Please keep all information for future reference. Guarde toda informacin para tener como referencia futura.
Safety Precautions Before trying to use the piano, be sure to read the separate Safety Precautions. Precauciones de seguridad Antes de intentar usar el piano, asegrese de leer las Precauciones de seguridad separadas.

PX130ES1A

Espaol
USERS GUIDE GUA DEL USUARIO

English

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
IMPORTANT SAFETY INSTRUCTIONS
1. 2. 3. 4. 5. 6. 7. 8. 9. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. The power indicator being unlit does not mean the apparatus is completely disconnected from the MAINS. When you need to have the apparatus completely disconnected from the MAINS, you must unplug the power cord. For that purpose, locate the apparatus in a way that secures easy access to the power cord.

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.
Declaration of Conformity
Model Number: PX-130 Trade Name: CASIO COMPUTER CO., LTD. Responsible party: CASIO AMERICA, INC. Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801 Telephone number: 973-361-5400 This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Important!

Please note the following important information before using this product. Before using the AD-A12150LW Adaptor to power the unit, be sure to check the AC Adaptor for any damage first. Carefully check the power cord for breakage, cuts, exposed wire and other serious damage. Never let children use an AC adaptor that is seriously damaged. The product is not intended for children under 3 years. Use only CASIO AD-A12150LW adaptor. The AC adaptor is not a toy. Be sure to disconnect the AC adaptor before cleaning the product.

Manufacturer: CASIO COMPUTER CO.,LTD. 6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan Responsible within the European Union: CASIO EUROPE GmbH Casio-Platz 1, 22848 Norderstedt, Germany
This mark applies in EU countries only.

Contents

General Guide.. E-2
FUNCTION Button.. E-3 Saving Settings and Using Operation Lock. E-3 To configure settings with the keyboard.. E-19 Keyboard Keys Used for Configuring Settings.. E-20 Parameter List... E-21 Reverb.. E-21 Chorus.. E-21 Tone selection.. E-21 Brilliance (BRILLIANCE).. E-21 Layer balance... E-21 Tempo (TEMPO)... E-21 Song select (SONG SELECT). E-21 Song volume (SONG VOLUME).. E-21 Metronome volume (METRONOME VOLUME).. E-21 Metronome beat (METRONOME BEAT).. E-21 Keyboard key (Transpose). E-22 Keyboard tuning (Tuning).. E-22 Octave shift.. E-22 Temperament (TEMPERAMENT).. E-22 Temperament select (TEMPERAMENT SELECT).. E-22 Temperament Base note (BASE NOTE).. E-22 Touch response (TOUCH RESPONSE). E-22 USB device mode (USB DEVICE MODE). E-23 Send channel.. E-23 Local control... E-23 Operation tone.. E-23 Back up... E-23 Operation lock... E-23

Power Outlet.. E-4

Using an AC Adaptor.. E-4

Connections.. E-5

Connecting Headphones.. E-5 Connecting Audio Equipment or an Amplifier. E-5 Connecting a Pedal.. E-6 Bundled and Optional Accessories.. E-6
Playing with Different Tones. E-7
Selecting and Playing a Tone.. E-7 To adjust the brilliance of a tone.. E-8 Layering Two Tones... E-9 Using Effects... E-10 Using the Metronome.. E-10 Playing a Piano Duet.. E-11
Playing Back Built-in Songs.. E-13
Playing Back All of the Built-in Songs.. E-13 Playing Back a Specific Music Library Song. E-13 Practicing with a Music Library Song. E-14
Recording and Play Back.. E-15
Tracks... E-15 To record to a specific track of a song.. E-16 To record to one track of a song while listening to the playback of the other track.. E-17 Playing Back from Digital Piano Memory. E-17 Deleting Recorded Data.. E-18
Connecting to a Computer. E-24
Minimum Computer System Requirements. E-24 Connecting the Digital Piano to Your Computer. E-24 Using MIDI... E-25 Transferring Song Data with a Computer. E-25

Reference... E-28

Troubleshooting... E-28 Product Specifications.. E-29 Operating Precautions... E-30

Appendix.. A-1

Tone List... A-1 Song List... A-1
MIDI Implementation Chart
Company and product names used in this manual may be registered trademarks of others.
Configuring Settings with the Keyboard... E-19

General Guide

Left Side

Bottom

Installing the Music Stand
Insert the bottom of the music stand into the groove on the top of the digital pianos console.
The names shown here are always indicated in bold when they appear within the text of this manual. 1 VOLUME controller 2 FUNCTION button 3 SONG a, DEMO button 4 RECORDER (L) button 5 METRONOME (R) button 6 GRAND PIANO (MODERN), REVERB button 7 GRAND PIANO (CLASSIC), CHORUS button 8 ELEC PIANO, DUET button 9 USB port bk DAMPER PEDAL jack bl DC 12V terminal bm POWER button bn PHONES jacks bo Pedal connector

FUNCTION Button

The FUNCTION button is used when configuring a variety of different digital piano settings. The following are FUNCTION button basics. To change a setting, hold down the FUNCTION button as you press the keyboard key that is assigned the setting you want to select. An operation confirmation tone will sound whenever you press a keyboard key to configure a setting. Example: To select a tone on page E-7
For details about operations and settings, see Configuring Settings with the Keyboard on page E-19. The following table shows how pressing the FUNCTION button changes the operation of certain buttons.
This button: SONG a RECORDER METRONOME MODERN CLASSIC ELEC PIANO Does this while FUNCTION button is depressed: Starts and stops demo tune play. Selects the left-hand part. Selects the right-hand part. Toggles Reverb on (button lamp lit) and off (lamp unlit). Toggles Chorus on (button lamp lit) and off (lamp unlit). Toggles Duet on (button lamp lit) and off (lamp unlit).
Saving Settings and Using Operation Lock
Your digital piano lets you save its current settings and lock its buttons to protect against operation errors. For details, see Parameter List on pages E-21 - E-23.

Power Outlet

Your digital piano runs on standard household power. Be sure to turn off power whenever you are not using the digital piano.

AC Plug Configurations

Depending on the geographic area, your digital piano may come with a second AC plug. Use the AC plug that matches the configuration of the wall outlet in your area. The AC adaptor is shipped from the factory with one of the AC plugs shown below installed.

Using an AC Adaptor

Use only the AC adaptor (JEITA Standard, with unified polarity plug) that comes with this digital piano. Use of a different type of AC adaptor can cause malfunction of the digital piano. Specified AC Adaptor: AD-A12150LW

AC adaptor AD-A12150LW

To change the AC plug
Perform the following steps when you need to change the AC plug that is installed on the AC adaptor.
Slide the plug in the direction of the arrow in Figure 1, and remove it from the AC adaptor. Align the plug that matches the power outlet of your area with the AC adaptor slots. Slide it in place in the direction of the arrow shown in Figure 2. Press the part indicated by the arrow in Figure 3 until the plug clicks securely into place.

Figure 1

DC 12V terminal

Household power

Note the following important precautions to avoid damage to the power cord. During Use Never pull on the cord with excessive force. Never repeatedly pull on the cord. Never twist the cord at the base of the plug or connector. The power cord should not be stretched tight while it is in use. During Movement Before moving the digital piano, be sure to unplug the AC adaptor from the power outlet. During Storage Loop and bundle the power cord, but never wind it around the AC adaptor.

IMPORTANT!

Figure 2

Figure 3

Never connect the AC adaptor (JEITA Standard, with unified polarity plug) that comes with this digital piano to any other device besides this piano. Doing so creates the risk of malfunction. Make sure the digital piano is turned off before plugging in or unplugging the AC adaptor. The AC adaptor will become warm to the touch after very long use. This is normal and does not indicate malfunction.
Should the AC plug come off of the AC adaptor, slide it back on as shown in the illustration. Slide the AC plug along the rails on the AC adaptor as far as it will go, until it locks securely in place.

Connections

Whenever connecting something to the digital piano, first use the VOLUME controller to set the volume to a low level. After connecting, you can adjust the volume to the level you want.

Connecting Headphones

Left side
PHONES jacks Commercially available headphones
You can connect audio equipment or a music amplifier to the digital piano and then play through external speakers for more powerful volume and better sound quality.

SP-32 Pedal Functions

Damper Pedal In addition to the damper pedal functions described in the column to the left, the SP-32 pedal also supports half-pedal operation, so pressing the pedal part way applies only a partial damper effect. Soft Pedal Pressing this pedal suppresses notes played on the keyboard after the pedal was pressed, and makes them sound softer. Sostenuto Pedal Only the notes that are played while this pedal are depressed are sustained until the pedal is released.

DAMPER PEDAL jack

Soft Pedal Sostenuto Pedal SP-3

Damper Pedal

The optional CS-67P stand is required in order to use the SP-32 Pedal Unit.

Pedal Connector

You can connect the optionally available 3-Pedal Unit (SP-32) to the pedal connector on the bottom of the digital piano. You can then use the pedals for expression that is similar to that available on an acoustic piano.
Bundled and Optional Accessories
Use only accessories that are specified for use with this digital piano. Use of unauthorized accessories creates the risk of fire, electric shock, and personal injury.

Pedal connector

You can get information about accessories that are sold separately for this product from the CASIO catalog available from your retailer, and from the CASIO website at the following URL. http://world.casio.com/
Playing with Different Tones

SONG a GRAND PIANO

Selecting and Playing a Tone
The piano comes with 16 built-in tones.
The names of the tones are marked above the keyboard keys to which they are assigned.

To select a tone

Press the POWER button.
When you turn on the digital piano, it performs a power up operation in order to initialize its system. During system initialization the tone button lamps cycle on and off in the sequence for about seven seconds to let you know that system initialization is in progress.
Select the tone you want.
To select GRAND PIANO (MODERN or CLASSIC) or ELEC PIANO Press one of the GRAND PIANO buttons (MODERN or CLASSIC) or the ELEC PIANO button to select the one you want. To select one of the other tones While holding down the FUNCTION button, press the keyboard key that corresponds to the tone you want to select.
The button lamp of the selected tone will light.
Use the VOLUME controller to adjust the volume.

VOLUME

FUNCTION

METRONOME

ELEC PIANO
GRAND PIANO tones (MODERN, CLASSIC) Your digital piano has a total of 16 built-in tones. The MODERN and CLASSIC tones are stereo sampled tones that can be selected using the GRAND PIANO buttons. Try using the GRAND PIANO tones to familiarize yourself with their distinctive sounds and characteristics.

Tone Name MODERN Characteristics This tone provides a bright grand piano sound. The volume and timbre of this tone is quick to respond to different keyboard pressures, and it has relatively strong reverb. This tone is a good choice for dynamic and lively performances. This is a natural piano tone that closely resembles the sound of an acoustic grand piano. Reverb and other effects are kept to a minimum in order to enhance the impact of piano pedals operations (acoustic resonance), for musically delicate expressions. This tone is a good choice for lesson and practice sessions.
To adjust the brilliance of a tone
While holding down the FUNCTION button, use the BRILLIANCE keys to specify a brilliance value in the range of 3 to 0 to 3.

CLASSIC

For this type of sound: Mellower and softer Brighter and harder

Press this keyboard key:

The GRAND PIANO tone (VARIATION) is best for playing along with an accompaniment.
Bass Tones (BASS 1, BASS 2)
Selecting either of the two BASS (LOWER) tones (1 or 2) in step 2 of the above procedure will assign the selected bass tone to the low range (left side) of the keyboard. The high range (right side) will be assigned the tone that was selected when you pressed the BASS 1 or BASS 2 key. BASS 1 and BASS 2 let you effectively split the keyboard between two different tones.
Split Point Low Range High Range
To return a tone to its initial default setting 0, press and at the same time.

BASS 1

PIPE ORGAN (Currently selected tone.)
To return the keyboard to a single tone, select any tone other than BASS 1 or BASS 2. You cannot select BASS 1 or BASS 2 when recording to Track 2.

Layering Two Tones

Use the following procedure to layer two tones, so they sound at the same time. When specifying two tones for layering, first tone you select will be the main tone, while the second tone will be the layered tone.
To adjust the volume balance between two layered tones
While holding down the FUNCTION button, use the keyboard keys shown below to adjust the volume of the layered tones.
While holding down the FUNCTION button, hold down the keyboard key for the main tone as you press the keyboard key for the layered tone.
Example: To layer HARPSICHORD and STRINGS 1

C1 C2 C3 C4 C5 C6 C7 C8

Initial default (Center) Volume of the layered tone (Second tone you selected) Volume of the main tone (First tone you selected)
To return the volume setting to its initial default, hold down the FUNCTION button and press both of the keys at the same time.

HARPSICHORD STRINGS 1

To unlayer the keyboard, select another tone by pressing the GRAND PIANO button or by using the procedure under Selecting and Playing a Tone (page E-7).
You also can layer piano tones by holding down one of the GRAND PIANO buttons (MODERN or CLASSIC) as you press the ELEC PIANO button. You cannot layer the BASS 1 or BASS 2 tone with another tone. You cannot perform the layer operation when recording to Track 2.

To adjust the metronome volume
You can perform the following procedure at any time, regardless of whether or not the metronome is sounding.
Select the piano tone you want to use for the duet.
Example: GRAND PIANO (MODERN)
While holding down the FUNCTION button, use the METRONOME VOLUME keys to specify a volume value in the range of 0 to 42.
For details about using the keyboard keys for settings, see Keyboard Keys Used for Configuring Settings on page E-20. Each press of the or key raises or lowers the metronome volume value by 1.
While holding down the FUNCTION button, press the ELEC PIANO button to toggle duet on (lamp lit) and off (lamp unlit).
You cannot use the Duet Mode while recording (page E-15).
To return to the initial default setting, press at the same time.
While holding down the FUNCTION button, use the TEMPO keys to specify a tempo value in the range of 20 to 255 beats per minute.

Playing a Piano Duet

You can use the Duet Mode to split the pianos keyboard in the center so two people can play a duet. This makes it possible to configure the keyboard so, for example, the teacher can play on the left and the student can follow along on the right. Or one person can play the left hand part on the left, while another plays the right hand part on the right.
Changing the Octaves of the duet keyboards
You can change the ranges of the left and right keyboards in octave units from their initial default settings. This comes in handy, for example, if the initial default range is not enough when one person is playing the left hand part and another person is playing the right hand part.
While holding down the FUNCTION and ELEC PIANO buttons, press the keyboard C key that you want located at C4 (middle C) of the left keyboard.
Example: Press the keyboard key of the leftmost C (C4)
will assign the range shown below.
Left keyboard Right keyboard
(Pressed key) 1 octave higher than initial setting Unchanged
While holding down the FUNCTION and ELEC PIANO buttons, press the keyboard C key that you want located at C4 (middle C) of the right keyboard.
You can return the keyboards to their initial default ranges by exiting and then re-entering the Duet Mode.
Playing Back Built-in Songs

SONG a METRONOME

Your digital piano comes with a Music Library of 60 built-in tunes. You can play all 60 tunes in sequence, from beginning to end.
Playing Back a Specific Music Library Song
The Music Library includes both built-in songs (01 to 60), plus one song (61) that have been saved to digital piano memory from a computer*. You can use the procedure below to select one of these songs and play it back. * You can download music data from the Internet and then transfer it from your computer to digital piano memory. See Transferring Song Data with a Computer on page E-25 for more information.
After you select a built-in song, it can take a number of seconds for the song data to be loaded. While the data is being loaded, the keyboard keys and button operations will be disabled. If you are playing something on the keyboard, the following operation will cause output to stop.
Playing Back All of the Built-in Songs
Find the song number of the song you want to play in the song list on page A-1. To change to another song, hold down the FUNCTION button as you use the SONG SELECT keys to specify a song number.
While holding down the FUNCTION button, press the SONG a button.
This will start repeat demo playback of the built-in songs in sequence, from 01 through 60. You can play along with a song on the keyboard as it is playing. The tone assigned to the keyboard is the one that is preset for the song that is playing. You can select a specific song during demo playback. For details, see step 2 under Playing Back a Specific Music Library Song.
Press the SONG a button again to stop built-in song play.
The tune selection and playback stop operations described above are the only operations that are possible during demo tune play.
Each press of the + or key raises or lowers the song number by 1. You can use the value input keys (0 to 9) to enter a specific two-digit song number. Be sure to input both digits. Example: To select song 08, enter 0 and then 8.

RECORDER

Press the SONG a button.
This starts the playback of the song.

Configuring Settings with the Keyboard
In addition to selecting tones and Music Library tunes, you also can use the FUNCTION button in combination with the keyboard keys to configure effect, keyboard touch, and other settings.
Release the FUNCTION button to complete the setting procedure.
To configure settings with the keyboard
You can configure the digital piano so no operation tone sounds in step 3. For details, see bt Operation Tone under Parameter List on pages E-21 - E-23.
Use the Parameter List on pages E-21 E-23 to find the setting you want to configure, and note its details. Use Keyboard Keys Used for Configuring Settings on page E-20 to find the location on the keyboard for configuring the setting you want. While holding down the FUNCTION button, press the keyboard key for the setting you want to configure.
The digital piano will sound an operation tone after it configures the setting. Example: To lower the transpose setting by one semitone
Keyboard Setting Operation Types
There are three types of operations that you can perform while configuring settings with the keyboard keys: Type A, Type B, and Type C. Type A: Direct input Example: Pressing the STRINGS keyboard key to select the

STRINGS 1 tone

Type B: Raising or lowering a setting using the + and or and keyboard keys Holding down a key raises or lowers the setting at high speed. To return to the initial default setting, press both keys at the same time. Type C: Value input using the numeric keys (0 to 9) Example: To enter 120, press keys 1, 2, 0.

Transpose

You can find out what operation type applies to each setting by checking the Operation Type in the Parameter List on pages E-21 - E-23.
Keyboard Keys Used for Configuring Settings
The numbers 1 through cl correspond to the same numbers in the Parameter List on pages E-21 - E-23.

[Left keyboard]

1Reverb 2Chorus 3Keyboard key (Transpose) 4Keyboard tuning (Tuning) 5Octave shift 6Temperament 7Tempo/Temperament select

[Overall]

[Center keyboard]
8Song select/Base note 9Tone selection

[Right keyboard]

clOperation lock ckBack up btOperation tone bsLocal control
bmMetronome volume blSong volume bkBrilliance bnMetronome beat
brSend channel bqLayer balance bpUSB device mode boTouch response

OFF ON OFF ON OFF ON OFF

Parameter List

Tones

Parameter Settings 1 to 4 Default: to 4 Default: 2 See page E-7. Default: GRAND PIANO (MODERN) 3 to 0 to 3 Default: to 0 to 24 Default: 0 Operation Type (page E-19) A A A Description Specifies the reverb of notes. (page E-10) Controls the breadth of notes. (page E-10) Assigns a tone to the keyboard. (page E-7) Remarks

1 Reverb 2 Chorus 9 Tone selection

bk Brilliance

(BRILLIANCE)
Specifies the brilliance of notes. (page E-8) Specifies the volume balance between the main tone and the layered tone. (page E-9)

bq Layer balance

Song/Metronome
Parameter Settings Operation Type (page E-19) B (+/) C (0 to 9) Description Specifies the tempo of Music Library songs, the metronome, recording and playback, etc. (page E-10) Remarks Always enter three digits when using the number keys (0 to 9) to input a value. Example: To input 90, enter 0, 9, 0 (leading zero required). During recording, pressing + and at the same time sets a value of 120. Always enter two-digits when using the number keys (0 to 9) to input a value. Example: To input 8, enter 0, 8 (leading zero required). This setting cannot be changed while recording. This setting cannot be changed while recording.
7 Tempo (TEMPO) 20 to 255

Default: 120

8 Song select
01 to 61 (SONG SELECT) Default: 01

B (+/) C (0 to 9)

Selects a Music Library tune. (page E-13)
bl Song volume bm Metronome
00 to 42 (SONG VOLUME) Default: to 42 volume Default: 36 (METRONOME VOLUME) (METRONOME Default: 4 BEAT)
Sets the volume level of Music Library playback. Specifies the metronome volume. (page E-11)
bn Metronome beat 0, 2, 3, 4, 5, 6
Specifies the metronome beat. (page E-10)
The metronome beat setting cannot be changed while playback of a Music Library tune is in progress.

Keyboard

Parameter Settings 12 to 0 to 12 Default: 0 B Operation Type (page E-19) Description Raises or lowers the tuning of the digital piano in semitone steps. Remarks The transpose setting cannot be configured while Music Library playback is in progress or while in the Duet Mode. Raising the key of the digital piano can cause notes the highest part of the range to become distorted. The pitch setting cannot be changed while playback of a Music Library tune is in progress.

3 Keyboard key

(Transpose)
4 Keyboard tuning 99 to 0 to 99

br Send channel

01 to 16 Default: 01

bs Local control

Off, On Default: On

bt Operation tone

ck Back up

Off, On Default: Off

cl Operation lock

Connecting to a Computer

You can connect the digital piano to a computer and exchange MIDI data between them. You can send play data from the digital piano to music software running on your computer, or you can send MIDI data from your computer to the digital piano for playback.
After starting up your computer, use a commercially available USB cable to connect it to the digital piano.
B connector USB cable (A-B type)
Minimum Computer System Requirements
The following shows the minimum computer system requirements for sending and receiving MIDI data. Check to make sure that your computer complies with these requirements before connecting the digital piano to it. Operating System Windows XP (SP2 or later)*1 Windows Vista *2 Mac OS X (10.3.9, 10.4.11 or later, 10.5.6 or later) *1: Windows XP Home Edition Windows XP Professional (32- bit) *2: Windows Vista (32- bit) USB port

A connector

Digital Piano USB port

Computer USB port

Turn on the digital piano.
If this is the first time you are connecting the digital piano to your computer, the driver software required to send and receive data will be installed on your computer automatically.
Start up your computers music software. Configure the music software settings to select one of the following as the MIDI device.
CASIO USB-MIDI : (For Windows Vista, Mac OS X) USB Audio Device: (For Windows XP) For information about how to select the MIDI device, see the user documentation that comes with the music software you are using.
Never connect to a computer that does not conform to the above requirements. Doing so can cause problems with your computer.
Connecting the Digital Piano to Your Computer
Be sure to turn on the digital piano first before starting up your computers music software.
Make sure you follow the steps of the procedure below exactly. Connecting incorrectly can make data send and receive impossible.
Turn off the digital piano and then start up your computer.
Do not start up the music software on your computer yet!
Once you are able to connect successfully, there is no problem with leaving the USB cable connected when you turn off your computer and/or digital piano. For detailed specifications and connections that apply to MIDI data send and receive by this digital piano, see the latest support information provided by the website at the following URL. http://world.casio.com/

Using MIDI

What is MIDI?
The letters MIDI stand for Musical Instrument Digital Interface, which is the name of a worldwide standard for digital signals and connectors that makes it possible to exchange musical data between musical instruments and computers (machines) produced by different manufacturers.

Change the digital pianos USB device mode to storage.
For detailed information about MIDI Implementation, visit the CASIO website at: http://world.casio.com/. See Send channel and Local control on page E-23.
While holding down the FUNCTION button, press the keyboard key that corresponds to the USB device mode. After this setting is changed, the GRAND PIANO (MODERN, CLASSIC) and ELEC PIANO button lamps flash, and all other lamps are unlit. See USB device mode (USB DEVICE MODE) on page E-23 for more information.
Transferring Song Data with a Computer
Use the procedures in this section to transfer Recorder memory data to a computer for storage, and to load songs to user song memory (Music Library 61).
On your computer, perform the required operation to display your computers storage devices.
Do this: Double-click My Computer. Double-click Computer. Skip step 3 and double-click PIANO on your Mac desktop.
Turning off the Digital Piano while it is exchanging data with a computer can cause data in Digital Piano memory to become corrupted. If this happens, a memory format operation will start the next time you turn on the Digital Piano. Note that it takes about 20 seconds for the format operation to finish, and you will not be able to perform any operation during that time.
If your computer is running this operating system: Windows XP Windows Vista Mac OS
Perform steps 1 through 3 of the procedure under Connecting the Digital Piano to Your Computer on page E-24.
The memory of this digital piano will appear as PIANO under Devices with Removable Storage.

Double-click PIANO.

PIANO contains folders named MUSICLIB and RECORDER. Use MUSICLIB to load a song into the pianos user song memory (Music Library 61), and RECORDER to transfer Recorder memory data to and from your computer.
To show file name extensions under Windows Vista
1. Open Folder Options by clicking the [Start] button, clicking [Control Panel], clicking [Appearance and Personalization], and then clicking [Folder Options]. 2. Click the [View] tab. Under [Advanced settings] clear the [Hide extensions for known file types] check box. 3. Click [OK].
To load a song into user song memory (Music Library 61)
Data Type User songs Folder Name MUSICLIB File Name and Extension* BIDSNG01.MID: SMF format data (format 0/1) BIDSNG01.CM2: CASIO original format data
1. Copy the file (.MID or.CM2) you want to load into user song memory to the MUSICLIB folder. 2. Change the name of the file to BIDSNG01, with a file name extension of.MID or.CM2. If there are two files with the names BIDSNG01.MID and BIDSNG01.CM2 in the MUSICLIB folder, only the BIDSNG01.MID data will be loaded into user song memory. If you want the BIDSNG01.CM2 file to be loaded in this case, change the name of the BIDSNG01.MID to something else.

1. Check to make sure that the USB cable is connected to the digital piano and computer, and that the correct device is selected with your computers music software. 2. Turn off the digital piano and then exit the music software on your computer. Next, turn the digital piano back on and then restart the music software on your computer. It takes about 20 seconds after you turn on power to perform the memory format operation. Wait until the format operation is complete. Note that you should take care to avoid turning off the Digital Piano while a data transfer operation with a computer is in progress.

Product Specifications

Model Keyboard Maximum Polyphony Tones PX-130BK/PX-130WE 88-key piano keyboard, with Touch Response 128 notes 16 Layer (excluding bass tones) Split (Low-range bass tones only) Brilliance (3 to 0 to 3), Reverb (4 types), Chorus (4 types), DSP, Acoustic Resonance Beats: 0, 2, 3, 4, 5, 6 Tempo Range: 20 to 255 Adjustable tone range (1 to 2 octaves) Number of Songs: 60, User Songs: 1 (memory capacity; up to 65KB )* * Based on 1 KB = 1024 bytes, 1 MB = 10242 bytes Song volume: Adjustable Part On/Off: L, R Functions: Real-time recording, playback Number of Song: 1 Number of Tracks: 2 Capacity: Approximately 5,000 notes total Recorded Data Protection: Built-in flash memory Touch Select: 3 types, Off Transpose: 2 octaves (12 to 0 to 12) Tuning: A4 = 440.0 Hz 99 cents (variable) Temperament Octave shift Operation lock
Effects Metronome Duet Music Library

Recorder

Pedals Other Functions
Damper (Soft and sostenuto pedal operations enabled by the optional SP-32 Pedal Unit.)

MIDI Inputs/Outputs

16-channel multi-timbre receive PHONES jacks: Stereo mini jacks 2 Output impedance: 3 Output Voltage: 1.5V (RMS) MAX Power: 12V DC USB port: TYPE B Damper Pedal Jack: Standard jack Pedal connector [13cm 6cm (rectangular)] 2 (Output 8W + 8W) AC Adaptor: AD-A12150LW 12V = 18W 132.2 (W) 28.6 (D) 13.5 (H) cm (52 1/1/5/16 inch) Approximately 11.2kg (24.7 lbs)
Speakers Power Requirements Power Consumption Dimensions Weight

Pedal Connector

You can connect the optionally available 3-Pedal Unit (SP-32) to the pedal connector on the bottom of the Digital Piano. You can then use the pedals for expression that is similar to that available on an acoustic piano.
Connecting Audio Equipment or an Amplifier
You can connect audio equipment or a music amplifier to the Digital Piano and then play through external speakers for more powerful volume and better sound quality.

Pedal connector

The SP-32 Pedal Unit supports half-pedal operation (pressing the pedal part way). You can adjust the amount of the effect is applied when the damper pedal is pressed part way. For details, see Half Pedal Effect (page E-43). The optionally available CS-67P special stand is required in order to use the SP-32 Pedal Unit.
The Digital Piano automatically adjusts sound output to optimize for headphone output (when headphones are connected) or built-in speaker output (when headphones are not connected). This also will cause a change in the output quality from the Digital Pianos LINE OUT R and L/MONO jacks. Whenever connecting a device to the Digital Piano, first use the VOLUME controller to set the volume to a low level. After connecting, you can adjust the volume to the level you want. Whenever you connect any device to the Digital Piano, be sure to read the user documentation that comes with the device.
Guitar amplifier Keyboard amplifier, etc.

INPUT 1

Standard plug

INPUT 2

Tape recorder, MIDI sound source, etc.

Standard jack

Audio amplifier AUX IN jack, etc. LEFT (White) RIGHT (Red)

Pin plug

Playing Output from External Equipment through the Pianos Speakers
Use commercially available cables to connect the external audio equipment to the pianos LINE IN jacks as shown in Figure. LINE IN R jack input sounds through the pianos right speaker, while LINE IN L/MONO jack input sounds through the left speaker. Connecting to the LINE IN L/MONO jack only causes the same output to be produced from both speakers. It is up to you to purchase connecting cables that are compatible with the equipment you are connecting.
Bundled and Optional Accessories
Use only accessories that are specified for use with this Digital Piano. Use of unauthorized accessories creates the risk of fire, electric shock, and personal injury.
Connecting to Audio Equipment
Use commercially available cables to connect the external audio equipment to the pianos LINE OUT jacks as shown in Figure. LINE OUT R jack output is right channel sound, while LINE OUT L/MONO jack output is left channel sound. It is up to you to purchase connecting cables like the ones shown in the illustration for connection of audio equipment. Normally in this configuration you must set the audio equipments input selector to the setting that specifies the terminal (such as AUX IN) to which the piano is connected. Use the pianos VOLUME controller to adjust the volume level.

Select the tone you want to assign to the left side (lower range) of the keyboard.
Example: To select GM SLAP BASS 1 in the VARIOUS/ GM TONES group, press the (VARIOUS/ GM TONES) button and then use the (w, q) buttons to select 073 GM SlapBass1.
Current split point key name
Press the keyboard key where you want to specify as the leftmost key of the right (upper range) tone.
This specifies the split point.
Lit Left tone number Left tone name
This exits the split point screen.
To unsplit the keyboard and return it to a single tone, press the (SPLIT) button.
The SPLIT lamp will go out, indicating that the keyboard is no longer split.
If the keyboard is set up with layered tones (page E-10) when you perform the above split operation, the layered tones will play on the right (upper range) side of the keyboard.

Using Octave Shift

After you split the keyboard (page E-11), you may find out that the lower range notes on the left are too low or that the upper range notes on the right are too high. You can use octave shift to shift the octaves of the upper range and lower range upwards or downwards in octave units.
Adjusting the Brilliance of a Tone
Press the (FUNCTION) button.
The FUNCTION lamp will light and the function screen will appear on the display.
While holding down the (FUNCTION) button, press the (TONE) button.
This displays the octave shift screen.
Use the (i) and (u) buttons to select the Tmpr/Effect screen.
Currently selected range Shift amount
Use the (PART) button to select the range whose octave you want to change.
Each press of (PART) cycles through the ranges below.
Press the (ENTER) button.
This will display a screen for selecting settings in the Tmpr/Effect group.

U1 (Upper1): Main tone

Use the (i) or (u) button to select the brilliance screen shown below.
U2 (Upper2): Layered tone
L1 (Lower1): Left (lower range) tone
Use the (w, q) buttons to shift the octave of the currently selected range.

You can import song data from an SD memory card or computer as a user song, and use it for Auto Accompaniment or for practice.
This starts playback of the song. Press the (FF) button to perform a fast forward operation or the (REW) button for rewind. Pressing and releasing either button moves one measure, while holding down a button scrolls at high speed. Pressing the (PAUSE) button pauses playback. Press again to resume song playback.
Lights with each subsequent beat of each measure Lights with the first beat of each measure
Load the song data you want to listen to one of the Digital Pianos user songs.
See Loading Data from a Memory Card (page E-47) and Connecting to a Computer (page E-51) for details about how to load data. You also could play back data directly from a memory card without loading it into Digital Piano memory. For details, see Playing Back a Song from a Memory Card (page E-48).
Press the (USER SONGS) button so its lamp is lit.

Rewind Fast forward

Press the (PLAY/STOP) button again.
This stops song playback. Song playback also will stop automatically when the end of the song is reached. To configure the Digital Piano to loop song playback without stopping, turn on Song Repeat (page E-42).

Changing the Song Tempo

You can change the song tempo using the same procedure that you use to adjust the metronome tempo. For more information, see Changing the Tempo Setting (page E-14).
Use the (w, q) buttons to select the user song you want.
Example: When user song 003 is selected
Playing on the Keyboard Using the Same Tone as the Song
User song number Song name
Hold down the (USER SONGS) button for at least two seconds.
This will assign the same tone as the right hand part of the current song to the keyboard.
You can use the procedure under Practicing Either Hands Part (Part Off) (page E-26) to turn off the left hand part and play along on the keyboard using the left hand part tone.
Adjusting the Song Volume
You can use the following procedure to adjust the volume level of the songs Auto Accompaniment, without affecting the volume of keyboard tone output. For details, see Song Volume (page E-41).
Repeating Playback of a Specific Section (Repeat)
You can configure the Digital Piano to repeat the section of a song you want to practice. You could, for example, specify repeat play from measure 5 to measure 8.

Start End

Practicing Either Hands Part (Part Off)
You can turn off the right hand part*1 or left hand part*2 of a song and play that part on the Digital Piano while the song plays back. *1 Song data Channel 4 (fixed) *2 Song data Channel 3 (fixed)
These measures are repeated.
This starts playback of the song.

Press the (PART) button.

This causes L-[ON] R-[ON] to appear on the display.

Use the (w, q) buttons to turn off the part you want.
Press (w) to toggle the left hand part or (q) to toggle the right hand part on and off.
When playback reaches the first measure of the section you want to repeat, press the (REPEAT) button.
This makes the measure the start measure. The (REPEAT) button lamp flashes at this time.
Press the (PART) button again.
This exits the part on/off screen.
This will assign the same tone as the hand that is turned off to the keyboard.
When playback reaches the last measure of the section you want to repeat, press the (REPEAT) button again.
This makes the measure the end measure. Repeat playback of the specified section starts as soon as you select the end measure. The (REPEAT) button lamp is lit (not flashing) at this time.
Press the (PLAY/STOP) button to start song playback.
The part you turned off does not sound, so you can play it on the keyboard.
Pressing (REPEAT) again returns to normal play. This will cause the (REPEAT) button lamp to go out.
Sounding a Count at the Beginning of a Song
You can configure the Digital Piano to sound a count before playback of a song starts, which helps to get the timing right when you are playing along on the keyboard. For details, see Pre-count (page E-42).

Music Presets

bmbnMUSIC PRESET csEXIT dki

4FF 3REW

Music Preset groups
Music Presets provide you with one-touch tone, rhythm, chord, and other settings that are optimized for specific musical genres and songs. In addition to built-in presets, you can create your own original Music Presets (user presets). There are a total of 300 built-in Music Presets, which are divided into three groups (A, B, C). A fourth group (D) is provided for user presets. For more information, see the Music Preset List (page A-6).
Press the (START/STOP) button to start Auto Accompaniment with the chord progression of the Music Preset. Play the melody on the keyboard.
The preset chord progression repeats until you stop it by pressing the (START/STOP) button again. Pressing the (ACCOMP ON/OFF) button so the ACCOMP ON/OFF lamp is lit (not flashing) or unlit will turn off the chord progression of the Music Preset and play the normal Auto Accompaniment pattern. Each press of the (ACCOMP ON/OFF) button cycles in the sequence shown below.

Unlit Lit Flashing

Selecting a Music Preset
Press and (MUSIC PRESET) at the same time. This causes the (ACCOMP ON/OFF) lamp to flash

and the Music Preset screen to appear.
Normal Auto Accompaniment Music Preset chord progression
You can use the following steps to change the rhythm after selecting a Music Preset. (1) Hold down the (RHYTHM) button until the displayed Music Preset number and name change to the rhythm number and name. (2) Use the (w, q) buttons to select the rhythm you want. (3) Hold down the (RHYTHM) button again until the rhythm number and name change back to the Music Preset number and name. To change the tone, use the through (tone group) buttons to select the tone group and then use the (w, q) buttons to select a tone number.

Music Preset number

Music Preset name
Use buttons to (Music Preset group buttons) to select a group, and then use the (w, q) buttons to select the Music Preset you want.
This will configure the Digital Piano with settings (tone, rhythm, etc.) of the selected Music Preset. The following are the settings that are included in a Music Preset. Tones (main, layer, lower split) (page E-9) Layer balance (page E-10) Octave shift (page E-12) Reverb (page E-13) Chorus (page E-13) Rhythm (page E-21) Tempo (page E-20) Auto Harmonize (page E-20)
To exit a Music Preset, press and (MUSIC PRESET) at the same time.

6START/STOP

btw/NO, q/YES ctu
Creating an Original User Preset
A Music Preset editor is provided to allow you to create your own original Music Presets (user presets). Up to 50 user presets can be stored in Music Preset Group D.
Edit the Music Preset parameters.
4-1. To edit the chord progression Press the (w) down button to display CHORD and then press the (ENTER) button to advance to the chord progression editing screen. Next, perform the editing operation described under To edit the chord progression (page E-29). After you finish the editing operation, press the (EXIT) button to return to the screen for selecting the type of editing operation, above. 4-2. To edit Auto Accompaniment parameters Press the (q) up button to display Parameter and then press the (ENTER) button to advance to the Auto Accompaniment parameter editing screen. Next, perform the editing operation described under To edit Auto Accompaniment parameters (page E-31). After you finish the editing operation, press the (EXIT) button to return to the screen for selecting the type of editing operation, above.
Select the Music Preset you want to edit in order to create your user preset. Change the tone number, rhythm number, and other settings of the Music Preset as you want.
The settings you configure here will be saved as a user Music Preset. See step 2 under Selecting a Music Preset (page E-27) for the settings you can configure and save for a user Music Preset.
Press the (BALLAD/PIANO RHYTHMS) and (USER RHYTHMS) buttons at the same time.
This displays a screen for selecting the type of editing operation you want to perform.

You can record your music as you play and store up to five songs in Digital Piano memory for later playback. You can divide a song into parts (by instrument, by left hand and right hand, etc.) and record each part separately. You can even use punch-in recording to edit specific parts of existing recordings.
When you are finished, press the (START/ STOP) button. This will cause the (RECORDER) lamp to flash and
then light, indicating the playback mode. If you are using Auto Accompaniment, you also can end the recording session by pressing the (ENDING) button.

Lit: Playback mode

Recording or Playing Back a Single Song
The following are the steps for recording or playing back a single recorder memory song.
Press the (RECORDER) button twice so its lamp is flashing.
This turns on the recorder and enters record mode. Each press of the (RECORDER) button cycles through modes as shown below.
Recorder Off Unlit Lit: Playback mode Recorder On Flashing: Record mode
To play back what you have recorded, press (START/STOP) again. Each press of starts and stops playback. To turn off the recorder, press the (RECORDER) button so its lamp goes out.

Unlit: Recorder off

Configure the tone, rhythm, and other settings you want to use.
The settings you configure here will be included as part of the recorded song data. For details about what is included in the recorded song data, see System Track (page E-35).
Play something on the keyboard.
Recording starts as soon as you play something. If Auto Accompaniment is playing, it will be included in the recorded data.
Recorder memory capacity is approximately 10,000 notes per song. When remaining capacity is 100 notes or less, the (RECORDER) button lamp will flash at high speed. Recording will stop automatically when memory becomes full. Repeat, fast reverse, fast forward, pause, and tempo adjustment during playback are the same as when playing back user songs. See Listening to Songs Loaded from an External Source (page E-25) for more information. You can listen to the song data currently stored in recorder memory at any time by pressing the (RECORDER) button to enter the playback mode and then pressing (START/STOP).
A new recording replaces (deletes) previously recorded contents. If power to the Digital Piano is cut off while recording is in progress, everything you recorded up to that point will be deleted. Take care so power is not turned off accidentally during recording operations.
Recording to a Specific Track (Part)
You can record specific instruments, the left hand and right hand, or other parts of a song individually, and then combine them into a final song.

What is a track?

Recording or Playing Back Multiple Songs
You can record up to five songs (numbered 1 through 5) in memory. After that, you can select a specific song for playback.
A track is a separate recorded part of a song. The recorder of this Digital Piano supports a total of 17 tracks, which are divided between two types described below. System Track In addition to notes you play on the keyboard and other performance operation data, the system track also includes a wide range of setup information for the song, including layer on/off, split on/off, tempo, Auto Accompaniment settings, reverb on/off, etc. When you record a single-track song to recorder memory, as shown under Recording or Playing Back a Single Song (page E-34) and Recording or Playing Back Multiple Songs (page E-35), everything is recorded to the system track. Tracks 01 through 16 These tracks can be used to record notes, as well as pitch bend wheel and pedal operations, and the keyboard tone setting. These tracks can be combined with the system track and each other to create the final song.
Use the (RECORDER) button to cycle through the recorder modes until the playback mode is selected.
While holding down the (FUNCTION) button, press the (RECORDER) button.
This displays the song selection screen.
Use the (w, q) buttons to select the song number you want. Press the (EXIT) button to exit the song selection screen. To record to the currently selected song, press the (RECORDER) button. To play back the currently selected song, press the (START/STOP) button. If you are recording, continue from step 2 under Recording or Playing Back a Single Song (page E-34).

Supported Track Data

The following describes the data that can be recorded to each type of track. System Track, Tracks 01 through 16 Keyboard notes, keyboard tone setting (main), pedal and pitch bend wheel operation System Track only Layer, split, octave shift, reverb, chorus, keyboard temperament, tempo, Auto Accompaniment play, auto harmonize, one-touch preset, Music Preset,*1 registration*1*2 *1 Recall only *2 The Auto Accompaniment volume level and transpose setting of the recalled data is not included in the recording.
Select the tone of the part you want to record to the track. Press the (START/STOP) button.
This will start playback of what you recorded to the system track and start recording to the currently selected track. Play what you want to record to the current track along with the playback from the system track.
To stop recording, press the (START/ STOP) button again. This enters the playback mode. Press the (START/
STOP) button again to play back the track you just recorded. Each press of (START/STOP) starts and stops playback. You can use the following procedure to turn specific tracks on (play enabled) and off (play disabled). This allows you to listen only to the track(s) you want when recording a new track. (1) While holding down the (FUNCTION) button, press the (RECORDER) button. This displays the song selection screen. (2) Press the (i) button once. This displays the track on/off screen. (3) Use the (w, q) buttons to select the track you want, and then press the (ENTER) button to toggle it on or off.

Use the (w, q) buttons to select the track you want to delete. Hold down the (RECORDER) button until the message Sure? appears on the display. Press the (YES) button to delete the track. To cancel the delete operation, press the (NO)
Re-recording Part of a Recorder Song (Punch-in Recording)
To stop punch-in recording, press the (START/STOP) button again.
Anything in the track following the point where you pressed the (START/STOP) button will be retained as-is. If you want to delete all of the data in the track following the section you re-recorded with punch-in recording, press the (RECORDER) button in place of the (START/STOP) button above. If you want to cancel punch-in recording and retain the original (unedited) track data, hold down the (RECORDER) button until the display exits the punch-in recording screen.
Press the (START/STOP) button to start playback.
Punch in recording will start from the start measure and stop with the end measure automatically.
Play the notes and perform the other operations you want.
Specifying the Punch-in Recording Location (Auto Punch-in Recording)
You can use the following procedure to specify a particular range for punch-in recording.
Start measure End measure

Punch-in recording range

Turn on the recorder, enter the record mode, and display the recording setup screen. While holding down the (FUNCTION) button, press the (RECORDER) button. Use the (u) and (i) buttons to display AutoPu.IN, and then use the (w, q) buttons to select the start measure. Use the (u) and (i) buttons to display AutoPu.OUT, and then use the (w, q) buttons to select the end measure.
After selecting the start and end measures, press the (EXIT) button to exit the recording setup screen.
Select the track that contains the range of measures you want to re-record.
Hold down the (RECORDER) button until the punch-in recording screen appears on the display. Press the (q) button to turn on auto punch-in recording.
Performing Punch-in Recording for Areas Smaller than One Measure
Example: To re-record from beat 3 of measure 2 up to beat 1 of measure 4
To re-record this section

1. 2. 3. 4. 5.

Start playback of the song that contains the section you want to re-record. When playback reaches the beginning of the section you want to re-record, press the (REPEAT) button. When playback reaches the end of the section you want to re-record, press the (REPEAT) button again. Press the (START/STOP) button to stop playback. Turn on the recorder and select the track that contains the section you want to re-record.

For information about selecting a track, see step 3 under Recording to a Specific Track (Part) (page E-35).

6. 7. 8. 9.

Hold down the (RECORDER) button until the punch-in recording screen appears on the display. Press the (q) button to turn on auto punch-in recording. Press the (REPEAT) button to turn on repeat. Press the (START/STOP) button.
This starts punch-in playback from the measure before the location (start point) you specified in step 2, above. Punch-in recording starts automatically when playback reaches the start point and ends automatically when it reaches the location you specified in step 3 (end point).
Use the procedure below to specify a punch-in recording area that includes a part of a measure.

Other Settings

btw, q bsFUNCTION dki ctu
You can use the settings in this section to adjust the tuning and touch of the keyboard, to configure pedal and MIDI settings, and to configure other parameters in order to tailor Digital Piano operation to your particular needs.

Configuring Settings

The FUNCTION lamp will light and the function screen will appear on the display. (See table below.)
Holding down the (FUNCTION) button while you press the (w, q) buttons in step 3 will scroll the setting in steps of 10. You also can use the (FUNCTION) button for faster scrolling while changing the tone number, rhythm number, and other scrollable settings. Keep the (FUNCTION) button depressed while pressing a (w, q) button for highspeed scrolling. Releasing the (FUNCTION) button first can result in another unintended setting being changed.

Parameter or group

Use the (u) and (i) buttons to select one of the parameters (1 through 8) shown in the table below.
Parameters 4 through 8 actually are parameter groups. After selecting a group, press the (ENTER) button, and then use buttons (u) and (i) to select the parameter you want. Short cut buttons also are available for accessing a parameter directly after you press the (FUNCTION) button, without going through the menu. See the Shortcut Button column in the table below for the applicable shortcut button of each parameter.
Use the (w, q) buttons to change the setting of the currently selected parameter. To return to the function screen, press the (EXIT) or (FUNCTION) button.

Data Type User rhythms User Music Preset Recorder songs Registrations
File Name (** = file number) USRRHY** USRMPS** RECSNG** REGIST**
To select this type of data:*1 User rhythms User Music Preset
The message Please Wait will remain on the display while the save operation is being performed. Do not perform any Digital Piano operation while this message is on the display. Complete appears on the display after data save is complete. If there already is a file with the same name on the memory card, a message (Replace?) will appear asking if you want to replace it with the new data. Press the (YES) button to overwrite or the (NO) button to cancel the save operation.
Recorder songs Select from among recorder songs 1 through 5 (page E-34). Registrations*2 Press the (REGISTRATION) button so its lower lamp is lit.
*1 For more information about data types, see page E-44. *2 All registration data (8 banks 12 areas) is saved in a single file.

Memory Card Data Storage

The above procedure stores Digital Piano data in a folder named MUSICDAT on the memory card. The MUSICDAT folder is created automatically when you format the memory card on the Digital Piano (page E-45). Note that files not in the MUSICDAT folder cannot be loaded, deleted, or renamed by this Digital Piano. You also will not be able to load or delete any file stored in any subfolder inside the MUSICDAT folder.
Hold down the (CARD/INTERNAL) button until the LOAD screen appears for the data you selected.
You can cancel the LOAD/SAVE operation any time by pressing the (EXIT) button.
Press the (i) button to switch to the SAVE screen for the data you selected.
If you are saving a recorder song to a standard MIDI file (SMF), press the (i) button again so SMF is displayed on the right side of the screen.
Loading Data from a Memory Card
You can use the procedure below to load data from a memory card into Digital Piano memory.
Deleting Memory Card Data
Use the following procedure to delete memory card data (files).
Insert the memory card into the Digital Pianos memory card slot. While holding down the (FUNCTION) button, press the (CARD/INTERNAL) button.
This displays the memory card format screen (page E-45).
Make sure that all of the data you want to load is in the MUSICDAT folder on the memory card. Note that if you put data into a music data play-only folder on a memory card (such as the MUSIC__B folder), you will no longer be able to load that file into Digital Piano memory.
Insert the memory card into the Digital Pianos memory card slot. Select the data you want to load.
Do this: Select from among user rhythms 001 through 010 (page E-21). Select from among user songs 001 through 010 (page E-25). Select from among user Music Presets 001 through 050 (page E-28).

This is an unavoidable result of the digital sampling process,* and does not indicate malfunction. * Multiple digital samples are taken for the low range, middle range, and high range of the original musical instrument. Because of this, there may be a very slight difference in tonal quality and volume between sample ranges.
Performing a button operation while playing with the Duet Mode, Auto Accompaniment, the recorder, or When I press a button, the note other functions can cause such phenomena when the Digital Piano switches internal tone effects. It does that is sounding cuts out not indicate malfunction. momentarily or there is a slight change in how effects are applied. Even though I play on different ranges of the keyboard, the notes do not change octaves. The ranges of certain tones are limited, which means that octaves change normally up to a certain low note or high note. With such a tone, the notes of the lowest octave will be repeated to the left of the lowest possible note, and the highest octave will be repeated to the right of the highest possible note. This is due do limitations in the range of the original musical instrument for each tone, and does not indicate malfunction of the Digital Piano.

Product Specifications

Keyboard Maximum Polyphony Tones Effects Metronome Duet Auto Accompaniment 88-key piano keyboard, with Touch Response (3 types) 128 notes 250 (with Layer and Split) Reverb (4 types), Chorus (4 types), Brilliance (3 to 0 to 3), Acoustic Resonance Beats per measure: 0, 2, 3, 4, 5, 6 Tempo Range: 20 to 255 Adjustable tone range: 0 to 3 octaves for the left keyboard; 4 to 1 octaves for the right keyboard Built-in Rhythms: 180 User Rhythms: Up to 10 (Approximately 40KB* maximum per rhythm) One Touch Presets: 180 types Auto Harmonize: 12 types
Demo Songs User Songs Music Presets Registration Recorder
8 songs (tone demo songs) Up to 10 songs (320KB* maximum per song) Built-in Presets: 300 User Presets: Up to 50 (Approximately 8KB* maximum per preset) (4 rhythm areas + 8 tone areas) 8 banks Functions: Real-time recording, playback Number of Songs: 5 Number of Tracks: 17 (System Track + Tracks 01 through 16) Capacity: Approximately 50,000 notes total (Up to approximately 10,000 notes per song) Punch-in recording

Pedals Other Functions

Damper, Soft/Sostenuto (switchable) Transpose: 1 octave (12 to 00 to 12) Tuning: A4 = 440.0 Hz 99 cents Octave Shift: 2 octaves Temperaments: 17 types Stretch Tune Panel Lock

Group Name/ Nombre del grupo POPS/JAZZ POPS 8 BEAT/16 BEAT 021 DANCE ROCK JAZZ EUROPEAN 058 POP 1 POP 2 FAST POP FUNK POP POP ROCK 6/8 POP FAST SOUL SLOW SOUL 60S SOUL POP SHUFFLE STRAIGHT 8 BEAT 1 STRAIGHT 8 BEAT 2 FUNK 8 BEAT MELLOW 8 BEAT GUITAR 8 BEAT 8 BEAT 8 BEAT POP OLDIES 8 BEAT 60S 8 BEAT 16 BEAT 16 BEAT SHUFFLE HIP-HOP DANCE POP DISCO POP TECHNO POP TRANCE MODERN R&B MODERN DANCE DISCO SOUL STRAIGHT ROCK SHUFFLE ROCK BLUES 1 BLUES 2 EP BLUES SLOW BLUES SOFT ROCK LATIN ROCK SLOW ROCK 50S ROCK 50S PIANO ROCK NEW ORLNS R&R 60S ROCK ROCK 70S PIANO ROCK ROCK WALTZ SLOW BIG BAND MIDDLE BIG BAND FAST BIG BAND SWING 1 SWING 2 SLOW SWING JAZZ WALTZ FOX TROT QUICKSTEP JAZZ COMBO 1 SCHLAGER POLKA WALTZ 1 Group Number/ Nmero de grupo Sequential Number/ Nmero secuencial Rhythm name/ Nombre del ritmo Group Number/ Nmero de grupo LATIN/WORLD LATIN I 015 LATIN II 026 COUNTRY Group Name/ Nombre del grupo 031 Sequential Number/ Nmero secuencial Rhythm name/ Nombre del ritmo WALTZ 2 SLOW WALTZ VIENNESE WALTZ FRENCH WALTZ SERENADE TANGO MARCH 1 MARCH 2
BOSSA NOVA SLOW BOSSA NOVA BEGUINE SAMBA 1 SAMBA 2 MAMBO RHUMBA CHA-CHA-CHA MERENGUE BOLERO SALSA 1 SALSA 2 REGGAE POP REGGAE SKA REGGAETON 1 REGGAETON 2 CUMBIA CALYPSO FORRO PAGODE BANDA PASILLO ARGENTINE CUMBIA PUNTA BACHATA MODERN COUNTRY COUNTRY 8 BEAT COUNTRY BALLAD COUNTRY SHUFFLE FINGER PICKING COUNTRY COUNTRY WALTZ BLUEGRASS
WORLD I AMERICAN DIXIE TEX-MEX FAST GOSPEL SLOW GOSPEL HAWAIIAN SPANISH/EASTERN EUROPEAN PASODOBLE CAUCASIAN RUSSIAN CHANSON 108 RUSSIAN CHANSON 109 POLISH WALTZ ARABIC/ORIENTAL SIRTAKI MUS ADANI BALADI KHALIJI MALFOOF
Group Sequential Number/ Number/ Nmero de Nmero grupo secuencial WORLD II INDIAN CHINESE SOUTHEAST ASIAN JAPANESE BALLAD/PIANO RHYTHMS BALLAD VARIOUS PIANO RHYTHMS Group Name/ Nombre del grupo
Rhythm name/ Nombre del ritmo
BHANGRA DADRA GARBA KEHARWA DANDIYA TEEN TAAL BHAJAN GUANGDONG JIANGNAN BEIJING DONGBEIYANGGE JINGJU HUANGMEIXI QINQIANG YUJU YAOZU DAIZU MIAOZU MENGGU XINJIANG ZANGZU KRONCONG DANGDUT ENKA
Group Number/ Nmero de grupo 041
Sequential Number/ Nmero secuencial 180
Rhythm name/ Nombre del ritmo PIANO MARCH 2 STRIDE PIANO WALTZ 3 WALTZ 4 WALTZ 5
Sequential number rhythms 171 through 180 do not sound unless a chord is being played.
Los ritmos secuenciales nmeros 171 al 180 no suenan a menos que se ejecute un acorde.
PIANO ROCK BALLAD 90S BALLAD MODERN BALLAD ELECTRIC BALLAD SLOW BALLAD 1 SLOW BALLAD 2 R&B BALLAD 16 BEAT BALLAD SOUL BALLAD POP BALLAD 1 POP BALLAD 2 PIANO WALTZ BALLAD 90S 6/8 BALLAD 6/8 BALLAD 1 6/8 BALLAD 2 ROCK BALLAD CHRISTMAS SONG CHRISTMAS WALTZ SCREEN SWING SYMPHONY STR QUARTET PIANO 8 BEAT PIANO BALLAD 1 PIANO BALLAD 2 EP BALLAD 1 EP BALLAD 2 BLUES BALLAD JAZZ COMBO 2 JAZZ COMBO 3 RAGTIME BOOGIE-WOOGIE PIANO ROCK & ROLL ARPEGGIO 1 ARPEGGIO 2 ARPEGGIO 3 PIANO MARCH 1

C BALLAD Love Ballad R&B Ballad Soul Ballad Blues Ballad MovieBallad1 MovieBallad2
Fingering Guide/ Gua de digitacin
Fingered 1, Fingered 2 Chords/ Acordes Fingered 1, Fingered 2
C Cm Cdim Caug *3 Csus4 *3 Csus2 *3 C7 Cm7 *3 CM7 Cm7b5 *3 C7b5 *3 C7sus4 Cadd9 Cmadd9 CmM7 Cdim7 *3 C69 *3 C6 *1 *3 Cm6 *2 *3
*1 With Fingered 2, interpreted as Am7. *2 With Fingered 2, interpreted as Am7b5. *3 Inverted form not supported in some cases. *1 Con Fingered 2, se interpreta como Am7. *2 Con Fingered 2, se interpreta como Am7b5. *3 En algunos casos no se puede usar de forma invertida.
Fingered 3, Full Range Chords/ Acordes Fingered 3, Full Range
In addition to the chords that can be fingered with Fingered 1 and Fingered 2, the following chords also are recognized. Adems de los acordes que se pueden digitar con Fingered 1 y Fingered 2, tambin se pueden reconocer los siguientes acordes.
Fm C bm Ddim A b7 F7 Fm7 Gm7 A badd9 Gm Am B C C C C C C C C C C# C D C E C F C G C Ab C Bb C B C C #m Dm C C
With Fingered 3, the lowest note fingered is interpreted as the base note. Inverted forms are not supported. With Full Range Chord, when the lowest fingered is a certain distance from the neighboring note, the chord is interpreted as a fraction chord. Unlike Fingered 1, 2, and 3, Full Range Chord requires pressing of at least three keys to form a chord.
Con Fingered 3, la nota ms baja digitada se interpreta como nota base. No se pueden usar formas invertidas. Con Full Range Chord, cuando la nota digitada ms baja se encuentre a cierta distancia de la nota adyacente, el acorde se interpreta como un acorde bitonal. A diferencia de Fingered 1, 2, y 3, Full Range Chord requiere la pulsacin de tres teclas como mnimo para formar un acorde.
(D#)/Eb E F G A B F#/(Gb) (G#)/Ab (A#)/Bb

Chord Type

C#/(Db)
Chord Example List/Lista de ejemplos de acordes
Since the chord input range is limited, this model may not support some of the chords shown above.
Debido a que el rango de entrada de acordes es limitado, es posible que este modelo no admita algunos de los acordes mostrados arriba.

Model PX-330

Transmitted Recognized

Version : 1.0

Function

Remarks

Basic Channel
Default Changed Default Messages Altered

1 - - 16 Mode 3 X

Note Number
0 - 127 True voice Note ON Note OFF Keys Chs O 9nH v = 1 - 127 X 8nH v = 64 X X O
0,5 6, 100, 121 O X X O O X X X X X X O X O O X X X X X X X X O O O O O
0 - - 127*1 O 9nH v = 1 - 127 X 9nH v = 0, 8nH v =** X O O
O O O O O O O O O O O O O O O O O O O O O O O O O O O O Bank select Modulation Portamento Time Data entry LSB, MSB*2 Volume Pan Expression DSP Parameter0*2 DSP Parameter1*2 DSP Parameter2*2 DSP Parameter3*2 Damper Portamento Switch Sostenuto Soft pedal Vibrato rate Vibrato depth Vibrato delay DSP Parameter4*2 DSP Parameter5*2 DSP Parameter6*2 DSP Parameter7*2 Portamento Control Reverb send Chorus send RPN LSB, MSB*2 All sound off Reset all controller