Continued Q

Close the battery cover.
If you want to use the camera powered by AC, the AC power adapter, AC-5VX, and DC coupler, CP-40N (both sold separately), are necessary. Refer to the manual provided with the AC-5VX and CP-40N for instructions.

Loading the Memory Card

Although you can store pictures in the cameras internal memory, you can store many more images on the Memory Card (sold separately). You can use the xDPicture Card and the SD Memory Card with the FinePix F480 / FinePix F485. In this Owners Manual, these cards are expressed as Memory Card. SD Memory Cards/SDHC Memory Cards They are operation-checked at FUJIFILM Corporation. Maker: SanDisk MEMO
Compatible Memory Cards will be updated in our website: http://www.fujifilm.com/products/digital_cameras/index.html Depending on the SD Memory Card, recording of movies may be interrupted. Use of above mentioned SD Memory Cards are recommended. The camera is not compatible with multimedia cards.

Insert a Memory Card.

(xD-Picture Card)

(SD Memory Card)

Be sure to unlock the protection of the SD Memory Card before inserting it. If it is locked, recording/deleting images, as well as formatting are not available. To unlock the protection, slide the switch back, and the SD Memory Card will work normally.

Protection switch

How to replace the Memory Card
A new SD Memory Card or a card previously used on a PC or any device other than the camera should be formatted (p.84) on the camera before use. Do not use a miniSD adaptor or a microSD adaptor which have exposed contact areas on the back. Use of these adaptors may cause a malfunction or damage due to the improper contacts.
Push the Memory Card into the slot and then slowly remove your finger. The lock is released and the Memory Card is pushed out.
Loading the Memory Card CAUTION
When storing Memory Cards, make sure that they are kept out of the reach of children. A Memory Card could be swallowed and cause suffocation. If a child swallows a Memory Card, seek medical attention or call emergency number right away. If the Memory Card is oriented incorrectly, it will not go all the way into the slot. Do not apply force when inserting a Memory Card. Note that the Memory Card may spring out if you release your finger quickly from the card immediately after the lock is released. Operation of this camera is only guaranteed when it is used with FUJIFILM xD-Picture Card and operationchecked SD Memory Card (p.16). See p.106 for information on the xD-Picture Card, SD Memory Card and the internal memory.

Z About internal memory

AUTO N 12 4
FinePix F480 / FinePix F485 has internal memory that can store images without Memory Card. Y appears on the LCD monitor when internal memory is active.

Taking Pictures (AUTO Mode) Z Indicator lamp display The indicator lamp lights or blinks when pressing the shutter button, etc. The indicator lamp shows the camera status.
Display Lit green Blinking green Lit orange Blinking orange Blinking red Status Locking the focus Camera shake warning, AF warning, or AE warning (ready to shoot) Recording to Memory Card or internal memory (not ready) Charging flash (flash will not fire) Warnings for Memory Card and internal memory Card not formatted, incorrect format, memory full, Memory Card or internal memory error Lens operation error

Indicator lamp

Detailed warning messages appear on the LCD monitor (p.107-110).
Taking pictures with the focus and exposure locked

Using AF/AE lock

Move the camera slightly so that one of the subjects is in the AF frame.
In the above composition, the subjects (two people in this case) are not in the AF frame. Pressing the shutter button halfway at this point will result in the subjects being out of focus.
Press the shutter button down halfway to focus on the subject.

AF/AE lock is useful:

Use AF/AE lock to guarantee best result when shooting a subject that is not suited to autofocusing (p.30).

Halfway pressed

Continue to hold the shutter button down halfway. Move the camera back to the original image and press the shutter button fully.
Subjects not suitable for autofocus
FinePix F480 / FinePix F485 uses a high-precision autofocusing mechanism. However, it may have difficulty focusing on the following:

Fully pressed MEMO

AF/AE lock can be applied repeatedly before the shutter is released. Use AF/AE lock in all Photography modes to guarantee excellent results. On FinePix F480 / FinePix F485, pressing the shutter button down halfway locks the focus and exposure settings (AF and AE lock).
Very shiny subjects such as a mirror or car body

Fast moving subjects

Subjects photographed through glass Subjects that do not reflect well, such as hair or fur Subjects with no substance, such as smoke or flames Dark subjects Subjects with little or no contrast between the subject and the background (such as subjects dressed in the same color as the background) Shots where another high-contrast object (not the subject) is close to the AF frame and is either closer or further away than your subject (such as a shot of someone against a background with strongly contrasting elements) For such subjects use AF/AE lock (p.29).
Adjusting the shot composition
Select the LCD monitor display.
Press DISP/BACK to change the LCD monitor display.

Best framing

Position the main subject at the intersection of two lines in this frame or align one of the horizontal lines with the horizon. Use this frame as a guide to the subjects size and the balance of the shot while composing a shot. MEMO

[DPOF SPECIFIED. ERASE OK ?] [DPOF SPECIFIED. ERASE ALL OK ?] (p.38) When erasing the image, the DPOF setting for that image is deleted at the same time. [ RESET DPOF OK ?] (p.65) When inserting a Memory Card that contains images specified for printing by another camera, those print specifications are all reset and replaced by the new print specifications. [DPOF FILE ERROR] (p.109) Up to 999 images can be specified on the same Memory Card.
Protecting the images ([ PROTECT])
Use this mode to prevent frames (files) from being accidentally erased. Your camera calls images frames.

[SET ALL]

SET ALL OK? IT MAY TAKE A WHILE

[FRAME SET] / [RESET]

To protect or unprotect only the selected frame (file):

YES CANCEL

PROTECT OK?

UNPROTECT OK?

Press MENU/OK to protect all the frames (files).
YES CANCEL YES CANCEL RESET ALL OK? IT MAY TAKE A WHILE

Unprotected

Protected (F appears)
A Press p or q to select the protecting/ unprotecting frame (file).
B Press MENU/OK to protect/unprotect the currently displayed frame (file). Unprotected: protecting frame (file) Protected: reset frame (file) To protect another frame (file), repeat steps A and B. When protecting frames (files) is completed, press DISP/ BACK.
Press MENU/OK to unprotect all the frames (files).
[PLAYBACK MENU] MEMO To stop the procedure midway
Copying the images ([ COPY])
It is possible to transfer saved images between the internal memory and a Memory Card. Your camera calls images frames.

Z Selecting COPY

COPY INTERNAL MEMORY CARD CARD
If the images are very large, protecting or unprotecting all the frames (files) may take some time. If you want to take a picture or record a movie during the procedure, press DISP/BACK.

INTERNAL MEMORY

The Format function erases all the frames (files), including protected frames (files) (p.84).
A Press n or o to select [Y INTERNAL MEMORY Q \ CARD] or [\ CARD Q Y INTERNAL MEMORY].

B Press q.

Copying one frame at a time ([FRAME])
COPY INTERNAL MEMORY CARD CARD FRAME ALL MEMORY INTERNAL FRAMES

COPY OK? 100 - 0001

YES YES CANCEL
A Press n or o to select [FRAME].

Install DirectX as directed by the on-screen instructions and then restart your PC. If the latest version of DirectX is already installed on your PC, this installation is not performed.
If the latest version of DirectX or Windows Media Player has not been installed, each software will be installed, and then the PC will restart. Do not remove the CD-ROM during this procedure.
* The way file names are displayed differs as described below
After restarting the PC, a message appears stating [Installation of the FinePixViewer has been completed]. Remove the CD-ROM from your PC.
depending on your PC settings. -File extensions (3-letter suffixes indicating the file type) may be shown or hidden. (e.g. Setup.exe or Setup) -Text may be shown normally or all in uppercase (e.g. Setup or SETUP).
Installation on a Mac OS X
Z Hardware and software requirements To run this software, you must have the hardware and software described below. Check your system before you begin the installation.
Compatible Mac*1 Operating System RAM Hard disk space Display Internet connection*3 Power Macintosh G3*2, PowerBook G3*2, Power Macintosh G4, iMac, iBook, Power Macintosh G4 Cube, PowerBook G4, Power Macintosh G5, MacBook, MacBook Pro or Mac Mini Mac OS X (compatible with version 10.3.9 to 10.4.9) 256 MB or better recommended Amount required for installation: 200 MB minimum Amount required for operation: 400 MB minimum pixels or better, at least 32,000 colors To use the FinePix Internet Service or mail attachment function: An Internet connection or e-mail transmission software is needed Connection speed: 56 kbps or better recommended
*1 PowerPC, Intel processor loaded *2 Models with a USB port as a standard feature *3 Required to use the FinePix Internet Service. The software can still be installed even if you do not have an Internet connection. CAUTION
Connect the camera directly to the Macintosh using the USB cable. The software may not operate correctly if you use an extension cable or connect the camera via a USB hub. Push the USB connector fully into the socket to ensure that it is securely connected. The software may not operate correctly if the connection is faulty. Additional USB interface board is not guaranteed.
Turn your Macintosh on and start up Mac OS X. Do not launch any other applications. When the bundled CD-ROM is loaded into the CD-ROM drive, the [FinePix] icon appears. Double-click the [FinePix] icon to open the [FinePix] volume window. Double-click on [Installer for MacOSX]. The Installer setup dialog appears. Click the [Installing FinePixViewer] button.

FinePix F480 / FinePix F485 is compatible with PTP (Picture Transfer Protocol)/MTP (Media Transfer Protocol). A PTP/MTP-compatible camera is a camera that can recognize the PC and printer automatically when connected. Do not disconnect the USB cable (included) when the camera is communicating with a PC. If the USB cable (included) is disconnected during communication, the files on the Memory Card or internal memory may be damaged. In Mac OS X, you must set automatic setup the first time you connect the camera to your PC. When the camera and PC are exchanging data, the indicator lamp blinks alternately green and orange. Auto power off is disabled during USB connection. Before replacing the Memory Card, always disconnect the camera from the PC. The camera and PC may be exchanging data even when Copying disappears from your PC screen. Before disconnecting the USB cable (included), always check that the indicator lamp is off. Always use FinePixViewer to transfer images with voice memos to a PC. The cost of an Internet provider for connecting to the internet is the users responsibility. When using FinePixViewer to save images on a data server (network), FinePixViewer may not run as it would in a standalone PC environment.
Always use the FUJIFILM AC Power Adapter AC-5VX (sold separately) and DC coupler CP-40N (Sold separately). If the camera suddenly loses power during data exchange, the Memory Card or internal memory could be damaged. Make sure that the USB cable (included) is connected correctly and securely. Connect the camera directly to the PC using the USB cable (included). The software may not operate correctly when you use an extension cable, or if you connect the camera via a USB hub. When your PC has more than one USB port, the camera can be connected to either port. When Windows 98 SE is used, the supplied software must be installed first before connecting the camera to a PC using the USB cable. The PC will not recognize the camera if it is connected before installation. A memory Card, the internal memory, data in a Memory Card or data in the internal memory could be damaged if any of the following are performed; - the USB cable is disconnected - power switch or buttons are pressed, or the lens cover is interfered with
The following steps differ depending on the PCs operating system (Windows 2000/XP/ Vista case)
When your PC recognizes the camera automatically, FinePixViewer S automatically starts up and the Load photos window appears. Follow the instructions provided on screen to save the images. To proceed without saving the images, click the [Menu] button. CAUTION

AC Power Adapter AC-5VX Use the AC-5VX when taking pictures or play back images for long periods or when FinePix F480 / FinePix F485 is connected to a PC. * The shape of the AC power adapter, the plug, and power outlet depend on the country.
DC Coupler CP-40N Use the CP-40N with AC-5VX when taking pictures or play back images for long periods or when FinePix F480 / FinePix F485 is connected to a PC.
PC Card Adapter DPC-AD The PC Card Adapter allows the xD-Picture Card and SmartMedia to be used as a PC Card Standard ATA-compliant (PCMCIA 2.1) PC card (Type u). - Compatible with xD-Picture Card of 16 MB to 512 MB, and SmartMedia of 3.3 V, 2 MB to 128 MB. This is not compatible with the SD Memory Card. CompactFlash Card Adapter DPC-CF Loading an xD-Picture Card into this adapter allows you to use the card as a CompactFlash card (Type s). - This is not compatible with the SD Memory Card.

e Card

Using Your Camera Correctly
Read this information and the Safety Notes (Notes and Cautions), to make sure you use your camera correctly. Z Places to Avoid Do not store or use the camera in the following types of locations: In the rain or in very humid, dirty, or dusty places In direct sunlight or in places subject to extreme temperature rises, such as in a closed car in summer Extremely cold places Places with strong vibration Places with smoke or steam Places subject to strong electric magnetic fields (such as near broadcasting tower, power lines, radar, motors, transformers, magnets, etc.) In contact with chemicals such as pesticides Next to rubber or vinyl products Z Damaged by Water or Sand FinePix F480 / FinePix F485 can be damaged on the inside and outside by water and sand. When you are at the beach or close to water, make sure that the camera is not damaged by water or sand. Take care not to place the camera on a wet surface. Z Damaged by Condensation If the camera is carried from a cold location into a warm place, water droplets (condensation) may form on the inside of the camera or on the lens. When this occurs, turn the camera off and wait an hour before using the camera. Condensation may also form on the Memory Card. In this event, remove the Memory Card and wait a short time. Z When the Camera is Not Used or is stored Periods of Time If you do not intend to use the camera for a long period of time, remove the battery and the Memory Card. Z Cleaning Your Camera Use a blower brush to remove any dust on the lens or LCD monitor, and then gently wipe the camera with a soft, dry cloth. If any soil remains, apply a small amount of lens cleaning liquid to a piece of FUJIFILM lens cleaning paper and wipe gently. Do not scratch hard objects against the lens or LCD monitor. Clean the body of the camera with a soft, dry cloth. Do not use volatile substances or cleaning products these items can cause damage. Z Using the Camera When Traveling When traveling overseas, do not place your camera in the check-in baggage. Baggage can be subjected to violent shocks, and the camera may be damaged inside or outside.

Notes on the xD-Picture Card, the SD Memory Card and the Internal Memory
Z Handling Memory Card When inserting the Memory Card into the camera, hold the Memory Card straight as you push it in. Never remove the Memory Card or turn the camera off during data recording or erasing (Memory Card formatting) as this could be damaged to the Memory Card. The use of xD-Picture Cards is recommended with FinePix F480 / FinePix F485. The recording quality cannot be guaranteed when xDPicture Cards other than those manufactured by FUJIFILM are used. The Memory Card may feel warm when it is removed from the camera after taking pictures. This is normal. Do not put labels on the Memory Card. Peeling labels can cause the camera not to work properly. MEMO Type M and H of xD-Picture Card
Type M There are two types of Memory Card: standard type and Type M (containing M in the model number, such as DPC-M2GB). FinePix F480 / FinePix F485 is compatible with Type M. Type H Type H and M share the same compatibility. Usable USB drive Type H cannot be used with xD-Picture Card USB drive DPC-UD1, while Type M can.
Z Internal Memory Images held in the cameras internal memory may be corrupted or erased due to problems such as camera faults. Save your important data to another media (i.e., DVD-R, CD-R, CD-RW, hard disk, etc.). Data stored in the cameras internal memory cannot be guaranteed in the event that the camera is submitted for repairs. When the camera is repaired, any data stored in the cameras internal memory is subject to checking by the repairer. Z Using Memory Card or Internal Memory with a PC When taking pictures using a Memory Card or internal memory that has been used on a PC, reformat the Memory Card using your camera. When formatting, a directory (folder) is created. Image data is then recorded in this directory. Do not change or delete the directory (folder) or file names on the Memory Card or internal memory because this will make it impossible to use the Memory Card or internal memory in your camera. Always use the camera to erase image data. To edit image data, copy or transfer the image data to the PC and edit the copied or transferred data.

Warning Displays

The table below lists the warnings that are displayed on the LCD monitor.
Warning Displayed (Lit red) V (Blinking red) Explanation The batteries are low or completely out of charge. There is a strong likelihood of camera shake because the shutter speed is slow. The AF (autofocus) cannot work effectively. Remedy Load new or fully charged batteries. Use flash photography. A tripod may be recommended, depending on the scene and mode. If the image is too dark, take the picture at a distance of around 2 m (6.6 ft.) from the subject. Use AF lock to take the picture (p.29). Select Macro mode when taking close-up shots. The picture can be taken, but the correct brightness (exposure) will not be obtained. Turn the camera on again, taking care not to touch the lens. Turn the camera off and on again. If the message still appears, contact your FUJIFILM dealer. Insert a Memory Card. Format the Memory Card or internal memory on the camera (p.84). Format the Memory Card on the camera. Wipe the contact area on the Memory Card with a soft, dry cloth. It may be necessary to format the Memory Card (p.84). If the message still appears, replace the Memory Card. Contact your FUJIFILM dealer.

[FOCUS ERROR] [ZOOM ERROR] [NO CARD]
The camera cannot shoot the picture at the correct brightness due to too bright or dark shooting condition. Camera malfunction or fault.
Memory Card is not inserted when transferring images. The Memory Card or internal memory is not formatted. The Memory Card was formatted on a PC. The Memory Card contact area is soiled.

[CARD NOT INITIALIZED]

Camera fault.
Warning Displayed Explanation The Memory Card contact area is soiled. The Memory Card format is incorrect. [CARD ERROR] Remedy Wipe the contact area on the Memory Card with a soft, dry cloth. It may be necessary to format the Memory Card (p.84). If the message still appears, replace the Memory Card. Contact your FUJIFILM dealer.
Camera fault. The Memory Card is damaged. Inserted Memory Card is not compatible with your Insert a compatible Memory Card that is operationcamera. checked at FUJIFILM Corporation (p.16). The internal memory or Memory Card is full. Erase some images in internal memory or Memory Card (p.36), or use a Memory Card that has ample free space.
[\ MEMORY FULL] [Y MEMORY FULL]

[WRITE ERROR]

The data could not be recorded due to a Memory Re-insert the Memory Card or turn the camera off Card error or a connection error between the and then on again. If the message still appears, Memory Card and camera. contact your FUJIFILM dealer. The image cannot be recorded as it is too large to Use a new Memory Card. fit in the available space on the Memory Card. The Memory Card or internal memory is not Format the Memory Card or internal memory on formatted. the camera (p.84). The SD Memory Card switch is slide to the Lock side. Unlock the protection by sliding it back (p.17). Erase some images from the internal memory (p.36), or use a Memory Card that has ample free space. Use a Memory Card that was formatted on the camera. A Insert a formatted Memory Card into the camera. B Set [RENEW] as the [FRAME NO.] setting in the [ SET-UP] menu (p.81). C Start taking pictures (The frame number starts from 100-0001). D Set [CONT.] as the [FRAME NO.] setting in the [ SET-UP] menu.

[PROTECTED CARD]

[INTERNAL MEMORY IS The data could not be recorded or copied since the internal memory is full. FULL] [INSERT A NEW CARD] [BUSY] The timing for recording was incorrect because the Memory Card was formatted on a PC. The frame number has reached 999-9999.

Flash mode LCD monitor Movie
Photography functions Playback functions Other functions
Input/Output Terminal A/V OUT (Audio/Visual output) Digital input/output Power Supply and Others Power supply Rechargeable Battery NP-40N, AC power adapter AC-5VX (sold separately), DC coupler CP-40N (sold separately) NTSC/PAL-type (with monaural sound) USB 2.0 High-Speed, PTP (Picture Transfer Protocol)/MTP (Media Transfer Protocol)
Power Supply and Others Guide to the number of available frames for battery operation NP-40N Battery Type Number of frames Approx. 150 frames
According to the CIPA (Camera & Imaging Products Association) standard procedure for measuring digital still camera battery consumption (extract): When using a battery, use the battery supplied with the camera. The storage media should be xDPicture Card. Pictures should be taken at a temperature of +23C (+73F), with the LCD monitor turned on, the optical zoom moved from full wide-angle to full telephoto (or vice-versa) and back again to its original position every 30 seconds, the flash used at full power every second shot and the camera turned off and then on again once every 10 shots. Note: Because the number of available shots varies depending on the level of charge in the battery, the figures shown here for the number of available shots using the battery is not guaranteed. The number of available shots will also decline at low temperatures. Camera dimensions (W/H/ D) Camera mass (weight) Weight for photography Operating Conditions 95.6 mm 55.4 mm 23.0 mm/3.7 in. 2.1 in. 0.9 in. (not including accessories and attachments) Approx. 140 g/4.9 oz. (not including accessories, battery and Memory Card) Approx. 159 g/5.6 oz. (including battery and Memory Card) Temperature: 0C to +40C (+32F to +104F) 80% humidity or less (no condensation)
Battery NP-40N Nominal voltage Nominal capacity DC 3.6V 760 mAh
Notes on Using the Battery Charger
Operating temperature 0C to +40C (+32F to +104F) Dimensions Mass (Weight) 35.3 mm 40.0 mm 5.85 mm(1.4 in. 1.6 in. 0.2 in.)(W H D) Approx. 18 g (0.6 oz.)
Battery Charger BC-40N Rated input Input capacity Rated output Applicable batteries Charging time Dimensions Mass (Weight) Operating temperatures 110-240 V AC, 50/60 Hz 7 VA 4.2 V DC, 550 mA Rechargeable Battery NP-40N Approx. 120 minutes 88.0 mm 54.0 mm 20.0 mm (3.5 in. 2.1 in. 0.7 in.) (L W D) Approx. 58 g (2.0 oz.) (excluding batteries) 0C to + 40C(+ 32F to + 104F)

Use with the following power supply cord set: Cord: UL Listed, Type SPT-2, No.18 AWG, rated 300V, 10A, minimum 4 ft (1.2m), maximum 10 ft (3m) long. One end terminates in a molded-on, parallel-blade, (nonpolarized) attachment plug with a 7A, 125V (NEMA 115P) configuration. The battery and battery charger themselves will become warm due to the power stored inside them. This is normal and does not indicate a fault. Wherever possible, use the battery charger in a well-ventilated location. There may be vibration noises from inside the battery charger during use. This is normal and does not indicate a fault. Do not use the battery charger to charge batteries other than rechargeable battery NP-40N. The battery charger could cause interference if placed close to a radio during charging. In this event, move the radio and charger further apart. Do not leave the battery charger in the following types of locations: Extremely humidity or high temperatures, such as close to a heating appliance or in direct sunlight Places with strong vibration In very dusty places The battery charger accepts input voltages of 110-240 V AC at 50 or 60 Hz and can be used all over the world. However, the shape of the plug and socket-outlet depends on the country of use. Consult your travel agent for details.
Specifications Z Standard number of available frames/recording time per xD-Picture Card , SD Memory Card and internal memory The number of available frames and recording time is approximate. The actual number of frames and recording time varies depending on the type of Memory Card or shooting conditions. Also, the number of frames and recording time displayed in the LCD monitor may not decrease regularly.
Quality setting Number of recorded pixels Image data size Internal memory (approx.12 MB) 16 MB 32 MB xD-Picture Card SD Memory Card SDHC Memory Card 64 MB 128 MB 256 MB 512 MB 1 GB 2 GB 512 MB 1 GB 2 GB 4 GB 8 GB iF iN % 2.0 MB KB KB ` 130 KB $ (30 fps) QVGA (30 fps) 20 sec. 27 sec. 54 sec. 110 sec. 221 sec. 7.4 min. 14.8 min. 29.6 min. 59.2 min. 14.3 min. 28.7 min. 57.3 min. 114.8 min. 228.3 min

4.0 MB 2.0 MB 2001 3978

* A movie recording will stop automatically when a movie file becomes approx. 2GB. If you want to continue recording, press
the shutter button again. The available recording time is displayed based on approx. 2GB.
If you shoot using the xD-Picture Cards with model numbers containing M such as DPC-M2GB, movie recording time may be reduced if you repeatedly record and erase (frame erase) image files. In such a case, erase all frames or format the xD-Picture Card before use. Back up important frames (files) onto your PC or another media.

U.A.E.

AFRICA Egypt
Foto Express Egypt Technical support & Repair service Fuji Kenya Ltd Repair service
426 Pyramids St., Giza, Egypt TEL (202) 7762062 FAX (202) 7760169 fotoegypt@access.com.eg P.O.Box 41669-00100, Fuji Plaza, Chiromo Road, Nairobi, Kenya. TEL (254-20)4446265-8 FAX (254-20)4448515 / 7 info@fujifilm.co.ke

Kenya OCEANIA Australia

FUJIFILM Australia Pty Ltd Technical support & Repair service Brijlal & Co. Ltd Technical support & Repair service Phocidis SARL Technical support & Repair service Fujifilm NZ Ltd Technical support & Repair service Oceania PNG Limited Technical support
Locked Bag 5100, Brookvale, NSW, 2100 TEL 355 FAX +61 (2) digital@fujifilm.com.au 70-72 Cumming Street,Suva,Fiji TEL (679)3304133 FAX (679)3302777 kapadia@connect.com.fj 58, rue Higginson - B.P.661 - 98845 TEL (00 687) 25-46-35 FAX (00 687) 28-66-70 phocidis@phocidis.nc Cnr William Pickering & Bush Road Albany, Auckland TEL +64-9-4140400 FAX +64-9-4140410 glenn.beaumont@fujifilm.co.nz Section 15, Allotment 1, Reke St, Boroko NCD. PNG. Mail: PO Box 2167, Boroko NCD. PNG. TEL +FAX +oceania@daltron.com.pg

New Caledonia

New Zealand
Papua New Guinea ASIA Hong Kong
Fuji Photo Products Co., Ltd. Technical support & Repair service
8/F.,TSUEN WAN IND. CENTRE, 220 TEXACO RD., TSUEN WAN, HONG KONG TEL (852)FAX (852)rsd@chinahkphoto.com.hk

Indonesia

PT Modern Photo Tbk Technical support & Repair service FUJIFILM (Malaysia) Sdn. Bhd. Technical support Repair service
Jl.Matraman Raya 12, Jakarta Timur 13150 TEL +2801000 FAX +8581620+2801012 assd_kmr@modernphoto.co.id Letter Box 1, Level 10, 11 & 12, Menara Axis, No 2, Jalan 51A/223, 46100 Petaling Jaya, Selangor Darul Ehsan, Malaysia TEL 603-79584700 FAX 603-79584110 digital@fujifilm.com.my Letter Box 1, Level 10, 11 & 12, Menara Axis, No 2, Jalan 51A/223, 46100 Petaling Jaya, Selangor Darul Ehsan, Malaysia TEL 603-79584700 FAX 603-79584110 technical@fujifilm.com.my 24 Sto. Domingo St., Quezon City 1100, Philippines TEL 632-7436601~06 FAX 632-7324661 digital@yklcolor.com 24 Sto. Domingo St., Quezon City 1100, Philippines TEL 632-7436601~06 FAX 632-7324661 tech_services@yklcolor.com 10 New Industrial Road Fujifilm Building Singapore 536201 TEL 65-FAX 65-service@fujifilm.com.sg 30-1, Mukjeung-dong, Jung-gu, Seoul, Korea TEL +82-2-3282-7363 FAX +82-2-2269-7435 photo@fujifilm.co.kr #301, 3F, Jeonjaland, 16-9, Hangangro3-ga, Yongsan-gu, Seoul, Korea TEL +82-2-701-1472 FAX +82-2-718-1331 1bowl@hanmail.net 2F, Hyeongin Tower, 23-2, Bangyi-dong, Songpa-gu, Seoul, Korea TEL +82-2-2203-1472 FAX +82-2-418-5572 nurijili@hanmail.net

Malaysia

Philippines
YKL Development & Trdg. Corp. Technical support Repair service FUJIFILM (Singapore) Pte Ltd Technical support & Repair service Korea Fujifilm Co., Ltd. Technical support Yonsan AS Center (Fujidigital) Repair service Kangnam AS Center (Digitalgallery) Repair service

Singapore

South Korea South Korea South Korea

South Korea Taiwan

Thailand
Busan AS Center (Digital-Sewon) 241-4, Bujeon-dong, Busanjin-gu, Busan, Korea TEL +82-51-806-1472 FAX +82-51-817-0083 merahan@yahoo.co.kr Repair service No. 38, Min-Chuan E. Rd. Sec. 6, Taipei (114), Taiwan, R.O.C. Hung Chong Corp. TEL 886-2-6602-8988 FAX 886-2-2791-8647 dah@mail.hungchong.com.tw Technical support & Repair service 388 SP Building, 8th Floor, Phayathai, Bangkok 10400 FUJIFILM (Thailand) Ltd. TEL +662-2730029 ext. 755 FAX +662-2730239 supaleark@fujifilm.co.th Technical support Repair service 388 SP Building, 8th Floor, Phayathai, Bangkok 10400 TEL +662-2730029 ext.761,762 FAX +662-2730239 warin@fujifilm.co.th 99-107 Bach Van street, Ward 5, District 5, Ho chi minh city TEL +84-8-8366807 ext.122 FAX +84-8-8380621 diep.phanthithanh@imv.com.vn

Vietnam

International Minh Viet Co., Ltd. Technical support & Repair service
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/products/digital/

Printed in China

Y-709108-PY

Digital Photo ID System

Easy to use Image Intelligence enables great prints every time
ore and m t s hoto ootprin p port mall f Pass n a s i
The Fujifilm FinePix IP-10 Digital Photo ID System is an easy to use system for creating photos for passports, visas and other forms of identification. The system includes the FinePix F480 Digital Camera Kit with a 2nd Lithium Ion battery and the FinePix IP-10 Printer. Designed to support tethered shooting - with the Camera connected to the printer using the provided USB extension cable - the system allows for quick transfer of the photo to the printer without handling a removable digital media card.
The FinePix F480 Digital Camera is a versatile 8.2 MegaPixel camera with 4x optical zoom. It comes with a passport shooting guide on the 2.7 inch LCD. The FinePix IP-10 Printer is a compact printer that uses die sublimination technology and FUJIFILMs Image Intelligence software to produce colorful 4x 6 images. It has a 2.4 LCD for previewing pictures and adjusting print settings.
Choose from 6 different ID layouts - including regulation US passport photos - or print full 4x 6 image

SELECT IMAGE

O K NEXT

BACK RETURN

Printer is Equipped with TV OUT function allowing for LCD images to be displayed on TV screen when connected by video cable
Image Intelligence enables great prints everytime
The FinePix IP-10 printer is equipped with FUJIFILMs proprietary Image Intelligence software. The printer automatically detects faces in the image data and enables optimized face coloring and top-quality prints.
Images of prints and LCD screens are simulated.
FinePix IP-10 Printer Specifications
Printing System Paper Size Print Speed Dye-sublimation thermal transfer (with overcoating) 4 x 6inch 10 x 15cm (10 x 18cm before cutting out) approx. 70 sec. (start of paper feed to finish) Maximum number of printing pixels 300 x 300dpi, CMY with 256 gradations / color
FinePix F480 Camera Specifications
Dimensions Weight Effective Pixels Storage Media Focus Shutter Speed Aperture Sensitivity Exposure Mode LCD Monitor Included Accessories 3.8(W) x 2.2(H) x 0.9(D) 4.9oz. 8.2 Million Pixels Internal memory (approx. 12MB) /xD-Picture Card/SD Media card (xD/SD/SDHC media sold separately) Auto focus (Center) 4 sec. to 1/1500 sec. (depends on exposure) Wide-angle: F2.7 to F5.4 Auto,Equivalent to ISO100/200/400/800 (Standard Output Sensitivity) Programmed AE 2.7-inch , approx.230,000 pixels, Amorphous silicon TFT color LCD monitor, approx. 100% coverage Li-ion battery NP-40N, Battery charger BC-40N, Strap, A/V cable, USB cable, CD-ROM, Owner's manual
PC*2Connection method Supported media
USB xD-Picture card, SD Memory Card (including SDHC), MultiMediaCard, Memory Stick (including Memory Stick PRO), CompactFlash Card
2.4inch LCD AC / Printing: Max-of 60W or less, Standby: Under 0.5W 7.2(W) x 5.8(D) x 2.9(H) inches approx. 2.2lbs. (not including Ink cartridge / Paper tray) TV Terminal, USB Port (Type A: Direct ID / PictBridge Port, Type B: PC Port), DC IN Terminal 35mm x 45mm x 6 prints, 51mm x 51mm x 2 prints, 50mm x 70mm x 2 prints, 60mm x 45mm x 4 prints, 126mm x 85mm x 1 print, 50mm x 38mm x 4 prints. FUJIFILM F-RP 120P Ink Cartridges and Paper refills to produce 120 prints

LCD Monitor Size Power Source / Consumption Dimensions Weight Port and Terminal Connections Possible Customized Frame Sizes / Layout Paper/Ink used
Image Intelligence is a trademark of FUJIFILM Corporation. xD-Picture Card is a trademark of FUJIFILM Corporation. IrSimple and IrSS are trademarks of the Infrared Data Association. Microsoft Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United States and / or other countries. Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries. All other company, organization or product names used in this package are trademarks or registered trademarks of their respective holders. FUJIFILM Corporation.

FUJIFILM U.S.A., Inc.

200 Summit Lake Drive. Valhalla, NY 10595

Ref. no. IP0108

2008 FUJIFILM U.S.A., Inc.