FITTING INSTRUCTION
Clamp mark in acc. with ISO PN 1 L 2 + 4 R 5 58R 7 58L Cables joining Left directional lights Rear fog lights Ground Right directional lights Right side parking lights Stoplights Left side parking lights
The instruction of the assembly
1. Before beginning installation one ought to read instruction of the car (see page 158), in this point manufacturer describe places where towbar should be installed. 2. According to fig. 2 drill holes: - Left side from hole no. 3 measure 110mm to rear side of the car and drill hole 11mm (straight through), from this hole measure 152mm and drill another hole 11mm (straight through too). - Right side from hole no. 1 measure 110mm to rear side of car and drill 11mm (straight through).

LEFT RIGHT

Rear side of the car Existing holes 25mm
This towbar is designed to assembly in following cars: FIAT SEICENTO, 3 doors, produced since 1998, catalogue no. S08 and is prepared to tow trailers max total weight 400 kg and max vertical load 28 kg.

From manufacturer

Thank you for buying our product. Their reliability has been confirmed in many tests. Reliability of towbar depends also on correct assembly and right operation. For this reasons we kindly ask to read carefully this instruction and apply to hints. The towbar should be install in points described by a car producer.
3. Maked holes drill again using bit 17,5mm only in upper side. 4. To this holes slip distance slevees 17mm L=55 (pos. 6). 5. To existing hole 25 (no. 1, see fig. 2) slip threaded distance sleeve - pos. 7 (from below) and next through its holes drill holes 11mm to inside boot. 6. Put fish-plates (pos. 4 and 5) as shown in drawing and fix using bolts M10x90mm (pos. 10) and bolt M10x30mm (pos. 11). 7. From below the car, put the main bar of towbar (pos. 1) and fix as shown in the figure 1. 8. Through holes in fish-plates (pos. 4 and 5) drill holes 9mm and fix using bolts M8x25mm (pos. 12) as shown in figure 1. 9. Fix tow-ball (pos. 2) and socket plate (pos. 3) using bolts from the towbar accessories, see fig. 1. 10. Tighten all bolts according to the torque shown in the table. 11. Connect electric wires of 7-bolts socket according to the instruction of the car. (Recommend to make at authorized service station) 12. Complete the paint coating damaged during installation.
Torque settings for nuts and bolts (8,8): M 8 - 25 Nm M 10 - 55 Nm M 12 - 85 Nm M 14 - 135 Nm

Towbar accessories:

PPUH AUTO-HAK S.J.
Produkcja Zaczepw Kulowych Henryk & Zbigniew Nejman 76-200 SUPSK ul. Soneczna 16K tel/fax (059) 8-414-414; 8-414-413 E-mail: office@autohak.com.pl www. autohak.com.pl
Towing hitch (without electrical set)

Class: A50-X

Cat. no. S08
Designed for: Manufacturer: FIAT Model: SEICENTO Type: 3 doors produced since 1998
Technical data: D-value: 2,94 kN maximum trailer weight: 400 kg maximum vertical cup load: 28 kg
Approval number acc. to regulations EKG/ONZ 55.01: E20-55R-NOTE After install the towbar you should get adequate note in registration book (at authorised service station). The car should be equipped with: Indicators Tow mirrors After 1000km of exploitation check all bolts and nuts. The ball of towbar must be always kept clear and conserve with a grease.

Foreword

This towbar is designed according to rules of safety traffic regulations. The towing hitch is a safety component and can be install only by qualified personnel. Any alteration or conversion of the towing hitch is prohibited and would lead to cancellation of design certification. Remove insulating compound and underseal from vehicle (if present) in the area of the matting surfaces of the towing hitch. The vehicle manufacturers specifications regarding trailer load and max. vertical cup load are decisive for driving whereat values for the towing hitch cannot be exceeded. D-value formula: Max trailer weight [kg] x Max vehicle weight [kg] Max vehicle weight [kg] X 9,81 = 1000