Contents

For the User
Important Safety Information Your New Washing Machine Description of the Appliance
Door locked light Detergent dispenser drawer Child safety feature 6-9
Something Not Working Service and Spare Parts Zanussi Guarantee Conditions Zanussi Service Force

19-21 22-23

For the Installer
Installation Instructions Technical Specifications
Unpacking Positioning Water inlet Water drainage Levelling Special conditions In the interest of the environment Electrical connection 27 28
The Control Panel Operating sequence
10-12 Load the laundry 10 Measure out the detergent 10 Measure out the fabric softener 10 Switch the machine on 10 Select the required programme/fabric 10 Select the temperature 11 Select the spin speed or the RINSE HOLD option 11 Select the desired options 11 Select the QUICK WASH option 11 Select the DELAY TIME 11 Start the programme 11 How to change a programme during its cycle 12 How to cancel a programme during its cycle 12 How to open the door during the cycle of a programme 12 End of programme 12

Washing Hints

Which detergent?. And in which form?

13-16 17-18 18

Wash Care Symbols Washing Programmes Maintenance and Cleaning
Descaling After each wash Maintenance Wash External cleaning Cleaning the dispenser drawer Cleaning the drawer recess Cleaning the filter The dangers of freezing Emergency emptying out
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions Hints and tips Environmental information

Your New Washing Machine

Your new washing machine, fitted with the Zanussi JET SYSTEM, meets all modern requirements for effective treatment of laundry with low water, energy and detergent consumption. Even small loads are washed economically because the amount of water used is regulated automatically according to the load and type of fabric.
Automatic cooling of the wash water to 60C before draining, with the 90C programme. This reduces thermal shock to fabrics, helping to prevent creasing. The special wool programme with its new delicate wash system treats your woollens with extreme care. The anti-unbalance device ensures that the washing machine remains stable when spinning.

In the interest of the environment

Ecological hints

To save water and energy and help protect the environment, we recommend that you follow these hints: G Normally soiled laundry may be washed without prewashing in order to save detergent, water and time (the environment is protected too!). G The machine works more economically if it is fully loaded. G With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed at a lower temperature. G Measure out detergent according to the water hardness, the degree of soiling and the quantity of laundry being washed.
Materials marked with the symbol are recyclable. Check with your local Council or Environmental Health Office to see if there are facilities in your area for re-cycling this appliance. When the appliance is to be scrapped, cut off the power supply cable and make the door lock device unusable to prevent young children from being trapped inside. Help to keep your country tidy - use authorised disposal sites for your old appliance.
How do we help to protect the environment? We use recycled paper!

Important

Your machine is fitted with a balance control device, which ensures the machine is stable during the spin. If the wash load appears not to have been spun sufficiently at the end of the wash cycle, because it is not evenly distributed in the drum, the balance control device may have operated. It will therefore be necessary to redistribute the wash load manually and select a spin programme. For more detailed information see the section headed Something Not Working.
Description of the Appliance
1 Detergent dispenser drawer 2 Control panel 3 Door locked light 4 Door opening handle 5 Filter 6 Adjustable feet

IN S PEE D

Door locked light
It stays on during the whole programme indicating that the door is locked. When the light goes out, the door can be opened (see page 12).
Detergent dispenser drawer
Prewash Main wash Fabric softener

Child safety feature

This machine incorporates a special child safety feature to prevent small children from being trapped inside the machine. To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin. To disable this device and restore the possibility of closing the door, rotate the button anti-clockwise until the groove is vertical.

The Control Panel

O N / OF F

PREWASH SUPER RINSE

FA B RI C

S TA R

T / PA U S E

R ESET

1 ON/OFF button
Press this button to switch the washing machine on. The display (8) will show three blinking dashes or a blinking zero. You will find more detailed explanations on page 7 (see DISPLAY). Press the ON/OFF button again to switch the machine off.

4 TEMPERATURE button

Press this button repeatedly to increase or decrease the temperature, if you want your laundry to be washed at a temperature different from the one proposed by the washing machine. The relevant light will light up. Maximum temperatures are 90C for cotton, 60C for synthetic fabrics, 40C for delicate fabrics, wool and fabrics to be hand-washed (HAND WASH programme). Important! By pressing the TEMPERATURE and SPIN SPEED buttons simultaneously, the acoustic signal at the end of the cycle is deactivated. By pressing these 2 buttons again the acoustic signal is reactivated.

2 MAINS-ON light

This light is connected to the ON/OFF button. It lights up when you press the button, and goes out when you press it again.

3 FABRIC button

Press this button repeatedly to select the programme on the basis of the type of laundry to be washed. The light relevant to the selected programme will light up. The washing machine will propose a temperature and automatically select the maximum spin value provided for the programme you have chosen. You can change these values by operating buttons 4 and 5. Hand wash When you select this programme, you obtain a particularly delicate washing, suitable for articles of clothing whose label indicates that they must be handwashed.

5 SPIN SPEED button

Press this button repeatedly to change the spin speed, if you want your laundry to be spun at a speed different from the one proposed by the washing machine. The relevant light will light up. Maximum speeds are: for cotton: 1,600, 1,200 or 1,000 rpm depending on the model; for synthetic fabrics, wool and fabrics to be handwashed: 900 rpm (850 rpm for IZ 10); for delicate fabrics: 700 rpm (650 rpm for IZ 10). RINSE HOLD position : when you choose this option, the machine will not drain the water of the last rinse, so as not to wrinkle the laundry. At the end of the cycle, the START/PAUSE button light will flash, to indicate that the water must be drained. To complete the cycle, choose one of the following options:
Draining and spin: - Press the START/PAUSE button. The machine will drain the water, then spin the laundry at the maximum speed provided for the selected programme. - Select spin speed by means of button 5, and press the START/PAUSE button. Drain only - Press the SKIP/RESET button once, so as to cause the DRAIN light to light up, then press the START/PAUSE button. Important! If you accidentally press the SKIP/RESET button more than once, the display will show three blinking dashes. To cause the washing machine to drain the water, select any washing programme by means of the FABRIC button, then press SKIP/RESET three times in order to select the DRAIN position (only the DRAIN light will remain lit).

8 Display

The following pieces of information are shown on the display: Three blinking dashes, when a programme is cancelled by means of the SKIP/RESET button. The three blinking dashes will also appear when you press the ON/OFF button to switch the machine on, if the previously selected cycle has been erased.
-- Duration of washing programme in hours and minutes, after you have selected a programme.

6 OPTIONS button

Press this button to select the following options: PREWASH: select this option if you wish your laundry to be prewashed before the main wash (not available for wool and hand-wash cycle). The prewash ends with a short spin at 650 rpm in programmes for cotton and synthetic fabrics, whereas in the programme for delicate fabrics the water is only drained. SUPER RINSE: this option can be selected with all programmes except the wool programme and hand wash. The machine performs 4 rinses instead of 3. This option is recommended for people who are allergic to detergents, and in areas where the water is very soft.

7 TIME SAVE button

This button allows you to select the QUICK WASH function, for laundry that is only slightly soiled (not for wool and HAND WASH programme). The washing time will be reduced according to the type of fabric and the selected temperature.
While the programme is running (after you have pressed the START/PAUSE button), the displayed time value decreases by one unit every minute. The washing machine has stopped with water in the tub, at the end of a programme with the RINSE HOLD option: this is indicated by a static zero. The washing machine has completed the programme: this is indicated by a blinking zero. At the same time, the door locked light goes out. The zero will reappear when you switch the washing machine on, unless the previous programme has been erased by means of the SKIP RESET button.
Important! The first time you use the washing machine, when you switch it on, it may display a blinking zero and give an audible warning signal. This is due to the fact that the washing machine has performed a washing cycle during the manufacturers inspection tests, and this cycle has not been erased after its completion. Delay start, a time value indicated in hours and selected by means of the relevant button.

9 START/PAUSE button

This button has three functions: Start: after you have selected the desired programme and options, press this button to start the washing machine. The light above the button will stop flashing and remain lit. If you have selected a delay time by means of button 11, the countdown will begin and will be shown on the display. Pause: when you press this button again, the programme in progress is interrupted. The light above the button will start flashing. To restart the programme, press the button again. When you PAUSE the cycle, the DOOR LOCKED light goes out, and it becomes possible to open the door, provided the washing machine is not in the heating phase; the level of the water is not high; the drum is not turning. Important! You must set the washing machine to PAUSE before you make any change in the programme in progress. Draining of water and spinning after the execution of programmes with the RINSE HOLD option.

The delay time is displayed for 5 seconds, then the duration of the selected programme reappears. After you have pressed the START/PAUSE button, the countdown begins, and the delay time value decreases by one unit every hour. You can delay the start of the selected programme by up to 24 hours in one hour intervals. An incorrect option selection has been made: this is indicated by the message Err when a function incompatible with the current programme is selected.

10 SKIP/RESET button

This button performs two functions: - Clears the memory - Selects special programmes At the end of every programme the RESET button must be pressed once or repeatedly to clear the programme memory. This will be confirmed by three dashes, flashing in the display. If the previous programme is not cleared, the display will show a 0 flashing and an audible signal will sound, when you switch the machine on. Selecting a special programme: A wash programme must be selected in the normal way. (START button not pressed)
The incorrect selection is also indicated by an audible warning signal. An alarm code indicates a fault in the machine operation (see the relevant chapter on page 19).

S TA R T / P A U S E

The SKIP button is then used to cancel or advance the programme to the required phase. The SKIP button can only operate when the programme is in pause. A normal wash cycle consists of the following phases, Wash - Rinses - Spin and is confirmed by the illumination of the corresponding LED,s.

11 DELAY button

This button makes it possible to delay the starting of the programme by up to 24 hours. The delay you have selected is shown on the display for about 5 seconds; afterwards, the duration of the programme reappears. You must select this option after you have set the programme and before you press the START/PAUSE button. The time value shown on the display will decrease by one unit every hour. You can change the delay time at any moment, before you press the START/PAUSE button. If you have already pressed the START/PAUSE button, and you wish to change or cancel the delay time, proceed as follows: set the washing machine to PAUSE by pressing the START/PAUSE button; press the DELAY button until the display shows the desired delay time or press the DELAY button once, to erase the delay time. The display will indicate 0h. press the START/PAUSE button again. Important! The door will be locked throughout the delay time (DOOR LOCKED light lit). If you need to open the door, you must first set the washing machine to PAUSE by pressing the START/PAUSE button. After you have closed the door, press the START/PAUSE button again.

To select rinse & spin, the programme must be paused, now press the SKIP button once, the wash LED goes out.
To select spin only, the programme must be paused, now press the SKIP button twice. The wash & rinse LED,s go out.
12 Programme phase indicator lights
When you select a programme, the lights relevant to the phases that form the programme light up.
To select Drain the programme must be paused, now press the SKIP button three times, the wash - rinse spin LED,s go out.

WASH RINSES SPIN DRAIN

After you have started the programme, only the light relevant to the phase that is currently being carried out will remain lit.

Operating Sequence

Before the first wash, we recommend that you run a cotton cycle at 60C, without any laundry in the machine, to remove any manufacturing residue from the drum and tub. Pour 1/2 a measure of detergent into the dispenser drawer and start the machine.

4. Switch the machine on

Press the ON/OFF button to switch the machine on. The display will show three blinking dashes or a blinking zero. The light above the button will light up.

O N / OFF

1.Load the laundry
Open the door. Place the laundry in the drum, one item at a time, shaking them out as much as possible. Close the door.
5. Select the desired programme/ fabric
Press the FABRIC button repeatedly, in order to select the desired programme/fabric. The relevant light will light up. The lights relevant to the phases that form the programme will light up. The display will show the duration of the selected programme, calculated on the basis of the maximum load for each type of fabric. The START/PAUSE button light will start flashing. If the load of laundry to be washed is small, at the beginning of the cycle the display will still indicate the duration relevant to the maximum load. The duration value will be gradually adjusted during the execution of the cycle.
2.Measure out the detergent
Pull out the dispenser drawer until it stops. Measure out the amount of detergent required and pour it into the main wash compartment. If you wish to carry out the prewash, pour detergent into the appropriate compartment marked.

After approximately 2 minutes, you can open the door. Pay attention to the level and temperature of the water in the washing machine! When you close the door and press the ON/OFF button again, the washing machine will resume the programme from the point where it had been interrupted.

15. End of programme

At the end of the programme, the washing machine stops automatically, gives an audible signal, and displays a blinking zero. If you had selected the RINSE HOLD option, the START/PAUSE button light flashes to indicate that the water must be drained. The display shows a steadily lit zero. When the programme has been completed, a blinking zero appears on the display and the audible signal is given. The DOOR LOCKED light goes out at once. Press the SKIP/RESET button repeatedly to erase the programme that has just been carried out. If you omit to do this, the next time you switch the washing machine on, the blinking zero will appear on the display and you will hear the audible signal. Note: when you switch the machine on, if you must erase the previously performed programme, it is also sufficient to press the FABRIC button and select a new programme. Press the ON/OFF button to switch the machine off. The relevant light will go out. Remove the laundry from the washing machine. Check whether the drum is completely empty, by rotating it with your hand. The purpose of this is to prevent any items of laundry from remaining accidentally in the drum, where they might get damaged in a subsequent wash (e.g. by shrinking) or bleed colour into another load of laundry. We advise you to close the water supply tap and disconnect the plug from the socket. Leave the door ajar in order to air the washing machine.
13. How to cancel a programme during its cycle
To cancel a programme that is being carried out, first pause the washing machine by pressing the START/PAUSE button, then press the SKIP/RESET button repeatedly, until the display shows three blinking dashes.
14. How to open the door during the cycle of a programme
You can open the door, after having set the washing machine to PAUSE, provided the following conditions exist: the washing machine is not in the heating phase beyond 40C; the level of the water is not high; the drum is not turning. If these requirements are met, when you pause the washing machine, the DOOR LOCKED light goes out and the door can be opened. Should it not be possible to open the door, and should it be absolutely necessary to do so, switch the machine off by pressing the ON/OFF button.

If the machine is unable to drain, proceed as follows to empty out the machine: G Pull out the plug from the power socket. G Close the water tap. G If necessary, wait until the water has cooled down. G Place a bowl on the floor under the filter and place the end of the emergency emptying hose into the bowl. The water should drain by gravity into the bowl. When the bowl is full, screw the cap on again. Empty the bowl. Repeat the procedure until water stops flowing out. G Clean the filter if necessary. G At the end screw the filter again.

The water inlet filter

If your water is very hard or contains traces of lime deposit, the water inlet filter may become clogged. It is therefore a good idea to clean it from time to time. Turn off the water tap. Unscrew the water inlet hose. Clean the filter using a hard bristle brush. Tighten up the inlet hose.

Something Not Working

Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Force Centre, please carry out the checks listed below. IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. During machine operation it is possible that one of the following alarm codes appears on the display: - E10 : problem with the water supply - E20 : problem with water draining - E40 : door open Once the problem has been eliminated, press the START/PAUSE button to restart the programme. If after all checks, the problem persists, contact your local Service Force Centre.

Symptom

The machine does not start

Possible causes

G G G G G G
The door has not been closed. (E40) The plug is not properly inserted in the power socket. There is no supply at the socket. The main fuse or the fuse in the plug has blown. The START/PAUSE button has not been depressed. The DELAY START option has been selected. The water tap is closed. (E10) The filter in the inlet hose is blocked. (E10) The inlet hose may be squashed or kinked. (E10) The door has not been closed. (E40) The end of the drain hose is too low. The end of the drain hose is submerged in water. There is no vent in the end of the drain hose. The drain hose may be squashed or kinked. (E20) The RINSE HOLD option has been selected. The drain filter may be blocked. (E20) The drain hose extension, if fitted, is not correct. Follow the instructions for connecting to the waste. The drainage system pipes are blocked. The wash load is unbalanced: redistribute the clothes inside the drum to allow the machine to spin. Too much detergent or unsuitable detergent has been used (creates too much foam). Check whether there are any leaks from the inlet hose fittings. It is not always easy to see this as the water runs down the hose; check to see if it is damp. The drain hose may be damaged or not securely positioned. The detergent dispenser drawer or recess is clogged. The drainage system pipes are blocked. Too little detergent or unsuitable detergent has been used. An insufficient amount of detergent leaves the laundry looking grey and causes lime scale to form. Stubborn stains have not been treated prior to washing The correct wash programme/temperature has not been selected. Too much laundry has been placed in the drum. 19

The machine does not fill

G G G G

The machine fills then empties immediately The machine does not empty and/or does not spin

G G G G G G G G G

There is water on the floor
Unsatisfactory washing results
The machine vibrates when spinning
The internal packing has not been removed. The machine is in contact with the wall or furniture. The machine is not level and stable (check diagonally). The washing load is badly distributed in the drum. Maybe there is very little laundry in the drum.

The door will not open

The water level is above the bottom edge of the door. The machine is heating the water. G The drum is turning. The door can only be opened when the relevant light has gone out.
Spinning starts late or the machine does not spin
The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen several times before the unbalance disappears and normal spinning can resume. If, after 15 minutes, the laundry is still not evenly distributed in the drum, the machine will not spin. In this case, redistribute the load manually and select the spin programme. The machine is fitted with a type of motor which makes an unusual noise compared with other traditional motors. This new motor ensures a softer start and more even distribution of the laundry in the drum when spinning, as well as increased stability of the machine. Machines based on modern technology operate very economically using very little water without affecting performance.
The machine makes an unusual noise
No water is visible in the drum
Service & Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Zanussi Service Force Centre by telephoning:

Customer Care

For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please contact our Customer Care Department by letter or telephone as follows: Customer Care Department Zanussi 55-77 High Street Slough Berkshire SL1 1DZ Tel 08705 727727* or visit our website at www.zanussi.co.uk * calls to this number may be recorded for training purposes.

929929

Your telephone call will be automatically routed to the Service Force Centre covering your post code area. The addresses are listed on the following pages. Before calling out an engineer, please ensure you have read the details under the heading Something Not Working. When you contact the Service Force Centre you will need to give the following details: 1. Your name, address and post code 2. Your telephone number 3. Clear and concise details of fault 4. The model and serial number of the appliance (found on the rating plate - see picture). 5. The purchase date

Mod.. Prod. No. Ser. No.

. d. No. Mo d. Pro

. No Ser

P0042N
Zanussi Guarantee Conditions
Standard guarantee conditions
We, Zanussi undertake that if, within 12 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: G The appliance has been correctly installed and used only on the electricity supply stated on the rating plate. G The appliance has been used for normal domestic purposes only, and in accordance with the manufacturers instructions. G The appliance has not been serviced, maintained, repaired, taken apart or tampered with, by any person not authorised by us. All service work under this guarantee must be undertaken by a Zanussi Service Force Centre. Any appliance or defective part replaced shall become the Companys property. This guarantee is in addition to your statutory and other legal rights. Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours in which case a premium will be charged.

Exclusions

This guarantee does not cover:
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable parts of glass or plastic. Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom. Appliances found to be in use within a commercial environment, plus those which are subject to rental agreements. Products of Zanussi manufacture which are NOT marketed by Zanussi.

European guarantee

If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications: G The guarantee starts from the date you first purchased your product. G The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products. G The guarantee relates to you and cannot be transferred to another user. G Your new home is within the European Community (EC) or European Free Trade Area. G The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal household. G The product is installed taking into account regulations in your new country. Before you move please contact your nearest Customer Care Centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Senlis +33 (0)Germany Nurnberg +49 (0)2600 Italy Pordenone +39 (0)Sweden Stockholm +46 (0)UK Slough +44 (0)1753 219897

1 Kelvin Park Dock Road Birkenhead CH41 1LT Unit 7 James Street Workshops James Street Carlisle Cumbria CA2 5AH South Quay Ind. Estate Douglas Isle of Man IM1 5AT Unit B Central Industrial Estate St Marks Street Bolton BL3 6NR Unit 250 Dawson Place Bamber Bridge Preston Lancashire PR5 8AL Unit 20 Haigh Park Haigh Avenue Stockport SK4 1QR

CARLISLE

GLASGOW

CARDIFF

ISLE OF MAN

INVERNESS

Unit 4 Guardian Industrial Estate Clydesmuir Road Cardiff CF2 2QS Unit 6-7 Coed Parc Abergele Road Rhuddlan Clwyd LL18 5UG Unit 9 St. Clears Business Park Tenby Road St. Clears Carmarthen SA33 4JW Plas Ffynnon Warehouse Middleton Road Oswestry SY11 2PP

BOLTON

ISLE OF ARRAN

PRESTON

ISLE OF BARRA

STOCKPORT

ISLES OF BUTE

OSWESTRY

SOUTH EAST

MIDLANDS

BIRMINGHAM

LONDON & EAST ANGLIA

BECKENHAM
66 Birch Road East Wyrley Trading Estate Witton Birmingham B6 7DB Pinfold Road Bourne PE10 9HT 68 St. Marys Street Bridgnorth Shropshire WV16 4DR 101 Rycroft Street Gloucester GL1 4NB Units 3 & 4 Bank Buildings Cattle market Hareford HE4 9HX Higham Ferrers Northants NN10 8PL Unit 2 Furnace Road Ilkeston DE7 5EP Unit 7 Oaks Industrial Estate Coventry Road Narborough Leicestershire LE9 5GF Unit 8 Clifton Street Stone Field Park Lincoln LN5 8LQ 18-21 Croft Road Brampton Ind. Estate Newcastle under Lyme Staffordshire ST5 0TW 13 Thornhill Road North Moons Moat Redditch Worcestershire B98 9ND Unit 3 Sterling Park Claymore Tamworth B77 5DQ Units 1 & 2 Northbrooks Close Gregorys Mill Ind. Estate Worcester WR3 8BP
11a Gardner Ind. Estate Kent House Lane Beckenham Kent BR3 1QZ Hanbury Road Widford Ind. Estate Chelmsford Essex CM12 3AE Unit 14 Capitol Park Capitol Way Colindale London NW9 0EQ 194 Court Road Mottingham Eltham London SE9 4EW 284 Alma Road Enfield London EN3 7BB Unit B4 Imperial Business Estate West Mill Gravesend Kent DA11 0DL Unit 6C Elton Park Business Centre Hadleigh Road Ipswich IP2 0DD 16-17 Woodside Ind. Park Works Road Letchworth Herts SG6 1LA 2 - 4 Royal Lane Yiewsley West Drayton Middlesex UB7 8DL Reform Road Maidenhead Berkshire SL6 8BY 10 Island Farm Avenue West Molesey Surrey KT8 2UZ 9 Pipers Court Berkshire Drive Thatcham Berkshire RG19 4ER 2b Trafalgar Street Norwich NR1 3HN Unit 1a The Summit Hanworth Road Sunbury on Thames TW16 5DB

ASHFORD

BOURNE BRIDGNORTH

CHELMSFORD

Unit 2 Bridge Road Business Centre Bridge Road Ashford Kent TN23 1BB Unit 1 Redfields Ind. Estate Church Crookham Fleet Hampshire GU13 0RD 21-25 Bridge Road Haywards Heath Sussex RH16 1UA Unit 30 Deacon Trading Estate Morley Road Tonbridge TN9 1RA

COLINDALE

GLOUCESTER HEREFORD

HAYWARDS HEATH

ELTHAM

TONBRIDGE

ENFIELD
HIGHAM FERRERS 30 High Street

GRAVESEND

SOUTH WEST

BARNSTAPLE

ILKESTON LEICESTER

IPSWICH

Main Road Fremington Barnstaple North Devon EX31 2NT Bournemouth Dorset BH1 4PW
BOURNEMOUTH 63-65 Curzon Road

LINCOLN

LETCHWORTH

BRIDGEWATER

6 Herswell Business Park Salmon Parade Bridgwater Somerset TA6 5PY 11 Eldon Way Eldonwall Trading Estate Bristol BS4 3QQ 266 Main Road Southbourne Emsworth PO10 8JL Unit 8 Enterprise Court Ryde Business Park Ryde Isle of Wight PO33 1DB Zealley Ind. Estate Kingsteignton Newton Abbot TQ12 3TD Unit 7D Pool Ind. Estate Druids Road Redruth Cornwall TR15 3RH

NEWCASTLE UNDER LYME

LONDON

BRISTOL

MAIDENHEAD

EMSWORTH

REDDITCH

MOLESEY

ISLE OF WIGHT

TAMWORTH

NEWBURY

NEWTON ABBOT Unit 2

WORCESTER

NORWICH

REDRUTH

SUNBURY

Installation Instructions
It is dangerous to alter the specifications or attempt to modify this product in any way. Care must be taken to ensure that the appliance does not stand on the electrical supply cable. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person.

Technical Specifications

DIMENSIONS Height Width Depth 85 cm 60 cm 62 cm 230-240 V/50 Hz 2050 W (13A) Minimum Maximum Cotton, linen Synthetics Delicate fabrics Wool Maximum 50 kPa (0.5 bar) 800 kPa (8 bar) 5 kg (max 6 kg) 2.5 kg 2.5 kg 2 kg 1000 rpm (IZ 10) 1200 rpm (IZ 12) 1600 rpm (IZ 16 - IZ 16 S) 0.95 kWh 42 litres (IZ 16 - IZ 16 S) 49 litres (IZ 10 - IZ 12) POWER SUPPLY VOLTAGE TOTAL POWER ABSORBED WATER PRESSURE MAXIMUM RECOMMENDED LOAD

SPIN SPEED

CONSUMPTION DATA FOR WASHING 5 KG NORMALLY SOILED COTTON ITEMS AT 60C

Energy Water

This appliance complies with the following E.E.C. Directives: - 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.