I-45C I-45CV
Motherboard Intel Socket 775 Installation Guide
Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are the property of their respective owners. This document contains materials protected under International Copyright Laws. All rights reserved. No part of this manual may be reproduced, transmitted or transcribed without the expressed written permission of the manufacturer and authors of this manual. If you do not properly set the motherboard settings, causing the motherboard to malfunction or fail, we cannot guarantee any responsibility. For EU-member States: Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE): The use of the symbol indicates that this product may not be treated as household waste. By Ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be cause by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Best Management Practices for Perchlorate Materials: Perchlorate Material special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate/.

I-45C/I-45CV

< > < >(SJ/T11364-2006) < > / The Mark and Information are applicable for People's Republic of China only.
PCB (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE)
: SJ/T11363-2006 : SJ/T11363-2006 This information is applicable for People's Republic of China only.

Contents

1. Hardware Setup.. 1
1.1 Specifications...1 1.2 Choosing a Computer Chassis..2 1.3 Installing Motherboard..2 1.4 Checking Jumper Settings..3 1.4.1 CMOS Memory Clearing Header and Backup Battery...3 1.5 Connecting Chassis Components..4 1.5.1 ATX Power Connectors..4 1.5.2 Front Panel Switches and Indicators Headers.5 1.5.3 FAN Power Connectors..5 1.6 Installing Hardware..6 1.6.1 CPU Socket 775..6 1.6.2 DDR2 Memory Slots..8 1.7 Connecting Peripheral Devices..9 1.7.1 Floppy and IDE Disk Drive Connectors..9 1.7.2 Serial ATA Connectors..9 1.7.3 Additional USB 2.0 Port Headers..10 1.7.4 Internal Audio Connectors..10 1.7.5 Front Panel Audio Connection Header..11 1.8 PCI and PCI Express X16, X1 Slots..12 1.9 Connecting Rear Panel I/O Devices.. 12

iv I-45C/I-45CV

2. BIOS Setup.. 13 3. Driver & Utility.. 14 4. Appendix.. 15
4.1..15 4.2..16 4.3 Troubleshooting (How to Get Technical Support?).17 4.3.1 Q & A..17 4.3.2 Technical Support Form.18 4.4 Contact Information..19
1. Hardware Setup 1.1 Specifications

LGA775 socket for Intel Core 2 Duo / Pentium Dual-Core / Pentium D / Pentium 4 / Celeron D Processor with 1333*1/ 1066 / 800 / 533MHz FSB.
*1 The FSB1333 CPU will operate in over-clocking mode. Under this situation, the PCIE frequency will also be over-clocked to 115MHz.

Serial ATA

4x SATA 3.0Gb/s

Expansion Slots

1x PCI-E X16 slot 1x PCI-E X1 slot 2x PCI slots

Internal I/O Connectors

1x 1x 4x 2x 1x 1x 1x 1x 1x 1x 1x 4x 1x 1x Floppy port Ultra ATA 100 IDE connector SATA 3.0Gb/s connectors USB 2.0 headers FP-Audio header CD-In connector PS/2 Keyboard connector PS/2 Mouse connector COM port LPT port VGA connector USB 2.0 connectors RJ-45 LAN connector 5.1-Channel Audio Connector
Supports Intel Hyper-Threading Technology

Chipset

Intel 945GC / ICH7

Memory

2x 240-pin DIMM slots support up to 4GB*2 capacity Supports Dual Channel DDR2 667/533*3/400 Un-buffered Non-ECC memory
* Due to the chipset limitation, the actual memory size may be less than 4GB for the reservation of system usage under Windows XP and Windows Vista. *3 Due to the chipset limitation, the DDRmemory module runs at 500MHz with FSB1333 CPU.

Rear Panel I/O

Graphics
Integrated Intel Graphics Media Accelerator 950 (GMA950)
I-45C: Onboard GbE LAN I-45CV: Onboard 10/100 LAN
100% Lead-free process and RoHS compliant

Miscellaneous

Micro ATX form factor (244mm x 220mm) Specifications and information contained herein are subject to

change without notice.

Onboard HD 5.1 Channel Audio CODEC
1.2 Choosing a Computer Chassis
Choose a chassis big enough to install this motherboard. As some features for this motherboard are implemented by cabling connectors on the motherboard to indicators and switches or buttons on the chassis, make sure your chassis supports all the features required. If there is a possibility of adopting some more hard drives, make sure your chassis has sufficient power and space for them. Most chassis have alternatives for I/O shield located at the rear panel. Make sure the I/O shield of the chassis matches the I/O port configuration of this motherboard. You can find an I/O shield specifically designed for this motherboard in its package.

with slots. After the board has been positioned, check to make sure everything is OK before putting the chassis back on. Always power off the computer and unplug the AC power cord
before adding or removing any peripheral or component. Failing to so may cause severe damage to your motherboard and/or peripherals. Plug in the AC power cord only after you have carefully checked everything.
1.3 Installing Motherboard
Most computer chassis have a base with many mounting holes to allow the motherboard to be securely attached, and at the same time, prevent the system from short circuits. There are two ways to attach the motherboard to the chassis base: (1) with studs, or (2) with spacers. Basically, the best way to attach the board is with studs. Only if you are unable to do this should you attach the board with spacers. Line up the holes on the board with the mounting holes on the chassis. If the holes line up and there are screw holes, you can attach the board with studs. If the holes line up and there are only slots, you can only attach with spacers. Take the tip of the spacers and insert them into the slots. After doing this to all the slots, you can slide the board into position aligned 2
To install this motherboard: 1. Locate all the screw holes on the motherboard and the chassis base. 2. Place all the studs or spacers needed on the chassis base and have them tightened. 3. Face the motherboards I/O ports toward the chassiss rear panel. 4. Line up all the motherboards screw holes with those studs or spacers on the chassis. 5. Install the motherboard with screws and have them tightened. To prevent shorting the PCB circuit, please REMOVE the metal studs
or spacers if they are already fastened on the chassis base and are without mounting-holes on the motherboard to align with.
This side faces the chassiss rear panel.
1.4 Checking Jumper Settings
For a 2-pin jumper, plug the jumper cap on both pins will make it CLOSE (SHORT). Remove the jumper cap, or plug it on either pin (reserved for future use) will leave it at OPEN position.
For a 3-pin jumper, pin 1~2 or pin 2~3 can be shorted by plugging the jumper cap in.
Pin-1 and pin-2 shorted (Default): Normal operation. Pin-2 and pin-3 shorted: Clear CMOS memory.

Pin 1~2 SHORT

Pin 2~3 SHORT
1.4.1 CMOS Memory Clearing Header and Backup Battery
The time to clear the CMOS memory occurs when (a) the CMOS data becomes corrupted, (b) you forgot the supervisor or user password preset in the BIOS menu, (c) you are unable to boot-up the system because the CPU ratio/clock was incorrectly set in the BIOS menu, or (d) whenever there is modification on the CPU or memory modules. This header uses a jumper cap to clear the CMOS memory and have it reconfigured to the default values stored in BIOS. I-45C/I-45CV

To clear the CMOS memory and load in the default values: 1. Power off the system. 2. Set pin-2 and pin-3 shorted by the jumper cap. Wait for a few seconds. Set the jumper cap back to its default settings --- pin-1 and pin-2 shorted. 3. Power on the system. 4. For incorrect CPU ratio/clock settings in the BIOS, press <Del> key to enter the BIOS setup menu right after powering on system. 5. Set the CPU operating speed back to its default or an appropriate value. 6. Save and exit the BIOS setup menu. CMOS Backup Battery: An onboard battery saves the CMOS memory to keep the BIOS information stays on even after disconnected your system with power source. Nevertheless, this backup battery exhausts after some five years. Once the error message like CMOS BATTERY HAS FAILED
or CMOS checksum error displays on monitor, this backup battery is no longer functional and has to be renewed.
1.5 Connecting Chassis Components
1.5.1 ATX Power Connectors
These connectors provide the connection from an ATX power supply. As the plugs from the power supply fit in only one orientation, find the correct one and push firmly down into these connectors.
To renew the backup battery: 1. Power off the system and disconnect with AC power source. 2. Remove the exhausted battery. 3. Insert a new CR2032 or equivalent battery. Pay attention to its polarity. The + side is its positive polarity. 4. Connect AC power source and power on the system. 5. Enter the BIOS setup menu. Reconfigure the setup parameters if necessary. CAUTION: Danger of explosion may arise if the battery is incorrectly renewed. Renew only with the same or equivalent type recommended by the
battery manufacturer. instructions.
ATX 24-Pin Power Connector: The power supply with 20-pin or 24-pin cables can both be connected to this 24-pin connector. Connect from pin-1 for either type. However, a 20-pin power supply may cause the system unstable or even unbootable for the sake of insufficient electricity. A minimum power of 300W or higher is recommended. ATX 12V 4-Pin Power Connector: This connector supplies power to CPU. The system will not start without connecting power to this one.
Dispose of used batteries according to the battery manufacturers
1.5.2 Front Panel Switches and Indicators Headers

This header is used for connecting switches and LED indicators on the chassis front panel. Watch the power LED pin position and orientation. The mark + align to the pin in the figure below stands for positive polarity for the LED connection. Please pay attention when connecting these headers. A wrong orientation will only result in the LED not lighting, but a wrong connection of the switches could cause system malfunction.
PLED (Pin 16, 18, 20): Connects to the Power LED cable of chassis front panel.
1.5.3 FAN Power Connectors
These connectors each provide power to the cooling fans installed in your system. CPUFAN1: CPU Fan Power Connector SYSFAN1: System Fan Power Connector AUXFAN1: Auxiliary Fan Power Connector

on these connectors.

These fan connectors are not jumpers. DO NOT place jumper caps
HLED (Pin 1, 3): Connects to the HDD LED cable of chassis front panel. RST (Pin 5, 7): Connects to the Reset Switch cable of chassis front panel. SPKR (Pin 13, 15, 17, 19): Connects to the System Speaker cable of chassis. SLED (Pin 2, 4): Connects to the Suspend LED cable (if there is one) of chassis front panel. PWR (Pin 6, 8): Connects to the Power Switch cable of chassis front panel. 5

1.6 Installing Hardware

DO NOT scratch the motherboard when installing hardware. An
accidental scratch of a tiny surface-mount component may seriously damage the motherboard. notices: 1. A maximum 20 cycles of CPU installation is recommended. 2. Never touch the contact pins with fingers or any object. 3. Always put on the cap when the CPU is not in use.
2. Use your right-thumb to raise the load plate. Lift it up to fully open position.
In order to protect the contact pins, please pay attention to these

1.6.1 CPU Socket 775

The installation procedures vary with different types of CPU
fan-and-heatsink assembly. The one shown here is served for demo only. For detailed information on how to install the one you bought, refer to its installation guidelines.
Clear the CMOS memory after replacing CPU. 1. Place the board so that the lever-hook of the socket is on your left side. Use your left thumb and forefinger to hold the lever hook, pull it away from the retention tab. Rotate the lever to fully open position.

3. Use your right thumb and forefinger to grasp the CPU package. Be sure to grasp on the edge of the substrate, and face the Pin-1 indicator toward the bottom-left side. Aim at the socket and place the CPU package vertical down into the socket. 4. Visually inspect if the CPU is seated well into the socket. The alignment key must be located in the notch of package.
5. Use your left hand to hold the load plate, and use your right thumb to peel the cap off. The cap plays an
important role in protecting contact pins. In order to prevent bent pin, PUT ON the cap after operation or testing.
8. Place the heatsink and fan assembly onto the socket. Align the four fasteners toward the four mounting holes on the motherboard.
6. Lower the plate onto the CPU package. Engage the load lever while gently pressing down the load plate.
9. Press each of the four fasteners down into the mounting holes. Rotate the fastener clock-wise to lock the heatsink and fan assembly into position.
7. Secure the lever with the hook under retention tab.
10. Attach the four-pin power plug from the heatsink and fan assembly to the CPU FAN connector.
A higher fan speed will be helpful for better airflow and
heat-dissipation. Nevertheless, stay alert to not touch any heatsink since a high temperature generated by the working system is still possible.

1.6.2 DDR2 Memory Slots

To install system memory:
1. Power off the computer and unplug the AC power cord before installing or removing memory modules. 2. Locate the DIMM slot on the board. Install DIMMs with the same CAS latency. To reach the optimum compatibility, obtain memory modules from the same vendor.
removing memory modules, but you will have to clear the CMOS memory first if any memory module related problem occurs.
3. Hold two edges of the DIMM module carefully, keep away from touching its connectors. 4. Align the notch key on the module with the rib on the slot. 5. Firmly press the module into the slots until the ejector tabs at both sides of the slot automatically snap into the mounting notch. Do not force the DIMM module in with extra force as the DIMM module only fits in one direction. 6. To remove the DIMM modules, push the two ejector tabs on the slot outward simultaneously, and then pull out the DIMM module. Static electricity can damage the electronic components of the
computer or optional boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a grounded metal object briefly.
Usually there is no hardware or BIOS setup required after adding or

1.7 Connecting Peripheral Devices
1.7.1 Floppy and IDE Disk Drive Connectors
1.7.2 Serial ATA Connectors
Each SATA connector serves as one single channel to connect one SATA device by SATA cable.
Connect the single end at the longer length of ribbon cable to the FDD on the board, the two connectors on the other end to the floppy disk drives connector. Generally you need only one floppy disk drive in your system. The red line on the ribbon cable must be aligned with pin-1 on both
the FDD port and the floppy connector.
To connect SATA device: 1. Attach either end of the signal cable to the SATA connector on motherboard. Attach the other end to the SATA device. 2. Attach the SATA power cable to the SATA device and connect the other end from the power supply.
Connect the single end (blue connector) at the longer length of ribbon cable to the IDE port of this board, the other two ends (gray and black connector) at the shorter length of the ribbon cable to the connectors of your hard drives. Make sure to configure the Master
and Slave relation before connecting two drives by one single ribbon cable. The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and the hard-drive connector.
The motherboard in this photo is served for DEMO only, and may not
be the same type or model as the one described in this manual.
1.7.3 Additional USB 2.0 Port Headers
Each header supports 2x additional USB 2.0 ports by connecting bracket or cable to the rear I/O panel or the front-mounted USB ports of your chassis.
1.7.4 Internal Audio Connectors
This connector connects to the audio output of internal CD-ROM drive or add-on card.

Pin 5 7

Pin Assignment VCC Data0 Data0 + Ground

Pin 10

Pin Assignment VCC Data1 Data1 + Ground NC
Make sure the connecting cable bears the same pin assignment.
1.7.5 Front Panel Audio Connection Header
This header provides the front panel connection for HD (High Definition) Audio, yet for AC97 Audio CODEC connection, you must carefully check the pin assignment before connecting from the front panel module. An incorrect connection may cause malfunction or even damage the motherboard.
Please do not connect the Ground cable or USB VCC cable from
the front panel module to the Pin 4 AVCC of this header.
Driver Configuration for AC97 audio connection: The audio driver is originally configured to support HD Audio. For AC97 audio connection, you may: 1. Right-click the Realtek HD Audio Manager icon in system tray.

2. Click Audio I/O tab, and then click Connector Settings. Pin Assignment (HD AUDIO) MIC2 L AGND MIC2 R AVCC FRO-R MIC2_JD F_IO_SEN FRO-L LINE2_JD Pin Assignment (AC97 AUDIO) MIC In GND MIC Power NC Line Out (R) NC NC Line Out (L) NC 11 3. Click Disabled front panel jack detection, and then click OK to confirm.
1.8 PCI and PCI Express X16, X1 Slots
Install PCI Express X16 graphics card into slot PCIEXP1. Install PCI Express X1 cards into slot PCIE1. Install PCI cards into slots PCI1 and/or PCI2.
1.9 Connecting Rear Panel I/O Devices
The rear I/O part of this motherboard provides the following I/O ports:
Mouse: Connects to PS/2 mouse. Keyboard: Connects to PS/2 keyboard. LPT1: Connects to printer or other devices that support this communication protocol. COM1: Connects to external modem, mouse or other devices that support this communication protocol. VGA1: Connects to monitor input. AUDIO1: Line-In: Connects to the line out from external audio sources. Line-Out: Connects to the front left and front right channel. Mic-In: Connects to the plug from external microphone. USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse, keyboard, hub, digital camera, joystick etc. LAN1: Connects to Local Area Network.

2. BIOS Setup

This motherboard provides a programmable EEPROM so that you can update the BIOS utility. The BIOS (Basic Input/Output System) is a program that deals with the basic level of communication between processor and peripherals. Use the BIOS Setup program only when installing motherboard, reconfiguring system, or prompted to Run Setup. After powering up the system, the BIOS message appears on the screen, the memory count begins, and then the following message appears on the screen:
Phoenix AwardBIOS CMOS Setup Utility
Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations
PC Health Status Load Fail-Safe Defaults Load Optimized Defaults Set Password Save & Exit Setup Exit Without Saving

PRESS DEL TO ENTER SETUP

If this message disappears before you respond, restart the system by pressing <Ctrl> + <Alt> + <Del> keys, or by pressing the Reset button on computer chassis. Only when these two methods fail should you restart the system by powering it off and then back on. After pressing <Del> key, the main menu screen appears.

Esc: Quit F10: Save & Exit Setup
: Select Item (945GC-W627DHG-6A79HA1FC-00)
Time, Date, Hard Disk Type.
In order to increase system stability and performance, our
engineering staff is constantly improving the BIOS menu. The BIOS setup screens and descriptions illustrated in this manual are for your reference only, and may not completely match with what you see on your screen. function.
Do not change the BIOS parameters unless you fully understand its

3. Driver & Utility

The Driver & Utility CD that came packed with this motherboard contains drivers, utilities and software applications required for its basic and advanced features. Place the Driver & Utility CD into the CD-ROM drive in your system. The following installation auto-run screen appears. If not, browse the root directory of the CD-ROM via the File Manager, and double click the AUTORUN file. [Drivers]: Click this button to enter the driver installation menu. [Q-Install]: Click this button to install all the drivers needed for this motherboard at one stroke. For Windows XP 64-bit and Windows 2003 32-bit/64-bit installation: You may escape the rest of the driver items in this menu after having finished this installation, but for operating systems Windows XP 64-bit and Windows 2003 32-bit/64-bit, you must install the bus driver for [Microsoft High Definition Audio] first, and then install the following [Realtek HD Audio Driver] item separately to enable the audio function. For Adobe Reader V8.0 installation in systems running versions of Windows prior to Windows XP: You should have your Internet Explorer upgraded to the version later than 6.0.2600.0 before installing Adobe Reader V8.0 from the download site: http://www.microsoft.com/downloads/details.aspx?familyid=1E 1550CB-5E5D-48F5-B02B-20B602228DE6&displaylang=en [Manual]: Click this button to enter the users manual menu. [Utility]: Click this button to enter the utilities installation menu. [abit Utility]: Click to enter the installation menu of utilities exclusively developed by ABIT. [Browse CD]: Click this button to browse the contents of this Driver & Utility CD. [Close]: Click this button to exit this installation menu.

4. Appendix 4.1

1333*1/1066/800/533MHz Intel Core 2 Duo / Pentium Dual-Core / Pentium D / Pentium 4 / Celeron D

*1 FSB1333 CPU PCIE 115MHz

4 SATA 3.0Gb/s

1 PCI-E X16 1 PCI-E X1 2 PCI
Ultra ATA 100 IDE 4 SATA 3.0Gb/s 2 USB 2.FP-Audio 1 CD-In

Intel Hyper-Threading

DIMM 4GB*2 DDR2 667/533*3/400 ECC
*2 Windows XP Windows Vista 4GB *3 DDRFSB1333 CPU 500MHz
1 PS/PS/COM 1 LPT 1 VGA 4 USB 2.RJ-5.1
Intel Graphics Media Accelerator 950 (GMA950)
I-45C: GbE LAN I-45CV: 10/100 LAN

100% RoHS

5.1 HD

Micro ATX 244mm x 220mm

1333*1/1066/800/533MHz Intel Core 2 Duo / Pentium Dual-Core / Pentium D / Pentium 4 / Celeron D Intel
I-45C: GbE LAN I-45CV: 10/100M LAN

Micro ATX 244mm x 220mm

4 SATA 3.0Gb/s 16 I-45C/I-45CV
4.3 Troubleshooting (How to Get Technical Support?)

4.3.1 Q & A

Q: A: Do I need to clear the CMOS before I use a new motherboard to assemble my new computer system? Yes, we highly recommend that you clear the CMOS before installing a new motherboard. Please move the CMOS jumper from its default 1-2 position to 2-3 for a few seconds, and then back. When you boot up your system for the first time, follow the instructions in the user's manual to load the optimized defaults. If my system hangs when I update the BIOS or set the wrong CPU parameters, what should I do? Whenever you update the BIOS or if the system hangs due to wrong CPU parameters setting, always clear CMOS jumper before booting up again. Why does the system fail to boot up again right after a mechanical power-off? Please keep a 30-second interval between each mechanical power On/Off. Why does the system fail to boot up and nothing displays on the screen after I did some over-clocking or non-standard settings inside the BIOS? It should not cause hardware or permanent damage to motherboard when BIOS settings were changed from default to over-clocking or non-standard status. We suggest the following three troubleshooting methods to discharge CMOS data, recover the hardware default status, and then making the motherboard work again. There is no need to bother returning the motherboard to where you bought it from or go through an RMA process. Step 1. Switch off the power supply unit and then switch it on again after one minute. If there is no power-switch on the power supply unit, disconnect its power cord for one minute and then reconnect. Press and hold the <Insert> key on the keyboard, and press the power-on button to boot up system. If it works, release the <Insert> key and hit <Del> key to enter the BIOS setup page to apply the correct settings. If the situation remains the same, repeat the procedures in Step 1 three times, or try Step 2. Step 2. Switch off the power supply unit or disconnect the power cord. Open the chassis cover. Locate the CCMOS jumper near the button battery. Change the jumper position from default 1-2 to 2-3 for one minute to discharge the CMOS data, and then put it back to default 1-2 position. Close the chassis and switch on the power supply unit or plug in the power cord. Press the power-on button to boot up system. If it works, hit <Del> key to enter the BIOS setup page to do the correct settings. If the situation remains the same, try Step 3. Step 3. The same procedure as Step 2, but while discharging the CMOS data, pull out the ATX power connectors from motherboard and remove the button battery during CMOS discharge.

How to get a quick response for my request on technical support? Please carry out a simple troubleshooting before sending Technical Support Form: System boot-up fails after the system had been assembled: Check the motherboards supporting specifications first to see if all the key components attached in your system can meet. To do so, you may:
Remove all the unnecessary add-on devices (except the CPU, VGA card, DRAM, and Power Supply), and then reboot. If the trouble still exists, try another VGA card of different brand/model to see if the system will start. If the trouble still exists, try another memory module of different brand/model.

Q: A: Q: A: Q: A:

If the trouble still exists, try another CPU and Power Supply. If the system runs successfully, shut it down and start re-installing the interface cards and devices that were previously installed in the system. Re-install and start the system one at a time until the system wont start. Malfunction in the OS: If the system hangs after resuming from S3 or some testing program, if the CPU cannot be recognized properly, if the display resolution mixed, or if a certain program cannot be executed, etc, you may:
Check if there is any conflict in the Control Panel/System Properties. How to fill in the Technical Support Form? To fill in this Technical Support Form, please refer to the following instructions:
Upgrade the motherboards latest BIOS version. Upgrade the add-on devices latest driver version.
Region: Type in your country name. E-mail: Type in your contact E-mail information. First name: Type in your first name. Last name: Type in your last name. Subject: Type in the model name and the problem of your motherboard. Example 1: AA8XE and SCSI 29160 malfunction Example 2: AA8XE boot fails, POST code AF Example 3: AA8XE (system hang when S3 resume) Motherboard: Type in the model name and revision number of your motherboard. Example: AA8XE REV: 1.00 BIOS Version: Type in the BIOS version of your motherboard. (You can find it on the screen during the POST sequence.) CPU: Type in the brand name and the speed (MHz) of your CPU. (Illustrate the over-clocking status if you had done so.) Example: Intel 650 3.4GHz (OC FSB=220MHz)
Memory brand: Type in the brand and model name of your memory module. Example: Memory brand: Kingston (KVR533D2N4/1G) Memory size: Type in the size of your memory module. Example: 512M* 4PCS Memory configuration: Type in the memory configuration in BIOS setting. Example: Memory Timing: 2.5-3-3-7 @533MHz Graphics information: Note Graphics cards brand, model and driver version Graphics card: Type in the brand and model name of your graphics card. Example: ATI RADEON X850 XT PE Graphics driver version: Type in the driver version of your graphics card Example: Catalyst 5.12V Power supply maker: Type in the brand and model name of your power supply unit. Power supply wattage: Type in the power wattage of your power supply unit. Storage devices: Type in the brand and specifications of your HDD drive and quantity. Specify if it was inserted on IDE (Master or Slave) or SATA ports, including the RAID allocation status. Example 1: WD Caviar WD600 60GB (on IDE2 master), Maxtor DiamondMax 10 SATA 300GB (on SATA 3) Example 2: Maxtor DiamondMax 10 SATA 300GB *2 (on SATA 3, SATA 4 RAID 1) Optical devices: Type in the brand and specifications of your optical drives and quantity. Specify if it was inserted on IDE (Master or Slave) or SATA ports. Other devices: Indicate which add-on cards or USB devices you are absolutely sure relate to the problem. If you cannot identify the problems origin, indicate all the add-on cards or USB devices inserted on your system. Example: AHA 29160 (on PCI 2), Sandisk Cruzer mini 256MB USB Flash-disk. Operating system: Indicate which OS and language version Example: Microsoft Windows XP SP2, English version Example: Microsoft Media Center Edition 2005, Korean version

Poland

Universal ABIT Poland (Rep. office) Strzegomska 310/2, 54-432 Wroclaw Tel: +48-71-718-12-39 Fax: +48-71-718-12-38 Contact: gmorgiel@abit.com.tw

http://www.abit.com.tw

P/N: 4310-0000-96 Rev. 1.00

STORE / LOCATION

DIRECTRON
Mail-In$10 USD Mail-In-Rebate
Universal abit I-45CV Motherboard
This offer is valid 06/01/2008 through 06/30/2008 Valid only for UPC CODE: 8433-2300-0827
INCOMPLETE FORMS MAY BE REJECTED THIS FORM ALSO CAN BE USED FOR: Axiontech.com & PC Wholesale Name (please print):_________________________________________________________________ Mailing address: _____________________________________________________________________ City:_____________________ State/Province:__________ ZIP / Postal:____________________ Daytime Phone:_____________________________ Email:___________________________________ Store Where Purchased:___________________________ Include in Mailing List? YES__ NO__ I certify by my signature that the information I have entered on this Request Form is accurate and complete, that submission of this form is in accordance with the Request Form instructions, and that I have complied with the Terms and Conditions. Signature:_______________________________________________ Date:______________________ 1. This completed form and sign (unsigned forms will be automatically denied). 2. Original sales receipt. 3. Original UPC Barcode and EAN Barcode (see example below) cut from box. Photocopies will not be accepted.

SAMPLE

890128 EAN
Mail to: Universal abit USA Rebate Center OFFER ID# 0601I-45CVDIRECTRON 3068 Laurelview Drive Fremont, CA 94538
Terms and Conditions - This offer is valid only for stand alone, retail (boxed) product printed on top of this form purchased between 06/01/200806/30/2008. - Rebate request must be postmarked by 07/21/2008 - Your receipt or bill of sale must be either typewritten or computer generated. The name appearing on this form must match the information provided on the receipt or bill of sale. - Any Request Forms lost or misdirected by the Postal Service or other delivery service are not the responsibility of Universal abit USA. - Rebate promotions should not be combined with other promotions. Combining rebates will result in processing delay or denied altogether. - Please allow 8-10 weeks for rebate checks to arrive. - Limit one rebate per name, address, household or company. - You may check your Mail In Rebate status online at the following link: http://www.abit-usa.com/rebates/tracking.php - Please make sure to have your Offer ID handy and/or a copy of this Mail In Rebate form to enter necessary information to track your rebates. - This promotion is void wherever prohibited or restricted by law. Warning: Reproduction, purchase, sale or trade of this certificate, proof-ofpurchase or cash register receipt is prohibited. Fraudulent submission could result in federal prosecution under mail fraud statutes (Title 18, United States Code, Sections 1341 and 1342). - Rebate checks are void if not cashed within 60 days of issuance and cannot be reissued. Keep a copy of your submission for future reference. Originals submitted become Universal abit USA property and will not be returned. Limit one rebate per name, address, household or company. VALID ONLY AT THE STORE PRINTED ON TOP OF THIS FORM. All other locations are disqualified.