Contents

For the User
Important Safety Information Your New Washing Machine Description of the Appliance
Door locked light Detergent dispenser drawer Child safety feature 6-9-12-15 16-16 16-17 17
Something Not Working Guarantee Conditions

18-19 20

For the Installer
Installation Instructions Technical Specifications
Unpacking Positioning Water inlet Water drainage Levelling Special conditions In the interest of the environment Electrical connection 23 23-25

The Control Panel

Turning the acoustic signal off

Operating sequence

Load the laundry Measure out the detergent Measure out the fabric softener Switch the machine on Select the required programme/fabric Select the temperature Select the spin speed or the RINSE HOLD option Select the desired options Start the programme How to change a programme during its cycle How to cancel a programme during its cycle How to open the door during the cycle of a programme End of programme

Washing Hints

Which detergent?. And in which form?
Wash Care Symbols Washing Programmes Maintenance and Cleaning
Descaling After each wash Maintenance Wash External cleaning Cleaning the dispenser drawer Cleaning the drawer recess Cleaning the filter The dangers of freezing
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions Hints and tips Environmental information

Your New Washing Machine

Your new washing machine, fitted with the Zanussi JET SYSTEM, meets all modern requirements for effective treatment of laundry with low water, energy and detergent consumption. Even small loads are washed economically because the amount of water used is regulated automatically according to the load and type of fabric.
Automatic cooling of the wash water to 60C before draining, with the 90C programme. This reduces thermal shock to fabrics, helping to prevent creasing. The special wool programme with its new delicate wash system treats your woollens with extreme care. The anti-unbalance device ensures that the washing machine remains stable when spinning.
In the interest of the environment

Ecological hints

To save water and energy and help protect the environment, we recommend that you follow these hints: Normally soiled laundry may be washed without prewashing in order to save detergent, water and time (the environment is protected too!). The machine works more economically if it is fully loaded. With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed at a lower temperature. Measure out detergent according to the water hardness, the degree of soiling and the quantity of laundry being washed.

6 OPTIONS button

Press this button to select the following options: PREWASH: select this option if you wish your laundry to be prewashed before the main wash (not available for wool). The prewash ends with a short spin at 650 rpm in programmes for cotton and synthetic fabrics, whereas in the programme for delicate fabrics the water is only drained. AA 40: this option can be selected for cottons and synthetics lightly or normally soiled with a temperature of 40C and higher. If you select 40C , the machine will prolong the time at 40C in the washing phase, this will allow an A class in energy efficiency and washing performance to be achieved. If you select 90C and press the AA 40 button, the washing temperature will be reduced from 90C to 60C. If you select 60C or 50C and press the AA 40 button, the washing temperature will be reduced to 40C. In both cases the washing time will be prolonged. QUICK: select this option for laundry that is only slightly soiled. The washing time will be reduced according to the type of fabric and the selected temperature. The PREWASH, the QUICK and AA 40options cannot be selected together. Important! The first time you use the washing machine, when you switch it on, it may give an audible warning signal. This is due to the fact that the washing machine has performed a washing cycle during the manufacturers inspection tests, and this cycle has not been erased after its completion.

7 START/PAUSE button

This button has three functions: Start: after you have selected the desired programme and options, press this button to start the washing machine. The light above the button will stop flashing and remain lit. Pause: when you press this button again, the programme in progress is interrupted. The light above the button will start flashing. To restart the programme, press the button again. When you PAUSE the cycle, the DOOR LOCKED light goes out, and it becomes possible to open the door, provided the washing machine is not in the heating phase beyond 55C; the level of the water is not high; the drum is not turning. Important! You must set the washing machine to PAUSE before you make any change in the programme in progress. Draining of water and spinning after the execution of programmes with the RINSE HOLD option.

8 SKIP/RESET button

This button performs two functions: - Clears the memory - Selects special programmes At the end of every programme the SKIP/RESET button must be pressed once or repeatedly to clear the programme memory. All the lights must be off. If the previous programme is not cleared, an audible signal will sound, when you switch the machine on.

Do NOT overload the machine. Weigh the laundry the first few times you use the appliance. The average weights of the most common items are listed below as a guide: 1000g = 1 kg Sheet Pillow case Tablecloth Serviette Tea towel Linen hand towel Towelling hand towel Towelling bath towel Bath robe Mans shirt Apron 700-1000 g 100-200 g 400-500 g 50-100 g 70-120 g 100-150 g 150-250 g 700-1000 g 1000-1500 g 200-300 g 150-200 g
quantities. Bleach is very corrosive; it should be used with care and kept out of reach of children. Some stains such as fruit, wine, grass, rust etc. are difficult to remove and should be treated before washing with specific products, which can be found in most household shops. In some cases it may help to soak the stain before washing with a special presoak product or biological detergent. Only wool marked Pure New Wool - washable, preshrunk can be washed in the machine using the wool programme; other types of wool should be washed by hand or dry cleaned. If you have used the machine to wash, rinse or spin only non-colour fast garments, there may be dye left in the sump. To ensure any subsequent wash is not contaminated with the dye, select and carry out a rinse and spin programme, without any garments, to ensure that any dye is removed from the sump. Once you have finished using the machine, you are advised to unplug it and turn off the water tap.
Load the laundry loosely alternating large items with small ones. Sort the laundry according to the type of fabric, colour-fastness and how dirty it is. Avoid washing unhemmed or torn items as they may unravel. Before washing, empty all pockets of small objects which may have been left inside (coins, keys, screws etc). as these could damage the drain pump. When washing curtains, remove the hooks. Close poppers and zips and fasten loose buttons. It is essential to wash new coloured items separately when washing for the first time. When washing fabrics requiring different wash temperatures together, always select the lowest temperature. White items should not be washed with coloured items. Very small items (handkerchiefs, ribbons, socks etc) should be washed in a washing bag or a pillow case. Use a good quality detergent suitable for automatic washing machines. Use the correct quantities of detergent. For wool, use gentle detergent only in small

JETSYSTEM wash

As the Jetsystem is flexible and adjusts water intake according to wash load size it is not possible to give you exact recommandations as to the amount of detergent that should be used for any one wash. Therefore we recommend that you use approximately 1/3 less than the detergent manufacturer recommends on the packet or bottle, making the appropriate allowances for soft or hard water, and light or heavy soilage of clothes. If you have judged the amount correctly you should expect to see a soft sudsy liquid during the wash. It is not necessary to have a head of lather on the water.

Which detergent?.

To ensure you obtain the best wash results from your appliance, it is important to use the right detergent in your everyday wash, and only detergents recommended for use in automatic machines. To maintain the appearance of your clothes and household textiles and to make them last longer you should use different types of detergent for different washes, whether for whites, colours or delicates.

And in which form?

Not only are there different types of detergent, but they are also available in different forms. Whether you chose a powder or liquid in traditional or compact form is your own personal choice.

TRADITIONAL POWDERS

Pour the powder directly into the dispenser drawer. Do not sprinkle powder onto clothes in the machine drum.

WHITES

We recommend the Ariel product range which is biological and designed to provide excellent cleaning and stain removal even at low temperatures.

TRADITIONAL LIQUIDS

Liquid can be placed in the main wash compartment of the detergent drawer marked with the symbol , start the machine immediately upon placing the detergent in the dispenser drawer. Alternatively the detergent is measured into the specially designed dosing device* which should be placed on top of the laundry, and at the back of the machine drum.

NON BIOLOGICAL

If you prefer to use a non biological detergent, which does not contain enzymes we recommend Fairy. Fairy provides good cleaning and stain removal.
COMPACT POWDERS AND LIQUIDS
Compact detergents (or concentrates as they are also known) are available in liquid or powder form, and generally require a smaller dosage. Follow the manufacturers instructions to ensure the most economical usage. Pour the detergent directly into the dispenser drawer, or alternatively measure the detergent into the specially designed dosing device* which should be placed on top of the laundry, and at the back of the machine drum. * If you use a dosing device in a washer dryer, please ensure the dosing device/ball is removed before carrying out a drying programme.

COLOUREDS

For coloured items you should use a detergent which is designed to clean while maintaining the original colour. Ariel Color does not contain bleach and therefore helps to preserve colours.

DELICATE ITEMS

When washing delicates such as woollens, you should use a product which is specially designed to care for fine fabrics. Dreft Automatic is suitable for woollens and other delicates.

FABRIC CONDITIONERS

These are ideal for improving softness, and also reduce static cling on synthetics and make ironing easier. They are available in two types: For example Lenor liquid fabric softener, for use in the washing machine/washer dryer. The liquid fabric softener should be poured into the compartment marked with the symbol. Follow the manufacturers dosage instructions and never exceed the MAX level. Bounce conditioning sheets for use in a tumble dryer. We recommend the conditioning sheets are pinned (using a safety pin) to an article of laundry and placed in the tumble dryer. 13

LAUNDRY BLEACH

For additional stain removal you may wish to use a product such as Ace Gentle Bleach which is used in addition to your chosen detergent. Ace is suitable for all washable fabrics including silks, woollens and coloureds.

Wash Care Symbols

Wash care labels inside garments recommend how to launder your clothes with the best results. The care labelling code is in line with care labelling used in the rest of Europe. The symbols used make it easy to select the correct programme on your washing machine.

WASHING SYMBOL

WASH ACTION
Normal (Maximum) Normal (Maximum)

FABRIC

White Cotton or Linen without Special Finishes Cotton, Linen or Viscose without Special Finishes Colourfast at 60C. Nylon, Polyester/Cotton, Viscose with Special Finishes, Cotton/Acrylic Mix. Cotton, Linen or Viscose Colourfast at 40C but not 60C. Acrylics, Acetate, Triacetate, Wool mixes, Polyester/wool blends. Wool, wool mixtures, Silks Do not machine wash
Reduced (Medium) Normal (Maximum) Reduced (Medium) Much Reduced (Minimum) Hand wash only
BLEACHING Chlorine bleach may be used IRONING Hot iron Warm iron Cool iron DRY CLEANING May be dry cleaned. Other letters and/or a bar beneath the circle will indicate the required process to the dry cleaner. TUMBLE DRYING with high heat setting with low heat setting May be tumble dried Cotton, Linen, Viscose Polyester mixtures, Wool Acrylic, Nylon, Polyester

A cross through any symbol means DO NOT fabric conditioner to avoid the conditioner entering the machine prematurely. When using liquid detergent and a prewash programme, place the detergent into the correct compartment in the dispenser drawer, after the prewash has finished. 14

Important Notes

For best results, always use the dispenser drawer for dispensing detergents and liquid additives. Once the dispenser has been filled, close it by pushing it in gently. This is particularly important if you are using

Washing programmes

Type of laundry and symbols on labels
Programme/ temperature Cottons 60-90C
Description of programme Main wash at 60-90C 3 rinses Long spin
Consumption* Available options Energy kWh 1.9 Water litres 47 Time h/min. 2.28
White cotton: e.g. sheets, tablecloths, household linen
SPIN SPEED RINSE HOLD PREWASH AA40 QUICK SPIN SPEED RINSE HOLD PREWASH AA40 QUICK
Coloured cotton: e.g. shirts, blouses, underwear, towels, household linen

Cottons 60-50-4030C

Main wash at 60-50-4030C 3 rinses Long spin

2.5 kg

Synthetic fabrics and blends: e.g. shirts, blouses, underwear

Synthetics 60-50-4030C

Main wash at 60-50-4030C 3 rinses Short spin Main wash at 40-30C 3 rinses Short spin
SPIN SPEED RINSE HOLD PREWASH AA40 QUICK SPIN SPEED*** RINSE HOLD PREWASH QUICK
Delicate fabrics: e.g. acrylic fabrics, viscose, polyester, synthetic blends

Delicates 40-30C

Wool 40-30C
Main wash at 40-30C 3 rinses Short spin

SPIN SPEED RINSE HOLD

The coloured cotton programme at 60C with a wash load of 5 kg is the reference programme for the data entered in the energy label, in compliance with EEC 92/75 standards. * This data is given purely as an indication: the consumption values may vary in relation to the quantity and type of laundry, the temperature of the water supply and the ambient temperature. The data refers to the highest temperature provided for each programme. *** Only for models FJ1054W and FJ1254W

Maintenance and Cleaning

Before any maintenance or cleaning is carried out you must DISCONNECT the appliance from the electricity supply. To aid cleaning, the top part of the additive compartment should be removed.

Descaling

The water we use normally contains lime. It is a good idea to periodically use a water softening powder in the machine. Do this separately from any laundry washing, and according to the softening powder manufacturer's instructions. This will help to prevent the formation of lime deposits.

After each wash

Leave the door open for a while. This helps to prevent mould and stagnant smells forming inside the appliance. Keeping the door open after a wash will also help to preserve the door seal.

C0068 P1086

Maintenance Wash
With the use of low temperature washes it is possible to get a build up of residues inside the drum. We recommend that a maintenance wash be performed on a regular basis. To run a maintenance wash: The drum should be empty of laundry. Select the hottest cotton wash programme. Use a normal measure of detergent, must be a powder (such as Ariel Futur).
Cleaning the drawer recess
Having removed the drawer, use a small brush to clean the recess, ensuring that all washing powder residue is removed from the upper and lower part of the recess. Replace the drawer and run the rinse programme without any clothes in the drum.

External cleaning

Clean the exterior cabinet of the appliance with soap and water only, and then dry thoroughly.
Cleaning the filter Cleaning the dispenser drawer
The washing powder and additive dispenser drawer should be cleaned regularly. Remove the drawer by pressing the catch downwards and by pulling it out. Flush it out under a tap, to remove any traces of accumulated powder.

The water drain filter

A clean filter is important for the correct operating of the machine, and should therefore be cleaned after every washing programme. Open the filter door and place a container underneath to catch any spillage.

4:19 PM

If the filter is blocked and the machine is unable to drain you will need to drain the water manually from the machine at this stage. To do this, unhook the drain hose from the standpipe or sink and hold the end of the hose over a bowl on the floor. The water should drain by gravity into the bowl. When the bowl is full, hook the hose back up and empty the bowl. Repeat the procedure until water stops flowing out. Unscrew and remove the filter.
Clean the filter using a hard bristle brush. Tighten up the inlet hose.

The dangers of freezing

If the machine is exposed to temperatures below 0C, certain precautions should be taken. Turn off the water tap. Unscrew the inlet hose. Unhook the drain hose from the rear support and position the end of this hose and that of the inlet hoses in a bowl. Run the draining programme. To do this: Switch the machine on Select a washing programme Press the SKIP/RESET button three times Press START/PAUSE button Disconnect the appliance. Screw the inlet hose and reposition the drain hose. When you intend to start the machine up again, make sure that the room temperature is above 0C.
Clean carefully under a fast running tap.

Warning

When the appliance is in use and depending on the programme selected there can be hot water in the filter. Never remove the filter during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When replacing the filter, ensure it is securely retightened so as to stop leaks and young children being able to remove it.

The water inlet filter

If your water is very hard or contains traces of lime deposit, the water inlet filter may become clogged. It is therefore a good idea to clean it from time to time. Turn off the water tap. Unscrew the water inlet hose.

Something Not Working

Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Force Centre, please carry out the checks listed below. IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. During machine operation it is possible that, the light of the START/PAUSE button and one of the following lights start to flash: : problem with the water supply : problem with water draining : door open Once the problem has been eliminated, press the START/PAUSE button to restart the programme. If after all checks, the problem persists, contact your local Service Force Centre.

Symptom

The machine does not start

Possible causes

The door has not been closed. The plug is not properly inserted in the power socket. There is no supply at the socket. The main fuse or the fuse in the plug has blown. The START/PAUSE button has not been depressed. The water tap is closed. The filter in the inlet hose is blocked. The inlet hose may be squashed or kinked. The door has not been closed. The end of the drain hose is too low. The end of the drain hose is submerged in water. There is no vent in the end of the drain hose. The drain hose may be squashed or kinked. The RINSE HOLD option has been selected. The drain filter may be blocked. The drain hose extension, if fitted, is not correct. Follow the instructions for connecting to the waste. The drainage system pipes are blocked. The wash load is unbalanced: redistribute the clothes inside the drum to allow the machine to spin. Too much detergent or unsuitable detergent has been used (creates too much foam). Check whether there are any leaks from the inlet hose fittings. It is not always easy to see this as the water runs down the hose; check to see if it is damp. The drain hose may be damaged or not securely positioned. The detergent dispenser drawer or recess is clogged. The drainage system pipes are blocked. Too little detergent or unsuitable detergent has been used. An insufficient amount of detergent leaves the laundry looking grey and causes lime scale to form. Stubborn stains have not been treated prior to washing The correct wash programme/temperature has not been selected. Too much laundry has been placed in the drum.

The machine does not fill
The machine fills then empties immediately The machine does not empty and/or does not spin
There is water on the floor
Unsatisfactory washing results
The machine vibrates when spinning
The internal packing has not been removed. The machine is in contact with the wall or furniture. The machine is not level and stable (check diagonally). The washing load is badly distributed in the drum. Maybe there is very little laundry in the drum.

The door will not open

The water level is above the bottom edge of the door. The machine is heating the water. The drum is turning. The door can only be opened when the relevant light has gone out.
Spinning starts late or the machine does not spin
The machine makes an unusual noise
The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen several times before the unbalance disappears and normal spinning can resume. If, after 15 minutes, the laundry is still not evenly distributed in the drum, the machine will not spin. In this case, redistribute the load manually and select the spin programme. The machine is fitted with a type of motor which makes an unusual noise compared with other traditional motors. This new motor ensures a softer start and more even distribution of the laundry in the drum when spinning, as well as increased stability of the machine. Machines based on modern technology operate very economically using very little water without affecting performance.
No water is visible in the drum
Service & Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Zanussi Service Force Centre by telephoning:

Mo Pro d.. d. No.

929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.uk. Before calling out an engineer, please ensure you have read the details under the heading Something Not Working. When you contact the Service Force Centre you will need to give the following details: 1. Your name, address and post code 2. Your telephone number 3. Clear and concise details of fault 4. The model and serial number of the appliance (found on the rating plate - see picture). 5. The purchase date

Mod.. Prod. No.

P0042 BD

. Ser. No.

Ser. No.

Customer Care

For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please contact our Customer Care Department by letter or telephone as follows: Customer Care Department Zanussi 55-77 High Street Slough Berkshire SL1 1DZ Tel 08705 727727* or visit our website at www.zanussi.co.uk * calls to this number may be recorded for training purposes.

Guarantee Conditions

Standard guarantee conditions
We, Zanussi undertake that if, within 12 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity supply stated on the rating plate. The appliance has been used for normal domestic purposes only, and in accordance with the manufacturers instructions. The appliance has not been serviced, maintained, repaired, taken apart or tampered with, by any person not authorised by us. All service work under this guarantee must be undertaken by a Zanussi Service Force Centre. Any appliance or defective part replaced shall become the Companys property. This guarantee is in addition to your statutory and other legal rights. Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours in which case a premium will be charged.

Exclusions

This guarantee does not cover:
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable parts of glass or plastic. Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom. Appliances found to be in use within a commercial environment, plus those which are subject to rental agreements. Products of Zanussi manufacture which are NOT marketed by Zanussi.

European guarantee

If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications: The guarantee starts from the date you first purchased your product. The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products. The guarantee relates to you and cannot be transferred to another user. Your new home is within the European Community (EC) or European Free Trade Area. The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal household. The product is installed taking into account regulations in your new country. Before you move please contact your nearest Customer Care Centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Senlis +33 (0)Germany Nurnberg +49 (0)7378 Italy Pordenone +39 (0)4700 Sweden Stockholm +46 (0)UK Slough +44 (0)1753 219897

Special conditions

If the floor is carpeted or covered with crumbly or soft material, insert a rigid support base under the feet to prevent noise, vibration or displacement. The base should protrude a few centimetres beyond the edges of the machine. Warning The machine should NOT be placed on deep pile carpeting.
Before connecting up the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes.
Note Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown.

Levelling

Level the washing machine by raising or lowering the feet. The feet may be tight to adjust as they incorporate a self locking nut, but the machine MUST be level and stable (check diagonally).
Washing machines and dishwashers should be connected to the FOUL drainage system, the water will then be taken to a sewage works for treatment before being discharged safely into a river. It is essential that these appliances are not connected to the surface water drainage system as this water is discharged directly into a river or stream and may cause pollution. If you require any further advice please contact your local authority drainage department.
Any necessary adjustment can be made with a spanner. Accurate levelling prevents vibration, noise and displacement of the machine during operation. Some vibration is inevitable, especially if mounted on a wooden floor. Sprung wooden floors are particularly susceptible to vibration. For advice, consult a builder. If possible, always place the machine on a solid floor.

RAINWATER 'RUN-OFF'

SHOWER SINK BATH TOILET BIDET

WASHING MACHINE

DISHWASHER
FOUL DRAIN SURFACE WATER DRAINS & SEWERS FOUL SEWERS SEWAGE TREATMENT WORKS TREATED DISCHARGE RIVER RIVER

UNTREATED DISCHARGE

Electrical connection
Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING: THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should this safety measure not be observed. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliances rating plate. The rating plate is located at the top of the rim of the open door.
The wire coloured blue must be connected to the terminal marked N or coloured black. The wire coloured brown must be connected to the terminal marked L or coloured red. Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath. WARNING: A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that the cut off plug is disposed of safely. Should the appliance power supply cable neeed to be replaced, this should be carried out by our Service Force Centre. Note When the appliance is installed the power supply cable must be accessible.

Mo Pro d.. d. No. Ser. No.
The appliance is supplied with a 13amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13amp ASTA approved (BS1363/A) fuse must be used. Should the plug need to be replaced for any reason, proceed as described below. The wires in the mains lead are coloured in accordance with the following code: Green and Yellow - Earth Blue - Neutral Brown - Live

GREEN & YELLOW

E 13 A

Permanent connection

In the case of permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply (mains), with a minimum gap of 3mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations. The switch must not break the yellow and green earth cable at any point.

CORD CLAMP

The wire coloured green and yellow must be connected to the terminal marked with the letter E or by the earth symbol or coloured green and yellow.
From the Electrolux Group. The worlds No. 1 choice.
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.

Electrolux plc 2002