(GB) (DE) (FR) (NL)

CARTON CONTENTS KARTONINHALT CONTENU DU CARTON INHOUD

(NO) (FI) (SE) (DK)

KARTONGENS INNHOLD (ES) CONTENIDO DEL CARTON PAKETIN SISLT (PT) LEGENDAS DOS DESENHOS FRPACKNINGENS INNEHLL (IT) DE CARTONE KARTONINDHOLD
Wheel Frame (if applicable) Zum Radgestell gehrende Teile (falls zutreffend) Chariot de transport (s'il y a lieu)
Wielframe (indien van toepassing)
Hjulramme (om relevant) Pyrn runko (jos kytss) Hjulram (dr sdan finns) Hjulstel (hvis relevant) Bastidor de las ruedas (si fuera aplicable) Armao das Rodas (se aplicvel) Telaio ruote (se in dotazione)

Safety Precautions

If not used properly this lawnmower can be dangerous! This lawnmower can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this lawnmower. The operator is responsible for following the warning and safety instructions in this manual and on the lawnmower. Explanation of Symbols on the XL500/XL550 Wipe dirt and grass clippings from the fuel tank filler cap to avoid getting dirt into the fuel tank. - Add fuel BEFORE starting the engine. Never remove the cap of the fuel tank or add fuel while the engine is running or when the engine is hot. - If petrol is spilled, do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until petrol vapours have dissipated. - Never use stale fuel left from last season or fuel which has been stored for long periods. - Replace all fuel tanks and container caps securely. - Move the product away from the fuelling area before starting. - Fuel should be stored in a cool place away from naked flames. - Your carburettor is pre-set. Normally no further adjustment is required. Preparation 1. While using your product always wear substantial footwear and long trousers. 2. The use of ear protection is recommended. 3. Make sure the area to be cut is clear of sticks, stones, bones, wire and debris; they could be thrown by the blade. 4. Before using the machine and after any impact, check for signs of wear or damage and repair as necessary. 5. Replace worn or damaged blades together with their fixings in sets to preserve balance. 6. Have faulty silencers replaced. Use 1. Do not operate the engine in a confined space where exhaust fumes (carbon monoxide) can collect. 2. Use the mower only in daylight or good artificial light. 3. Avoid operating your mower in wet grass, where feasible. 4. Take care in wet grass, you may lose your footing. 5. On slopes, be extra careful of your footing and wear non-slip footwear. 6. Mowing on banks and slopes can be dangerous. Do not mow on banks or steep slopes. 7. Do not walk backwards when mowing, you could trip. Walk never run. 8. Never cut grass by pulling the mower towards you. 9. Release the Operator Presence control to stop the engine before pushing the mower across surfaces other than grass and when transporting the lawnmower to and from the area to be mowed. 10. Never operate the lawnmower with damaged guards or without guards in place. 11. Do not overspeed the engine or alter governor settings. Excessive speed is dangerous and shortens lawnmower life. 12. Keep hands and feet away from the cutting means at all times and especially when switching on the engine. 13. Do not tilt the mower when starting the engine, except if the mower has to be tilted for starting. In this case, do not tilt more than absolutely necessary and lift only the part which is away from the operator. Always ensure that both hands are in the operating position before returning the appliance to the ground. -

Warning

Read the user instructions carefully to make sure you understand all the controls and what they do. Always keep the lawnmower on the ground when mowing. Tilting or lifting the lawnmower may cause stones to be thrown out Keep bystanders away. Do not mow whilst people especially children or pets are in the mowing area
Beware of severing toes or hands. Do not put hands or feet near a rotating blade. Disconnect the spark plug before attempting any maintenance, cleaning or adjustment, or if you are going to leave the lawnmower unattended for any period. Blade continues to rotate after the machine is switched off. Wait until all machine components have completely stopped before touching them.
General 1. Never allow children or people unfamiliar with these instructions to use the mower. Local regulations may restrict the age of the operator. 2. Only use the lawnmower in the manner and for the functions described in these instructions. 3. Never operate the lawnmower when you are tired, ill or under the influence of alcohol, drugs or medicine. 4. The operator or user is responsible for accidents or hazards occurring to other people or their property. Fuel Safety WARNING - Petrol is highly flammable - Wear protective clothing when handling any fuels and lubricants. - Avoid contact with skin. If affected, wash liberally with soap and water. - Store fuel in a cool place in a container specifically designed for the purpose. - Use a fresh, clean, unleaded regular automotive petrol - Use 4-stroke automotive detergent oil. SAE 10W-30 is recommended for general use. - Refuel outdoors only and do not smoke while refuelling.

ENGLISH - 1

14. Never pick up or carry a lawnmower while the engine is running 15. Spark plug lead may be hot - handle with care. 16. Do not attempt any maintenance on your lawnmower when the engine is hot. 17. Release the Operator Presence Control, to stop the engine, and wait until the blade has stopped: - before leaving the mower unattended for any period. 18. Release the Operator Presence Control, to stop the engine, wait until the blade has stopped, disconnect the spark plug lead and wait until the engine has cooled:- before refuelling - before clearing a blockage; - before checking, cleaning or working on the appliance; - if you hit an object. Do not use your lawnmower until you are sure that the entire lawnmower is in a safe operating condition; - if the lawnmower starts to vibrate abnormally. Check immediately. Excessive vibration can cause injury. Maintenance and storage 1. Keep all nuts, bolts and screws tight to be sure the lawnmower is in safe working condition. 2. Replace worn or damaged parts for safety. 3. Only use the replacement blade, blade bolt, spacer and impeller specified for this product. 4. Never store the lawnmower with fuel in the tank inside a building where fumes can reach an open flame or spark. 5. Allow the engine to cool before storing in any enclosure. 6. To reduce fire hazard, keep the engine, muffler and fuel storage area free of grass, leaves or excessive grease. 7. If the fuel tank has to be drained, this should be done outdoors. 8. Be careful during adjustment of the machine to prevent entrapment of the fingers between moving parts and fixed parts of the machine.

Assembly (without wheels)
Fitting the Lower Handle to the Lawnmower 1. Feed the hook (A2) attached to the lower handle (A1) halfway through the centre slot of the guide (A3), in the direction indicated by the arrow (A4). 2. Maintaining the hook (A2) in the centre slot of the guide (A3) turn the lower handle (A1) clockwise through 900 to place both legs of the lower handle in position between the hood brackets (A5). 3. Insert the pins (B1) and secure with the retaining clips (B2). Fitting the Upper Handle to the Lower Handle BEFORE fitting the upper handle to the lower handle, stabilize the lower handle by lifting the hook (C1) to the 'parking' position (C2). 1. Ensure the Choke Control Lever is on the left hand side when viewed from the rear. 2. Align the lower and upper handle (See fig D). Locate the bolts (D1), washers (D2) and secure with the handle knobs (D3). 3. Fit the cables to the handles with the cable ties provided, making sure the cables are not trapped between the upper and lower handles.

Assembly (with wheels)

1. Fit the lower handle (E1) to the deck with the lower handle pin (E2) as illustrated in Fig E. 2. Attach the wheels (F1) to the wheel frame (F2) with the wheel retaining clips (F3) as illustrated in Fig F. 3. Fit the wheel frame (G1) to the deck with the lower handle bolt (G2), small washer (G3), large washer (G4) and locknut (G5) as illustrated in Fig G. 4. Locate the lower telescopic tubes (H1) inside the upper telescopic tubes (H2) and secure with the pin (H3) and retaining clip (H4) as illustrated in Fig H. Fit the Upper Handle to the Lower Handle by following the instructions above in Assembly (without wheels) section.

Handle Position

The handle position can be adjusted using the guide and hook assembly. 1. Lift hook (C1). 2. Position as required: (C2) Parking position (C3) Mowing position
Use a fresh, clean, unleaded regular automotive gasoline Do not fill the fuel tank in an enclosed area, when the engine is hot or while you are smoking or near a naked flame. Thoroughly clean around the fuel tank filler cap before filling, this will help to prevent dirt being introduced into the fuel system. Fuel should be stored in a cool place away from naked flames. Do not fill the tank while the engine is running. Fill the fuel tank through a funnel fitted with a fine filter. Never fill fuel tank completely, only fill to the base of the filler neck. When filling the fuel tank from empty, or when the engine has previously run dry, a minimum of 400cc of fuel must be added (to the level of the line indicated in the diagram) to ensure correct priming of the fuel pump to start the engine. Your carburettor is pre-set. Normally no further adjustment is required.

ENGLISH - 2

Use 4-stroke automotive detergent oil. SAE 10W-30 is recommended for general use. Fill with oil as instructed in your Engine Owners Manual provided with your product.

Starting and Stopping

To 1. 2. 3. 4. Start your Lawnmower Move the handle to the parking position (C2). Connect the spark plug lead. (J). Open the fuel tap (K). Move the Choke control lever to the Choke position (L) when starting from cold, and to the Run position (N) when starting from hot. 5. Pull and firmly hold the Operator Presence Control to the upper handle. 6. Place your right foot firmly on the deck and grasp the top of the lower handle with your left hand. Tilt the trimmer towards you (M). This ensures the product is in a secure position when starting and also prevents an unsightly ring being cut in your lawn. 7. Pull the starting handle gently until you feel a resistance, return the starting handle slowly. 8. Pull the starting handle firmly towards you to its full extent. 9. Allow the engine to reach its full running speed then gently lower the lawnmower to the ground. 10. When the engine has warmed up make sure the choke control lever is in the 'Run' (N) position. To Stop your Lawnmower Blade continues to rotate after the machine has switched off, rotating blades can cause injury. 1. Release the Operator Presence Control. 2. As the engine dies, tilt the lawnmower slightly. This prevents a ring being cut in your lawn. 3. When the engine has stopped, lower the lawnmower to the ground. 4. Put the handle in the Parking position (C2). 5. Close the fuel tap (K)

IMPORTANT

AIR CLEANER
Before any servicing to the underside of your machine, close the fuel tap, let the engine run until it stops, disconnect the spark plug lead and TIP THE MACHINE ON ITS SIDE WITH THE AIR CLEANER UPPERMOST.
Adjusting the cutting height
Adjusting the Cutting Height Never use more than 2 cutting height spacers. Spacers can only be fitted between the blade and the fan and never between blade and the bolt (P). 1. Ensure the Operator Presence Control is released, when the engine has stopped rotating - disconnect the spark plug lead. 2. Close the fuel tap (K). Turn your lawnmower on its side. 3. Remove the blade bolt (P1) and blade (P2) as described in Removing the Blade and Fan. 4. For a Lower Cut - Add spacers (P3) to a maximum of 2. 5. For a Higher Cut - Take spacers (P3) away. 6. Refit the blade as described in Fitting the Blade and Fan.

TIP THIS WAY ONLY

How to Mow 1. Place the handle in the mowing position (C3). 2. Mow twice a week in the growing season. Your lawn will suffer if more than one third of its length is cut at one time. Keep hands and feet away from the blade, a rotating blade cannot be seen. Mowing on banks and slopes can be dangerous. Do not mow on steep slopes. Always keep your feet on flat ground with the mower below you on the slope and with the spark plug uppermost to avoid lubricating oil running into the cylinder. Do not use this mower on slopes which are wet or more than 450 from horizontal. Never push the mower up the slope.
Removing & Fitting the Blade & Fan
WARNING Always handle the blade with care - sharp edges could cause injury. USE GLOVES Spark plug lead may be hot - handle with care. Removing the Blade and Fan Renew your metal blade after 50 hours mowing or 2 years whichever is the sooner regardless of condition. If the blade is cracked or damaged replace it with a new one. 1. Ensure the Operator Presence Control is released, when the engine has stopped and the blade has stopped rotating - disconnect the spark plug lead. 2. Fully close the fuel tap (K). 3. Turn your lawnmower on its side with the air cleaner uppermost (see pic above). 4. To remove the blade bolt (P1), hold the fan (P4) firmly and with the spanner provided loosen the blade bolt by turning it anti-clockwise. 5. Remove the blade bolt (P1), blade (P2), spacers (P3) and fan (P4). 6. Inspect for damage and clean as necessary.

ENGLISH - 3

Fitting the Blade and the Fan Before using the lawnmower, always visually inspect to see that blades and bolts are not worn or damaged. Never use more than 2 cutting height spacers. Spacers can only be fitted between the blade and the fan and never between blade and the bolt. 1. Ensure the fan is located correctly. 2. Place the spacers (P3) onto the fan ensuring the pegs (P5) have located into the holes (P6). 3. Place the blade (P2) onto the spacers (P3) ensuring the pegs (P7) have located into the holes (P8) on the blade and ensuring the blade is positioned as illustrated in Figure P. 4. Place the blade bolt (P1) through the centre hole (P9) of the blade. 5. Tighten down clockwise by hand. 6. Hold the fan firmly and tighten the blade bolt with the spanner provided.

Spark Plug

An oily or carboned spark plug makes starting difficult and decreases the efficiency of the engine. Periodically remove the spark plug and clean and adjust when necessary. Gap setting 0.028 - 0.031". Do not remove spark plug when engine is hot. Do not sand blast the spark plug to clean it.

Cleaning the Air Filter

Q1 - Air Duct Q2 - Air Cleaner Body Q3 - Filter Q4 - Latch Tabs Q5 - Air Cleaner Cover Never run the engine without a filter or with a dirty filter. This will greatly reduce engine efficiency and lead to engine damage. Your lawnmower is fitted with an Air Cleaner, the maintenance for which is as follows: Check the filter before each use. Clean every 25 hrs or more frequently when used in dusty areas. Replace filter every 200 hrs. 1. Press the latch tabs on the top of the air cleaner cover and remove the cover. 2. Check the filter is clean and in good condition. If the filter is dirty:Tap the air filter several times on a hard surface to remove dirt, or blow compressed air through the air filter from the clean side that faces the engine. Never try to brush off dirt. Brushing will force dirt into the fibers. 3. Wipe dirt from the air cleaner body and cover using a moist rag. Be careful to prevent dirt from entering the air duct that leads to the carburetor. 4. Replace the filter and air cleaner cover.
Caring for your Lawnmower
If you do not intend to use your lawnmower for long periods it is advisable to follow this procedure after use: 1. Stop the engine. 2. Fully close the fuel tap. (K) 3. Restart the engine. 4. As fuel runs out the engine will begin to stop, tilt the lawnmower slightly. 5. Once the engine has stopped, release the Operator Presence Control. 6. Disconnect the spark plug lead. 7. Remove all fuel from the fuel tank. Cleaning - USE GLOVES Keep your lawnmower clean - grass clippings left in any of the air intakes, around the engine or under the deck could become a potential fire hazard. Do not clean with chemicals, including petrol, or solvents - some can destroy critical plastic parts. 1. Remove grass from under the deck with a piece of wood or similar. 2. Using a soft brush - remove grass clippings from around the engine and from all air intakes. 3. Remove the fan, See 'Removing and Fitting the Blade and Fan', and clean with a soft brush. 4. Wipe over the surface of your lawnmower with a dry cloth. Transporting your Lawnmower Turn the fuel tap to the off position and transport with the engine in a horizontal position. Never transport the lawnmower when it is running. Storing Your Lawnmower Turn the fuel tap to the off position and store in a cool, dry, damp-proof and safe place with the engine in a horizontal position. Service your lawnmower after the last cut of the year as follows:At the end of the Mowing Season 1. Stop the engine. 2. Fully close the fuel tap. (K) 3. Restart the engine. 4. As fuel runs out the engine will begin to stop, tilt the lawnmower slightly. 5. Once the engine has stopped, release the Operator Presence Control. 6. Disconnect the spark plug lead. 7. Remove all fuel from the fuel tank. 8. Remove the spark plug lead and spark plug. Pour one teaspoon (5ml) of oil through the spark plug hole. Pull the starting handle 2 or 3 times. This will distribute oil on the internal surfaces of the engine. Inspect, clean and replace the spark plug. If a new spark plug is required contact your local approved Electrolux Outdoor Products Service Centre/Dealer. Do not re-connect the spark plug lead. 9. Clean the air filter. See 'Cleaning the Air Filter'. 10. Renew the blade if it is cracked, damaged or bent. Renew the blade bolt if necessary. See 'Removing and Fitting the Blade and Fan' for complete instructions. 11. Use only genuine Flymo parts and accessories specified for this product. 12. Clean your lawnmower thoroughly See 'Cleaning'. 13. Your local approved Electrolux Outdoor Products Service Centre/Dealer will carry out any service or repairs required. 14. Store your lawnmower in a cool, dry, damp-proof and safe place.

ENGLISH - 4

Fault Finding
Engine Will Not Start 1. Ensure that the Operator Presence Control is gripped firmly to the upper handle. 2. Check that there is sufficient fuel in the fuel tank and the fuel tap is open 3. Check that the choke control lever is in the correct position:- 'Run position (N) - for a hot engine, 'Choke position (L) - for a cold engine. 4. The engine may have flooded. Remove and dry the spark plug. 5. Petrol may be stale, replace. Once the petrol has been replaced, it may take a little time for fresh petrol to filter through. 6. Check that the blade bolt is tight. A loose blade bolt could cause difficult starting. 7. If the engine will still not start - disconnect the spark plug lead and consult you local approved Electrolux Outdoor Products Service Centre/Dealer. Poor Flotation or Lack of Power 1. Disconnect the spark plug lead. 2. Clean the underside of the hood, the air filter, the fan, around the engine and the air intakes. 3. Check that the engine choke control lever is in the 'Run' position. (N) 4. Petrol may be stale, replace. Once the petrol has been replaced, it may take a little time for fresh petrol to filter through. 5. If poor flotation or lack of power persists disconnect the spark plug lead and consult your local approved Electrolux Outdoor Products Service Centre/Dealer. Excessive Vibration 1. Disconnect the spark plug lead. 2. Check that the blade is correctly fitted. 'See 'Fitting and Removing the Blade and the Fan'. 3. If the blade is damaged or worn, renew the blade. 4. If vibration persists - do not use - disconnect the spark plug lead and consult your local approved Electrolux Outdoor Products Service Centre/Dealer.

Service Recommendations

Your product is uniquely identified by a silver and black product rating label. We strongly recommend that your product is serviced at least every twelve months, more often in a professional application.
Guarantee and Guarantee Policy
If any part is found to be defective due to faulty manufacture within the guarantee period, Electrolux Outdoor Products, through its Authorised Service Repairers will effect the repair or replacement to the customer free of charge providing: (a) The fault is reported directly to the Authorised Repairer. (b) Proof of purchase is provided. (c) The fault is not caused by misuse, neglect or faulty adjustment by the user. (d) The failure has not occurred through fair wear and tear. (e) The machine has not been serviced or repaired, taken apart or tampered with by any person not authorised by Electrolux Outdoor Products. (f) The machine has not been used for hire. (g) The machine is owned by the original purchaser. (h) The machine has not been used outside of the country for which it was specified. (i) The machine has not been used commercially. * This guarantee is additional to, and in no way diminishes the customers statutory rights. Failures due to the following are not covered, therefore it is important that you read the instructions contained in this Operator's Manual and understand how to operate and maintain your machine: Failures not covered by guarantee * Replacing worn or damaged blades * Failures as a result of not reporting an initial fault. * Failures as a result of sudden impact. * Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator's Manual. * Machines used for hire are not covered by this guarantee. * The following items listed are considered as wearing parts and their life is dependent on regular maintenance and are, therefore not normally subject to a valid warranty claim: Blades, belts, cables, recoil ropes, filters. * Caution! Electrolux Outdoor Products does not accept liability under the warranty for defects caused in whole or part, directly or indirectly by the fitting of replacement parts or additional parts that are not either manufactured or approved by Electrolux Outdoor Products, or by the machine having been modified in any way.

Environmental Information
Electrolux Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where practical, components manufactured in the most environmentally responsible manner, according to company procedures, and with the potential for recycling at the end of the products life. Packaging is recyclable and plastic components have been labelled (where practical) for categorised recycling. Awareness of the environment must be considered when disposing of end-of-life product. If necessary, contact your local authority for disposal information. DISPOSAL OF FUELS AND LUBRICATING OILS Wear protective clothing when handling any fuels and lubricants. Avoid contact with skin. Remove petrol and engine oil before transporting the product. Contact your local authority for information of your nearest Recycling/Disposal Station. Do NOT dispose of used fuels/oils with household waste Do NOT dispose of used fuels/oils to water. Waste fuels/oils are harmful, but can be recycled and should be disposed of through the recognised facilities. Do NOT incinerate

ENGLISH - 5

DECLARATION OF CONFORMITY KONFORMITTSERKLRUNG
I, the undersigned M. Bowden of Electrolux Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Durham. DL5 6UP. Certify that the Lawnmower:Category. Petrol Hover Make. Electrolux Outdoor Products Conforms to the specifications of Directive 2000/14/EEC
DCLARATION DE CONFORMIT CONFORMITEITSVERKLARING
I, the undersigned M. Bowden of Electrolux Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Durham. DL5 6UP Certify that a sample of the above product has been tested using ISO 5349 as a guide. The maximum weighted root mean square value of vibration recorded at operators hand position was:-
I, the undersigned M. Bowden of Electrolux Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Durham. DL5 6UP Certify that a sample of the above product has been tested using directive 81/1051/EEC as a guide. The maximum Aweighted sound pressure level recorded at operator position under free field semi anechoic chamber conditions was :-

BELGIQUE/BELGI ESK REPUBLIKA
Flymo Belgique/Belgi Tel: 0311, Fax: 0391 Electrolux, spol. s.r.o., oz Electrolux Outdoor Products, Na Keku 365, Praha 10 - Horn Mcholupy. Tel: 02/7847 0164, Info-linka: 0800/Internet: www.partner-flymo.cz E-mail: info@husqvarna.cz Electrolux Outdoor Products, Flymo/Partner A/S, Lundtoftegaardsvej 93A, DK 2800 Kgs.Lyngby Tel: 75 77, Fax: 33 08, www.flymo-partner.dk Flymo Deutschland Tel: 7640, Fax:764202 Electrolux Estonia Ltd (Electrolux Eesti AS) Tel: (372) 6650010 Flymo France SNC Tel 67 8141, Fax Electrolux Outdoor Products Finland Tel: 9 39611, Fax: 2644 McCulloch Italiana s.r.l. - Via Como 72, 23868 Valmadrera (LECCO) - ITALIA Tel: 800 017829, Fax: Flymo Ireland Tel: 01 4565222, Fax: Electrolux Lehel Kft Tel: Flymo/Partner, div. av Electrolux Motor a.s. Tel: Flymo Nederland Tel: 0172-468322, Fax: 0172-468219 Husqvarna-Ges.m.b.H. Nfg. KG, Industriezeile 36, 4010 LINZ, Tel: 0732 770101-0, Fax: 0732 770101-40, email: office@husqvarna.co.at Internet: www.husqvarna.at Electrolux Poland Sp. z.o.o. Husqvarna, 01-612 Warszawa Myslowicka 10/2 Tel:- (22) 8332949 Husqvarna-Ges.m.b.H. Nfg. KG, Industriezeile 36, 4010 LINZ, Tel: 0732 770101-0, Fax: 0732 770101-40, email: office@husqvarna.co.at Internet: www.husqvarna.at Electrolux Slovakia s.r.o., Borova Sihot 211, Lipt. Hradok Tel: 14 19, Fax: 14 18, www.flymo-partner.sk Flymo Schweiz/Suisse/Suizzera Tel / 25, Fax / 35 Electrolux Outdoor Products, Sverige Tel: 67 00, Fax: Electrolux Outdoor Products United Kingdom Tel: 01325 300303, Fax: 01325 310339

DANMARK

DEUTSCHLAND ESTONIA FRANCE FINLAND SUOMI ITALIA
IRELAND MAGYARORSZG NORGE NEDERLAND STERREICH

POLSKA

SLOVENIJA
SLOVENSKA SCHWEIZ/SUISSE/SUIZZERA SVERIGE UNITED KINGDOM
Electrolux Outdoor Products Aycliffe Industrial Park NEWTON AYCLIFFE Co.Durham DL5 6UP ENGLAND Telephone - (00) 300303 Fax - (00) 310339 UK Telephone - Fax - 01325 310339
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice. Electrolux Outdoor Products manufacture products for a number of well known brands under various registered patents, designs and trademarks in several countries. Electrolux Outdoor Products Ltd. Registered Office, Electrolux Works, Oakley Road, Luton LU4 9QQ Registered number 974979 England
The Electrolux Group. The worlds No.1 choice.
The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.

ELECTROLUX OUTDOOR PRODUCTS

PNC 9638507-59

Type/Prefix/nd 1

Model XL500

Market

Number of Pages 1 of 3

Factory: FLM - Aycliffe Publication Number: Publication Date: AP0410002 25/10/04
Product Group: OM 72 Petrol Hover Sub Group: 1072

Page No. 2of 3 OM

9638507-59 Petrol Hover

XL500 Newton Aycliffe

Page No. 3 of 3 OM

Xl500 Newton Aycliffe

Item 31 32
Part Number 512621000 510620620
Description Spanner Blade Bolt Blade 51cm Blade Spacer Impeller Screw Screw M10 Washer Label Key Woodruff Screw Washer Adaptor Plate Spring Clip Washer Wing Nut Tie Wrap Washer Nut Handle Upper Bail Arm Spacer Knob Screw M6 Cable Brake Cable Choke Knob Handle Lower Starlock Washer Label Warning Guide Slotted Hood 47cm

Part Number

Description