English version

LW050v2/LW050v2UK Sweex Wireless Broadband Router 54 Mbps

Introduction

First of all, many thanks for purchasing this Sweex Wireless Broadband Router 54 Mbps. The Sweex Wireless Broadband Router 54 Mbps enables you to share a broadband Internet connection and to set up your own wireless network. To ensure this product operates correctly, we advise you to carefully read this manual first. If despite this manual you still experience problems during installation or operation of this product, go to www.sweex.com and look under the heading service & support. In order to fully enjoy the Sweex Wireless Broadband Router 54 Mbps, it is important to observe a number of things: not expose the Sweex Wireless Broadband Router 54 Mbps to extreme temperatures. Do Do not place the device in direct sunlight or in the direct vicinity of heating elements. not use the Sweex Wireless Broadband Router 54 Mbps in extremely dusty or moist surroundings. Do Protect the device against powerful shocks or jolts - they may damage the internal electronics. Never attempt to open the device yourself - it will cause the warranty to lapse.

Contents of the box

Prior to using the Sweex Wireless Broadband Router 54 Mbps, check if all required parts are present. The following parts must be present in the box: Wireless broadband router 54 Mbps Antenna Power supply adaptor RJ-45 UTP Ethernet network cable CD-ROM with manual and Panda Anti-virus trial software If one of the above parts is missing, please contact the shop or supplier.

Specifications

Supports: IEEE 803.3 and IEEE 803.3u Supports: IEEE 802.11b, IEEE 802.11g Maximum wireless data transfer speed: 54Mbps Supports: DHCP (dynamic IP), PPTP, Static IP, PPPoE, L2TP x WAN, 4 x LAN RJ-45 UTP ports 1 Supports: WEP/WPA./WPA2/802.1X data encryption Built-in Firewall and Port Forwarding Removable reverse SMA Antenna 5 dBi to 3 x Extended Range 2 Supports: VPN pass through Web-based configuration operating system dependent Not

Front view

Status Status Off Power Lit Lit System Blinking Off Off Link/Act WAN and 1 to 4 Lit Blinking Off WLAN Blinking
Meaning The router is switched off The router is switched on The router is starting up The router is operating correctly The router has a hardware error No device is connected to this port A computer or other network device is connected to this port There is data traffic between the router and the connected device The wireless part is switched off The wireless part is active

Rear view

Antenna with reverse SMA connector. Reset button to return to the factory settings port for connecting a modem by means of a RJ-45 UTP Ethernet network cable. WAN ports 1, 2, 3 and 4 for connecting computers by means of an RJ-45 UTP Ethernet network cable. LAN Power connector for connecting the power adaptor.
Connecting the Sweex Wireless Broadband Router 54 Mbps
1. onnect the power adaptor (included) to the rear of the router and the mains socket. The light next to Power is lit. In the event the LED is not C lit, check the connections of the power adaptor to the router and the mains socket. 2. witch on the computer and connect it to the rear of the modem using a network cable (RJ-45 UTP). You can select any of the ports 1, 2, 3 and 4. S The corresponding light at the front will be lit. In the event the light fails to light up, check whether the network cable is properly connected to the computer and the router. 3. witch on the modem* again. Note: Here we do not refer to the Sweex router. Connect the modem to the rear of the router using a network S cable (RJ-45 UTP). Do this via the WAN port The WAN light at the front of the router will light up. In the event the light fails to light up, check whether the network cable is properly connected to the router and the modem. *In order to use the Sweex Wireless Broadband Router 54 Mbps you need an active Internet connection, which is established through a modem. This modem is usually supplied by the provider.

Configuring the computer to connect to the router
Windows XP In the bottom left of your screen, go to Start Control Panel Then go to Network and Internet Connections. Open Network Connections. Or, if the Windows classic style is used: Start Settings Network Connections. Right-click LAN Connection or Wireless Network Connection and select Properties. The following screen appears:
Under the tab General select TCP/IP and click Properties.
Select the options Obtain an IP address automatically and Obtain DNS server address automatically. Confirm the settings by clicking OK. The network settings for Windows XP have now been configured correctly. The correct settings for the Internet browser will be discussed later in this manual.
Windows 2000 In the bottom left of your screen, go to Start Control Panel. Then go to Network and Internet Connections. Open Network Connections. Or, if the Windows classic style is used: Start Settings Network Connections. Right-click LAN Connection or Wireless Network Connection and select Properties. The following screen appears:
Now select Internet Protocol (TCP/IP) and click Properties.
Select the options Obtain an IP address automatically and Obtain DNS server address automatically. Click OK twice. The network settings for Windows 2000 have now been configured correctly. The correct settings for the Internet browser will be discussed later in this manual.
Windows 98SE Go to Start, Settings, Control Panel and click Network.

Select the line TCP/IP

which corresponds to your (wireless) network card and click Properties.
Under the tab IP Address, select the option Obtain an IP address automatically.
Under the tab Gateway, the list of Installed gateways must be empty. If so required, select each gateway and click Remove.
Under the tab DNS Configuration, select the option Disable DNS. Click OK twice. The network settings for Windows 98SE have now been configured correctly. Now continue with the correct settings for the Internet browser below.
Internet browser settings for Windows 98SE, 2000 and XP
1.n order to access the router, the browser settings must be correct. This is easy to check by starting up Internet Explorer and selecting Tools I from the menu bar and then selecting the option Internet Options. 2.n this window, go to Connections and select Never dial a connection or remove all connections listed in the field above. I 3. t the bottom, click LAN Settings, remove all ticks and click OK. A 4. estart the browser to activate the settings. R

Setting the wireless network
How does it work? In order to create a wireless network, you need a wireless router, wireless modem or access point. The wireless router, modem or access point transmits the wireless network. The name of this network, also referred to as SSID, depends on your wireless router, modem or access point and often differs per model or brand. You can often determine the name yourself and thus recognise your own wireless network. Protection You could compare a wireless network to radio signals. However, the range of a wireless network at home is not as big. Your home wireless network often has a range of 20 to 30 metres. This means that neighbours and passers-by too can make use of your network. As a result they can get away with surfing on your Internet connection, and they may gain access to your shared folders and files on your network. That is why it is recommended to secure your wireless network. This protection is set up on the device transmitting the network. In most cases that is the wireless router, modem or access point. By adding a WEP or WPA protection code, you secure the network. This code is also referred to as the network key. Enter this code on each computer that wants to connect to that secured network. You can only be part of that network if you enter this code. If you did not enter the network key into the router or modem yourself, ask the installer, manufacturer, supplier or provider for this code.
Connecting the computer to the wireless network
In the bottom left of your screen, go to Start Control Panel. Then go to Network and Internet Connections. Open Network Connections. Or, if the Windows classic style is used: Start Settings Network Connections. Right-click LAN Connection or Wireless Network Connection and select View Available Wireless Networks.
Always click Refresh network list top left in this window first, to obtain the most recent listing. Select the name (also referred to as SSID) Sweex LW050v2 by clicking it once. Now click Connect. If it has successfully connected to the wireless network, the notification Connected appears after a couple of seconds. You now have an active wireless network. If you receive a notification saying the wireless connection cannot be configured because it is managed by another programme, disable this software and start again. We recommend securing the wireless part of the router. How to do this is described further down in this manual. Once secured, the network will show as Sweex LW050v2 with a message below detailing Security-enabled wireless network. When connecting to this secured network, you will be prompted for the Network key. If the network key you have entered is incorrect, a notification saying "Limited or no network connection" appears after a couple of seconds. Your wireless connection is not satisfactory. Re-connect to the wireless network and check the network key. If you change something in the wireless settings of the router causing you to lose the wireless connection, then complete these steps again.

Accessing the router (Login)
Open your web browser. In this example we use Internet Explorer.
The default router IP address is: 192.168.50.1 An IP address is a unique number required by each network device, including a computer or router, in order to be active within that network. Without an IP address you are unable to make connections within a network. Type the router IP address in the browser address bar. You can now access the router.
The router login screen appears. Fill out the login name and the corresponding password. The standard login is sweex and the corresponding password is mysweex. If this login screen fails to appear, recheck the settings of your Internet browser as described above. Also check the IP address of your computer. In this IP address, only the digits after the last dot may deviate from the IP address of the router (e.g.: 192.168.200.xxx).
Where to find the IP address of the computer?
Win2000/WinXP: Click Start - Run - Type cmd - press "Enter. In the black window, type ipconfig - press "Enter and your IP address is displayed. Win98/Me: Click Start - Run -Type winipcfg - press "Enter. In the window, select your network adaptor. (Usually NOT the ppp adaptor) and your IP address is displayed.
Once logged in, the status screen of the router appears.
This screen displays the current Internet connection and a variety of system information.
Setting the Internet Provider (ISP)
Prior to setting the provider, make sure that the Internet connection is active without the Sweex Breedband Router. If the modem without the router does not have an Internet connection, setting the router would be pointless. After all, the modem establishes the Internet connection and the Sweex Breedband Router forwards this existing Internet connection to one or more computers in your network. A total of 6 different settings are possible. We have listed these together with instructions on how to enter these. In order to find out which settings correspond to your provider, you can consult the list with providers further down in this manual. The list consists of providers and corresponding subscriptions. The applicable settings are listed for each subscription form. In the event that your subscription is not listed, consult your Internet provider for the router settings which correspond to your subscription. These settings need to be configured in your router only once. Regardless of the number of computers you connect to the router, the following settings only need to be done on one computer. That is because the settings are not stored on the computer, but on the router.
Setting 1 DHCP without hostname
1. eft in the column, click Network". Now click WAN. L

2. nder WAN Connection Type select Dynamic IP. This setting is for providers who use a DHCP connection. U 3. lick Save to save the settings. C In order to check whether the Internet connection has been set up successfully, go to the status screen by clicking Status left in the column. The WAN section will display your Internet IP address. It can sometimes take up to 1 minute for this IP address to appear. You have now completed the configuration and are ready to surf the Internet. If after 1 minute your IP address continues to show as 0.0.0.0, check your settings again and complete the following steps: 1. witch off the router and the modem. S 2. isconnect the network cable between the router and the modem at the WAN port. D 3. witch on the router and wait until it is fully started up. S 4. witch on the modem and wait until it is fully started up and until all the correct lights are lit. S 5. econnect the network cable between the modem and the router via the WAN port of the router. R 6. onnect the router via 192.168.50.1 and check your Internet connection in the status screen. C
Setting 2 DHCP with hostname
Important: when configuring the router, always use the computer with which you were connected to the Internet prior to connecting the router. 1. eft in the column, click Network". Now click WAN. L
2. nder WAN Connection Type select Dynamic IP. This setting is for providers who use a DHCP connection. U 3. nder Hostname enter the hostname you received from your provider. U 4. lick Save to save the settings. C L 5. eft in the column, click MAC Clone".
6.n order to enter the MAC address of your computer into the router, click Clone MAC Address and then Save to save the settings. I 7. lick OK to confirm. C In order to check whether the Internet connection has been set up successfully, go to the status screen by clicking Status left in the column. The WAN section will display your Internet IP address. It can sometimes take up to 1 minute for this IP address to appear. You have now completed the configuration and are ready to surf the Internet.

If after 1 minute your IP address continues to show as 0.0.0.0, check your settings again and complete the following steps: 1. witch off the router and the modem. S 2. isconnect the network cable between the router and the modem at the WAN port. D 3. witch on the router and wait until it is fully started up. S 4. witch on the modem and wait until it is fully started up and until all the correct lights are lit. S 5. econnect the network cable between the modem and the router via the WAN port of the router. R 6. onnect the router via 192.168.50.1 and check your Internet connection in the status screen. C

Setting 3 PPPoE

2. nder WAN Connection Type select PPPoE. This setting is for providers who use a PPPoE connection. U 3. nder User Name enter the user name you received from your provider. U 4. nder Password, enter the corresponding passport. U C 5. lick Save to save the settings. In order to check whether the Internet connection has been set up successfully, go to the status screen by clicking Status left in the column. The WAN section will display your Internet IP address. It can sometimes take up to 1 minute for this IP address to appear. You have now completed the configuration and are ready to surf the Internet. If after 1 minute your IP address continues to show as 0.0.0.0, check your settings again and complete the following steps: 1. witch off the router and the modem. S 2. isconnect the network cable between the router and the modem at the WAN port. D 3. witch on the router and wait until it is fully started up. S 4. witch on the modem and wait until it is fully started up and until all the correct lights are lit. S 5. econnect the network cable between the modem and the router via the WAN port of the router. R 6. onnect the router via 192.168.50.1 and check your Internet connection in the status screen. C

Setting 4 PPTP

2. nder WAN Connection Type select PPTP. This setting is for providers who use a PPTP or KPN Mxstream connection. U 3. nder User Name enter the user name you received from your provider. U U 4. nder Password, enter the corresponding passport. C 5. lick Save to save the settings. 6. lick Connect to make the Internet connection. Next to this button, the message Connected will appear and your Internet IP address will C be displayed under Internet IP Address. It can sometimes take up to 1 minute for this to be shown. You have now completed the configuration and are ready to surf the Internet. If after 1 minute the router continues to show as Disconnected, check your settings again and complete the following steps: 1. witch off the router and the modem. S 2. isconnect the network cable between the router and the modem at the WAN port. D 3. witch on the router and wait until it is fully started up. S 4. witch on the modem and wait until it is fully started up and until all the correct lights are lit. S 5. econnect the network cable between the modem and the router via the WAN port of the router. R 6. onnect the router via 192.168.50.1 and check your Internet connection in the status screen by clicking Status left in the column. The WAN C section will display your Internet IP address.

Setting 5 L2TP

2. nder WAN Connection Type select L2TP. This setting is for providers who use an L2TP connection. U 3. nder User Name enter the user name you received from your provider. U U 4. nder Password, enter the corresponding passport. C 5. lick Save to save the settings. 6. lick Connect to make the Internet connection. Next to this button the message Connected appears and your Internet IP address will C be displayed under Internet IP Address. It can sometimes take up to 1 minute for it to be shown. You have now completed the configuration and are ready to surf the Internet. If after 1 minute the router continues to show as Disconnected, check your settings again and complete the following steps: 1. witch off the router and the modem. S 2. isconnect the network cable between the router and the modem at the WAN port. D 3. witch on the router and wait until it is fully started up. S 4. witch on the modem and wait until it is fully started up and until all the correct lights are lit. S 5. econnect the network cable between the modem and the router via the WAN port of the router. R 6. onnect the router via 192.168.50.1 and check your Internet connection in the status screen by clicking Status left in the column. The WAN C section will display your Internet IP address.

Setting 6 Static IP

2. nder WAN Connection Type select Static IP. This setting is for providers who use a fixed Static IP address. U 3. nder IP Address, enter the IP address you received from your provider. U 4. lso enter your Subnet Mask, Gateway, Primary DNS and possibly your Secundary DNS values. A 5. lick Save to save the settings. C In order to check whether the Internet connection has been set up successfully, go to the status screen by clicking Status left in the column. The WAN section will display your Internet IP address. It can sometimes take up to 1 minute for this IP address to appear. You have now completed the configuration and are ready to surf the Internet. If after 1 minute your IP address continues to show as 0.0.0.0, check your settings again and complete the following steps: 1. witch off the router and the modem. S 2. isconnect the network cable between the router and the modem at the WAN port. D 3. witch on the router and wait until it is fully started up. S 4. witch on the modem and wait until it is fully started up and until all the correct lights are lit. S 5. econnect the network cable between the modem and the router via the WAN port of the router. R 6. onnect the router via 192.168.50.1 and check your Internet connection in the status screen. C

Wireless settings and security
We always recommend entering these settings with a computer connected to the Sweex Breedband Router by means of a cable. This is because you will lose the wireless connection with the Sweex Breedband Router while storing these settings. Left in the column, click Wireless".
The default SSID is Sweex LW050v2. We recommend not changing this so you can always recognise the router. Here you can also find other options such as Channel and Mode. We again recommend maintaining the default values. You can enable or disable the wireless part by means of Enable Wireless Router Radio. This feature is enabled by default.
Securing the wireless part
Complete the following steps for setting WEP security: 1. ick Enable Wireless Security T 2. nder Security Type select WEP. U 3. nder Key Type select 64bit. U 4. nder WEP Key, enter the network key. In our example we use network key 1020304050. U When using 64-bit encryption you can create your own 10-digit code, 128 bits require 26 digits. 5. lick Save to save the settings. C 6. small window appears. Click OK to restart the router. A The router is now secured. Reconnect your wireless computer. Complete the following steps for setting WPA security: 1. ick Enable Wireless Security T 2. nder Security Type select WPA-PSK/WPA2-PSK. U
3. nder PSK Passphrase, enter your network key. You can create your own and it may contain 8 to 63 numbers and letters. U 4. lick Save to save the settings. C 5. small window appears. Click OK to restart the router. A The router is now secured. Reconnect your wireless computer.
Opening ports in the router (Forwarding and DMZ)
The built-in firewall in this router cannot be disabled. However, ports can be opened for programmes and games which require this. We recommend using a fixed IP address for computers for which ports are opened. This is to ensure that these computers always use the same IP address as registered in the router. The router may assign a different IP address to the computer so that the forwarding or DMZ command no longer applies to that computer. By clicking Forwarding left in the column the port settings can be changed.
1. nder Service Port, enter the port or the range of ports you want to open. For example: 3500-3600 opens all ports within that range. U 2. nder IP Address, enter the IP address of the computer for which you want to open these ports. U 3. ick Enable to activate this line. T 4. lick Save to save the settings. C You can complete 16 lines. Click Next to show lines 9 16.
In some instances, or when a game console is used, you may opt to place a computer or game console entirely outside the firewall. This can be done in the so-called demilitarized zone (DMZ). This option can be found in the main screen of the port settings (Port Forwarding) under (Advanced.) Note however, you no longer take advantage of the protection offered by the firewall of the router. All ports to the computer placed in the DMZ are open. Only a single computer can be placed in the DMZ. Left in the column, click Forwarding" and then DMZ.

Set Current DMZ Status to Enable and under DMZ Host IP Address, enter the IP address of the computer which you want to place in the DMZ. Click Save to save the settings.
How to assign a fixed IP address to a computer
This is only required for computers for which you want to open ports by means of the function Forwarding or DMZ. Complete the steps in chapter Configuring the computer to connect to the router. Instead of selecting Obtain an IP address automatically (Obtain an IP address automatically) you select Use the following IP address (Use the following IP address). The IP address in our example is as follows (192.168.50.xxx). The final number you enter must be unique to your network. We recommend using a number ranging from 150 to 200. Thus an IP address could be (192.168.50.150). A subsequent computer would then be assigned (192.168.50.151) etc. For Subnetmask (Subnetmask) you enter: 255.255.255.0 Both under Default gateway (Default gateway) and under Preferred DNS-server (Preferred DNS-server) you enter the IP address with which you log into the router. In our example: 192.168.50.1 Under Alternative DNS-server (Alternative-DNS-server), you can leave the field blank. Click OK twice to save the settings and to close the window.

LAN settings

The network settings of the router can be changed as follows. Left in the column, click Network".
Under IP Address, the IP address of the router (192.168.50.1) is stated. Changing the number here, changes the IP address of the router. Note! When you assign the router a new IP address, the Start IP and End IP of the DHCP server must be changed to reflect that range. Click Save to save the settings.

Changing the password

The standard login of the Sweex Breedband Router can be changed by clicking System Tools and then Password, left in the column.
In order to change the user name and password settings, enter your current user name under Old User Name and your current password under Old Password Subsequently, enter your new user name under New User Name, and your new password under New Password. Confirm by once again entering your new password under Confirm New Password. Click Save to save the settings. A small login window appears. Log in twice, using your new user name and password.
Upgrading the firmware of the router (Firmware)
In order to provide the router with updates, the so-called firmware needs updating. Left in the menu, click System Tools and then Firmware.

Here the firmware of the router can be upgraded. New firmware can be downloaded from the Sweex website under Service en support. If the firmware file is zipped, make sure you select and extract the file first on a location in your computer where you can retrieve it easily. Now click Browse and select the extracted firmware file. In many cases the name of this file will start with Sweex_Firmware_LW050v2. In order to start the firmware upgrade, click Upgrade. Do not interrupt this procedure. This may harm the router. Wait for the upgrade to be completed which is confirmed by a message. The connection between the computer and the router will be briefly interrupted.
Resetting the router to its factory settings
The Sweex Breedband Router can be reset to its factory settings in two different ways. Note! After the reset, all settings which apply to your connection and network need to be reconfigured. After the reset, the router will restart. During start-up, the factory settings are reloaded and the computer will lose connection with the router for around 30 seconds. After this, the router can be accessed via the default IP address (192.168.50.1). Method 1: Switch off the router by disconnecting it from the mains. The reset button is located at the rear of the router. Use a small item to press the button. Press and hold the button while you switch on the router again. After switching on, press and hold the button another 10 seconds. The router will restart. Method 2: Left in the column, click System Tools and then Factory Defaults. Click Restore to start the reset. A message appears, click OK to continue. Additional tips and further explanation to the remaining functions of the router can be found in the English manual on the CD-ROM.

Warranty

All products under the Sweex brand are warranted for a period of three years. We do not grant support or warranties for any software and/or (rechargeable) batteries included. Settlement of guarantee only takes place via the dealer where you have purchased the product in question. The rightful owner has and retains title to all brand names and related rights mentioned in this manual.