Manual

doro bm35

babymonitor

English
Scroll UP Button Menu Button Microphone External microphone socket (optional) 7 On/Off switch
Microphone sensitivity (rear) Scroll DOWN Button
Important! Although the baby monitor offers a practical solution in looking after a child it cannot replace a parent or guardian. Make sure the equipment is always out of reach, never place the unit in the childs bed or playpen. To avoid acoustic feedback by not placing the handset and baby monitor close to one another. Radio signals can be blocked if the equipment is used in areas with high sources of interference from other electronic equipment.
Turning on/off Use the switch 0/1 on the side of the monitor to turn the unit on or off. Connection/Monitoring 1. Connect the mains adapter to an electrical wall socket. 2. Make sure that the monitor and handset are set to the same channel and transfer code. See below. 3. Position the monitor close to the baby (but out of reach). 4. Adjust the microphone sensitivity using the VOX control on the rear of the monitor (A=least sensitive.H=most sensitive). Please refer to page 4. 5. When the sound level in the room exceeds the selected VOX setting, the handset will be triggered allowing you to monitor the room. 6. Try the installation before every use by talking quite low into the unit that is placed close to the baby, at the same time as someone is listening to the other unit.

Please note!

If the monitor and handset/s are unable to communicate it may be because you are using different channels or transfer codes, the battery is running low or the units are too far apart. There is NO loudspeaker in the monitor, this ensures your child will not be disturbed by radio chatter that is often heard on the handset/s. Important! Please note when programming all references to press = to press and then immediately release the button. Channel selection All UHF/CB radio equipment share the available designated channels. If the chosen channel is in use select an alternate channel, the selected channel number will be displayed in standby mode. Please refer to the frequency/channel allocation table on page 6. 1. Press MENU. CH will be displayed. 2. Scroll to the desired channel using v/V. 3. Within a few seconds the display will return to standby mode. Transfer code selection There are 38 transfer codes available which can be used to filter out unwanted signals. To enable monitoring, the same transfer code must be used on the monitor and all handsets. However, the communication between monitor and handset/s may still be overheard irrespective of which code is used. 1. Press MENU repeatedly until Ct is displayed. 2. Scroll to the desired transfer code using v/V. 3. Within a few seconds the display will return to standby mode.

www.doro.com

Safety signal The monitor can transmit a tone every 30 seconds to confirm that the right channel/ transfer code has been set and that the operating range has not been exceeded. Beep will be displayed while this function is active. 1. Press MENU repeatedly until Beep is displayed. 2. Scroll to the required setting using v/V (OF =off, On =on). 3. Within a few seconds the display will return to standby mode. Automatic monitoring This automatically switches the monitor function on for five seconds every five minutes. Auto Mon will be displayed while this function is active. 1. Press MENU repeatedly until Auto Mon is displayed. 2. Scroll to the required setting using v/V (OF =off, On =on). 3. Within a few seconds the display will return to standby mode. Alert signal You can activate a tone that is heard when the monitor transmits. will be displayed while this function is active. 1. Press MENU repeatedly until CA and is displayed. v/V (OF =off, On =on). 2. Scroll to the required setting using 3. Within a few seconds the display will return to standby mode. Voice control (VOX) By selecting the right level, the monitor can automatically determine whether or not the sound level in the room is normal (=quiet). Test different settings until the sensitivity selected is acceptable (A=least sensitive.H=most sensitive). Please note that however accurate your setting there is always a small risk that increased noise from the surroundings may activate the transmitter. Range The monitor is intended for both indoor and outdoor use, it is NOT resistant to rain, water, rough or other careless treatment. In ideal conditions ie: line of sight with no obstructions between monitor and handset/s, the range can be up to 3 km.

UK If you cannot resolve the fault using the faultfinder section, technical support is available on the Premium Rate Number: 0114. Calls cost 50 pence per minute (prices correct at the time of going to press), and is operational between 9AM - 5PM Monday-Friday excluding Bank Holidays. Alternatively, E-mail on: tech@doro-uk.com You can contact us in writing: Consumer Support Group, Doro UK Ltd., 22 Walkers Road, North Moons Moat, Redditch, Worcestershire, B98 9HE, (regarding any Spares or Technical query), or Telephoning (Spares only): Web site: www.doro-uk.com Guarantee This product is guaranteed for a period of 12 months from the date of purchase. Proof of purchase is required for any service or support required during the guarantee period. This guarantee shall not apply to a fault caused by an accident or a similar incident or damage, liquid ingress, negligence, abnormal usage, not reasonably maintained or any other circumstances on the purchasers part. Furthermore, this guarantee shall not apply to a fault caused by a thunderstorm or any other voltage fluctuations. This guarantee does not in any way affect your statutory rights. (As a matter of precaution, we recommend disconnecting the telephone during a thunderstorm.)
Australia and New Zeeland
AUSTRALIA DORO Australia Pty Ltd PO Box 6760 Baulkham Hills BC NSW 2153 Australia Consumer Support Ph: Ph: 023 Fax: (02) 8853-8489 Email: support@doro.com.au Web site: www.doro.com.au
The product complies with AS/NZS 4365.
NEW ZEALAND Atlas Gentech (NZ) Limited Private Bag 14927 Panmure Auckland New Zealand Consumer Support Ph: 0900-500-25 (Toll Call) Fax: (09) 574-2722 Email: support@atlasgentech.co.nz

N13 Z109

www.doro.com

* These channels are the repeater access channels ( mode). ** Designated emergency channels. ! Speech telephony is not permitted on these channels.

English Version 1.0

en_bm35+1_facts

05-10-18

Sida 1

say it with style

doro bm35+1

baby monitor

Multiple channels Secure range up to 3 km Alert tone Rechargeable batteries included Voice activation adjustment Walkie Talkie functionality

Sida 2

Baby unit Channels Subcodes Automatic monitor (transmission) Alert tone VOX settings Range (kilometres) Channel memory LCD display External mic input Backlit display Parents unit Number of parent units Walkie talkie functionality (PMR) Channels Subcodes Automatic squelch Calling tones Monitor mode VOX settings (including off) Roger beep Range (kilometres) Auto channel scan Dual channel monitor Stopwatch Channel memory Channel lock Volume control levels Key tone LCD display Backlit display Display light when receiving Auto power save Battery low indicator Flashlight Headset outlet Belt clip Re-chargeable battery pack 3 up to 3 8 NiMH 8 up to 3

www.doro.com