supply jack. e Plug the AC adaptor into an AC outlet.
Unplug the AC Power Adaptor when not using the instrument, or during electrical storms. Never interrupt the power supply (e.g. remove the batteries or unplug the AC adaptor) during any DD-65/YDD-60 record operation! Doing so can result in a loss of data. Even when the instrument is turned off, electricity is still owing to the instrument at the minimum level. When you are not using the instrument for a long time, make sure you unplug the AC power adaptor from the wall AC outlet.
Never connect or disconnect the AC power adaptor when the power is on and the batteries are installed. Doing so will turn the power off.
For battery operation the instrument requires six 1.5V C size, LR14 or equivalent batteries. (Alkaline batteries are recommended.) When battery power becomes too low for proper operation, the volume may be reduced, the sound may be distorted, and other problems may occur. When this happens, make sure to replace all batteries, following the precautions listed below.
Use alkaline batteries for this instrument. Other types of batteries (including rechargeable batteries) may have sudden drops of power when battery power becomes low. Make sure to install the batteries with the proper orientation, maintaining the correct polarity (as shown). Incorrect battery installation may result in heat, re and/or leaking of corrosive chemicals. When the batteries run down, replace them with a complete set of six new batteries. NEVER mix old and new batteries. Do not use different kinds of batteries (e.g. alkaline and manganese) at the same time. If the instrument is not to be in use for a long time, remove the batteries from it, in order to prevent possible uid leakage from the battery.

Using Batteries

q Open the battery compartment cover located
on the instruments bottom panel.

Connecting headphones (PHONES/OUTPUT Jack)
voices as well. Connect the supplied Pedal 1 to the PEDAL 1 jack and Pedal 2 to the PEDAL 2 jack.
Make sure that the pedal plugs are properly connected to the PEDAL jacks before turning on the power.
The DD-65/YDD-60 speakers are automatically shut off when a plug is inserted into this jack. The PHONES/OUTPUT jack also functions as an external output. You can connect the PHONES/OUTPUT jack to a keyboard amplier, stereo system, mixer, tape recorder, or other line-level audio device to send the instruments output signal to that device.
Avoid listening with the headphones at high volume for long periods of time; doing so may not only result in ear fatigue, it may be damaging to your hearing.

Using the MIDI Terminals

other MIDI instrument
To prevent damage to the speakers, set the volume of the external devices at the minimum setting and turn power off the devices before connecting them. Failure to observe these precautions may result in electric shock or equipment damage. Also, be sure to set the volumes of external devices at their minimum levels and gradually raise the volume controls while playing the instrument to set the desired listening level.
The instrument also features MIDI terminals, allowing you to interface the instrument with other MIDI instruments or computers. (For more information, see page 30.)
MIDI cables (sold separately) must be used for connecting to MIDI devices. They can be bought at music stores, etc. Always use a high-quality MIDI cable to connect MIDI OUT to MIDI IN terminals. Never use MIDI cables longer than about 15 meters, since cables longer than this can pick up noise which can cause data errors.
Connecting an audio source (AUX IN Jack) Turn on the power Turn down the volume by turning the [MASTER VOLUME] control to the left and press the [STANDBY/ON] switch to turn on the power. Press the [STANDBY/ON] switch again to turn the power off.
This jack is for connection to an external audio source. You can play the instrument with backing music and accompaniment, like playing with a full band. Adjust the input level from the volume control of the external audio source for optimum balance. Connecting Pedals 1 and 2
Even when the switch is in the STANDBY position, electricity is still owing to the instrument at the minimum level. When you are not using the DD-65/YDD-60 for a long time, make sure you unplug the AC power adaptor from the wall AC outlet, and/or remove the batteries from the instrument. Never interrupt the power supply (e.g. remove the batteries or unplug the AC adaptor) during any record operation on the instrument! Doing so can result in a loss of data. While the data is being recorded (-appears and moves from left to right on the display), never interrupt the power supply (e.g., remove the batteries or unplug the AC adaptor). Doing so can result in a loss of data. DD-65/YDD-60 Owners Manual

Pedal 1

Pedal 2
These jacks for connection of the Pedal 1 or Pedal 2 footswitches. These pedals can be used simultaneously play the drum sets hi-hat pedal or bass drum voicesor they can also be assigned to play other

Panel Controls

Front Panel

!8 e r t

!0 !1 !2 !3 !7

u o !4 !56 !6

Front Panel
q w e r t y u i o !0 !1 !2 !3 !4 !5
[MASTER VOLUME] control. 12 DIAL... 15 [ASSIGN] button.. 16 [REVERB] button.. 17 [HAND PERC.] button.. 14 [KIT] button.. 15 [CLICK] button.. 19 [SONG] button.. 22 [TEMPO] button.. 25 PART MUTE [DRUM 13], [BACKING] buttons.. 26 [FUNCTION] button.. 12 [DEMO] button.. 12 [STANDBY/ON] button.. 12, 36 [REC] button.. 28 [BREAK/TAP] button. 23, 26

!6 !7 !8 !9

[A-B REPEAT] button. 27 [START/STOP] button. 12, 22 DISPLAY.. 15 DRUM PAD x 8.. 13

Rear Panel

Since speakers are built into the DD65/YDD-60, you should be careful to never leave any video tapes, cassette tapes, oppy disks or any kind of magnetic storage media on the paneldoing so may result in data loss or damage to the items. Also avoid using the DD-65/YDD-60 near a television or computer monitor, since interference may result. Use the sticks with caution. Do not use them for anything other than playing the instrument. Also, to avoid damage or injury, refrain from waving them recklessly or throwing them.

Drum Sticks

Rear Panel

@0 @1 @2 @3 @4 @5

[DC IN 12V] (AC Adaptor) jack. 8 [AUX IN] jack.. 9 [PHONES/OUTPUT] jack.. 9 [PEDAL 2] Jack.. 9 [PEDAL 1] Jack.. 9 [MIDI IN/OUT] Terminals.. 9, 30
Using the Foot Pedals (1/2) When connected, these pedals can be used simultaneously play the drum sets hi-hat pedal or bass drum voicesor they can also be assigned to play other voices as well. Connect the supplied Pedal 1 to the PEDAL 1 jack @4 and Pedal 2 to the PEDAL 2 jack @3.
Make sure that the pedal plugs are properly connected to the PEDAL jacks before turning on the power. Do not press the pedals while turning the power on. Doing this changes the recognized polarity of the pedal, resulting in reversed pedal operation. Avoid using the pedals directly on a soft oor, since they may scratch the surface of the oor. Avoid getting caught in or tripping over the pedal cords; this may cause the instrument to fall and result in damage or injury.

Save to a Custom kit.

Press the [ASSIGN] button to save to a Custom kit (the lamp will be off). To cancel the saving, simply press the [KIT], [SONG] or [DEMO] button. After youve assigned the voice, the instrument will automatically be set to the assigned custom kit. You can now play the voice you have assigned to the pad/pedal.
Setting the Reverb ON/OFF
Different depths of the DD-65/YDD-60s reverb effect can be added to the DD-65/YDD-60s overall sound.

Lamp is on

Press the [REVERB] button.
When you press the [REVERB] button the buttons lamp lights, and the ambience of a room or concert hall is added to the sound.
To turn Reverb off, press the [REVERB] button again. (Make sure that the lamp is not lit.)
Setting the Reverb type 1
Enter the Reverb type setting function.
Press the [FUNCTION] button once, then press the [DRUM 1] or [DRUM 2] button a number of times until the rbt item appears. The currently selected Reverb type number appears next to the rbt indication.
Change the reverb type by turning the DIAL.

Reverb type List

No. 5 Reverb Type Hall 1 Hall 2 Hall 3 Room 1 Room 2 No. 10 Reverb Type Stage 1 Stage 2 Plate 1 Plate 2 Off
Press the [FUNCTION] button to exit from the Function mode.
Setting the Pad Sensitivity
The instrument allows you to custom-set the sensitivity of the pads (range 02). When set to a value of 2, the pad sensitivity is the highest, providing the most dynamic range for your playing (softest to loudest volume).
Enter the Pad Sensitivity setting function.
Press the [FUNCTION] button once, then press the [DRUM 1] or [DRUM 2] button a number of times until the SGL item appears. After a while, the current Sensitivity value appears next to the SGL indication.

Set the Sensitivity.

To raise the value, turn the DIAL to the right (clockwise), and to lower it, turn the DIAL to the left (counter-clockwise).

Default value is 1.

Exit from the Function mode by pressing the [FUNCTION] button.
About the Pad Sound Mechanism
Each time you strike a pad, the sensor which is located at the bottom of the pad triggers an electronic signal and makes a drum sound. If you strike a pad too strongly, nearby sensors may also respond to the hit and trigger unwanted sounds. The DD-65/ YDD-60 is set to ignore weak signals from the pads in order to prevent inadvertent, unwanted sounds. However, this may result in problems when intentionally striking two pads simultaneously. If one pad is struck strongly and the other weakly, the pad struck weakly may not sound (even though you want it to). To solve this, you can change the DD-65/YDD-60 settings or alter your playing technique (as described below). Striking two pads simultaneously results in one of the pads not sounding. Set the pad sensitivity level to 2. This may solve the problem if you strike one of the pads weakly. Better yet, take care to strike both pads with equal force. Striking one pad results in other pads also sounding, even though they were not struck. Set the pad sensitivity level to 0. With this setting, pads that are not struck are effectively kept from responding to strong hits on nearby pads.

Setting the Click ON/OFF

The instrument includes a click sound with adjustable tempo and time signature.
Press the [CLICK] button. The click sounds in rhythm at the current tempo. (See Adjusting the Tempo on page 25.) To turn the click off, press the button once again.
Setting the Time Signature of the Click
Setting the numerator of the time signature..
The range is 0 to 16. The rst beat is accented with a bell sound and the rest with clicks.
Enter the numerator value setting function.
Press the [FUNCTION] button once, then press the [DRUM 1] or [DRUM 2] button a number of times until the CL1 item appears. After a while, the current numerator value appears next to the CL1 indication.
Set the numerator value of the time signature.
Default value is 4. When set to 00, the click sounds all beats with a click sound (no accent).
Setting the denominator of the time signature.
Set the basic note value for each measure.
Enter the denominator value setting function.
Press the [FUNCTION] button once, then press the [DRUM 1] or [DRUM 2] button a number of times until the CL2 item appears. After a while, the current denominator value appears next to the CL2 indication.
Set the denominator value of the time signature.
Set the denominator value to one of the values 2 ( ), 4 ( ), 8 ( ), 16 ( ) by using the DIAL.

Default value is 4.

Setting the click volume...
Sets the click volume (range: 1127).
Enter the click volume setting function.
Press the [FUNCTION] button once, then press the [DRUM 1] or [DRUM 2] button a number of times until the CL3 item appears. After a while current click volume will appear next to the CL3 indication.
Set the click volume by using the dial.
Setting Equalization On/Off
When you use the internal speakers, set Equalization to ON (default setting is on). When you use headphones or external speakers, set this to off.
Enter the Equalization setting function.
Press the [FUNCTION] button once, then press the [DRUM 1] or [DRUM 2] button a number of times until the Eq item appears. After a while, the current On/Off setting will appear next to the Eq indication.
Set the Equalizer On/Off.
Turn the DIAL clockwise to set to ON, and turn it counter-clockwise to set it to OFF.
This instrument features 100 different songs (ve demo songs, as well as Rhythm patterns and Fill-in patterns) that can be used to provide accompaniment. (See the Song List on page 40.) U01U05 can also be used to playback songs youve recorded yourself and/or loaded from computer. Refer to the section Transferring Song les to and from a connected computer on page 34 for details. Select one of the songs and listen to it.

Enter the Auto Kit Select function.
Press the [FUNCTION] button once, then press the [DRUM 1] or [DRUM 2] button a number of times until the AtS item appears. After a while, the current On/Off status will appear next to the AtS indication.
Turn Auto Kit Select On/Off.

OFF On

Default setting is ON.

Auto Kit Select on

Original factory setting is on.

Adjusting the Tempo

The song tempo and Click tempo can be set anywhere from 11 to 320 beats per minute. The higher the tempo value, the faster the tempo.
Press the [TEMPO] button.
The current tempo value (11320) appears in the display.

Set the Tempo.

Use the DIAL to select the TEMPO. Turn the DIAL to the right (clockwise) to increase the Tempo value, and turn it to the left (counter-clockwise) to decrease the value.
When both the [SONG] and [TEMPO] buttons are pressed simultaneously, the preset tempo of the currently selected song is automatically applied.
About the Beat Indicator During song playback, the three beat lamps in the display will ash in a specic pattern to help you in keeping the beat.
For a song in 4/4 time at a tempo of 120 bpm:
1st beat 2nd beat 3rd beat 4th beat
Press the [SONG] button to exit from the Tempo setting mode.
The tempo value cannot be changed while the demo is playing or during recording.
Use the pads and pedals to play along with the song accompaniment.
The instrument can play a total of 32 notes simultaneously. That includes notes produced by song accompaniment, pads, foot pedals, and note data received through the MIDI IN jack.

Setting the Track ON/OFF

The instruments song accompaniment consists of 4 tracks: Drum tracks 1, 2, and 3, and the Backing track.
DRUM 1 DRUM 2 DRUM 3 BACKING Bass Drum Snare Drum Cymbal Backing
Pressing a Track button ([DRUM 1], [DRUM 2], [DRUM 3], [BACKING]) will mute (turn off the sound) the corresponding track and its indicator lamp will turn off.

When drum 3 is muted.

Muting DRUM 1, DRUM 2 and DRUM 3 tracks allows you to play along with the song and practice the missing part.
With the Break function, you can liven up songs by adding your own solos or lls, whenever you want. Striking a pad while in the Break mode, the songs accompaniment will be muted until the end of the measure you have nished your ll or solo in.

Transferring Performance Data To and From Another Instrument
By connecting this instrument to other MIDI devices or a computer, the performance data of the instrument can be used on those other MIDI devices or computer, and also the performance data from other MIDI devices and computer can be received and sounded with this instrument. When the instrument is connected with another MIDI device, it transmits/receives performance data.
MIDI transmit MIDI IN MIDI OUT DD-65/YDD-60

MIDI instrument

MIDI OUT MIDI receive

MIDI IN

When the instrument is connected with a computer, it transmits/receives performance data.

MIDI IN USB MIDI OUT

DD-65/YDD-60 A USB-MIDI interface (such as the Yamaha UX16)
A Yamaha UX16 or similar USB-MIDI interface (sold separately) will be necessary for MIDI connection between the instrument and a USB equipped computer. Make sure to purchase a Yamaha UX16 or a quality USB-MIDI interface at a musical instrument store, computer store or electrical appliance store. If you use the UX16 interface, install the driver supplied with the interface on your computer.
When using a computer, special software (sequencer software) is needed.

Local ON/OFF

Local Control determines whether or not notes played on the instrument are sounded by its internal tone generator system; the internal tone generator is active when local control is on, and inactive when local control is off. (on). This is the normal setting in which notes played on the instruments keyboard are sounded by the internal tone generator system. Data received via the instruments MIDI terminal will also be played by the internal tone generator. OFF (off).. With this setting the instrument itself produces no sound (pad or pedal performance), but the performance data is transmitted via the MIDI terminal. Data received via the instruments MIDI terminal will also be played by the internal tone generator.

On NOTE

Normally, this should be set to onsince youll want to hear the sound of the instrument as you play it. However, for external sequencer applications, you may need to set this to off to avoid getting double notes, in which the sounds of the instrument are played twiceonce from the pads and once again by the pad data routed through the sequencer.
Enter the Local On/Off setting function.
Press the [FUNCTION] button once, then press the [DRUM 1] or [DRUM 2] button a number of times until the LCL item appears. After a while, the current On/Off status appears next to the LCL indication.

Turn Local On/Off.

Regardless of the Local ON/OFF setting, the instruments performance data is always sent to the MIDI OUT terminals for transmission to external MIDI devices.
No sound comes from speakers when Local control is set to OFF.
Setting the MIDI Note Number

Each pad and pedal (10 total) can be assigned a specic MIDI note number anywhere from C-2 to G8.
For information on transmit notes and voices, refer to the Drum Map on page 48.
Enter the MIDI Note number setting function.
Press the [FUNCTION] button once, then press the [DRUM 1] or [DRUM 2] button a number of times until the not item appears. After a while, the MIDI note number currently assigned to Pad 1 appears next to the not indication.

not A1

# (sharp)
Select a pad or pedal to be assigned a MIDI Note Number.
Strike any pad to see the currently assigned MIDI note number for the pad in the display. Sharp notes are indicated by a beat lamp on the right side of the display.
Indicates the note number is C#-2
Assign a MIDI Note Number.
To select the desired MIDI note number, turn the DIAL to the right (clockwise) and the MIDI note numbers will increase. Turn the DIAL to the left (counter-clockwise) and MIDI note numbers will decrease.

(C-2) (C#-2) (F#8) (G8)

You can also select the MIDI note number by striking the pad repeatedly. Every time the pad is struck, the value will increase by semitone steps.
When you select a drum Kit or Custom Kit, the MIDI Note Number will be applied to the preset value. If the Auto Kit Select is set to ON and another Song is selected, the MIDI Note Number will be applied to the preset value. MIDI Note Number Auto Selection ON/OFF is automatically turned off when a MIDI Note Number is changed.
MIDI Note Number Auto Selection ON/OFF
Ordinarily, you should keep this function set to on for the instrument (default setting is on). When MIDI Number Auto Selection is on and you strike the pad, the MIDI note number corresponding to the pad (voice) you strike is sent via the MIDI OUT terminal. On the other hand, when MIDI Number Auto Selection is off and you strike the pad, the MIDI note number that youve specically assigned to the pad is sent via the MIDI OUT terminal.
Enter the MIDI Number Auto Selection setting function.
After pressing the [FUNCTION] button, press the [DRUM 1] or [DRUM 2] button a number of times until the Ant item appears. After a while, the current setting (on/off) appears next to Ant.

Transferring song les from a computer...
You can transmit Song les from your computer to your instruments Flash Memory. For details about how to transmit the data using the Musicsoft Downloader application, refer to the Online help topic Transferring Data Between the Computer and Instrument (for unprotected data) of the Musicsoft Downloader.
The Musicsoft Downloader application may not be able to access the instrument in the following cases: During Demo playback During Song playback During recording
Data that can be loaded to the instrument from a computer
Songs Data Song data Format Song data
Use the power adaptor when transferring data. The data can be corrupted if the batteries fail during the transfer. Note that user songs 01 to 05 are commonly used for songs youve recorded and/or loaded. Be careful not to erase your important data. Never turn the power off and never plug/unplug the AC power adaptor during data transmission. Not only will the data fail to be transferred and saved, but operation of the ash memory may become unstable and its contents may disappear completely when the power is turned on or off.

: : : :

5 Songs max (U01U05) 70 Kbytes per song SMF Format 0 ***.MID (MIDI Song)
Close the window to exit from the Musicsoft Downloader and re-enable control of the instrument.
Transferring user song les from the instrument to a computer.
You can transfer the User Songs or loaded Songs from computer stored to the instrument, to a computer by using Musicsoft Downloader. For details about how to transmit Song data using the Musicsoft Downloader application, refer to the Online help topic Transferring Data Between the Computer and Instrument (for unprotected data) in the application. Data that can be transferred to a computer from the instrument

User songs (U01U05)

Preset Song data cannot be transmitted from the instrument. Do not rename the user le on the computer. If you do so, it will not be recognized when transferred to the instrument.
Erasing Transferred Song from the instruments Memory To erase all Memory (including data transferred from a computer), use the Initial Clear function on page 36. To erase specic Songs transferred from the computer, use the Delete function on Musicsoft Downloader.
Backup and Initialization..

Backup

Some internal parameters will be backed up to internal memory even if the power is turned off. You can initialize all internal memory to the default settings or initialize the memory excepting the Songs. Following parameters remain in memory User Songs (including songs loaded from computer) Custom Kit Touch Sensitivity Auto Kit Select ON/OFF Song Volume

No sound comes from the speakers.
The selected voice does not sound when the pad is struck. The desired voice has not been assigned to the pad. Suddenly FL appears and recording is stopped. Song is automatically started when Pad is struck.
The amount of recorded data has exceeded the limit of 10,000 notes. Pad Start is set to ON. Set Pad Start to OFF. (See page 23.)

Drum Voice List

Drum Voice List..

Panel Voice List

Voice No. Voice Name Bass Drum AMB+ Bass Drum Power Open Bass Drum Power Closed Bass Drum Soft Bass Drum Hard Bass Drum Bass Drum 2 Bass Drum H BD Rock BD Gate BD Analog L BD Analog H AnBD Dance-1 AnBD Dance-2 AnBD Dance-3 BD Jazz Bass Drum L Gran Cassa Gran Cassa Mute Snare Soft Power 1 Snare Power 1 Snare Rough 1 Open Rim Power 1 Snare Power 2 Snare Rough 2 Snare H Soft Snare M Snare H Hard Open Rim Shot Snare H Soft 2 Snare M 2 Snare H Hard 2 Open Rim Shot 2 SD Room L SD Room H SD Rock H SD Rock L SD Rock Rim Snare L SD Elec L Analog Snare 1 AnSD Snappy AnSD Q AnSD Ana+Acoustic AnSD OpenRim SD Jazz L SD Jazz M Marching Sn M Marching Sn H Brush Tap Brush Slap Tom Power 6 Tom Power 5 Tom Power 4 Voice No. 99 *100 *101 *102 *103 *104 *105 *106 *107 *108 Voice Name Tom Power 3 Tom Power 2 Tom Power 1 High Tom Mid Tom H Mid Tom L Low Tom Floor Tom H Floor Tom L Room Tom 6 Room Tom 5 Room Tom 4 Room Tom 3 Room Tom 2 Room Tom 1 Rock Tom 6 Rock Tom 5 Rock Tom 4 Rock Tom 3 Rock Tom 2 Rock Tom 1 E Tom 6 E Tom 5 E Tom 4 E Tom 3 E Tom 2 E Tom 1 Analog Tom 6 Analog Tom 5 Analog Tom 4 Analog Tom 3 Analog Tom 2 Analog Tom 1 Jazz Tom 6 Jazz Tom 5 Jazz Tom 4 Jazz Tom 3 Jazz Tom 2 Jazz Tom 1 Brush Tom 6 Brush Tom 5 Brush Tom 4 Brush Tom 3 Brush Tom 2 Brush Tom 1 Hi-Hat Closed Power 1 Hi-Hat Pedal Power Hi-Hat Open Power Hi-Hat Closed Power 2 Hi-Hat Closed Hi-Hat Pedal Hi-Hat Open Analog HH Closed 1 Analog HH Closed 2 Voice No. *109 *110 *111 *162 Voice Name Analog HH Open Analog HH Closed 3 Analog HH Closed 4 Analog HH Open 2 Crash Cymbal Stereo 1 Crash Cymbal Stereo 2 Ride Cymbal Stereo 1 Ride Cymbal Stereo 2 Ride Cymbal Cup Stereo Chinese Cymbal Power Splash Cymbal Power Crash Cymbal 1 Crash Cymbal 2 Ride Cymbal 1 Ride Cymbal 2 Ride Cymbal Cup Chinese Cymbal Splash Cymbal Analog Cymbal Side Stick Power Side Stick Analog Side Stick Hand Clap Sticks Castanet Tambourine 1 Tambourine 2 Finger Snap Vibraslap Conga H Tip Conga H Heel Conga H Open Conga H Mute Conga H Slap Open Conga H Slap Conga H Slap Mute Conga L Open Conga L Mute Conga L Slap Open Conga L Slide Bongo H Open 1 Finger Bongo H Open 3 Finger Bongo H Rim Bongo H Tip Bongo H Heel Bongo H Slap Bongo L Open 1 Finger Bongo L Open 3 Finger Bongo L Rim Bongo L Slap Timbale H Open Timbale L Open Timbale Paila H Timbale Paila L

Default Changed

1 - 16 x

MIDI Implementation Chart

Default Messages Altered

Note Number o 9nH,v=1-127 x 9nH,v=0 x x x
0 - 127 : True voice **************

Velocity

Note ON Note OFF

After Touch

Key's Ch's

Pitch Bend

Control *3 *3 *3 *3 *3 *3 *3

Change

0,6,71,72,73,93 96-97 100-101
x x x x x x x x x o x x x
o o o o o o o o o o o o o
Bank Select Modulation Main Volume Panpot Expression Portament Cntrl Data Entry Sustain Reverb Send Lvl Chorus Send Lvl RPN Inc,Dec RPN LSB,MSB

Prog Change o *4 o *4

o 0 - 127

: True #

x **************

System Exclusive

Common o o *2 x x x x o x Mode 2 : OMNI ON ,MONO Mode 4 : OMNI OFF,MONO o(120,126,127) o(121) o(122) o(123-125) o x o : Yes x : No x x
: Song Pos. : Song Sel. : Tune
System : Clock Real Time: Commands
:All Sound OFF :Reset All Cntrls :Local ON/OFF :All Notes OFF Mes- :Active Sense sages:Reset
Mode 1 : OMNI ON , POLY Mode 3 : OMNI OFF, POLY
NOTE: *1 Value of Pan for each drum pad and foot pedal is not transmitted via MIDI. *2 The DD-65/YDD-60 can accept Start/Stop signals, received via MIDI, by setting the MIDI clock to External. *3 This data is transmitted only when it is contained in the song data. *4 Exclusive <GM System ON> F0H, 7EH, 7FH, 09H, 01H, F7H This message automatically restores all default settings for the instrument, with the exception of MIDI Master Tuning. <MIDI Master Volume> F0H, 7FH, 7FH, 04H, 01H, ll, mm, F7H This message allows the volume of all channels to be changed simultaneously (Universal System Exclusive). The values of mm is used for MIDI Master Tuning. (Values for ll are ignored.) <Reverb Type> F0H, 43H, 1nH, 4CH, 02H, 01H, 00H, mmH, llH, F7H mm : Reverb Type MSB ll : Reverb Type LSB Refer to the Effect Map (page 54) for details.
<Chorus Type> F0H, 43H, 1nH, 4CH, 02H, 01H, 20H, mmH, llH, F7H mm : Chorus Type MSB ll : Chorus Type LSB Refer to the Effect Map (page 54) for details. <DRY Level> F0H, 43H, 1nH, 4CH, 08H, 0mH, 11H, llH, F7H ll : Dry Level 0m : Channel Number *5 Recording to an external sequencer from the DD-65/YDD-60 and playing back the data may result in selection of a different Reverb effect or a different kit. Sending MIDI data from the DD-65/YDD-60 to an external tone generator may result in an unexpected voice, particularly if the tone generator doesnt have the same kind of voice as the DD-65/YDD-60.

Effect map

* If the received value does not contain an effect type in the TYPE LSB, the LSB will be directed to TYPE 0. * The numbers in parentheses in front of the Effect Type names correspond to the number indicated in the display. * By using an external sequencer, which is capable of editing and transmitting the system exclusive messages and parameter changes, you can select the Reverb, Chorus and DSP effect types which are not accessible from the DD-65/YDD-60 panel itself.

REVERB

TYPE MSB 004 005.No Effect (1)Hall1 Room Stage Plate No Effect 08 TYPE LSB 16 (2)Hall2 (6)Stage1 (8)Plate(3)Hall3 (4)Room1 (7)Stage2 (9)Plate19 20

(5)Room2

CHORUS
TYPE MSB 000.068.No Effect Chorus Celeste Flanger No Effect (2)Chorus2 (3)Flanger1 (1)Chorus1 (4)FlangerTYPE LSB 20

Specications

Specications...

Drum Pads

8 pads (125mm x 4, 88mm x 4), Touch Sensitive

Power Consumption

Maximum Polyphony

Power Supply

Adaptor : Yamaha PA-5D, PA-150, or an equivalent recommended by Yamaha (sold separately) Batteries: Six C size, LR14 (R14P), or equivalent batteries (sold separately)

Drum Kits

50 Preset + 3 Custom

Dimensions (WxDxH)

602 x 411 x 180 mm (23-11/16" x 16-3/16" x 7-1/16")

Tracks

4 (DRUM 1/DRUM 2/DRUM 3/BACKING)

Weight

4.5 kg (9 lbs., 15 oz. )

Custom Song

5 Songs (approximately 10,000 notes per song)

Supplied Accessories

Drum Stick x 2, Foot Pedal 1 & 2, Owners Manual

Voices

Drum Voices 254 + phrase 25

Optional Accessories

AC Power Adaptor PA-5D, PA-150, or an equivalent Headphones HPE-150/HPE-30 USB-MIDI interface UX16 Kick Pad KP65* Hi-Hat Controller HH65
* Optional Foot Pedal is necessary when using the optional KP65.

Functions

HAND PERCUSSION ON/OFF, TRACK ON/OFF, TAP START, PAD START, BREAK, A-B REPEAT, DEMO
ASSIGN button, REVERB button, HAND PERC. button, KIT button, CLICK button, SONG button, TEMPO button, PART MUTE DRUM 13, BACKING buttons, FUNCTION button, DEMO button, STANDBY/ON button, REC button, BREAK/TAP button, A-B REPEAT button, START/STOP button, DRUM PAD x 8

LED Display

Song/Drum Kit/Tempo etc.
Specications and descriptions in this owners manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specications at any time without prior notice. Since specications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

Purchased from____________________________________________________________ (Retailer)
YAMAHA CORPORATION OF AMERICA Electronic Service Division 6600 Orangethorpe Avenue Buena Park, CA 90620
KEEP THIS DOCUMENT FOR YOUR RECORDS. DO NOT MAIL!
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de dtails sur les produits, veuillez-vous adresser Yamaha ou au distributeur le plus proche de vous gurant dans la liste suivante.
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgefhrten Niederlassung und bei Yamaha Vertragshndlern in den jeweiligen Bestimmungslndern erhltlich. Para detalles sobre productos, contacte su tienda Yamaha ms cercana o el distribuidor autorizado que se lista debajo.

NORTH AMERICA

CANADA
Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311
THE NETHERLANDS/ BELGIUM/LUXEMBOURG
Yamaha Music Central Europe GmbH, Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, The Netherlands Tel: 0347-358 040
THE PEOPLES REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd. 25/F., United Plaza, 1468 Nanjing Road (West), Jingan, Shanghai, China Tel: 021-6247-2211

U.S.A.

Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A. Tel: 714-522-9011

FRANCE

Yamaha Musique France BP 70-77312 Marne-la-Valle Cedex 2, France Tel: 01-64-61-4000

HONG KONG

Tom Lee Music Co., Ltd. 11/F., Silvercord Tower 1, 30 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: 2737-7688
Yamaha Musica Italia S.P.A. Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771

INDONESIA

PT. Yamaha Music Indonesia (Distributor) PT. Nusantik Gedung Yamaha Music Center, Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: 21-520-2577
CENTRAL & SOUTH AMERICA

MEXICO

Yamaha de Mxico S.A. de C.V. Calz. Javier Rojo Gmez #1149, Col. Guadalupe del Moral C.P. 09300, Mxico, D.F., Mxico Tel: 55-5804-0600

SPAIN/PORTUGAL

Yamaha-Hazen Msica, S.A. Ctra. de la Coruna km. 17, 200, 28230 Las Rozas (Madrid), Spain Tel: 91-639-8888

(class B)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class B digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

OBSERVERA!

Apparaten kopplas inte ur vxelstrmskllan (ntet) s lnge som den ar ansluten till vgguttaget, ven om sjlva apparaten har stngts av.
Entsorgung leerer Batterien (nur innerhalb Deutschlands)
Leisten Sie einen Beitrag zum Umweltschutz. Verbrauchte Batterien oder Akkumulatoren drfen nicht in den Hausmll. Sie knnen bei einer Sammelstelle fr Altbatterien bzw. Sondermll abgegeben werden. Informieren Sie sich bei Ihrer Kommune.

(battery)

ADVARSEL: Netspndingen til dette apparat er IKKE afbrudt,
slenge netledningen siddr i en stikkontakt, som er t endt ogs selvom der or slukket p apparatets afbryder. laitetta verkosta.
VAROITUS: Laitteen toisiopiiriin kytketty kyttkytkin ei irroita koko

(standby)

DD-45/YDD-40 Owners Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, shortcircuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Power supply/AC power adaptor
Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it. Only use the voltage specified as correct for the instrument. The required voltage is printed on the name plate of the instrument. Use the specified adaptor (page 31) only. Using the wrong adaptor can result in damage to the instrument or overheating. Check the electric plug periodically and remove any dirt or dust which may have accumulated on it.

Battery

Always replace all batteries at the same time. Do not use new batteries together with old ones. Do not mix battery types, such as alkaline batteries with manganese batteries, or batteries from different makers, or different types of batteries from the same maker, since this can cause overheating, fire, or battery fluid leakage. Do not tamper with or disassemble batteries. Do not dispose of batteries in fire. Do not attempt to recharge batteries that are not intended to be charged. Keep batteries away from children. If the batteries do leak, avoid contact with the leaked fluid. If the battery fluid should come in contact with your eyes, mouth, or skin, wash immediately with water and consult a doctor. Battery fluid is corrosive and may possibly cause loss of sight or chemical burns. Always make sure all batteries are inserted in conformity with the +/- polarity markings. Failure to do so might result in overheating, fire, or battery fluid leakage. When the batteries run out, or if the instrument is not to be used for a long time, remove the batteries from the instrument to prevent possible leakage of the battery fluid.

Do not open

This instrument contains no user-serviceable parts. Do not open the instrument or attempt to disassemble or modify the internal components in any way. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel.

Water warning

Do not expose the instrument to rain, use it near water or in damp or wet conditions, or place containers on it containing liquids which might spill into any openings. If any liquid such as water seeps into the instrument, turn off the power immediately and unplug the power cord from the AC outlet. Then have the instrument inspected by qualified Yamaha service personnel. Never insert or remove an electric plug with wet hands.
If you notice any abnormality
When one of the following problems occur, immediately turn off the power switch and disconnect the electric plug from the outlet. (If you are using batteries, remove all batteries from the instrument.) Then have the device inspected by Yamaha service personnel. The power cord or plug becomes frayed or damaged. It emits unusual smells or smoke. Some object has been dropped into the instrument. There is a sudden loss of sound during use of the instrument.

Fire warning

Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a fire.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other property. These precautions include, but are not limited to, the following:

Do not connect the instrument to an electrical outlet using a multiple-connector. Doing so can result in lower sound quality, or possibly cause overheating in the outlet. When removing the electric plug from the instrument or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it. Remove the electric plug from the outlet when the instrument is not to be used for extended periods of time, or during electrical storms.

Connections

Before connecting the instrument to other electronic components, turn off the power for all components. Before turning the power on or off for all components, set all volume levels to minimum. Be sure to set the volumes of all components at their minimum levels and gradually raise the volume controls while playing the instrument to set the desired listening level.

Location

Do not place the instrument in an unstable position where it might accidentally fall over. Before moving the instrument, remove all connected cables. When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. Use only the stand specified for the instrument. When attaching the stand or rack, use the provided screws only. Failure to do so could cause damage to the internal components or result in the instrument falling over.

Handling caution

Do not insert a finger or hand in any gaps on the instrument. Never insert or drop paper, metallic, or other objects into the gaps on the panel. Do not rest your weight on, or place heavy objects on the instrument, and do not use excessive force on the buttons, switches or connectors. Do not use the instrument/device or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed. Always turn the power off when the instrument is not in use. Even when the [ ] (Standby/On) switch is turned off, electricity is still flowing to the instrument at the minimum level. When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet. Make sure to discard used batteries according to local regulations. (7)-1

NOTICE

To avoid the possibility of damage to the product, data or other property, follow the notices below. Handling and Maintainance Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio may generate noise. Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components. Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard. When cleaning the instrument, use a soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.

Information

About copyrights Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal use. This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license to use others copyrights. Such copyrighted materials include, without limitation, all computer software, style files, MIDI files, WAVE data, musical scores and sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws. Any violation of copyright has legal consequences. DONT MAKE, DISTRIBUTE OR USE ILLEGAL COPIES. About this manual The illustrations and LED displays as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your instrument. The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.
The serial number of this product may be found on the bottom of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid identification in the event of theft.

Model No. Serial No.

(bottom)
Information for Users on Collection and Disposal of Old Equipment and used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC. By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. [For business users in the European Union] If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. [Information on Disposal in other Countries outside the European Union] These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. Note for the battery symbol (bottom two symbol examples): This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.

Pedal (optional)

(Bass Drum)

Drum Sticks

Since a speaker is built into this instrument, you should be careful to never leave any video tapes, cassette tapes, floppy disks or any kind of magnetic storage media on the paneldoing so may result in data loss or damage to the items. Also avoid using the instrument near a television or computer monitor, since interference may result. Use the sticks with caution. Do not use them for anything other than playing the instrument. Also, to avoid damage or injury, refrain from waving them recklessly or throwing them.

Setting Up

Make all necessary settings below BEFORE turning the power on (page 9).
Before connecting the instrument to other electronic components, turn off the power of all the components. Also, before turning any components on or off, make sure to set all volume levels to minimum (0). Otherwise, electrical shock or damage to the components may occur.

Power Requirements

Although the instrument will run either from an AC power adaptor or batteries, Yamaha recommends use of an AC adaptor whenever possible. An AC adaptor is more environmentally friendly than batteries and does not deplete resources. Using an AC Power Adaptor q Connect the AC adaptor to the power supply jack.
Use the specified adaptor (page 31) only. The use of other adaptors may result in irreparable damage to both the adaptor and the instrument.
Using Batteries q Open the battery compartment cover located on the instruments bottom panel. w Insert six AA size, LR6 or equivalent batteries, being careful to follow the polarity markings on the side of the compartment. e Replace the compartment cover, making sure that it locks firmly in place.
w Plug the AC adaptor into an AC outlet.

Adaptor

AC outlet
Unplug the AC power adaptor when not using the instrument, or during electrical storms. Even when the instrument is turned off, electricity is still flowing to the instrument at the minimum level. When you are not using the instrument for a long time, make sure you unplug the AC power adaptor from the wall AC outlet. NOTE Connecting the AC power adaptor automatically supplies power from the adaptor and overrides battery power, even when batteries are installed.

NOTE Any settings, such as the Custom Kit (page 12), will be restored to the factory default settings when the power is turned off. NOTE While a Demo Song is playing, available operations are limited to adjusting the volume, changing the Demo Songs, and stopping the demo.
The Auto Power Off function can be disabled if you turn the power on by holding the [ blinks for a while. ] (Standby/On) switch for more than 3 seconds; the indication dd
Press the [DEMO] button again to stop the Demo Song.
You can also stop the Demo Song by pressing the [START/STOP] button.

Playing the Pads

Strike the pad with the supplied drum sticks or your hands to play the Drum Voices. When playing the pads with your hands, make sure to turn the Hand Percussion feature on by pressing the [HAND PERC.] button. The volume of the pads sounds responds to your playing; when you play soft the volume is soft, and when you play strongly the volume is loud. The actual loudness of the sound may vary according to which part of the pad is struck.
Setting the Hand Percussion On/Off
You can play the pads of the instrument either with the supplied sticks or with your hands. Press and set the following button when you play the instrument with your hands.
Locking the Panel Buttons
If you perform on the instrument solely with your hands, we recommend that you use this operation to lock the panel buttons. This protects the instrument from being inadvertently changed during your performance.
Press the [HAND PERC.] button to turn Hand Percussion on.
Turn on Hand Percussion (see the left column). Press and hold the [HAND PERC.] button until Lc appears on the display.
The indication on appears on the display, and the pad sensitivity is automatically adjusted for optimum playing by hand. To turn Hand Percussion off, press the [HAND PERC.] button again; oF appears on the display.
NOTE Be sure to strike the pads only with your hands when Hand Percussion is on, since the sensitivity is automatically set to appropriate level for hand playing.
All buttons other than the [HAND PERC.] button are disabled. To unlock the panel buttons, press and hold the [HAND PERC.] button until the Lc is no longer shown on the display.

Magic Tom # 1

Magic Tom
The currently selected Magic Tom number appears on the display.
Use the [ ] and [ ] buttons to select a Magic Tom number.

oF oF 10

Magic Tom Magic Tom
Ten patterns (110) are provided. The indication oF can be selected to turn the Magic Tom function off.

Snare Magic Tom

Play the Pads.
You can add a fill-in by striking Pad 3 repeatedly.
NOTE Magic Tom does not function when the Custom Kit CU is selected.

Setting the Click On/Off

The instrument includes a click sound with adjustable tempo and time signature.
Setting the Time Signature of the Click
The time signature (beat) of the click can be set to 0, 2, 3, 4 or 6. The first beat is accented with a bell sound and the rest with clicks. 0 actually represents a beat of 1 (time signature 1/1), and the click sounds all beats without a bell accent.
Press the [CLICK] button to turn the click on.
The click sounds in rhythm at the current tempo (see Adjusting the Tempo on page 16). To turn the click off, press the [CLICK] button once again.
Press and hold the [CLICK] button.
The current setting value appears on the display.
Use the [ ] and [ ] buttons to set the value of the time signature.
Press the [ ] button to increase the value, and press the [ ] button to decrease the value. Pressing the [ ] and [ ] buttons simultaneously restores the default value.
Release the [CLICK] button to execute the change.
NOTE While a Pattern is played back, the time signature of the click synchronizes to the Pattern. The time signature cannot be set during Pattern playback.
Play Along with a Pattern
This instrument features 50 different rhythm patterns that can be used to provide accompaniment (see the Pattern List on page 19). Play the pads (and the pedal) along with the rhythm accompaniment.
Selecting and Playing a Pattern 1.
Press the [PATTERN] button.
Press the [START/STOP] button to start Pattern playback.

Pattern number

The current Pattern number appears on the display.
Use the [ ] and [ ] buttons to select a Pattern number.
A two-measure count-in plays, and the Pattern starts playing. Try playing the pads (and pedal) along with the Pattern. To stop playback of the Pattern, press the [START/ STOP] button once again.
NOTE You can also use the Tap Start function to start Patterns (page 16).
About the Beat Indicator Pattern numbers increase as the [ ] button is pressed, and decrease as the [ ] button is pressed. Pressing the [ ] and [ ] buttons simultaneously calls up Pattern number 01.

Voice No. 85 96

Pad 1 Snare Hit Snare Hard Open Rim Hard Snare Soft Snare Drum Open Rim Shot Snare Heavy Snare Hard Snare Soft Open Rim Shot Snare Soft Snare Drum Open Rim Shot Snare Rough Snare Hit Snare Hit Open Rim Hard Snare Heavy Analog Snare Drum Analog Snare Open Rim Analog Snare Open Rim Analog Snare Drum Snare Jazz Snare Jazz Low Snare Jazz Snare Jazz Low Snare Jazz Snare Jazz High Snare Jazz Side Stick Side Stick Guiro Short Bongo H Open Conga L Open Cuica Mute Repique Tambourim Slap Timpani D High Tom Crash Cymbal 1 Djembe Slap Hand Clap Castanet Conga H Slap Cajon Slap Darabuka Slap Djembe Slap VoicePerc. Snare Drum Shimedaiko Rooster

Voice No. 84 97

Pad 2 Hi-Hat Closed Hi-Hat Closed Hi-Hat Closed Hi-Hat Closed Hi-Hat Open Hi-Hat Open Hi-Hat Open Hi-Hat Closed Hi-Hat Closed Hi-Hat Closed Hi-Hat Closed Castanet Hi-Hat Closed Hi-Hat Closed Hi-Hat Open Hi-Hat Closed Mid Tom Hi-Hat Closed Analog HH Open Analog HH Closed Analog HH Closed Analog Tom 3 Hi-Hat Closed Hi-Hat Closed Hi-Hat Closed Tom 4 Hi-Hat Closed Side Stick Side Stick Hi-Hat Closed Hi-Hat Closed Guiro Long Bongo L Open Conga L Slide Agogo L Surdo Open Tambourim Open Timpani G Mid Tom Crash Cymbal 2 Shekere Shake Cowbell Claves Conga H Tip Cajon Tip Darabuka Mute Djembe Mute VoicePerc. HH Close Atarigane Dog

Voice No. 82 98

Pad 3 Mid Tom Tom 2 Splash Cymbal Tom 4 Tom 2 Cowbell Floor Tom Low Splash Cymbal Ride Cymbal 1 Tom 3 Tom 3 Tom 1 Timbale L Mid Tom Mid Tom Mid Tom Ride Cymbal 1 Hi-Hat Open Snare Drum Analog Cymbal Analog Tom 1 Analog Tom 2 Tom 3 Tom 2 Tom 4 Ride Cymbal 1 Ride Cymbal 2 Ride Cymbal 2 Tom 4 Tom 4 Tom 2 Timbale H Guiro Short Bongo H Open Agogo H Tambourim Open Cuica Open Timpani C Low Tom Ride Cymbal 1 Shaker Hit Agogo L Tambourine Conga H Open Cajon Low Darabuka Open Djembe Open VoicePerc. Tom Oodaiko Cow

Voice No. 83 99

Pad 4 Crash Cymbal 2 Crash Cymbal 1 Crash Cymbal 2 Tom 2 Crash Cymbal 1 Crash Cymbal 1 Crash Cymbal 1 Crash Cymbal 2 Crash Cymbal 2 Crash Cymbal 2 Splash Cymbal Hand Cymbal Timbale H Crash Cymbal 2 Crash Cymbal 1 Crash Cymbal 2 Crash Cymbal 1 Crash Cymbal 1 Analog Cymbal Analog Snare Drum Crash Cymbal 2 Analog Tom 1 Crash Cymbal 1 Crash Cymbal 1 Crash Cymbal 1 Crash Cymbal 1 Crash Cymbal 2 Ride Cymbal 1 Hi-Hat Closed Crash Cymbal 1 Splash Cymbal Timbale L Guiro Long Bongo L Open Cuica Open Tambourim Slap Cuica Mute Timpani F Floor Tom High Ride Cymbal 2 Wind Chime Agogo H Shaker Conga L Open Shaker Tambourine Shekere Shake VoicePerc. Crash Oodaiko Rim Horse

Voice No. 86 44

Pedal Bass Drum Ambient Bass Drum Bass Drum Bass Drum Hard Bass Drum Kick Gate Bass Drum Ambient Bass Drum Bass Drum Bass Drum Bass Drum Bass Drum Bass Drum Bass Drum Bass Drum Bass Drum Bass Drum Bass Drum Analog Bass Drum 2 Analog Bass Drum 1 Analog Bass Drum 1 Analog Bass Drum 2 Bass Drum Bass Drum Kick Jazz Bass Drum Hard Bass Drum Bass Drum Bass Drum Bass Drum Bass Drum Bass Drum Claves Hand Clap Surdo Open Tom 1 Tom 1 Hand Cymbal Floor Tom Low Splash Cymbal Shaker Shekere Shake Surdo Open Tambourine Tambourine Tom 2 Claves VoicePerc. Bass Drum Kabuki Voice / Tsuzumi Hand Clap

Drum Score

There are many different types of drum score commercially available, but weve chosen the following common format for the examples below.

Hi-Hat (H.H.) Open Close

Hi-Hat Cymbals (H.H.) Ride Cymbal (RIDE)

Crash Cymbal Snare Drum

Snare Drum (Side Stick/ Rim Shot)

High Tom

Mid Tom Low Tom
High Hi-Hat Cymbals (PEDAL) Bass Drum
: Repeat the previous measure. : Repeat the previous two measures. : Eighth notes are to be played with a triplet feel. In this manual some notes appear in parentheses. This indicates that the note is played by the instrument and you do not need to play it.
The following are drum scores for each Pattern, with the Pattern number, Pattern name and the recommended Drum Kit number indicated. (Some of the scores also include the recommended Magic Tom number indicating the space for a fill-in.) Refer to the Drum Kit List (page 20) to see the voice assignments to pads and pedal for each Drum Kit. Try and play along with these Patterns!

8 Beat 1 (Drum Kit 1)

A typical rhythm pattern in rock and pop music based on eighth notes.

8 Beat 2 (Drum Kit 2)

8 Beat 3 (Drum Kit 2)

CRASH H.H.

8 Beat 4 (Drum Kit 3)

8 Beat 5 (Drum Kit 4)

8 Beat 6 (Drum Kit 1)

Rock 1 (Drum Kit 14)

CRASH H.H. Magic Tom 4

Rock 2 (Drum Kit 15)

CRASH H.H. Magic Tom 3

Rockn Roll (Drum Kit 5)

CRASH H.H.Open
Early rock n roll pattern from the 1950s, popularized by Elvis Presley and Chuck Berry and others.

Hard Rock 1 (Drum Kit 6)

Hard Rock 2 (Drum Kit 7)

Hard Rock 3 (Drum Kit 6)

CRASH COWBELL

Blues (Drum Kit 23)

Blues is a genre created by African-Americans in the U.S. and is the musical root for both jazz and rock.

Soul (Drum Kit 24)

Chacha (Drum Kit 32)

TIMBALES
One of the major Cuban rhythms, along with Mambo and Rumba.
Now that you have played through the scores above, continue to play and enjoy the rest of the Patterns in your favorite styles!

Specifications

Size/Weight Dimensions Width Height Depth Weight Control Interface Pad Number of Pads Touch Sensitivity Pedal Display Panel Voices Polyphony Voices Drum Kits Magic Toms Songs Demo Songs Patterns Functions Overall Controls Number of Pedals Type Language Number of Polyphony (Max.) Number of Voices Number of Drum Kits Number of Magic Tom Patterns Number of Demo Songs Number of Patterns Click Tempo Range Miscellaneous Connectivity Connectors DC IN AUX IN PHONES/OUTPUT PEDAL Amplifiers and Speakers Power Supply Amplifiers Speakers Power Supply Adaptor Batteries Power Consumption Accessories Inclulded Accessories 343 mm (13-1/2") 146.1 mm (5-3/4") 325.9 mm (12-13/16") 1.5 kg (3 lbs., 5 oz.) 4 Yes (Hand Percussion On/Off) 1 (optional) LED (7-segment, 2-digit) English 50 Preset + 1 Custom 50 Yes 11280 Auto Power Off, Tap Start, Part Mute 12 V 1 (Mini, Mono) 1 (Mono) 1 5W 12 cm PA-130, PA-3C, or an equivalent recommended by Yamaha Six AA size, LR6 6W (PA-130)/8W (PA-3C) Owners Manual AC Power Adaptor Drum Stick (x2) My Yamaha Product User Registration AC Power Adaptor PA-130, PA-3C, or an equivalent Footswitch FC4/FC5 Headphones HPE-150, HPE-30 Snare Stand SS662

Optional Accessories

Specifications and descriptions in this owners manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
LIMITED 1-YEAR WARRANTY ON PORTABLE DIGITAL DRUMS (DD AND YDD SERIES)
Thank you for selecting a Yamaha product. Yamaha products are designed and manufactured to provide a high level of defect-free performance. Yamaha Corporation of America (Yamaha) is proud of the experience and craftsmanship that goes into each and every Yamaha product. Yamaha sells its products through a network of reputable, specially authorized dealers and is pleased to offer you, the Original Owner, the following Limited Warranty, which applies only to products that have been (1) directly purchased from Yamahas authorized dealers in the fifty states of the USA and District of Columbia (the Warranted Area) and (2) used exclusively in the Warranted Area. Yamaha suggests that you read the Limited Warranty thoroughly, and invites you to contact your authorized Yamaha dealer or Yamaha Customer Service if you have any questions.

Limitation of Implied Warranties and Exclusion of Damages: ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO THE APPLICABLE PERIOD OF TIME SET FORTH ABOVE. YAMAHA SHALL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OR FOR DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE, DAMAGE TO ANY OTHER EQUIPMENT OR OTHER ITEMS AT THE SITE OF USE OR INTERRUPTION OF PERFORMANCES OR ANY CONSEQUENCES. YAMAHAS LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, AT YAMAHAS OPTION. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This is the only express warranty applicable to the product specified herein; Yamaha neither assumes nor authorizes anyone to assume for it any other express warranty.
If you have any questions about service received or if you need assistance in locating an authorized Yamaha Servicer, please contact:
CUSTOMER SERVICE Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, California 90620-1373 Telephone: 800-854-1569 www.yamaha.com
Do not return any product to the above address without a written Return Authorization issued by Yamaha.
c 2009 Yamaha Corporation of America. Effective: 11/01/09
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de dtails sur les produits, veuillez-vous adresser Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgefhrten Niederlassung und bei Yamaha Vertragshndlern in den jeweiligen Bestimmungslndern erhltlich.
Para detalles sobre productos, contacte su tienda Yamaha ms cercana o el distribuidor autorizado que se lista debajo.

NORTH AMERICA

CANADA
Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311
THE NETHERLANDS/ BELGIUM/LUXEMBOURG
Yamaha Music Europe Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, The Netherlands Tel: 0347-358 040
THE PEOPLES REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: 021-6247-2211

FRANCE

Yamaha Musique France BP 70-77312 Marne-la-Valle Cedex 2, France Tel: 01-64-61-4000

U.S.A.

Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A. Tel: 714-522-9011

HONG KONG

Tom Lee Music Co., Ltd. 11/F., Silvercord Tower 1, 30 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: 2737-7688

NORWAY

Norsk filial av Yamaha Scandinavia AB Grini Nringspark 1, N-1345 sters, Norway Tel: 77 70

SINGAPORE

Yamaha Music Asia Pte., Ltd. #03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015 Tel: 747-4374

ICELAND

EUROPE
THE UNITED KINGDOM/IRELAND
Yamaha Music U.K. Ltd. Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, England Tel: 01908-366700
Skifan HF Skeifan 17 P.O. Box 8120, IS-128 Reykjavik, Iceland Tel: 525 5000

TAIWAN

Yamaha KHS Music Co., Ltd. 3F, #6, Sec.2, Nan Jing E. Rd. Taipei. Taiwan 104, R.O.C. Tel: 02-2511-8688

RUSSIA

Yamaha Music (Russia) Office 4015, entrance 2, 21/5 Kuznetskii Most street, Moscow, 107996, Russia Tel: 0660

GERMANY

Yamaha Music Europe GmbH Siemensstrae 22-34, 25462 Rellingen, Germany Tel: 04101-3030

THAILAND

Siam Music Yamaha Co., Ltd. 4, 6, 15 and 16th floor, Siam Motors Building, 891/1 Rama 1 Road, Wangmai, Pathumwan, Bangkok 10330, Thailand Tel: 02-215-2626

OTHER EUROPEAN COUNTRIES

Yamaha Music Europe GmbH Siemensstrae 22-34, 25462 Rellingen, Germany Tel: +49-4101-3030
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH Branch Switzerland in Zrich Seefeldstrasse 94, 8008 Zrich, Switzerland Tel: 044 3878080

OTHER ASIAN COUNTRIES

AFRICA
Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2312

AUSTRIA

Yamaha Music Europe GmbH Branch Austria Schleiergasse 20, A-1100 Wien, Austria Tel: 01-60203900
Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2317
CZECH REPUBLIC/SLOVAKIA/ HUNGARY/SLOVENIA
Yamaha Music Europe GmbH Branch Austria Schleiergasse 20, A-1100 Wien, Austria Tel: 01-602039025

OCEANIA

AUSTRALIA
Yamaha Music Australia Pty. Ltd. Level 1, 99 Queensbridge Street, Southbank, Victoria 3006, Australia Tel: 3-9693-5111

MIDDLE EAST

TURKEY/CYPRUS
POLAND/LITHUANIA/LATVIA/ESTONIA
Yamaha Music Europe GmbH Branch Sp.z o.o. Oddzial w Polsce ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-868-07-57