Natural Sound 2-way Acoustic-suspension Speaker System
Thank you for selecting this Yamaha NS-10MM speaker system.

NS-10MM

s TO MOUNT THE SPEAKERS ON A WALL Attach the provided mounting bracket to the rear of the speaker by using the provided screws.

PRECAUTIONS

Read these precautions carefully before using your speaker. Any time you note distortion, reduce the volume control on your amplifier to a lower setting. Never allow your amplifier to be driven into clipping. Otherwise the speaker may be damaged. When using an amplifier with a rated output power higher than the nominal input power of the speaker, care should be taken never to exceed the speakers maximum input. Do not attempt to clean the speaker with chemical solvents as this might damage the finish. To clean, wipe with a dry, soft cloth. To prevent the enclosure from warping or discoloring, do not place the speaker where it will be exposed to direct sunlight or excessive humidity. Do not place the speaker where it is liable to be knocked over or struck by falling objects. Stable placement will also ensure better sound performance. Placing the speaker on the same shelf or rack as the turntable can result in feedback. This speaker system is designed for home use only. Never use this speaker system inside a car. Secure placement or installation is the owners responsibility. YAMAHA shall not be liable for any accident caused by improper placement or installation of the speaker.
Remove the provided pads from the paper, and put the pads at both ends on the lower side of the speaker.

PLACING THE SPEAKERS

s TO STAND THE SPEAKERS Place the speakers on a sturdy, vibration-free surface. If you cannot obtain good bass quality when the speakers are placed directly on the floor, insert a block etc. between the speakers and the floor. Better stereo images will be obtained when the speakers are slightly angled in towards the listeners.
Fasten screws into a firm wall or wall support as shown in the diagram, and hang the holes of the mounting bracket on the protruding screws.
Diam. mm Min. 12 mm 2 mm Tapping screw (Available at a hardware store) Wall or wall support 40 mm
Make sure that the screws are caught by a narrow part of the holes securely.
Note Because this speaker is not a magnetic shielding type, there may be some influence on a TV picture depending on the type of TV or the placement of the speaker. In such a case, place the speaker apart from the TV so that there is no influence on TV picture.
WARNING: * Each speaker weighs 1.5 kg (3 lbs. 5 oz.). Do not mount them on thin plywood or soft wall surface material, as the screws may come out of the flimsy surface, causing the speakers to fall down and be damaged, or result in personal injury. * Do not fasten the speakers to wall with nails, adhesives, or other unsound hardware. Long-term use and vibrations may cause them to fall down. * To avoid accidents resulting from tripping over loose speaker cables, fix them to the wall.
CONNECTION TO YOUR AMPLIFIER
BEFORE MAKING CONNECTIONS, MAKE SURE THAT THE AMPLIFIER IS SWITCHED OFF. s CONNECTIONS Connect the push-type input terminals at the rear of the speakers to the speaker output terminals of your amplifier with the provided speaker cables. One side of the speaker cable is marked by a blue line. Connect the (+) terminals on both the amplifier and the speakers using this blue-marked side. Connect the () terminals on both components using the unmarked side of the cable. Connect one speaker to the left (marked L) terminals of your amplifier, and another speaker to the right (marked R) terminals, making sure not to reverse the polarity (+, ). If one speaker is connected with reversed polarity, the sound will be unnatural and lack bass.

REMOVING THE FRONT COVER

The front cover is fastened to the enclosure at four points, and can be removed if desired. To remove the cover, hold on to both sides and slowly pull straight away from the speaker. To reattach, line up the four holes on the inside surface of the cover with the four corresponding pegs on the speaker and push gently.
Note When the cover is removed, take care not to touch the speaker units with your hands or to exert excessive force with tools.
Procedures: Press the tab on the terminal down, as shown in the figure. Insert the bare speaker wire end properly into the terminal hole. [Remove approx. 5 mm (1/4) insulation from the speaker cable.] Remove your finger from the tab to allow it to lock snugly on the cables wire end. Test the security of the connection by tugging lightly on the cable at the terminal. Blue line

You can also use the screw holes on the bottom of the speaker for installing the speakers (if you not use the provided mounting brackets). A screw with a diameter of 4 mm and a pitch of 0.7 mm can be used. (Depth of hole : 8mm)

Speaker (R)

Speaker (L)

SPECIFICATIONS

Type..2-way acoustic-suspension speaker system Speaker Unit...9 cm cone woofer 2.5 cm tweeter Input Terminal...Push-type Nominal Impedance...6 ohms Frequency Response..100 Hz 20 kHz Nominal Input Power..40W Maximum Input Power..100W Sensitivity...88 dB/w/m Crossover Frequency...5 kHz Dimensions (WxHxD).107 x 191 x 140 mm (4-3/8 x 7-1/2 x 5-1/2) Weight...1.5 kg (3 lbs. 5 oz.) Accessories..Speaker cable (10m) x 2 Mounting bracket x 2 Screw x 4 Pad x 4

Blue line

Speaker output terminals of the amplifier
Note Do not let the bare speaker wires touch each other as this could damage the speaker and/or the amplifier.
* Specifications subject to change without notice due to product improvements. * Care should be taken not to exceed the input power values noted above.

VU 94700

AV-IT NEWS RELEASE
NS-10MMF 2-Way Bass-Reflex Tower Speaker System
Yamaha Introduces the NS-10MMF 2-Way Bass-Reflex Tower Speaker System Featuring Powerful Bass Response. Yamaha Corporation announces the release of a new high performance speaker system in its NS-10MM Series. The NS-10MMF is a tower-type, floor-standing speaker system that provides extremely high sound quality for both stereo and home theater use. Utilizing a 2-way, bass-reflex design with dual woofers, the NS-10MMF delivers extra-powerful bass output. Its tall, slim profile and handsome finish give it an impressive appearance with or without the grille, and it includes magnetic shielding for placement near a TV or other monitor. It offers excellent sound quality for stereo music listening, and makes an ideal combination with other Yamaha NS-10MMF Series speakers for 6.1-channel or 5.1-channel home cinema systems.
NS-10MMF Main Features Excellent sound quality with stereo music sources. Ideal combination with Yamaha NS-10MM Series speakers for 6.1channel and 5.1-channel movie sound. Dual woofer design delivers deep, powerful bass. Bass Anchor provides stability, dampens vibrations. Magnetic shielding allows placement near a TV/monitor.
NS-10MMF NEW PRODUCT BULLETIN
2-Way Bass-Reflex Tower Speaker System

NS-10MMF

High quality tower speaker system that delivers clear, accurate reproduction of both music and movie sound. Dual woofer design means extra-powerful bass. An attractively impressive addition to any home cinema or music room.
The NS-10MMF is also offered with a black and cherry finish in some areas.
Tower-Type, Floor-Standing Speaker System with Superb Sound Quality for Music and Home Cinema Enjoyment

1/2 (W)

Clear Sound, Powerful Bass and Impressive Appearance A Great Choice for a High Quality Home Cinema System.
Excellent sound quality with stereo music sources. Ideal combination with Yamaha NS10MM Series speakers for 6.1channel and 5.1-channel movie sound. Dual woofer design delivers deep, powerful bass. Bass Anchor provides stability, dampens vibrations. Magnetic shielding allows placement near a TV/monitor.
but the lower woofer has a six-layer wound voice coil for a more voluminous lower range. Increasing the number of voice coil windings increases drive power while lowering the lowest oscillation frequency (fo), achieving heavy bass reproduction relative to woofer size. Ideal Combination for Home Theater System Combined with the other speakers in the NS-10MM Series, these speakers will deliver exceptional 6.1channel and 5.1-channel movie sound. In addition, they are ideal for use with Yamaha Digital Home Cinema Receivers. Team them with the RX-V730 (RDS) or RXV630 (RDS) for a 6.1-channel system or with the RXV530 (RDS) or RX-V430 (RDS) for a 5.1-channel system. NS-10MMF Main Specifications 2-Way Bass-Reflex Design Dual 9cm Woofers and 2.2cm Balanced-Dome Tweeter Magnetic Shielding Input Power (Max/Nominal): 200 W/70 W Frequency Response: 5535,000 Hz Sensitivity: 86 dB/2.83 V/m Crossover Frequencies: 6 kHz Impedance: 6 ohms Dimensions (W x H x D): 179 x 899 x 234 mm/unit Weight: 9.8 kg/unit
Slim, Floor-Standing Design Delivers High Sound Quality The height and position of the speaker drivers were carefully tested, and the cabinet space used to maximum efficiency, in order to produce rich, deep, low frequency response. The Bass Anchor uses five steel plates to provide stable support and also dampen vibrations that can adversely affect sound quality. Dual Woofer Design for Powerful Bass If you want to hear the full effect of explosions and other bass sounds in your movies, youll love the NS10MMF, thanks to its dual woofer design. The top woofer uses a conventional two-layer wound voice coil,
For details please contact:
Dolby Digital and Double D are trademarks of Dolby Laboratories Corporation. DTS, ES and DTS Digital Surround are trademarks of Digital Theater Systems, Inc. Product designs and specifications are subject to change without notice.