Reviews & Opinions
Independent and trusted. Read before buy Yanmar 3GMD!

Yanmar 3GMD

Manual

Download (English)
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Yanmar 3GMDAbout Yanmar 3GMD
Here you can find all about Yanmar 3GMD like manual and other informations. For example: parts.

Yanmar 3GMD manual (user guide) is ready to download for free.

On the bottom of page users can write a review. If you own a Yanmar 3GMD please write about it to help other people.

 

[ Report abuse or wrong photo | Share your Yanmar 3GMD photo ]

Video review

Yanmar 3gm marine diesel engine shown running.

 

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

No opinions have been provided. Be the first and add a new opinion/review.

 

Documents

doc0

Yanmar Marine Engine

Gaskets/Washers/O-rings 1 728370-92600 Gasket Set 1 128370-01331 Head Gasket 1 121000-01751 Sump Gasket 1 121575-01511 Timing Cover Gasket 1 128370-13201 Bonnet Gasket 1 128370-13201 Exhaust Elbow Gasket 6 124950-11450 Packing, Chamber 1 N/A Packing, Insulator 1 121520-01851 Fuel Lift Pump Gasket 1 121450-32021 Oil Pump Gasket 1 124085-02220 Crankshaft Seal (Flywheel End) 1 105225-02020 Brg Cap O-ring (Flywheel End) 1 121450-01801 Crankshaft Seal Bearings 1 121450-121450-121450-121450-705311-105225-24101-062054 Liner, Pistons, Rings 3 121450-121000-721000-105225-105225-728171-23100 Cylinder Head 3 105225-105225-121575-124950-27310-070001

3GM30 Marine Engine

Main Bearing Std Main Bearing (Middle) Main Bearing (Middle) Main Bearing (Flywheel End) B/E Bearing Std Piston Pin Bush Camshaft Ball Bearing Liner Assy Piston & Ring Assy Std Ring Set Std Piston Pin Circlip Con-Rod Assy Inlet Valve Exhaust Valve Valve Springs Valve Stem Seals Cotter, Valve Spring
0.25mm 121450-02310 121450-02380 121450-02370 121450-02320 105311-23380 N/A 0.25mm N/A 105225-22570 728170-22540
0.50mm N/A N/A N/A N/A N/A N/A 0.50mm N/A N/A N/A
Filters-Belt 1 128270-12540 Air Filter 1 104500-55710 Fuel Filter 1 121370-55730 Fuel Filter Bowl 1 24341-000440 F/ Filter Bowl O-ring 1 119660-35150 Oil Filter 1 25132-003000 V-Belt Fuel Injection/Oil Lines Cooling /Sea Water 1 728370-51101 Fuel Injection Pump 1 128270-42000 Sea Water Pump Assy 3 128170-51101 Plunger With Barrel 1 104211-42070 Impeller 3 128170-51300 Valve W/Seat, Delivery Valve 1 124070-42060 Water Pump Shaft 3 728170-53100 Fuel Injector 1 104211-42090 Gasket, Cover 3 124770-53000 Nozzle Assy 2 24107-062004 Shaft Bearings 1 128370-59080 Fuel Line- Feed Pump - Strainer 1 N/A Seal, Lrg 1 128370-59801 Fuel Line- Strainer - Pump 1 104211-42100 Seal, Sml 1 128370-59810 Fuel Line- Fuel Injector No128370-59820 Fuel Line- Fuel Injector No2 Cooling Hoses, Thermostat, Anodes 1 128370-59830 Fuel Line- Fuel Injector No105582-49200 Thermostat 1 121256-52020 Fuel Lift Pump 1 104211-49160 Thermostat Gasket Electrical Components 1 128370-49020 Hose, Pump - Bypath 1 104271-67550 Engine Stop Cable 1 128370-49020 Hose, Themostat-Mixing 1 128170-77010 Starter Motor 1 128270-49050 Hose,Bypath-Thermostat 1 124070-91250 Ignition Switch 2 27210-200300 Anode, Cylinder Block 1 124070-91290 Ignition Key 1 27210-200300 Anode, Cylinder Head

doc1

Thank you for purchasing the YANMAR Diesel Engine This manual describes the various engine parts and prescribes simple checks for normal engine maintenance. Before starting up your new engine, we recommend that you throughly read this manual to insure proper handling and use. If any sections are unclear or if you have any problems, please consult your nearest dealer or sales outlet. In view of our continuing efforts to improve quality and performance, engine parts may sometimes be changed. This may result in some discrepancies in the contents of this manual. This manual is concerned with the 2 cylinder model. Although the 1GM, 3GMD and 3HM seem to be different on the outside, their handling is the same.

Caution

This safety alert symbol indicates important safety messages in this manual. When you see this symbol, be alert to the possibility of personal injury and carefully read the message that follows.

Important

This stop symbol indicates important proper operation messages in this manual. When you see this symbol, carefully read the message that follows.
In order to deliver correct parts to you, we need accurate data on the engine you purchased. The information needed is described in the illustrations below. For ready reference, please record the information in the spaces provided under the illustrations.

I. Name of parts

1 Reduction and reversing gear 2 Output shaft coupling 3 Clutch control lever 4 Installation foot 5 Engine tube oil dipstick 6 Clutch tube oil dipstick/Supply port 7 Cooling water pump 8 Fuel feed pump 9 Exhaust manifold 10 Mixing elbow 11 Air intake silencer 12 Alternator 13 Lube oil filter 14 Starter motor 15 Decompression lever 16 Anticorrosion zinc 17 Fuel injection pump 18 Fuel injection valve 19 Crankshaft V-pulley 20 Speed control lever 21 Cooling water drain cock (Cylinder block/Exhaust manifold) 22 Fuel filter 23 Breather pipe 24 Fuel injection limiter 25 Engine lift plate 26 Lube oil supply port 27 Oil pressure sender 28 Engine stop device

III. Engine installation

[3-1.1 Inspection after unpacking During unpacking be careful not to break the engine base. Check the following points: 1) Have any nuts or bolts become loose or fallen off? 2) Have any parts become rusty? 3) Is there any water inside the engine? 4) Has any part of the engine been broken, chipped, or crushed? 5) Are any of the accessory parts/ items broken or defective?
[3-2.1 Preparation of the engine foundation plate
The installation angle will differ with the vessel configuration and installation location of the engine. The most suitable installation angle is 8 degrees and the maximum installation angle is 15 degrees. If it is greater than this, horsepower loss will increase and vessel speed will drop. In addition, abnormal wear of parts will occur and engine performance will be adversely affected.
[3-3.1 Engine installation
1) For the engine installation, be sure to use the flexible rubber mount. Yanmar prepared the flexible mounts which match the respective engine characteristics as a standard accessory.
1. Lock Nut 2. Jack Nut 3. Rubber Mount 4. Indication No. (50, 70, 75, 100)
Avoid splashing the flexible mount with water, oil etc.
Indication # Engine model 1GM 2GM 3GMD 3HM Front Rear 75 100
Installation distance (unit: mm) A B 370 400
It is convenient for installation to make the GUIDE PLATE as illustrated. 2) Be sure the propeller shaft lines up with and matches both shaft joints. If necessary adjust the height of the engine with a jack nut to line up the propeller shaft and the engine. Fit the propeller shaft and the intermediate shaft if there is one-to the engine. With a gap gauge, measure the gap of the connection at the top, bottom, right, and left. The maximum tolerance should be less than 0.2mm. Lock nut should be as low as possible. 3) Tighten the installation bolts firmly and evenly. Do not force the bolts in if the propeller shaft does not line up. Important After 50 hours operation, check that the propeller shaft lines up again, and readjust if necessary. View From Top

1 - Rear

2 - Front

1. Gap gauges

[3-4.1 Propeller, propeller shaft
1) Select a propeller which is suitable for the size and shape of the vessel, as well as for its intended usage. An extremely small or large propeller will reduce the speed of the vessel and overload the engine, which may lead to engine break down. It is recommended that a propeller be selected in consultation with a reputable dealer. However, the best way to make sure the propeller fits the vessel is to conduct a test run after installation. 2) It is effective to use a proper flexible stern tube to reduce vibration.
[3-5.1 Cooling water supply device
1) The engine should be operated only after checking the cooling water piping is completed.
If the Cooling water pump is operated without water, the rubber impeller inside the pump will be broken. 2) Kingston cock installation. Install the canvas on the outside of the hull, and the canvas or rubber packing on the inside of the hull; tighten the kingston cock. Installation directions are given in the figure at the right. Install the kingston cock cover as shown. 3) Piping For the cooling water pipe, use a rubber hose with an inside diameter of 13mm. Piping should be kept as straight and short as possible. If the pipe is too long, it will be difficult to draw water up. 4) Connect the rubber hoses to the kingston cock, cooling water pump inlet, and engine cooling water outlet, and secure with hose clamps.

Piping Diagram

1. Inside Packing 2. Kingston cock cover 3. Outside Packing 4. Direction of vessel movement
5) Seawater strainer The seawater pump will be damaged if foreign matter is allowed to get into it. Therefore, attach a seawater strainer between the seawater pump inlet and the seawater cock when the sea water cock is not already equipped with a strainer. 6) Exhaust pipe layout Be sure to use the water-lock. Installation of piping should be done as shown in the following diagram. 6-a) In case the water outlet of the engine side (A) is above water line. 6-b) In case the water outlet of the engine side (A) is below water line. 7) Air ventilation and Intake pipe If the engine is operated at below normal output, incomplete combustion can occur as a result of an overheated engine room. Therefore, the engine room should be adequately ventilated.
During piping works be sure to cover the intake opening to prevent the entry of foreign matter.
1. Seawater pump 2. Seawater strainer 3. Kingston cock
1. W.L. 2. Waterlock 3. Above seawater line
1. W.L. 2. Waterlock 3. Vacuum valve

I3-6.] Remote control

1) Control cable Use only the single lever remote control device with 1GM 2GM, 3GM and 3HM engines.
The dual lever remote control device cannot be used. Recommended Cable Speed Control Clutch Control Engine Stop (option) Control Cable Morse 33-C Morse 33-C Yanmar made Morse Cable Clamp Yanmar Standard Yanmar Standard Connecting metal fittings Yanmar Standard Yanmar Standard

Since the cable stroke may be insufficient, two holes are drilled in the shift lever. When the cable is attached to the hole 60mm from the center of the rotation of the shift lever, the strokes from the center to the forward and reverse sides must be 35mm. When the cable is attached to the hole 52mm from the rotation of the shift lever, these strokes must be 30mm. 4) Engine stop remote control Connect the engine stop remote control cable as in the illustration, after completing the wiring check that the engine stop lever can be moved smoothly through the whole stroke.
1. Clamp 2. Engine Stop lever 3. Engine stop remote control cable
[3-7.] Recommended battery capacity Use sufficient capacity of battery. 1GM, 2GM, 3GMD 3HM 12V - 70AH (Mini) 12V - 100AH (Mini)

IV. After launching

1) Check for water or air intake around the gland part of the stern tube and the kingston cock fitting. 2) Make sure that the engine installation bolts and shaft joints are firmly secured. 3) Release compression with the decompression lever and slowly run the engine with the engine starting handle. Relative compression can be determined by comparing the weight (resistance when turning) of the clutch handle when placed in the neutral, ahead, and astern positions. When there is little weight difference among the three positions, decompression is complete. If the clutch is heavier when engaged than when disengaged, this indicates that the shaft is not in the correct position. If the engine is operated under this condition, a broken propeller shaft may result. Check the alignment of the propeller shaft and the engine.
V. Fuel and lubricating oil
[5-1.] Selection and handling of fuel oil
1) Choice of fuel oil Fuel oils available in countries other than those listed above which are to equipment specification may be used. Use the chart at below to determine correct grade of fuel. United States United Kingdom Air temperature Below 5C (40F) Above 5C (40F) ASTM/D975 BS2869 No.1-D or No.2-D diesel oil Class A 1 or Class A 2
Diesel/fuel (ASTM/D975) 1-D 2-D
1-a) As further insurance of satisfactory operation, use fuel having less than 0.5% sulphur. 1-b) For maximum filter life, sediment and water should not exceed 0.1 %. 1-c) To maintain proper fuel delivery during cold weather operation, use grade No.1-D diesel fuel as defined in ASTM Designation D975 with a pour point at least 5.6C (10F) below the lowest outside air temperature. 1-d) The cetane number should be 40 minimum. Low atmospheric temperature, as well as high altitude operation, may require use of a fuel with a higher cetane number. 2) Storing fuel Proper fuel storage is vitally important. Keep all dirt, water and other contaminants out of fuel. Avoid storing fuel over long periods of time. Store fuel in a convenient place away from buildings.

Presence of water or dust in the fuel may cause failure of the engine and early wear of the fuel injection equipment. Water and dust in the fuel tank should be removed and clean fuel used. 3) After each day's operation. Fill fuel tank at the end of each day's operation. This prevents condensation in fuel tank as moist air cools.
[5-2.] Selection of lubricating oil
1) Choice of lube oil The selection of lube oil is very important to a diesel engine. If an unsuitable oil is used, or oil change is neglected, it may result in damage, and a shorter engine life. When selecting the lube oil, it must be one of the following. 2) Kinds of lube oil Choose a lube oil with a rating higher than SAE class CC. 3) Lube oil viscosity The viscosity of the lube oil greatly influences engine starting and running performance. The lube oil weight number chosen should vary with the season and temperature. 4) Recommended brands of lube oil for crankcase: SAE NO. SUPPLIER BRAND TEMP. Below 10C Shell Rotella Talona Rimula Caltex Marine Multipurpose Mobile Delvac Special Delvac 20W-40 Delvac 1100 Series Delvac 1200 Series Esso Estor HD Lube HD Standard BP Energol 10W,20(W) 10W 20(W) 10W 20(W), 10(W) 10W 20W-40 10W, 20(W) 10W, 20(W) 10W 10W 20W TEMP. 10-20C 20(W) 20 20(W) 20 20W-40 20(W) 20(W) 20 20W SAE NO. TEMP. 20-35C 30, 40 30, 40 30, 40 30,30 30, 40 30, 40 30, 40 30, 40 30, SAE NO. TEMP. Over 35C 50 50
V1. Starting the new engine for the first time

Important !

Before starting the engine for the first time check carefully the following preparations.
[6-1.] Supply of fuel oil 1) Fill fuel into the fuel tank. When you feed fuel from storage tank, put the inlet of the syphon at the middle of the storage tank. Take care not to draw unwanted materials floating on the fuel surface or depositing in the bottom. 2) Draining the fuel tank. Be sure to equip the fuel tank with a precipitation tank, as shown in the figure, and install a drain cock to remove any dirt and water that accumulate. Before starting the engine. open the drain cock to remove any precipitation and dirt.
1. Precipitation Tank 2. Drain Cock
[6-2.] Supply of lubricating oil 1) Lube oil to the crankcase 1-a) Remove the lube oil supply port (yellow cap) and supply approved lube oil.
FOR 1GM 1. Oil Supply Port
FOR 2GM, 3GMD, 3HM 1. Oil Supply Port
1-b) Check the amount of lobe oil by inserting the dipstick as far as possible. The oil level should correspond to the upper mark on the dipstick. Volume of the tube oil corresponding to the upper mark on the dipstick (with an installation angle of 8)
Engine crankcase 1GM 2GM 1.3 L 2.0 L Note.

3GMD 2.7 L

3HM 5.5 L
When running the engine for the first time, the tube oil flows to the piping thus reducing the amount of oil in the crankcase. After running the engine for several minutes, stop it for 2-3 minutes. Recheck the oil level. 2) Lube oil to the reduction and reversing gear case For the checking of the amount of tube oil to the reduction and reversing gear case, check with screwing the dipstick. Volume of tube oil corresponding to the upper mark on the dipstick (with an installation angle of 8) Important! The tube oil for reduction and reversing gear is different from engine tube oil for 3GMD and 3HM. Supply correct tube oil.

1. Dipstick 2. Empty 3. Full

1. Oil Supply Port

1. Oil Gauge Rod 2. Lower Limit 3. Upper Limit
[6-3.] Air bleeding in the fuel system See section [9.1] Fuel oil system - 2) Air bleeding in the fuel system. [6-4.] External Inspection 1) Thoroughly check for loose nuts and bolts. 2) Check the area around the revolving parts and the upper part of the engine where jigs and other tools may have been placed and forgotten. In general, be sure the engine room is always kept shipshape. [6-5.] Remote control device check 1) Pull out the engine warm up knob, change the control lever from the "speed decrease" position to the "speed increase" position. Check the slippage of the position on the bridge and in the engine room, and adjust as necessary. Note The knob for engine warm up can only be operated when the control lever is placed in the "Neutral" position. 2) Push the engine warm up knob back in, move the control lever through "Ahead", "Neutral", and "Astern", check the position of slip page in the engine room, and make adjustments as necessary. See [9.7] Remote control cable adjustment section for the adjustment procedure. 1. Control lever 2. Engine warm-up knob
[6-6.] Check of instrument panel alarm system Turn on the battery switch. Then place the key in the "ON" position and check the condition of the lamps on the panel (with the engine stopped). 1) Lube oil warning lamp. Should be lit.
A-TYPE 1. C.W. Temp 2. Charge 3. L.O. Press 4. Push Button 5. Warning buzzer 6. Key switch

B-TYPE

2) Cooling water temperature warning lamp. Should be out. (for small type panel; A-type only) For the large type panel (B-type), raise the CHECK switch "ON" to see if the cooling water temperature warning lamp lights. 3) Charging warning lamp. Should be lit. 4) The warning buzzer. Should sound. Note All the above alarm signs will continue until pushing the starting button or turning the key off.
1, Astern 2. Neutral 3. Ahead 4. Control Handle
[6-7.] Tuning To allow the lube oil to reach all parts, turn in the following sequence. 1) Place the control lever in "NEUTRAL". 2) Raise the decompression lever and leave it in the "no compression" position. 3) Open the kingston cock. 4) Turn on the battery switch, insert the key into the switch, and turn it to "ON". FOR 1GM
5) Push the starter button and simultaneously pull the "STOP" wire; turn the engine over 5-10 times and make sure there are no abnormal sounds.
FOR 2GM/3GMD/3HM Important When turning by hand, turn to the left (counter clockwise) when viewed from the front. If turned in the wrong direction, the impeller of the cooling water pump may be damaged.

1. Push Button

DIRECTION OF ROTATION
V II. Method of operation

Caution Before starting the engine reconfirm that there are no tools, etc. left in the engine area, especially areas where there are revolving parts.
3. Full Speed (7-1.) Starting 1) Electric starting

1. Neutral 2. Slow Speed

1. Warm up knob
1-a) Pull out the engine warm up knob and place the control lever in the "FULL SPEED" position. 1-b) Place the decompression handle down to the "COMPRESSION" position.

Within 15 seconds

1-c) Place the starter key in the "ON" position. 1-d) Press the starter button to start the engine.
For IGM Important (1) RELEASE the push button when engine starts. If the push button is released before engine starts, wait until starter motor and engine stop running before trying again. (2) Do not operate starter motor more than 15 seconds at a time. If engine does not start, wait at least one minute before trying again. For 2GM/3GM/3HM Note In cold weather. When starting is difficult in cold weather, raise the decompression handle to the "no compression" position and turn the starter motor over. After the engine gains momentum, return the decompression lever to the "compression" position. The amount of electricity needed will be less, and engine starting will be facilitated. 2) Emergency start 1GM, 2GM, 3GMD model can be started in an emergency by manual starting. 2-a) Pull out the engine warm up knob and place the control lever in the "FULL SPEED" position. And also place the starter key in the "ON" position in order to charge the battery after engine starts.
2-b) Raise the decompression handle to the "NO COMPRESSION" position. 2-c) Attach the starter handle with priming shaft as the angle shown in the figure and turn the starting handle hard, 5-6 times, and if the flywheel gains momentum.
2-d) Pull the decompression lever down to the compression position. Turn two or three times without stopping, and the engine will start.
2-e) After starting return control lever from "FULL SPEED" to "SLOW SPEED" [7-2.] Cautions after starting the engine. 1) Warm up the engine for more than 5 minutes. Because lube oil does not reach all the moving parts as soon as the engine is started. Operate the engine at around 850-900 rpm for at least five minutes.
Important 1) When running the engine for the first time after launching, run it for 15-20 minutes at about 1000 rpm. 2) Be sure to break-in the new engine. When the engine is new engine parts are tight. Therefore, engine life can be seriously shortened if too heavy load is placed on the engine before it is break-in Keep the following in mind during the break-in period. Do not run the engine hard for the first 5 hours after installation. Be sure to operate below 3000 rpm. With the control lever in "NEUTRAL" check the following. Be sure that water is coming out of the cooling water outlet pipe after the engine starts up. 2) Check the instrument panel warning lamp. Normal condition Key switch ON (with the engine stopped) Lube oil lamp Cooling water lamp Charge lamp Warning buzzer ON OFF ON BUZZ OFF OFF OFF OFF Abnormal condition Engine start (over 1000 rpm)

ON (Pressure down) ON (Temp. rise) ON (No-charge) BUZZ (Above trouble Except no-charge
If any of the warning lamps do not go off above 1000 rpms, they are malfunctioning. Stop the engine immediately and contact the nearest Yanmar dealer. [7-3.] Cautions during operation. The following should be checked once or twice a day. 1) Fuel Check and refill the fuel oil if needed. If air is allowed to enter the fuel injection device, it will cause the engine to stop, and also necessitate the bleeding of the fuel lines. 2) Lube oil If the warning lamp is on while the engine is running, it is an indication that there is some abnormality. First of all, check the amount. 3) Cooling water Make sure the cooling water is flowing from the outlet pipe and that the cooling temperature lamp is out. In the event water comes out intermittently, or when the amount is small, check the following.
3-a) If air is being taken into the cooling water system. 3-b) Damage of the cooling water pump. 3-c) If dirt has plugged up the cooling water pipe or the kingston cock. 4) Charge Make sure that the charge lamp is off. If the charge lamp does not go off, even when the engine rpms are raised to more than 850 charging is not taking place because of some malfunction in the charge system. Consult a dealer. 5) Temperature of parts Under full power, the surface temperature of each engine part will be about 50-60C, or slightly hot if touched with the hand. If the temperature is too high, there is some abnormality. These may include a shortage of oil or improper alignment of the propeller shaft. Consult your nearest dealer if the temperature of the engine parts is too high. 6) Exhaust smoke The emission of black exhaust smoke indicates that the engine is being overworked. If so operated, the life of the intake and exhaust valves, piston rings, cylinder liners, and fuel injection valve will be shortened. 1. C.W. Temp 2. Charge 3. L.O. Press 7) Water/oil leaks Check for any water or oil leaks, gas leakage, loose bolts, abnormal sounds, excessive generation of heat, and vibration. If there is anything wrong, consult your nearest Yanmar dealer. 8) Engine resonance A sudden, large vibration of the vessel may be caused when the vibrations (resonance) of the engine and the vibrations of the hull occur at the same time. When this happens you should either increase or decrease engine speed. 9) Clutch operation Clutch operation must be performed at a low speed of less than 900 rpm.
Important Clutch life will be significantly shortened if engaged suddenly at high speeds, or if used in a partially engaged condition. 10) Abnormal sounds during operation If abnormal sounds are detected, or the warning buzzer sounds during operation, you should promptly stop the engine and consult the nearest dealer. [7-4.] Stopping 1) Stopping procedure 1a) Place the clutch handle in the "neutral" position and idle the engine for about 5 minutes. Important If the engine is stopped suddenly while at a high temperature, the temperature of various parts will increase. This may result in engine trouble.

1-b) After five minutes' idling, place the speed control lever in the "full" position and raise the rpms to about 3600 to blow out any burnt gas in the cylinder.
1-c) Set the engine to the lowest speed (about 850-900 rpm), cut the fuel, and stop the engine.
1. Engine stops if knob is pulled 2. Engine stop cable
Important Do not stop the engine with the decompression lever. If the decompression lever used to stop the engine, fuel will spray out and accumulate on top of the pistons. This will create the danger of an explosion the next time the engine is started.
2) Be sure to close the kingston cock after stopping.
3) Drain out the cooling water. In winter and in periods of col d weather when there is the possibility that the cooling water may freeze, the cooling water should be drained out after use. 3-a) Open up the cylinder body side cock located below the intake silencer and drain out the water in the cylinder. 3-b) Open up the cock in the lower part of the exhaust manifold and drain the water from the manifold. (for 3GMD, 3HM) 3-c) Turn the crankshaft 2-3 times by starter motor to remove any water remaining in the cooling pump.
4) While the engine is still warm, wipe off any dirt and grime that has accumulated. 5) Turn off the battery switch. Note When stopping the engine with the starter switch "ON", the tube oil pressure warning buzzer will sound. This does not indicate engine trouble.
V III. Storage [8-1.] Storing Whenever the engine will not be used for several months, use the following procedure to properly store it. This minimizes corrosion and deterioration. 1) Drain fuel completely from fuel tank, otherwise moisture from the fuel system will mix with the fuel. 2) Wash the cooling system with clean tap water and drain out the cooling water from the engine completely. 2-a) Cylinder body 2-b) Exhaust manifold. 2-c) Cooling water pump Remove the cover of the cooling water pump and drain out the water inside of the cooling water pump. 3) Apply an anti-rust oil to any parts which rust easily. 4) Since the battery will automatically discharge itself if left, disconnect when fully charged, wash the exterior and store in a dry, well-aired place. Re-charge once a month during storage. 1. Cooling water pump 5) Tape to seal air inlet, exhaust pipe, and fuel tank cap. 6) Clean the engine throughly. Touch up any painted surfaces that are scratched or chipped. 7) If boat must be stored outside, cover it with waterproof material. [82.] Removing engine from storage 1) Wipe off anti-rust oil and check that the remote control system move smoothly. 2) Wiring the battery. 2-a) Rewire as shown in the wiring diagram. 2-b) Make sure wires are connected to the correct terminals.

Note Cranking for 3HM model, attach two M8 bolts at the crankshaft pulley as the figure below.
3-e) Check the fuel injection timing for all of the cylinders. Proper injection timing Degree (BTDC) 1GM 151 2GM 3GMD 181 3HM 211
For 1GM/2GM/3GMD Injection timing mark on flywheel (1T, 2T. 3T) 1. Cylinder block side timing mark 2. Flywheel
3. Crankshaft pulley 4. M8 bolt 3-f) Remove the fuel injection nozzle and check the injection spray condition. Cone-shaped condition is proper.
If the spray is not cone-shaped, check the following point.
3-f)-1. The injection pressure may be low;
3-f)-2. The fuel may be bad; Important For the disassembly, adjustment and inspection of the fuel injection pump and fuel injection valve, consult the nearest Yanmar dealer. Note It is convenient to check simultaneously the exhaust/intake value clearance when removing the starter motor.
4) Washing and replacement of the fuel filter element. Remove the lower cover of the fuel filter and wash or replace the element.
1. Fuel Filter The proper method to remove the element is shown in the figure below. When you start the new engine for the first time or after long storage, clean the filter element after 50 hours of operation. After that replace the element every 250 hours of operation. 2. Air breathing bolt 3. Filter element 4. Filter bowl 5. Tightening screws
[9-2.] Lubricating oil system 1) Engine lube oil
1. Engine oil evacuation port 1-a) Check the oil level before every operation. 1-b) Replace the oil after 50 hours of operation (for the first time, after long storage) and every 100 hours of operation. Lube oil changes can be performed most effectively while the engine is still warm. The oil will flow easily and can be thoroughly drained. The oil should be drained from the crankcase by moving the handle of the oil evacuation pump forward and backward. 2. Oil Evacuation pump (optional) 1-c) Replace the lube oil filter Replace the lube oil filter every 300 hours of operation. 1-c)-1. Unscrew canister by hand or filter replacer tool. 1-c)-2. Check that threaded adaptor is secure in headcasting. 1-c)-3. Discard used canister. 1-c)-4. Coat the top of the seal of the new canister with new lube oil. 1-c)-5. Screw new canister on to filter headcasting until canister seal just touches headcasting and then tighten by hand a further half turn.

1. Used Cannister

Important If the canister is overtightened, difficulty may be experienced in its removal and the filter may be damaged.

2. New Lub. Oil

1-c)-6. Start engine and check for leaks. Check oil level after running the engine for several minutes and fill up when necessary. 2) Reduction/reversing gear case oil. 2-a) Check the oil level before every operation.

3. New Cannister

2-b) Replace the oil. Replace the oil periodically same procedure as engine lube oil. Important Reduction/reversing gear case oil for 3GMD and 3HM is different from engine lube oil.
[9-3.] Cooling water system 1) Make sure that water is coming out of the cooling water outlet pipe during operation. 2) Inspection and replacement of anticorrosion zinc. Replace the anticorrosion zinc after every 500 hours of use to prevent electrolytic corrosion by the cooling water. Although it depends on the quality of the raw water and the operating conditions, remove the scum(dross) adhering to the surface of the anticorrosion zinc. If less than 1/2 of the anticorrosion zinc is left, it should be replaced with a new one.
Location of anticorrosion zinc Cylinder Head Cylinder Body 1GM 1
Number of Pieces 2GM 3GMD 1 2

3HM 1 2

3) Inspection and replacement of cooling water pump. 3-a) Impeller of the cooling water pump. 3-a)-1. Remove the cooling water pump cover, take out the impeller, and check for damage to the impeller and mechanical seal parts. If damaged, replace with a new one. 1. Cover 2. Packing 3. Impeller 4. Cooling Water Pump 3-a)-2. When reassembling the pump, coat the fittings of the pump shaft and impeller, both sides of the impeller, and the vane tips with grease.
Important When installing the impeller, make sure the direction of the impeller corresponds to that indicated in the figure.
3-b) Adjust the V-belt tension. Check the tension of the cooling water pump drive belt. If there is too much tension premature damage to the V-belt will occur. On the other hand of the V-belt pulley is loose it will slip and cooling water flow will be insufficient. Loosen the cooling water pump V-belt tension bolt to adjust the tension. Replace the belt if it is worn or cracked.

Adjustment Standard 5 - 7 mm (with 10 kg thumb force)
[9-4.] Inspection of engine body 1) Retightening cylinder head nuts Retighten each nut with a torque wrench before starting a new engine and after 50 hours of operation. Sequence for tightening the nuts is shown in the figure.
1. For 1GM M10 bolts are used for main 2. Sub 3. Number shows tightening order CYLINDER HEAD TIGHTENING TORQUE 1GM MAIN (M10) 7.5 kg-m 2GM, 3GMD MAIN (M12) 10 kg-m SUB (M8) 2.5 kg-m 3HM MAIN (M12) 13 kg-m SUB (M8) 3 kg-m 2) Exhaust/intake valve head clearance adjustment The clearance of the valve will affect the overall performance of the engine, so it is important that it be correctly adjusted. Check the clearance before starting a new engine, whenever assembling or disassembling and after 500 hours of operation. Adjustment shall be done while the engine is cold. 2-a) Remove the valve rocker arm cover and starter motor.
2-b) Crank the engine and set the No. 1 (flywheel side) piston to top dead center (TDC) on the compression stroke. Note Set the position at which the valve rocker arm shaft does not move even when the crankshaft is turned to the left and right, centered around the T mark. C. Maintenance standard (for all models) Intake/exhaust valves 0.20mm
1. Valve clearance adjusting screw 2. Thickness gauge 2-c) Check and adjust the intake and exhaust valve head clearances of the No. 1 cylinder. Loosen the valve clearance adjusting screw lock nut, adjust the clearance to the maintenance standard with a thickness gauge, and retighten the lock nut. In the case of 2 cylinder model, adjust the valve head clearance of the No. 2 cylinder in the same manner after turning the crankshaft 180. Note If you adust the valve head clearance of the No. 2 cylinder first, turn the crankshaft 540. Adjust the clearance of the No. 1 cylinder in the same manner. In the case of 3 cylinder model, adjust the valve head clearance of the No. 3 cylinder in the same manner after turn the crankshaft 240 and then adjust it of the No. 2 cylinder after turn the crankshaft 240 more. [9-5.] Washing the air intake silencer element Wash the element inside the air intake silencer with a neutral detergent every 250 hours of operation.

1. Speed Control bolt 2. Speed Control lever 3. Idling Speed adjusting bolt
2) Clutch control 2-a) Checking the operation lever stroke. Move the operation lever up and down (Ahead and Astern) by disconnecting the remote control cable. Check that the strokes between Neutral to Forward (A) and Neutral to Reverse (B) are nearly same. If the strokes are not the same, see your nearest Yanmer dealer.
1. Astern 2. Ahead 2-b) Checking the spring joint condition. With connecting the spring joint to the control cable, check the function of the spring of the spring joint. If the M5 thread does not move even when you shift the control handle, the cone inside of the clutch might be damaged. See your Yanmar dealer.
2-c) Tighten all nuts and bolts After inspection and maintenance, retighten all nuts and bolts securely. Caution 1) Always stop the engine when inspect and maintain the control cable. 2) Be carefully when conduct inspection and maintenance imi.-;ediately after stopping the engine. Lube oil might be high temperature in several reason.

 

Tags

NX6125 371LM EDE36150W GK-3B Coolpix 885 CDN-90 8 AA SRA-800 Schtr210 ADC5105 1500 Mkii GA-73PVM-s2 N73 Edge Function Bluechart ERB36402W Toolbox SVT-4 PRO CDP-CX355 VPL-CS7 WR250F-2005 Applications GS516T Messenger HT303SU CW-21Z413N ZWF-1200 UE32C6620UW CU-E12ckp5 PV-DV953D AW12ECB8 Power S220 RF-D1 XR-3503MK2 DVP5140 12 DCD-F100 KDL-40EX400 PCG-GRT816S DGS-1248T MAG-850 90121 MAX-A55U KDC-7080R DCR34W Connection LAM770T1 A12AHM KDL-40E4000 Stylus C67 50700W EF4124 D-BG1 Vpoint HD WAS700 R 53SV XBR716 GH22NS40 Parts XC-IS21MD HI-625ME RX3041H Vintage2-AE1 Motorola I275 SGH-M110 SHR-2160P RB-5000 Odacio DFC4 S8000 WF210ANW XAA Server Drive XXS WJ-FS616 Networks IC-M120 CDE-9846R TD-10 CQ-JA1070L D-tracker 125 CPS-7 UT163 Roadmate 760 WT300 ALL-IN-ONE Designjet 1000 Cluster 50PC1R Samsung NV7 FAX-phone B150 ZRB640W SX-217-K 755DFX 42PM3MVA PDA-5002 Urc-8060 4930G Lexmark X73 PLC-XU46 Program Printer E1245W KDC-PS9070R

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101