Owners Manual

SPECIAL MESSAGE SECTION
This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specically recommended by Yamaha. This product should be used only with the components supplied or; a cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is used, please observe all safety markings and instructions that accompany the accessory product. This product may also use household type batteries. Some of these may be rechargeable. Make sure that the battery being charged is a rechargeable type and that the charger is intended for the battery being charged. When installing batteries, do not mix batteries with new, or with batteries of a different type. Batteries MUST be installed correctly. Mismatches or incorrect installation may result in overheating and battery case rupture.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained in this manual is believed to be correct at the time of printing. However, Yamaha reserves the right to change or modify any of the specications without notice or obligation to update existing units. This product, either alone or in combination with an amplier and headphones or speaker/s, may be capable of producing sound levels that could cause permanent hearing loss. DO NOT operate for long periods of time at a high volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an audiologist. IMPORTANT: The louder the sound, the shorter the time period before damage occurs.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all batteries away from children. Dispose of used batteries promptly and as regulated by the laws in your area. Note: Check with any retailer of household type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and federal regulations that relate to the disposal of products that contain lead, batteries, plastics, etc. If your dealer is unable to assist you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model number, serial number, power requirements, etc., are located on this plate. You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent record of your purchase.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a function or effect works (when the unit is operating as designed) are not covered by the manufacturers warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following:
Model Serial No. Purchase Date

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is approximately ve years. When replacement becomes necessary, contact a qualied service representative to perform the replacement.

Panel Logos

GM System Level 1
GM System Level 1 is an addition to the MIDI standard which ensures that any GM-compatible music data can be accurately played by any GM-compatible tone generator, regardless of manufacturer. The GM mark is afxed to all software and hardware products that support GM System Level.

XGlite

As its name implies, XGlite is a simplied version of Yamahas high-quality XG tone generation format. Naturally, you can play back any XG song data using an XGlite tone generator. However, keep in mind that some songs may play back differently compared to the original data, due to the reduced set of control parameters and effects.
USB is an abbreviation for Universal Serial Bus. It is a serial interface for connecting a computer with peripheral Devices. It allows hot swapping (connecting peripheral devices while the power to the computer is on).

STYLE FILE

The Style File Format is Yamahas original style le format which uses a unique conversion system to provide high-quality automatic accompaniment based on a wide range of chord types.
Congratulations and thank you for purchasing the Yamaha DGX-220/YPG-225 Portable Grand! Please read this owners manual carefully before using the instrument in order to take full advantage of its various features. Make sure to keep this manual in a safe and handy place even after you nish reading, and refer to it often when you need to better understand an operation or function.

Accessories

The DGX-220/YPG-225 package includes the following items. Please check that you have them all.
Owners Manual Music rest Accessory CD-ROM

Music Rest

Insert the music rest into the slots as shown.
Special Features of the DGX-220/YPG-225
Play a Variety of Instrument Voices

Page 14

The instrument voice that sounds when you play the keyboard can be changed to violin, ute, harp, or any of an extensive range of voices. You can change the mood of a song written for piano, for example, by using violin to play it instead. Experience a whole new world of musical variety.

Play Along with Styles

Page 19
Want to play with full accompaniment? Try the auto-accompaniment Styles. The accompaniment styles provide the equivalent of a full backing band covering a wide variety of styles from waltzes to 8-beat to euro-trance. and much more. Select a style that matches the music you want to play, or experiment with new styles to expand your musical horizons.

You can also select the Split Voice display by pressing the [FUNCTION] button and then using the CATEGORY [ ] and [ ] buttons to select the S.Voice item.

S.Voice

FngrBass
The currently selected SPLIT voice
Select the desired split voice.
Watch the displayed split voice and rotate the dial until the voice you want to use is selected. The voice selected here becomes the split voice which will play to the left of the keyboard split point. For this example try selecting the 033 Folk Guitar voice.

Folk Gtr

Try selecting and playing a range of split voices.
Play the Grand Piano Voice
When you just want to play piano, all you have to do is press one convenient button.
Press the [PORTABLE GRAND] button.
The 001 Grand Piano voice will be selected.
When you press the [PORTABLE GRAND] button all settings other than touch sensitivity are turned off. The dual and split voices will also be turned off, so only the Grand Piano voice will play over the entire keyboard.
This instrument includes a range of drum kits and unique sound effects you can use for entertainment. Laughter, babbling brooks, jet y-bys, eerie effects, and much more. These sounds can be a great way to enhance the mood at parties.

Drum Kits

Drum kits are collections of drum and percussion instruments. When you select a violin or other normal instrument main voice, for example, all keys produce the sound of the same violin, only at different pitches. If you select a drum kit as the main voice, however, each key produces the sound of a different drum or percussion instrument.
Drum Kit Selection Procedure (refer to steps 1 and 2 on page 14)
1 Press the [VOICE] button. 2 Use the dial to select 117 Std.Kit1. 3 Try out each key and enjoy the drum and percussion sounds!
Try out each key and enjoy the drum and percussion sounds! Dont forget the black keys! Youll hear a triangle, maracas, bongos, drums. a comprehensive variety of drum and percussion sounds. For details on the instruments included in the drum kit voices (voice numbers 117 to 128), see the Drum Kit List on page 104.

Sound Effects

The sound effects are included in the drum kit voice group (voice numbers 127 and 128). When either of these voices are selected you will be able to play a range of sound effects on the keyboard.
Sound Effect Selection Procedure (refer to steps 1 and 2 on page 14)
1 Press the [VOICE] button. 2 Use the dial to select 128 SFX Kit2. 3 Try out each key and enjoy the sound effects!
As you try out the various keys youll hear the sound of a submarine, a telephone bell, a creaking door, laughter, and many other useful effects. 127 SFX Kit1 includes lightning, running water, dogs barking, and others. Some keys do not have assigned sound effects, and will therefore produce no sound. For details on the instruments included in the SFX kit voices, see SFX Kit 1 and SFX Kit 2 in the Drum Kit List on page 104.

When automatic accompaniment is on. The area of the keyboard to the left of the split point (54 : F#2) becomes the auto accompaniment region and is used only for specifying the accompaniment chords.

Split point (54 : F#2)

The keyboard split point can be changed as required: refer to page 65.
Auto accompaniment region

Turn sync start on.

Press the [SYNC START] button to turn the sync start function on.
Flashes when sync start is on.
When sync start is on, the bass and chord accompaniment included in a style will start playing as soon as you play a note to left of the keyboard split point. Press the button a second time to turn the sync start function off.
Play a left-hand chord to start the style.
You can still play chords even if you dont actually know any chords. This instrument will recognize even a single note as a chord. Try playing from one to three notes at the same time to the left of the split point. The accompaniment will change according to the left-hand notes you play. Try this! Scores for some chord progressions are provided on page 22. These examples should help you get a feel for what types of chord progressions sound good with the styles.
Play a variety of left-hand chords while playing a melody with your right hand.
Press the [START/STOP] button to stop style playback when youre done.
You can switch style sections to add variety to the accompaniment. Refer to Pattern Variation (Sections) on page 63.
Styles Are More Fun When You Understand Chords
Chords, created by playing multiple notes at the same time, are the basis for harmonic accompaniment. In this section well take a look at sequences of different chords played one after another, or chord sequences. Since each chord has its own unique coloreven if its different ngerings of the same chordthe chords you choose to use in your chord progressions have a huge inuence on the overall feel of the music you play. On page 20 you learned how to play colorful accompaniments using styles. Chord progressions are vital to creating interesting accompaniments, and with a little chord know-how you should be able to take your accompaniments to a new level. On these pages well introduce three easy-to-use chord progressions. Be sure to try them out with the instruments accompaniment styles. The style will respond to the chord progression you play, effectively creating a complete song.

Select the CHORD type.

Hold for longer than a second Select Chord
Press and hold the [P.A.T. ON/OFF] button for longer than a second. PAT Type appears in the display for a few seconds, then the currently selected performance assistant technology type will be displayed. Select the Chord type by using the dial.
Press the [SONG] button, and the Song Select display appears. Select a song by using the dial. For this example try selecting the 010 Ave Maria.

Using Songs (page 25)

Song name

AveMaria

Song number The song displayed here will be played.
What is a Song? You know the normal meaning of this word, but in this instrument the term Song refers to the data that makes up a complete song. The performance assistant technology features uses the chord and melody data, and should always be used with a song (page 25).
Song playback will begin. The basic pattern will play repeatedly. Listen to the basic pattern for four measures while getting a feel for the basic pattern, then begin playing yourself from the fth measure.

Play on the keyboard.

Before
Try playing the score on the left with both hands. You can even play the same keys over and over: C, E, G, C, E, G, C, E. Youll notice that at measure ve the notes will come out according to the score on the right. Keep playing, and performance assistant technology Chord type will continue to correct the notes that you play. This is the performance assistant technology Chord type. You can stop song playback at any time by pressing the [START/STOP] button.
Press the [P.A.T. ON/OFF] button to turn the performance assistant technology feature off.
The score for Ave Maria is provided on page 96.
CHD/FREE TypeApplying the Chord Type to the Left Hand Only
Select the CHD/FREE type.

CHD/FREE

Hold for longer than a second Select CHD/FREE
Press and hold the [P.A.T. ON/OFF] button for longer than a second. PAT Type appears in the display for a few seconds, then the currently selected performance assistant technology type will be displayed. Select the CHD/FREE type by using the dial.
Press the [SONG] button, and the Song Select display appears. Select a song by using the dial. For this example try selecting the 011 Nocturne.

In this case r1 indicate that right-hand lesson 1 has been selected.

Left-hand part

Right-hand part
(In the case of a right-hand lesson)

Stop the Lesson mode.

You can stop the Lesson mode at any time by pressing the [START/ STOP] button. Once youve mastered Lesson 1, move on to Lesson 2.

See How Youve Done

~~~~~~~~ Excellent Very Good ~~~~~~ ~~~~ Good ~~ OK
When the lesson song has played all the way through your performance will be evaluated in 4 levels: OK, Good, Very Good, or Excellent. Excellent! is the highest evaluation.
After the evaluation display has appeared, the lesson will start again from the beginning.
The evaluation feature can be turned off via the FUNCTION Grade item (page 77).

Lesson 2Your Tempo

Learn to play the correct notes with the correct timing. Song playback tempo will vary to match the speed you are playing at. The song will slow down when you play wrong notes, so you can learn at your own pace.
Select the song and part you want to practice (steps 1 and 2 on pages 36, 37).

Start Lesson 2.

Each time the LESSON [START] button is pressed the lesson modes are selected in sequence: Lesson 1 Lesson 2 Lesson 3 Off Lesson 1.
In this case r2 indicate that righthand lesson 2 has been selected.
Song playback will begin automatically when Lesson 2 is selected.
Play the note shown in the display. Try to play the notes at the correct timing. As you learn to play the right notes at the right timing the tempo will increase until eventually youll be playing at the songs original tempo.
Left-hand part Right-hand part
You can stop the Lesson mode at any time by pressing the [START/ STOP] button. Once youve mastered Lesson 2, move on to Lesson 3.

Lesson 3Minus One

Heres where you can perfect your technique. The song will play at the normal tempo, minus the part you have chosen to play. Play along while listening to the song.

Start Lesson 3.

In this case r3 indicate that righthand lesson 3 has been selected.
Song playback will begin automatically when Lesson 3 is selected.
Play the note shown in the display.
You can stop the Lesson mode at any time by pressing the [START/ STOP] button.

When you execute the Flash Clear operation, song data you have purchased will also be cleared. Be sure to save data you want to keep to a computer.

Basic Operation

Overall DGX-220/YPG-225 control is based on the following simple operations.
1 Press a button to select a basic function. 2 Use the dial to select an item or value. 3 Start a function.

3 Start a function.

1 Select a basic function.

Display (page 52)

2 Select an item or value.

Volume Adjustment

Adjusts the volume of the sound heard via the instruments speakers or a pair of headphones plugged into the PHONES jack.
The Press & Hold Symbol
The symbol that appears next to some buttons indicates that the button can be pressed and held for longer than a second to call up a related function. This provides convenient direct access to a range of functions.
Rotate counterclockwise to lower the volume.
Rotate clockwise to increase the volume.
Press a button to select a basic function.
Select a song you want to listen to or a song you want to use for a lesson.
Select an auto-accompaniment style. Select a voice you want to play on the keyboard.
Use the dial to select an item or value.
When you select a basic function, the item corresponding to that function will be displayed. You can then use the dial or the number buttons [0][9] to select the desired item.
This portion of the display indicates the name and number of the currently selected song, voice and style. It also displays the name and current setting/ value of other functions.

Changing Values

] and [
Rotate the dial clockwise to increase the value of the selected item, or counterclockwise to decrease its value. Rotate the dial continuously to continuously increase or decrease the value.

Decrease Increase

CATEGORY [

] buttons

When selecting a song, style, or voice, you can use these buttons to jump to the rst item in the next or previous category.

[+] and [-] Buttons

Press the [+] button briey to increment the value by 1, or press the [-] button briey to decrement the value by 1. Press and hold either button to continuously increment or decrement the value in the corresponding direction.

The currently selected function will appear in the display.

MasterEQ

Speaker1

2 Press the CATEGORY [

The currently selected master EQ type.
] and [ ] buttons as many times as necessary to select the master EQ type function MasterEQ. MasterEQ will be shown in the display for a few seconds, then the currently selected EQ type will appear.
3 Use the dial to select the desired Master
EQ setting. Five settings are available: 15. Settings 1 and 2 are best for listening via the instruments built-in speakers, setting 3 is for headphones, and settings 4 and 5 are ideal for listening via external speakers.
Basic operation of the Style (auto-accompaniment) feature is described on page 19 of the Quick Guide. Here are some other ways you can play the styles, the style volume adjustment procedure, how you can play chords using the styles, and more.
Pattern Variation (Sections)
The DGX-220/YPG-225 features a wide variety of style sections that allow you to vary the arrangement of the accompaniment to match the song you are playing.

Intro Main A/B

INTRO section This is used for the beginning of the Song. When the intro nishes playing, accompaniment shifts to the main section. The length of the intro (in measures) differs depending on the selected Style. MAIN section This is used for playing the main part of the Song. It plays a main accompaniment pattern, and repeats indenitely until another sections button is pressed. There are two variations on the basic pattern (A and B), and the Style playback sound changes harmonically based on the chords you play with your left hand. Fill-in section This is automatically added before changing to section A or B. ENDING section This is used for the ending of the Song. When the ending is nished, the auto accompaniment stops automatically. The length of the ending (in measures) differs depending on the selected Style.
1 Press the [STYLE] button and then

select a style.

2 Press the [ACMP ON/OFF] button to
turn auto accompaniment on.

Ending

Auto ll
3 Press the [SYNC START] button to turn

synchro start on.

Beat arrows will ash when the synchro start standby mode is engaged Appears when Auto Accompaniment is on.
Synchro Start When the synchro start standby mode is engaged, style playback will begin as soon as you play a chord in the accompaniment range of the keyboard. You can disengage the synchro-start standby mode by pressing the [SYNC START] button again.
4 Press the [MAIN/AUTO FILL] button.
8 Press the [INTRO/ENDING/rit.] button.

MAIN A

The name of the selected section MAIN A or MAIN Bwill be displayed.

Performance data can be transferred between the instrument and the computer (page 80). Files can be transferred between the instrument and the computer (page 82).
The connection procedure is as follows:
1 Install the USB-MIDI driver on your com-
puter. The USBMIDI driver is included on the CD-ROM. Installation of the USB MIDI driver is described on page 85.
2 Connect the USB terminal of the computer
to the USB terminal on the instrument using a standard USB cable (USB cable sold separately).
USB Precautions Please observe the following precautions when connecting the instrument to a computer via a USB cable. Failure to do so can cause the instrument and/or the computer to hang up (freeze), possibly causing corruption or loss of data. If the instrument or computer does hang up, turn the power to both devices off and then on again, and restart the computer.
Wake the computer from a sleep/suspended/standby mode before connecting the USB cable.
The supplied CD-ROM also includes a Musicsoft Downloader application that allows you to transfer song les from your computer to the instruments ash memory. For instructions about how to install Musicsoft Downloader and how to transfer song les, see page 83.
Connect the USB cable to the instrument and computer before turning power to the instrument on. Check the following points before turning the instruments power on or off, and before plugging or unplugging the USB cable. Quit all applications. Make sure that no data transfer is in progress (data is transferred whenever you play on the keyboard or play a song). Allow at least 6 seconds between turning the instruments power on and off, and between plugging and unplugging the USB cable. Directly connect the instrument to the computer using a single USB cable. Do not use a USB hub.
NOTE The Musicsoft Downloader application may not be able to access the instrument in the following cases:
DGX-220/YPG-225 USB cable
During style playback. During song playback.
Transferring Performance Data to and from a Computer
By connecting the instrument to a computer, the instruments performance data can be used on the computer, and performance data from the computer can be played on the instrument. When the instrument is connected with computer, it transmits/receives performance data.
USB terminal USB terminal

DGX-220/YPG-225

NOTE Preset Song data cannot be transmitted from the instrument.
9 To playback a song stored in ash
memory, press the [SONG] button. Use the dial to select the song you want to play, then press the [START/STOP] button to start playback. Style les (les with the.STY extension) can be transferred to Flash memory using the same procedure as described above. Style les transferred to the Flash Memory can be loaded into style number 151 and then played (page 67).
Do not unplug the USB cable during a data transfer. Not only will the data not be transferred and saved, but operation of the memory media may become unstable and its contents may disappear completely when the power is turned on or off.
The backup data, including the ve User Songs is transmitted/ received as a single le. As a result, all backup data will be overwritten every time you transmit or receive. Keep this in mind when transferring data.
Store data can be lost due to equipment malfunction or improper operation. For safety we recommend that you keep a copy of all important data stored on your computer. We recommend that you use a power adaptor rather than batteries when transferring data. The data can be corrupted if the batteries fail during the transfer.
Do not rename the backup le on the computer. If you do so, it will not be recognized when transferred to the instrument.
To Use transferred Songs For Lessons. In order to use songs (only SMF format 0) transferred from a computer for lessons it is necessary to specify which channels are to be played back as the right-hand and left-hand parts.
1 Press the [SONG] button and select the song (036) residing in ash memory for which you want to set the guide track. 2 Press the [FUNCTION] button. 3 Use the CATEGORY [ ] and [ ] buttons to select the R-Part or L-Part item. 4 Use the dial to select the channel you want to play back as the specied right- or left-hand part.
We recommend that you select channel 1 for the right-hand part and channel 2 for the left-hand part.
This CD-ROM is copy-protected. Yamaha makes no representations or warranties with regard to any problems while attempting to copy the CD-ROM or software and cannot be held responsible for the results of attempts to copy the data. The software and this owners manual are the exclusive copyrights of Yamaha Corporation. Use of the software and this manual is governed by the license agreement which the purchaser fully agrees to upon breaking the seal of the software packaging. (Please read carefully the Software Licensing Agreement at the end of this manual before installing the application.) Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the manufacturer. Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this manual and the software. This disk is a CD-ROM. Do not attempt to play the disk on an audio CD player. Doing so may result in irreparable damage to your audio CD player. Future upgrades of application and system software and any changes in specications and functions will be announced separately. The screen displays as illustrated in this owners manual are for instructional purposes, and may appear somewhat different from the screens which appear on your computer.

1 Start the computer and use the Adminis2
trator account to log into Windows 2000. Select [My Computer] [Control Panel] [System] [Hardware] [Driver Signing] [File Signature Verication], and check the radio button to the left of IgnoreInstall all les, regardless of le signature and click [OK]. Insert the supplied CD-ROM into the CDROM drive. A start window will appear automatically. First, make sure the POWER switch on the MIDI device is set to OFF, then use a USB cable to connect the MIDI device to the computer. After making the connections, turn on the power of the MIDI device. The system automatically launches the Found New Hardware Wizard. Otherwise, refer to Troubleshooting in the Accessory CD-ROM Installation Guide section of the Owners Manual. Click [Next]. (Some computers may take a while to display the Wizard window.) Select the radio button for Search for a suitable driver for my device [recommended], then click [Next].
If the Wizard panel informs you that The software you are about to install does not contain a Microsoft digital signature, click [Yes].
ROM drive. A start window will appear automatically. First, make sure the POWER switch on the instrument is set to OFF, then use a USB cable to connect the USB terminal of the computer to the USB connector of the instrument. When the instrument is turned on, the computer automatically displays the Add New Hardware Wizard. Otherwise, refer to Troubleshooting in the Accessory CD-ROM Installation Guide section of the Owners Manual. For Windows Me users, check the radio button to the left of Automatic search for a better driver (Recommended) and click [Next]. The system automatically starts searching and installing the driver. Proceed to Step 8. If the system does not detect the driver, select Specify the location of the driver (Advanced) and specify the CD-ROM drives root directory to install the driver and click [Next]. Execute the installation by following the onscreen instructions and proceed to Step 8.
If you are using Windows Me, skip Step 47.

4 Click [Next]. 5

The window enables you to select the search method. Check the radio button to the left of Search for the best driver for your device. (Recommended). Click [Next]. The window enables you to select a location in which to install the driver. Check the Specify a location box, click Browse., then specify the root directory of the CD-ROM drive and continue the installation. The CD-ROM drive letter may vary depending on your computers conguration. When the system detects the driver on the CD-ROM and is ready for installation, it is shown as a message on the screen. Make sure that the YAMAHA USB MIDI Driver is listed, and click [Next]. The system starts the installation. When installation is complete, a message indicating so appears. Click [Finish]. The driver has been installed.

8. GENERAL

This Agreement shall be interpreted according to and governed by Japanese law without reference to principles of conict of laws. Any dispute or procedure shall be heard before the Tokyo District Court in Japan. If for any reason a court of competent jurisdiction nds any portion of this Agreement to be unenforceable, the remainder of this Agreement shall continue in full force and effect.

3. TERMINATION

This Agreement becomes effective on the day that you receive the SOFTWARE and remains effective until terminated. If any copyright law or provisions of this Agreement is violated, the Agreement shall terminate automatically and immediately without notice from Yamaha. Upon such termination, you must immediately destroy the licensed SOFTWARE, any accompanying written documents and all copies thereof.

9. COMPLETE AGREEMENT

This Agreement constitutes the entire agreement between the parties with respect to use of the SOFTWARE and any accompanying written materials and supersedes all prior or contemporaneous understandings or agreements, written or oral, regarding the subject matter of this Agreement. No amendment or revision of this Agreement will be binding unless in writing and signed by a fully authorized representative of Yamaha.
Problem When the instrument is turned on or off, a popping sound is temporarily produced. When using a mobile phone, noise is produced. Possible Cause and Solution This is normal and indicates that the instrument is receiving electrical power. Using a mobile phone in close proximity to the instrument may produce interference. To prevent this, turn off the mobile phone or use it further away from the instrument. Check that nothing is connected to the PHONES/OUTPUT jack on the rear panel. When a set of headphones is plugged into this jack, no sound is output. Check the Local Control on/off. (See page 80.) Playing keys in the right hand area of the keyboard does not produce any sound. The volume is too soft. The sound quality is poor. The rhythm stops unexpectedly or will not play. The recorded data of the song, etc. does not play correctly. The LCD display suddenly goes dark, and all panel settings are reset. The style or song does not play back when the [START/STOP] button is pressed. When using the Dictionary function (page 70), the keys in the right hand area are used only for entering the chord root and type.
There is no sound even when the keyboard is played or when a song or style is being played back.
The batteries are low or dead. Replace all six batteries with completely new ones, or use the optional AC adaptor.
Is External Clock set to ON? Make sure External Clock is set to OFF; refer to External Clock on page 80. Make sure that the Style Volume (page 76) is set to an appropriate level.

Alphabetical order

A-B Repeat..71 Accessories..7 ACMP...20 Auto Accompaniment Range.20 Auto-Accompaniment.20
Flash Memory.. 28 Foot Switch.. 11 Function... 7577

Grade.. 38

Backup..49
Harmony.. 53 Harmony Type.. 53, 109 Harmony Volume.. 77 Headphones.. 11
CD-ROM...85 Channel Message..79 Chord..2224, 6869 Chord Dictionary..70 Chord Fingering.66 CHORD ROOT.70 CHORD TYPE..70 Chorus...55 Chorus Type..109 Computer...79
Initial Send.. 77, 82 Initialization... 49

Keyboard Out.. 80

Default Setting..75 Delete (Song Track)..48 Delete (User Song).48 Demo..26 Demo Cancel..77 Display..52 Drum Kit..18 Drum Kit List..104 Dual Voice..15 Dual Voice Chorus Level.76 Dual Voice Octave..76 Dual Voice Pan..76 Dual Voice Reverb Level.76 Dual Voice Volume..76
Lesson.. 36 Load SFF... 67 Local... 80 L-Part... 84
Main Voice.. 14 Main Voice Chorus Level.. 76 Main Voice Octave.. 76 Main Voice Pan. 76 Main Voice Reverb Level.. 76 Main Voice Volume.. 76 Master EQ Type.. 62 Measure.. 52 Melody Voice.. 44, 72 Metronome.. 56 MIDI... 78 MIDI Data Format.. 112 MIDI Implementation Chart. 110 Music Database. 42 Music Database List.. 107 Music Rest... 7 Mute... 72
Easy Chords..24 Easy Song Arranger..43 Effect Map..112 Effect Type List..109 External Clock..80 External Song..28

notation.. 52

Synchro Start..20, 63 Synchro Stop...64 System Message..79

One Touch Setting.. 61

Tempo...35 Time Signature (Denominator, Numerator)..56 Touch Response.58 Touch Sensitivity..58 Track..4548 Track Clear..48 Transfer..8284 Transpose...60 Troubleshooting (Installation).90 Troubleshooting (instrument)..92 Tuning...60
Panel Sustain.. 59 PC Mode.. 81 Performance assistant technology. 29 Pitch Bend Range.. 76 Power Adaptor.. 10 Preset Song. 25, 2728
Recording.. 45 Registration Memory.. 73 Remote control.. 81 Repeat... 41 Reverb.. 54 Reverb Type.. 109 R-Part... 84
USB..79 USB MIDI Driver..8889 User Song..45
Save (Panel Setting).. 73 Score.. 9499 SMF (Standard MIDI File). 82 Software Licensing Agreement. 91 Song.. 25 Song Clear.. 48 Song List... 27 Song Memory.. 45 Song Out.. 80 Song Volume.. 71 Specifications.. 113 Split Point.. 16, 65 Split Voice.. 16 Split Voice Chorus Level. 76 Split Voice Octave. 76 Split Voice Pan.. 76 Split Voice Reverb Level. 76 Split Voice Volume.. 76 Standard Chords.. 24 Style.. 1923, 63 Style File... 67 Style List.. 106 Style Out.. 80 Style Volume.. 65 Sustain (Footswitch).. 11 Voice...14 Voice List..100