Reviews & Opinions
Independent and trusted. Read before buy Zanussi FCS 872C!

Zanussi FCS 872C

Manual

Download (German)
Zanussi FCS 872C, size: 972 KB
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Zanussi FCS 872CAbout Zanussi FCS 872C
Here you can find all about Zanussi FCS 872C like manual and other informations. For example: review.

Zanussi FCS 872C manual (user guide) is ready to download for free.

On the bottom of page users can write a review. If you own a Zanussi FCS 872C please write about it to help other people.

 

[ Report abuse or wrong photo | Share your Zanussi FCS 872C photo ]

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

Comments to date: 1. Page 1 of 1. Average Rating:
Matthias86 10:58pm on Thursday, April 8th, 2010 
everything not found any yet Huge capacity and the bottle shelf is excellent The handle is a bit plasticy looking

Comments posted on www.ps2netdrivers.net are solely the views and opinions of the people posting them and do not necessarily reflect the views or opinions of us.

 

Documents

doc0

SERVICE MANUAL
Compact front loaded Washing Machines (Timer controlled)
Electrolux Muggenhofer Strae 135 D-90429 Nrnberg Germany Fax +49 (0)1022 Spares Operation Ausgabe: 10.2003 DGS-TDS-N - R.Kurzke

Publ.-Nr.: 355 EN

Compact front loaded Washing Mashines from Torsvik

Timer controlled

Table of Contents
General features Programs Timer function Operation principle Types of Spin Construction Enclosure Upperframe Lowerframe Rear of machine Front panel Detergent dispenser Front hatch Hatch locking switch Washing unit with outer drum Function Monitoring of spin phase for imbalance Water supply valve Level regulator Heating element NTC-Thermistor Drainage pump Service/Accessibility Top plate Panel Hatch Hatch hinge Rear ot machine Drum unit Shockabsorbers Outer drum with drum bearing Troubleshootings Motor check Diagrams Washing programs table Timer diagram Timer connectors 31 32

10.2003 R.K.

Controls
Timer type Push button functions Knob/Command func. VD55 On/off, Rinse hold Program, Temperature

Dimensions

Height Width Depth Tub material Drum volume Washing capacity Inlet hose length Outlet hose length Det. dispenser type of Cord length 670 mm 495 mm 515 mm Carboran 27 l 3.00 kg 130 cm 160 cm Two chambers 170 cm

OPERATION PRINCIPLE

Traditional washing Operation
Detergent hatch Hose between detergent dispenser and outer drum Outer drum Inner drum 9 Heating element Rubber bottom, fixed to outer drum Drainage pump Circulation hose Drainage hose
The partides of soiling substances which are freed from the textile fibres by the chemical action of the detergent at the temperature of the washing water are re-moved by the flow of water through the fibres. The reversing rotation ofthe drum causes mechamcal interaction between the parts ofthe load and the detergent solution which separates the partides from the textlies. The water level is at such a height that the load is successively lifted from the solution by the ridges formed in the inner drum and then falls back into the solution. The Circulation ofthe solution during the rotation ofthe drum prevents the accumulation of detergent in the rubber bottom.

CONSTRUCTION Enclosure

The enclosure consists of: - a lacquered steel sheet pressing forming the front and both sides, fixed between upper and lower CARBORAN frames a removabie galvanized sheet steel back plate a top of lacquered steel sheet, fixed to the rear of the upper GARBORAhOframe. Top, lacquered steel sheet Upper frame, CARBORAN Back plate, Front and sides, lacquered steel sheet Lower frame, CARBORAN

Upper frame

1. Upper frame of CARBORAN 2. Interference suppressor 4. Spring, drum suspension 5. Level regulator, level 1 level 2, and anti-foam function
6. Level regulator, overflow protection 7. Water supply valve

Lower Frame

1. Lower frame, of CARBORANO 2. Shock absorber, fixed to frame with plastic pin 3. Electronics unit 4. Drainage pump, inserted in track and locked to lower frame with plastic snap fixing 5. Plastic protection for drainage pump 6. Drainage hose, fixed with two plastic clamps 7. Adjustable rear foot with lock nut

Rear of machine

Water supply hose Shock absorber Electronics unit 4 Motor Temperature sensor, NTC thermistor Rubber bottom with "pin trap" (filter not provided) Drainage pump Heating element, 1600 W. Pressure chamber Connection terminal block Level regulator, level and anti-foam function Level regulator, overflow protection Rear counterweight

- 10 -

Front panel
Front panel Program scale Temperature scale Knob Detergent hatch/dispenser Fixing screw, (behind detergent hatch) Lamp lens Pilot lamp Fixing screw, (Under top plate) Fixing screw for panel

Detergent dispenser

Water enters through the rear nozzle (6) and then through the water distributor to the detergent dispenser. Water is directed to the detergent dispenser section in accord-ance with the position ofthe program-controlled cam-guided finger, washing the detergent/rinsing agent it contams down into the drum.
Detergent hatch Detergent dispenser with internal water distributor Linkage arm Water distributor cam, program-controlled Programmed Controller Nozzle, water supply Link System pivot Cam-guided finger

- 11 -

Front hatch
The hatch is locked during washing by a bimetallic electric hatch lock and is opened by depressmg the hatch lock pad. When the hatch is closed and the On/Off button is pressed, a Signal lamp Illuminates after approximately 5 seconds, the hatch 1s locked electrically and the selected washing cycle Starts. When the program has been exe-cuted, the lamp extinguishes after 45-120 seconds and the hatch can be reopened. 9 External hatch frame Hatch lock pad Hatch glass Internal hatch frame Hatch hinge Electrical hatch lock Locklever Splash protection Supporting beam

Hatch locking switch

The security of the hatch is ensured by an electromagnetlc lock with function s described below. when the lock is activated, the voltage-sensing unit closes the switch which con-nects voltage to the electrical components of the machine. During operations, the slide (A) remains mechanically locked and thereby prevents opening of the hatch by fixing the hatch lock lever When the hatch lock has been deactivated, It remains locked for approximately 45-120 seconds to ensure that the drum is statlonary before the hatch is opened.

ELECTRICAL DIAGRAM

Lock lever (in hatch) Slide PTC resistor Switch activated by the PTC resistor

- 12 -

Washing unit with outer drum of CARBORAN
Ring for fixing bellows to enclosure Bellows Screw, front counterweight Front counterweight Screw, front/rear outer drum Ring for fixing bellows Front section of outer drum, CARBORAN Packing Inner drum, stamless steel Rear section of outer drum, CARBORAN Drum shaft sealing ring Inner ball bearing Outer ball beanng Rear counterweight Pulley wheel
The outer drum consists of two sections of CARBORAN fixed together with a number ofthread-cutting screws. The two counterweights are screwed to the sections.

- 13 -

Monrtoring of spin phase for imbalance
This sequence is repeated while the load remains unbalanced.
.a total of 16 times (10 minutes) or until balance is achieved. if balance is not obtained, the spin is omitted from the program.

Programmed control unit

Imbalance control, function
A check for imbalance of the load 1s performed during 15 seconds at 85 rev/min. before the spin phase. If imbalance is detected, the tachometer generator and the motor current give an irregulr Signal to the micro-processor on the electronics board which then Interrupts the spin phase. The machine then returns to 55 rev/mm. rotation and re-distributes the load to achieve balance before performing a new check at 85 rev/min. If imbalance persists, redlstribution of the load is repeated for a period of 10 minutes (16 attempts) or until balance is achleved. If no balance is obtained after 10 minutes, the program continues forward with-outspln. When balance is obtained, the program continues with spin atthe speed speci-fied.

- 14 -

Water supply valve

General characteristics

This electro-magnetic controlled valve regulates the supply of water to the machine via the water distributor in the detergent distributor. It 1s actuated by a solenold which is controlled electrically bythe programmed Controller via the level regulator. When the valve Is inactive, (without voltage) the spring holds the splndle down and the rubber cone seals a small hole at the centre of the membrane. A head of water bullds up which holds the membrane against Its seating and closes the valve. When voltage 1s applled to the solenold, the splndle with the rubber cone is drawn up-ward against the spring and the hole in the membrane 1s exposed, permitting the passage of water. The pressure differential 1s lost and water can flow freely through the valve. 9 Water entry Valve housing Filter Flow regulator Coil Spring Spindle Rubber cone Membrane 10 Water delivery

Level regulator

The level regulator momtors the level of the water in the machlne and adapts the water level to that required at different stages ofthe washing sequence selected. acts s a low-water safety device s It is connected in series with the heating ele-ment. It disconnects the voltage to the element when the water falls below a certaln level. acts s an anti-foam protection by sending a Signal to the electromcs which Interrupts the spln phase and restarts this when the foam has subsided. (VE 60 and V 60 program med Controllers).

- 15 -

Heating Element
The element for heating the water is of the encapsulated type, i.e. the spiral resistor is hermetically sealed in a stainless steel enclosure. Power Resistance 1600 W 230 V 240 V 31.2 - 34.3 Ohm 33.9 - 37.4 Ohm
Element Rubber packing Fixed f lange Electrical connection pin Locking nut Adjustable f lange Fuse
The seal between the element and the outer drum is obtained with a rubber packing which expands when the locking nut is tightened.
NTC-Thermistor (Temperature control)
Temperature control by means of NTC thermistors is incorporated in models controlled by Programmed control units VA 60, VB 60 and VE 60.

NTC temperature sensors

Plastic housing Metal capsule NTC resistance Electrical contacts
Table with resistance at different temperatures (3%) Temperature C 85 Resistance kOhm 17.3 11.5 7.84 5.46 3.90 2.97 2.32
The temperature of the washing water is controlled by the microprocessor via an NTC sensor. The internal resistance ofthe sensor decreases s the temperature increases. This decrease is registered by the microprocessor which disconnects the heating element when the required temperature has been reached. With a short-circult or other failure in the NTC thermistor, the control unit cancels the heating stage and completes the program without heating. 10.2003 R.K.

- 16 -

Drainage pump
Impeller Rotor Stator Pump housing 0-ring
The rotor consists of a permanent magnet which can rotate clockwise or anti clock-wise. The rotor can rotate one quarter revolution without movement ofthe impeller. Ifthe impeller seizes, the rotor can therefore make small movements in both directions until the impeller is freed. An unusual sound may be heard at Start which is quite normal. Function check Check that the impeller can move freely. Check the resistance of the Stator winding. This should be 170 Ohm. Max. capacity Power consumptlon = 20 l/mm. = 30 W

- 17 -

SERVICE/ACCESSIBILITY

Top plate

Remove the 4 screws (A) at the rear edge of the plate. Draw the top plate backward

Accessibility:

A B Supply valve Level regulator, level and anti-foam C Level regulator, overflow protection D Capacitor/ Interference suppressor

- 18 -

Remove the top plate Remove the 2 screws (9). Remove the knob (4). Unlock the holding catch by msertmg a fine screwdriver (or equivalent) straight through the hole, rotating the knob anti clockwise at the same time until the knob can be removed. Remove the temperature scale (3) by llfting the lock on the plastlc shaft and with-drawing the scale. Remove the program scale after removmg the nut. Remove the screw behlnd the program scale. Remove the detergent hatch (5) by jerking iIt past a stop. Remove the screw (6) inside the hatch. Remove the screw (10) to free the detergent dispenser and llft the panel away from the front edge of the detergent hatch.
A B C Programmed control unit Press-operated switch Potentiometer, temperature setting (Not provided on all modeis)

- 19 -

Removal:
Remove the two screws (A) holding the hatch to Its hinge. The outer hatch frame is snapped over the outer edge ofthe inner hatch frame. Carefully lever the frames apart and remove the outer frame. The opening pad with springs, fixed to the inner frame with 2 screws Is now accessible. The hatch glass Is fixed in the inner frame with 4 plastic projections. Bend these open to permit removal ofthe glass.

Re-assembly:

Place the glass agalnst the inner hatch frame. Check that the 2 projections (B) on the edge of the glass are in llne with the corresponding spaces In the Inner frame and press Into positlon past the plastic projections. Place the outer hatch frame agalnst the inner frame and press together.
Hatch lock fixed to the Inner hatch

- 20 -

Hatch hinge
Remove the hatch from the hinge. (Screws A) Remove the locking ring around the outer part of the bellows and remove the bellows. Press the bellows Inward toward the drum to permit passage ofthe hinge. Remove the two screws (B) fixing the hinge. Note the locking nuts on the inside. To simplify Installation of a new hinge, the Internal beam supporting the hinge Is also to be be removed. Lean the machlne backward and remove the screw (C) fixing the beam to the bottom edge of the front (under the machlne). Then remove both hinge and beam.
7 To Install a new hinge, It Is simplest to fix the hinge first agalnst the supporting beam by means of a pop-rivet through the upper triangulr hole In the hinge and the hole in the correspondmg place In the beam (D). If no such hole Is avallable, mark the beam through the triangulr hole and drill a hole f3.5 mm. Mountthe pop-rivet with its head toward the hinge. Note that the plastlc splash protection Is to be located between the hinge and the supporting beam when mounting the pop-rivet. 8 Then insert the hinge with supporting beam through the hatch opening. Fix with screws and locking nuts. Refitthe beam in position against the bottom edge of the front. Hinge Pop-rivet 0 3,2 mm

Supporting. beam Plastic splash protection

- 21 -

Remove the 4 screws fixing the back plate to the top plate (1). Remove the 11 screws around the edges of the back plate (2). Remove the back plate.
A Belt and pulley The pulley is fixed to the drum axie with a 5 mm hex.socket head screw. Electronic circuit board for speed control of motor Disconnect the electrical contacts and press the plastic snap fixing (under the machine ) to the side and then lift out the electronics unit. Motor This is fixed with 4 hex. socket head screws to the outer drum. Use an 8 mm Allen key to remove these screws. Removal of heating element Disconnect the electrical contacts. Remove the nut at the middle of the element (that which expanded the pack-ing). Then press the threaded section inward. Withdraw the element from the outer drum. Temperature sensor, NTC thermistor Disconnect the electrical contacts. Carefully lever, using a screwdriver, the rubber bushing from the outer drum. Remove the NTC thermistor from the rubber bushing. Removal of drainage pump Slacken the hose clamps and remove the hoses from the pump. Disconnect the electrical contacts and remove the plastic protection over the pump. Push down the plastic projection (H) and withdraw the pump backward. Rubber bottom, (pin trap) Slacken the clamps holding the hoses fixed to the rubber bottom. Rear counterweight Remove the belt and pulley. Remove the 3 screws fixing the counterweight to the outer drum. Lift the counterweight away from the expander bolt fixmgs. Pressure chamber Remove the hose clamp at the rubber bottom. Remove the screw (8 mm socket) holding the pressure chamber to the outer drum. Draw the Container backward and remove the hoses to the pressure (water level) switch.

- 22 -

Drurn unit
(to be lifted out when replaeing inner drum, bearing or front counterweight). Remove top plate and rear plate. Remove the clamping ring around the hatch opening and then separate the bellows from the front. Disconnect all of the electrical contacts from the drum unit (heating element, motor and temperature sensor). Disconnect the drainage hose and the drainage pump from the rubber bottom (see page 33). Disconnect the hoses between the detergent dispenser and the outer drum (at the drum). Disconnect the air hoses at the level regulators. The rear counterweight and the motor can be removed from the drum unit to simplify the lifting of the drum unit out of the enclosure. Remove the pressure chamber and the electronics unit to obtain access to the shock absorbers. Disconnect the shock absorbers from the drum unit by removing the pin at the upper fixing.

10 Lay the machine on the floor, front downwards, making suitable arrangements to protect knobs, buttons etc. against damage. 11 Disconnect the suspension springs from the upper part. This can be simplified by placing a wire loop under the end of the spring and pulling on the loop with a "handle" - a screwdriver or similar. 12 Grip the pulley and lift the drum unit, (with back so straight as possible), off the chassis. lt is recommended that two persons perform this operation.

Shock absorbers

The shock absorbers are installed between the lower frame and the drum unit and are held in positlon in the fixmgs with pms.
Removal of shock absorbers:
Depress the lockmg catch by pushmg a pipe socket (A) over the end ofthe pin and the catch, (internal diameter of socket (0 = 14 mm.). Withdraw the pin from its fixmg with pliers. The shock absorber can be removed when the upper and lower pins are removed.

Replacement:

As the original pms may be damaged during withdrawal, new pms should be used. Lubricate the pm with some type of alcohol. The lubricant must evaporate after insertion of the pins and grease may not be used. Rotate and fully insert the pm from elther slde. Check that the locking catches project and lock the pins correctiy.

- 23 -

Outer drum with drum bearing
The outer drum consists of two sections of CARBORAN with a sealing ring between, fixed together with a number of thread-cutting screws (A). When installing the sealing ring, the splice, marked with red, is to be located upward so that the red marking is visible at the recess on the upper sides of the drum sections.

Front outer drum

lnner drum

Rear outer drum

The bearing which carries the drum axle is installed inside a cylindrical steel support embedded in the rear section D Outer rear drum section E F Rear ball bearing (mm. type 6203-2Z). Front ball bearing (mm. type 6205-2Z).
G Drum axle seal H Earth connection pin.

- 24 -

- 25 -

- 26 -

- 27 -

- 28 -

- 29 -
Programmes tables legend * P In models with one-level pressure switch, all water fills are performed at the same level 1st level water fill time

RA TO

Minutes Seconds Rapid advance Spin max. time (timeout) 355

- 30 -

- 31 -

- 32 -

 

Tags

Motorola 8700 37LB2R 81302 V140I Vi 1355 RC435 Civil 2010 FTR9952 12S EK5361X-premier- HD4QE22SC TA-1140 42HP25BAT NW-E505 YM-2000 Malibu 2004 ALL-IN-one PC CS 20 BMW 120I Aspire 2920 TH-42PX20 D300 DUO CLP-315 DCR-DVD150E GC-339ngls ICD-P30 DT-42PY10X PCG-SR11K Fur DAY Hobbymatic 803 Harmony 880 TX-480 200 EXC Gstream ZWF1000 Review R-770B Plantronics CT10 Gear Acid STR-DE425 JR Cartridge KRC-V679R DCR-DVD305E A2150HCT HF8400 Kxtg6411PD DVD-3800 Htz151dvd IC-T7A Lounge Ur3 TTP PSR-OR700 Anti-virus 2011 Keycase DEH-P7450MP S3370 FX-2180 KLV-40S400A Mixer HVR-M25AN VL430 P3600 UX-107A MB-D200 Minolta 7145 VGN-AR11B G700C LE32A450c2 Doro 540R DC-223 DH400P DPU-3K6 NN-K627M RX1202FX PSR-640 Station T4X System Abit BF6 HDR-XR200E Tool LT EVO N200 ME-20B XM2540 AFC90680X 6P MP FK-103 X5690 RT-21FB75V DVD-2930CI Hypermag Mach 2 A2 1U CD1402B 53 WS-WV10C K5400 CP-X5021N KW-AVX730 EH1930 SX-780 FX180P Plus UF-550

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101