NOTICE:

Service charges incurred due to a lack of knowledge relating to how a function or effect works (when the unit is operating as designed) are not covered by the manufacturers warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your dealer before requesting service.
Model Serial No. Purchase Date

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is approximately ve years. When replacement becomes necessary, contact a qualied service representative to perform the replacement.

PLEASE KEEP THIS MANUAL

92-BP (bottom)
PSR-E323/YPT-320 Owners Manual

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit OFF and ON, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line lter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to
comply with the requirements listed in FCC Regulations, Part 15 for Class B digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/ uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

(class B)

PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, re or other hazards. These precautions include, but are not limited to, the following:
Power supply/AC power adaptor
Only use the voltage specied as correct for the instrument. The required voltage is printed on the name plate of the instrument. Use the specied adaptor (PA-130 or an equivalent recommended by Yamaha) only. Using the wrong adaptor can result in damage to the instrument or overheating. Check the electric plug periodically and remove any dirt or dust which may have accumulated on it. Do not place the AC adaptor cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it.

Water warning

Do not expose the instrument to rain, use it near water or in damp or wet conditions, or place containers on it containing liquids which might spill into any openings. If any liquid such as water seeps into the instrument, turn off the power immediately and unplug the power cord from the AC outlet. Then have the instrument inspected by qualied Yamaha service personnel. Never insert or remove an electric plug with wet hands.

Fire warning

Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a re.

Do not open

Do not open the instrument or attempt to disassemble the internal parts or modify them in any way. The instrument contains no user-serviceable parts. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualied Yamaha service personnel.

Do not use the instrument/device or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician.

Saving data

Saving and backing up your data
Some data items (page 41) are automatically saved as backup data in the internal memory even if you turn the power off. Saved data may be lost due to malfunction or incorrect operation. Save important data to external device such as a computer.
Yamaha cannot be held responsible for damage caused by improper use or modications to the instrument, or data that is lost or destroyed.
Always turn the power off when the instrument is not in use. When using a power adaptor, even when the power switch is in the STANDBY position, electricity is still owing to the instrument at the minimum level. When you are not using the instrument for a long time, make sure you unplug the AC power adaptor from the wall AC outlet. Make sure to discard used batteries according to local regulations.
The illustrations and LCD screens as shown in this owners manual are for instructional purposes only, and may appear somewhat different from those on your instrument.

COPYRIGHT NOTICE

This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license to use others copyrights. Such copyrighted materials include, without limitation, all computer software, style les, MIDI les, WAVE data, musical scores and sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws. Any violation of copyright has legal consequences. DONT MAKE, DISTRIBUTE OR USE ILLEGAL COPIES. Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal use.

Trademarks

Windows is the registered trademarks of Microsoft Corporation. The company names and product names in this Owners Manual are the trademarks or registered trademarks of their respective companies.

Formats and functions

GM System Level 1: GM System Level 1 is an addition to the MIDI standard which ensures that any
GM-compatible music data can be accurately played by any GM-compatible tone generator, regardless of manufacturer. The GM mark is afxed to all software and hardware products that support GM System Level.

XGlite: As its name implies, XGlite is a simplied version of Yamahas high-quality XG tone generation format. Naturally, you can play back any XG song data using an XGlite tone generator. However, keep in mind that some songs may play back differently compared to the original data, due to the reduced set of control parameters and effects. Style File: The Style File Format combines all of Yamahas auto accompaniment know-how into a single unied format.
Stereo Sampled Piano: The instrument has a special Portable Grand Piano Voicecreated by state-ofthe-art stereo sampling technology and using Yamahas sophisticated AWM (Advanced Wave memory) tone generation system.
Yamaha Education Suite 5: The instrument features the new Yamaha Education Suitea set of learning
tools that utilize the latest technology to make studying and practicing music more fun and fullling than ever before!
Touch Response: The exceptionally natural Touch Response feature, with a convenient front panel on/off
switch, gives you maximum expressive level control over the voices.

Supplied Accessories

The PSR-E323/YPT-320 package includes the following items. Please check that you have them all.
Music rest Owners manual (this book)
My Yamaha Product User Registration
* The PRODUCT ID on the sheet will be needed when you ll out the User Registration form.
What You Can Do With the PSR-E323/YPT-320

Playing

Changing Voices

> pages 12, 13

The instrument Voice that sounds when you play the keyboard can be changed to violin, ute, harp, or any of an extensive range of voices. You can also restore the piano settings with a simple press of a button.
Adding Reverb to the sound

>page 43

The reverb effects add a warm ambience to the sound, simulating the complex reections of actual performance spaces, such as a concert hall or small club.
Play along with the Styles

>page 18

You can select from 100 different styles (auto accompaniment) for playing along on the keyboard giving you the equivalent of a full backing band, covering a wide variety of styles from waltzes to 8beat to euro-trance. and much more.

Front Panel

q e w r t

Rear Panel

@9 MIDI IN/OUT terminals..page 58 #0 SUSTAIN jack..page 9 #1 PHONES/OUTPUT jack...page 9 #2 DC IN 12V jack..page 8
Voice List (page 64) Display (page 27) Song List (page 72)
Music Database List (page 71)

Style List (page 70)

GrandPno

o !0 !1

@4 @5 @6 @7

Changing the Voices

This instrument features a variety of realistic, built-in voices. The grand piano Voice is automatically selected whenever the power is turned on, but you can easily change this guitar, drum, or any of an extensive range of voices.

Grand Piano Voice

Try playing a variety of instrument Voices
Press the [VOICE] button.
The Voice number and name are displayed.

Voice number Voice name

Select a Voice.
Select the desired Voice by using the number buttons [0][9], [+], [-]. Refer to the Voice List on page 64.
The Voice shown here becomes the Main Voice for the instrument.

Play the keyboard.

Try selecting and playing different Voices.
Playing the Grand Piano Voice
When you simply want to play a piano Voice, all you have to do is press one convenient button.
Press the [PORTABLE GRAND] button.
The Voice Grand Piano will automatically be selected as the Main Voice.

Metronome

Percussion and drum icons

Using the Metronome

The instrument features a built-in metronome (a device that keeps an accurate tempo) that is convenient for practicing.
Press the [METRONOME] button to start the metronome. To stop the metronome, press the [METRONOME] button again.
If you want to adjust the metronome tempo, press the [TEMPO/ TAP] button to call up the Tempo setting in the display, then press the [+] button to raise the tempo, or press the [-] button to lower it. You can also set the tempo using the number buttons on the front panel.
You can set the time signature (page 48).

Current Tempo value

Playing the Drum Kit Voice
When Voice number 109 (Drum Kit) is selected in step 2 on page 13, you can play different percussion sounds directly from the keyboard. To check which percussion sounds are assigned to each key when you select Voice number 109, look at the icons printed above the keys. You can select and play the desired Drum Kit from 12 preset Drum Kits (Voice number 109121). Details on the instruments and key assignments of each Drum Kit can be found in the Drum Kit List on page 68.
This instrument has 102 built-in Songs. For this instrument, the term Song refers to the data that makes up a piece of music. Listening to a Song.
Select and Listen to a Specic Song

Press the [SONG] button.

For users who are new to chords, this chart features common chords. Since there are many useful chords and many different ways to use them musically, refer to commercially available chord books for further details.
indicates the root note. Major Minor Seventh Minor Seventh Major Seventh
Inversions can be used as well as in root positionwith the following exceptions: m7, m7b5, 6, m6, sus4, aug, dim7, 7b5, 6(9), sus2 Inversion of the 7sus4 and m7(11) chords are not recognized if the notes are omitted. sus2 chords are indicated by the root name only.

Easy Chords

This method lets you easily play chords in the accompaniment range of the keyboard using only one, two, or three ngers.

For root C

To play a major chord Press the root note () of the chord.
To play a minor chord Press the root note together with the nearest black key to the left of it.
To play a seventh chord Press the root note together with the nearest white key to the left of it.
To play a minor seventh chord Press the root note together with the nearest white and black keys to the left of it (three keys altogether).
Basic Operation and Displays

Basic Operation

Press a button to select a basic function: Voice, Song or Style.

3 Start a function.

Display (page 27)

1 Select a basic

function.

2 Select an item or

value.
Press the [SONG] button to access the SONG functions (printed above the buttons), and press the [STYLE] button to access the STYLE functions (printed below).
Number buttons [0][9] The number buttons can be used to directly enter a Song, Style or Voice number or parameter value. For numbers that start with one or two zeroes, the rst zeroes can be omitted.
Example: Selecting Voice 002, Bright Piano. Press number buttons [0], [0], [2].
The Press & Hold Symbol Buttons having this indication can be used to call up an alternate function when the relevant button is pressed and held. Hold down this button until the function calls up. 26
[+], [-] buttons Press the [+] button briey to increase the value by 1, or press the [-] button briey to decrease the value by 1. Press and hold either button to continuously increase or decrease the value in the corresponding direction.

Press briey to decrease.

Press briey to increase.

Display

The Main display shows all of the current basic settings for Song, Style and Voice. It also includes a range of indicators that show the on/off status for various functions.

Flashes

Accompaniment cannot be turned on or off once the [REC] button is pressed.
After youve selected the desired User Song for recording, you can select a Style to be recorded as well. To do this, press the [STYLE] button and select the Style number while the ACMP indication is on. You can turn off the Record mode by pressing the [REC] button again ( and stop ashing).
If all User Songs (Song numbers 103107) contain recorded data, Song 103 will automatically be selected. In this case, you will record over and erase any previous data in Song 103, so be careful that you wont be erasing any material you want to keep!
By playing keys to the left of the Split Point when the Auto Accompaniment is set to on, the Style starts sounding and is recorded with your performance. When Auto Accompaniment is set to off, only your keyboard performance is recorded.
Start recording. When you play the keyboard, recording will begin.
Stop recording. Pressing the [START/STOP] button stops recording and writes the data to the User Song. (A Writing! message is shown.)
To playback the newly recorded performance, press the [START/ STOP] button. In order to record with the Style, turn the Auto Accompaniment to on (see Step 4 on page 20), and then record according to the instructions.

(The ACMP ON lights.)

Never attempt to turn the power off when a Writing! message is shown in the display. Doing so can damage the ash memory and result in a loss of data.
In order to record only your performance, turn the Auto Accompaniment to off and record according to the normal steps.

(The ACMP ON is unlit.)

Use the Musicsoft Downloader to backup the User Songs to a computer (page 60).
Recording to a specied track
The User Songs are organized into two tracks: Track 1 and Track 2. You can specify the track you want to record to.

About track recording

If you start recording by specifying a track, the track will be overwritten (existing data in the track is deleted and replaced with the new recording).

User Song

Data that can be recorded to Track 2
Style playback* (including chord changes) or your own keyboard performance

Start recording Perform steps 2 and 3 on pages 3738. By playing keys to the left of the Split Point when the Auto Accompaniment is set to on, the Style starts sounding and is recorded. Only your performance is recorded by playing the keyboard (any key is OK) when the Auto Accompaniment is set to off.
Flashes when track 2 is selected for recording.

Deleting User Songs

Deleting an entire User Song.
You cannot delete a specic track from a User Song.
Press the [SONG] button and select the User Song you want to delete by using the number buttons [0][9], [+], [-].
Press and hold the [REC] button for longer than a second. The Song Delete display appears.
Hold for longer than a second.

ClrUser1

You can cancel the delete operation by pressing the [-/NO] button.
Press the [+/YES] button. A conrmation message will appear on the display.
Press the [+/YES] button to delete the Song. Writing! message will appear while the track is being deleted.

Writing!

This function erases all backup data in the instruments ash memory and restores the initial default settings. The following initialization procedures are provided. Turn the power on by pressing the [STANDBY/ON] switch while holding the highest white key on the keyboard. The backed up data will be erased and the default values restored.
When you execute the Initialization, backup parameters will be cleared.
Initialization does not delete the les transferred from the computer. If you want to delete the les, see Deleting Files below.
Parameters that are saved in backup: User Songs Style number 107 Touch Response on/off setting Passing status of Song and Step The following Function settings: Tuning, Split Point, Touch Sensitivity, Style Volume, Song Volume, Metronome Volume, Demo Cancel, Panel Sustain Although the above parameters are always backed up, and are maintained even when the power is turned off, they will be completely erased by the initialization. You can save the settings as backup data to your computer, by using the Musicsoft Downloader (MSD) software. Refer to the section Transferring a backup le from the PSR-E323/YPT-320 to a computer on page 62.

Deleting Files

To clear Song data and Style data that has been transferred to the internal ash memory from a computer, simultaneously hold down the highest white key and the three highest black keys on the keyboard and turn the power on by pressing the [STANDBY/ON] switch.

Press the [FUNCTION] button as many time as necessary to select the style le load function StyleReg.

StyleReg

After about 2 seconds the name of a registerable style le will appear in the display. If multiple loadable style les have been transferred to the instrument, you can use the [+] and [-] buttons to select the other les in sequence.
Execute the register operation. With the name of the style le you want to register shown in the display, press the number [0] button.
A conrmation message for the register operation will appear. Press the [+/YES] button to actually register the le.
The [FUNCTION] button gives you access to a variety of operations related to adjusting or enhancing the sound and making settings for connection to external devices.
Select the item and change the value
There are 34 different items that can be set.
Set the value by using the number buttons [0][9], [+], [-].
Press the [FUNCTION] button a number of times until desired item appears. Each time the [FUNCTION] button is pressed 34 function items are displayed in sequence. The description and display sample is provided on the Function Setting List on page 5657.
For on/off settings or the PC Mode setting, use [+]/[-] buttons.
Press the [+] and [-] buttons simultaneously to instantly reset the numeric parameter to its default setting.

Function item

Function Setting List
Item Style Volume Song Volume Transpose Tuning Split Point Display StyleVol SongVol TransPos Tuning SplitPnt Range/settings -120012 -(C-2G8) Description Determines the volume of the Style. Determines the volume of the Song. Determines the pitch of the instrument by semitone increments. Sets the pitch of the instruments sound in 1-cent increments. Determines the highest key for the Split Voice and sets the Split pointin other words, the key that separates the Split (lower) and Main (upper) Voices. The Split Point setting and Accompaniment Split Point setting are automatically set to the same value. When Touch Response is on, this determines the sensitivity of the feature. Select and register a style le from ash les that are loaded from computer. Determines the volume of the Main Voice. Determines the octave range for the Main Voice. Determines how much of the Main Voices signal is sent to the Chorus effect.

Erasing Transferred Song Data from the PSR-E323/YPT-320 Memory
To erase all Songs transferred from the computer, use ash clear function on page 41. To erase specic Songs transferred from the computer, use the Delete function on Musicsoft Downloader.
Using Transferred Songs for Lessons
In order to use Songs (only SMF format 0) transferred from a computer for lessons it is necessary to specify which channels are to be played back as the right-hand and left-hand parts. Refer to the Lesson Track (R) or Lesson Track (L) in the Function Setting List on page 57. The procedure for setting the guide track is as follows: Select a transferred Song you want to use for lessons. Press the [FUNCTION] button a number of times until the R-Part or L-Part appears in the display, and then use the number buttons [0] [9], [+], [-] to select the channel you want to play back as the specied right- or left-hand part. We recommend that you select channel 1 for the right-hand part and channel 2 for the left-hand part.
Preset Song data cannot be transmitted from the PSR-E323/ YPT-320.
The backup data, including the ve User Songs is transmitted/received as a single le. As a result, all backup data (including the ve Songs) will be overwritten every time you transmit or receive. Keep this in mind when transferring data. Do not rename the backup le on the computer. If you do so, it will not be recognized when transferred to the instrument.

Troubleshooting

Problem When the instrument is turned on or off, a popping sound is temporarily produced. When using a mobile phone, noise is produced. There is no sound even when the keyboard is played or when a Song or Style is being played back. Not all of the voices seem to sound, or the sound seems to be cut off. Playing keys in the right hand area of the keyboard does not produce any sound. The volume is too soft. The sound quality is poor. The rhythm stops unexpectedly or will not play. The recorded data of the Song, etc. does not play correctly. The LCD display suddenly goes dark, and all panel settings are reset. The Style or Song does not play back when the [START/STOP] button is pressed.
Possible Cause and Solution This is normal and indicates that the instrument is receiving electrical power. Using a mobile phone in close proximity to the instrument may produce interference. To prevent this, turn off the mobile phone or use it further away from the instrument. Check that nothing is connected to the PHONES/OUTPUT jack on the rear panel. When a set of headphones is plugged into this jack, no sound is output. Check the Local Control on/off. (See page 59.) The instrument is polyphonic up to a maximum of 32 notes including Dual voice, Split Voice, auto accompaniment, song, and Metronome. Notes exceeding this limit will not sound. When using the Dictionary function (page 54), the keys in the right hand area are used only for entering the chord root and type.

LSB (0127) 35

246 *285 286
MIDI Program Voice Name Change# (1128) 32 Guitar Harmonics 2 BASS 33 Acoustic Bass 33 Jazz Rhythm 33 Velocity Crossfade Upright Bass 34 Finger Bass 34 Finger Dark 34 Bass & Distorted Electric Guitar 34 Finger Slap Bass 34 Finger Bass Modulated Bass 35 Pick Bass 35 Muted Pick Bass 36 Fretless Bass 36 Fretless Bass Fretless Bass Fretless Bass Slap Bass Punch Thumb Bass 38 Slap Bass Velocity Switch Slap 39 Synth Bass Techno Synth Bass 40 Synth Bass Mellow Synth Bass 40 Sequenced Bass 40 Click Synth Bass 40 Synth Bass 2 Dark 40 Modular Synth Bass 40 DX Bass STRINGS 41 Violin 41 Slow Violin 42 Viola 43 Cello 44 Contrabass 45 Tremolo Strings 45 Slow Tremolo Strings 45 Suspense Strings 46 Pizzicato Strings 47 Orchestral Harp 47 Yang Chin 48 Timpani ENSEMBLE 49 Strings Stereo Strings 49 Slow Strings 49 60s Strings 49 Orchestra 49 Orchestra Tremolo Orchestra 49 Velocity Strings 50 Strings Stereo Slow Strings 50 Legato Strings 50 Warm Strings 50 Kingdom 51 Synth Strings Synth Strings Choir Aahs 53 Stereo Choir 53 Mellow Choir 53 Choir Strings 54 Voice Oohs 55 Synth Voice 55 Synth Voice Choral 55 Analog Voice 56 Orchestra Hit 56 Orchestra Hit 2

LSB (0127) 64

MIDI Program Voice Name Change# (1128) 56 Impact BRASS 57 Trumpet 57 Warm Trumpet 58 Trombone 58 Trombone Tuba 60 Muted Trumpet 61 French Horn 61 French Horn Solo 61 French Horn Horn Orchestra 62 Brass Section 62 Trumpet & Trombone Section 63 Synth Brass Resonant Synth Brass 64 Synth Brass Soft Brass 64 Choir Brass REED 65 Soprano Sax 66 Alto Sax 66 Sax Section 67 Tenor Sax 67 Breathy Tenor Sax 68 Baritone Sax 69 Oboe 70 English Horn 71 Bassoon 72 Clarinet PIPE 73 Piccolo 74 Flute 75 Recorder 76 Pan Flute 77 Blown Bottle 78 Shakuhachi 79 Whistle 80 Ocarina SYNTH LEAD 81 Square Lead 81 Square Lead LM Square 81 Hollow 81 Shroud 81 Mellow 81 Solo Sine 81 Sine Lead 82 Sawtooth Lead 82 Sawtooth Lead Thick Sawtooth 82 Dynamic Sawtooth 82 Digital Sawtooth 82 Big Lead 82 Sequenced Analog 83 Calliope Lead 83 Pure Lead 84 Chiff Lead 85 Charang Lead 85 Distorted Lead 86 Voice Lead 87 Fifths Lead 87 Big Five 88 Bass & Lead 88 Big & Low 88 Fat & Perky 88 Soft Whirl SYNTH PAD 89 New Age Pad 89 Fantasy

Some songs have been edited for length or for ease in learning, and may not be exactly the same as the original. A Song Book is available that includes scores for all internal songs (excepting Songs 13). To obtain the Song Book, complete the user registration at the following website. http://music.yamaha.com/registration/

Effect Type List

Harmony Types
No. Harmony Type Duet Trio Block Country Octave Trill 1/4 note Trill 1/6 note Trill 1/8 note Trill 1/12 note Trill 1/16 note Trill 1/24 note Trill 1/32 note Tremolo 1/4 note Tremolo 1/6 note Tremolo 1/8 note Tremolo 1/12 note Tremolo 1/16 note Tremolo 1/24 note Tremolo 1/32 note Echo 1/4 note Echo 1/6 note Echo 1/8 note Echo 1/12 note Echo 1/16 note Echo 1/24 note Echo 1/32 note
Description If you want to sound one of the harmony types 0105, play keys to the right side of the Split Point while playing chords in the left side of the keyboard after turning Auto Accompaniment on. One, two or three notes of harmony are automatically added to the note you play. When playing back a Song that includes chord data, harmony is applied whichever keys are played.
If you keep holding down two different notes, the notes alternate (in a trill) continuously.
If you keep holding down a single note, the note is repeated continuously. (The repeat speed differs depending on the selected type.)
If you keep holding down a note, echo is applied to the note played. (The echo speed differs depending on the selected type.)

Reverb Types

No. 10 Hall 13 Room 12 Stage 12 Plate 12 Off Reverb Type Concert hall reverb. Small room reverb. Reverb for solo instruments. Simulated steel plate reverb. No effect. Description

Chorus Types

No. 5 Chorus 12 Flanger 12 Off Chorus Type Description Conventional chorus program with rich, warm chorusing. This produces a rich, animated wavering effect in the sound. No effect.

Specications

Keyboards 61 standard-size keys (C1C6), with Touch Response Display LCD display (backlit) Setup STANDBY/ON MASTER VOLUME: MINMAX Panel Controls [L]/[REC TRACK 2], [R]/[REC TRACK 1], [1 LISTENING 2 TIMING 3 WAITING], [KEYS TO SUCCESS], [PHRASE REPEAT], [A-B REPEAT]/[ACMP ON/OFF], [REW]/ [INTRO/ENDING/rit.], [FF]/[[MAIN/AUTO FILL], [TEMPO/TAP], [REC], [PAUSE]/[SYNC START], [START/STOP], [SONG], [STYLE], [VOICE], [FUNCTION], [PORTABLE GRAND], [MUSIC DATABASE], [REVERB], [DEMO], [METRONOME], [SPLIT], [DUAL], [HARMONY], [TOUCH], number buttons [0][9], [+/ YES], [-/ NO] Voice 108 panel voices + 12 drum kits + 1 sound effect kit + 359 XGlite voices + 2 XGlite optional voices Polyphony: 32 DUAL SPLIT Style 106 preset Styles + ash memory Style Control: ACMP ON/OFF, SYNC START, START/STOP, INTRO/ENDING/rit., MAIN/AUTO FILL Fingering: Multi ngering Style Volume Style Register Education Feature Chord Dictionary KEYS TO SUCCESS 1 LISTENING, 2 TIMING, 3 WAITING Phrase Repeat Function Style Volume, Song Volume, Transpose, Tuning, Split Point, Touch Sensitivity, Style Register, Main voice (Volume, Octave, Chorus Send Level), Dual voice (Voice, Volume, Octave, Chorus Send Level), Split voice (Voice, Volume, Octave, Chorus Send Level), Reverb Type, Reverb level, Chorus Type, Panel Sustain, Harmony Type, Harmony Volume, PC mode (PC1/PC2/Off), Local On/Off, External Clock, Initial Setup Send, Time Signature (Numerator, Denominator), Metronome Volume, Lesson Track (R), Lesson Track (L), Demo Cancel Effects Reverb: 9 types Chorus: 4 types Harmony: 26 types Song 102 Preset Songs + 5 User Songs + Flash Memory Song Clear Song Volume Music Database 100 Recording Song User Song: 5 Songs Recording Tracks: 1, 2 MIDI Local On/Off Initial Setup Send External Clock PC mode Auxiliary jacks PHONES/OUTPUT, DC IN 12V, MIDI IN/OUT, SUSTAIN Amplier 2.5W + 2.5W Speakers 12cm x 2 Power Consumption 10W (When using PA-130 power adaptor) Power Supply Adaptor: Yamaha PA-130 or an equivalent Batteries: Six AA size, LR6 or equivalent batteries Dimensions (W x D x H) 945 x 369 x 132 mm (37-3/16" x 14-1/2" x 5-3/16") Weight 4.9kg (10 Ibs. 13 oz.) (not including batteries) Supplied Accessories Music Rest Owners Manual My Yamaha Product User Registration

Optional Accessories AC Power Adaptor: Yamaha PA-130 or an equivalent USB-MIDI Interface: UX16 Footswitch: FC4/FC5 Keyboard Stand: L-2C/L-2L Headphones: HPE-150/HPE-30
* Specications and descriptions in this owners manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specications at any time without prior notice. Since specications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
09, +, -... 26 1LISTENING 2TIMING 3WAITING.. 31
Harmony... 42 Harmony Type List.. 73 Harmony Volume.. 57
AB Repeat... 51 AC Power Adaptor.. 8 ACMP ON/OFF.. 20 Auto Accompaniment.. 18, 20 Auto accompaniment range.. 18, 20
Initial Send... 57 Initialization... 41 Intro... 23
Backup... 41, 62 Backup File... 62 Battery... 8 Beat Display... 27
Keyboard Display.. 27 KEYS TO SUCCESS.. 28
Left.... 32 Lesson.. 28, 3234 Lesson track R/L for transferred songs. 57, 62 Listening... 33 Local... 57, 59
Cancel.. 40 Chord... 2425 Chord Dictionary.. 54 Chord Display.. 27 Chorus.. 43 Chorus Send Level (Main, Dual and Split). 43, 5657 Chorus Type List... 73 Computer... 58
Main/Auto fill... 23 Master Volume Control.. 9 Measure... 27 Melody Voice... 52 Metronome... 14, 48 Metronome Volume... 48 MIDI... 58 MIDI IN/OUT.. 58 Music Database... 36 Music Rest... 9 Mute... 51
DC IN 12V.. 8 Delete (File)... 41 Delete (User Song)... 40 Demo... 17 Display... 27 Drum Kit... 15 Drum Kit List... 68 Dual... 45
NO... 40 Notation... 27 Number buttons... 26
Ending.. 23 External Clock... 57, 59
FF... 17 Flash Memory.. 61 Footswitch (Sustain jack).. 9 Function... 56 Function Setting List.. 5657
Octave (Dual)... 57 Octave (Main).. 56 Octave (Split)... 57 One Touch Setting.. 50 Option... 74

Grade... 34

Part.... 32 Passing Status.. 27, 30 Pause... 17 PC setting.. 59 PHONES/OUTPUT... 9 Phrase... 35 Phrase Repeat.. 28, 35 Press and Hold for a while... 26
Tempo.. 22 TEMPO/TAP.. 22 Time Signature... 48 Timing.. 33 Touch Response.. 44 Touch sensitivity... 44 Track.. 27, 38, 51 Track Rec... 3839 Transfer... 60 Transpose.. 49 Tuning.. 50
Recording... 3739 Remote Control... 60 Reverb.. 43 Reverb Level.. 57 Reverb Type List... 73 Rew... 17 Rhythm... 18 Right... 32 rit.(ritardando).. 23 Root... 25, 54

Do not insert a finger or hand in any gaps on the instrument. Never insert or drop paper, metallic, or other objects into the gaps on the panel or keyboard. Do not rest your weight on, or place heavy objects on the instrument, and do not use excessive force on the buttons, switches or connectors. Do not use the instrument/device or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed. Always turn the power off when the instrument is not in use. Even when the [ ](Standby/On) switch is in the Standby position, electricity is still flowing to the instrument at the minimum level. When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet. Make sure to discard used batteries according to local regulations.

NOTICE

To avoid the possibility of damage to the product, data or other property, follow the notices below. Handling and Maintenance Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio may generate noise. Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components. Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard. When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths. Saving data Some data items (page 50) are automatically saved as backup data in the internal memory even if you turn the power off. Saved data may be lost due to malfunction or incorrect operation. Save important data to external device such as a computer (page 77).
About copyrights Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal use. This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license to use others copyrights. Such copyrighted materials include, without limitation, all computer software, style files, MIDI files, WAVE data, musical scores and sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws. Any violation of copyright has legal consequences. DONT MAKE, DISTRIBUTE OR USE ILLEGAL COPIES. About functions/data bundled with the instrument Some of the preset songs have been edited for length or arrangement, and may not be exactly the same as the original. About this manual The illustrations and LCD screens as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your instrument. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

Included Accessories

The package includes the following items. Please check that you have them all. Owners Manual Music rest Accessory CD-ROM Data List My Yamaha Product User Registration
* The PRODUCT ID on the sheet will be needed when you fill out the User Registration form.

Music Rest

Insert the music rest into the slots as shown.

Special Features

Creating New Sounds

Page 22

By adjusting just two knobs you can add varying degrees of distortion, sweetness, or other characteristics to a sound to change it subtly or drastically. Parameters that can be assigned to the knobs include effect, filter, envelope generator and more. You can create new sounds in real time!

Arpeggio Function

Page 20
Similar to the arpeggio functions provided on some synthesizers, this function automatically produces arpeggios (broken chords) when you simply play the appropriate notes on the keyboard. A variety of arpeggios can be produced by changing your fingering or the arpeggio type.
Performance assistant technology

Page 37

Play along with a song on the instruments keyboard and produce a perfect performance every time. even if you play wrong notes! All you have to do is play on the keyboardalternately on the left- and right-hand ranges of the keyboard, for exampleand youll sound like a pro as long as you play in time with the music.
Play a Variety of Instrument Voices

Page 16

The instrument voice that sounds when you play the keyboard can be changed to violin, flute, harp, or any of an extensive range of voices. You can change the mood of a song written for piano, for example, by using violin to play it instead. Experience a whole new world of musical variety.

Play Along with Styles

Page 27
Want to play with full accompaniment? Try the auto-accompaniment Styles. The accompaniment styles provide the equivalent of a full backing band covering a wide variety of styles from waltzes to 8-beat to euro-trance. and much more. Select a style that matches the music you want to play, or experiment with new styles to expand your musical horizons.

EuTrance

Contents
About this Owners Manual and Data List.7 Included Accessories..7 Special Features..8
Handy Performance Features

You can also specify the repeat playback of all preset songs or songs transferred from a computer. The specified songs can also be played in random order (page 66).
Song Fast Forward, Fast Reverse, and Pause
These are just like the transport controls on a cassette deck or CD player, letting you fast forward [ ] (FF), rewind [ ] (REW) and pause [ ] (PAUSE) playback of the song.
When an A-B repeat range is specified the fast reverse and forward function will only work within that range.
REW Press the fast reverse button to rapidly return to an earlier point in the song.
FF Press the fast forward button to rapidly skip ahead to a later point in the song.
PAUSE Press the pause button to pause playback.
Select a Song For a Lesson
Yamaha Education Suite You can select song you like and use it for a left-hand, right-hand, or both-hands lesson. During the lesson you can play as slowly as you like, and you can even play wrong notes. Song playback will slow down to a speed you can handle. Its never too late to start learning!

The practice methods:

Lesson 1Waiting Lesson 2Your Tempo Lesson 3Minus One Learn to play the correct notes. Learn to play the correct notes with the correct timing. Learn to play the correct notes at the correct timing along with the song.

Lesson 1Waiting

In this lesson, try playing the correct notes. Play the note shown in the display. The song will wait until you play the right note.
Select a song for your lesson. Select a song from the Piano Solo, Piano Ensemble category! For this example try selecting the 012 ForElise. Turn off playback of the part you wish to practice. The preset songs have separate left- and right-hand parts. The right-hand part is selected by the [RIGHT](1) button and the left-hand part is selected by the [LEFT](2) button. You can turn the left- and right-hand parts on or off as required in order to practice the corresponding part (the part that is turned off) on the keyboard. You can practice both parts when both the left- and right-parts are turned off.
Song numbers 10 and 11 are function demos for performance assistant. The lesson function cannot be used with them. You can also use songs (only SMF format 0) transferred from the computer and saved to flash memory. (pages 7577)
You can turn parts on or off, even during playback.

The score for Hallelujah Chorus is provided in the separate Data List.
Try switching styles while the song plays back.
Press the [EASY SONG ARRANGER] button. The indicator lights when the Easy Song Arranger function is on.
Select a Song. Press the [SONG] button, then select the song you want to arrange. Select the songs that include the required chord data referring to the Song List in the separate Data List.
Using the Easy Song Arranger
Listen to the song. Press the [ ] (START/STOP) button to begin playback of the song. Move on to the next step while the song is playing.
When playing song numbers 010, 011 and 021 to 030 while using the Easy Song Arranger, melody tracks will be automatically muted and no melody will sound. In order to hear the melody tracks you will need to press the track buttons [3] to [5].
Select a style. Press the [STYLE] button and then rotate the dial to hear how the song sounds with different styles. As you select different styles the song will remain the same while only the styles change.
You can also press the [MAIN/AUTO FILL] button to change the styles main section. Changing the Melody Voice You can change the songs melody voice while the Easy Song Arranger is on. Press the [VOICE] button once to display the name of the current melody voice. Use the dial to select a different voice, then press and hold the [VOICE] button for longer than a second. SONG MELODY VOICE will appear in the display for a few seconds, indicating that the newly selected voice has replaced the songs original melody voice.
Because the Easy Song Arranger uses song data you cant specify chords by playing in the accompaniment range of the keyboard. The [ACMP ON/ OFF] button will not function. If the time signature of the song and style are different, the time signature of the song will be used.
Press the [EASY SONG ARRANGER] button to turn the function off. If the song or style is being played back, first stop the playback, then turn the Easy Song Arranger function off. The indicator will go out.
Record Your Own Performance
You can record up to 5 of your own performances and save them as user songs 031 through 035. The recorded song can be played back on the instrument.

Recording

Press the [REC] button.
Track 1 is automatically selected
If all User Songs (Song numbers 031035) contain recorded data, Song 031 will automatically be selected. In this case, you will record over and erase any previous data in Song 031, so be careful that you wont be erasing any material you want to keep!

User 1

Flashes The lowest-numbered unrecorded User Song (Song numbers 031035) available for recording is displayed. If you want to select the Song you will be recording, select the desired Song number by using the dial.

Flashes

Accompaniment cannot be turned on or off once the [REC] button is pressed.
You can turn off the Record mode by pressing the [REC] button again (Track 1 stop flashing).
Start recording. When you play the keyboard, recording will begin.
Stop recording. Pressing the [START/STOP] button stops recording and writes the data to the User Song. (A Writing! message is shown.)
To playback the newly recorded performance, press the [START/STOP] button.
Never attempt to turn the power off when a Writing! message is shown in the display. Doing so can damage the flash memory and result in a loss of data.
After youve selected the desired User Song for recording, you can select a Style to be recorded as well. To do this, press the [STYLE] button and select the Style number while the ACMP indication is on.
Recording to a specified track
Recordable Data You can record up to a total of 6 tracks: 5 melody tracks and 1 style (chord) track. Each track can be recorded individually. Melody Track [1][5].. Record the melody parts. Style Track [A].. Records the chord part.
Melody Chords Specify track(s) and record
Up to approximately 10,000 notes can be recorded for the five user songs if you record only to the melody tracks. Up to approximately 5,500 chord changes can be recorded for the five user songs if you record only to the style track.

Track 1

Track 2

Track 3

Track 4

Track 5

Style Track
Track Mute This instrument allows you to choose whether recorded tracks will play back while you are recording or playing back other tracks (page 68).
Press the [SONG] button, then use the dial to select the user song number (031035) you want to record to.
Rotate the dial to select a song number between 031 and 035.
Select the track(s) you want to record to and confirm your selection on the display. NOTICE Record a Melody Track and the Accompaniment Track Together If you record to a track that Press the melody track button [1][5] you want to record to while holding the contains previously[REC] button. recorded data the previous data will be overwritten Next, press the [A] button while holding the [REC] button. and lost. The selected tracks will flash in the display.
Press and hold Track 1 and Style Track will flash
Style accompaniment is automatically turned on when you select the style track [A] for recording. Style accompaniment cannot turned on or off while recording is in progress.
Record a Melody track Press the melody track button [1][5] you want to record to while holding the [REC] button. The selected track will flash in the display.

If style accompaniment is on and track [A] has not yet been recorded, the style track [A] will automatically be selected for recording when a melody track is selected. If you only want to record a melody track, be sure to turn the style track [A] off.

Track 1 will flash

To cancel recording to a selected track, press that track button a second time.
Recording will start when you play on the keyboard. You can also start recording by pressing the [ ] (START/STOP) button. The current measure will be shown on the display during recording.

Recording starts

Current measure
If the memory becomes full during recording a warning message will appear and recording will stop automatically. Use the song clear or track clear (page 47) function to delete unwanted data and make more room available for recording, then do the recording again.
Stop recording by pressing the [ button.

] (START/STOP) or [REC]

When recording stops the current measure number will return to 001 and the recorded track numbers in the display will light.
If you want to record only the rhythm (percussion) part, press the [ ](START/ STOP) button to play just the rhythm, then add the section change by pressing the [INTO/ENDING/rit.] button or [MAIN/AUTO FILL] button.
To Record Other Tracks Repeat steps 2 through 4 to record any of the remaining tracks. By selecting an unrecorded tracktrack buttons [1][5], [A]you can record the new track while listening to previously recorded tracks (the playback tracks will appear in the display). You can also mute previously recorded tracks (the muted tracks will not appear in the display) while recording new tracks. To Re-record a Track Simple select the track you want to re-record for recording in the normal way. The new material will overwrite the previous data.
When the recording is done. To playback the newly recorded performance, press the [ button.

] (START/STOP)

To Play Back a User Song User songs are played back in the same way as regular songs (page 30).
1 Press the [SONG] button. 2 The current song number/name will be displayeduse the dial to select the user song (031035) you want to play. 3 Press the [ ] (START/STOP) button to start playback.

ENDING

This switches to the ending section. When the ending is finished, the auto accompaniment stops automatically. You can have the ending gradually slow down (ritardando) by pressing the [INTRO/ENDING/rit.] button again while the ending is playing back. Synchro Stop
When this function is selected the accompaniment style will only play while you are playing chords in the accompaniment range of the keyboard. Style playback will stop when you release the keys. To turn the function on, press the [SYNC STOP] button.

INTROA

Youre now ready to play the intro.
Appears when the synchro-stop function is engaged.

Accompaniment range

The style will play while you are playing the keys
Style playback will stop when you release the keys

FILL AB

When the fill-in is finished, it leads smoothly into the selected main section A/B.
As soon as you play a chord with your left hand, the Intro of the selected Style starts. For this example, play a C major chord (as shown below). For information on how to enter chords, see Chords on page 29.
Changing the tempo of the Style
Styles can be played at any tempo you desirefast or slow.
Adjusting the Style Volume
Press the [STYLE] button to engage the style function.
Press the [TEMPO/TAP] button to call up the Tempo setting in the display after selecting a Style.
Use the CATEGORY [ ] and [ ] buttons to select the Style Volume item.
Use the dial to select a tempo from 011 to 280 quarter-note beats per minute. Press the [+] and [-] buttons simultaneously to instantly reset the value to the default tempo of a Style.
You can change the tempo during style playback by pressing the [TEMPO/TAP] button just twice.

StyleVol

Use the dial to set the style volume between 000 and 127.

Setting the Split Point

The initial default split point is key number 54 (the F#2 key), but you can change it to another key using the procedure described below.

Tap Start

You can start the style by simply tapping the [TEMPO/TAP] button at the required tempo4 times for time signatures in 4, and three times for time signatures in 3. You can change the tempo during style playback by pressing the button just twice.
Press the [STYLE] button. Press and hold the [ACMP ON/OFF] for longer than a second so that the Split point item appears.

SplitPnt

Play a Style with Chords but No Rhythm (Stop Accompaniment)
When auto accompaniment is on (the ACMP ON icon is showing) and Synchro Start is off, you can play chords in the left-hand accompaniment range of the keyboard while the style is stopped and still hear the accompaniment chords. This is Stop Accompaniment, and any of the chord fingerings recognized by the instrument can be used (page 29).

Touch Sensitivity Volume Octave Pan Reverb Level Chorus Level Attack Time Release Time Filter Cutoff Filter Resonance Voice Volume Octave Pan Dual Voice Reverb Level Chorus Level Attack Time Release Time Filter Cutoff Filter Resonance Voice Volume Octave Split Voice Pan Reverb Level Chorus Level Reverb Type Chorus Type Effect Master EQ Type
TouchSns M.Volume M.Octave M.Pan M.Reverb M.Chorus M.Attack M.Releas M.Cutoff M.Reso. D.Voice D.Volume D.Octave D.Pan D.Reverb D.Chorus D.Attack D.Releas D.Cutoff D.Reso. S.Voice S.Volume S.Octave S.Pan S.Reverb S.Chorus Reverb Chorus

Category Harmony

Settings Harmony Type Harmony Volume Arpeggio Type Arpeggio Velocity
Display HarmType HarmVol ARP Type ARP Velo Quantize Pdl Func Sff Load PC mode Local ExtClock KbdOut StyleOut SongOut InitSend TimesigN
Range/Settings (Original), 2 (Thru) OFF, 1/8, 1/16 1(Sustain)/ 2(Arp Hold)/ 3(Hold+Sus) 001nnn PC1/PC2/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF YES/NO 0060 Half note, Quarter note, Eighth note, Sixteenth note 000127 GuideTrack 116, OFF GuideTrack 116, OFF ON/OFF 1(Demo)/ 2(Preset)/ 3(User)/ 4(Download) 1(Normal)/ 2(Random) ON/OFF
Description Determines the Harmony type. Determines the volume of the Harmony effect. Determines the Arpeggio type. Sets the velocity mode for arpeggio playback. Synchronizes arpeggio playback to a Style or Song. Determines the pedal function in the arpeggio mode. Loads a Style file. Optimizes the MIDI settings when you connect to a computer. Determines whether the instruments keyboard controls the internal tone generator (ON) or not (OFF). Determines whether the instrument synchronizes to the internal clock (OFF) or an external clock (ON). Determines whether keyboard performance data of the instrument is transmitted (ON) or not (OFF). Determines whether Style data is transmitted (ON) via USB or not (OFF) during Style playback. Determines whether User Song is transmitted (ON) via USB or not (OFF) during Song playback. Lets you send the data of the panel settings to a computer. Press [+] to send, or press [-] to cancel. Determines the time signature of the Metronome.

Arpeggio

Arpeggio Quantize Arpeggio Pedal

Style File Load PC

Style File Load PC mode Local On/Off External Clock Keyboard Out
MIDI Style Out Song Out Initial Send Time Signature Numerator Metronome Time Signature Denominator Metronome Volume Lesson Track (R)

TimesigD MtrVol R-Part

Sets the length of each metronome beat. Determines the volume of the Metronome. Determines the guide track number for your right hand lesson. The setting is only effective for songs in SMF format 0 transferred from a computer. Determines the guide track number for your left hand lesson. The setting is only effective for songs in SMF format 0 transferred from a computer. Determines whether the Grade function is on or off. Determines the repeat playback group.

10 MB or more

512 MB or more

Windows 7

1 GB or more (32bit)/2 GB or more (64-bit)

Software Installation

If you have any problems with the installation, refer to the troubleshooting section on page 82.
Start the computer and use the Administrator account to log on to Windows. Close all applications and windows that are open. Insert the Accessory CD-ROM into your computers CD-ROM drive. Turn off the power of the instrument. Connect the USB connector of the computer to the USB connector of the MIDI instrument with a standard USB cable.
The example displays shown in this guide are in English.
Installing / Updating the USB-MIDI Driver
In order to be able to communicate with and use MIDI instruments connected to your computer, the appropriate driver software must be properly installed on your computer. The USB-MIDI driver allows sequence software and similar applications on your computer to transmit and receive MIDI data to and from instruments via a USB cable.
Computer Sequence software USB Cable Driver
Do not use a USB hub for connecting multiple USB devices.
If you are using several MIDI instruments with USB connection at the same time, connect all the instruments to the computer and turn on the power for all of them, then perform the following installation procedure.

MIDI instrument

Turn on the power of the instrument(s). When the Found New Hardware Wizard window appears, click [Cancel].
Follow the steps below to install (or update) the USBMIDI driver.
On some computers, it may take a few minutes before this screen appears.
Disconnect all USB devices from the computer except for the mouse and computer keyboard.

Windows XP

This screen will not appear on Windows 7 When the. message Device driver software was not successfully installed. appears, continue the installation procedure.
This screen will not appear if you are updating the USBMIDI driver from the previous version. Continue the installation procedure.
Open the following folder from the CDROM drive in your My Computer folder, and double click setup.exe. For users of 32 bit version Windows 2000/XP/ Vista/7: USBdrv32_ For users of 64 bit version Windows XP/Vista/7: USBdrv64_

1 Select [Control Panel]* [System] [Hardware] [Device Manager] (for Windows 2000/XP), or select [Control Panel] [Device Manager] (for Windows Vista/7).
* Classic View only in Windows XP.
2 Make sure that no ! or x marks appear
at Universal serial bus controller or USB Root Hub If you see an ! or x mark, the. USB controller is disabled.
* You can obtain the latest version of the Musicsoft Downloader at the following web site. http://music.yamaha.com/download/
Only Musicsoft Downloader can be used to transfer files between this instrument and a computer. No other file transfer application can be used.
Is any unknown device registered? If driver installation fails, the instrument will be marked as an Unknown device, and you will not be able to install the driver. Delete the Unknown device by following the steps below.
2 Look for Other devices in the menu View

devices by type.

3 If you find Other devices double-click it to ,
extend the tree to look for Unknown device If one appears, select it and click. the [Remove] button.
4 Remove the USB cable from the instrument,
and make the connection again.
5 Install the driver again. (pages 8081)
When controlling the instrument from your computer via USB, the instrument does not operate correctly or no sound is heard. Did you install the driver? (page 80) Is the USB cable connected correctly? Are the volume settings of the instrument, playback device, and application program set to the appropriate levels? Have you selected an appropriate port in the sequence software? Are you using the latest USB MIDI driver? The latest driver can be downloaded from the following web site. http://music.yamaha.com/download/
How can I remove the software? [Windows 2000/XP]
1 Disconnect all USB devices from the computer except for the mouse and keyboard.
2 Start the computer and log on to the

Administrator account.

Exit from any open applications and close all open windows.

5. DISCLAIMER OF WARRANTY ON SOFTWARE You expressly acknowledge and agree that use of the SOFTWARE is at your sole risk. The SOFTWARE and related documentation are provided AS IS and without warranty of any kind. NOTWITHSTANDING ANY OTHER PROVISION OF THIS AGREEMENT, YAMAHA EXPRESSLY DISCLAIMS ALL WARRANTIES AS TO THE SOFTWARE, EXPRESS, AND IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS. SPECIFICALLY, BUT WITHOUT LIMITING THE FOREGOING, YAMAHA DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS, THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE, OR THAT DEFECTS IN THE SOFTWARE WILL BE CORRECTED. 6. LIMITATION OF LIABILITY YAMAHAS ENTIRE OBLIGATION HEREUNDER SHALL BE TO PERMIT USE OF THE SOFTWARE UNDER THE TERMS HEREOF. IN NO EVENT SHALL YAMAHA BE LIABLE TO YOU OR ANY OTHER PERSON FOR ANY DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, EXPENSES, LOST PROFITS, LOST DATA OR OTHER DAMAGES ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THE SOFTWARE, EVEN IF YAMAHA OR AN AUTHORIZED DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. In no event shall Yamahas total liability to you for all damages, losses and causes of action (whether in contract, tort or otherwise) exceed the amount paid for the SOFTWARE. 7. THIRD PARTY SOFTWARE Third party software and data (THIRD PARTY SOFTWARE) may be attached to the SOFTWARE. If, in the written materials or the electronic data accompanying the Software, Yamaha identifies any software and data as THIRD PARTY SOFTWARE, you acknowledge and agree that you must abide by the provisions of any Agreement provided with the THIRD PARTY SOFTWARE and that the party providing the THIRD PARTY SOFTWARE is responsible for any warranty or liability related to or arising from the THIRD PARTY SOFTWARE. Yamaha is not responsible in any way for the THIRD PARTY SOFTWARE or your use thereof. Yamaha provides no express warranties as to the THIRD PARTY SOFTWARE. IN ADDITION, YAMAHA EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, as to the THIRD PARTY SOFTWARE. Yamaha shall not provide you with any service or maintenance as to the THIRD PARTY SOFTWARE. Yamaha is not liable to you or any other person for any damages, including, without limitation, any direct, indirect, incidental or consequential damages, expenses, lost profits, lost data or other damages arising out of the use, misuse or inability to use the THIRD PARTY SOFTWARE. 8. GENERAL This Agreement shall be interpreted according to and governed by Japanese law without reference to principles of conflict of laws. Any dispute or procedure shall be heard before the Tokyo District Court in Japan. If for any reason a court of competent jurisdiction finds any portion of this Agreement to be unenforceable, the remainder of this Agreement shall continue in full force and effect. 9. COMPLETE AGREEMENT This Agreement constitutes the entire agreement between the parties with respect to use of the SOFTWARE and any accompanying written materials and supersedes all prior or contemporaneous understandings or agreements, written or oral, regarding the subject matter of this Agreement. No amendment or revision of this Agreement will be binding unless in writing and signed by a fully authorized representative of Yamaha.

Coverage:

In Order to Obtain Warranty Service: Warranty service will only be provided for defective products within the Warranted Area. Contact your local authorized Yamaha dealer who will advise you of the procedures to be followed. If this is not successful, contact Yamaha at the address, telephone number or website shown below. Yamaha may request that you send the defective product to a local authorized Yamaha Servicer or authorize return of the defective product to Yamaha for repair. If you are uncertain as to whether a dealer has been authorized by Yamaha, please contact Yamahas Service Department at the number shown below, or check Yamahas website at www.Yamaha.com. Product(s) shipped for service should be packed securely and must be accompanied by a detailed explanation of the problem(s) requiring service, together with the original or a machine reproduction of the bill of sale or other dated, proof-of-purchase document describing the product, as evidence of warranty coverage. Should any product submitted for warranty service be found ineligible therefore, an estimate of repair cost will be furnished and the repair will be accomplished only if requested by you and upon receipt of payment or acceptable arrangement for payment. Limitation of Implied Warranties and Exclusion of Damages:
ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO THE APPLICABLE PERIOD OF TIME SET FORTH ABOVE. YAMAHA SHALL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OR FOR DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE, DAMAGE TO ANY OTHER EQUIPMENT OR OTHER ITEMS AT THE SITE OF USE OR INTERRUPTION OF PERFORMANCES OR ANY CONSEQUENCES. YAMAHAS LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, AT YAMAHAS OPTION. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This is the only express warranty applicable to the product specified herein; Yamaha neither assumes nor authorizes anyone to assume for it any other express warranty. If you have any questions about service received or if you need assistance in locating an authorized Yamaha Servicer, please contact:

CUSTOMER SERVICE Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, California 90620-1373 Telephone: 800-854-1569 www.yamaha.com Do not return any product to the above address without a written Return Authorization issued by Yamaha.
2009 Yamaha Corporation of America. Effective: 11/01/09
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below.

NORTH AMERICA

CANADA
Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A. Tel: 714-522-9011
THE NETHERLANDS/ BELGIUM/LUXEMBOURG
THE PEOPLES REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: 021-6247-2211 Tom Lee Music Co., Ltd. 11/F., Silvercord Tower 1, 30 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: 2737-7688 Yamaha Music India Pvt. Ltd. 5F Ambience Corporate Tower Ambience Mall Complex Ambience Island, NH-8, Gurgaon-122001, Haryana, India Tel: 0124-466-5551 PT. Yamaha Music Indonesia (Distributor) PT. Nusantik Gedung Yamaha Music Center, Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: 21-520-2577 Yamaha Music Korea Ltd. 8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong, Kangnam-Gu, Seoul, Korea Tel: 080-004-0022 Yamaha Music Malaysia, Sdn., Bhd. Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-78030900 Yupangco Music Corporation 339 Gil J. Puyat Avenue, P.O. Box 885 MCPO, Makati, Metro Manila, Philippines Tel: 819-7551 Yamaha Music Asia Pte., Ltd. #03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015 Tel: 747-4374 Yamaha KHS Music Co., Ltd. 3F, #6, Sec.2, Nan Jing E. Rd. Taipei. Taiwan 104, R.O.C. Tel: 02-2511-8688 Siam Music Yamaha Co., Ltd. 4, 6, 15 and 16th floor, Siam Motors Building, 891/1 Rama 1 Road, Wangmai, Pathumwan, Bangkok 10330, Thailand Tel: 02-215-2626 Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2317
Yamaha Music Europe Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, The Netherlands Tel: 0347-Yamaha Musique France BP 70-77312 Marne-la-Valle Cedex 2, France Tel: 01-64-61-4000 Yamaha Musica Italia S.P.A. Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 Yamaha Msica Ibrica, S.A. Ctra. de la Coruna km. 17, 200, 28230 Las Rozas (Madrid), Spain Tel: 91-639-8888 Philippos Nakas S.A. The Music House 147 Skiathou Street, 112-55 Athens, Greece Tel: 01-Yamaha Scandinavia AB J. A. Wettergrens Gata 1, Box 30053 S-Gteborg, Sweden Tel: YS Copenhagen Liaison Office Generatorvej 6A, DK-2730 Herlev, Denmark Tel: F-Musiikki Oy Kluuvikatu 6, P.O. Box 260, SF-00101 Helsinki, Finland Tel: Norsk filial av Yamaha Scandinavia AB Grini Nringspark 1, N-1345 sters, Norway Tel: Skifan HF Skeifan 17 P.O. Box 8120, IS-128 Reykjavik, Iceland Tel: Yamaha Music (Russia) Office 4015, entrance 2, 21/5 Kuznetskii Most street, Moscow, 107996, Russia Tel: 0660 Yamaha Music Europe GmbH Siemensstrae 22-34, 25462 Rellingen, Germany Tel: +49-4101-3030