D:\DPF series\2010models\DPF-A73.E73 series\IM\4174749112DPFA73.E72IM_GB\4174749112\4174749112DPFA73.E72IM_GB\01GBDPFA73.E73.UC.CED_IM\010COV.fm Master: Right 010COV.fm Page 1 Sunday, December 27, 2009 7:00 PM

4-174-749-11 (2)

For your safety

Digital Photo Frame

DPF-A73/E73
Lets get the photo frame ready

Lets view an image

Try using various functions

Troubleshooting

Additional information

Operating Instructions

Before operating this unit, please read this manual thoroughly and retain it for future reference.

Owners Record

The model and serial numbers are located at the rear. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. DPF-A73/E73 Serial No. ________________________

2010 Sony Corporation

DPF-A73/E73 4-174-749-11 (2)

WARNING

To reduce fire or shock hazard, do not expose the unit to rain or moisture. Do not expose the batteries to excessive heat such as sunshine, fire or the like.
The number below is for the FCC related matters only.
Regulatory Information Declaration of Conformity
Trade Name: Model No.: Responsible Party: Address: SONY DPF-A73 Sony Electronics Inc. 16530 Via Esprillo, San Diego, CA 92127 U.S.A. Telephone No.: 858-942-2230 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION

Replace the battery with the specified type only. Otherwise, fire or injury may result. Dispose of used batteries according to the instructions.
For the customers in the U.S.A.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
Declaration of Conformity
Trade Name: Model No.: Responsible Party: Address: SONY DPF-E73 Sony Electronics Inc. 16530 Via Esprillo, San Diego, CA 92127 U.S.A. Telephone No.: 858-942-2230 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. If you have any questions about this product, you may call: Sony Customer Information Services Center 1-800-222-SONY (7669)

For the State of California, USA only
Perchlorate Material - special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate Perchlorate Material: Lithium battery contains perchlorate.
For the Customer in Europe
This product has been tested and found compliant with the limits set out in the EMC Directive for using connection cables shorter than 3 meters (9.8 feet).

Attention

The electromagnetic fields at the specific frequencies may influence the picture of this digital photo frame.

Notice

If static electricity or electromagnetism causes data transfer to discontinue midway (fail), restart the application or disconnect and connect the communication cable (USB, etc) again.
conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery will be treated properly, hand over the product at end-of-life to the applicable collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the applicable collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.
Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product. Applicable Accessories: Remote control

Notice for the customers in the countries applying EU Directives
The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.
NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM
A moulded plug complying with BS 1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a fuse of the same rating as the supplied one and approved by ASTA or BSI to BS 1362, (i.e.marked with or mark) must be used. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.
Disposal of waste batteries (applicable in the European Union and other European countries with separate collection systems)
This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste. On certain batteries this symbol might be used in combination with a chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are added if the battery contains more than 0.0005% mercury or 0.004% lead. By ensuring these batteries are disposed of correctly, you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery. The recycling of the materials will help to

Notice for users

Program 2010 Sony Corporation Documentation 2010 Sony Corporation All rights reserved. This manual or the software described herein, in whole or in part, may not be reproduced, translated or reduced to any machine readable form without prior written approval from Sony Corporation. IN NO EVENT SHALL SONY CORPORATION BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, WHETHER BASED ON TORT, CONTACT, OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL, THE SOFTWARE OR OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF. Sony Corporation reserves the right to make any modification to this manual or the information contained herein at any time without notice. The software described herein may also be governed by the terms of a separate user license agreement. Any design data such as sample pictures provided in this software cannot be modified or duplicated except for the purpose of personal use. Any unauthorized duplication of this software is prohibited under copyright law. Please note that unauthorized duplication or modification of portraits or copyrighted work could infringe the rights reserved by rights holders.

Read this before using

Notes on playback
Connect the AC adaptor to an easily accessible AC outlet. Should you notice an abnormality in it, disconnect it from the AC outlet immediately.

Notes on copyrights

Duplication, edition, or printing of a CD, TV programs, copyrighted materials such as pictures or publications, or any other materials except for your own recording or creation is limited to private or domestic use only. Unless you hold copyright or have permission of copyright holders for the materials to be duplicated, use of those materials beyond this limit may infringe the provisions of the copyright law and be subject to the copyright holders claim for damages. When using photo images with this digital photo frame, pay special attention not to infringe the provisions of the copyright law. Any unauthorized use or modification of others portrait may also infringe their rights. For some demonstrations, performances, or exhibits, photography may be forbidden.
Recording contents are not guaranteed
Sony shall assume no responsibility for any accidental or consequential damages or loss of the recording contents which may be caused by use or malfunction of the digital photo frame or memory card.

Backup recommendations

To avoid potential risk of data loss caused by accidental operation or malfunction of the digital photo frame, we recommend that you save a backup copy of your data.
On the illustrations and screen shots used in this manual
The illustrations and screen shots used in this manual are of the DPF-A73 unless noted otherwise. The illustrations and screen shots used in this manual may not be identical to those actually used or displayed.

Notes on LCD screen

Do not press against the LCD screen. The screen may be discolored and that may cause a malfunction. Exposing the LCD screen to direct sunlight for a long period may cause malfunctions. The LCD screen is manufactured using extremely high-precision technology, so over 99.99% of the pixels are operational for effective use. However, there may be some tiny black points and/or bright points (white, red, blue or green in color) that constantly appear on the LCD screen. These points are normal in the manufacturing process and do not affect the viewing in any way. Images may trail across on the LCD screen in a cold location. This is not a malfunction.

Table of Contents

Read this before using... 4
Checking included items.... 7 Identifying the parts.... 8 Digital photo frame.... 8 Remote control.... 9
Remote control.... 10 Stand.... 10 To display the photo frame on the wall... 11 Turning the photo frame on... 12 Operations in an initial state... 13 Setting the current time... 14
Inserting a memory card... 15 Changing the display... 16 About the information displayed on the LCD screen.. 17
Various functions... 18 Specifying the playback device... 19 Adjusting image size and orientation (Zoom in/Zoom out/Rotate).. 19 Changing the settings of the auto power on/off function. 20 Changing the settings... 21 Connecting to a computer... 22

Continued

If an error message appears...23 If trouble occurs....23

Precautions....25

Installation.... 25 Cleaning.... 25 Restrictions on duplication... 25 Disposing of the photo frame...25 Specifications....26 On trademarks and copyrights...27

Checking included items

Make sure that the following items are included. Digital photo frame (1)

Stand (1)

Attaching to the screw hole (.page 10)
Remote control (1) Removing the protective sheet (. page 10)
AC adaptor (1) Connecting to the AC power source (.page 12)
Exchangeable panels (DPF-E73 only) Operating Instructions (this manual) (1) CD-ROM (Digital Photo Frame Handbook) (1) Warranty (1) (In some regions, the warranty is not supplied.)
The supplied CD-ROM contains the Digital Photo Frame Handbook that explains operations and setups of the digital photo frame in detail. To view the handbook, insert the CD-ROM into the computer and double-click the Handbook icon. (To display the handbook, you need Adobe Acrobat Reader. )

Identifying the parts

x Digital photo frame
LCD screen Remote sensor Sony logo (DPF-A73 only) (.page 10)
VIEW MODE button (.page 16) 1 (on/standby) button Standby indicator MENU button Direction (B/b/v/V) buttons, ENTER ( ) button
BACK button Access lamp Memory card slot (.page 15) Holes for hanging unit on the wall Space for storing the stand
USB B connector (.page 22)
Stand (.page 10) DC IN 5 V jack (.page 12)

x Remote control

VIEW MODE buttons 1 (on/standby) button SLIDE-SHOW ( CLOCK ( ) button SINGLE button ) button INDEX ( MENU button Zoom in ( ) button Direction (B/b/v/V) buttons BACK button SELECT DEVICE button IMPORT ( ROTATE ( ) button DELETE ( ) button ) button ENTER ( ) button ) button

Zoom out ( ) button

About descriptions in this manual The operations described in this manual are based on remote control operation. When an operation is performed differently, for example, with the remote control and the buttons on the photo frame, it will be explained in a tip.

P Notes

If the remote control stops working: Replace the battery (CR2025 lithium battery) with a new one. When the lithium battery becomes weak, the operating distance of the remote control may shorten, or the remote control may not function properly. In this case, replace the battery with a Sony CR2025 lithium battery. Use of another battery may present a risk of fire or explosion.

Remote control

Pull out the protective sheet before use as shown in the figure.

Protective sheet

Replacing procedures:
.CD-ROM (Handbook) page 9

P WARNING

Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire.
Using the remote control Point the top end of the remote control towards the remote sensor on the photo frame.
z Tips x When the photo frame is placed in the portrait orientation
If you set the photo frame with its operations buttons facing upwards, the display is also automatically rotated to the portrait orientation.
Screw the stand into the screw hole firmly until the stand stops turning.

x Sony logo

(DPF-A73 only) When the photo frame is placed in the portrait orientation or when you turn off the power, the Sony logo doesn't light up.
You can set the photo frame to portrait or landscape orientation by rotating it without moving the stand.
To display the photo frame on the wall

PNotes

Use screws suitable for the quality of the material of the wall. The screws may be damaged, depending on the type of material used in the wall. Set the screws in a pillar or stud in the wall. When you want to re-insert the memory card, remove the photo frame from the wall, then eject and re-insert the memory card while the photo frame is placed on a stable surface. Remove the stand and store it in the space for storing the stand provided on the rear when you hang the photo frame on the wall.
Prepare screws (not supplied) suitable for the screw holes on the rear panel.
4mm (3/16 inch) More than 25mm (1 inch) 4.2mm (3/16 inch) 8.6mm (11/32 inch) Holes for hanging the unit on the wall
Screw the screws (not supplied) into the wall.
Be sure the screws (not supplied) protrude between 2.5 to 3mm (1/8 inch) from the surface of the wall.
Since a magnet is contained in the space for storing the stand, you can keep the stand attached to the portion. Connect the DC cable of the AC adaptor to the photo frame and hang the photo frame on the wall. Then connect the AC adaptor to the wall outlet. We take no responsibility for any accidents or damage caused by defects of attachment, misuse, or natural disasters, etc.

Between 2.5mm to 3mm (1/8 inch)
Hang the photo frame on the wall by fitting the hole on the rear panel to the screws on the wall.
The socket outlet should be as close as possible to the unit, and easily accessible. Do not place the photo frame on an unsteady or tilted surface. Connect the AC adaptor to an easily accessible wall outlet close by. If trouble occurs while using the adaptor, immediately shut off the power by disconnecting the plug from the wall outlet. Do not short the plug of the AC adaptor with a metal object. Doing so may cause a malfunction. Do not use the AC adaptor placed in a narrow space, such as between a wall and furniture. Insert the plug of the AC adaptor firmly, if the connection is loose, the photo frame may turn off when it is moved. After use, remove the AC adaptor from the DC IN 5 V jack of the photo frame, and remove the AC adaptor from the outlet. Do not turn the photo frame off or disconnect the AC adaptor from the photo frame before the standby indicator turns red. Doing so may damage the photo frame. The AC plug may be removed from the AC adaptor main unit by pushing the PUSH tab. When using the AC adaptor, however, you do not have to remove the AC plug. Make sure to use the AC adaptor with the AC plug firmly attached. If the AC plug is removed, slide it into the AC adaptor main unit until it clicks into place as illustrated. The AC plug shape may differ depending on the region you purchase the photo frame.
Turning the photo frame on
Insert the plug of the AC adaptor into the DC IN 5 V jack on the rear of the photo frame. Connect the AC adaptor to the wall outlet.
The photo frame is automatically turned on.
To the DC IN 5 V jack DC plug DC cable AC adaptor main unit AC plug To wall outlet
When the AC plug is removed

Attaching the AC plug

Attach the AC plug to the AC adaptor main unit as follows:
PUSH tab clicks when the AC plug is slid firmly into place.
Removing the AC plug from the wall outlet If the AC plug remains inserted in the wall outlet, remove it as follows, without using a tool:

Metal terminals at the rear of the AC plug.
If handled roughly, the AC plug may become detached from the AC adaptor main unit and remain in the wall outlet. If this occurs, grasp the AC plug with dry hands as illustrated and remove it from the wall outlet. Do not use a tool. Be careful not to touch the metal terminals at the rear of the AC plug. Check to see if there is no trouble with the AC adaptor main unit and AC plug, and then slide the AC plug into the AC adaptor main unit until it clicks into place. If there is any problem with the AC adaptor main unit or AC plug, consult with your Sony service facilities for repair.
Operations in an initial state
When the photo frame is turned, the initial display appears.
zTips x If the photo frame is not operated
If the photo frame is not operated for 10 seconds, the demo mode is displayed.
x Releasing the demonstration mode
If any other button than the power button is pressed, the screen returns to the initial display.

Setting the current time

The B/b buttons become activated only when the Clock and calendar view mode (page 16) is not selected.
Press MENU, and B/b to select the
v/V [Date/time Settings] , (ENTER)

(Settings) tab.

Press v/V to select [Time] ,

(ENTER).

v/V to select a value. , B/b (hour, minute, and second) (ENTER) Setting complete. ,

Press MENU.

In the same window, you can use the same procedures as time setting to set the following: Setting items Date Date Display Order (Y-M-D/M-D-Y/D-M-Y) First day of the week (Sunday/Monday) 12hr/24hr display (12 hours/24 hours)

Inserting a memory card

Insert the memory card firmly into the corresponding slot with its label side facing toward you (when you are facing the back side of the photo frame).
When using a memory card of the following types, make sure to insert it in an appropriate adaptor. If you insert it without an adaptor, you may be unable to remove it. As shown in the right-most illustration below, make sure to insert the following types of memory cards with inserted in the appropriate adaptor.

xD-Picture Card (Slot A)

1miniSD /miniSDHC

SD memory Card (Slot A)

miniSD/ miniSDHC adaptor

2microSD/microSDHC

Memory Stick (Slot A)
microSD/ microSDHC adaptor

3Memory Stick Micro

Memory Stick Duo (Slot B)
M2 adaptor (standard size)

z Tips x Importing

The number of images to be saved in the internal memory: Resize: approx. 250 images Original: the number of images may vary, depending on the original image file size.

Various functions

Importing an image (a memory card b the internal memory) Exporting an image (the internal memory b a memory card) Deleting an image

x Exporting

Any memory card that is not recognized by this photo frame is shown in gray and you cannot select it.
When a desired image is displayed, press MENU and then B/b to select the (Editing) tab. Select the desired menu item (Import/Export/Delete), and press (ENTER). Press v/V to select [. this image]/[. multiple images]/[. all images], and press (ENTER).
(. stands for each command: Import, Export, or Delete.) [. this image]: Press v/V to select the destination, and press (ENTER).
PNotes x During exporting/deleting
Avoid doing the following. Doing so may damage this photo frame, memory card, or the data: Turning off the power Removing an memory card Inserting another card

x When deleting

If deletion has started, the deleted image cannot be recovered even if you stop deletion.
[. multiple images]: Press B/b/v/V to select a desired image in the image list, and then press (ENTER) to add. Repeat this operation to select multiple images.
To clear the selection: Select the image and press (ENTER). disappears from the image. After you finish selecting the images, press MENU and then select the destination. [. all images]: All the images are displayed with. Press MENU and then select the destination.
Press v/V to select [Yes], and press
Specifying the playback device
Press SELECT DEVICE. Press v/V to select the playback device, and then press (ENTER).
z What is playback device?
A memory card or the internal memory.

P Note

During Clock and calendar display, you cannot select the (Select device) tab.
Adjusting image size and orientation (Zoom in/Zoom out/Rotate)

Enlarging/Reducing

Press (zoom in) or (zoom out).
Saving an enlarged or a reduced image (Crop and save) When you move the enlarged image with B/b/v/V and press MENU, the image is saved in the trimmed size. You can select the saving method by pressing v/V. Saving methods: [Save as new image], [Overwrite]* * JPG and JPEG images only
Enlarging an image may reduce the quality depending on the image size. It is not possible to enlarge an image using the buttons on the photo frame.

Rotating

Press Or: (ROTATE).
An enlarged image cannot be rotated.
Press MENU, B/b to select the (Editing) tab, v/V to select [Rotate], and then press (ENTER). Press v/V to select the direction to rotate, and then press (ENTER).
: Rotates the image 90 degrees clockwise. : Rotates the image 90 degrees counterclockwise.
When displaying the images in the internal memory, the information used to rotate the image is retained even after the power is turned off.

Press v/V to select [OK], and then press
Changing the settings of the auto power on/off function
z Tips x During operation
The power is turned off automatically at the time you set for [Power-OFF timer].
Press MENU, B/b to select the
Press v/V to select [Auto Power ON/OFF], and then press (ENTER).
x During the standby mode
The power is turned on automatically at the time you set for [Power-ON timer].
1 Press v/V to select [Power-ON timer] or [Power-OFF timer]
2 Press v/V to select [Enable] , (ENTER). 3 [Auto ON time]/ [Auto OFF time] setting

v/V: Set the time.

AM or PM is displayed when you select [12 hours] on the time display setting. 4 [Auto ON day] / [Auto OFF day] setting v/V: Add a check mark to select the day on which you want activate the timer. Move the cursor to [OK] and press (ENTER).

Changing the settings

Press MENU, then B/b to select the (Settings) tab.
Depending on the status on the photo frame, some settings of some items cannot be changed. They are displayed in gray and cannot be selected. During Clock and calendar display, you can make settings in the (Settings) tab only.
Press v/V to select the item and setting value, and then press (ENTER).

Setting items

Slideshow Settings Auto Power ON/OFF Date/time Settings General Settings (Listing Order, Sony logo ON/OFF* etc,.) * Turning on the Sony logo is the function only available for DPF-A73. Language Setting Initialize

Connecting to a computer

Use a B-Type USB cable.* * When you use a commerciallyavailable USB cable, use a USB cable with a B-type plug (for the USB B connector of this unit, frame-side connector type) shorter than 3 meters. If multiple USB devices are connected to a computer or if a hub is used, a problem may occur. In such a case, simplify the connection. You cannot operate the photo frame from another USB device being used simultaneously. Do not disconnect the USB cable during data communication. Operation with all computers that satisfy the recommended system requirements is not guaranteed. The photo frame has been demonstrated as operable when connected to a computer and a Sony digital photo printer. When other devices are connected to the photo frame, these devices may not recognize the internal memory of photo frame.
Connect the AC adaptor to the photo frame, and to the AC power source. Connect the computer and photo frame with a commercially available USB cable. Turn the photo frame on. Operate the computer to exchange images with the internal memory of the photo frame.

To USB B connector

Computer

To USB connector

x Windows
Recommended OS: Microsoft Windows 7/Windows Vista SP2 / Windows XP SP3 Port: USB port

x Macintosh

Recommended OS: Mac OS X (v10.4 or later) Port: USB port
If an error message appears
Error message Cannot delete a protected file. Meaning/Solutions To delete a protected file, cancel the protection on your digital camera or computer.
Memory card is protected. Remove The memory card is write-protected. Slide the writeprotection then try again. protect switch to the enable position. (.Digital Photo Frame Handbook, page 42) Error reading the Memory Stick. / Error reading the SD Memory Card. / Error reading the xDPicture Card./Error reading the iternal memory. Write error on the Memory Stick. / Write error on the SD Memory Card. / Write error on the xDPicture Card./ Write error on the internal memory. For a memory card: An error has occurred. Check that the memory card is inserted correctly. If this error message is displayed frequently, check the status of the memory card with a device other than the photo frame. For the internal memory: Initialize the internal memory.
Note When you initialize the internal memory, please note that all the image files imported to the internal memory are deleted.
Memory card format not supported. For a memory card, use your digital camera or other device to format the memory card.
Note When you initialize the memory card, all the files on the memory card will be deleted.

If trouble occurs

Symptom Some images are not displayed. Check item Are the images displayed in the index view? Does the mark displayed below appear in the index view? Cause/Solutions c If the image is displayed in the index view but cannot be displayed as single image, the image file may be damaged even though its thumbnail preview data is fine. c A file that is not compatible with DCF may not be able to be displayed with the photo frame, even if it can be displayed with a computer. c If a mark is displayed, the thumbnail data or image itself cannot be opened. c The photo frame can play, save, delete, or otherwise handle up to 4,999 image files.
Are there more than 4,999 images in the memory card?
Symptom Some images are not displayed.

Check item

Cause/Solutions
Did you rename the file with c If you named or renamed the file on your a computer or other device? computer and the file name includes characters other than alphanumeric characters, the image may not be able to be displayed on the photo frame. Is there a folder with more than 5 levels in its hierarchy on the memory card? c The photo frame cannot display images saved in a folder that is more than 5 levels deep. c If you do not make a folder, you can only save up to 512 images. In addition, the number of images may be reduced depending on the file name length or character type. When you save images in the internal memory from a computer, be sure to make a folder in the internal memory and save the images in this folder. c Use the device you are using to cancel write-protection and try deleting again. c Slide the write-protect switch to the enable position. c Check the image information from the single view mode. (.page 17) c An image with a mark is set to Read Only. You cannot delete it on the photo frame. c Turn off and then on the power. (.page 12) c Replace the battery. (.Digital Photo Frame Handbook, page 9) c Insert a battery in the proper orientation. (.Digital Photo Frame Handbook, page 9) c Point the top end of the remote control towards the remote sensor on the photo frame. c Remove any obstruction between the remote control and the remote sensor. c Remove the protective sheet. (.page 10)

D:\DPF series\2010models\DPF-A73.E73 series\IM\4174749112DPFA73.E72IM_GB\4174749112\4174749112DPFA73.E72IM_GB\01GBDPFA73.E73.UC.CED_IM\080ADD.fm Master: Left 080ADD.fm Page 26 Sunday, December 27, 2009 7:03 PM

Specifications

x Photo frame
LCD screen LCD panel: DPF-A73/E73: 18cm/7.0-inch, TFT active matrix Total number of dots: DPF-A73/E73: 336,960 (480 3(RGB) 234) dots Effective display area Display aspect ratio: 16:10 LCD screen area: DPF-A73/E73: 16.3cm/6.4-inch Total number of dots: DPF-A73/E73: 303,264 (432 3(RGB) 234) dots LCD backlight life 20,000 hours (before brightness of the backlight is reduced to half) Input/Output connectors USB connector (TypeB, Hi-Speed USB) Slots Memory Stick PRO (Standard/Duo)/SD memory card/MMC/ xD-Picture Card slot Compatible image file formats JPEG: DCF 2.0 compatible, Exif 2.21 compatible, JFIF*1 TIFF: Exif 2.21 compatible BMP: 1, 4, 8, 16, 24, 32 bit Windows format RAW (preview only*2): SRF, SR2, ARW (2.0 or lower version) (Some image file formats are not compatible.) Maximum number of pixels that can be displayed 8,000 (H) 6,000 (V) dots *3 File system FAT12/16/32, sector size of 2,048 bytes or smaller
Image file name DCF format, 128 characters within 5th hierarchy Maximum number of files that can be handled 4,999 files for a memory card Internal memory capacity*MB (Approx. 250 images*5 can be saved.) Power requirements DC IN jack, DC 5V Power consumption
Model DPF-A73/E73 in operation mode including the AC adaptor at the maximum load normal mode* 7.0 W 6.8 W
* The definition of the normal mode is a status which allows the performance of a slideshow using images stored in the internal memory with the default settings without inserting a memory card or connecting an external device.
Operating temperature 5 C to 35 C (41 F to 95 F) Dimensions DPF-A73/E73: [With the stand spread out] Approx. 115.2 mm (8 3/5/5/8 inches) (width/height/depth) [When the photo frame is hanging on the wall]: Approx. 39.3 mm (8 3/5/9/16 inches) (width/height/depth) Mass DPF-A73: Approx. 435 g (15.3 oz) DPF-E73: Approx. 450 g (16 oz) (excluding the AC adaptor) Included accessories See Checking included items on page 7.