132969940.qxd

02/10/2007

Pagina

User manual

Washerdryer

ZKG 2125
Thank you for selecting our appliance
We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance.
The following symbols are used in this manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. General information and tips Environmental information

Content

Safety information - - - - - - - - - - - - - - - - - - -3 Description of the appliance - - - - - - - - - - - -5 Detergent dispenser drawer - - - - - - - - - - - -5 Control panel and functions - - - - - - - - - -6-8 Programme table - - - - - - - - - - - - - - - - -9-10 Programme information - - - - - - - - - - - - - -11 Washing and drying hints - - - - - - - - - - - - -11 Before the first use - - - - - - - - - - - - - - - - -15 Operating Sequence - - - - - - - - - - - - - - - -15 Washing - - - - - - - - - - - - - - - - - - - - - - - - -Drying - - - - - - - - - - - - - - - - - - - - - - - - - -19 Drying programmes - - - - - - - - - - - - - - - - -20 Care and cleaning - - - - - - - - - - - - - - - - - -21 Something not working - - - - - - - - - - - - - - 24 Technical data- - - - - - - - - - - - - - - - - - - - - 28 Consumption values - - - - - - - - - - - - - - - - 29 Installation instruction - - - - - - - - - - - - - - - 30 Environmental concerns - - - - - - - - - - - - - 33 Guarantee - - - - - - - - - - - - - - - - - - - - - 34-35

Safety information

In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety.
Always unplug the appliance and turn off the water supply after use, clean and maintenance. Under no circumstances should you attempt to repair the machine yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local Service Centre. Always insist on genuine spare parts.

Installation

General safety
It is dangerous to alter the specifications or attempt to modify this product in any way. During high temperature washing and drying programmes the door glass may get hot. Do not touch it! Make sure that small pets do not climb into the drum. To avoid this, please check into the drum before using. Any objects such as coins, safety pins, nails, screws, stones or any other hard, sharp material can cause extensive damage and must not be placed into the machine. Only use the advised quantities of fabric softener and detergent. Damage to the fabric can ensue if you over-fill. Refer to the manufacturers recommendations of quantities. Wash small items such as socks, laces, washable belts etc in a washing bag or pillow case as it is possible for such items to slip down between the tub and the inner drum. Do not use your washer-dryer to wash articles with whalebones, material without hems or torn material.

Child safety

This appliance is not intended for use by person (including children) with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Young children should be supervised to ensure that they do not play with the appliance. The packaging components (e.g. plastic film, polystyrene) can be dangerous to children danger of suffocation! Keep them out of childrens reach Keep all detergents in a safe place out of childrens reach. Make sure that children or pets do not climb into the drum. To avoid this the machine incorporates special feature.
To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin.
To disable this device and restore the possibility of closing the door, rotate the button anti-clockwise until the groove is vertical.
Description of the appliance
5 Detergent dispenser drawer Control panel Door opening handle Drain pump Adjustable feet
Detergent dispenser drawer
Prewash Wash Fabric Softener
Control panel and functions

700 500

Henceforth, the programme selector dial, the different buttons and the programme progress display will be indicated in all the book with the relevant numbers given in the table below. Programme selector dial symbols: = White/Coloured cottons, = Economy, Jeans, = Sport, = Prewash, = Rinsing, = Synthetics, = Easy Iron, = Draining , = Delicates, = Spinning = Schage = Cold Wash, =

= Handwash,

Key symbols Control Panel: = Rinse Hold option, = Iron dry option and Quick option, light and = Spin reduction button, = Store dry option = Electronic drying button, = Super = Door locked
= Timed drying button, , = Start Pause button,

= Extra Rinse button,

= Delay start option.
Programme selector dial and On/Off switch
The programme selector dial allows to select a programme and/or to switch the machine on/off. It can be turned either clockwise or anticlockwise. The light Start/Pause starts to flash.

2 Spin reduction button

Press the Spin button repeatedly to change the spin speed, if you want your laundry to be spun at a speed different from the one proposed by the washer-dryer or to select the Rinse Hold option. The relevant light will light up. By means of this button you can choose the required degree of drying for cottons and synthetics between: Cupboard dry (cottons and synthetics) and Iron dry (cottons).The corresponding pilot light illuminates. By depressing this button you can select a timed programme for cotton or synthetics, the relevant phase light illuminates. With this option it is possible to reduce the washing time for lightly soiled laundry.
3 Automatic Drying button

4 Drying Time button

5 Super Quick button 6 Extra Rinse button 7 Display
By means of this button, the machine performs some additional rinses. The display shows the following information: duration of the selected programme, selected drying time, incorrect option selection, alarm codes, child safety lock and end of programme.

8 Start/Pause button

The Start/Pause button allows to start the selected programme; the corresponding green pilot light stops flashing. This button interrupts also a programme which is running, the corresponding green pilot light starts to flash.

9 Door locked light

The Door locked light indicates when it is possible to open the door. With this function,the wash programme can be delayed up to 20 hours to a more convenient for you time.

10 Delay Start button

Functions

Rinse hold (Button 2)

By selecting this option, the machine will not drain the water of the last rinse to prevent the fabrics from creasing. When the programme has finished, the light of the button 8 goes off and the light 9 illuminates. The door is locked to indicate that the water must be emptied out. To empty out the water see chapter At the end of the programme. The washing time will be reduced according to the type of fabric and the selected temperature

Extra rinse (Button 6)

The machine performs some additional rinses during the washing cycle. This option is recommended for people who are allergic to detergents, and in areas where the water is very soft.

Door locked light (9)

Automatic drying (Button 3)
By means of this button you can choose the required degree of drying for cottons and synthetics between: Cupboard dry (cottons and synthetics) and Iron dry (cottons). The corresponding pilot light illuminates. The drying time is automatically adjusted by the machine: the laundry will be dried to the selected degree of dryness.
Drying Time button (Button 4)
By depressing this button you can select a timed programme for cotton or synthetics. The relevant light illuminates. For Cottons and Synthetics you can select a drying time from 10 minutes to 130 minutes (2.10). Every time you press the button the time increases by 5 mins. Note! The programme time will automatically increase by up to 2 minutes. this is quite normal.
This light illuminates after pressing button 8. The light 9 indicates when the door can be opened: light on: the door is locked and cannot be opened. The washing or the drying cycle starts working and the door is locked. light off: the door can be opened. The washing programme has finished. If there is water left in the tub, the light 9 remains lit. The door will be still locked and it will be necessary to empty out before opening the door. To empty out the water see chapter At the end of the programme.

Delay start (Button 10)

The wash programme can be delayed from 30 min - 60 min - 90 min, 2 hours and then by 1 hour up to a maximum of 20 hours. The Delay start cannot be selected with Drain programme.

Super Quick (Button 5)

Short cycle for lightly soiled items or for laundry that have been used or worn for a short time and needs only freshening up. We recommend you to reduce the fabrics loading.

Programme table

Programme/ Temperature Cottons 90 - 60 Type of laundry White cotton (heavy soiled cotton items) White and fast colour cotton (normally soiled cotton items) White and colour cotton (heavy soiled cotton items) White cotton (white cotton items heavily soiled ) White cotton and fast colour cotton (cotton items normally soiled ) Cotton colour (cotton colour items normally soiled ) Options Description of programme
Main wash Rinses Spin red./ Super Quick, Extra rinse Long spin at the maximum speed Spin red./ Extra rinse Main wash Rinses Long spin at the maximum speed

Cottons 60 Eco

Cottons 60 - 40- 30
Main wash Rinses Spin red./ Super Quick, Extra rinse Long spin at the maximum speed Prewash, Main wash Rinses Spin red./ Super Quick, Extra rinse Long spin at the maximum speed Prewash, Main wash Rinses, Spin red./ Super Quick, Extra rinse Long spin at the maximum speed Prewash, Main wash Rinses Spin red./ Super Quick, Extra rinse Long spin at the maximum speed Main wash Spin red./ Rinses Super Quick, Extra rinse Short spin at 900 rpm Main wash Rinses Short spin at 900 rpm

Cotton 90 + Prewash

Cotton 60 + Prewash

Cotton 40 + Prewash

Synthetics 60 - 40 - 30
Synthetic or mixed fabrics,

Synthetics Easy iron 40

Synthetic or mixed fabrics to be gentle washed and spun.

Spin red./ Extra rinse

Programme/ Temperature Type of laundry Delicate fabrics, for example curtains. Options Description of programme

Delicates 40 - 30

Main wash Spin red./ Rinses Super Quick, Extra rinse Short spin at 700 rpm Main wash Rinses Short spin at 1000 rpm Main Wash Rinses Long spin at 1000 rpm Prewash, Main wash Rinses Short spin at 900 rpm 3 rinses Long spin at the maximum speed
Handwash Special programme for 40 - 30 - Cold hand washing fabrics Jeans 40
Special programme for jeans or dark colours cotton items

Spin red./

Spin red./ Spin red./
Sport Intensive Special programme for sport items heavily soiled 40 Rinses
Separate rinse cycle for hand washed cotton items. For emptying out the last rinse water in programmes with the Rinse Hold option. Separate spin for cottons.

Draining of water

Spin red.
Drain and long spin at the maximum speed
To interrupt a running programme, to cancel an incorrect option selection or to switch the machine off, Sport Intensive..2.5 kg Max load with Super Quick option : Cotton + Super Quick..3 kg Synthetics + Super Quick. 2 kg Delicates + Super Quick..2 kg
Max load for: Cottons..6 kg Synthetics..3 kg Delicates..3 kg Synthetics Easy Iron..1 kg Handwash..2 kg Jeans...3 kg 10

Programme information

Eco programme This programme can be selected for slightly or normally soiled cotton items. The temperature will decrease and the washing time will be extended. This allows to obtain a good washing efficiency by saving energy. Washing programme for machine washable wool as well as for hand washable woollens and delicate fabrics with the hand washing care symbol. With this programme it is possible to wash free time items as pants, shirts or jackets in Jeans and also jersey made of hi-tech materials. Some extra rinses will be carried out by the machine. Selecting this programme, the laundry is gently washed and spun to avoid any creasing. In this way ironing is easier. Furthermore the machine will perform additional rinses. This programme is suitable for washing heavily soiled sport items. The machine will add automatically a prewash phase before the main wash to eliminate mud stains. The washing temperature is 40C. The maximum spin speed is 900 rpm. We recommend you NOT to put detergent in the compartment marked by the symbol With this programme it is possible to rinse and spin cotton garments which have been washed by hand. The machine performs 3 rinses, followed by a final spin at maximum speed. The spin speed can be reduced by depressing Spin button. For emptying out the water of the last rinse in programmes with the Rinse Hold option. Turn first the programme selector dial to O, then select programme Drain and depress the Start/Pause button. Separate spin for hand washed garments and after programmes with Rinse Hold option. Before selecting this programme the selector dial must be turned to O. You can choose the speed by means of the relevant button to adapt it to the fabrics to be spun. To reset a programme and to switch off the machine turn the selector dial to O. Now can a new programme be selected.

Follow the product manufacturers instructions on quantities to use.
Degrees of water hardness
Follow the product manufacturers instructions on quantities to use. Use less detergent if: you are washing a small load, the laundry is lightly soiled, large amounts of foam form during washing.
Degrees Level Characteristic soft medium hard very hard German dH 0-7 8-14 15-21 > 21 French T.H. 0-15 16-25 26-37 > 37
Quantity of detergent to be used
The type and quantity of detergent will depend on the type of fabric, load size, degree of soiling and hardness of the water used. Water hardness is classified in so-called degrees of hardness. Information on hardness of the water in your area can be obtained from the relevant water supply company, or from your local authority. 14

Before the first use

WARNING! Ensure that the electrical and water connections comply with the installation instructions. IMPORTANT! Remove the polystyrene block and any material from the drum. IMPORTANT! Pour 2 litres of water into the main wash compartment of the detergent drawer in order to activate the ECO valve. Then run a cotton cycle at 90C, without any laundry in the machine, to remove any manufacturing residue from the drum and tub. Pour 1/2 a measure of detergent into the dispenser drawer and start the machine. Child safety lock This device permits you to leave the appliance unsupervised without having the worry that children might be injured by or cause damage to the appliance. This function remains able also when the washer-dryer is not working. There are two different ways to set this option: before pressing the button 8: it will be impossible to start the machine. after pressing the button 8 it will be impossible to change any other programme or option. To enable (disable) this option press simoultaneously for about 6 seconds 2 and 3 buttons until the icon appears (disappears) on (from) the display. Acoustic signals The machine is provided of an acoustic device, which sounds in the following cases: at the end of the cycle in the event of operating problems By pressing the 4 and 5 buttons simultaneously for about 6 seconds, the acoustic signal is deactivated (except for the events of operating problems). By pressing these 2 buttons again, the the acoustic signal is reactivated.
Operating sequence Washing
1. Load the laundry Open the door by carefully pulling the door handle outwards. Place the laundry in the drum, one item at a time, shaking them out as much as 2. Measure out the detergent and the fabric softener

possible. Close the door.
Pull out the dispenser drawer until it stops. Measure out the amount of detergent required, 15
pour it into the main wash compartment and, if you wish to carry out a programme with the prewash phase, pour it into the compartment marked. If required, pour fabric softener into the compartment marked (the amount used must not exceed the MAX mark in the drawer). Close the drawer gently. Select the required programme by means ofthe programme selector dial (1) Turn the programme selector dial to the required programme. The green light of button 8 starts to flash. It can be turned either clockwise or anticlockwise. On position O the programme is reset and the machine is switched OFF. At the end of the programme the selector dial must be turned to position O, to switch the machine off. IMPORTANT! If you turn the programme selector dial to another programme when the machine is working, the red light will of the button 8 flashes 3 times and the message Err is displayed on the display to indicate a wrong selection. The machine will not perform the new selected programme. Select the spin speed or the Rinse Hold option by pressing button 2 The relevant light will light up. When selecting a programme, the light corresponding to the maximum speed allowed for that programme will illuminate (refer to the section Programme table for the maximum allowed spin speed). Select the degree of dryness or the duration of the drying cycle by means of buttons 3 and 4 The relevant light illuminates. By depressing the button 3 it is possible to 16
select the degrees of dryness for cotton or synthetics items. The washer dryer will automatically adjust the duration of the drying cycle to the selected degree. Also the button 4 allows you to select a drying time for Cottons and Synthetics from 10 minutes to 130 minutes (2.10). Every time you press this button the time increases by 5 mins. Note! The programme time will automatically increase by up to 2 minutes. This is quite normal. Select the desired option by means of buttons 5 and 6 Depending on the programme, different functions can be combined. These must be selected after choosing the desired programme and before depressing the button 8. The corrisponding light illuminates. For more information about the compatibility of the options with the washing programmes, refer to the section Programmes table. Select the delayed start by pressing the button 10 Depress button this button to select the required delay. The selected delay time value will appear on the display for few seconds, then the duration of the programme will appear again. You must select this option after you have set the programme and before you press the button 8. You can cancel the delay time at any moment, before you press button 8. If you have already pressed it, and you wish to cancel the delay time, proceed as follows: set the washing machine to PAUSE by pressing button 8; press the button 10 once. On the display will appear the symbol 0. press button 8 again to start the programme.

(Pay attention to the water level and temperature!). After this procedure, it will be necessary to set the programme and the options again and then to depress button 8. At the end of the programme The washer dryer stops automatically. Some acustic signals sound and on the display will appear a flashing 0. The button 8 light and the light 9 go off. The door can be opened. If, at the end of a programme, there is water in the tub (light 9 still on), to empty out the water follow the following instructions: To empty out the water: 1. turn the programme selector dial to O 2. select the Drainor Spin programme 3. reduce the spin speed, if needed, by means of the button 2 4. depress button 8 5. at the end of the programme, the display shows a flashing zero 0, the light 9 goes off and it will be possible to open the door. Turn the programme selector dial to O to switch the machine off. Remove the laundry from the drum and carefully check that the drum is empty. If you do not intend to carry out another wash, close the water tap. Leave the door open to prevent the formation of mildew and unpleasant smells.

Drying only

The max load to dry in your washer -dryer is 3 kg for cotton and 2 kg for synthetics. The water tap must be open and the drain hose must be positioned in the sink or connected to the drain pipe. 1. Load the laundry. 2. Turn the selector dial to Cotton or Synthetics programme in the Drying sector. 3. For the automatic drying, Store dry (only for synthetics) or Iron dry, depress the button 3 until the light corresponding to the desired dryness degree for synthetics or cotton illuminates. 4. For the timed drying, depress the button 4 until the time you want appears on the display (see the drying programmes). 5. Press the button 8 to start the programme. 6. At the end of the programme, the buzzer sounds. A flashing zero 0 will appear on the display. At this point, begins the anti-crease phase which lasts for about 10 minutes. During this time the anti-crease phase simbol appears on the display and the door cannot be opened. Note! If you whish to open the door before or during the anti-crease phase or to interrupt it, press any button or turn the programme selector dial to any programme position (except O), the door can be immediately opened. 7. Turn the selector dial to the O position to switch the machine off. Remove the laundry.

Emergency emptying out If the water is not discharged, proceed as follows to empty out the machine: pull out the plug from the power socket; close the water tap; if necessary, wait until the water has cooled down; open the pump door using the suitable tool; place a bowl with a small edge close to the pump to collect any spillage. Remove the emergency emptying cap from the filter cover. The water should drain by gravity into the bowl. When the bowl is full, put the cap back on filter cover. Empty the bowl. Repeat the procedure until water stops flowing out; clean the pump if necessary as previously described; replace the filter into the pump and screw it firmly as previously described; replace the emergency emptying cap into the filter cover and close the pump door.

Something not working

IMPORTANT! Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below. During machine operation it is possible that the red pilot light of the button 8 flashes, the buzzer sounds and one of the following alarm codes appears on the display to indicate that the machine is not working. E10: problem with the water supply E20: problem with water draining E40: door open. Once the problem has been eliminated, press the button 8 to restart the programme. If after all checks, the problem persists, contact your local Service Centre. Malfunction Possible Cause / Solution The door has not been closed. E40 Close firmly the door. The plug is not properly inserted in the power socket. Insert the plug into the power socket. There is no power at the socket. Please check your domestic electrical installation. The main fuse has blown. Replace the fuse. The selector dial is not correctly positioned and the button 8 has not been depressed. Please turn the selector dial and press the button 8 again. The Child Safety Lock or the Delay start function option has been selected. Disable the Child Safety Lock or the Delay start function. The water tap is closed. E10 Open the water tap. The machine does not fill: The inlet hose is squashed or kinked. E10 Check the inlet hose connection. The filter in the inlet hose is blocked. E10 Clean the water inlet hose filter. The door is not properly closed. E40 Close firmly the door. 24
The washer-dryer does not start:
Malfunction The machine fills then empties immediately:

Possible Cause / Solution The end of the drain hose is too low. Refer to relevant paragraph in water drainage section. The drain hose is squashed or kinked. E20 Check the drain hose connection.
The machine does not empty and/or does not spin:
The drain pump is clogged. E20 Clean the drain pump. The option has been selected. Select the Drain or Spin programmes The laundry is not evenly distributed in the drum. Redistribute the laundry. Too much detergent or unsuitable detergent (creates too much foam) has been used. Reduce the detergent quantity or use another one. Check whether there are any leaks from one of the inlet hose fittings. It is not always easy to see this as the water runs down the hose; check to see if it is damp. Check the water inlet hose connection. The inlet hose is damaged. Change it with a new one. The cap on the emergency emptying hose has not been replaced after cleaning the pump. Put the cap back on the emergency emptying and place the latter back in its seat. Too little detergent or unsuitable detergent has been used. Increase the detergent quantity or use another one. Stubborn stains have not been treated prior to washing. Use commercial products to treat the stubborn stains. The correct temperature was not selected. Check if you have selected the correct temperature. Excessive laundry load. Introduce into the drum less laundry. 25
There is water on the floor:
Unsatisfactory washing results:

Malfunction

Possible Cause / Solution The programme is still running. Wait the end of washing cycle.

The door will not open:

The door lock has not been released. Wait untill the light 9 has gone off. There is water in the drum. Select drain or spin programme to empty out the water. The transit bolts and packing have not been removed. Check the correct installation of the appliance.
The machine vibrates or is noisy:
The support feet have not been adjusted. Check the correct levelling of the appliance. The laundry is not evenly distributed in the drum. Redistribute the laundry. Maybe there is very little laundry in the drum. Load more laundry. The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen several times before the unbalance disappears and normal spinning can resume. If, after 10 minutes, the laundry is still not evenly distributed in the drum, the machine will not spin. In this case, redistribute the load manually and select the spin programme. Redistribute the laundry.
Spinning starts late or the machine does not spin:

Water drainage The end of the drain hose can be positioned in three ways: Hooked over the edge of a sink using the plastic hose guide supplied with the machine. In this case, make sure the end cannot come unhooked when the machine is emptying. This could be done by tying it to the tap with a piece of string or attaching it to the wall.
In a sink drain pipe branch. This branch must be above the trap so that the bend is at least 60 cm above the ground. Directly into a drain pipe at a height of not less than 60 cm and not more than 90 cm. The end of the drain hose must always be ventilated, i.e. the inside diameter of the drain pipe must be larger than the outside diameter of the drain hose. The drain hose must not be kinked.
Important! Before connecting the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. Electrical connection This machine is designed to operate on a 220230 V, single-phase, 50 Hz supply. Check that your domestic electrical installation can take the maximum load required (2.2 kW), also taking into account any other appliances in use. Attention! Connect the machine to an earthed socket. The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precaution.
Attention! Should the appliance power supply cable need to be replaced, this MUST be carried out by our Service Centre. NOTE Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown. Permanent connection In the case of permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply (mains), with a minimum gap of 3mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations. The switch must not break the yellow and green earth cable at any point.

Fitting under a counter

WARNING! Before any work to the appliance, you must disconnect the plug from the power socket. Important! For safety reasons, it is dangerous to fit the appliance under a counter without the steel plate, which you can order in your nearest Service Force Centre. The top must be fixed to the cabinet as follows: Unscrew the screws from the back panel of the appliance. Push the worktop to the back and raise it to remove. (see the picture below).

820 600

Environmental concerns
Packaging materials The materials marked with the symbol are recyclable. >PE<=polyethylene >PS<=polystyrene >PP<=polypropylene This means that they can be recycled by disposing of them properly in appropriate collection containers. Old machine Use authorised disposal sites for your old appliance. Help to keep your country tidy! The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Ecological hints To save water, energy and to help protect the environment, we recommend that you follow these tips: Normally soiled laundry may be washed without prewashing in order to save detergent, water and time (the environment is protected too!). The machine works more economically if it is fully loaded. With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed at a lower temperature. Measure out detergent according to the water hardness, the degree of soiling and the quantity of laundry being washed.

Guarantee

European guarantee This appliance is guaranteed by Electrolux, in each of the countries listed in the following page, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of these countries the appliance guarantee will move with you subject to the following qualifications:
The appliance is installed in accordance with all relevant regulations in force within your new country of residence.
The provisions of this European Guarantee do not affect any of the rights granted to you by law.
The appliance guarantee starts from the date you first purchased the appliance which will be evidenced by production of a valid purchase document issued by seller of the appliance. The appliance guarantee is for the same period and to the same extent for labour and parts as exists in your country of residence for this particular model or range of appliances. The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred to another user. The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within the home, i.e. is not used for commercial purposes.