This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003.
Read and understand all warnings and cautions before using this product.

WARNING

Using batteries improperly can cause them to leak harmful solutions, overheat, or explode which may damage property or cause personal injury. Do not ignore the following warnings. Only use the batteries specified in this instruction manual. Do not install the batteries with the polarity (+/) reversed. Do not use batteries which show wear or damage. Do not expose batteries to fire, high temperatures, water, or moisture. Do not attempt to short or disassemble batteries. Do not store batteries near or in metallic products. Do not mix batteries of different types, brands, or ages. Do not use leaking batteries. If fluid from the batteries enters your eye, immediately rinse the eye with plenty of fresh water and contact a doctor. If fluid from the batteries makes contact with your skin or clothing, wash the area thoroughly with water. Tape over lithium battery contacts to avoid short-circuiting during disposal; always follow local regulations for battery disposal. Do not disassemble this product. Electric shock may cause injury if a high voltage circuit inside the product is touched. Take the product to a Minolta Service Facility when repairs are required.
This mark on the bottom of your camera is there to inform you that this camera meets the requirements of the EU (European Union) concerning interference causing equipment regulations. CE stands for Conformit Europenne (European Conformity).

Page 8

Immediately remove the batteries and discontinue use if the camera is dropped or subjected to an impact in which the interior, especially the flash unit, is exposed. The flash has a high voltage circuit which may cause an electric shock resulting in injury. The continued use of a damaged product or part may cause injuries. Keep batteries or small parts that could be swallowed away from infants. Contact a doctor immediately if an object is swallowed. Store this product out of reach of children. Be careful when around children, not to harm them with the product or parts. Do not fire the flash directly into the eyes. It may damage eyesight. Do not fire the flash at vehicle operators. It may cause a distraction or temporary blindness which may lead to an accident. Do not look at the sun or strong light sources directly through the viewfinder or lens. It may damage your eyesight or cause blindness. Do not use the product near inflammable gases or liquids such as gasoline, benzine, or paint thinner. Do not use inflammable products such as alcohol, benzine, or paint thinner to clean the product. The use of inflammable cleaners and solvents may cause an explosion or fire. If the product emits a strange odor, heat, or smoke, discontinue use. Immediately remove the batteries taking care not to burn yourself. The continued use of a damaged product or part may cause injuries. Take the product to a Minolta Service Facility when repairs are required.

CAUTION

Do not point the product directly at the sun. If sunlight is focused on an inflammable surface, a fire may result. Replace the lens cap when the product is not in use. Do not use or store the product in a hot or humid environment such as the glove compartment or trunk of a car. It may damage the product and batteries which may result in burns or injuries caused by heat, fire, explosion, or leaking battery fluid. If batteries are leaking, discontinue use of the product. Do not fire the flash while it is in contact with people or objects. The flash unit discharges a large amount of energy which may cause burns. Do not apply pressure to the data panel. A damaged panel may cause injury, and the liquid from the panel may cause inflammation. If liquid from the panel makes contact with skin wash the area with fresh water. If liquid from the panel comes in contact with the eyes, immediately rinse the eyes with plenty of water and contact a doctor.

Page 10

QUICK OPERATION

Insert batteries.

This camera uses two CR2 lithium batteries. p.18

Set full-auto operation.

Press the program-reset button to set the camera to fully automatic operation. p.30

Attach the lens.

Align the red mounting index on the lens with the one on the camera. Carefully insert the lens into the mount and turn it clockwise until it clicks into the locked position. p.20

Center your subject in the wide focus frame. If using a zoom lens, rotate the zooming ring to frame your subject as desired.
Slide the main switch to ON.
With the eye-start on, the camera will focus and set exposure automatically. Eye start is initially on when the camera is taken out of the package. With the eye-start off, the camera will focus and set exposure automatically when the shutter release button is pressed partway down.
The audio signal confirms the camera has focused when the shutter release button is pressed partway down.

Load the film.

Align the film tip with the red mark, then close the back cover.
When or appears in the viewfinder, press the shutterrelease button all the way down to take the picture.
Use focus lock if your subject is offcenter and outside the focus frame.

Page 12

NAMES OF PARTS
For information on specific parts, refer to the page shown in parentheses. Built-in flash* (35) Flash-mode button (37) Program-reset button (30) Control dial Shutter-release button (26) Self-timer lamp / Remote-control receiver1 (46/49) Function button Function dial Viewfinder* Strap eyelet (17) Eyepiece sensors* (27) Drive-mode button (46-50) Subject-program button (40-45) *This camera is a sophisticated optical instrument. Care should be taken to keep these surfaces clean. Please read the care and storage instructions in the back of this manual (p. 122). Main switch (30) Accessory shoe Data panel
Eyepiece Cup (119) Strap eyelet (17)
Grip sensors (27) Lens contacts* Focus-mode switch (75) Mirror* Lens mount Depth-of-field preview button (58) Exposurecompensation button (84) Lens release (20) Film window (23)
Remote-control terminal1 (49)
Spot-AE lock button (78) Film-chamber lock indicator (23) Manualrewind button (24) Back-cover release (21) Spot AF button (69) APPENDIX

Date button (103)

Select button (103)
Battery-chamber door (18)

Tripod socket

Available on the remote-control model only. Available on the quartz-data model only.

Page 14

NAMES OF PARTS Data Panel Viewfinder
Spot focus area (69) Manual-focus indicator (75) Shutter speed/ISO display Date indicator2 (103) Subject-program icons (40-45) Subject-program indicators (40-45) Aperture/Exposure-compensation/Custom-function display (84/106) Battery condition indicator (23) Exposure-compensation indicator (84) Wireless/Remote flash indicator (98) Frame counter/ Multiple-exposure/ Custom setting display (23/90/106) Film-transport signals (23) Cartridge mark (23) AF-mode indicators (72-74) Remote-control indicator1 (49) High-speed sync indicator (97) Wide focus frame (68) Spot metering area (78) Local focus areas (70)
Exposure-mode indicator (54-66) ExposureSelf-timer bracketing indicator (46) indicator (87)
Multipleexposure indicator (90) High-speed sync indicator (97) Flash-mode indicators (37) Wireless/Remote flash indicaRed-eye reductor (98) tion indicator (38) Single frame/Continuous advance indicator (48)
Shutterspeed/ISO display Aperture/Exposure-compensation display (85)

Flash indicator (35)

Focus signals (32)
Spot-AE lock indicator (78)

Ev scale (62/80)

Focus-area indicators (68)
Exposure-compensation indicator (85)
Available on the remote-control model only. Available on the quartz-date model only.

Page 16

This section provides the information necessary to prepare the camera for use. Strap (p.17)

Attaching the Strap

Pass the strap through the strap eyelet from below as shown.
Attach the strap so that the tip comes inside.
Push down the buckle to fix the strap.

Batteries (p.18)

Film (p.21)

Lens (p.20)

Take care not to catch the strap when closing the back cover.

Using the Eyepiece Cap

The eyepiece cap is used to prevent light from entering the camera during time exposures (buLb, p. 81) or when using the self-timer (p. 46). Light entering through the viewfinder can affect the metered exposure.
Firmly press the eyepiece cap of the strap into the eyepiece.

Page 18

Installing the Batteries
Your camera uses two 3V CR2 lithimum batteries to supply power for all camera operations.
Battery Condition Indicators
Battery condition indicators shows the level of battery power.

Slide the battery-chamber release as shown, and open the door.
Turn the main switch to ON.
A battery icon appears on the data
panel indicating the power status of the batteries. For owners of the quartz-date model, the date settings will blink if not set. Set the date settings (p.103) or press the program-reset button to display the power status.
Insert the batteries. Match the positive terminal mark inside the battery chamber-door with the positive end of the batteries.

Steady

Power is sufficient for all camera operations.

Blinks

Power is low. All functions are operational, but
the batteries will need to be replaced soon. Flash recycling time may be slow.
Close the battery-chamber door and push until it clicks.
Blinks ( no other displays appear )
Power is insufficient for camera operation and
the shutter is locked. Replace the batteries.
The battery-chamber door is closed without
When changing batteries, make sure the main switch is off. Setting the camera down with the battery-chamber door open may damage the camera. For owners of the quartz-data model, the date and time will be reset if batteries are removed for more than 5 minutes or the camera is stored with weak batteries for long periods. To set the data and time, see page 103. Read FOR PROPER AND SAFE USE (p.7) before using batteries.
the batteries inserted. The display will disappear after 5 minutes. If the data panel is blank, the batteries may be dead or installed incorrectly. Occasionally, the battery-condition indicator will give a false low-batterypower warning , even though there is enough power capacity. Turn the main switch on and off a few times to reset the display.

BATTERIES

Page 20

Attaching the Lens

This camera uses interchangeable lenses. See page 116 for information on which lenses are compatible with this camera.
Always load or remove the film under subdued light to reduce the chances of fogging.

Loading the Film

The camera automatically sets the correct film speed (ISO) with DX-code film.
Remove the body and rear lens caps.
Align the red mounting index on the lens and camera body. Carefully insert the lens into the mount, then turn it clockwise until it clicks into the locked position.

Do not insert the lens at an angle.
Press the back-cover release to open the back cover.
Insert the film cartridge into the film chamber.

Removing the Lens

While pressing the lens release, turn the lens counter-clockwise until it stops. Carefully remove the lens.
Replace the caps on the lens and attach the body cap or another lens on the camera. Do not use Polaroid Instant 35mm film. Winding problems may occur. Do not use infrared film in this camera. The cameras frame counter sensor will fog infrared film. If non-DX-coded film is used, the camera will use the previous rolls ISO setting. Refer to page 86 to set the film speed manually. More than 40 exposures can not be taken on one roll with this camera. When using 72-exposure film, the camera will start to rewind the film after 40 exposures have been made. Continued on next page
Never force the lens. If it does not fit, check its orientation with the index marks. When removing, make sure the lens release is pressed all the way down. Do not touch the inside of the camera, especially the lens contacts and mirror.

Page 22

Extend the leader between the guide rails to the index mark.
Hold the film cartridge down so that the film lays flat. If the film tip extends beyond the index mark, take the cartridge out and rewind the excess film back into the cartridge.
When the film is loaded correctly : appears in the frame counter. The film speed (ISO) is displayed on the data panel for 5 seconds. If the film is loaded with the power off, the film speed (ISO) and appears on the data panel for approximately five seconds to indicate successful loading, then the camera shuts down. When the film is loaded incorrectly : blinks in the frame counter and the shutter locks. Open the back cover and repeat steps 2 4. If the film is loaded with the power off, blinks on the data panel before the camera shuts down.
The shutter curtains precision design makes it extremely sensitive to pressure. Never touch it with your fingers or the film tip.

Film-chamber Lock

Once the film is loaded, the back-cover release will lock until the film is rewound to prevent the camera from being opened accidentally.

Close the back cover.

The camera automatically advances the film to the first frame. Take care not to catch the strap when closing the back cover.
The film window and the filmchamber lock indicator will show if a roll of film is in the camera. Always check these before loading a new film.
When film is loaded properly, the film chamber lock indicator is red, and the back cover cannot be opened. To change a roll of film in the camera, refer to manual rewind on page 24.
Film Window Film-chamber lock indicator

Page 24

FILM Rewinding the Film
After you have exposed the last frame, the camera will automatically rewind the film.

Wait until the film is completely rewound.
will appear and will blink on the data panel, indicating it is safe to open the back-cover. The film-chamber lock indicator is blank after the film is rewound.
Use full-auto when you are just starting out or when shooting under conditions that would require you to constantly adjust the focus or exposure.
Press the back-cover release to open the back cover and remove the film, then close the back cover.
Program-reset button (p.30)
Do not turn the focusing ring when the film is rewinding. Although more pictures than specified on the film package may be taken,
the film processor may not print more than the number specified on the film cartridge.

Manual Rewind

Use manual rewind to rewind the film before the roll is finished.
Gently press the manualrewind button using a pen.
Only use blunt objects. Sharp objects may damage the camera. will appear and will blink on the data panel when the film has rewound. Custom Function Notes
Cust-2: Automatic (1) or manually initiated (2) rewind start (p.108). Cust-3: Rewind the leader into the cartridge (1) or leave the leader out (2) (p.109).

Page 26

HANDLING THE CAMERA
Pressing the Shutter-release Button
Press the shutter-release button partway down to activate the cameras autofocus and auto-exposure systems when eye-start is off. Press the shutter-release button all the way down to take the picture. When taking a picture, press the shutter-release button with your index finger gently so not the shake the camera during the exposure.

EYE-START

Instead the shutter-release button, the eye-start automatically activates the cameras focus and exposure systems when you bring the camera to your eye. The eye-start is initially on.

Turning Eye-start ON

Turn the function dial to

Before pressing

Pressing partway down activates camera systems
Pressing all the down releases the shutter
While pressing the function button, turn the control dial until appears on the data panel. The eye-start function is now on.

Holding the Camera

Grip the camera firmly with your right hand, while supporting the lens with your left. Keep your elbows at your side and your feet shoulderwidth apart to hold the camera steady. Keep the camera strap around your neck or wrist in the event you accidentally drop the camera.

Grip Sensor

When taking a picture, touch the grip sensor to activate the eyepiece sensors located near the viewfinder. Bring the camera to your eye and frame the subject in the viewfinder. When an object is detected near the viewfinder, the cameras systems are activated to set the focus and exposure.
Autofocus and exposure systems shut down approximately five seconds after eyepiece or grip sensor contact is broken.

Lean against a wall or rest your elbows on a solid surface to steady the camera in low-light situations. The use of the tripod is recommended when using the camera in low-light situations or with slow shutter speeds or telephoto lenses.

Eyepiece sensors

Page 28
EYE-START Canceling Eye-start

AUDIO SIGNAL

While pressing the function button, turn the control dial until appears on the data panel.
Canceling the Audio Signal
While pressing the function button, turn the control dial to.
Turning the Audio Signal On
Eye-start may not work properly when using a tripod, wearing gloves, or if your hands are very dry. In these cases, press the shutter-release button partway down to activate the autofocus and metering systems. Infrared absorbing sunglasses may affect eye-start operation. Custom Function Notes Cust-7 : The grip sensor activates the eyepiece sensors (1), the main switch activates the eyepiece sensors (2) (p.110).
Turn the function dial to While pressing the function button, turn the control dial until appears on the data panel.
Audio signal is initially on. The camera will produce an audio tone when : focus is confirmed. 2 short beeps (Continuous AF (p. 73) does not use audio signals.) during the self-timer countdown. will beep in unison with the self-timer lamp. Remote-control operation* will give one short beep before the shutter releases with the release button. With the delayed-release button, the signal will beep rapidly for 1 second, and then sound a long tone just before the shutter releases. *Remote-control is sold separately for owners of the remote-control model.

Page 30

TAKING PICTURES IN FULL-AUTO
Full-auto is the cameras standard operating mode and is suited for use in almost any situation. When selected, the camera sets the focus and exposure automatically and fires the built-in flash when necessary.
With the eye-start on, the camera will focus and set exposure automatically. With the eye-start off, press the shutter release button partway down to activate the autofocus and exposure systems.
When appeas in the viewfinder, the flash will fire (p.35).

Flash signal

Press the program-reset button set the camera to full-auto.
The camera will return to its default settings (p115).
When or appears in the viewfinder, press the shutter-release button all the way down to take the picture.

The audio signal confirms the camera has focused when the shutter-release button is pressed partway down. In low-light conditions, the AF illuminator will activate to determine focus distance (p.76).

Page 32

Focus Signals
The following signals appear in the viewfinder to indicate the focus status. Focusing time can be longer with macro or telephoto lenses. In very dark conditions the camera may require a little more time to ensure accurate focus.

Special Focus Situations

The camera may not be able to focus in the situations described below. Use focus lock (p. 34) or manual focus (p.75). AUTOMATIC OPERATION If the subject within the focus frame is very bright, or low in contrast. If two subjects at different distances overlap in the focus frame. If a subject composed of alternating light and dark lines completely fills the focus frame. If your subject is near a very bright object or area.
Steady Steady Steady Blinking
Focus is confirmed. Focus is confirmed (Continuous AF ). Lens is focusing (Continuous AF). The shutter is locked. Focus cannot be confirmed. The shutter is locked.
When focus cannot be confirmed, the subject may be too close or one of the special focus situations on the following page is preventing the system from focusing. Use focus lock (p. 34) or manual focus (p. 75). Custom Function Notes
Cust-1: Autofocus has priority (1), shutter-release has priority (2) (p.108).

Page 34

FOCUS LOCK
The focus-lock function is used when the subject is off-center and outside the focus frame. Focus lock may also be used when a special focusing situation prevents the camera from focusing on the subject. Focus lock cannot be used with continuous AF. The spot AF button (p.69) can also be used for focus lock. Focus can be locked in continuous AF (p.73) with the spot AF button.

USING THE BUILT-IN FLASH

When appears in the viewfinder in full-auto, the built-in flash pops-up automatically when the shutter-release button is pressed partway down. Once the flash is up, it will fire when necessary. The shutter will not release until the flash is charged. To turn off the autoflash, select flash cancel. Pressing the program-reset button resets the flash to autoflash mode. Push down the built-in flash when the camera is not in use.

Flash Cancel

Use the flash cancel when photographing twilight scenes or to capture the ambiance of the existing light.

built-in flash.

Lens Shadowing
Lens shadowing occurs when the lens or lens hood blocks part of the output from the built-in flash. Lens shadowing appears as a semi-circular shadow area at the bottom (horizontal pictures) or side (vertical pictures) of the image.
Remove the lens hood before using the built-in flash. Lens shadowing may occur with the following lenses at the shorter focal lengths. AF Zoom 28-70mm f/2.8G AF Zoom 17-35mm f/3.5G AF Zoom 28-135mm f/4.0-4.5 AF Zoom 28-85mm f/3.5-4.5 The built-in flash can not be used with the following lenses: AF 300mm f/2.8 (APO tele) AF 600mm f/4.0 (APO tele)
The flash will not fire even if the built-in flash pops-up.
To return to autoflash mode, repeat the step above until appears. The shutter speeds will be slow in low-light situations. The use of a tripod
is recommended. Custom Function Notes
Cust-8: Autoflash will be set in P mode (1), flash cancel will be set in PA mode (2) or PS mode (3) (p.111).

Page 38

USING THE BUILT-IN FLASH Red-Eye Reduction
When using flash in low-light conditions, light reflecting from the retina of your subjects eyes may produce the effect known as red-eye. Use the built-in flashs red-eye reduction mode to produce natural looking photographs.
Now that you are comfortable with the operation of the camera, take more control of the creative process by telling the camera what kind of pictures you want to take. The subject-program modes optimize camera settings for specific situations. This section also lets you explore the use of the drive-mode button. Drive modes control the advance of the film.
While pressing the function button, turn the control dial until and appear on the data panel.
When you release the button, the display will return to normal and only will remain on the data panel. Warn your subject that the flash will fire a few short flash bursts just before the picture is taken.

Subject-program button

Drive-mode button
Canceling Red-eye Reduction
Turn the function dial to. While pressing the function button, turn the control dial until appear on and the data panel.

Page 40

SUBJECT-PROGRAM SELECTION

Portrait

Portraits have the greatest impact when a shallow depth-of-field* is used to separate the subject from the background. In portrait mode, the necessary settings are made automatically, leaving you free to capture the perfect expression. *Depth-of-field is the area in front of and behind the subject that appears sharp (p. 52).

Landscape

Landscape photography requires a large depth-of-field to make sure the subject and background are in focus. In landscape mode, the camera is set to obtain the greatest depth-of-field possible, while maintaining a shutter speed fast enough to prevent blurring from camera shake. SUBJECT / DRIVE
Press the subject-program button until the subjectprogram indicator points to.
For best results use the telephoto setting of the lens. Use fill flash (p. 37) when your subject is backlit or has strong shadows across the face. Focus on your subjects eyes and be ready to capture the perfect expression. Use night portrait mode (p.44) with subjects at night.
For best results zoom to a wide angle setting or use a wide angle lens. Include a foreground subject or detail to create a feeling of depth in the picture. Use flash when a subject in the foreground is backlit or has strong shadows across the face. Without a foreground subject, the flash will have no effect on the landscape. Please see page 36 for the cameras flash range. For best results, use a tripod. Use night portrait mode (p.44) with subjects or scenery at night.

Page 42

SUBJECT-PROGRAM SELECTION Close-up
Use close-up mode when photographing small objects like flowers or jewelry. In close-up mode, the camera automatically sets the best possible aperture and shutter speed for close-up photography. Focusing time can be longer with macro lenses.

Sports

Fast shutter speeds are needed to stop action. In sports mode, the camera will set the fastest possible shutter speed and continually adjust the focus to track fast-moving subjects.
Use a tripod to reduce camera shake.
The camera continues to focus as long as the shutter-release button is pressed partway down. Continuous AF (p.73) is used.
For best results in close-up photography use a macro lens or a macro capable zoom lens. Do not use the built-in flash if your subject is closer than 1.0m (3.3 ft.). The flash exposure will be overexposed. See flash range, p. 36. At close distances, the lens or len hood may block the flash, creating a shadow at the bottom of your image (lens shadowing, p. 36). The use of an accessory flash is recommended. Make sure the subject is not closer than the minimum focusing distance of lens. Refer to the owners manual of your lens.

The built-in flash is only effective when your subject is within the flash range. When the subject is not within the range, use flash cancel (p.37). The use of fast film is recommended. Mount the camera on a tripod or monopod when using telephoto lenses.

Page 44

SUBJECT-PROGRAM SELECTION Night Portrait
Night portraits balance the cameras flash exposure with the background exposure. In night portrait mode, the camera control the aperture and shutter speed, allowing the background to appear in the photograph.
Photograping Night Scenes
Cancel the flash in night portrait mode to photograph night scenes. The longer shutter speeds set in night portrait mode let you capture beautiful photographs of twilight scenes and night skylines.
Set the flash to fill flash or fill flash with red-eye reduction when using night portrait mode. See pages 37 and 38.

Flash-mode button

Press the subject-program button until the subject-program indicator points to.
While pressing the flashmode button, turn the control dial until appears on the data panel.
Use a tripod to reduce camera shake.

Control dial

The use of fast film is recommended. Warn your subject not to move while the picture is taken. The shutter remains open to capture the background. The shutter speed may be slow. Use a tripod to reduce camera shake.
The use of fast film is recommended. Dark night scenes may be prevent the AF system from focusing, use focus lock (p34) or manual focus (p75). Night scenes tend to be better at twillight rather than in the darkness of night. The faint light in the early evening sky adds detail to the shadows of the scene. The shutter speed may be slowe. Use a tripod to reduce camera shake.

Page 46

DRIVE MODES

Self-timer

The self-timer delays the release of the shutter for approximately 10 seconds after the shutter-release button is pressed.
Press the shutter-release button partway down to lock the focus.
For off-center subjects, use focus lock (p. 34).
Press the shutter-release button all the way down to start the timer.

Single frame advance

The self-timer lamp on the front of the camera will blink, then glow just before the shutter releases. The audio signal beeps in unison with the self-timer lamp (p.29).

Remote-control

Continuous advance
Center your subject in the focus frame.
Do not press the shutter-release button while standing in front of the camera.The focus and exposure is set when the shutter-release button is pressed. The self-timer is cancelled after the shutter is released. To cancel the self-timer countdown, press the drive-mode button or slide the main switch to OFF before the shutter releases. Attach the eyepiece cap if there is a bright light source behind the camera (p.17).
Place the camera on a tripod. Press the drive-mode button until appears on the data panel.

Page 48

DRIVE MODES Continuous Adavance
In this mode, the camera continues to release the shutter and advance the film as long as the shutter-release button is held down.
The camera takes 3 frames per second, when setting the shutter-speed to above 1/125 second with flash cancel (p.37), single-shot autofocus or manual focus (p.75), and new batteries.* * For the quartz-date model, the data-imprinting function is off (p.103).
For Owners of the Remote-control Model
The camera can be operated up to 5m (16.4 ft.) away with the IR Remote Control RC-3 (sold separatedly).
Emitter window Delay button Release button
Place the camera on a tripod. Press the drive-mode button until appears on the data panel. Arrange the camera and subject position to compose your picture. Point the emitter window toward the remote-control receiver and press the release or the delay button.
Press the drive-mode button until appears on the data panel. Press and hold the shutterrelease button to begin taking a series of pictures.
When taking flash pictures, the shutter will release only when the built-in flash finishes charging between exposures. With accessory flashes, the shutter will continue to release even if the flash is charging. With continuous AF and moving subjects, the shutter will release only when the camera has focused on the subject between exposures. To return to single frame mode, press the drive-mode button until appears on the data panel. AF zoom xi and power zoom lenses cannot be zoomed when taking pictures with continuous adavance. Custom Function Notes
Cust-1: Autofocus has priority (1), the shutter-release has priority (2) (p.108).
If the release button is pressed, the lamp on the front of the camera will blink once before the shutter releases. The audio signal will produce 1 short beep. If the delay button is pressed, the lamp on the front of the camera will blink for two seconds before the shutter releases. The audio signal will beep in unison with the lamp. The remote control may not work under fluorescent lighting or in backlit situations. If the built-in flash pops-up when the release button on remote control is pressed, wait a few seconds for the flash to charge before pressing the release button again. To save power, remote-control mode is canceled if the remote control is not operated for more than 5 minutes. Attach the eyepiece cap if there is a bright light source behind the camera.