pHep is a rugged pH tester with replaceable
electrode and renewable reference junction. The instrument can be calibrated at two points by the user, simply acting on the offset and slope calibration trimmers.
pHep is in compliance with the CE direc-

HI 98107

Pocket-sized pH Meter
tives. SPECIFICATIONS Range 0.0 to 14.0 pH Resolution 0.1 pH Accuracy (@20C/68F) 0.1 pH Typical EMC Deviation 0.1 pH Calibration Manual, 2 point, through offset and slope trimmers Environment 0 to 50C (32 to 122F); RH max 95% Battery Type 4 x 1.5V alkaline Battery Life approx. 700 hours of use Dimensions 175 x 41 x 23 mm (6.9 x 1.6 x 0.9") Weight 95 g (3.4 oz.) ACCESSORIES HI 73106 HI 7004M HI 7007M HI 7010M HI 70300M HI 7061M HI 731326
Spare electrode pH 4.01 solution, 230 mL bottle pH 7.01 solution, 230 mL bottle pH 10.01 solution, 230 mL Storage solution, 230 mL bottle Cleaning solution, 230 mL bottle Calibration screwdriver (20 pcs)
pHep is a registered Trademark of Hanna Instruments

IST98107 R5

CONDITIONING
Remove the cap. To activate the electrode, immerse it in HI70300 storage solution for 2 hours.

CALIBRATION

Immerse the electrode in pH 7.01 (HI7007) buffer solution. Allow the reading to stabilize and with the supplied screwdriver, adjust the pH7 calibration trimmer to read 7.0 pH. Rinse the electrode with tap water and immerse it into the second buffer. Use pH 4.01 (HI7004) if the solution to be measured is acidic (pH < 7), or pH 10.0 (HI7010) for alkaline samples (pH > 7). Allow the reading to stabilize and with the screwdriver adjust the pH4/10 calibration trimmer to read 4.0 or 10.0 pH.
Pull out 2 mm (1/8'') of the cloth junction to renew the electrode reference (it is recommended to cut the cloth leaving always at least 2 mm 1/8'' over the reference compartment) and recalibrate the meter. The cloth junction can be pulled out approximately 20 times. After that, the electrode should be replaced.

ELECTRODE REPLACEMENT

For replacing the electrode, contact your Dealer or the nearest Hanna Service Center.

BATTERY REPLACEMENT

If calibration can not be performed or the display fades, batteries must be replaced. Slide off the battery compartment cover and replace all four 1.5V alkaline batteries, while paying attention to the correct polarity.

OPERATION

Remove the protective cap, turn the pHep on, by sliding the ON/OFF switch on the top of the meter. Immerse it in the solution to be tested without exceeding the maximum immersion level. Stir gently and wait for the reading to stabilize. After use, switch the meter off, rinse the electrode with tap water and store it with a few drops of storage (HI70300) or pH7 (HI7007) solution in the protective cap. Always replace the protective cap after use. NEVER USE DISTILLED OR DEIONIZED WATER FOR STORAGE PURPOSES. Large differences in pH readings (1 pH) could be due to lack of calibration or dry electrode. Batteries should only be replaced in a non-hazardous area and using the battery type specified in this instruction manual.

WARRANTY

This meter is guaranteed for one year against defects in workmanship and materials when used for their intended purpose and maintained according to instructions. This warranty is limited to repair or replacement free of charge. Damages due to accident, misuse, tampering or lack of prescribed maintenance are not covered. If service is required, contact the dealer from whom you purchased the instrument. If under warranty, report the model number, date of purchase, serial number and the nature of the failure. If the repair is not covered by the warranty, you will be notified of the charges incurred. If the instrument is to be returned to Hanna Instruments, first obtain a Returned Goods Authorization Number from the Customer Service department and then send it with shipment costs prepaid. When shipping any instrument, make sure it is properly packaged for complete protection.

MAINTENANCE

The sensor should be kept moist at all times. For this purpose, always keep wet the tissue inside the protective cap. In case of erroneous readings even after an accurate conditioning and calibration, the reference junction might be contaminated or clogged.

HI 98107

Pocket-sized pH Meter
pHep is a rugged pH tester with replaceable electrode and renewable reference junction. The instrument can be calibrated at two points by the user, simply acting on the offset and slope calibration trimmers. CONDITIONING: Remove the cap. To activate the electrode, immerse it in HI70300 storage solution for 2 hours. CALIBRATION: Perform one of the following two-point calibration procedure, according to the required application: Acid calibration for measurements below pH 7: Immerse the electrode in pH 7.01 (HI7007) buffer solution. Allow the reading to stabilize and with a small screwdriver turn the pH7 Calibration Trimmer until the display shows "7.0". Rinse the electrode with tap water and immerse it in pH 4.01 (HI7004) buffer solution. Allow the reading to stabilize and with a small screwdriver turn the pH4/pH10 Calibration Trimmer until the display shows "4.0". Alkaline calibration for measurements above pH 7: Immerse the electrode in pH 7.01 (HI7007) buffer solution. Allow the reading to stabilize and with a small screwdriver turn the pH7 Calibration Trimmer until the display shows "7.0". Rinse the electrode with tap water and immerse it in pH 10.01 (HI7010) buffer solution. Allow the reading to stabilize and with a small screwdriver turn the pH4/pH10 Calibration Trimmer until the display shows "10.0". OPERATION: Remove the protective cap. Turn the meter on with the ON/OFF switch located on the top of the meter. Immerse it in the solution to be tested without exceeding the maximum immersion level.
Stir gently and wait for the reading to stabilize. After use, rinse the electrode with tap water to minimize contamination. Store the electrode with a few drops of storage (HI70300) or pH7 (HI7007) solution in the protective cap. Always replace the protective cap after use. DO NOT USE DISTILLED OR DEIONIZED WATER FOR STORAGE PURPOSES. Large differences in pH readings (1 pH) could be due to lack of calibration or dry electrode. MAINTENANCE: The sensor should be kept moist at all times. For this purpose, always keep wet the tissue inside the protective cap. In case of erroneous readings even after an accurate conditioning and calibration, the reference junction might be contaminated or clogged. Pull out 2 mm (1/8'') of the cloth junction to renew the electrode reference (it is recommended to cut the cloth leaving always at least 2 mm -1/8'' over the reference compartment) and repeat the calibration procedure. The cloth junction can be pulled out approximately 20 times. After that, the electrode can be replaced (see the Electrode Replacement section). BATTERY REPLACEMENT: If calibration can not be performed or the display fades, batteries level is low and batteries must be replaced. Slide off the battery compartment cover and replace all four 1.5V batteries while paying attention to their polarity.

300 HI 70

Batteries should only be replaced in a nonhazardous area using the battery type specified in this instruction manual.

Manufacturers since 1978

SPECIFICATIONS: RANGE 0.0 to 14.0 pH RESOLUTION 0.1 pH ACCURACY (@20C/68F) 0.1 pH TYPICAL EMC DEVIATION 0.1 pH ENVIRONMENT 0 to 50 C (32 to 122 F); 95% RH Manual, at two points through CALIBRATION offset and slope trimmers BATTERY TYPE 4 x 1.5V alkaline (included) BATTERY LIFE approx. 1700 hours of continuous use DIMENSIONS 175 x 41 x 23 mm (7.9 x 1.8 x 1") WEIGHT 78 g (2.7 oz.) ACCESSORIES: HI 73106 Spare electrode HI 77400P pH 4.01 & 7.01 calibration kit (5 x 20 mL, each) HI 77700P pH 7.01 calibration kit (10 x 20 mL) HI 770710P pH 7.01 & 10.01 calibration kit (5 x 20 mL, each) HI 7004M pH 4.01 buffer solution (230 mL bottle) HI 7007M pH 7.01 buffer solution (230 mL bottle) HI 7010M pH 10.01 buffer solution (230 mL bottle) HI 70300M Storage solution (230mL) HI 7061M Electrode cleaning solution (230mL bottle) HI 731326 Calibration screwdriver (20 pcs)
Visit our Internet Home Page: http://www.hannainst.com
ELECTRODE REPLACEMENT: The electrode can be easily replaced in the following way: Slide off the battery cover. Remove the screw on the back of the pHep located below the battery compartment and slide off the whole internal part of the tester.
Internal circuit and electrode:
Reinsert the battery compartment cover. To remove the electrode proceed as follows: Remove the fastening screw on the front (1) to loose the electrode. The internal circuit is connected to the electrode through two wires (one for the glass sensor and one for the reference). Remove the two small screws (2 & 3) which fasten the two connecting wires to their sockets. Remove the electrode and replace it with a new HI73106. Connect the new electrode as follows: first fasten the screw on the front (1) to attach the electrode to the circuit. Insert the two small wires into their sockets and fasten the HI73106 two screws (2 & 3). The new electrode is supplied with four new Orings (4). Make sure they are placed properly (as shown on the above drawing) before reinserting the circuit into the plastic casing. Reinsert the internal circuit with the new electrode into the plastic casing. Fasten the screw on the back below the battery compartment.
Perform a new calibration before using the pHep again.
ONE YEAR WARRANTY & SERVICEABLE: Covered by one year warranty against defects in workmanship and materials, this tester is now completely serviceable. Contact your dealer for further information.

The pHep is in compliance with the CE directives EN 50082-1, EN 50081-1 and EN 61010-1.

IS98107-R3

pHep is a registered Trademark of "Hanna Instruments"