FT-2000 Series FT-2000D FT-2000
200 W Version with External Power Supply 100 W Version with Internal Power Supply
High-performance Receiver Design utilizing System-wide Gain and Intercept Balancing
Triple-conversion Receiver Design with Optimized Stage Balance
Designed with the same emphasis on efficiency as used with a transmitter, the receiver design of the FT-2000 is centered around optimization of each stage's gain, intercept, and selectivity. The triple-conversion design features a 1st IF of 69.45 MHz, a 2nd IF of 450 kHz, and a 3rd IF of 30 kHz (FM: 24 kHz), and each stage's advanced filtering protects the stages to follow from unwanted signal voltage, leading to a quiet, ultra-robust receiver with impeccable total system performance.
Preamp 2 (which adds the second preamplifier stage in series), according to the antenna in use and the noise and interference conditions present at the time. The low noise figure and carefully-controlled stage gains ensures that only the precise amount of gain needed is actually utilized. IPO (Intercept Point Optimization) is the function which allows you to set the total front end gain, so as to optimize RF stage performance. The ultra-strong first mixer of the FT-2000 features SPM5001 FETs in an active, doubly-balanced configuration optimized for a multi-signal environment. The active design results in no net loss in the mixer circuit, often eliminating the need for preamplification prior to direct feed of received signals to the first mixer.
Yaesus renowned engineering know-how is now applied to the world of IF DSP, and the FT-2000s 32-bit floating point IF DSP is crafted to give your station the edge over all other DSP-based radios
Dual Receive (In-band) Featuring Independent IF Strips
The sub receiver of the FT-2000 is an analog type, with a completely independent IF section so that strong signals appearing on the main receiver do not affect signals on the sub receiver. This brings you the true benefits of dual receive operation. The IF passband of the sub receiver may be varied between 2.4 kHz and 1.1 kHz, and an optional Collins Mechanical Filter of 500 Hz (YF-122C) or 300 Hz (YF-122CN) may be added, for sharper selectivity on CW.

Main VFO-A 2nd IF

450 kHz AGC 1st IF AMP CF 2nd IF AMP 3rd Local DET ADC FILTER AGC DET DAC
Robust Receiver Front End
The RF amplifier stage is designed for low and high intercept, utilizing two strong series-connected 2SC3356 bipolar transistors with negative feedback for consistent, repeatable performance. The front-panel IPO switch lets you select direct feed to the first mixer (IPO), Preamp 1, or

Front End

1st IF

69.450 MHz

IPO "ON" ROOFING FILTER

3rd IF (DSP)

30 kHz DSP
The IF Digital Signal Processing system of the FT-2000 is based on the TI TMS320C6713 32-bit floating point DSP IC.
World-renowned Variable IF WIDTH and IF SHIFT Interference-reduction Systems
The IF Shift system is highly effective for removing interference. While leaving the pitch of the incoming signal unchanged, as well as the bandwidth of the IF passband, the IF Shift system allows you to vary the passband higher or lower in frequency, eliminating interference that you tune outside the passband. The IF Shift control is concentric with the IF WIDTH control. The Variable IF WIDTH system has a default center bandwidth of 2.4 kHz for SSB and CW, and 500 Hz for RTTY and PSK operation. By rotating the IF WIDTH control the passband maybe reduced to as little as 25 Hz on CW/RTTY/PSK, or 200 Hz on SSB. What's more, if you like to listen in a wider bandwidth for greater fidelity on SSB, the SSB bandwidth may be expanded to 4000 Hz by simply rotating the IF WIDTH control clockwise.
IF WIDTH Conceptual Diagram
Standard Passband Modified Passband

OPTION

Manual IF Notch and Beat-reducing Automatic Digital Notch Filter (DNF)
The IF Notch features very high Q, producing a deep notching effect typically in excess of 70 dB. Using the Menu mode, either a "Wide" or "Narrow" notch filter can be selected, depending on the interference profile you are encountering. To aid in tuning such a high-Q filter with precision, concentric [COARSE] and [FINE] tuning controls for the IF Notch are provided, yielding the ability to adjust the Notch filter precisely yet effortlessly. And, for reduction of multiple carriers within the passband, the DSP Auto Notch (DNF) filter may be engaged, independently from the manual Notch Filter.

ATT ANTENNA SELECTOR

RF AMPk/6 k/15 k 1st Local RF AMP2

2nd Local

40.455 MHz

ROOFING FILTER

Sub VFO-B 2nd IF
455 kHz AGC CF 2nd IF AMP DET

BPF Unit

1st IF AMP 1st Local 15 k

Front End Block Diagram

3rd Local Collins Mechanical Filter (option)

IF NOTCH Performance

PMFIR Log Magnitude -10 -20 -30 -40 -50 -60 -70 -80 -90
Variable RF Preselector (VRF) Covers the 1.8 - 28 MHz Amateur Bands
To provide protection for the RF stages, as well as the three IF stages, the front end filtering system utilizes a combination of twelve fixed bandpass filters and Yaesu's exclusive VRF (Variable RF) Preselector system. These two RF filter systems protect the early stages of the receiver from overload caused by strong out-of-band signals. The highQ VRF system, much narrower in bandwidth than the fixed bandpass filters, are crafted using high-permeability toroidal coils (T-80 and T-37 type) and tuning capacitors, producing 44 tuning steps for optimal of broadcast or commercial-service interference. The robust circuit design utilizes expensive sealed surface-mount relays, capable of sustaining surges of up to 2500 Volts down the antenna line. The center frequency of the VRF is manually adjustable, allowing you to skew the filter response for maximum rejection of the undesired signals. VRF Unit

VRF Frequency Response (3.5 MHz)
First IF 3 kHz Roofing Filter is Factory Installed
The 69.450 first IF of the FT-2000 features three roofing filters, in bandwidths of 15 kHz, 6 kHz, and 3 kHz, optimized by mode for best performance on todays crowded bands. Each roofing filter is a four-pole, fundamental-mode monolithic crystal filter design to produce excellent shape factor. Especially useful during busy contest weekends, the roofing filters are positioned right after the first mixer, improving IP3 (3rd-Order Intercept Point) performance for all stages that follow.
IF SHIFT Conceptual Diagram
Three-section Roofing Filter Stage
3 kHz Roofing Filter Performance
REF -14.0 dBm Log 10 dB/ ATT 00 dB
Min 200 Hz/25 Hz Mid 2.4 kHz/500 Hz Max 4 kHz/2.4 kHz 20 Hz Step 1kHz

FREQUENCY kHz

RBW 10 kHz VBW 10 kHz

IF WIDTH

IF SHIFT
DSP Digital Noise Reduction
For reduction of random noise types, the FT-2000 utilizes a powerful Digital Noise Reduction filter, which contains sixteen different noise analysis parameters specially created after hundreds of hours of on-theair testing. The operator may choose any of these parameters to reduce noise most effectively, based on noise conditions at any given time.
Digital Noise Reduction Performance
MKR(250):1.555kHz A MAG OUTPUT 0.0dBm SWT 230s IRG 0dBm RBW 10Hz VBW 100Hz DRG 400ms

SWP 50 ms

SPAN 500 kHz

CENTER 69.450 MHz

10dB/Div 50 kHz/Div
High-speed Direct Digital Synthesizer (DDS) and 200 MHz High-spec Digital PLL for Outstanding Local Oscillator Performance
In seeking to improve the strong-signalhandling capabilities of the receiver section, in a multi-signal environment, the YAESU design team has developed a highspec, ultra-low-noise local oscillator system that produces a very clean first IF signal. The high Carrier-to-Noise (C/N) ratio of the 200 MHz high-speed digital PLL is the result of very fast lock time, because the local design does not entail the use of a prescaler but rather locks directly on the 1st local frequency. As a result, the spuriousfree dynamic range and close-in blocking performance are substantially enhanced.
Local Oscillator Block Diagram
TCXO DDS PLL VCO VCO DDS DDS LPF LPF VCO VCO AMP LPF
Passband Response CONTOUR Control with an Analog Touch
The incredibly sharp "brick wall" filters of the IF DSP system can expose characteristics of incoming signals that you've never heard before, not all of them pleasant to listen to. But, using the CONTOUR control, you can roll off low-frequency or highfrequency components so as to shape the receiver passband differently, or null out part of the mid-range area, with continuous adjustment CONTOUR Filter Conceptual Diagram throughout the passband. By nulling out interfering or irrelevant frequency components, the desired frequency components are allowed to rise out of the background noise, improving fidelity and signal-to-noise ratio.

CONTOUR

1st Local

2nd Local 3rd Local

VRF: Graphic Representation of Center Frequency Position
VRF 3.75 MHz REF -9.4 dBm 10 dB/

ATT 10dB

START:10Hz

STOP:3.1kHz

Analog-sounding High-quality Digital SSB Modulation
The FT-2000 utilizes a phase-shift digital modulation technique that not only provides a analog-sounding high-quality digital SSB modulation envelope, but it also allows the transmission bandwidth to be adjusted by the operator.
RBW 100 kHz VBW 30 kHz SWP 50 ms

SPAN 15 MHz

CENTER 7.5 MHz

10dB/Div 2 MHz/Div

C/N Performance 10dB/Div 1 kHz/Div
Unlock the Secrets of the Low Bands
YAESU's Exclusive, Fully-Automatic -Tuning Preselector System!

Quick Split Feature

Pressing the [SPLIT] key for two seconds or more engages the "Quick Split" feature, which automatically separates the receive and transmit frequencies by 5 kHz (the TX frequency will be 5 kHz higher). For other Split operating situations, just press the combination LED/switches near each VFO dial to set the VFOs as you want them.
Superb Viewing and Display Clarity, in the FT DX 9000 Tradition
High-accuracy Analog Meter
In order to ensure maximum accuracy in power and other measurements, an oversized, crystal-clear analog system is used on the FT-2000. With excellent contrast and illumination provided by white LEDs, the analog meter system may be toggled for viewing of Speech Processor Compression level, ALC level, SWR, final amplifier voltage, and final amplifier current.

Tracking Feature

During Split operation, you may command the FT-2000 to operate in a "Tracking" mode whereby the Sub VFO frequency tracks the frequency change on the Main VFO, maintaining a constant split between the two frequencies. You can even do "Band Tracking" whereby you can cause both bands to change simultaneously, using this feature.
TXW (Transmit Frequency Watch) Feature
When operating Split, pressing the [TXW] key instantly lets you receive on your transmit frequency, to hear activity in the pile-up you are working to break through.

Preset NARROW Switch

While the WIDTH control is generally used for setting of the IF DSP bandwidth, a one-touch [NARROW] key is provided, allowing you instantaneous access to a bandwidth narrower than the default value on the current operating mode. For SSB, for example, where the default bandwidth is 2400 Hz, you have "Narrow" selections available of 200/400/600/850/1100/1350/1500/1650/1800/1950/2100/2250 Hz, while on CW, "Narrow" selections of 25/50/100/200/300/400/500/800/1400/1700/ 2000 Hz are available. So, for example, you can set up "Narrow" bandwidths of 1.8 kHz for SSB, 500 Hz for CW, and 300 Hz for RTTY and PSK operation. What's more, for AM Broadcast operation, you may use the [NARROW] key to toggle between bandwidths of 6 kHz and 9 kHz, depending on interference.

The oversized VFD display provides higher brightness and contrast compared to TFT displays, allowing clearer viewing from a wider range of angles than on other transceivers. The Main band frequency is shown in bright blue, while the Sub band is shown in white, for instant recognition.
Narrow SSB 1.8kHz CW 500Hz
SSB/CW 2.4kHz RTTY/PSK 500Hz AM 9kHz AM 6kHz FM 16kHz FM 9kHz RTTY/PSK 300Hz

TO FROM

-Tune MTU-80/40

-Tune MTU-30/20

DIN DIN DIN DIN DIN DIN
Unique "Block Diagram" Display Shows Receiver System Status Instantly
The upper left area of the display contains a unique Block Diagram display, showing the current status of a number of functions in the receiver of the FT-2000. Included in the displays are Antenna selection, Front-end Attenuator, Preselector (VRF or -Tune), Preamplifier selection, Roofing Filter selection, and AGC response time. You also get Bar Graphs depicting several different DSP filter settings, for quick alignment.

IF Noise Blanker

The IF Noise Blanker is ideal for suppression of automotive ignition noise, and it may be utilized in conjunction with the Digital Noise Reduction system, or by itself. A front-panel Noise Blanker gain control allows precise control of the blanking level to be applied, and both wide and narrow pulse noises may be suppressed using this feature.

FT-2000 Rear

-Tune Circuit Functional Diagram
VFO Dial -T Dial Controller/Tuning Data Memory
Control Circuit RF -Tuning Kit Connection Diagram

BAND Stepping Motor Core

Sloped AGC Feature
During certain conditions whereby both weak and strong signals are being encountered, a "flat" AGC response (whereby signals above a certain level are all clamped so as to produce the same audio output) may not be optimal. So the FT-2000 menu lets you select a traditional "flat" response or a "Sloped" response, whereby louder signals are allowed to rise up to a slightly higher level than are weak signals, thereby allowing you to use your brain to discriminate between signals according to signal strength, not just frequency characteristics. This provides superior signal recognition during contest pile-up operating situations.

SLOPED/NORMAL AGC Conceptual Drawing Sloped Output
Position Sensor Marker Probe Position Sensor Position Sensor
Independent Analog Clarifier Display
For effortless offset tuning with a completely analog feel, the RX and TX Clarifiers included in the FT-2000 are an operator's dream come true. Whether operating a modest split in a DX pile-up, or compensating for some stations in a local ragchew being off frequency, The Clarifier system of the FT-2000 is simple to operate, and the offset display, both numerical and graphic, is easy to read, with one-touch resetting to a "zero" value, if desired.
Normal (Traditional AGC) AGC Start
Input 10dB/Div 2 MHz/Div Large-Area (1/1"/28 mm) Coil (Actual Size) Clarifier Dial and Keys

The Joy of Operating.

Ultra-Clean Transmitter Design

Actual Size

Flywheel-effect Oversized High-quality Main Tuning Dial
The front panel's oversized 2.67" (68 mm) Main Tuning Knob is
crafted using a heavy brass alloy (knob weight: 6.7 oz./190 g), for easy flywheel-effect frequency excursions or precision tuning of weak digital signals, thanks to the precision magnetic rotary-encoder tuning mechanism coupled to the Main Tuning Knob. The torque of the tuning knob shaft may be adjusted, by rotating the Main tuning Knob while holding the dial skirt, for just the amount of drag you prefer. All it will take is one spin of the dial for you to know that you are in command of a serious radio. The Main Tuning Dial is the same structure as used on the FT DX 9000, utilizing the normal dial structure along with a rotating skirt that creates a small air gap. This air gap reduces sweat accumulation on the operator's fingertips, enhancing tuning precision during long operating sessions, especially on DX-peditions to hot tropical areas.
Just as on the FT DX 9000, the most important switches for operational control are arrayed around the Main Tuning Knob, making the FT-2000 and ergonomic delight. Included are memory control, narrow filter selection, QMB (Quick Memory Bank) keys, and VFO selection and command keys surrounding the knob, with operating mode selection in the next row to the left.
Interference-reduction Controls are Arrayed on the Right Side of the Front Panel
The most important interference-reduction controls, including VRF/-Tune adjustment, IF Shift, IF Bandwidth, Contour, DNR, IF Notch, and DNF are all arrayed close to each other on the right side of the front panel, so your hands never need to wander far when battling tough QRM.
High-power, Super-stable Final Amplifier Stage
The FT-2000 incorporates a pair of reliable RD100HHF1 MOS FETs in a push-pull configuration, using a supply voltage of 13.8 Volts. They are cooled using a hugs 1400 cc die-cast aluminum heat sink with a high coefficient of thermal conductivity. A thermostatically-controlled 3.6"/92mm axial cooling fan engages at 40 C, and it features five speeds, depending on the degree of cooling required. The large bearing surface of the fan, its "floating" mount, and the unique heat sink design combine to make the cooling system ultra-quiet, yet very efficient.

With the FT-2000, you can use both your ears and your eyes to zero in on another CW station. The sidetone generated when you transmit (as set by the CW Pitch selection, with a range of 300-1050 Hz), allows you to match that pitch to that of an incoming signal perfectly. As you tune closer and closer to that pitch, the CW Tuning Indicator provides a graphical depiction of the tuning process, with a marker lighting up when the incoming signal is precisely aligned with yours.
Leading-edge Features for the Serious Operator
Contest-ready Antenna Selection Capabilities
The FT-2000 is designed with today's fast-moving contest operator in mind. Two TX/RX antenna jacks are provided on the read panel, along with one RX-only jack, with one-touch access to any antenna. The antenna selection is memorized in each VFO and memory channel register, so you don't need to switch antennas when changing VFOs the radio remembers which antenna you last used on that band or memory! And, if you have a special bandpass or other filter you want to engage, "In" and "Out" jacks for the RX-only path are also provided.

CS Key

The CS (Custom Selection) key, located below and to the left of the Main tuning Dial, lets you select any Menu item for one-touch access via the CS key. This lets you bring up a favorite Menu item without having to scroll through the many available Menu selections.

And Much, Much More.

Quick Memory Bank (QMB) for instant storage and recall of frequency/mode information when you're in a hurry Digital voice Recorder for storage of 15-seonc "loop" of incoming receiver audio Four-channel message memory for repetitive voice messages ("CQ Contest.), with each channel capable of storing up to 20 seconds of audio. With the optional FH-2 Keypad, 5 channels may be stored Optional FH-2 Keypad provides message storage and recall of voice and CW messages, along with remote control functions VOX (Voice-operated TX/RX control). MOX (Manual TX/RX control) All-mode Squelch 50-tone CTCSS Encoder/Decoder for FM operation Band-Specific Repeater Shifts for 29/50 MHz FM Wide/Narrow modes for AM and FM LOCK feature Flexible, easy-to-use VFO/Memory command selections: A B, A B, V/M, M A, A M Memory Channel Offset Tuning (MT) Versatile Scanning Capability Versatile Menu Mode for customization of setup and features Constant-level rear-panel sound recording jack Comprehensive external RS-232C computer control (CAT) protocol The front panel of the FT-2000 includes control keys allowing you to control the speed and direction of a YAESU G-800DXA, G- 1000DXA, or G-2800DXA rotator (supported rotators current as of September 2006), with front panel display of these parameters

Speed Indication (0% - 100%) Direction Indication (0 - 360)Counter-clockwise Rotation Speed Up
Antenna Jacks ANT 1 Antenna Switches

TX/RX Relay TX RX

Transmitter Circuit

ANTENNA 1/2 RX

CW Spot Feature
The CW SPOT switch engages a spotting tone that matches the offset of your transmitted signal (as set by the CW Pitch selection), allowing you to match that pitch to that of an incoming signal perfectly. There's no more powerful way to be sure youre exactly on frequency.
RX ANT OUT External Receiver

FILTER Pre-AMP

RX-only Antenna Switch
Parametric Microphone Equalizer
The Three-Band Parametric Equalizer provides the FT-2000 user with simply unmatched capability to equalize a microphone and voice characteristics optimally. Within each of the three bands (low-frequency, mid-range, and high-frequency) provided, you may adjust the center frequency of the equalization, the bandwidth over which the equalization is applied, and the amplitude (either peaking or nulling) within that range. Independent Equalizer settings are provided for when the DSP Speech Processor is on and off.
Parametric Equalizer Frequency Response
+10dB Bandwidth/Gain (Q) Level (dB)

RX Antenna

RX ANT IN
Receiver Circuit Antenna Switching Circuit
Built-in TCXO for State-of-the-Art Stability
A highly-stable Temperature-Compensated Crystal Oscillator (TCXO) is built into every FT-2000, providing 0.5 ppm stability at room temperature, and better than 1 ppm stability over an ambient temperature range of 14 to 122 F (-10 to +50 C), making the FT-2000 ideal for PSK31, EME or other applications requiring high stability.
Additional CW Capabilities

OCXO Frequency Stability

Gain/Loss
Separate KEY jacks on the front and rear panels Built-in Electronic Keyer with 4-60 WPM Speed control Electronic Keyer Weight control Keyer paddle Dot-Dash reversal "Bug" keying emulation CW Full Break-in Four-channel Message Memory (50 characters each); five memories
available with optional FH-2 Keypad

Frequency Drift (Hz)

0 -1 -2 -3

-10 -55 60

EXT CONTROL OPERA TION ADJ. MODE MODE SELECT SWITCH FULL SCALE ADJ OV ERLAP LE ADJ D A PRESET ADJ B OUT VOL ADJ
"Overlap" Indication

Clockwise Rotation

Speed Down

Rotator Controller

Renowned YAESU Speech Processor for that Contest or DX Pile-up Punch
The power of IF DSP is brought to the world of Speech Processing, with the powerful new DSP Speech Processor design incorporated into the FT-2000. Crafted to increase intelligibility at the receiving side of a difficult path, the Speech Processor includes its own set of Parametric Equalizer settings, so the optimum frequency response may be obtained. The compression level for the Speech processor may be adjusted from the front panel.

Automatic insertion of incrementing contest number into stored messages Automatic "Beacon" keyer mode CW "VOX" Delay is adjustable: 20 ms 5000 ms CW Mode reversal (USB or LSB injection) CW keying available during SSB operation

Temperature C

EXT CONTROL
"My Bands" Feature
In order to increase operating efficiency, you may use the Menu system to command the FT-2000 "skip" over any Amateur bands on which you do not operate (because you dont have an antenna for that band, etc.). For example, for contest operation, you do not need to use the 10/18/24 MHz bands, so you may eliminate them from the band stepping sequence, if you like.
1.9MHz 3.5MHz 7MHz 10MHz 14MHz 18MHz 21MHz 24MHz 28MHz 50MHz

Rotator Control Cable

Transmit Monitor Feature
The IF Transmission Monitor allows you to listen to a faithful reproduction of the transmitters IF signal, for making precise adjustments to the Parametric Equalizer, SSB Bandwidth, and/or Speech Processor. The Monitor Level may be adjusted from the front panel.

Menu Mode

3.5 3.5MHz 7MHz 14MHz 21MHz 28MHz
Low-level Transverter Interface Jack
The rear panel of the FT-2000 includes a low-level (0.1 mW) output jack ideal for connecting to VHF and UHF transverters.
Select by Customized Band
Flexible and Easy Connection Points for RTTY, SSTV, PSK31, JT65 (EME) and other Digital Modes Optional VL-1000 Quadra System Linear Amplifier provides fullyautomatic operation General coverage reception: 30 kHz 60 MHz (specifications guaranteed only in Amateur bands) Mode-optimized Automatic AGC decay selection (OFF/SLOW/MID/FAST) Versatile Memory system: 99 channels and up to 5 Memory Groups Four-position receiver front-end attenuator (0/6/12/18 dB) for operation on noisy bands or when very strong signals are present

REMOTE CONTROL

Optional External Data Management Unit (DMU-2000) provides Wide Display Capabiblities
A wide array of informative and useful displays, identical to those available on the FT DX 9000D, can be obtained by adding the optional DMU-2000 Data Management Unit and an after-market display (not supplied) and your own personal computer. Enjoy the ultimate in operating ease by adding the DMU-2000!
Audio Scope/Oscilloscope Display Page
When you have connected your after-market monitor to the DMU-2000 the Audio Scope and Oscilloscope "page" of the display may be the most-used capability of the Data Management Unit. The Audio Scope portrays the audio spectrum of either the receiver passband or your transmitted signal, allowing you to visualize the frequency components as you hear them. Then you can make adjustments to, for example, the Notch Filter, Contour control or (on transmit) the Parametric Microphone Equalizer. At the same time, you may use the Oscilloscope to look at the X-Y characteristics of an incoming signal, with variable level and sweep speed. The Audio Scope also includes a two-speed "Waterfall" display that is very useful for precise tuning of digital signals, or for Notch Filter adjustments.

World Clock Page

The World Clock page includes a world map with entries for a number of locations throughout the world, so you can know what the time of day is anywhere. Of great usefulness to DXers is the Sunrise/Sunset depiction, which shows the "Gray Line" area where propagation frequently is enhanced. An alarm feature is also included, to alert you of a schedule time.

Spectrum Display

Rotator Control Page
The Rotator Control page lets you control the left/right rotation of your Yaesu G-800/1000/2800DXA series rotator, in addition to permitting speed control and setup of preset beam headings. And, if you use your after-market keyboard for input of your latitude and longitude, the DMU-2000 will lay out and display a Great Circle Map centered on your location! You may also connect a GPS Unit (one capable of output of NMEA0183 position data) to your DMU-2000 in order to download precise position data. The Great Circle Map allows you to aim your antenna accurately, and the imbedded database of worldwide cities may be used to determine a specific bearing to a DX location, if you like.

Waterfall Display

Swept-Frequency SWR Page
Photograph shows 100-Watt version. Computer display and keyboard are after-market items, not supplied with the FT-2000.
As you tune across the Amateur band and transmit at different frequencies, the DMU-2000 will plot the SWR across the band, alerting you to any unusual SWR situations, etc.
DMU-2000 Data Management Unit (option)

Spectrum Scope with LBWS

The RF Band Scope allows you to view activity within a span of 25 kHz, 100 kHz, 250 kHz, 500 kHz, 1 MHz, or 2.5 MHz, depending on your requirements, with a fixed sweep speed for seamless transition between spans. Additionally, the YAESU-exclusive LBWS (Limited Band Width Sweep) allows you to reduce the bandwidth to 50%, 30%, or 10% of the original, imparting a corresponding increase in the sweep speed, if you like. By sweeping just a limited portion of the main Band Scope at high speed, you get a superbly detailed view of activity in that segment of the overall band, allowing you precise zero-in capability not found on competing products. With a 50% reduction, you get double the speed; with reduction to 30% of the original sweep, you get a 3X increase in speed, and by reducing the bandwidth to 10% you gat a whopping 10X increase in the sweep speed. You can use the <- and -> keys to move the remaining window, as desired.

Memory Channel List

The 99 available memories may be grouped into as many as five Memory Groups, and all these memories may be viewed on the Memory Channel Listing page. You may add an alpha/numeric "Tag" to each memory, as well, for quick recall of the channel's identification.

Log Book Feature

By connecting an after-market keyboard and monitor to the DMU2000, you can utilize the on-board Logging capability of the FT-2000. The Log Book includes an extensive database of DX information, and you may archive log data to the supplied CF card using one of the popular logging formats like ADIF, Cabrillo, etc.

Inside the DMU-2000

Rear Panel (100-Watt version)

RX ANT OUT

Receive Antenna Output Jack

Options

ANT 1/2 Jacks
Antenna Jacks ("M"/SO-239 type)

DC OUT

Internal DC Power Source Output Cable Jack
117 VAC (10 A) AC Power Cable Receptacle
Fuse Holder Main Power Switch DC13.8V

Input Terminal

SP-2000 External Speaker with Audio filters
The SP-2000 features a large (4.7/120 mm) speaker aperture, along with a three-selection High-Cut and two-selection Low-Cut Audio Filter system. Selection of the cutoff frequencies may be performed from the front panel of the speaker: 2.4 kHz/1 kHz/700 Hz for High-Cut, and 500/300 Hz for Low Cut. A headphone jack is provided on the front panel, allowing you to connect headphones and enjoy the benefits of the audio filtering within the SP-2000.
Receive Antenna Input Jack

RTTY (FSK) Data Jack

+13.8 V Jack TX GND Jack TX REQ Jack EXT ALC

External ALC Input Jack

Grounding Post

PACKET

Packet (AFSK) Data Jack

EXT SPKR

External Speaker Jack

KEY CAT DMU

DMU-2000 Interconnection Jack CW Key Jack External Computer Control Jack (RS-232C)

RF -Tune Kits

160m Band RF -Tune Kits A 80/40m Band RF -Tune Kits B 30/20m Band RF -Tune Kits C
-Tune Unit Connection Jack (RF)

BND (BAND) DATA

Band Data Jack (for connection to VL-1000 Linear Amplifier, etc.)

REM (REMOTE)

FH-2 Interconnection Jack

Sound Recording Jack

AF OUT
Constant-level Audio Output Jack (1V, 10 k Impedance)

ROT (ROTATOR)

YAESU Rotator Interface Jack (Models G-800DXA, G-1000DXA, and G-2800DXA)
Transverter Interface Jack (50 , 0.1 mW)
-Tune Unit Connection Jack (for Tuning Data)

Includes

Scope Unit CF Card Unit

MIC (PATCH) PTT

External PTT Input Jack

DMU-2000

Data Management Unit

Top View

Bottom View
After-market PS/2 Keyboard and personal computer monitor are required for use of DMU-2000 and are not supplied.
Up to three -Tune Kits may be connected. -Tune Kit is included in purchase price of -Tune Unit.
Sub Receiver Mechanical CW Filters

(One may be installed)

Collins
YF-122C (500 Hz) YF-122CN (300 Hz)

MD-200A8X

Desktop Deluxe Dynamic Microphone

MD-100A8X

Desktop Microphone

YH-77STA

Stereo Headphones
HF-50 MHz 1 KW Linear Amplifier (50 MHz: 500 W/USA Version)

VL-1000 Power Supply

Remote Control Keypad

VL-1000

Automatic Antenna Tuner Built In

VP-1000

Supplied Accessories: MH-31B8 Hand Mic, AC Cable, RCA Plugs (2), 3.5 mm Mono Plug (1) 3.5 mm Stereo Plug (1), 1/4" (6 mm) Stereo Plug (1), 4-pin DIN Plug (1), 5-pin DIN Plug (1).

Specifications

FT-W Version FT-2000D 200 W Version

Circuit Type

FT-W Version FT-2000D 200 W Version Receiver Specifications
Main (VFO-A); Triple-conversion superheterodyne Sub (VFO-B); Double-conversion superheterodyne Intermediate Frequencies Main (VFO-A); 69.450 MHz/450 kHz/30 kHz (24 kHz for AM/FM), Sub (VFO-B); 40.455 MHz/455 kHz Sensitivity (RF AMP 2 "ON") SSB (2.4 kHz, 10 dB S+N/N) 2 V (0.1 - 1.8 MHz) 0.2 V (1.8 - 30 MHz) 0.125 V (50 - 54 MHz) AM (6 kHz, 10 dB S+N/N, 30 % modulation @400 Hz) 6 V (0.1 - 1.8 MHz) 2 V (1.8 - 30 MHz) 1 V (50 - 54 MHz) FM (BW: 15 kHz, 12 dB SINAD) 0.5 V (28 - 30 MHz) 0.35 V (50 - 54 MHz) Selectivity Main (VFO-A) Mode -6 dB -60 dB CW/RTTY/PKT 0.5 kHz or better 750 Hz or less SSB 2.4 kHz or better 3.6 kHz or less AM 6 kHz or better 15 kHz or less FM 15 kHz or better 25 kHz or less (WIDTH: Center, VRF: OFF) Sub (VFO-B) Mode -6 dB -60 dB CW/RTTY/PKT 1.1 kHz or better 3.0 kHz or less SSB 2.2 kHz or better 4.5 kHz or less AM 6 kHz or better 25 kHz or less FM 12 kHz or better 30 kHz or less Image Rejection 70 dB or better (160 - 10m Amateur bands) 60 dB or better (6m Amateur band) Maximum Audio Output 2.5 W into 4 Ohms with 10% THD Audio Output Impedance 4 to 8 Ohms (4 Ohms: nominal) Conducted Radiation Less than 4000 W
General Specifications Rx Frequency Range 30 kHz - 60 MHz (operating) 160 - 6 m (specified performance, Amateur bands only) Tx Frequency Ranges 160 - 6 m (Amateur bands only) Frequency Stability 0.5 ppm (@77 F/25 C) Operating Temperature Range 14 F ~ +122 F (10 C ~ +50 C) Emission Modes A1A (CW), A3E (AM), J3E (LSB, USB), F3E (FM), F1B (RTTY), F1D (PACKET), F2D (PACKET) Frequency Steps 1/10 Hz (SSB, CW, & AM), 100 Hz (FM) Antenna Impedance 50 Ohms, unbalanced 16.7 - 150 Ohms, unbalanced (Tuner ON, 160 - 10 m Amateur bands) 25 - 100 Ohms, unbalanced (Tuner ON, 6 m Amateur band) Power Consumption Rx (no signal) 70 VA (@117 VAC) Rx (signal present) 80 VA Tx (100 W) 450 VA Tx (200 W) 720 VA Supply Voltage AC: 90 VAC - 132 VAC or 180 VAC- 264 VAC DC: 13.8 V 10 % Dimensions (WxHxD) 16.1" x 5.3" x 13.8" (410 x 135 x 350 mm) Weight (approx.) 33 lbs (15 kg) 38.5 lbs (17.5 kg) Transmitter Specifications Power Output 5 W ~ 100 W 10 W ~ 200 W 2 W ~ 25 W (AM) Class-A (SSB) 10 W ~ 75 W 5 W ~ 50 W (AM) Modulation Types J3E (SSB): Balanced, A3E (AM): Low-Level (Early Stage), F3E (FM): Variable Reactance Maximum FM Deviation 5.0 kHz/2.5 kHz Harmonic Radiation Better than -60 dB (160 - 10m Amateur bands) Better than -70 dB (6m Amateur band) SSB Carrier Suppression At least 60 dB below peak output Undesired Sideband Suppression At least 60 dB below peak output Audio Response (SSB) Not more than -6 dB from 300 to 2700 Hz 3rd-order IMD -31 dB (14 MHz 100 W) -31 dB (14 MHz 200 W) -45 dB (14 MHz 75 W Class-A) Microphone Impedance 600 Ohms (200 to 10 kOhms)

8/24/07

(*text revised 9/5/08)

This procedure is used to update EDSP software for the FT2000/2000D transceivers.
We recommend installing the Flash Programming Software on a PC computer with Windows 2000, XP or Vista Operating System; and use the RS-232C, DB9F to DB9F straight cable. ADVICE: If you have a previous version the EDSP software, we recommend you update to the latest version v0140 software (MAIN CPU) before you update the EDSP software to version 10-29. Go to the YAESU website FT-2000 files section for the software and instructions: FT-2000/D Update Software v0140 (9/5/08)* FT-2000/D Update Software Information v0140 (9/5/08)*
Ver. 10-29 implements improvements:
Improve the FM transmit audio.
The software updates will work with all versions (AF, AS, EU, NA, OC, SA or all Countries) of the FT-2000 and FT-2000D.

PART 1

Install the programming data file software to your PC 1. Down load the FT-2000 data file [EDSP3(K)08-22-07.zip] from the following website: http://www.yaesu.com/indexVS.cfm?cmd=DisplayProducts&ProdCatID=102&encProdID=6 6EA91711DFB68C03DED4AD35153E12C&DivisionID=65&isArchived=0 2. Save the FT-2000 data file [EDSP3(K)08-22-07.zip] to a temporary folder on your hard drive. 3. Unzip and Extract the contents of EDSP3(K)08-22-07.zip to the desktop or the local disk C:\temp folder on your computer. 4. The programmer and data software are now stored on your computer in the drive and folder designated in the last step above. They are ready to update your FT-2000 or FT-2000D Transceiver.

PART 2

*This procedure is used for uploading new EDSP Software into the FT-2000 and FT-2000D Amateur Transceivers, from your personal computer, using the RS-232C, DB9F to DB9F straight cable. 1. Turn off the main power switch located on the back of the FT-2000 (or turn off the power supply for FT-2000D) and remove the AC power cord. 2. Connect a serial RS-232C, DB9F to DB9F straight cable to the COM1 connector of your computer and the 9-pin CAT connector on the rear of the transceiver. (If you use a USB to serial adapter, you might need to change the com-port number.

Main Power SW CAT

3. Reconnect the power cable and turn ON the main power switch located on the back of the FT2000 (or turn ON the power supply for FT-2000D). 4. While holding the [DNR][CONT][DNF] buttons, press the front main power switch to turn the radio on. You will see [dSP Prg NO 1] on the radio display.
5. On your computer desk top or in the local disk C:\temp folder where you stored the files extracted from EDSP3(K)08-22-07.zip, find the folder named V10-29 and open the file [EDSP3exe].

Edsp3.exe

6. You will see the screen shown below open on your computer.
7. Click the Update button. You will see v1029 out file displayed. Click v1029 out file to highlight it. Then click the Open button and wait until the program is loaded, and 100% is indicated on the bar graph, [completion!!] will be displayed. 8. Turn the front Power Switch and the Main Power Switch in the back OFF (This resets the radio and locks in the new software). Remove the DB9F to DB9F cable. The updating process is now complete

The software version can be displayed on the radio
While holding the three buttons [GEN][50][ENT] turn the radio on. The software version will be displayed in the VFO-A window for 5 seconds 10.29 1.40 and then the radio will start up in normal operation. Example: 10.29 1.40 EDSP v10-29, Main v0140.
Software version 10.29 Main CPU: Software version
We hope this new software will increase your enjoyment of your FT-2000/D. Thank you for choosing Yaesu radios. If you have any problems or questions please contact Vertex Standard, Amateur Tech Support. amateurtech@vxstdusa.com Best 73, mm
NOTE: Our documents have listed the software in some different ways. For example v0140, v1.40 and v1-40 as used in these instructions and information are referring to the same version of software.