t Connecting Rod

o Heel
A removable rubber base is attached to the underside of the heel. Remarry the rubber, reveals a strip of Velcro that, provides better grip when the stand is used on carpeted surfaces, etc. If the Velcro does not provide sufficient grip, use the rubber.

HI-HAT STAND

OWNER'S MANUAL

Clutch Bolt

Connecting the rod to the frame secures the footboard to the frame.

y Spikes

Lock Nut Drum Key Bolt w Felt Wing Bolt The spikes prevent the hi-hat stand from sliding forward. The unit is equipped with four spikes, one in each of the front legs rubber feet and two on the frame. Spikes located in the legs rubber feet can be extended by loosening the drum key bolt. Those in the frame can be extended to the preferred length by rotating the bolts clockwise.
!0 The Supplied Soft Case and Sheet
To protect the hi-hat stand's finish from scratches, etc., werecommend that it be placed in the supplied soft case when transporting. Also, please wrap the upper pipe in the supplied sheet.

Introduction

Thank you for purchasing this Yamaha Hi-Hat Stand. In order to obtain maximum performance and longevity from hi-hat stand, please read this Owners Manual thoroughly.

Clutch Nut

u Adjusting Leg Position
The position of the legs (footboard) can be adjusted by loosening bolts A and B, shown in the diagram on the right. After the position has been determined, firmly tighten bolts A and B. Leg

Drum Key Bolt q

e Memory Clamp
After you have determined the height of the hi-hat cymbal, secure the memory clamp at the base assemblys pipe holder to set a memory of the pipes position for future settings. At this time, make sure the memory clamp fits into the pipe holder. Use a drum key to firmly tighten the memory clamp so as to prevent the pipe from slipping during performance. Also, the pipe holder is equipped with a drum key holder. (The drum key is optional.) Memory Clamp

!1 A protective sheet

Footboard (example: HS1100) A protective sheet is applied to the HS1100 to protect the finish.

CAUTION

To prevent the Hi-Hat Stand from coming loose during performance, tighten all securing bolts and adjustment bolts firmly. To maintain smooth action, apply some grease-grade oil (ex. lithium grease) to all of the moving parts as needed.
i Adjust the Footboard Angle
The angle adjuster can be used to increase or decrease the amount of footboard angle by raising or lowering the adjuster. With a drum key, loosen the two bolts on either side of the angle adjuster then slide the angle adjuster higher or lower as needed. After the angle has been determined, firmly tighten two bolts with a drum key. Protect Sheet
* Specifications and design are subject to change without notice. Note) Moving parts require occasional lubrication for smooth operation. Also, over tightening of the nylon clutch inside the base assemblys pipe holder may result in damage. Please use caution.

Pipe Holder

q Cymbal Support Plate
To attach the bottom hi-hat cymbal first, remove the hi-hat clutch and set the bottom hi-hat cymbal on the rubber washer. At this time, make sure that the metal plate and the rubber washer are on the cymbal support plate. Rotate the knurled head bolt, located under the plate, to adjust the angle of the cymbal then secure with the fixing nut. Rubber Washer Metal Plate
r Spring Tension Adjustment
The large adjustment dial adjusts spring tension. Turning the dial to the left increases tension while turning to the right decreases tension. Also, this system is equipped with a tension indicator that conveniently displays the amount of tension. Angle Adjuster

HS1100

Hi-Hat Clutch Hi-Hat Shaft Fixing Nut Fixing Nut Knurled Head Bolt

HS1000

Hi-Hat Clutch

HS950

Cymbal Support Plate
Hi-Hat Shaft Cymbal Support Plate
Hi-Hat Shaft Cymbal Support Plate Fixing Nut Knurled Head Bolt
Cymbal Support Plate Knurled Head Bolt
Fixing Nut Knurled Head Bolt

Memory Clamp

Memory Clamp Base Assembly Pipe Holder Bolt A Indicator Adjustment Dial Bolt A Indicator Adjustment Dial Angle Adjuster Bolt B Bolt B
Memory Clamp Base Assembly Pipe Holder Bolt A Indicator Adjustment Dial Angle Adjuster Bolt B Footboard

w Hi-Hat Clutch (LC-930)

The top hi-hat cymbal is fixed and held in place between the two felts of the hi-hat clutch.
Base Assembly Pipe Holder

(Procedure)

1) Loosen the drum key bolt q on the clutch nut and remove the clutch nut from the clutch bolt. 2) Remove the lower felt and place the cymbal between the upper felt and the lower removed felt. 3) Firmly tighten the clutch nut onto the clutch bolt. Next, tighten the drum key bolt q to lock the clutch nut. Since the drum key bolt q can be locked with a minimum of force, be sure not to over tighten which may cause damage to the bolt. 4) The lock nut adjusts the amount of pressure used to hold the cymbal in place. Loosen the drum key bolt w and raise or lower the lock nut to adjust the position. After the position has been determined, tighten the drum key bolt w to lock the lock nut in place. The drum key bolt w can be locked with a minimum of force so be sure not to over tighten which may cause damage to the bolt.

Angle Adjuster

Footboard

Spikes

Printed in Japan

HI-HAT STAND

HS840/HS740

OWNER'S MANUAL

r Spring Tension Knob
The Spring Tension Knob supplies tension control over a 11-step range, To increase tension, slide the Spring Tension Knob up (Fig. A) to any position you like (use the scale as a reference) and then rotate the knob to the left to lock in place. (Fig. B) To reduce tension, rotate the Spring Tension Knob to the right (Fig. C) and slide to any position you like. To increase tension, slide the Spring Tension Knob up, to decrease tension, slide the Spring Tension Knob down. Spring Tension Adjustment

Introduction

Thank you for purchasing a Yamaha Hi-Hat Stand. Please read this owner's manual thoroughly before use.
t Footboard Stabilizer Rod
The Footboard stabilizer rod should attach to holes in the frame at the bottom of the hi-hat base.

Spring Tension Knob

(Fig.A)

(Fig.B)

(Fig.C)

y Spur

The large heavy-duty rubber feet prevent unwanted movement of the hi-hat stand during playing conditions. To minimize slippage further, there are two spurs in the frame. These spurs can be extended as needed by adjusting the turn screws provided on either side of the frame base.
Hi-Hat Shaft Hi-Hat Clutch Cymbal Support Plate

CAUTION

To prevent the Hi-Hat Stand from coming loose during performance, tighten all securing bolts and adjustment bolts firmly. To maintain smooth action, apply some grease-grade oil (ex. lithium grease) to all of the moving parts as needed.
u Leg Position Adjustment

q Cymbal Support Plate

To install the bottom hi-hat cymbal, remove the hi-hat clutch assembly and place the cymbal on the felt washer on the cymbal support plate. The angle of the bottom cymbal can be adjusted by turning the angle bolt on the underside of the support plate. To adjust the angle of the hi-hat cymbal, use the Knob Bolt located on the underside of the cymbal support.

Leg Foot Board

Loosen Bolts A and B shown in the illustration to the right to change the position of the legs (footboard). After the position has been determined, tighten both Bolts A and B firmly. Also, we recommend that the legs be positioned in the same manner as shown in the illustration on the left so as to leave some space available for setup and to provide sufficient stability for the stand. (This setup is for right-handed drummers. For left-handed drummers, please set up in an opposite manner.)

Knob Bolt

Position Clamp Extender Base

w Hi-Hat Clutch

To install the top hi-hat cymbal, loosen the wing bolt and remove the entire hihat clutch assembly from the upper pull rod. Next, remove the clutch nut and position the cymbal between the two clutch felts. After installation, tighten the clutch nut on to the clutch assembly to secure the cymbal. Place the entire assembly onto the hi hat upper pull rod and tighten the wing bolt to secure the desired position of the top cymbal. The lock nuts on the top of the clutch can adjust the feel and sound of the hi hat cymbals. To obtain a loose sound, open the nuts off of the felt; for a tight sound, close the nuts onto the felt. Once the desired sound has been obtained, tighten firmly the lock nuts onto each other.
Note: To maintain smooth action, occasionally apply some grease-grade oil to all of the moving parts. Be careful not to use excessive force when tightening the extender base nut as this may damage the nylon bushing inside the tube. Cymbal Support Plate
Felt Fiber Clutch Bolt Wing Bolt Lock Nut Felts

Hi-Hat Clutch

Footboard Spur Footboard Stabilizer Rod

e Position Clamp

Once the bottom hi-hat cymbal height has been decided, the position clamp can be used to mark the settings for future set ups and to prevent unintentional changes during musical performances. Use a drum key to firmly tighten the position clamp into place.

Cymbal Support Plate

Clutch Nut
* This product photograph is HS840.
* Specifications and design are subject to change without notice.

Printed in Indonesia