Ensure that the unit is securely installed. Otherwise it may fly out of place during collisions and other jolts. When extending the ignition, battery or ground wires, make sure to use automotive-grade wires or other wires with an area of 0.75mm2 (AWG18) or more to prevent cable deterioration and damage to the cable coating. To prevent short circuits, never put or leave any metallic objects (e.g., coins or metal tools) inside the unit. If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer. Do not touch the liquid crystal fluid if the LCD is damaged or broken due to shock. The liquid crystal fluid may be dangerous to your health or even fatal. If the liquid crystal fluid from the LCD contacts your body or clothing, wash it off with soap immediately.

2CAUTION

Audio units you can control from the DDX7015/7045 Receiver (in November of 2003):
KDC-CX89, KDC-CX87, KDC-CX85, KDC-C719, KDC-C717, KDC-C715, KDC-C669, KDC-C667, KDC-C665, KDC-C469, KDC-C467, KDC-C465, KDC-D301, KTC-9090DAB, KDV-C830, KDV-C840, KDV-C860, KDC-CX89, KTC-SR901, KTC-SR902, KPA-CP100, KTC-WB100, KTC-V500N/P/E (Set the "O-N" switch to "N" position if provided.)
Region codes in the world
The DVD players are given a region code according to the country or area it is marketed, as shown in the following map.
Navigation units you can control from the DDX7015/7045 Receiver (in November of 2003):

KNA-DV2100, KNA-DV3100

Loading and Replacing the battery
Use one lithium battery (CR2025). Insert the batteries with the + and - poles aligned properly, following the illustration inside the case.
To prevent damage to the machine, take the following precautions:
Make sure to ground the unit to a negative 12V DC power supply. Do not open the top or bottom covers of the unit. Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Do not subject the faceplate to excessive shock, as it is a piece of precision equipment. When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction. To prevent short circuits when replacing a fuse, first disconnect the wiring harness. Do not use any screws except for the ones provided. The use of improper screws might result in damage to the main unit. You cannot view video pictures whilst the vehicle is moving. To enjoy TV/video pictures, find a safe place to park and engage the parking brake.

NOTE 2WARNING

Icons on the DVD discs
Icon Description Indicates the region code where the disc can be played.
Store unused batteries out of the reach of children. Contact a doctor immediately if the battery is accidentally swallowed.
Do not set the remote on hot places such as above the dashboard. The provided batteries are intended for use in operation checking, and their service life may be short. When the remote controllable distance becomes short, replace both of the batteries with new ones.
Number of voice languages recorded with the audio function. The number in the icon indicates the number of voice languages. (Max. 8 languages) Number of subtitle languages recorded with the subtitle function. The number in the icon indicates the number of subtitle languages. (Max. 32 languages) Number of angles provided by the angle function. The number in the icon indicates the number of angles. (Max. 9 angles) Aspect ratios that can be selected. "LB" stands for Letter Box and PS for Pan/Scan. In the example on the left, the 16:9 video can be converted into letter box video.

16:9 LB

Cleaning the panel and monitor
When the operator panel and monitor panels are dirty, wipe and clean them using a soft cloth (such as a commercially available silicon coated cloth). When contaminated excessively, clean them using a cloth dipped in a neutral detergent first, then remove the detergent using a dry cloth. Do not use a hard cloth and a volatile chemical (such as an alcohol). If used, the panel surface may be scratched or printed letters may be erased.

Unplayable discs

This player cannot play back any of the following discs. DVD-ROM/DVD-RAM discs HQ-VCD discs CDV discs (Only the audio part can be reproduced) CD-G/CD-EG/CD-EXTRA discs (Only the audio can be reproduced) Photo CD discs DVD-Audio Also, you cannot play back the DVD-R/RW and DVD+R/RW discs if not recorded in the DVD-Video format.
If you experience problems during installation, consult your Kenwood dealer. If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer.

Cleaning the disc slot

As dust can accumulate in the disc slot, clean it occasionally. Your discs can get scratched if you put them in a dusty disc slot.

Lens Fogging

Loading such a medium may produce loud noise to damage the speakers. Do no attempt to play a medium containing a nonMP3/WMA file with the MP3/WMA extension. The unit mistakes non-MP3/WMA files for MP3/WMA data as long as they have the MP3/WMA extension. Do not attempt to play a medium containing non MP3/WMA.

When using a new disc

If the disc center hole or outside rim has burrs, use it after removing them with a ball pen etc.

Burrs Burrs

Disc storage
Dont place them in direct sunlight (On the seat or dashboard etc.) and where the temperature is high. Store discs in their cases.

MP3/WMA playing order

When selected for play, Folder Search, File Search, or for Folder Select, files and folders are accessed in the order in which they were written by the CD writer. Because of this, the order in which they are expected to be played may not match the order in which they are actually played. You may be able to set the order in which MP3/WMA are to be played by writing them onto a medium such as a CD-R with their file names beginning with play sequence numbers such as "01" to "99", depending on your CD writer.
Settings for your MP3/WMA encoder and CD writer Disc accessories
Dont use disc type accessories. Do the following setting when compressing audio data in MP3/WMA data with the MP3/WMA encoder. Transfer bit rate: MP3: kbps WMA: kbps Sampling frequency: MP3: 32, 44.1, 48 kHz WMA: 32, 44.1, 48 kHz When you use your CD writer to record MP3/WMA up to the maximum disc capacity, disable additional writing. For recording on an empty disc up to the maximum capacity at once, check Disc at Once.
Play mode may not be possible when portions of the functions of Windows Media Player 9 or higher are used.

Disc cleaning

Clean from the center of the disc and move outward.

Entering ID3 tag

The Displayable ID3 tag is ID3 version 1.x. For the character code, refer to the List of Codes.

6 English

English 7
DDX7015/7045 Basic operation
1 Play Disc [Disc insertion slot] 7 Track/Station Selectors [SEEK] key Selects a music or chapter, track, or frequency. 8 Attenuator/Loudness [ATT]/[LOUD] key Attenuates the volume. Press it again to cancel muting. Press it for more than one second to turn the Loudness function on or off. If turned on, high and low tones are enhanced during low volume. 9 Select Seek Mode [AUTO] key Selects the Seek mode. (see pages 22/36 for the <Seek Mode>) p Screen Setup [SCRN] key

English 8 English

A disc is played when you insert it. 2 Play/Pause [38] key Pauses and replays a disc. 3 Eject Disc [EJECT] key The disc is ejected. 4 Switch Video Sources [V.SEL] key The video sources are switched each time you press the key.

Displays the Screen Setup or Angle Setup screen. (see page 58)

* Optional accessory

Clears the video image when pressed more than one second. When pressed again, the original image is redisplayed. 5 Switch Audio Source/Power Supply [SRC] key The audio sources are switched each time you press the key.
q Function [FNC] key The video sources are switched each time you press the key.
Switches the source that is output at the AV OUTPUT terminal when it is pressed more than 1 second. w Switch Screen Mode [MODE] key The screen mode is switched. (see page 12)
Hold down more than 1 second to turn the power supply Off. Push it again to turn power supply On. 6 Volume Controls [VOL] key
The display turns on when you put the parking brake, except for the navigation system.

English 9

Basic Operations of Remote Controller
6 Joystick [DVD] [VCD] t [DISC] Select a folder or a disc. [TV] FM: Switches to TV1, TV2, or VIDEO. [TUNER] FM: Switches to the FM1, FM2, or FM3 band. AM: Switches to the AM band. y [DISC] 4 or : Selects a chapter, a track or a song. [TV] 4 or : Select a channel. [TUNER] 4 or : Selects a station. u [DVD] 1: Fast Backward (Rewind). The speed changes each time it is pressed. : Fast Forward. The speed changes each time it is pressed. i [TV] [TUNER] Call the stations from memory. o [DISC] Plays or pauses. [TUNER] Selects the Seek mode. (see page 22/44 for the <Seek Mode>) ; [DVD] : Slow Backward. : Slow Forward. a Attenuator [ATT] key Attenuates the volume. Press it again to cancel muting.
1 Remote Control Mode selector Selects one of the following remote control modes. TV: TV source DVD: Built-in DVD/VCD/CD/MP3/WMA/WMA player source AUD: Tuner source or attached disc changer/disc player source 2 Volume Control Adjusts the volume. 3 [DISC] Stops to play the built-in disc player. 4 Switches over the sound source each time it is pressed. 5 Selects the Direct Search mode. (see pages 19/24/33/37 for <Direct Search>)
Enters your selection from the DVD/VCD Disc Menu. 7 [DVD] [VCD] Returns to the previous screen when the DVD/VCD Disc Menu is used. 8 [DVD] Calls the Top menu of DVD Disc Menu. 9 Switch Video Sources [V.SEL] key The video sources are switched each time you press the key.
Clears the video image when pressed more than one second. When pressed again, the original image is redisplayed. p [DVD] Calls the DVD Disc Menu. q [DVD] [VCD] Each time you press the button, the angle switch. w [DVD] [VCD] Each time you press the button, the zoom raito switch. e [DVD] Switches a subtitle language.(See <Language Setup>, page 68) r [DVD] Switches an audio language.(See <Language Setup>, page 68)

5 Exit the Set Name mode

You can store up to 30 stations in memory. You can set a station name only after you have applied the parking brake.
2 Select the Auto Memory mode
If AME is not shown, touch

3 Start Auto Memory

Auto Memory terminates when 6 stations are stored or when all stations are tuned in.

22 English

English 23
Tunes in a station when its frequency is entered. 1 Select a band

Traffic Information

When a traffic bulletin starts, any source is switched to the traffic information and it is displayed automatically. When the traffic bulletin starts.
The Traffic Information screen appears automatically. Traffic Information screen

Search for Program Type

A program is tuned when you set its program type.

1 Call the Tuner Menu

Radio Text
You can display the radio text.

Menu Menu

Display the Radio Text
2 Selects the Direct Search mode

Direct SRC

IN TI ATT NEWS AF

Call the PTY Search Menu

Rad i o -T e x t PTY Sea r c h

3 Enter a frequency

Tr a f f i c I n f o m a t i o n

All Speech All Music

Rad i o
1 Calls the Sound Effects Menu. (see page 84) 2 Switches the source. 3 Calls the Setup Menu. (see page 57) 4 Turns the Traffic Information function on or off.
During reception of traffic information the adjusted volume is automatically remembered, and the next time it switches to traffic information it's automatically the remembered volume.
News Current Affairs Information Not Found Re t u r n
When you enter them, signal reception starts. Example: When you receive FM 92.1 MHz Example: When you receive AM 810 kHz

SRCH 3 FM 98.1

1 Selects a program type. 2 Scrolls the program type list. 3 Searches for the program type. It is displayed when the Program Type is selected. 4 Returns to the Tuner Menu.
1 Displays the Radio Text. 2 Scrolls the Radio Text. It is displayed when information cannot be displayed on a single screen page. 3 Returns to the Tuner Menu.

Select a program type

Search for the program type

24 English

English 25
CD/MP3/WMA/WMA/Disc Changer Play Control
You can call various control screens during CD/MP3/WMA/WMA/Disc Changer playback.
The CD/MP3/WMA/Disc Changer Play Control Panel is displayed in a floating position of the selected picture. 1 Switches the source. 2 Stops to play the built-in disc player. 3 When a CD is played back on the built-in disc player: Rewinds or fast forwards. 4 Selects a song. When a disc is played back on an external disc player, a disc changer or the MP3/WMA/WMA, continue to touch this key to start rewinding or fast forwarding.

Displaying the CD/MP3/WMA/ Disc Changer Control screen
You can play the CD/MP3/WMA/disc changer using various functions.
During CD playback 8 Calls the CD Menu. 9 Calls the Sound Effects Menu. (see page 84) p Displays the Source Select screen. (see page 55) q Calls the Setup Menu. (see page 57)
Display of Easy Control Panel During CD playback

DVD CD MODE: F U L L

CD Control screen

DVD CD

w Ejects the disc from the built-in disc player. e Fast Forwards or Rewinds.
5 Plays or pauses. 6 When an MP3/WMA/WMA is played back on the built-in disc player: Selects a folder.

13:50 25

r Selects a track.
t Plays or pauses. y Starts or stops Scan Play (that plays the beginning of each song one after the other). u Repeats to play (the present track). i Starts or stops Random Play (to play songs in random order). o Selects the Disc Name (see <Set Disc Name>, page 30), Disc Text, or Track Text mode for text display. ; Scrolls the display text. a Switches the play time display between Track, Disc, and Disc Remaining Time. s Track Number Display d Play Time Display

1 SRC DVD CD

7 When a disc is played back on the disc changer: Selects a disc.
For CD/MP3/WMA/WMA/Disc Changer playback and receiver key operations, see <DDX7015/7045 Basic Operations> (see page 8). The Easy Control Panel display is cleared when you touch the center of image display area.
17 SCN REP RDM 22 T r a c k 4 26

P 2 : 23

Track 3

During MP3/WMA playback

SRC DVD MP3/WMA

P 0:05:32

During playback on disc changer

SRC CD CH

f Appears when a disc is inserted.

3 D + T3

P 5:32
g Stops to play the built-in disc player. When pressed twice, the disc is played from its beginning when you play it in the next time. h Function Indicator
During playback on CD player

1 Scrolls the list.

1 Plays the displayed disc. 2 Selects the Disc Name or Disc Text mode for text display. 3 Scrolls the list. (It is not displayed when a disc changer having 6 or less discs is used.)
During play on an external in disc player or disc changer 1 Enter a disc or track number
The system restarts to play while the phone call is continued.
3 Select the desired disc

1. D i s c N a me

When the call ends.
Hang up the phone. The system restarts to play.

2 Search

Touch the desired disc display. When searching for a song:
When searching for a disc:

32 English

English 33

TV Control

TV Control (with the optional accessory TV Tuner connected only)
Various control screens appear in the TV Source mode.
Displaying the TV Picture screen

Selects the TV Pictures.

Displaying the TV Control screen
1 TV Band Number Display 2 Memory Number Display 3 Channel Number Display 4 Channel Up Area Increase the channel. You can tune in a TV station using various functions. e Calls the TV Menu. r Calls the Sound Effects Menu. (see page 84) t Displays the Source Select screen. (see page 55) y Calls the Setup Menu. (see page 57) TV Control screen

TV Picture screen

u Switches to VIDEO. i Switches to TV1 or TV2.
Preset 3 2ch MODE: F U L L AV-OUT: AV - I N 4 6
5 Channel Down Area Decrease the channel. 6 Band/Video Switch Area Switches to TV1, TV2, or VIDEO. 7 Information Display Button Area
o Select a channel. Use the <Seek Mode> (see page 36) to change the channel tuning sequence.
1 ; Switches between Function buttons to use.

21 AME 22

Preset 3
For TV picture selection and receiver key operations, see <DDX7015/7045 Basic Operations> (see page 8). The information display is cleared automatically after approximately 5 seconds. Also, the information can be displayed automatically when it is updated (see page 74).

P r e s e t 3 25

a Selects the Auto Memory mode. (see page 36 for the <Auto Memory>)

Information screen

J a z z E n C l a v e3

The category list appears. Category Selection screen

CH 1 6

Channel Name:

S I R3 US I

cat.HITS 0 c a t. RO C K 1
1 Tunes in a channel. 2 Scrolls the list. 3 Returns to the Category Selection screen. 4 Returns to the SIRIUS Tuner Menu.

Artist Name:

S o n g Ti t l e :
c a t. C T RY 2 cat.R&B 3

4 Select a channel

Can c e l

En t e r

c a t. JA Z Z 5
1 Enters a channel number. 2 Returns to the SIRIUS Tuner Menu. 3 Tunes in a channel when you enter is number.
1 Selects a category. 2 Scrolls the list. 3 Returns to the SIRIUS Tuner Menu.
The selected channel is tuned.

3 Enter a channel number

1 Displays the information (such as Channel Name, Category Name, Artist Name, Song Title, and Composer). 2 Scrolls the information display. 3 Returns to the SIRIUS Tuner Menu.

Channel Memory

Stores the current receiving channel in memory. 1 Select a channel you wish to store in memory 4 Tuning

2 Store in memory

40 English

English 41

HD Radio Control
HD Radio Control <North American sales only> (with the optional accessory HD Radio
Various control screens appear in the HD Radio Source mode.

tuner connected only)

The HD Radio Control Panel is displayed in a floating position of the selected picture. 1 Switches the source. 2 Switches the band (HD FM1/2/3, HD AM). 3 Tunes in a station. 4 Switches the Seek mode. (see page 44 for the <Seek Mode>)
Displaying the HD Radio Control screen
You can tune in a station using various functions. 5 Calls the HD Radio Menu. 6 Calls the Sound Effects Menu. (see page 84) 7 Displays the Source Select screen. (see page 55) 8 Calls the Setup Menu. (see page 57) HD Radio Control screen 9 Switches to the HD FM1/2/3 band. p Switches to the HD AM band.

HD 5 a d i o R

162.550 MHz

SRC WBT

52 English

English 53

Character Entry

How To Use the Character Entry screen
When you select the Set Disc Name mode or others, the following screen appears for character entry.

Character Entry screen

Source Select
The source you wish to listen to can be selected quickly.
Displaying the Control screen

KENWOOD

b i p w

c j q x

d k r y

e l s z

Press this key several times unit the Control screen appears. Control screen
1 Shifts the cursor. 2 Enters a space. If you erase a character, locate the cursor on it and touch this button. 3 Enters characters. 4 Scrolls up or down the character button display. 5 Exits the Character Entry mode and returns to the previous screen.
You can enter characters only after you have applied the parking brake.

Title 1 Chap KENWOOD

T0:05:20
The Source Select screen can be displayed from the control screen of any source.
Displaying the Source Select screen

1 Select the source.

2 Returns to the Control screen previously displayed.
Continue to touch until the Source Select screen appears. Source Select screen

S TA N D B Y

DVD VIDEO CD CH

54 English

English 55
Adjusting the Monitor Display Position and Quality
You can adjust the position and picture quality of the monitor.

Setup Menu

You can set up various receiver parameters.
Displaying the Screen Control screen
You can adjust the picture quality using the following keys. 1 Brightness Control Disabled if the Auto Dimmer is On. 2 Tint Control Displayed for an NTSC system image on TV or Video. Screen Control screen 3 Color Control Displayed on the TV and Video screen only. 4 Black Level Adjustment
Press this key several times until the Control screen appeaars. Control screen

5 Contrast Control

6 Displays the Adjust Monitor Position screen. (see <Displaying the Tilt Control screen>, page 56) 7 Returns to the previous screen.
The Screen Control screen is displayed only when you have applied the parking brake.
You can call the same Setup Menu for the Control screen of each source.
Displaying the Tilt Control screen
You can set the monitor tilt. 8 Monitor Tilt Adjustment 9 The monitor fully closes.
Displaying the Setup Menu screen
1 Scrolls the Setup Menu.
2 Calls each Setup Menu. 3 Recalls the previous Setup Menu. 4 Calls the Sound Effects Menu. (see page 84)
p Returns to the Screen Control screen. q Returns to the previous screen.

Audio Control

You can adjust the front and rear and right and left audio balance.
Displaying the Audio Control 1 screen

Au d i o Co n t r o l

2 Calls the Setup Menu. (see page 57) 3 Calls the Sound Effects Menu.

Control screen

Audio Control 1 screen
4 Adjusts the right and left volume balance.
F r o n5 t F FAD F BAL R R
5 Adjusts the front and rear volume balance. 6 Adjusts the volume of the present source based on the difference level of original volume.
If you have increased the volume first, then reduced it using the "Vol. Offset", the big sound may suddenly be generated when you switch to another source.

SUB R 5 Rear

You can display the same Sound Effects Menu on the Control screen of any source.

Vo l. O f f s e t -15

Aud i o Con t r o l 1
7 Adjusts the subwoofer volume. (with the optional accessory DSP unit connected only) 8 Turns the Loudess contol function On or Off. (Does not appear when the optional accessory DSP unit is connected.) If turned "On", high and low tones are automatically enhanced during low volume. ( On) 9 Displays the Audio Control 2 screen.
Displaying the Sound Effects Menu screen
1 Calls the Sound Effects Menu.
Displaying the Audio Control 2 screen
p Adjusts the bass boost of the B.M.S power amplifier (optional accessory).
You may not set some models of power amp boost to "+18". See the catalog or instruction manual of power amplifier.
2 Calls the Setup Menu. (see page 57) 3 Returns to the Control screen of the previous source.

Sound Effects screen

Aud i o
Au d i o Co n t r o l Equa l i z e r Zone C on t r o l
Your setup on the <Sound Effects Menu> is adjusted automatically according to your <Audio Set Up> (see page 58) on the Setup menu. We recommend you to complete the <Audio Set Up> first, then set up the <Sound Effects Menu>. Displayed items vary depending on the optional accessory connected.

Audio Control 2 screen

Menu BMS AMP Bass 10 Flat BMS AMP FREQ Normal 11
q Set the center frequency of bass boost you have set for the "Amp Bass". If you set it to "Low", the center frequency is dropped for 20 to 30%.

Radio reception is poor. The car antenna is not extended. The antenna control wire is not connected. Pull the antenna out all the way. Connect the wire correctly, referring to the section on <INSTALLATION MANUAL>.
The memory is erased when the ignition is turned off. The battery wire has not been connected to the proper terminal. The ignition and battery wire are incorrectly connected. The sound/picture skips on a DVD/VCD/CD. The disc is scratched or dirty. Clean the disc, referring to the section on <Disc cleaning> (see page 6). Connect the wire correctly, referring to the section on <INSTALLATION MANUAL>. Connect the wire correctly, referring to the section on <INSTALLATION MANUAL>.
A track will not play. The screen is dark. Random play has been selected. The unit is in a location where temperature is low. If the temperature of the monitor unit drops, the screen may appear darker when power is first turned on due to the characteristics of a liquid crystal panel. Wait a while after turning power on for the temperature to rise. Normal brightness will return. Turn off random play.
A VCD cannot be played using menus. The VCD disc being played is not compatible with P.B.C. The subtitle is not displayed. Menu playback is available only with VCD discs recorded with P.B.C.
The screen does not darken when the vehicles lights are turned on. The unit is set to auto dimmer. The illumination wire has not been connected. (If manual dimmer is set) AM/FM radio reception is poor and/or there is noise. The TV antenna and vehicles radio antenna are too close. The remote controller does not operate. The remote control mode selector is not set correctly. Switch the remote control mode selector according to the source you select (see page 12). Separate the two antennas as far as possible. Turn off the main unit. The DVD disc being played does not contain the recording of more than one audio (or subtitle) language. The voice (or subtitle) language cannot be changed when the DVD disc being played does not contain the recording of more than one voice (or subtitle) language. When the unit is set to auto dimmer, it is not linked to the vehicle's light switch. Make proper connections according to <INSTALLATION MANUAL>.
The DVD disc being played does not contain the recording of subtitles. The voice (or subtitle) language cannot be changed.
The subtitle cannot be displayed when the DVD disc being played does not contain the recording of subtitles.

96 English

English 97
The viewing angle cannot be changed. The DVD disc being played does not contain the recording of more than one angle. You are attempting to switch the angle in a DVD section where more than one angle is not recorded. Playback will not start even after a title is selected. A viewing restriction (RATING) has been set for the disc. Check the viewing restriction level (RATING) setting. The viewing angle cannot be changed when the DVD disc being played does not contain the recording of more than one angle. More than one viewing angle may be recorded only in limited sections in a disc.

MP3/WMA source

Cannot play an MP3/WMA. The media is scratched or dirty. Clean the media, referring to the CD cleaning of the section on <About discs> (see page 6).
The sound skips when an MP3/WMA is being played. The media is scratched or dirty. The recording condition is bad. The MP3/WMA track time isnt displayed correctly. -- There are times when it isnt displayed correctly according to the MP3/WMA recording conditions. Clean the media, referring to the CD cleaning of the section on <About discs> (see page 6). Record the media again or use another media.
The voice or subtitle language selected in the initial setting is not played. The DVD disc being played does not contain the recording of the selected voice or subtitle language. Use a DVD disc containing the recording of the selected voice or subtitle language.

Disc soruce

The disc control mode cannot be selected. No wire has been connected to the disc changer input terminal on the unit. Connect the wire to the disc changer input terminal on the unit.
Cant display the ID3 tag information correctly. Record is not made in conformity with the ID3 tag version 1.x. Record in conformity with the ID3 tag version 1.x. Also, the display may be incorrect if an MP3/WMA file uses the ID3 tag v1.x standard and if this standard has been expanded after production of the machine software.
The specified disc does not play, but another one plays instead. The specified CD is quite dirty. The CD is upside-down. The disc is loaded in a different slot from that specified. The disc is severely scratched. The sound skips. Something is touching the disc changer. The CD is scratched or dirty. Remove whatever is touching it. If skipping happens at the same place when the car is stopped, something with the CD is wrong. Clean the CD. Hold Error The display shows that the changer is being played, but no sound can be heard. The computer chip in the unit is not functioning normally. The specified track will not play. Random play or magazine random play has been selected. Turn off random play or magazine random play. Disc Error Track repeat, disc repeat, track scan, disc scan, random play, and magazine random play start by themselves. The setting is not cancelled. The settings for these functions remain on until the setting to off or the disc ejected, even if the power is turned off or the source changed. Region code Error The disc can only be removed within 10 minutes of the ACC switch being turned OFF. If more than 10 minutes has elapsed, turn the ACC switch ON again and press the Eject button. Parental level Error Error Read Error Press the reset button on the unit (see page 4). Mecha Error Clean the CD. Load the CD with the labeled side up. Eject the disc magazine and check the number for the specified disc. Try another disc instead.

The following messages are displayed when certain problems are occurring in your system. Take the recommended actions.
Hot Error The protective circuit in the unit activates when the temperature inside the unit exceeds 60C (140F), stopping all operation. ] Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60C (140F), the disc will start playing again. The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60C (140F), stopping all operation. ] Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60C (140F), the disc will start playing again. The disc player is malfunctioning. ] Eject the disc and try inserting it again. Contact the Kenwood dealer if this indicator continues blinking or the disc cannot be ejected. The unplayable discs is inserted. The disc is upside-down. ] Load the disc with the labeled side up. The disc is quite dirty. ] Clean the disc, referring to the section on <Diac cleaning> (see page 6). The DVD software encoded for other region code. The parental level is set to high levels. The unit is malfunctioning for some reason. ] Press the reset button on the unit. If the "Error ##" code does not disappear, consult your nearest service center.
Cant remove disc. The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF.

98 English

English 99

Specifications

Specifications subject to change without notice.

Monitor Section

Picture size..6.95 inches (diagonal) wide 154.1(W)87.1(H)mm Display system..Transparent TN LCD panel Drive system..TFT active matrix system Number of pixels..336,960 (480H234VRGB) Effective pixels...99.99% Pixel arrangement..RGB striped arrangement Back lighting..Cold Cathode Fluorescent Tube

TV section

Color TV Broadcasting system North American Type...NTSC South American Type..NTSC/PAL-M Receivable channels: VHF..2~13ch Receivable channels: UHF..14~69ch Channel selection system.PLL frequency synthesizer system IF signal detection system..Split carrier system Antenna input..4ch diversity (75 /3.5 miniplug)
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.
KENWOOD CORPORATION 2967-3, ISHIKAWA-CHO, HACHIOJI-SHI TOKYO, JAPAN KENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS N0.21 CFR 1040. 10, CHAPTER 1, SUBCHAPTER J.

DVD Section

D/A Converter..24Bit A/D Converter..20Bit Decorder..Linear PCM/Dolby Pro Logic II/Dolby digital/ dts/MLP/MP3/WMA Wow & Flutter..Below Measurable Limit Frequency response (Sampling frequency;192k).20~88,000Hz (Sampling frequency;176.4k)..20~80,000Hz (Sampling frequency;96k)..20~44,000Hz (Sampling frequency;88.2k)..20~40,000Hz (Sampling frequency;48k)..20~22,000Hz (Sampling frequency;44.1k)..20~20,000Hz Total harmonic distortion (1k)..0.003% Signal to Noise ratio..100dB (DVD-Audio 192k) Dynamic range..100dB (DVD-Audio 192k) DISC Format.DVD-Audio/DVD-Video/VIDEO-CD/CD-DA Sampling frequency..44.1kHz/48kHz, 88.2kHz/96kHz, 176.4kHz/192kHz Quantifying bit number..16/20/24bit