*3357*

DX36 M / MX32 / MX62 Bedienungsanleitung Operating instructions Mode demploi Manual de instrucciones

222 222

<Keines>
Bolzensetzgert DX36M / DX36M Fastening Tool / Appareil de scellement DX36M / Herramienta de fijacin DX36M
Nagelmagazin MX32 M, MX62 / Fastener magazine MX32, MX62 / Chargeurs de clous MX32, MX62 / Cargador de clavos MX32, MX62
Awarded the British Standards Institute Kit Mark BS 4078 Part 2
Technische Daten Leistung: Gewicht: Gertelnge: Kartusche: Technical data Performance: Weight: Tool length: Power load: Donnes techniques Rendement: Poids: Longueur: Cartouches: Datos tcnicos Aplicacin: Peso: Longitud: Cartucho: 2
Fr Nagelbefestigungen auf Beton und Stahl 2,4 kg 390 mm 6,8/11M in Magazinstreifen zu je 10 Kartuschen For fastenings to concrete and steel 2.4 kg 390 mm 6.8/11M in cartridge in magazines strips of 10 Pour clouages sur bton et acier 2,4 kg 390 mm 6,8/11M en chargeurs de 10 cartouches Fijaciones de clavos sobre hormign y acero 2,4 kg 390 mm 6,8/11M en peines de 10 cartuchos
Technische Daten Gewicht: Magazinkapazitt: Nagellnge: Technical data Weight: Magazine capacity: Fastener length: Donnes techniques Poids: Capacit du chargeur: Longueur de clous: Datos tcnicos Peso: Capacidad del cargador: Longitud de clavos:
MX32 0,8 kg 10 Stck max. 32 mm MX32 0.8 kg 10 fasteners max. 32 mm MX32 0,8 kg 10 clous max. 32 mm MX32 0,8 kg 10 clavos mx. 32 mm
MX62 1,3 kg 10 Stck max. 62 mm MX62 1.3 kg 10 fasteners max. 62 mm MX62 1,3 kg 10 clous max. 62 mm MX62 1,3 kg 10 clavos mx. 32 mm

Technical description

The DX36M is a tool which drives nails and threaded studs into concrete and steel. The DX36Mworks on the piston principle which gives the assurance of an optimum of operator safety and fastening reliability. The cartridges are transported automatically for faster and more economical fastening. In addition, the DX36M can also be equipped with a fastener magazine. Depending on the required length of nail, the MX32 for nails up to 32 mm long or the MX62 for nails up to 62 mm long can be used. As for all Hilti DX fastening tools, the DX36M, the fasteners and the cartridges have been designed for each other as a technical system. This means that fastening with this tool will only be quick, accurate and troublefree if the fasteners and cartridges designed specifically for this tool are used. Fastening recommendations drawn up by Hilti are only valid if this technical system is used. The recommended maximum fastening rate is 600 fastenings per hour. This tool is not approved for use in explosive atmospheres. This fastener magazine has been designed as an accessory for the DX36M. It greatly increases the fastening speed and ease of operation of the DX36M. lt is a great advantage when used for repetitive fastenings of all kinds 9. Always inspect tool for proper operation before using. Do not use a tool that is incomplete or does not operate properly. 10. Keep arms flexed when operating tool (do not stiff arm). If you feel discomfort, discontinue use. 11. Always hold tool perpendicular to work surface and base material when making fastening. 12. Always use genuine Hilti fasteners, cartridges and spare parts, or those of equivalent quality. 13. Do not attempt to pry cartridge from cartridge strip or from tool. 14. Always do the following if cartridge misfires or fails to ignite: s Keep tool against work surface for 30 seconds. s If cartridge still does not ignite, withdraw tool from work surface, taking care that tool is not pointed at user or bystanders. s Cycle the tool so that the next cartridge is transported. Use up the remaining cartridges in the strip; remove used cartridge strip and dispose of it in such a way that it can neither be used again nor misused. 15. Never fasten through an existing hole, except when otherwise recommended by Hilti, e. g. DX-Kwik. 16. Always keep tool and cartridges locked in a container and in a safe place when not in use. 17. Do not make fastenings in an explosive or flammable atmosphere, except when tool is approved for such use. 18. Always consult application guidelines. 19. Make sure that no one stands behind/below fastening location when making fastenings 20. Do not disassemble tool when it is hot. 21. Never exceed the recommended setting frequency (number of fastenings per hour). 22. Always remove the cartridge strip during work breaks (< 30 seconds).

Safety precautions

Failure to follow these precautions could result in personal injury. ! v Warnings 1. Never use this tool unless you have received proper instruction on its safe use. For assistance, contact your local Hilti sales representative. 2. Always use this tool in strict accordance with the operating instructions and always keep them with the tool. 3. Do not point the tool at yourself or any bystander. 4. Never cock the tool against your hand or other part of your body. 5. Operator and bystanders must wear appropriate eyewear and hard hats while tool is in use. Safety precautions 6. Always use the stabilizer/guard whenever possible. 7. Never leave a loaded tool unattended. Always unload the tool before any cleaning or maintenance work, before remedying any defects or malfunctioning, before storing the tool after finishing work, before work breaks and before changing parts. 8. Wear ear protection when working in confined areas. 4
General notes 23. Never re-drive fasteners. 24. Observe the relevant national regulations, especially those regarding accident prevention. Through-shot and ricochet prevention: The piston principle employed results in low fastener velocity and dissipation of excess driving power. Contact pressure safety device: The pressure required to overcome the cocking force and movement prevents a loaded tool from being fired if it is not pressed against a firm work surface. The tool can only be fired if the contact pressure safety device is pressed to over-come a movement of 16 mm and a minimum force of 110 N.
Handhabung Standardgert / Handling of standard tool / Maniement de lappareil standard / Manejo de la herramienta estndar
Gerteleistung einstellen durch Drehen des Regulierbolzens. 1 = min. Leistung 3 = max. Leistung
Einsatz ganz nach vorne ziehen und wieder zurckstossen. Hinweis: Lsst sich der Einsatz schwer ausziehen, Schlitz mit Hilti Spray leicht einsprhen und Einsatz einige Male hin- und herschieben. Pull out the barrel assembly fully and push it back again. Note: If the barrel assembly is stiff, spray the slot sparingly with Hilti lubricant and pull out and push back the barrel assembly several times. Tirer fond l'ensemble canon vers l'avant, puis le repousser fond. Nota: Si l'ensemble canon coulisse difficilement, lubrifier lgrement la rainure avec un peu de spray Hilti, puis faire coulisser l'ensemble canon plusieurs fois dans les 2 sens. Mover el conjunto completamente hacia adelante y empujarlo atrs otra vez. Nota: Si se mueve con dificultad, lubricar la ranura levemente con el spray Hilti y mover el conjunto varias veces hacia adelante y hacia atrs

Confirmation of CIP testing
The Hilti DX 36M has been system and type tested. As a result, the tool bears the PTB approval mark of square shape showing approval number S 801. In this way, Hilti guarantees compliance with the approved type. Unacceptable/inadmissible defects, deficiencies, etc. that are determined during use of the tool must be reported to the manager responsible at the approval authority (PTB) and to the Office of the Permanent International Commission (C.I.P.).
Noise information as per German legislation (3. GSGV dated January 18, 1991) Lrminformation nach der 3. GSGV vom 18. Januar 1991
Als Gertekennwerte werden der Schalleistungspegel LWA, 1S nach 1 (2) 1b) sowie wegen der je nach Anwendung unterschiedlichen Arbeitspltze der Messflchenschalldruckpegel L pA, Imax in 1 m Abstand nach 1 (2) 1e) angegeben, zustzlich der arbeitsplatzbezogene Emissionswert nach der Messnorm. Betriebszustand und Aufstellbedingungen strkste bestimmungsgemss zu verwendende Ladung mit angepasstem Setzbolzen, Auslsung auf Betonblock senkrecht nach unten sowie die Messtechnik entsprechend DIN 45635, Teil 34 Geruschmessung an Maschinen Luftschallemission, Hllflchen-Verfahren Bolzensetzwerkzeuge. Lrminformationen bei roter Kartusche und Maximalleistung: 1b) Schalleistungspegel LWA,1S = 105 dB (A) arbeitsplatzbezogener Emissionswert LpA, Imax = 100 dB (A) (gemessen am Ort der Ohren der Bedienungsperson) 1e) Messflchenschalldruckpegel LpA, Imax = 92 dB (A) Abweichende Arbeitsbedingungen knnen zu anderen Emissionswerten fhren. The noise (power) level LWA, 1S as per 1 (2) 1b) applicable to the tool and, due to different workplaces depending on the application for which the tool is used, also the noise (pressure) level LpA, Imax at the measurement surface of 1 metre as per 1 (2) 1e), are given in addition to the workplace related noise emission value in accordance with the noise measurement standard. Operating conditions and circumstances of use: most powerful cartridge power load in accordance with instructions for use with suitable nail or stud fired vertically downwards into a steel plate and in accordance with the means of measurement DIN 45635, part 34 Measurement of the noise emitted by powder-actuated fastening tools. Noise information With red cartridge and maximum power setting 4 = 105 dB (A) 1b) Noise (power) level LWA workplace relevant emission value LpA, Imax = 100 dB (A) (measured at operator ear level) 1e) Noise (pressure) level LpA, Imax = 92 dB (A) Variations in operating conditions may cause deviations from these noise emission values.