RX-V430RDS

AV Receiver Ampli-tuner audio-vido
YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, VSTRA FRLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
OWNERS MANUAL MODE DEMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING
Printed in Malaysia V890260

0100V430(GB)-cv1

1/18/02, 3:59 PM
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this unit in a well ventilated, cool, dry, clean place with at least 30 cm on the top, 20 cm on the left and right, and 10 cm at the back of this unit away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. To prevent fire or electrical shock, do not place this unit where it may get exposed to rain, water, and/or any type of liquid. Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in a environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. On the top of this unit, do not place: Other components, as they may cause damage and/or discoloration on the surface of this unit. Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury. Containers with liquid in them, as they may cause electrical shock to the user and/or damage to this unit. Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury. Do not plug in this unit to a wall outlet until all connections are complete. Do not operate this unit upside-down. It may overheat, possibly causing damage. Do not use force on switches, knobs and/or cords. When disconnecting the power cord from the wall outlet, grasp the plug; do not pull the cord. Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified. To prevent damage by lightning, disconnect the power cord from the wall outlet during an electrical storm. Take care of this unit so that no foreign objects and/or liquid drops inside this unit. Do not attempt to modify or fix this unit. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reasons. 16 When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet. Be sure to read the TROUBLESHOOTING section on common operating errors before concluding that this unit is faulty. Before moving this unit, press STANDBY/ON to set this unit in the standby mode, and disconnect the AC power plug from the wall outlet. VOLTAGE SELECTOR (China and General models only) The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/220/240 V AC, 50/60 Hz.

This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.

I For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below.
The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.
I Special Instructions for U.K. Model
IMPORTANT THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: Blue: NEUTRAL Brown: LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug.

CAUTION

0101V430_Cau_EN(GB) 2 1/19/02, 8:03 PM

CONTENTS

INTRODUCTION
CONTENTS.. 1 FEATURES... 2 GETTING STARTED.. 3
Checking the package contents.. 3 Installing batteries in the remote control. 3

ADVANCED OPERATION

SET MENU... 42
Adjusting the items on the SET MENU. SPEAKER SET (speaker mode settings). LFE LEVEL... SP DLY TIME (speaker delay time). D. RANGE (dynamic range). L/R BALANCE (balance of the main left and right speakers)... HP TONE CTRL (headphone tone control). I/O ASSIGN (input/output assignment). INPUT MODE (initial input mode).. DISPLAY SET.. 46 10MEM. GUARD (memory guard). 46
CONTROLS AND FUNCTIONS.. 4
Front panel... 4 Remote control... 6 Using the remote control.. 7 Front panel display.. 8

PREPARATION

SPEAKER SETUP.. 9
Speakers... 9 Speaker placement.. 9 Connecting the speakers.. 10

CONNECTIONS.. 13

Before connecting components. 13 Connecting video components.. 14 Connecting audio components.. 16 Connecting the antennas... 17 Connecting an external decoder.. 18 Connecting the power supply cords. 18 Turning on the power... 19
ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS.. 47 ADJUSTING THE DELAY TIME. 48 ADJUSTING THE PARAMETER SETTINGS FOR PRO LOGIC MUSIC.. 49
Changing parameter settings.. 49 PRO LOGIC Music parameter descriptions. 49

BASIC OPERATION

ADDITIONAL INFORMATION
TROUBLESHOOTING.. 50 GLOSSARY... 54 SPECIFICATIONS... 56
SPEAKER MODE SETTINGS. 20 ADJUSTING SPEAKER OUTPUT LEVELS. 21

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.
DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems, Inc.
0102V430_1-8_EN(GB) 2 1/19/02, 8:03 PM

GETTING STARTED

Checking the package contents
Check your package to make sure it contains the following items.

Remote control

Batteries (2) (AA, R06, UM-3)

AM loop antenna

6CH INPUT

D-TV/CBL

TUNER MD/CD-R

PRESET

A/B/C/D/E

PROGRAM

HALL JAZZ CLUB ROCK CONCERT

ENTERTAINMENT

TV SPORTS

MONO MOVIE

75-ohm/300-ohm antenna adapter (U.K. model)
Indoor FM antenna (U.S.A., Canada, China, Korea and General models)

MOVIE 1 THEATER 2

q / DTS SUR.

MATRIX 6.1

SELECT

SET MENU

STEREO

EFFECT

A/V cable (U.S.A., Canada and Australia models)
(Europe, U.K., Australia and Singapore models)

VOLUME

Installing batteries in the remote control
Insert the batteries in the correct direction by aligning the + and marks on the batteries with the polarity markings (+ and ) inside the battery compartment.

I Notes on batteries

ADVANCED OPERATION ADDITIONAL INFORMATION
Change all of the batteries if you notice a decrease in the operating range of the remote control, that the indicator does not flash, or the light becoming dim. Do not use old batteries together with new ones. Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color. If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

APPENDIX

Press the part and slide off the battery compartment cover. Insert the 2 supplied batteries (AA, R06, UM-3) according to the polarity markings on the inside of the battery compartment. Slide the cover back on so that it snaps into place.
0102V430_1-8_EN(GB) 3 1/19/02, 8:03 PM

CONTROLS AND FUNCTIONS

Front panel

INPUT M0DE

NATURAL SOUND AV RECEIVER

RDS MODE/FREQ

STANDBY /ON

PTY SEEK MODE START

SILENT STEREO PROGRAM

Switch position

Speaker

Impedance level

REAR L (SURROUND)

MAIN CENTER REAR : 4MIN. /SPEAKER : 6MIN. /SPEAKER : 6MIN. /SPEAKER
The impedance of each speaker must be 4 or higher. The impedance must be 6 or higher. The impedance of each speaker must be 6 or higher. The impedance of each speaker must be 8 or higher. The impedance must be 8 or higher. The impedance of each speaker must be 8 or higher.
IMPEDANCE SELECTOR SET BEFORE POWER ON MAIN CENTER REAR : 8MIN. /SPEAKER : 8MIN. /SPEAKER : 8MIN. /SPEAKER

(U.S.A. model)

0103V430_9-19_EN(GB) 12 1/19/02, 8:03 PM

Center

CONNECTIONS
Before connecting components
Do not connect this unit or other components to the mains power until all connections between the components have been completed. Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, + to + and to. Some components require different connection methods and have different jack names. Refer to the operation instructions for each component to be connected to this unit. When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or changer), connect them to the jack with the same number labels as !, #, $ etc. YAMAHA applies this labeling system to all its products. After you have completed all connections, check them again to make sure they are correct. The name of jack corresponds to input selector.
DIGITAL INPUT jacks (pages 13-16) Video component jacks (pages 14-15)
I Connecting to digital jacks
This unit has digital jacks for direct transmission of digital signals through either coaxial or fiber optic cables. You can use the digital jacks to input PCM, Dolby Digital and DTS bitstreams. To enjoy multi-channel sound track of DVD software, etc. with DSP effect, you need to make digital connection. All digital input jacks are acceptable for 96-kHz sampling digital signals.
The OPTICAL jacks on this unit conform to the EIA standard. If you use a fiber optic cable that does not conform to this standard, this unit may not function properly.
PREPARATION BASIC OPERATION
SPEAKERS terminals (pages 10-11)
6CH INPUT jacks (page 18)
Antenna input terminals (page 17) (U.S.A. model)

DIGITAL INPUT

COAXIAL CD SURROUND MAIN

AM ANT

I VOLTAGE SELECTOR (China and General models)
The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/ 220/240 V AC, 50/60 Hz.
0103V430_9-19_EN(GB) 18 1/19/02, 8:03 PM

Turning on the power

When all connections are complete, turn on the power of this unit.
SLEEP 6CH INPUT DVD D-TV/CBL VCR
Press STANDBY/ON (POWER on the remote control) to turn on the power of this unit.
The level of the main volume, and then the current DSP program name appear on the front panel display.
Turn on the video monitor connected to this unit.
0103V430_9-19_EN(GB) 19 1/19/02, 8:03 PM

SPEAKER MODE SETTINGS

This unit has 5 SPEAKER SET items on the SET MENU that you must set according to the number of speakers in your configuration and their size. The following table summarizes these SPEAKER SET items, and shows the initial settings as well as other possible settings. If the initial settings shown in the following table are not appropriate for your speaker configuration, see 1 SPEAKER SET on pages 43-44 to change the settings. Summary of SPEAKER SET items 1A through 1E
Item Description Possible settings (default setting indicated in bold) LRG/SML/NON LARGE/SMALL LRG/SML/NON SWFR/MAIN/BOTH Nrm (Normal)/10 dB
1A CENTER 1B MAIN 1C REAR LR 1D BASS 1E MAIN Lv
Sets center speaker availability and size. Sets main speaker size. Sets rear L/R speakers availability and size. Sets the speaker(s) to be used to output low bass signals. Sets the main speaker level.
0104V430_20-22_EN(GB) 20 1/19/02, 8:03 PM
ADJUSTING SPEAKER OUTPUT LEVELS
This section explains how to adjust speaker output levels using the test tone generator. When this adjustment is complete, the output level heard at the listening position should be the same from each speaker. This is important for best performance of the digital sound field processor, and the various decoders (Dolby Digital, Dolby Pro Logic, Dolby Pro Logic and DTS).
Since this unit cannot enter the test mode while headphones are connected to this unit, be sure to unplug the headphones from the PHONES jack when using the test tone.
Set the BASS and TREBLE controls on the front panel to the center position and adjust the volume of this unit so you can hear the test tone. The test tone is heard (in order) from the main left speaker, center speaker, main right speaker, rear right speaker, rear left speaker, and the subwoofer. The tone is produced for 2.5 seconds from each speaker.

Using the test tone

Use the test tone to balance the output levels of the speakers. The adjustment of each speaker output level should be made at your listening position using the remote control.

BASS TREBLE

STEREO PROGRAM

SILENT

*SUBWOOFER

L SUR. R SUR.

3 1,4 2

STEREO EFFECT

* Subwoofer test tone is output after the rear left speaker (LEFT SURROUND).
The front panel display shows which speaker is outputting the test tone.
If the test tone cannot be heard, turn down the volume, set this unit to standby mode and check the speaker connections.
Press TEST to output the test tone.
0104V430_20-22_EN(GB) 21 1/19/02, 8:03 PM
Adjust the level of the effect speakers using +/ so that it matches the level of the main speakers. While adjusting, the test tone is heard from the selected speaker.
To adjust the level of the main speakers, use VOLUME knob (or VOLUME h/g on the remote control).
When adjustment is complete, press TEST to stop the test tone.
If 1A CENTER on the SET MENU is set to NON and the center speaker is not connected, the center channel sound is automatically output from the main left and right speakers. If 1C REAR LR on the SET MENU is set to NON, the output level of the rear left and right speakers cannot be adjusted in step 3. The test tone will be circulated skipping the rear right and left speakers. If 1D BASS on the SET MENU is set to MAIN, the test tone will be circulated skipping the subwoofer.
It is not necessary to readjust the speaker levels once they are set (as long as you do not change the speakers). You can enjoy listening to or watching the input source at the desired volume simply by adjusting the VOLUME knob (or VOLUME h/g on the remote control). If the output level of the effect speakers (center, rear left, and rear right) cannot be increased enough to match the level of the main speakers, set 1E MAIN Lv on SET MENU to 10 dB (see page 44). This setting decreases the main speaker output level to about one-third of the normal level. After you have set 1E MAIN Lv on the SET MENU to 10 dB, adjust the levels for the center and rear speakers again.

INPUT MODE

Input mode
In this mode, the input signal is selected automatically as follows: 1) Digital signal 2) Analog signal DTS: In this mode, only the digital input signal encoded with DTS is selected, even if another signal is input at the same time. ANALOG: In this mode, only the analog input signal is selected, even if a digital signal is input at the same time.
When AUTO is selected, this unit automatically determines the type of signal. If this unit detects a Dolby Digital or DTS signal, the decoder automatically switches to the appropriate setting. When playing a disc encoded with Dolby Digital or DTS on some LD or DVD players, the sound output delays for a moment when playback resumes after a search because the digital signal is selected again. When playing a LD source that has not been digitally recorded, the sound may not be output for some LD players. In this case, set the input mode to ANALOG.
0105V430_23-28_EN(GB) 25 1/19/02, 8:04 PM
Selecting a sound field program
You can enhance your listening experience by selecting a DSP program. For details about each program, see pages 29 to 33.
After selecting the desired program, press the same button repeatedly to select the desired sub-program if available. Example: Pressing MOVIE THEATER 1 repeatedly switches the sub-program between Sci-Fi and Spectacle.

PROGRAM l / h

Program name
VCR V-AUX D-TV/CBL DVD MD/CD-R TUNER CD

DIGITAL

MOVIE THTR 1

DGTLzSci-Fi

Sub-program name

C R RR

LFE RL
There are 9 programs with sub-programs available with this unit. However, the selection depends on the input signal format and not all sub-programs can be used with all input signal formats. The digital sound field processor cannot be used when a source connected to the 6CH INPUT jacks of this unit is selected or when 96-kHz sampling digital signals are input to this unit. The acoustics of your listening room affect the DSP program. Minimize the sound reflections in your room to maximize the effect created by the program. When you select an input source, this unit automatically selects the last DSP program used with that source. When you set this unit in the standby mode, the current source and DSP program are memorized and are automatically selected when you turn on the power again. If a Dolby Digital or DTS signal is input when the input mode is set to AUTO, the DSP program (No. 79) automatically switches to the appropriate decoding program. When a monaural source is being played with PRO LOGIC/ Normal or PRO LOGIC/Enhanced, or PRO LOGIC Movie, no sound will be heard from the main speakers and the rear speakers. Sound can only be heard from the center speaker. (If 1A CENTER on the SET MENU is set to NON, the center channel sound is output from the main speakers.)

I Dolby Pro Logic + DSP sound field effect

Surround DSP sound field

Most movie software has 4-channel (left, center, right, and surround) sound information encoded by Dolby Surround matrix processing and stored on the left and right tracks. These signals are processed by the Dolby Pro Logic decoder. The MOVIE THEATER programs are designed to recreate the spaciousness and delicate nuances of sound that tend to be lost in the encoding and decoding processes.

I Dolby Pro Logic

Dolby Pro Logic decodes Dolby Surround software into 5 discrete full-range channels (3 channels in front and 2 channels in rear). There are 2 modes; MOVIE for movies and MUSIC for 2-channel audio sources.
0106V430_29-33_EN(GB) 31 1/19/02, 8:05 PM

CINEMA-DSP programs

I For movie programs: No. 7 to 9
This unit automatically chooses the appropriate decoder and DSP sound field pattern according to the input signal format. Table of Program Names for Each Input Format
Input 2 channel Stereo No. 7 Program MOVIE THEATER mm Spectacle 70 mm Sci-Fi 8 MOVIE THEATER mm Adventure 70 mm General 9 DOLBY DIGITAL DTS DIGITAL SUR PRO LOGIC Normal Enhanced PRO LOGIC Movie Music DGTL Spectacle DGTL Sci-Fi DGTL Adventure DGTL General Normal Enhanced DTS Spectacle DTS Sci-Fi DTS Adventure DTS General Normal Enhanced 5.1 channel DOLBY DIGITAL DTS 6.1 channel * DOLBY DIGITAL Matrix 6.1 Spectacle 6.1 Sci-Fi 6.1 Adventure 6.1 General 6.1 Matrix 6.1 Enhanced 6.1 DTS Matrix 6.1 Spectacle 6.1 Sci-Fi 6.1 Adventure 6.1 General 6.1 Matrix 6.1 Enhanced 6.1
* means the Matrix 6.1 decoder is ON.
If a Dolby Digital signal or DTS signal is input when the input mode is set to AUTO, the DSP program will automatically switch to the Dolby Digital playback sound field or DTS playback sound field. If Dolby Digital Surround EX software or DTS ES software is played when AUTO is selected by pressing the MATRIX 6.1 button on the remote control, the Dolby Digital + Matrix 6.1 or DTS + Matrix 6.1 decoder usually turns on and the corresponding DSP program is selected. MATRIX 6.1 on the remote control can be used to play Dolby Digital or DTS 5.1 channel sources with the virtual rear center speaker. In this case the program name changes to the corresponding name for 6.1 channel. When playing a 6.1 channel source with MATRIX 6.1 on the remote control turned off, the program name changes to the corresponding name for 5.1 channel.

Sci-Fi

MOVIE THEATER 2

Adventure

General

Enhanced Mode

I For audio-video sources: No. 4 to 6
No. 4 Program ENTERTAINMENT/ Game ENTERTAINMENT/ Concert Video 5 TV SPORTS Features
This program adds a deep and spatial feeling to video game sounds.
This program adds a deep and spatial feeling to concert video sounds.
With this program, you can enjoy watching various TV programs such as news, variety shows, music programs or sports programs. In a stereo broadcast of a sports game, the commentator is oriented at the center position, and the shouts and the atmosphere in the stadium spread on the surround side, while their spread to the rear is properly restrained. This program is provided for reproducing monaural video sources (such as old movies). The program produces the optimum reverberation to create sound depth by using only the presence sound field.
0106V430_29-33_EN(GB) 33 1/19/02, 8:05 PM

TUNING

Automatic and manual tuning
There are 2 ways to tune; automatic and manual. Automatic tuning is effective when station signals are strong and there is no interference.
Press PRESET/TUNING l / h once to begin automatic tuning. Press h to tune in to a higher frequency, or press l to tune in to a lower frequency.

I Automatic tuning

When tuned in to a station, the TUNED indicator lights up and the frequency of the received station is shown on the front panel display.
Use the manual tuning method if the tuning search does not stop at the desired station because the signal is weak.

I Manual tuning

If the signal from the station you want to select is weak, you must tune in to it manually.
Press INPUT l / h (TUNER on the remote control) to select TUNER as the input source.
Select TUNER and the reception band following steps 1 and 2 described in Automatic tuning at left. Press TUNING MODE (AUTO/MANL MONO) so that the AUTO indicator goes off from the front panel display.
CD TUNER MD/CD-R PRESET + A/B/C/D/E

Goes off

If the colon (:) appears on the front panel display, press PRESET/TUNING (EDIT) to turn it off.
Press FM/AM to select the reception band. FM or AM appears on the front panel display.
Press TUNING MODE (AUTO/MANL MONO) so that the AUTO indicator lights up on the front panel display.
Press PRESET/TUNING l / h to tune in to the desired station manually. Hold down the button to continue the tuning search.

AUTO Lights up

Manually tuning in to an FM station will automatically change the reception mode to monaural to increase the signal quality.
0107V430_34-41_EN(GB) 34 1/19/02, 8:05 PM

Presetting stations

I Automatically presetting stations (for FM stations)
You can use the automatic preset tuning feature to store FM stations. This function enables this unit to automatically tune in to FM stations with strong signals, and to store up to 40 (8 stations x 5 groups) of those stations in order. This feature enables you to easily tune in to any preset station by selecting the preset station number (see page 37).
Any stored station data existing under a preset number is cleared when you store a new station under that preset number. When a station data is stored under a preset number, the frequency and reception band are also stored. You can manually replace a preset station with another FM or AM station by simply following the procedure in the section Manually presetting stations on page 36. If the number of the received stations does not reach E8, automatic preset tuning has automatically stopped after searching all stations. Only FM stations with sufficient signal strength are stored automatically by automatic preset tuning. If the station you want to store is weak in signal strength, tune in to it manually in the monaural mode, and store it by following the procedure in Manually presetting stations on page 36.
Press FM/AM to select the FM band.
Automatic preset tuning options You can select the preset number from which this unit will store FM stations and/or begin tuning toward lower frequencies. After pressing MEMORY in step 3: 1. Press A/B/C/D/E and PRESET/TUNING l / h to select the preset number under which the first station will be stored. Automatic preset tuning will stop when stations have all been stored up to E8. 2. Press PRESET/TUNING (EDIT) to turn off the colon (:) and then press PRESET/TUNING l to begin tuning toward lower frequencies. Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cord is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the preset stations may be cleared. If so, store the stations again.

Press +/ to adjust the speaker output level. The control range for the center or rear left and right speakers is from +10 dB to 10 dB. The control range for the subwoofer is from 0 dB to 20 dB.
When the speaker output modes for 1A CENTER and 1C REAR LR are set to NON, and 1D BASS to MAIN, the output level of those speakers cannot be adjusted because there is no sound coming from these speakers. When you adjust the output level with LEVEL, the settings you made with the test tone will be changed. We recommend adjusting the speakers by following the steps described in Using the test tone on pages 21 and 22.
Press LEVEL repeatedly to select the speaker(s) you want to adjust. Each time you press LEVEL, the selected speaker changes and appears on the front panel display as follows: center, rear right, rear left and subwoofer.

I For 5ch Stereo

You can adjust the volume level for each channel in 5channel stereo mode. Control range: 0 to 100% CT level (Center level) RL level (Rear left level) RR level (Rear right level)
Center speaker output level
Select 5ch Stereo. Press u / d repeatedly to select the speaker(s) you want to adjust.
Rear right speaker output level Rear left speaker output level
Press +/ to adjust the speaker output level.

Subwoofer output level

Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is in the standby mode. However, if the power cord is disconnected from the AC outlet, or the power supply is cut for more than one week, the stored data will be lost. If so, set the output level again.
Once you press LEVEL, you can also select the speaker(s) to be adjusted by pressing d / u.
0109V430_47-49_EN(GB) 47 1/19/02, 8:05 PM

ADJUSTING THE DELAY TIME

You can adjust the time difference between the beginning of the sound from the main speakers and the beginning of the sound effect from the rear speakers. The larger the value, the later the sound effect is generated. The delay time can be individually adjusted to all DSP programs. The following table shows factory-set delay time.
Program CONCERT HALL JAZZ CLUB ROCK CONCERT DISCO GAME CONCERT VIDEO TV SPORTS MONO MOVIE 70 mm SPECTACLE DGTL SPECTACLE DTS SPECTACLE Spectacle 6.mm SCI-FI Sci-Fi 6.1 DGTL SCI-FI DTS SCI-FI 70 mm ADVENTURE DGTL ADVENTURE DTS ADVENTURE Adventure 6.mm GENERAL DGTL GENERAL DTS GENERAL General 6.1 PRO LOGIC/NORMAL DOLBY DIGITAL/NORMAL DTS DIGITAL SUR./NORMAL Matrix 6.1 PRO LOGIC/ENHANCED DOLBY DIGITAL/ENHANCED DTS DIGITAL SUR./ENHANCED Enhanced 6.1 PRO LOGIC Movie PRO LOGIC Music Preset value (ms) 15 5

1. 2. 3. 4.

5. 6. 7.
Select a DSP program you want to adjust the delay time. Press u / d so that DELAY appears on the front panel display.
Press +/ to adjust the delay time.
Adding too much delay will cause an unnatural effect with some sources. The sound is momentarily interrupted while adjusting the delay time.
Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is in the standby mode. However, if the power cord is disconnected from the AC outlet, or the power supply is cut for more than one week, the stored data will be lost. If so, adjust the delay time again.
0109V430_47-49_EN(GB) 48 1/19/02, 8:06 PM
ADJUSTING THE PARAMETER SETTINGS FOR PRO LOGIC
Changing parameter settings
You can adjust the values of PRO LOGIC Music parameters so the sound fields are recreated accurately in your listening room. Adjustments should be made with the remote control.
PRO LOGIC Music parameter descriptions

I PANORAMA

Function: Turning the function on extends the front stereo image to include the surround speakers for wraparound effect. OFF/ON, initial setting is OFF.

Choices:

I DIMENSION 1
Function: Gradually adjusts the soundfield either towards the front or towards the rear. Control range: 3 (towards the rear) to +3 (towards the front), initial setting is STD (standard).
I CT WIDTH (Center width) 3
Function: Adjusts the center image from all three front speakers to varying degrees. The larger the value, adjusts the center image towards the main left and right speakers. Control range: 0 (center channel sound is output only from center speaker) to 7 (center channel sound is output only from main left and right speakers), initial setting is 3.

Select PRO LOGIC

Music.
Press u / d to select the parameter.
Press +/ to change the parameter value.
Repeat steps 2 and 3 above as necessary to change other parameters.
You cannot change parameter values when 10 MEM. GUARD on the SET MENU is set to ON.
Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cord is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the parameter value you edited will return to the factory setting. If so, edit the parameter value again.
0109V430_47-49_EN(GB) 49 1/19/02, 8:06 PM

The internal microcomputer has been frozen by an external electric shock (such as lightning or excessive static electricity) or by a power supply with low voltage. Speaker cables are short circuited.
Disconnect the AC power cord from the outlet and then plug it in again after about 30 seconds.
CHECK SP WIRES appears on the front panel display. There is noise interference from digital or high-frequency equipment, or this unit. This unit suddenly turns into the standby mode.
Make sure all speaker cables are connected correctly.
This unit is too close to the digital or high-frequency equipment.
Move this unit further away from such equipment.
The internal temperature becomes too high and the overheat protection circuitry has been activated.
Wait until this unit cools down and then turn it back on.
0110V430_50-56_EN(GB) 52 1/19/02, 8:06 PM

I Tuner

FM stereo reception is noisy.
The characteristics of FM stereo broadcasts may cause this problem when the transmitter is too far away or the antenna input is poor.
Check the antenna connections. Try using a high-quality directional FM antenna. Use the manual tuning method.
There is distortion, and clear reception cannot be obtained even with a good FM antenna. The desired station cannot be tuned in with the automatic tuning method. Previously preset stations can no longer be tuned in. The desired station cannot be tuned in with the automatic tuning method.
There is multipath interference.
Adjust the antenna position to eliminate multipath interference.

The station is too weak.

Use a high-quality directional FM antenna. Use the manual tuning method.
This unit has been disconnected for a long period.

Re-store the stations.

35, 36
The signal is weak or the antenna connections are loose.
Tighten the AM loop antenna connections and orient it for best reception. Use the manual tuning method.
There are continuous crackling and hissing noises. There are buzzing and whining noises (especially in the evening).
Noises result from lightning, fluorescent lamps, motors, thermostats and other electrical equipment. A TV set is being used nearby.
Use an outdoor antenna and a ground wire. This will help somewhat, but it is difficult to eliminate all noise. Move this unit away from the TV.

I Remote control

The remote control does not work nor function properly.

Wrong distance or angle.

The remote control will function within a maximum range of 6 m (20 feet) and no more than 30 degrees off-axis from the front panel. Reposition this unit.

NS-P230 NEW PRODUCT BULLETIN
Digital Home Cinema 5.1-Channel Speaker System

NS-P230

Compact, Complete Digital Home Cinema 5.1-Channel Speaker Package. Excellent Sound Quality and Smart, Clean, Matching Design. Ideal Combination with Yamaha Affordable Range Digital Home Cinema Receivers.
Realizes the Full Potential of Multi-Channel Audio Sources.

1/4 (W)

The Convenient, Contemporary Way to Begin Enjoying the Full Benefits of 5.1-Channel Home Cinema Entertainment.
Ideal combination for 5.1-channel movie sound formats 6-speaker package consisting of 4satellite (main L/R, rear L/R), centre speakers and subwoofer Excellent sound quality and smart, compact design. Advanced YST subwoofer for powerful bass response. Dual 5cm (2) full-range drivers for high sound quality (4 satellites and centre) Flexible placement Magnetic shielding allows placement near a TV.
NS-P230 Main Specifications Package Includes 4 Satellite (Main Left/Right and Rear Left/Right) and Centre Speakers and Subwoofer Advanced YST (Advanced Yamaha Active Servo Technology) Subwoofer for Powerful Bass Response Magnetic Shielding Allows Placement Near the TV (All Speakers) Wide Range System Frequency Response (30 25,000 Hz) 4 Satellite Speakers (Main L/R and Rear L/R) Acoustic Suspension Design Dual 5cm (2) Full-Range Drivers Input Power (Max/Nominal): 100 W/30 W Sensitivity: 86 dB/2.83 V/m Impedance: 6 ohms Dimensions (W x H x D): 72 x 164 x 111 mm; 2-13/16 x 6-7/16 x 43/8/unit Weight: 0.9 kg; 2 lbs./unit Centre Speaker Acoustic Suspension Design Dual 5cm (2) Full-Range Drivers Input Power (Max/Nominal): 100 W/30 W Sensitivity: 86 dB/2.83 V/m Impedance: 6 ohms Dimensions (W x H x D): 300 x 72 x 110 mm; 11-13/16 x 2-13/16 x 4-5/16 Weight: 1.2 kg; 2.7 lbs. Subwoofer Advanced YST for Powerful Bass Response Output Power: 50 W (5 ohms) [US and Canadian models: 55 W] 16cm (6) Multi-Range Driver Auto Standby with Sensitivity Selector Two Input Connections: Speaker Level or Line Level (pin jack) Dimensions (W x H x D): 200 x 365 x 375 mm; 7-7/8 x 14-3/8 x 14-3/7 Weight: 8.5 kg; 18.7 lbs.
Digital Home Cinema 5.1-Channel Speaker Package
The NS-230 is also offered with a silver and black finish in some areas.

2/4 (W)

Designed for Use in 5.1-Channel Home Cinema Systems
This speaker package is designed for use in a 5.1-channel (6speaker) system. This configuration allows Dolby Digital and DTS movie sound formats to be enjoyed at their full potential. The speakers high performance capabilities ensure accurate reproduction of DVD and other high quality sound sources, as well as of Yamahas dynamic and realistic CINEMA DSP sound.
Enjoy Home Cinema Surround Sound at Its Best with an All-Yamaha System.
If the NS-P230 speaker package sounds like a good idea, wait until you hear it matched with a Yamaha Home Cinema Amplifier or Receiver and DVD Player. These components give you the unique sonic benefits of CINEMA DSP and a wide range of music and movie surround programmes, plus the full 5.1-channel Dolby Digital or DTS Digital Surround movie sound experience. With an all-Yamaha system, you get top quality sound, easy connections, and stylish components that look good in any setting

5.1-Channel System

5.1-Channel Compatible Amplifier/Receiver DVD Player NS-P230
5.1-Channel Speaker Package
By combining a Yamaha 5.1-channel receiver such as the RX-V430 (RDS) with the NS-P230, you can also enjoy the latest 6.1-channel movies. The receiver has a rear centre Phantom mode so you can hear Dolby Digital EX and DTS-ES movie sound formats, and even enjoy Yamaha's exciting QuadField CINEMA DSP surround sound.
The NS-P230 5.1-Channel Speaker Package constructs 4 satellite (main L/R and rear L/R), centre and LFE (Low Frequency Effect i.e. subwoofer) channel speakers.
Optional Speaker Stands: SPS-80
650900 mm (25-5/835-1/2) Height Adjust Not available in some areas.
Good Speakers Are Important for Good Home Cinema.
Main Speakers Required to handle most of the sound output, these speakers require excellent sensitivity, frequency response and dynamic range. Centre Speaker The centre speaker delivers most of the dialogue, so high clarity output is vital to movie enjoyment. Rear Speakers The quality of the surround sound experience depends on the quality of the rear speakers. Yamaha ensures that they perform up to high standards. Subwoofer Because good bass response is necessary for enjoying movie sound, Yamaha Advanced YST subwoofers are ideal for use in digital home cinema systems.

3/4 (W)

High Sound Quality Speakers
4 Satellite Speakers and 1 Center Speaker High Performance Dual 5cm (2) Full-Range Drivers These speakers use high quality parts to achieve excellent performance. They have 45mm (1-3/4) dual ferrite magnets with shielded cases for maximum power and copper center pole caps for low distortion. Kapton bobbins contribute to high S/N ratio. Unwanted vibrations are prevented by a heavy-duty steel frame and a parallel-surface cabinet design. Even the wiring is an antiresonance type. Subwoofer Advanced YST for Powerful Bass Response Advanced Yamaha Active Servo Technology (Advanced YST) is a unique system in which the speaker and amplifier work together to cancel out impedance so the speaker unit has a perfectly linear motion. Advanced YST helps to ensure the highest levels of sound pressure and overall performance.
For details please contact:
Dolby Digital and Double D are trademarks of Dolby Laboratories Corporation. DTS and DTS Digital Surround are trademarks of Digital Theater Systems, Inc. Product designs and specifications are subject to change without notice.
Visit us at our website: http://www.yamaha.co.jp/

YAMAHA CORPORATION

P.O. Box 1, Hamamatsu, Japan

APB601-NSP230@620

4/4 (W)