Contents

For the User
Important Safety Information Your New Washing Machine Description of the Appliance
Door locked light Detergent dispenser drawer Child safety feature 6-9
Something Not Working Service and Spare Parts Zanussi Guarantee Conditions Zanussi Service Force

19-21 22-23

For the Installer
Installation Instructions Technical Specifications
Unpacking Positioning Water inlet Water drainage Levelling Special conditions In the interest of the environment Electrical connection 27 28
The Control Panel Operating sequence
10-12 Load the laundry 10 Measure out the detergent 10 Measure out the fabric softener 10 Switch the machine on 10 Select the required programme/fabric 10 Select the temperature 11 Select the spin speed or the RINSE HOLD option 11 Select the desired options 11 Select the QUICK WASH option 11 Select the DELAY TIME 11 Start the programme 11 How to change a programme during its cycle 12 How to cancel a programme during its cycle 12 How to open the door during the cycle of a programme 12 End of programme 12

Washing Hints

Which detergent?. And in which form?

13-16 17-18 18

Wash Care Symbols Washing Programmes Maintenance and Cleaning
Descaling After each wash Maintenance Wash External cleaning Cleaning the dispenser drawer Cleaning the drawer recess Cleaning the filter The dangers of freezing Emergency emptying out
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions Hints and tips Environmental information

Your New Washing Machine

Your new washing machine, fitted with the Zanussi JET SYSTEM, meets all modern requirements for effective treatment of laundry with low water, energy and detergent consumption. Even small loads are washed economically because the amount of water used is regulated automatically according to the load and type of fabric.
Automatic cooling of the wash water to 60C before draining, with the 90C programme. This reduces thermal shock to fabrics, helping to prevent creasing. The special wool programme with its new delicate wash system treats your woollens with extreme care. The anti-unbalance device ensures that the washing machine remains stable when spinning.

The Control Panel

O N / OF F

PREWASH SUPER RINSE

FA B RI C

S TA R

T / PA U S E

R ESET

1 ON/OFF button
Press this button to switch the washing machine on. The display (8) will show three blinking dashes or a blinking zero. You will find more detailed explanations on page 7 (see DISPLAY). Press the ON/OFF button again to switch the machine off.

4 TEMPERATURE button

Press this button repeatedly to increase or decrease the temperature, if you want your laundry to be washed at a temperature different from the one proposed by the washing machine. The relevant light will light up. Maximum temperatures are 90C for cotton, 60C for synthetic fabrics, 40C for delicate fabrics, wool and fabrics to be hand-washed (HAND WASH programme). Important! By pressing the TEMPERATURE and SPIN SPEED buttons simultaneously, the acoustic signal at the end of the cycle is deactivated. By pressing these 2 buttons again the acoustic signal is reactivated.

2 MAINS-ON light

This light is connected to the ON/OFF button. It lights up when you press the button, and goes out when you press it again.

3 FABRIC button

Press this button repeatedly to select the programme on the basis of the type of laundry to be washed. The light relevant to the selected programme will light up. The washing machine will propose a temperature and automatically select the maximum spin value provided for the programme you have chosen. You can change these values by operating buttons 4 and 5. Hand wash When you select this programme, you obtain a particularly delicate washing, suitable for articles of clothing whose label indicates that they must be handwashed.

5 SPIN SPEED button

Press this button repeatedly to change the spin speed, if you want your laundry to be spun at a speed different from the one proposed by the washing machine. The relevant light will light up. Maximum speeds are: for cotton: 1,600, 1,200 or 1,000 rpm depending on the model; for synthetic fabrics, wool and fabrics to be handwashed: 900 rpm (850 rpm for IZ 10); for delicate fabrics: 700 rpm (650 rpm for IZ 10). RINSE HOLD position : when you choose this option, the machine will not drain the water of the last rinse, so as not to wrinkle the laundry. At the end of the cycle, the START/PAUSE button light will flash, to indicate that the water must be drained. To complete the cycle, choose one of the following options:

Important! The first time you use the washing machine, when you switch it on, it may display a blinking zero and give an audible warning signal. This is due to the fact that the washing machine has performed a washing cycle during the manufacturers inspection tests, and this cycle has not been erased after its completion. Delay start, a time value indicated in hours and selected by means of the relevant button.

9 START/PAUSE button

This button has three functions: Start: after you have selected the desired programme and options, press this button to start the washing machine. The light above the button will stop flashing and remain lit. If you have selected a delay time by means of button 11, the countdown will begin and will be shown on the display. Pause: when you press this button again, the programme in progress is interrupted. The light above the button will start flashing. To restart the programme, press the button again. When you PAUSE the cycle, the DOOR LOCKED light goes out, and it becomes possible to open the door, provided the washing machine is not in the heating phase; the level of the water is not high; the drum is not turning. Important! You must set the washing machine to PAUSE before you make any change in the programme in progress. Draining of water and spinning after the execution of programmes with the RINSE HOLD option.
The delay time is displayed for 5 seconds, then the duration of the selected programme reappears. After you have pressed the START/PAUSE button, the countdown begins, and the delay time value decreases by one unit every hour. You can delay the start of the selected programme by up to 24 hours in one hour intervals. An incorrect option selection has been made: this is indicated by the message Err when a function incompatible with the current programme is selected.

10 SKIP/RESET button

This button performs two functions: - Clears the memory - Selects special programmes At the end of every programme the RESET button must be pressed once or repeatedly to clear the programme memory. This will be confirmed by three dashes, flashing in the display. If the previous programme is not cleared, the display will show a 0 flashing and an audible signal will sound, when you switch the machine on. Selecting a special programme: A wash programme must be selected in the normal way. (START button not pressed)

900 700

8. Select the desired options
If your laundry is very dirty, it may be advisable to select the PREWASH option. If you wish the laundry to undergo an extra rinse, select the SUPER RINSE option. Press the OPTIONS button so as to cause one or both of the lights to light up.
10. Select the DELAY TIME
Before you start the programme, if you wish the starting to be delayed, press the DELAY button repeatedly, or keep it pressed, to select the desired delay. The selected delay time value (up to 24 hours) will appear on the display for 5 seconds, then the duration of the programme will appear again.

N SPEE

11. Start the programme
Press the START/PAUSE button. The relevant light will stop flashing, the DOOR LOCKED light will light up, and only the light relevant to the phase that is in progress will remain lit. If you have chosen a delayed start, the washing machine will begin the countdown. The display will show the duration of the programme or the selected delay.

TIO N S

12. How to change a programme during its cycle
Before you make any change, you must pause the washing machine by pressing the START/PAUSE button. It is possible to change any phase before the programme carries it out. Changing the type of fabric or temperature is possible, obviously, only during the washing phase. When you make a change in these two parameters, the washing machine will resume the cycle from the beginning. If it is necessary to drain the water in order to change the programme in progress, proceed as follows: PAUSE the machine by pressing the START/PAUSE button; press the SKIP/RESET button repeatedly, until only the DRAIN light remains lit; press the START/PAUSE button again. When the water has been drained, the display shows a blinking zero. You may now select a new programme and press the START/PAUSE button to start it.
After approximately 2 minutes, you can open the door. Pay attention to the level and temperature of the water in the washing machine! When you close the door and press the ON/OFF button again, the washing machine will resume the programme from the point where it had been interrupted.

15. End of programme

At the end of the programme, the washing machine stops automatically, gives an audible signal, and displays a blinking zero. If you had selected the RINSE HOLD option, the START/PAUSE button light flashes to indicate that the water must be drained. The display shows a steadily lit zero. When the programme has been completed, a blinking zero appears on the display and the audible signal is given. The DOOR LOCKED light goes out at once. Press the SKIP/RESET button repeatedly to erase the programme that has just been carried out. If you omit to do this, the next time you switch the washing machine on, the blinking zero will appear on the display and you will hear the audible signal. Note: when you switch the machine on, if you must erase the previously performed programme, it is also sufficient to press the FABRIC button and select a new programme. Press the ON/OFF button to switch the machine off. The relevant light will go out. Remove the laundry from the washing machine. Check whether the drum is completely empty, by rotating it with your hand. The purpose of this is to prevent any items of laundry from remaining accidentally in the drum, where they might get damaged in a subsequent wash (e.g. by shrinking) or bleed colour into another load of laundry. We advise you to close the water supply tap and disconnect the plug from the socket. Leave the door ajar in order to air the washing machine.
13. How to cancel a programme during its cycle
To cancel a programme that is being carried out, first pause the washing machine by pressing the START/PAUSE button, then press the SKIP/RESET button repeatedly, until the display shows three blinking dashes.
14. How to open the door during the cycle of a programme
You can open the door, after having set the washing machine to PAUSE, provided the following conditions exist: the washing machine is not in the heating phase beyond 40C; the level of the water is not high; the drum is not turning. If these requirements are met, when you pause the washing machine, the DOOR LOCKED light goes out and the door can be opened. Should it not be possible to open the door, and should it be absolutely necessary to do so, switch the machine off by pressing the ON/OFF button.
Do NOT overload the machine. Weigh the laundry the first few times you use the appliance. The average weights of the most common items are listed below as a guide: 1000g = 1 kg Sheet Pillow case Tablecloth Serviette Tea towel Linen hand towel Towelling hand towel Towelling bath towel Bath robe Mans shirt Apron 700-1000 g 100-200 g 400-500 g 50-100 g 70-120 g 100-150 g 150-250 g 700-1000 g 1000-1500 g 200-300 g 150-200 g

G G G G G

Bleach is very corrosive; it should be used with care and kept out of reach of children. Some stains such as fruit, wine, grass, rust etc. are difficult to remove and should be treated before washing with specific products, which can be found in most household shops. In some cases it may help to soak the stain before washing with a special presoak product or biological detergent. Only wool marked Pure New Wool - washable, preshrunk can be washed in the machine using the wool programme; other types of wool should be washed by hand or dry cleaned. If you have used the machine to wash, rinse or spin only non-colour fast garments, there may be dye left in the sump. To ensure any subsequent wash is not contaminated with the dye, select and carry out a rinse and spin programme, without any garments, to ensure that any dye is removed from the sump. Once you have finished using the machine, you are advised to unplug it and turn off the water tap.

JETSYSTEM wash

Load the laundry loosely alternating large items with small ones. Sort the laundry according to the type of fabric, colour-fastness and how dirty it is. Avoid washing unhemmed or torn items as they may unravel. Before washing, empty all pockets of small objects which may have been left inside (coins, keys, screws etc). as these could damage the drain pump. When washing curtains, remove the hooks. Close poppers and zips and fasten loose buttons. It is essential to wash new coloured items separately when washing for the first time. When washing fabrics requiring different wash temperatures together, always select the lowest temperature. White items should not be washed with coloured items. Very small items (handkerchiefs, ribbons, socks etc) should be washed in a washing bag or a pillow case. Use a good quality detergent suitable for automatic washing machines. Use the correct quantities of detergent. For wool, use gentle detergent only in small quantities. 13
As the Jetsystem is flexible and adjusts water intake according to wash load size it is not possible to give you exact recommandations as to the amount of detergent that should be used for any one wash. Therefore we recommend that you use approximately 1/3 less than the detergent manufacturer recommends on the packet or bottle, making the appropriate allowances for soft or hard water, and light or heavy soilage of clothes. If you have judged the amount correctly you should expect to see a soft sudsy liquid during the wash. It is not necessary to have a head of lather on the water.

BLEACHING Chlorine bleach may be used IRONING Hot iron Warm iron Cool iron DRY CLEANING May be dry cleaned. Other letters and/or a bar beneath the circle will indicate the required process to the dry cleaner. TUMBLE DRYING with high heat setting with low heat setting May be tumble dried Cotton, Linen, Viscose Polyester mixtures, Wool Acrylic, Nylon, Polyester
A cross through any symbol means DO NOT fabric conditioner to avoid the conditioner entering the machine prematurely. When using liquid detergent and a prewash programme, place the detergent into the correct compartment in the dispenser drawer, after the prewash has finished. 15

Important Notes

For best results, always use the dispenser drawer for dispensing detergents and liquid additives. Once the dispenser has been filled, close it by pushing it in gently. This is particularly important if you are using

Washing programmes

Type of laundry and symbols on labels
Programme/ temperature Cottons 60-90C
Description of programme Main wash at 60-90C 3 rinses Long spin
Consumption* Available options Energy kWh 1.8 Water litres 45 (52 for IZ10 and 12) Time h/min. 2.29
White cotton: e.g. sheets, tablecloths, household linen
SPIN SPEED RINSE HOLD PREWASH SUPER RINSE QUICK SPIN SPEED RINSE HOLD PREWASH SUPER RINSE QUICK
Coloured cotton: e.g. shirts, blouses, underwear, towels, household linen
Main wash at Cottons 60-40-30C 60-40-30C 3 rinses Long spin
42 (49 for IZ10 and IZ12)

2.5 kg

Synthetic fabrics and blends: e.g. shirts, blouses, underwear

Synthetics 60-50-4030C

Main wash at 60-50-4030C 3 rinses Short spin Main wash at 40-30C 3 rinses Short spin
SPIN SPEED RINSE HOLD PREWASH SUPER RINSE QUICK SPIN SPEED (only IZ10 and 12) RINSE HOLD PREWASH SUPER RINSE QUICK
Delicate fabrics: e.g. acrylic fabrics, viscose, polyester, synthetic blends

Delicates 40-30C

Wool 40-30C
Main wash at 40-30C 3 rinses Short spin Main wash at 40-30C 3 rinses Short spin

SPIN SPEED RINSE HOLD

Hand wash 40-30C
The coloured cotton programme at 60C is the reference programme for the data entered in the energy label, in compliance with EEC 92/75 standards. * This data is given purely as an indication: the consumption values may vary in relation to the quantity and type of laundry, the temperature of the water supply and the ambient temperature. The data refers to the highest temperature provided for each programme. The machine is capable of washing up to 6 kg, however, to achieve optimum wash results it is recommended that the above wash loads are adhered to.

Mod.. Prod. No. Ser. No.

. d. No. Mo d. Pro

. No Ser

P0042N
Zanussi Guarantee Conditions
Standard guarantee conditions
We, Zanussi undertake that if, within 12 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: G The appliance has been correctly installed and used only on the electricity supply stated on the rating plate. G The appliance has been used for normal domestic purposes only, and in accordance with the manufacturers instructions. G The appliance has not been serviced, maintained, repaired, taken apart or tampered with, by any person not authorised by us. All service work under this guarantee must be undertaken by a Zanussi Service Force Centre. Any appliance or defective part replaced shall become the Companys property. This guarantee is in addition to your statutory and other legal rights. Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours in which case a premium will be charged.

Exclusions

This guarantee does not cover:
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable parts of glass or plastic. Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom. Appliances found to be in use within a commercial environment, plus those which are subject to rental agreements. Products of Zanussi manufacture which are NOT marketed by Zanussi.

European guarantee

If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications: G The guarantee starts from the date you first purchased your product. G The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products. G The guarantee relates to you and cannot be transferred to another user. G Your new home is within the European Community (EC) or European Free Trade Area. G The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal household. G The product is installed taking into account regulations in your new country. Before you move please contact your nearest Customer Care Centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Senlis +33 (0)Germany Nurnberg +49 (0)2600 Italy Pordenone +39 (0)Sweden Stockholm +46 (0)UK Slough +44 (0)1753 219897

To contact your local Service Force Centre telephone 08705

929 929

NORTH EAST

CHANNEL ISLANDS

GUERNSEY

ISLE OF LEWIS

Guernsey Electricity PO Box 4 Vale, Guernsey Channel Islands GY1 3AD Jersey Electricity Company Haut De Lorme Rue De Haut De Lorme Trinity Jersey Channel Islands JE3 5FG
ND Macleod 16 James Street Stornoway Isle of Lewis PA87 2QW 2, 6 & 8 Woodmarket Kelso Borders TD5 7AX 7 King Street Kirkwall Orkney KW15 1JF Scottish Hydro Electric Central Warehouse Inveralmond Perth PH1 3AF 3-4 Carlton Place Lerwick Shetland ZE1 0PW Bolts Shetland 26 North Road Lerwick Shetland ZE1 0PE Leask Electrical Harisdale Symbister, Whalsay Shetland ZE2 9AA

GATESHEAD

Unit 356a Dukesway Court Dukesway Gateshead NE11 0BH 15 Hainton Avenue Grimsby N. E. Lincs DN32 9AS Unit 1 Boulevard Industrial Estate Hull HU3 4AY 64-66 Cross Gates Road Cross Gates Leeds LS15 7YS Unit 23 Northfield Way Aycliffe Industrial Park Newton Aycliffe DL5 6EJ Pennine House Roman Ridge Road Sheffield S9 1GB

JERSEY

GRIMSBY

ORKNEY

SCOTLAND

ABERDEEN

54 Claremont Street Aberdeen AB10 6RA 33a Burnside Auchtermuchty Fife KY14 7AJ Unit 5 Block 2 Auchenraith Ind. Estate Rosendale Way Blantyre G72 0NJ 93 Irish Street Dumfries DGPQ 7 Hill Street Dunoon Argyll PA23 7AL Unit 12 Dumbryden Ind. Estate 2 Dumbryden Road Edinburgh EH14 2AB Unit 4 Wellington Road Bishopriggs Glasgow G64 2SA Unit 3BI Smithton Ind. Estate Smithton Inverness IV2 7WL R Haggerty Bruach Blackwaterfoot Isle of Arran J Zerfah 244 Bruernish Isle of Barra Western Islands HS9 5QY Walker Engineering Glenmhor Upper Serpentine Road Rothesay Isle of Bute PA20 9EH

(OWN SALES) SHETLAND

AUCHTERMUCHTY

NEWTON AYCLIFFE

BLANTYRE

(OWN SALES) WHALSAY

SHEFFIELD

DUMFRIES

DUNOON

(OWN SALES)

NORTH WEST

BIRKENHEAD

NORTHERN IRELAND

BELFAST

EDINBURGH
Owenmore House Kilwee Business Park Dunmurry Belfast BT17 0HD

Positioning

Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine does not touch the wall or other kitchen units. Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor. Your new washing machine has been designed to be permanently plumbed in to your homes water supply and drainage system. However, if this is not possible, it may be connected to a suitable existing tap with the drain hose discharging into a sink. The appliance has an inlet hose, with female 3/4 BSP thread connector. If this connection is not compatible with the plumbing of the existing installation, a variety of connectors are available from good hardware stores and plumbers merchants to suit most domestic plumbing. Any alteration to your existing plumbing must be carried out by a competent person, or qualified plumber.
Remove the polystyrene block from the bottom of the machine and release the two plastic bags. Carefully slide out the right polythene bag (1). Repeat the operation for the left polythene bag (2).
Installation on a Suspended Floor
Suspended wooden floors are particularly susceptible to vibration. To help prevent vibration we recommend you place a waterproof wood panel, at least 15 mm thick under the appliance, secured to at least 2 floor beams with screws. If possible install the appliance in one of the corners of the room, where the floor is more stable.

P1068 P1066

Remove the polystyrene base. Set the machine upright and remove the two remaining bolts from the back. Pull out the three plastic spacers from the holes into which the bolts were fitted. Plug all the holes with the plugs supplied with the instruction booklet.

Water inlet

Connect the hose to a tap with a 3/4 thread.
Installation should comply with local water authority and building regulations requirements. The appliance must be connected to a cold water supply. A minimum water pressure of 50 kPa (0.5 bar) is required for safe operation of the appliance.

If you cannot make the cold water connection direct from the rising mains, you may be able to operate the appliance from your cold water storage system. There should be a minimum distance of 5.02m (16.5 ft) between the appliances inlet and the bottom of the water storage tank. Set the hose correctly by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks.
When discharging into a standpipe ensure that the top of the curve in the hose end is no more than 90cm (35.4'') and no less than 60cm (23.6'') above floor level. The upright standpipe should have a minimum length of 30cm (12'') from the bottom of the elbow to the top of the pipe (see diagram). Make sure that it is designed in such a way, that the end of the drain hose cannot be covered with water. The drain hose may be extended to a maximum of 4 metres. An additional drain hose and joining piece is available from your local Service Force Centre. The joining piece must have an internal diameter of 18mm. If you intend the drain hose to empty into a sink, make sure that the sink is empty and the plug hole is not blocked. Use the plastic U-Piece supplied.

Water drainage

This appliance is designed to be permanently plumbed into your home's water supply and drainage system.

Max. 90 cm.(35.4")

Min.60 cm. (23.6")
Before connecting up the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes.
The appliance drain hose should hook into a standpipe, the hook in the drain hose is formed using the plastic U-Piece supplied. The standpipe should have an internal diameter of approximately 38mm (see diagram) thus ensuring there is an air break between the drain hose and standpipe.
mm.(1/2") diameter standpipe

Min. 30 cm.(12")

Levelling
Level the washing machine by raising or lowering the feet. The feet may be tight to adjust as they incorporate a self locking nut, but the machine MUST be level and stable (check diagonally).

Washing machines and dishwashers should be connected to the FOUL drainage system, the water will then be taken to a sewage works for treatment before being discharged safely into a river. It is essential that these appliances are not connected to the surface water drainage system as this water is discharged directly into a river or stream and may cause pollution. If you require any further advice please contact your local water authority.
Any necessary adjustment can be made with a spanner. Accurate levelling prevents vibration, noise and displacement of the machine during operation. Some vibration is inevitable, especially if mounted on a wooden floor. Sprung wooden floors are particularly susceptible to vibration. For advice, consult a builder. If possible, always place the machine on a solid floor.
SHOWER SINK BATH TOILET BIDET

Special conditions

If the floor is carpeted or covered with crumbly or soft material, insert a rigid support base under the feet to prevent noise, vibration or displacement. The base should protrude a few centimetres beyond the edges of the machine. Warning The machine should NOT be placed on deep pile carpeting.
WASHING MACHINE RAINWATER 'RUN-OFF' DISHWASHER
FOUL DRAIN SURFACE WATER DRAINS & SEWERS FOUL SEWERS SEWAGE TREATMENT WORKS TREATED DISCHARGE RIVER RIVER

UNTREATED DISCHARGE

Note Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown.

Electrical connection

Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING: THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should this safety measure not be observed. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliances rating plate. The rating plate is located at the top of the rim of the open door.
The wire coloured brown must be connected to the terminal marked L or coloured red. Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath. WARNING: A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that the cut off plug is disposed of safely. The power supply cable must be easily accessible after installing the appliance.

Permanent connection

In the case of permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply (mains), with a minimum gap of 3mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations. The switch must not break the yellow and green earth cable at any point.
The appliance is supplied with a 13amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13amp ASTA approved (BS1362A) fuse must be used. Should the plug need to be replaced for any reason, proceed as described below. The wires in the mains lead are coloured in accordance with the following code: Green and Yellow - Earth Blue - Neutral Brown - Live

GREEN & YELLOW

E 13 A N L

CORD CLAMP

The wire coloured green and yellow must be connected to the terminal marked with the letter E or by the earth symbol or coloured green and yellow. The wire coloured blue must be connected to the terminal marked N or coloured black.
From the Electrolux Group. The worlds No. 1 choice.
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
Electrolux Household Appliances Limited 2001