Specialty Tools Hot-Start Kit For Yamaha Ratchet Spark Plug HANDLEBARS YZ/WR 400F 121-01703 Wrench 121-08147 space STREET LEVERS Designed specically to t where there is limited
PAINT FORK SEALS CABLES SUSPENSION ELECTRICAL FILTERS BRAKE LINES BRAKES CABLE MAKING SUPPLIES CONTROLS DUAL SPORT MANUALS FSO PRODUCTS EMGO DRIVE DISPLAY JETS BEARINGS EYEWEAR VINTAGE MIRRORS EUROPEAN KICKERS SHIFTERS MISC HARD PARTS SHOP TOOLS CHEMICALS TOOLS

REV. 03-15-06

Prompted by the introduction of the YZ/WR400F, we have designed this Hot Start Kit to relocate the hot start button from the left side of the bike to the handlebars. This kit is very convenient and will make the juggling act of starting your 98-99 YZ/WR400F much simpler. Attaches easily to your Bar Clamps.
Ratchet mechanism works one way Fits standard 13/16 plugs
Blaster Rear Brake Kits 121-01298 121-01299
YFS200 Blaster 88-98 This cable will eliminate the stock cable from the handlebar. Cable will go from the rear brake pedal to the caliper.

FCR Carb Tool 121-08181

Contains longer bits for reaching into recessed cavities to adjust Keihin FCR carburetors Ideal for trail riders and garage mechanics alike Includes 6mm hex for main jets, long-reach straight slot for pilot jets & a 3mm Allen for oat bowl removal
Same as 121-01298 +4 Cable is 4 longer for extended swingarms.

121-01027 Replacement

(626) 792-7384 www.FlandersCompany.com
Fax: (626) 792-5341 www.FlandersCo.com
Specialty Tools Snap Ring Pliers 121-08-0186 Swingarm Bearing Tool 121-080213

INDEX PAINT

HANDLEBARS
Economical pliers that easily work with both inside and outside opening snap rings or clips Includes 3 extra sets of tips, 1 additional straight tip and 2 offset or angled tips
Designed for installation of the swing arm bearings on late model STREET LEVERS Japanese motorcycles FORK SEALS Using the correct size insert (various sizes included in kit) and the puller, the mechanic can draw the bearing into the swingarm CABLES without beating on it with a hammer SUSPENSION ELECTRICAL FILTERS BRAKE LINES BRAKES

CABLE MAKING SUPPLI

Main Jet Wrenches
High-quality die cast construction 6mm round and hex jets and 8mm round Cap holds a few spare main jets Sold each
CONTROLS DUAL SPORT MANUALS

FSO PRODUCTS

121-08023 6mm Hex

(Fits 6mm hex main jets)

121-08024 8mm Round
(Fits 8mm round main jets)
Allen Extension 121-080184
EMGO DRIVE DISPLAY JETS BEARINGS EYEWEAR VINTAGE MIRRORS EUROPEAN KICKERS SHIFTERS MISC HARD PARTS SHOP TOOLS CHEMICALS TOOLS

121-08025 6mm Round

5mm allen on a 6.25 long, 38-drive extension for hard-to-reach case bolts Designed for use with air tools Great for splitting engine cases
(Fits 6mm round main and pilot)

Specialty Tools

INDEX PAINT HANDLEBARS STREET LEVERS FORK SEALS CABLES SUSPENSION ELECTRICAL FILTERS BRAKE LINES BRAKES CABLE MAKING SUPPLIES CONTROLS DUAL SPORT MANUALS FSO PRODUCTS EMGO DRIVE DISPLAY JETS BEARINGS EYEWEAR VINTAGE MIRRORS EUROPEAN KICKERS SHIFTERS MISC HARD PARTS SHOP TOOLS CHEMICALS TOOLS
Spark Plug Socket 121-08175
Specially designed for Honda XR400s as a trail tool but ts many models with 18mm plugs The socket is designed to t into the plug cavity and allow the user to choose between the Motion Pro spark plug ratchet wrench, a 38 ratchet or 1316 wrench as well as a Tool Kit bar or Phillips screwdriver through a 8.5mm hole for removal and installation Other Applications: Honda: XR400R 96-00, XR500R 83-84, XR600R 85-00, XR650L 93-00, TRX300 88-91, TRX400EX 99, TRX400FW 96-99, TRX400ES 2000, Kawasaki: KLF400 93-96, KTM: 400SXC 2000, 620LC4 96-97, 620SX 97-98, 640 LCA 99, Suzuki: LT160E 90-92, Yamaha: YFM250 99-00, YFM350X 86-88 & 90-99, YFM600, XT225 92-00, TTR225 99-00, TT600 83-86

Mini-T Carb Tool 121-08136
Perfect for on-the-trail jet changes Will t into your fanny pack Includes #2 Phillips bit, #1 Straight-slot bit and 6mm hex socket Can store up to 3 main jets in handle Specically designed for 4-strokes Will also work with many 2-stroke models
Carb Adjusting Tool 121-08022
Made from alloy steel Works with Mikuni or Keihin carburetors featuring an 8mm hex nut and screwdriver-slot adjusting bolt 11 inches long
Ball End Allen Set 121-080185
Pilot Screw Adjusting Tool 121-08119
1 angled head Length is 17 with a at slot blade tip Designed for those hard-to-reach areas on most multi-cylinder motorcycles
Made of chrome-vanadium tool steel Sizes available 1.5, 2, 2.5, 3, 4, 5, 6, 8 & 10 mm Ball end allows for better access to allen-head bolts (up to 25 degree working angle) Convenient holder included
Specialty Tools Deluxe Carb Tuner 121-08009 Deluxe Auxiliary Fuel Tank
(for fuel-injected machines)
Rugged, impact-resistant polycarbonate body Hose, mercury, line restrictors and 5mm adapters are included For use with any 2-, 3-, or 4-cylinder motorcycles 5mm adapters are used on Honda and Suzuki models Optional 6mm adapters are available for use on most Yamaha models Most Kawasaki models do not need adapters

121-08189

STREET LEVERS FORK SEALS CABLES SUSPENSION ELECTRICAL FILTERS BRAKE LINES BRAKES
Redesigned to be used on new fuel-injected motorcycles as well as standard carburetor bikes The petcock has been upgraded for easier opening and closing The bottle has been correctly graduated for those who want to measure exact amounts of gear oil or other uid
Not recommended for 2-stroke motors
Instructions included Made in the U.S.A.
121-08013 5mm brass adapters (set of 4) Hon/Suz 121-08040 6mm brass adapters (set of 4) Yam 121-08012 Mercury Rell 121-08014 Replacement Hose Set Auxiliary Fuel Tank 121-08032
CABLE MAKING SUPPLI CONTROLS DUAL SPORT MANUALS
FSO PRODUCTS EMGO DRIVE DISPLAY JETS BEARINGS EYEWEAR VINTAGE MIRRORS EUROPEAN KICKERS SHIFTERS MISC HARD PARTS SHOP TOOLS CHEMICALS TOOLS

For use when tuning a motorcycle with the gas tank removed Use in place of regular tank while running engine Includes 4 feet of 1/4 fuel line and an in-line petcock On fuel-injected motorcycles, use a T-Fitting and second fuel valve for return fuel Tank can also be used for relling transmission oil in late model motocross bikes
Economy Carb Tuner 121-08010
Sheet steel body with easy-to-read markings Includes mercury, hoses, 5mm adapters, line restrictors and easy to follow instructions

INDEX PAINT HANDLEBARS

STREET LEVERS Used to remove exhaust pipe springs, seat or tank holding springs, cotter pins, side stand springs and other parts FORK SEALS Made in the U.S.A. CABLES SUSPENSION ELECTRICAL FILTERS BRAKE LINES BRAKES CABLE MAKING SUPPLIES CONTROLS DUAL SPORT MANUALS FSO PRODUCTS EMGO DRIVE DISPLAY JETS BEARINGS EYEWEAR VINTAGE MIRRORS EUROPEAN KICKERS SHIFTERS MISC HARD PARTS SHOP TOOLS CHEMICALS TOOLS
Heavy Duty Spring Hook 121-08127
Std. Spring Hook 121-08065
Used to remove exhaust pipe springs, seat or tank holding springs, cotter pins, side stand springs and other parts Made in the U.S.A.

Stud Installation Tools

Will install cylinder studs on most motorcycles Hex head is 3/4 or 19mm Sold individually and in a set with three metric sizes Made in the U.S.A.
Piston Pin Tool 121-08068
121-08148 3/8 x 16 Stud Tool 121-08149 6mm x 1.00 Stud Tool 121-08150 8mm x 1.25 Stud Tool 121-08151 10mm x 1.25 Stud Tool 121-08152 (6, 8 & 10mm) Set of 3
Aids in removing and installing piston pins Fits all piston sizes from 40mm (1-5/8) to 100mm (4) and all piston pins from 12mm (1/2) to 25mm (1), including all singlecylinder engines from 50cc to 600cc and all 2-, 3-, & 4-cylinder models Will not damage piston during removal Made in the U.S.A.
Clutch Holding Tool 121-08-008
Made from medium carbon steel with hardened jaws Hold clutch hubs, ywheels, gears, sprockets, etc. Jaws open up to 5 wide
Specialty Tools Bead Buddy Off-Road Tire Tool 121-08187
Used to push the tire bead down into the drop center of the rim on off-road wheels while using tire tools to change tires Hook over spoke and push bead down on opposite side of tire from tire irons No more ghting to keep bead down while installing off-road
Torque Wrench Adapter 121-08134
Chrome-vanadium tool steel with satin-chrome nish Properly torque two-stroke cylinder base nuts Will t 12mm and 14mm nuts Extends the reach of 3/8 drive torque by 3 Chart supplied Check owners manual for proper torque specications
FSO PRODUCTS EMGO DRIVE DISPLAY JETS
Valve Core Remover 121-080183
Made from hex stock Allows for easy removal and installation of standard valve cores in tubed or tubeless valve stems This will be the most borrowed tool in the service department!

Hydraulic Brake Bleeder 121-08143
Make bleeding your brakes a one-person job. Instructions included Made in the U.S.A.
BEARINGS EYEWEAR VINTAGE MIRRORS EUROPEAN KICKERS SHIFTERS MISC HARD PARTS SHOP TOOLS CHEMICALS TOOLS
INDEX PAINT CAD-II plated carbon steel HANDLEBARS Split design STREET LEVERS Many sizes available Each driver is approximately 25oz. FORK SEALS Sold individually CABLES SUSPENSION ELECTRICAL FILTERS BRAKE LINES BRAKES CABLE MAKING SUPPLIES CONTROLS DUAL SPORT MANUALS FSO PRODUCTS EMGO DRIVE DISPLAY JETS BEARINGS EYEWEAR VINTAGE MIRRORS EUROPEAN KICKERS SHIFTERS MISC HARD PARTS SHOP TOOLS CHEMICALS TOOLS

Fork Seal Drivers

Damper Rod Fork Tool 121-08117
121-08170 39mm 121-08123 41mm 121-08124 43mm 121-08125 45mm 121-08138 46/47mm combo 121-08171 49/50mm combo
Hardened steel with black nish Aid assembly and disassembly of most 41, 43, & 46mm Kayaba and Showa inverted forks Not required on the 91-92 Honda CR models
Fork Oil Level Gauge 121-08121
For checking and adjusting the oil level on any conventional or inverted fork Adjustable ring will measure from 0-300mm Syringe has a capacity of 60ml
Nitrogen Shock Gauge & Nitrogen Needle Kit Filler 121-08072 121-08075
Calibrated to 300 psi Bleeder valve and T-handle plunger pin chuck Swivel chuck has a 12 exible hose Instructions, carrying box and Schrader valve extension included Required on some Showa shocks Made in the U.S.A.
Nitrogen needle is use to ll shocks with self-sealing rubber valves (Some Yamaha & Ohlins) Can be used in conjunction with a nitrogen bottle and regulator or to our Nitrogen Shock Gauge Instructions included Made in the U.S.A.
121-08B75 Replacement Needle
Safety Wire & Twisters

Safety Lock Wire

Stainless steel safety lock wire that resists work hardening and meets government specications. 360 ft. roll in unique dispenser that saves waste and is easier to handle 528-01020.020 528-01047.047 528-01032.032 (Most common)

STREET LEVERS FORK SEALS CABLES

Safety Wire Starter Kit

SUSPENSION ELECTRICAL FILTERS BRAKE LINES BRAKES

Wapid Wire Winder

352-02777 Heres an economical way to wind a perfect braid of safety wire every time. At 1/6 the price of safety wire pliers this item belongs in every tool box! Designed to use standard.032 safety wire, our W.W.W. ts into small places, is easy to use and durable.
352-02400 Includes: *25 feet.032 stainless steel safety wire. *18 safety washers. *1 wapid wire winder

Econo Winding Kit

352-02401 Includes: *25 feet.032 stainless steel safety wire. *1 wapid wire winder (No washers)

RPS Safety Wire

Safety Wire Washers
FSO PRODUCTS EMGO DRIVE DISPLAY JETS BEARINGS EYEWEAR VINTAGE MIRRORS EUROPEAN KICKERS SHIFTERS MISC HARD PARTS SHOP TOOLS
352-02413.032 stainless steel safety wire packaged in a 25-foot roll for your convenience. No more Bailing Wire Breakage Syndrome, use the real thing! This wire securely fastens hand grips, nuts, bolts, caps and just about everything
352-washers; 6 of each size. The tabs on our RPS Safety Wire Washers fold up to grip nut or bolt heads securely. After the tabs are folded up, Safety wire is inserted through the hole in the longest tab and secured to a stationary object. Packaged on a blister card with as assortment of the three most popular sizes; 6, 8 and 10mm.
401-03819 - 9 401-03816 - 6.75 Made from alloy steel forgings, these SAFETYTWIST pliers offer the user rigid construction, tapered jaws, nely nished cutting edges and a new long life twist mechanism. The induction hardened cutting jaws will cut safety wire up to.060 diameter, or two twisted strands of.041 dia. wire. Tapered jaws allow easy access into conned areas. Specially nished jaw faces provide for maximum grip-minimum slip, on the wire being twisted.

Safety Wire Twister

Helpful Hints For Twisting Your Wire
Lockwire should be installed only one at a time. If the wire is removed, for any reason, it should be destroyed. Kinks and sharp bends should not be made in lockwire.
Lockwire should be as short as possible, attached in the most direct way using the two (2) wire only and installed so the lockwire tends to tighten the bolt or nut. The ends of the wire should have a minumum of three (3) turns. Three (3) turns Minimum

Three (3) turns Minimum

CHEMICALS TOOLS
Circuit Testers, Point Files
Electronic Ignition Spark Tester
566-23000 Specially calibrated to re only when the elctronic ignition is generateing adequate voltage. Checks output at the coil and each spark plug wire. With this special spark tester you can tell in seconds if an electronic ignition is functioning properly. Just insert it into the distributir end of the coil wire or a spark plug wire and crank the engine: A spark indicates proper ignition voltage ooutput

Circuit Tester

715-01030 6-12 volt. Checks hot lines, open circuits, loose connections, burned-out bulbs, etc. Makes trouble shooting fast & easy. Works off vehicles battery
Battery Powered Circuit Tester
715-01050 Test circuits with vehicle power off. Checks switches, fuses, relays, points, etc. Battery included

Rimac Flex-Stone

715-grit exible, ne grit and narrow for motorcycle points in hard to reach areas. Sold in pack of 12 Order 1 pack
Motorcycle Flexible Ignition Point File
531-01295 Made of super hard aluminum oxide impregnated in a exible core. Bends easily to reach ignition points in hard to reach areas. Non conductive electrically
Leak Tester & Truing Stand

Leak Down Tester

121-08071 Leak down tester for checking possible air leaks on 2 stroke engines. Air leaks through seals or gaskets can cause serious problems with improper air mixture. This is the main cause of piston seizure, detonation or improper carburetor jetting. Motion Pro tester is complete with air pressure gauge, pump up bulb and all ttings and adaptors for single and twin cylinder 2 cycle motorcycle engines. Packed in a handy carrying box. With instructions.
STREET LEVERS FORK SEALS CABLES SUSPENSION ELECTRICAL FILTERS

Truing Stand

BRAKE LINES BRAKES
560-91284 Truing stand. 560-91299 Extra dial arm Compact versatile truing stand for checking alignment of crankshaft, fork tubes, etc. with dial indicator. Dial must be ordered seperately. Unit has following features: 1. 7-1/2 maximum bearing height allowing 15 swing (diameter of ywheel) permitting rotation of many crankshafts without rods striking base. 2. 17-1/4 working length maximum. 3. 2-1/2 minimum width 4. 5/8 vertical adjustment for offset bearing diameters. 730-43411 0-25mm, reads.01mm, 2 1/4 dia. face. Stem or back mount

FSO PRODUCTS EMGO DRIVE

730-43450 0-1 inch, reads.001, 2 1/4 dia. face. Back mount only
DISPLAY JETS BEARINGS EYEWEAR VINTAGE MIRRORS EUROPEAN KICKERS SHIFTERS MISC HARD PARTS SHOP TOOLS CHEMICALS TOOLS