Asus P4P8x SE
Here you can find all about Asus P4P8x SE like motherboard and other informations. For example: driver.
Asus P4P8x SE manual (user guide) is ready to download for free.
On the bottom of page users can write a review. If you own a Asus P4P8x SE please write about it to help other people. [ Report abuse or wrong photo | Share your Asus P4P8x SE photo ]
Asus P4P8x SE, size: 2.2 MB
Asus P4P8x SE
User reviews and opinions
No opinions have been provided. Be the first and add a new opinion/review.
First Edition November 2003
Copyright 2003 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (ASUS). Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners benefit, without intent to infringe.
Notices.... v Safety information... vi About this guide.... vii ASUS contact information.. viii P4P8X SE specifications summary.. ix
Chapter 1: Product introduction
1.1 1.2 1.3 1.4 1.5 1.6 1.7 Welcome!... 1-2 Package contents... 1-2 Special features... 1-3 Motherboard components.. 1-5 Motherboard layout.. 1-9 Before you proceed... 1-10 Motherboard installation..1-11 1.7.1 Placement direction...1-11 1.7.2 Screw holes...1-11 1.8 Central Processing Unit (CPU)... 1-12 1.8.1 Overview.. 1-12 1.8.2 Installing the CPU.. 1-13 1.9 System memory... 1-14 1.9.1 Memory configurations.. 1-14 1.9.2 Installing a DIMM.. 1-16 1.10 Expansion slots... 1-17 1.10.1 Standard interrupt assignments.. 1-17 1.10.2 PCI slots.. 1-18 1.10.3 AGP slot... 1-18 1.11 Jumpers... 1-19 1.12 Connectors... 1-21
Chapter 2: BIOS information
2.1 Managing and updating your BIOS. 2-2 2.1.1 Creating a bootable floppy disk.. 2-2 2.1.2 Using AFUDOS to update the BIOS.. 2-2 2.1.3 Using ASUS EZ Flash to update the BIOS. 2-4 2.1.4 Recovering the BIOS with CrashFree BIOS 2. 2-5 BIOS Setup program... 2-7 2.2.1 BIOS menu screen.. 2-8 iii
2.2.2 Menu bar... 2-8 2.2.3 Navigation keys... 2-8 2.2.4 Menu items.. 2-9 2.2.5 Sub-menu items... 2-9 2.2.6 Configuration fields.. 2-9 2.2.7 Pop-up window.. 2-9 2.2.8 Scroll bar... 2-9 2.2.9 General help... 2-9 Main menu.. 2-10 2.3.1 System Time [xx:xx:xxxx].. 2-10 2.3.2 System Date [Day xx/xx/xxxx].. 2-10 2.3.3 Legacy Diskette A [1.44M, 3.5 in.].. 2-10 2.3.4 Primary/Secondary/Third/ FourthIDE Master/Slave..2-11 2.3.5 IDE Configuration.. 2-12 2.3.6 System Information... 2-14 Advanced menu... 2-15 2.4.1 JumperFree Configuration.. 2-15 2.4.2 CPU Configuration.. 2-17 2.4.3 Chipset... 2-18 2.4.4 Onboard Devices Configuration.. 2-20 2.4.5 PCI PnP... 2-22 2.4.6 USB Configuration.. 2-23 Power menu... 2-25 2.5.1 Suspend Mode [Auto].. 2-25 2.5.2 Repost Video on S3 Resume [No].. 2-25 2.5.3 ACPI 2.0 Support [No]... 2-25 2.5.4 ACPI APIC Support [Enabled].. 2-25 2.5.5 BIOS -> AML ACPI Table [Enabled]. 2-25 2.5.6 APM Configuration.. 2-26 2.5.7 Hardware Monitor.. 2-28 Boot menu.. 2-29 2.6.1 Boot Device Priority.. 2-29 2.6.2 Boot Settings Configuration.. 2-30 2.6.3 Security... 2-31 Exit menu... 2-34
PCI slots. These five 32-bit PCI 2.2 expansion slots support bus master PCI cards like SCSI or LAN cards with 133MB/s maximum throughput. Audio CODEC. The ADI AD1888 SoundMAX is an AC97 CODEC that allows 6-channel audio playback. The audio CODEC provides six DAC channels for 5.1 surround sound, S/PDIF output, AUX and Line In stereo inputs, integrated headphone amplifier, and supports greater than 90dB dynamic range. LAN controller. This Marvell 88E8001 Gbit PCI LAN controller support 10BASE/100BASE/1000BASE-TX networking. PS/2 mouse port. This green 6-pin connector is for a PS/2 mouse. Parallel port. This 25-pin port connects a parallel printer, a scanner, or other devices. RJ-45 port. This port allows connection to a Local Area Network (LAN) through a network hub. Line In jack. This Line In (light blue) jack connects a tape player or other audio sources. In 6-channel mode, the function of this jack becomes Rear Speaker out. Line Out jack. This Line Out (lime) jack connects a headphone or a speaker. In 6-channel mode, the function of this jack becomes Front Speaker Out. Microphone jack. This Mic (pink) jack connects a microphone. In 6-channel mode, the function of this jack becomes Bass/Center Speaker Out.
The functions of the Line Out, Line In, and Microphone jacks change when you select the 6-channel audio configuration as shown in the following table:
Audio 2, 4 or 6-channel configuration
Headphone/ 2-Speaker Line In Line Out Mic In 4-Speaker Rear Speaker Out Front Speaker Out Mic In 6-Speaker Rear Speaker Out Front Speaker Out Bass/Center Speaker Out
Light Blue Lime Pink
USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. Serial port. This 9-pin COM1 port is for pointing devices or other serial devices. S/PDIF jack. This jack connects to external audio output devices. PS/2 keyboard port. This purple connector is for a PS/2 keyboard.
DDR DIMM_A1 (64 bit,184-pin module)
DDR DIMM_A2 (64 bit,184-pin module)
DDR DIMM_B1 (64 bit,184-pin module)
DDR DIMM_B2 (64 bit,184-pin module)
ATX Power Connector
PS/2KBMS KBPWR T: Mouse B: Keyboard
Top:Line In Center:Line Out Below:Mic In
Accelerated Graphics Port (AGP1)
3. Position the CPU above the socket such that its marked corner matches the base of the socket lever. 4. Carefully insert the CPU into the socket until it fits in place.
The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU!
5. When the CPU is in place, push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked. 6. Install a CPU heatsink and fan following the instructions that came with the heatsink package. 7. Connect the CPU fan cable to the CPU_FAN1 connector on the motherboard.
The motherboard comes with four Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets. These sockets support up to 4GB system memory using 184-pin unbuffered non-ECC PC3200*/2700/PC2100 DDR DIMMs. The following figure shows the location of the DDR DIMM sockets. (*Overclocking mode)
1.9.1 Memory configurations
You may install 64MB, 128MB, 256MB, 512MB, and 1GB DDR DIMMs into the DIMM sockets using the memory configurations in this section.
1. Installing DDR DIMMs other than the recommended configurations may cause memory sizing error or system boot failure. Use any of the recommended configurations in Table 1. In dual-channel configurations, install only identical (the same type and size) DDR DIMM pairs for each channel. Always install DIMMs with the same CAS latency. For optimum compatibility, it is recommended that you obtain memory modules from the same vendor. Make sure that the memory frequency matches the CPU FSB (Front Side Bus). Refer to Table 2. DIMMs installed into any three sockets will function in single-channel mode. When all four sockets are populated with 1GB DIMMs (total 4GB), the system may detect only 3+GB (a little less than 4GB) due to ICH5 resource allocation. Double-sided DDR DIMMs with x16 (databus width = 16-bit) memory chips are not supported due to chipset limitation. It is recommended to use the blue DIMM slots first.
4. 5. 6.
Recommended memory configurations
DIMM_A1 (blue) Sockets DIMM_A2 DIMM_B1 (black) (blue) DIMM_B2 (black)
(1) Populated (2) Populated (3) Populated (4) Populated Populated (1) Populated (2) Populated Populated (3)* Populated Populated Populated Populated
* For dual-channel configuration (3), you may: install identical DIMMs in all four sockets, or install identical DIMMs in DIMM_A1 and DIMM_B1 (blue sockets) and identical DIMMs in DIMM_A2 and DIMM_B2 (black sockets)
Memory frequency/CPU FSB synchronization
This motherboard supports different memory frequencies depending on the CPU FSB (Front Side Bus) and the type of DDR DIMM. CPU FSB *800 MHz 533 MHz 400 MHz * Overclocked mode
When overclocking to 800MHz CPU FSB, the system supports only DDR400 (PC3200) DIMMs due to chipset limitation. The following FSB/DDR ratios are not supported: 400/333, 400/400, 533/400.
DDR DIMM Type *PC3200 PC2700/PC2100 PC2100
Memory Frequency 400 MHz 333/266 MHz 266 MHz
Size 512MB 256MB 256MB 512MB 256MB 512MB 256MB 512MB 256MB 256MB 256MB 256MB 256MB 512MB 256MB 256MB 512MB 256MB 512MB 256MB 512MB 512MB 256MB
DDR400 Qualified Vendor List (QVL) (Overclocked Mode)
Vendor P/N Number M2G9J16AGATT9F081AA4T M2S9I08AFAPS9F0811A-T 77.10636.465 77.10736.464 TS32MLD64V4F3 TS64MLD64V4F3 TS32MLD64V4F3 TS64MLD64V4F3 MDOAD5F3G315B1ECZ MDOSS6F3G31JB1EAE MDOWB5F3G316B1EAE W9425GCDB-5 W9451GCDB-5 HYS64D16301GU-5-B HYS64D32300GU-5-B HYS64D64320GU-5-B M368L3223ETM-CCC M368L6432ETM-CCC HYMD232646B8J-D43 AA HYMD264646B8J-D43 AA MT16VDDT6464AG-40BC4 MT8VDDT3264AG-40BC4 DS/SS DS SS SS DS SS DS SS DS SS SS SS SS SS DS SS SS DS SS DS SS DS DS SS Component TMD7608F8E50D A2S56D30ATP K4H560838D-TCC4 K4H560838D-TCC4 K4H560838D-TCC4 K4H560838D-TCC4 V58C2256804SAT5 V58C2256804SAT5 ADD8608A8A-5B K4H560838D-TCC4 W942508BH-5 W942508BH-5 W942508BH-5 W942508BH-5 HYB25D256160BT-5B HYB25D256800BT-5B HYB25D256800BT-5B K4H560838E-TCCC K4H560838E-TCCC HY5DU56822BT-D43 HY5DU56822BT-D43 MT46V32M8TG-5BC MT46V32M8TG-5BC Max. DIMMs 2
TwinMOS TwinMOS Apacer Apacer Transcend Transcend Transcend Transcend A DATA A DATA A DATA Winbond Winbond Infineon Infineon Infineon SAMSUNG SAMSUNG Hynix Hynix MICRON MICRON
Obtain DDR DIMMs only from ASUS qualified vendors for better system performance. Visit the ASUS website (www.asus.com) for the latest QVL. FSB800 and DDR400 is not a default specification, take caution when overclocking your system.
1.9.2 Installing a DIMM
Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components.
Follow these steps to install a DIMM. 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. 3. Firmly insert the DIMM into the socket until the retaining clips snap back in Unlocked Retaining Clip place and the DIMM is properly seated.
Managing and updating your BIOS
The original BIOS file for this motherboard is in the support CD. Copy the original BIOS to a bootable floppy disk in case you need to restore the BIOS in the future.
2.1.1 Creating a bootable floppy disk
1. Do either one of the following to create a bootable floppy disk. DOS environment Insert a 1.44 MB floppy disk into the drive. At the DOS prompt, type: format A:/S <Enter> Windows environment a. From your Windows desktop, click on Start, point to Settings, then click on Control Panel. b. Double-click on Add/Remove Programs icon from the Control Panel window. c. Click on the Startup Disk tab, then on Create Disk. button. d. Insert a 1.44 MB floppy disk when prompted. Follow the succeeding screen instructions to complete the process. 2. Copy the original (or the latest) motherboard BIOS to the bootable floppy disk.
2.1.2 Using AFUDOS to update the BIOS
Update the BIOS using the AFUDOS.EXE utility in DOS environment. 1. Visit the ASUS website (www.asus.com) to download the latest BIOS file for your motherboard. Save the BIOS file to a bootable floppy disk.
Write down the BIOS file name to a piece of paper. You need to type the exact BIOS file name at the prompt.
2. Copy the AFUDOS.EXE utility from the support CD to the bootable floppy disk that contains the BIOS file. 3. Boot the system from the floppy disk.
DO NOT use the P4P8X BIOS file for this motherboard.
4. At the DOS prompt, type the command line: afudos /i<filename> where filename means the latest (or original) BIOS file that you copied to the bootable floppy disk. The screen displays the status of the update process.
The BIOS information on the screen is for reference only. What you see on your screen may not be exactly the same as shown.
A:\>afudos /ip4p8xse.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading file.. done Erasing flash. done Writing flash. 0x0008CC00 (9%)
DO NOT shutdown or reset the system while updating the BIOS! Doing so may cause system boot failure!
When the BIOS update process is complete, the utility returns to the DOS prompt.
A:\>afudos /ip4p8xse.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading file.. done Erasing flash. done Writing flash. 0x0008CC00 (9%) Verifying flash. done A:\>
5. Reboot the system from the hard disk.
2.1.3 Using ASUS EZ Flash to update the BIOS
The ASUS EZ Flash feature allows you to easily update the BIOS without having to go through the long process of booting from a diskette and using a DOS-based utility. The EZ Flash is built-in the BIOS firmware so it is accessible by simply pressing <Alt+F2> during the Power-On Self Tests (POST).
Because the BIOS software is constantly being updated, the following BIOS setup screens and descriptions are for reference purposes only, and may not exactly match what you see on your screen.
2.2.1 BIOS menu screen
Menu items Menu bar Configuration fields General help
System Time System Date Legacy Diskette A Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration System Information
[11:10:19] [Thu 03/27/2003] [1.44M, 3.5 in] :[ST320413A] :[ASUS CD-S340] :[Not Detected] :[Not Detected] :[Not Detected] :[Not Detected]
Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time.
+Tab F1 F10 ESC
Select Screen Select Item Change Field Select Field General Help Save and Exit Exit
2.2.2 Menu bar
The menu bar on top of the screen has the following main items:
Main Advanced Power Boot Exit For changing the basic system configuration For changing the advanced system settings For changing the advanced power management (APM) configuration For changing the system boot configuration For selecting the exit options and loading default settings
To select an item on the menu bar, press the right or left arrow key on the keyboard until the desired item is highlighted.
2.2.3 Navigation keys
At the bottom right corner of a menu screen are the navigation keys for that particular menu. Use the navigation keys to select items in the menu and change the settings.
Some of the navigation keys differ from one screen to another.
2.2.4 Menu items
The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items. The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items.
System Time System Date Legacy Diskette A Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration System Information [11:10:19] [Thu 03/27/2003] [1.44M, 3.5 in] :[ST320413A] :[ASUS CD-S340] :[Not Detected] :[Not Detected] :[Not Detected] :[Not Detected] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time.
Main menu items
2.2.5 Sub-menu items
An item with a sub-menu on any menu screen is distinguished by a solid triangle before the item. To display the sub-menu, select the item and press Enter.
2.2.6 Configuration fields
These fields show the values for the menu items. If an item is user- configurable, you may change the value of the field opposite the item. You can not select an item that is not user-configurable. A configurable field is enclosed in brackets, and is highlighted when selected. To change the value of a field, select it then press Enter to display a list of options. Refer to 2.2.7 Pop-up window.
2.2.7 Pop-up window
Select a menu item then press Enter to display a pop-up window with the configuration options for that item.
Configure System Frequency/Voltage AI Overclock Tuner CPU External Frequency (MHz) DRAM Frequency AGP/PCI Frequency (MHz) CPU VCore Voltage DDR Reference Voltage AGP VDDQ Voltage [Manual]  [333 Mhz] [Auto] [Auto] [Auto] [1.50V] [Auto] +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit
2.2.8 Scroll bar
A scroll bar appears on the right side of a menu screen when there are items that do not fit on the screen. Press Up/Down arrow keys or PageUp/PageDown keys to display the other items on the screen.
Pop-up window Scroll bar
2.2.9 General help
At the top right corner of the menu screen is a brief description of the selected item.
When you enter the BIOS Setup program, the Main menu screen appears giving you an overview of the basic system information.
Refer to section 2.2.1 BIOS menu screen for information on the menu screen items and how to navigate through them.
2.3.1 System Time [xx:xx:xxxx]
This item allows you to set the system time.
2.3.2 System Date [Day xx/xx/xxxx]
This item allows you to set the system date.
2.3.3 Legacy Diskette A [1.44M, 3.5 in.]
Sets the type of floppy drive installed. Configuration options: [Disabled] [360K, 5.25 in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.] [2.88M, 3.5 in.]
2.3.4 Primary/Secondary/Third/Fourth IDE Master/Slave
While entering Setup, BIOS auto-detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press Enter to display the IDE device information.
Primary IDE Master Device : Hard Disk Vendor : ST320413A Size : 20.0GB LBA Mode : Supported Block Mode : 16 Sectors PIO Mode : 4 Async DMA : MultiWord DMA-2 Ultra DMA : Ultra DMA-5 SMART Monitoring: Supported Type LBA/Large Mode Block (Multi-sector Transfer) PIO Mode DMA Mode Smart Monitoring 32Bit Data Transfer [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Disabled]
Select the type of device connected to the system.
+F1 F10 ESC
Select Screen Select Item Change Option General Help Save and Exit Exit
The values opposite the dimmed items (Device, Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra DMA, and SMART monitoring) are autodetected by BIOS and are not user-configurable. These items show N/A if no IDE device is installed in the system.
Selects the type of IDE drive. Configuration options: [Not Installed] [Auto] [CDROM] [ARMD]
LBA/Large Mode [Auto]
Enables or disables the LBA mode. Setting to Auto enables the LBA mode if the device supports this mode, and if the device was not previously formatted with LBA mode disabled. Configuration options: [Disabled] [Auto]
Block (Multi-sector Transfer) [Auto]
Enables or disables data multi-sectors transfers. When set to Auto, the data transfer from and to the device occurs multiple sectors at a time if the device supports multi-sector transfer feature. When set to Disabled, the data transfer from and to the device occurs one sector at a time. Configuration options: [Disabled] [Auto]
PIO Mode [Auto]
Selects the PIO mode. Configuration options: [Auto]     
DMA Mode [Auto]
Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5]
SMART Monitoring [Auto]
Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled]
32Bit Data Transfer [Disabled]
Enables or disables 32-bit data transfer. Configuration options: [Disabled] [Enabled]
2.3.5 IDE Configuration
The items in this menu allows you to change the settings for the IDE devices installed in the system. Select an item then press Enter if you wish to configure the item.
IDE Configuration Onboard IDE Operate Mode Enhanced Mode Support On IDE Detect Time Out (Sec) [Enhanced Mode] [S-ATA] 
Onboard IDE Operate Mode [Enhanced Mode]
Allows selection of the IDE operation mode depending on the operating system (OS) that you installed. Set to Enhanced Mode if you are using native OS, such as Windows 2000/XP. Set to Compatible Mode if you are using legacy OS including MS-DOS, Windows ME/98/NT4.0. Configuration options: [Compatible Mode] [Enhanced Mode]
The items in this menu show the CPU-related information auto-detected by BIOS.
Configure advanced CPU settings Manufacturer Brand String Frequency : Intel(R) : Intel(R) Pentium(R) 4 CPU 1.73GHz : 1733 MHz
Ratio Status : Locked Ratio Actual Value : 13 CPUID Maximum Value Limit
CPUID Maximum Value Limit [Enabled]
Configuration options: [Disabled] [Enabled]
The Chipset menu items allow you to change the advanced chipset settings. Select an item then press Enter to display the sub-menu.
Advanced Chipset settings WARNING: Setting wrong values in the sections below may cause system to malfunction. Configure DRAM Timing by SPD Memory Acceleration Mode DRAM Idle Timer DRAm Refresh Rate Graphic Adapter Priority Graphics Aperture Size Spread Spectrum ICH Delayed Transaction MPS Revision [Enabled] [Auto] [Auto] [Auto] [AGP/PCI] [ 64 MB] [Enabled] [Enabled] [1.4] +F1 F10 ESC
Configure DRAM Timing by SPD [Enabled]
When this item is enabled, the DRAM timing parameters are set according to the DRAM SPD (Serial Presence Detect). When disabled, you can manually set the DRAM timing parameters through the DRAM sub-items. Configuration options: [Disabled] [Enabled]
Memory Acceleration Mode [Auto]
This field when [Enabled] minimize latencies from CPU to memory to boost system performance. Configuration options: [Auto] [Enabled]
Setting to [Enabled] may cause the system to become unstable! If this happens, revert to the default setting [Auto].
DRAM Idle Timer [Auto]
Configuration options: [Infinite] [0T] [8T] [16T] [64T] [Auto]
DRAM Refresh Mode [Auto]
Configuration options: [Auto] [15.6 uSec] [7.8 uSec] [64 uSec] [64T]
If the system becomes unstable after changing the settings of any of the above items, revert to the default settings. The following sub-items appear only when the item Configure DRAM Timing by SPD is set to Disabled.
DRAM CAS# Latency [2.5 Clocks]
This item controls the latency between the SDRAM read command and the time the data actually becomes available. Configuration options: [2.0 Clocks] [2.5 Clocks] [3.0 Clocks]
DRAM RAS# Precharge [4 Clocks]
This item controls the idle clocks after issuing a precharge command to the DDR SDRAM. Configuration options: [4 Clocks] [3 Clocks] [2 Clocks]
The Device items appear only when there are installed USB devices.
The Power menu items allow you to change the settings for the Advanced Power Management (APM). Select an item then press Enter to display the configuration options.
Suspend Mode Repost Video on S3 Resume ACPI 2.0 Support ACPI APIC Support BIOS -> AML ACPI table APM Configuration Hardware Monitor
[Auto] [No] [No] [Enabled] [Enabled]
2.5.1 Suspend Mode [Auto]
Allows you to select the ACPI state to be used for system suspend. Configuration options: [S1 (POS) Only] [S3 Only] [Auto]
2.5.2 Repost Video on S3 Resume [No]
Determines whether to invoke VGA BIOS POST on S3/STR resume. Configuration options: [No] [Yes]
2.5.3 ACPI 2.0 Support [No]
Allows you to add more tables for ACPI 2.0 specifications. Configuration options: [No] [Yes]
2.5.4 ACPI APIC Support [Enabled]
Allows you to enable or disable the ACPI support in the ASIC. When set to Enabled, the ACPI APIC table pointer is included in the RSDT pointer list. Configuration options: [Disabled] [Enabled]
2.5.5 BIOS -> AML ACPI Table [Enabled]
Allows you to enable or disable the inclusion of the BIOS ->AML exchange pointer to (X)RSDT pointer list. Configuration options: [Disabled] [Enabled]
2.5.6 APM Configuration
APM Configuration Power Management/APM Video Power Down Mode Hard Disk Power Down Mode Suspend Time Out Throttle Slow Clock Ratio System Thermal Power Button Mode Restore on AC Power Loss Power Power Power Power Power On On On On On By By By By By RTC Alarm External Modem PCI Devices PS/2 Keyboard PS/2 Mouse [Enabled] [Suspend] [Suspend] [Disabled] [50%] [Disabled] [On/Off] [Power Off] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit Enabled or disable APM.
Power Management/APM [Enabled]
Allows you to enable or disable the Advanced Power Management (APM) feature. Configuration options: [Disbaled] [Enabled]
Video Power Down Mode [Suspend]
Allows you to select the video power down mode. Configuration options: [Disabled] [Standby] [Suspend]
Hard Disk Power Down Mode [Suspend]
Allows you to select the hard disk power down mode. Configuration options: [Disabled] [Standby] [Suspend]
Standby Time Out [Disabled]
Allows you to select the specified time at which the system goes on standby. Configuration options: [Disabled] [1 Min] [2 Min] [4 Min] [8 Min] [10 Min] [20 Min] [30 Min] [40 Min] [50 Min] [60 Min]
Suspend Time Out [Disabled]
Allows you to select the specified time at which the system goes on suspend. Configuration options: [Disabled] [1 Min] [2 Min] [4 Min] [8 Min] [10 Min] [20 Min] [30 Min] [40 Min] [50 Min] [60 Min]
2.5.7 Hardware Monitor
Hardware Monitor CPU Temperature MB Temperature Power Temperature CPU Fan Speed Chassis Fan Speed Power Fan Speed VCORE Voltage 3.3V Voltage 5V Voltage 12V Voltage [44C/111F] [36C/96.5F] [N/A] [2250RPM] [N/A] [N/A] [1.550V] [3.386V] [4.890V] [11.900V] CPU temperature
CPU Temperature [xxxC/xxxF] or [N/A] MB Temperature [xxxC/xxxF] or [N/A] Power Temperature [xxxC/xxxF] or [N/A]
The onboard hardware monitor automatically detects and displays the motherboard, CPU, and power supply temperatures. If any of the features is not available to the motherboard, the specific field shows N/A.
CPU Fan Speed [xxxxRPM] or [N/A] Chassis Fan Speed [xxxxRPM] or [N/A] Power Fan Speed [xxxxRPM] or [N/A]
The onboard hardware monitor automatically detects and displays the CPU and chassis fan speeds in rotations per minute (RPM). If any of the fans is not connected to the motherboard, the specific field shows N/A.
VCORE Voltage, +3.3V Voltage, +5V Voltage, +12V Voltage
The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators.
If any of the monitored items is out of range, the following error message appears: Hardware Monitor found an error. Enter Power setup menu for details. You will then be prompted to Press F1 to continue or DEL to enter SETUP.
The Boot menu items allow you to change the system boot options. Select an item then press Enter to display the sub-menu.
Boot Settings Boot Device Priority Boot Settings Configuration Security
Specifies the Boot Device Priority sequence.
2.6.1 Boot Device Priority
Boot Device Priority 1st Boot Device 2nd Boot Device 3rd Boot Device [First Floppy Drive] [PM-ST320413A] [PS-ASUS CD-S340] Specifies the boot sequence from the available devices. A device enclosed in parenthesis has been disabled in the corresponding type menu. Select Screen Select Item Change Option General Help Save and Exit Exit
1st ~ xxth Boot Device [1st Floppy Drive]
These items specify the boot device priority sequence from the available devices. The number of device items that appear on the screen depends on the the number of devices installed in the system. Configuration options: [xxxxx Drive] [Disabled]
2.6.2 Boot Settings Configuration
Boot Settings Configuration Quick Boot Full Screen Logo Add On ROM Display Mode Bootup Num-Lock PS/2 Mouse Support Typematic Rate Boot to OS/2 Wait for F1 If Error Hit DEL Message Display Interrupt 19 Capture [Enabled] [Disabled] [Force BIOS] [On] [Auto] [Fast] [No] [Enabled] [Enabled] [Disabled]
Select this item to set or change the supervisor password. The Supervisor Password item on top of the screen shows the default Not Installed. After you have set a password, this item shows Installed. To set a Supervisor Password: 1. Select the Change Supervisor Password item and press Enter. 2. On the password box that appears, type a password composed of letters and/ or numbers, then press Enter. Your password should have at least six characters. 3. Confirm the password when prompted. The message Password Installed appears after you have successfully set your password. The Supervisor Password item now shows Installed. To change the supervisor password, follow the same steps as in setting a user password. To clear the supervisor password, select the Change Supervisor Password then press Enter. The message Password Uninstalled appears. After you have set a supervisor password, the other items appear to allow you to change other security settings.
Security Settings Supervisor Password User Password Change Supervisor Password User Access Level Change User Password Clear User Password Password Check Boot Sector Virus Protection Installed Not Installed [Full Access] [Setup] [Disabled]
User Access Level (Full Access]
This item allows you to select the access restriction to the Setup items. Configuration options: [No Access] [View Only] [Limited] [Full Access] No Access prevents user access to the Setup utility. View Only allows access but does not allow change to any field. Limited allows change to only selected fields, such as Date and Time. Full Access allows viewing and changing all the fields in the Setup utility.
Change User Password
Select this item to set or change the user password. The User Password item on top of the screen shows the default Not Installed. After you have set a password, this item shows Installed. To set a User Password: 1. Select the Change User Password item and press Enter. 2. On the password box that appears, type a password composed of letters and/ or numbers, then press Enter. Your password should have at least six characters. 3. Confirm the password when prompted. The message Password Installed appears after you have successfully set your password. The User Password item now shows Installed. To change the user password, follow the same steps as in setting a user password.
Clear User Password
Select this item if you wish to clear the user password.
Password Check [Setup]
When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system. Configuration options: [Setup] [Always]
Boot Sector Virus Protection [Disabled]
Allows you to enable or disable the boot sector virus protection. Configuration options: [Disabledc] [Enabled]
The contents of the support CD are subject to change at any time without notice. Visit the ASUS website for updates.
3.2.1 Running the support CD
To begin using the support CD, simply insert the CD into your CD-ROM drive. The CD automatically displays the Drivers menu if Autorun is enabled in your computer.
Click an item to install
Click an icon to display more information
If Autorun is NOT enabled in your computer, browse the contents of the support CD to locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run the CD.
3.2.2 Drivers menu
The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices.
Intel Chipset Inf Update program
This item installs the Intel Chipset INF Update Program that enables Plug-n-Play INF support for Intel chipset components. This utility installs to the target system the Windows INF files that outline to the operating system how the chipset components will be configured. Refer to the online help or readme file that came with the utility.
SoundMAX Audio Driver and Application
This item installs the AC97 audio driver and applications to activate the 6-channel audio feature. After installing the driver and SoundMAX Integrated Audio icon applications, the SoundMAX Integrated Audio icon appears on the taskbar. Double-click the icon to display the SoundMAX Control Panel from which you can adjust to 6-channel audio settings.
USB 2.0 Driver
This item installs the USB 2.0 driver.
Marvell Gigabit LOM Driver
This item installs the Marvell Gigabit LAN On Motherboard (LOM) Ethernet driver to support 10/100/1000 Mbps networking.
3.2.3 Utilities menu
The Utilities menu shows the applications and other software that the motherboard supports.
ASUS PC Probe
This smart utility monitors the fan speed, CPU temperature, and system voltages, and alerts you on any detected problems. This utility helps you keep your computer at a healthy operating condition.
Install ASUS Update
This program allows you to download the latest version of the BIOS from the ASUS website. Before using the ASUS Update, make sure that you have an Internet connection so you can connect to the ASUS website. Installing ASUS Update also installs ASUS Mylogo.
This item installs the PC-cillin 2002 anti-virus program. View the PC-cillin online help for detailed information.
Adobe Acrobat Reader
This item installs the Adobe Acrobat Reader V5.0. The Acrobat Reader software is for viewing files saved in Portable Document Format (PDF).
ASUS Screen Saver
This item installs the ASUS screen saver.
3.2.4 ASUS Contact Information
TX-P42s20E Schtb10EG Estate 85394 Nikkor EF4116 NV-XYZ777 FAX-JX201 SGH-E300 VP-D307I PL200 DVD-P185 W1206 Speaker Avsf 109 Smart 20U63 TH-50PX8EA N6000 PVM266AM-P Polar F4 Flipper Xdpu50D WAG102 SR-50 3 ME Kaiser NV-U92T Aspire-T160 GA610 RT-7000 CD6401B 53 KDL-40W5710 DI2510F CDR765-00 1800-750 50 R CW-25M064N Nawigatorem SH-S223F Uk Driver LAC4810 Server FS-1118 Mitsubishi P93 Escort 5580 F1446 TTR50-2008 RAR381 Vigor 2820 MDD262 AN-M2 Ultimate 30BF CT-W504R RMX 2000 PSR-1500 AX3000B 67-320 Hdmi Alcatel-lucent 4068 PC 5010 GM-X334 TH-50PH9 R-1610 TX-26LXD80F KDC-MP2028 RX200 S5 5001 ECO Samsung 94V ICF-M60srds 4300BV A-223 82028 LE37A626 6600T 300-08 DX-B350P SL-PG540A Prophesy KX-T7540CEB HT-TX715 100-R STB-1001S GT-C6112 Ducati 749 Phone-MD7261 CD3000XL Powershot A310 The Dead TCC-2510 HT762TZR IC-R20 C3212 MJ-D707 PRO K550 DV-HRD3 Theme Park Chipset Izek 1500 RDZ-D5 Coupe
manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101