Notes for Users in Australia and New Zealand
Modem warning notice for Australia
Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been specifically configured to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in your modem being operated in a noncompliant manner. To verify that the country/region is correctly set, enter the command ATI which displays the currently active setting. To set the country/region permanently to Australia, enter the following command sequence: AT%TE=1 ATS133=1 AT&F AT&W AT%TE=0 ATZ Failure to set the modem to the Australia country/region setting as shown above will result in the modem being operated in a non-compliant manner. Consequently, there would be no permit in force for this equipment and the Telecoms Act 1991 prescribes a penalty of $12,000 for the connection of non-permitted equipment.
Notes for use of this device in New Zealand
The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom. In addition to satisfactory line conditions a modem can only work properly if: a/ it is compatible with the modem at the other end of the call and b/ the application using the modem is compatible with the application at the other end of the call - e.g., accessing the Internet requires suitable software in addition to a modem. This equipment shall not be used in any manner which could constitute a nuisance to other Telecom customers.
Some parameters required for compliance with Telecom's PTC Specifications are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set to operate within the following limits for compliance with Telecom Specifications: a/ There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation, and b/ The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next. c/ Automatic calls to different numbers shall be not less than 5 seconds apart. Immediately disconnect this equipment should it become physically damaged, and arrange for its disposal or repair. The correct settings for use with this modem in New Zealand are as follows: ATB0 (CCITT operation) AT&G2 (1800 Hz guard tone) AT&P1 (Decadic dialling make-break ratio =33%/67% ATS0=0 (not auto answer) ATS10=less than 150 (loss of carrier to hangup delay, factory default of 15 recommended) ATS11=90 (DTMF dealing on/off duration=90 ms) ATX2 (Dial tone detect, but not (U.S.A.) call progress detect) When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: (a) a person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network. (b) caller identification information (which occurs between the first and second ring cadences) is not destroyed. The preferred method of dialling is to use DTMF tones (ATDT.) as this is faster and more reliable than pulse (decadic) dialling. If for some reason you must use decadic dealing, your communications program must be set up to record numbers using the following translation table as this modem does not implement the New Zealand "Reverse Dialling" standard. Number to be dialled: Number to program into computer: Note that where DTMF dealing is used, the numbers should be entered normally. The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired.

Caps Lock

Optical Disc drive
The computer will either have a CD-RW/DVD-ROM drive, or a single layer or dual layer DVD Super Multi drive supporting R Double Layer depending on its configuration. An ATAPI interface controller is used for the operation of these optical drives. When the computer is accessing a disc, an indicator on the drive glows.
Region codes for DVD drives and media
The disc drive and its media are manufactured according to the specifications of six marketing regions. When you purchase DVD-Video, make sure it matches your drive, otherwise it will not play properly. Code Region Canada, United States Japan, Europe, South Africa, Middle East Southeast Asia, East Asia Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean Russia, Indian Subcontinent, Africa, North Korea, Mongolia China

Writable discs

This section describes the types of writable discs. Check the specifications for your drive to for the type of discs it can write. Use TOSHIBA Disc Creator to write compact discs. Refer to Chapter 4, Operating Basics.
CD-R discs can be written only once. The recorded data cannot be erased or changed. CD-RW discs can be recorded more than once. Use either 1x, 2x, or 4x multi-speed CD-RW discs or high-speed 4x to 10x discs. The write speed of ultra-speed CD-RW discs is a maximum of 24x speed.
DVD-R and DVD+R discs can be written only once. The recorded data cannot be erased or changed. DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once.
The full-size CD-RW/DVD-ROM drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") discs without using an adapter. The read speed is slower at the centre of a disc and faster at the other edge. DVD read 8 speed (maximum) CD read 24 speed (maximum) CD-R write 24 speed (maximum) CD-RW write 24 speed (maximum, ultra-speed media)
The full-size DVD Super Multi drive supporting R Double Layer module lets you record data to rewritable discs as well as run either 12cm (4.72") or 8cm (3.15") discs without using an adapter.
The read speed is slower at the centre of a disc and faster at the other edge. DVD read 8 speed (maximum) DVD-R write 8 speed (maximum) DVD-RW write 6 speed (maximum) DVD+R write 8 speed (maximum) DVD+RW write 8 speed (maximum) DVD-RAM write 5 speed (maximum) CD read 24 speed (maximum) CD-R write 24 speed (maximum) CD-RW write 16 speed (maximum, ultra-speed media) DVD+R (DL) write 4 speed (maximum) DVD-R(DL) write 4 speed (maximum) This drive cannot use discs that allow writing faster than 8x speed or faster (DVD-R and DVD+R with Single Layer), 6x speed or faster (DVD-RW), 8x speed or faster (DVD+RW), 5x speed (DVD-RAM) or ultra-speed or faster (CD-RW).
The AC adapter converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any country/region. To recharge the battery, simply connect the AC adapter to a power source and the computer. See Chapter 6, Power and Power-Up Modes, for details.

Align the finger and sensor like the drawings.
Points to note about the FingerPrint Sensor
Please be aware of the following considerations when using the FingerPrint sensor. A failure to follow these guidelines might result in damage to the sensor, sensor failure, FingerPrint recognition problems or a lower FingerPrint recognition success rate. Do not scratch or poke the sensor with your nails or any hard or sharp objects. Do not press the sensor strongly. Do not touch the sensor with a wet finger or any wet objects - keep sensor surface dry and free of water vapor. Do not touch the sensor with a soiled or dirty finger as minute foreign particles of dust and dirt may scratch it. Do not paste stickers or write on the sensor. Do not touch the sensor with a finger or any other object which may have a built-up of up static electricity on it. Observe the following before you place your finger on the sensor whether for FingerPrint enrollment/registration or recognition. Wash and dry your hands thoroughly. Remove static electricity from your fingers by touching any metal surface. Static electricity is a common cause of sensor failures, especially when the weather is dry. Clean the sensor with a lint-free cloth - do not use detergent to any other chemicals to clean the sensor. Avoid the following finger conditions for enrollment or recognition as they may result in FingerPrint enrollment errors or a drop in the FingerPrint recognition success rate. Soaked or swollen finger (e.g. after taking bath) Injured finger Wet finger Soiled or oily finger Extremely dry skin condition on finger
Observe the following to improve the FingerPrint recognition success rate. Enroll two or more fingers. Enroll additional fingers if recognition failure occurs when using already enrolled fingers. Check the condition of your finger - any conditions which have changed since enrollment, such as injured, rough, extremely dry, wet, soiled, dirty, oily, soaked, swollen fingers, may lower the recognition success rate. Also if the FingerPrint is worn down or the finger becomes thinner or fatter, the recognition success rate may be lowered. As the FingerPrint for each finger is different and unique. you should ensure that only the registered or enrolled FingerPrint or FingerPrints are used for identification. Check the position and speed at which you swipe your finger across the sensor - please refer to the preceding drawing. How to Delete the FingerPrint Data Saved FingerPrint Data is stored in special non-volatile memory inside the FingerPrint sensor. Therefore, if you give the computer to someone else, or dispose of it in any way, the following process is recommended to delete your FingerPrint information: 1. Click Start followed by All Programs, followed by Protector Suite QL and then click Control Center. 2. The Protector Suite QL screen is displayed. 3. Click FingerPrint and click Delete. 4. Click Settings and click FingerPrint Storage Inspector. 5. The FingerPrint Storage Inspector screen will be displayed. If FingerPrint data is displayed as part of the list, simply select all of this information and then Remove. 6. Check whether all of the FingerPrint data was deleted on the FingerPrint Storage Inspector screen. In use, please be aware of the following limitations of the FingerPrint sensor: The FingerPrint sensor compares and analyzes the unique characteristics in a FingerPrint. A warning message will be displayed when recognition is abnormal or recognition is not successful within a fixed duration. The recognition success rate may differ from user to user. Toshiba does not guarantee that this FingerPrint recognition technology will be error-free. Toshiba does not guarantee that the FingerPrint sensor will recognize the enrolled user or accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of this FingerPrint recognition software or utility.

Points to note about the FingerPrint Utility software
You are able to backup saved FingerPrint data and information within the PasswordBank by using the import or Export User Data facility under the FingerPrint management software. However, please be aware that any encrypted files cannot be backup within FileSafe using this function - in these instances it is recommended that you backup these files to external media using standard file copy processes. The user should back up the user profile information when using the functions provided in this software to encrypt files or folders. If this software or the user information is deleted without backing up the user profile information, the encrypted files will no longer be accessible. In addition, if the backup data is not used, the user will not be identified as the same user even if the same name is used again in user enrolment. Please refer to the following procedures to back up. If Windows Vistas file encryption function EFS (Encryption File System) is used to encrypt a file, the file cannot be further encrypted using the encryption function of this software. In the help file, it is stated that this software's Password Bank function can be used for the Internet and general applications. However, the Internet Password Bank function in the FingerPrint utility provided in this computer can only be used with IE (Internet Explorer).

Set up Procedure

Please use the following procedure when first using FingerPrint authentication.

FingerPrint Registration

You should initially enroll the required authentication data using the User Enrollment Wizard. In use, the FingerPrint authentication system will use the same username and password as defined within Windows operating system. If no Windows password has been configured, you must do this before starting the FingerPrint registration process. Up to twenty-one FingerPrint patterns can be registered on this sensor. 1. Click Start followed by All Programs followed by Protector Suite QL and then click User Enrollment. You are also able to start the User Enrollment Wizard by using the following method. Click the Protector Suite QL icon in the Task Bar. Swipe your finger across the FingerPrint Sensor. 2. Click Next.
3. At the Users Password screen which is then displayed, you should ensure that the same Windows username is displayed before entering the appropriate password into the Enter you password field. Once this has been done, click Next. 4. At the Hints for FingerPrint Enrollment screen, confirm the message displayed and ensure that there is a check mark in the Run Interactive Tutorial box. Once this has been done, click Next. 5. At the Correct swipe Procedure screen, confirm the message that is diplayed and then click Next. 6. At the Scanning Practice screen, you are able to practice swiping your finger to ensure you use the correct method. Once you have finished practicing, click Next. 7. At the Users Fingers screen, select the finger you wish to enroll from the illustration and then click Next. On this screen please be aware that any previously enrolled FingerPrints would have green check marks, while the FingerPrint you are about to enroll will have a red check mark. If any of the previously enrolled FingerPrints is selected again, the latest information will be enrolled and any previous information over-written. 8. At Advanced Security screen, select whether you wish tto enable the security function, and then click Next. 9. At Finalization screen, click Finish - this will complete the FingerPrint registration process.

CAPTURE STILL IMAGES VIDEO RECORDING AUDIO RECORDING FUNCTION
Capture Still Images Video Recording Audio Recording Function About Player Effects Properties
Click to see a preview of the captured image; you can also e-mail the image. Click to start recording, click again to stop recording and see a preview of the video. Click to start recording, click again to stop and listen to a preview of the audio. Access additional functions: About, Player, Effects, Properties, Settings and Help. Displays software manufacturer details. Play video files. Choose images to be displayed on the capture screen. Choose from the Options tab to flip, zoom, flicker rate, night mode and backlight compensation; in the Image tab change the colour settings; in the profile tab change the lighting conditions.

Settings

Choose from the: Options tab to change the tool position; the Picture tab to select picture output options such as size, export file and saving location; the Video tab to choose output settings such as Frame Rate, Size, Compression and the file save path; the Audio tab to chnage the Audio Device, Compression, Volume and file save path. Displays the help files for the software.

Using the internal modem

This section describes how to setup the modem and use it to connect to other computer systems. Refer to the computer's online help files and the online help files for your modem software, for more information. The internal modem does not support the voice functions described in the help files. All data and fax functions are supported. In case of a lightning storm, unplug the modem cable from the telephone jack. Do not connect the modem to a digital telephone line. A digital line will damage the modem.
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 3. Do not use the telephone to report a gas leak in the vicinity of the leak. 4. Use only the power cord indicated in this manual.

Please observe the following points when you write or rewrite data. Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM media. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYOYUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD Specifications for Recordable Disc for General Version 2.0 TAIYOYUDEN CO., LTD. Matsushita Electric Industrial Co., Ltd. DVD Specifications for Re-recordable Disc for Version 1.1 or Version 1.2 VICTOR COMPANY OF JAPAN, LIMITED MITSUBISHI CHEMICAL CORPORATION MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Matsushita Electric Industrial Co., Ltd. Hitachi Maxell Ltd. *DVD Multi drive and DVD Super Multi can use DVDRAM. MITSUBISHI CHEMICAL CORPORATION MITSUBISHI CHEMICAL COPRORATION FUJIFILM Corporation FUJIFILM Corporation

CD-RW: DVD-R:

DVD-RW:

DVD+R: DVD+RW: *DVD-RAM

DVD+R (Double Layer) DVD-R (Dual Layer) DVD-R Label Flash DVD+R Label Flash
If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur. Be careful to check the disc for dirt or damage before you use it. The actual number of rewrites to CD-RW or DVD-RW/+RW/-RAM is affected by the quality of the disc and the way it is used. There are two types of DVD-R: authoring and general use discs. Do not use authoring discs. Only general use discs can be written to by a computer drive. We can support only Format 1 of DVD-R DL. Therefore you can not do the additional writing. If your data is under DVD-R (SL) capacity, we suggest to use DVD-R (SL) media. You can use DVD-RAM discs that can be removed from a cartridge and DVD-RAM discs designed without a cartridge. You cannot use a disc with a 2.6 GB single-sided capacity or 5.2 GB double-sided capacity. Other DVD-ROM drives for computers or other DVD players may not be able to read DVD-R/+R/-RW/+RW/-RAM discs. Data written to a CD-R/DVD-R/+R disc cannot be deleted either in whole or in part. Data deleted (erased) from a CD-RW and DVD-RW/+RW/-RAM disc cannot be recovered. Check the content of the disc carefully before you delete it. If multiple drives that can write data to discs are connected, be careful not to delete data from the wrong drive. In writing to a DVD-R/+R/-RW/+RW disc, some disc space is required for file management, so you may not be able to write the full capacity of the disc. Since the disc is based on the DVD-R/-RW standard, it will be filled with dummy data if the written data is less than about 1 GB. Even if you write only a small amount of data, it might take time to fill in the dummy data. Two types of DVD-R/+R/-RW/+RW/-RAM discs are on the market: data and video. Use a video disc to store video data. You can use video discs on a DVD recorder as well as on your computer's DVD-ROM drive. You cannot use data discs on a DVD recorder. DVD-RAM formatted by FAT32 cannot be read in Windows 2000 without DVD-RAM Driver Software. When multiple drives that can write data to discs are connected, be careful not to write to the wrong drive. Be sure to connect the universal AC adapter before you write or rewrite. Before you enter Sleep/Hibernation Mode, be sure to finish DVD-RAM writing. Writing is finished if you can eject DVD-RAM media. Be sure to close all other software programs except the writing software. Do not run software such as a screen saver, which can put a heavy load on the CPU.

Operate the computer at full power. Do not use power-saving features. Do not write while virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background. Do not use hard disk utilities, including those intended to enhance hard disk access speed, as they may cause unstable operation and damage data. Write from the computer's hard disk drive to the CD. Do not try to write from shared devices such as a LAN server or any other network device. Writing with software other than TOSHIBA Disc Creator or Ulead DVD MovieFactory for TOSHIBA has not been confirmed. Therefore, operation with other software cannot be guaranteed.
Please observe/consider the following when you write or rewrite to a CD-R/ RW, DVD-R/-RW/-RAM or DVD+R/+RW disc. Do not perform any of the following actions when writing or rewriting: Change users in the Windows Vista operating system. Operate the computer for any other function, including using a mouse or TouchPad/Dual Mode Pad or closing/opening the LCD panel. Start a communication application such as a modem. Apply impact or vibration to the computer. Install, remove or connect external devices such as USB devices, an external display, i.Link devices or optical digital devices. Use the audio/video control button to reproduce music or voice. Open the drive. Do not use shut down/log off and Sleep/Hibernation while writing or rewriting. Make sure writing or rewriting is completed before going into Sleep/ hibernation. Writing is completed if you can open the drive tray. Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains or cars. Do not use an unstable surface such as a stand. Keep mobile phones and other wireless communication devices away from the computer. Always copy data from the hard disk drive to the CD. Do not use cutand-paste as the original data will be lost if there is a write error.
How to make a Label Flash DVD
Simplified steps for making a Label Flash DVD: 1. Insert a Label Flash disc in DVD drive. Set printable surface for underside. 2. Click Start All Programs DVD MovieFactory for TOSHIBA Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD MovieFactory. 3. Click Print Disc Label Label Printing. Ulead Label@Onece is started. 4. Click the General tab. 5. Choose DVD Drive for Printer. e.g. <E:> PIONEER DVD. 6. Add and customize the look of your images and text. 7. Click Label Flash setting and choose Draw Quality. 8. Click Print. The availability of Label Flash function depends on the model you purchased.

Satellite P200/Satellite Pro P200 4-31

3. 4.

Please verify your disc after recording important data. DVD-R/+R/-RW disc cannot be written in VR format. Not support to output VCD or SVCD format. About Straight to Disc Not support to record on DVD-R/+R disc Not support to record DVD+VR format by HDV HDV support to burn DVD-Video only DVD-VR format not support to add Menu About recorded DVDs Some DVD-ROM drives for personal computers or other DVD players may not be able to read DVD-R/+R/-RW/-RAM discs. When playing your recorded disc on your computer, please use the DVD Video Player. If you use an over-used rewritable disc, the full formatting might be locked. Please use a brand new disc.
Note the following limitations when you use TOSHIBA Disc Creator: DVD-Video cannot be created using TOSHIBA Disc Creator DVD-Audio cannot be created using TOSHIBA Disc Creator You cannot use the TOSHIBA Disc Creator "Audio CD" function to record music to the DVD-R/-RW or DVD+R/+RW media. Do not use the "Disc Backup" function of TOSHIBA Disc Creator to copy DVD-Video and DVD-ROM with copyright protection. DVD-RAM media cannot be backed up with the "Disc Backup" function of TOSHIBA Disc Creator You cannot back up a CD-ROM or CD-R/RW to DVD-R/-RW or DVD+R/ +RW using the "Disc Backup" function of TOSHIBA Disc Creator. You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW or DVD+R/ +RW to CD-R/RW using TOSHIBA Disc Creator TOSHIBA Disc Creator cannot record in packet format. You might not be able to use the Disc Backup function of TOSHIBA Disc Creator to backup a DVD-R/-RW or DVD+R/+RW disc that was made with other software on a different DVD-R/-RW or DVD+R/+RW recorder. If you add data to a DVD-R and DVD+R disc that you have already recorded to, you might not be able to read the added data under some circumstances. It cannot be read in 16-bit operating systems, such as Windows 98SE and Windows ME, in Windows NT4 you will need Service Pack 6 or later to read the data, and in Windows 2000 you will need Service Pack 2 or later to read it. Some optical media drives cannot read added data regardless of the operating system.

Typewriter keys

The typewriter keys, produce the upper- and lower-case letters, numbers, punctuation marks, and special symbols that appear on the screen. There are some differences, however, between using a typewriter and using a computer keyboard: Letters and numbers produced in computer text vary in width. Spaces, which are created by a space character may also vary depending on line justification and other factors. The lowercase l (el) and the number 1 (one) are not interchangeable on computers as they are on a typewriter. The uppercase O (oh) and the 0 (zero) are not interchangeable. The Caps Lock function key locks only the alphabetic characters in uppercase while the shift lock on a typewriter places all keys in the shifted position. The Shift keys, the Tab key, and the BkSp (backspace) key perform the same function as their typewriter counterparts but also have special computer functions.

F1. F12 function keys

The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys.
F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter. The function executed by individual keys depends on the software you are using.
Soft keys: Fn key combinations
The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features. Some software may disable or interfere with soft-key operations. Soft-key settings are not restored by the Sleep feature.

Emulation keys

Your software may require you to use keys that the keyboard does not have. Pressing the Fn key and one of the following keys simulates the enhanced keyboard's functions.
Press Fn + Enter to simulate Enter on the enhanced keyboard's numeric keypad.
Press Fn + Ctrl to simulate the enhanced keyboard's right Ctrl key.

Hotkeys

Fn + ESC Fn + F1 Volume Mute Turns the volume on and off. Instant Security Enters screen saver mode and blanks the screen. To restore your desktop, press any key or use the TouchPad/Dual Mode Pad. Power Save Modes Displays the power save modes and lets you change the power settings Sleep This hot key switches the system to Sleep mode. Hibernate This hot key switches the system to Hibernate mode. Display Selection Changes displays.
Fn + F2 Fn + F3 Fn + F4 Fn + F5
Default resolution for simultaneous mode is set to WXGA+ (1440x900). If you connect an RGB (Monitor) that is not WXGA+, change it in "Control Panel/Personalization/Display settings". Fn + F6 Fn + F7 Fn + F8 Brightness Down Brightness Up Wireless Device Controls Pressing this hot key allows you to switch between active wireless devices if the wireless communication switch is switched on. TouchPad/Dual Mode Pad On/Off Change Resolution Cycles sequentially from the current resolution to 800x600 to 1024x768 and back again to the original resolution. Zoom Out To reduce the icon size on the desktop or the application window, press the 1 key while holding down the Fn key. Zoom In To enlarge the icon size on the desktop or the application window, press the 2 key while holding down the Fn key.

To enter a password manually, follow these steps: 1. Turn on the power as described in Chapter 3, Getting Started. The following message will appear in the LCD: Enter Password [xxxxxxxx] At this point, the hotkeys Fn + F1 to F9 do not work. They will function after you enter the password. 2. Enter the Password. 3. Press Enter. If you enter the password incorrectly three consecutive times, the computer shuts down. You must turn on the computer again and re-enter the password.

Power-up modes

The computer has three power-up modes: Hibernation (saves data in memory to the hard disk) Sleep (power remains on, maintaining the data in memory, but the CPU and all other devices effectively enter a 'sleep' mode) Boot (does not save data in memory) Refer also to the section Turning off the power in Chapter 3, Getting Started.

Panel power off/on

This feature makes the computer to enter Hibernation when the display panel is closed and turns it back on when the display panel is opened. If the panel power off function is enabled and you use Shut down Windows, do not close the display until the shut down function is completed.
System automatic Sleep/Hibernation
This feature automatically turns off the system in Sleep or Hibernation mode if the computer is not used for a set duration. Refer to Special features, in Chapter 1, Satellite P200/Satellite Pro P200 Series Features for an explanation of how to set the duration.

Chapter 7

HW Setup
This chapter explains how to use the TOSHIBA HW Setup utility to configure your computer. TOSHIBA HW Setup lets you configure settings for various hardware devices through a number of tabs titled General, Password, Display, Boot Priority, Keyboard, CPU, LAN, and USB.

Accessing HW Setup

Start, point to All Programs, point to TOSHIBA, point to Utilities and click HWSetup.

HW Setup Window

The HW Setup window contains the following tabs: General, Password, Display, Boot Priority, Keyboard, LAN, and USB. There are also these three buttons: OK Cancel Apply Accepts your changes and closes the HW Setup window. Closes the window without accepting your changes. Accepts all your changes without closing the HW Setup window.
This window displays the BIOS version and contains two buttons: Default About Return all HW Setup values to the factory settings. Display the HW Setup version.
This field displays BIOS Version and date. When finish BIOS update , please restart your computer and press F2 into BIOS setup manual and load BIOS default one time.

1. Click the Safely Remove Hardware icon on the Task Bar. 2. Point to i.LINK (IEEE1394a) device and click. 3. Disconnect the cable from the computer then from the i.LINK device. Refer also to the documentation that came with your i.LINK device.

Security lock

A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the right side of the computer.

Chapter 9

Troubleshooting
TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.

Problem solving process

Resolving problems will be much easier if you observe the following guidelines: Stop immediately when you recognize a problem exists. Further action may result in data loss or damage. You may destroy valuable problemrelated information that can help solve the problem. Observe what is happening. Write down what the system is doing and what actions you performed immediately before the problem occurred. If you have a printer attached, print a copy of the screen using PrtSc. Isolate the problem. Using the tools available to you, such as the troubleshooting tips in this chapter, try to discover the specific actions that caused the problem. The questions and procedures offered in this chapter are meant as a guide, they are not definitive problem solving techniques. Many problems can be solved simply, but a few may require help from your dealer. If you find you need to consult your dealer or others, be prepared to describe the problem in as much detail as possible.

Preliminary checklist

Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device. Make sure all options are set properly in the setup program. Check all cables. Are they correctly and firmly attached? Loose cables can cause signal errors. Inspect all connecting cables for loose wires and all connectors for loose pins. Check that the optical disc drive is correctly inserted. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster.

9-14 Satellite P200/Satellite Pro P200
Problem Cannot write correctly
Procedure If you have trouble writing, make sure you are observing the following precautions: Use only media recommended by TOSHIBA. Do not use the mouse or keyboard during writing. Use only the software supplied with the computer for recording. Do not run or start other software during writing. Do not jar the computer during writing. Do not connect/ disconnect external devices or install/remove internal cards during writing. If problems persist, contact your dealer.
DVD Super Multi drive with double layer disc recording support
For more information, refer to Chapter 4, Operating Basics. Problem You cannot access a disc in the drive Procedure Make sure the drive's drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the disc is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the disc. Make sure there is no obstruction. Remove any foreign object. Check whether the disc is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. See the Media care section in Chapter 4 for details on cleaning.
The software or hardware configuration may be Some discs run correctly, but others do causing a problem. Make sure the hardware configuration matches your software's needs. not Check the disc's documentation. Check the type of disc you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video, DVD-R, DVD-RW, DVD+R, DVD+RW, DVDRAM, DVD+R (Double Layer) , DVD-R (dual Layer) CD-ROM: CD-DA, CD-Text, Photo CD (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), CD-G (Audio CD only) Check the region code on the DVD. It must match that on the DVD Super Multi drive. Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: Use only media recommended by TOSHIBA. Do not use the mouse or keyboard during writing. Use only the software supplied with the computer for recording. Do not run or start other software during writing. Do not jar the computer during writing. Do not connect/ disconnect external devices or install/remove internal cards during writing. If problems persist, contact your dealer.

Disk drive

For information on disk care refer to Chapter 4, Operating Basics. Problem Procedure
The software or hardware configuration may be Some programs run correctly, but others do causing a problem. Make sure the hardware configuration match's your software's needs. not You cannot access the Try another disk. If you can access this disk, the disk drive original disk (not the disk drive) is problem. If problems persist, contact your dealer.

Glossary-3

DC: Direct Current. Electric current that flows in one direction. This type of power is usually supplied by batteries. default: The parameter value automatically selected by the system when you or the program do not provide instructions. Also called a preset value. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information. disk drive: The device that randomly accesses information on a disk and copies it to the computers memory. It also writes data from memory to the disk. To accomplish these tasks, the unit physically rotates the disk at high speed past a read-write head. display: A CRT, LCD, or other image producing device used to view computer output. DOS: Disk Operating System. See operating system. driver: A software program, generally part of the operating system, that controls a specific piece of hardware (frequently a peripheral device such as a printer or mouse). DVD-RAM: A Digital Versatile Disc Random Access Memory is a highcapacity, high performance disc that lets you store large volumes of data. The DVD-ROM drive uses a laser to read data from the disc. DVD-ROM: A Digital Versatile Disc Read Only Memory is a high capacity, high performance disc suitable for play back of video and other highdensity files. The DVD-ROM drive uses a laser to read data from the disc.
execute: To interpret and execute an instruction.
floppy disk: A removable disk that stores magnetically encoded data. floppy disk drive (FDD): An electromechanical device that reads and writes to floppy disks. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk. function keys: The keys labeled F1 through F12 that tell the computer to perform certain functions.

Glossary-4

gigabyte (GB): A unit of data storage equal to 1024 megabytes. See also megabyte. graphics: Drawings, pictures, or other images, such as charts or graphs, to present information.
hard disk: A non-removable disk usually referred to as drive C. The factory installs this disk and only a trained engineer can remove it for servicing. Also called fixed disk. hard disk drive (HDD): An electromechanical device that reads and writes a hard disk. See also hard disk. hertz: A unit of wave frequency that equals one cycle per second. hot key: The computers feature in which certain keys in combination with the extended function key, Fn, can be used to set system parameters, such as speaker volume.
input: The data or instructions you provide to a computer, communication device or other peripheral device from the keyboard or external or internal storage devices. The data sent (or output) by the sending computer is input for the receiving computer. I/O: Input/output. Refers to acceptance and transfer of data to and from a computer. I/O devices: Equipment used to communicate with the computer and transfer data to and from it.

VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFHREN VON ANDEREN VORGNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KNNEN GEFHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN.

Modem warning notice

Conformity Statement
The equipment has been approved to [Commission Decision "CTR21"] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance.
Network Compatibility Statement
This product is designed to work with, and is compatible with the following networks. It has been tested to and found to confirm with the additional requirements conditional in EG 201 121. Germany Greece Portugal Spain Switzerland Norway All other countries/ regions ATAAB AN005, AN006, AN007, AN009, AN010 and DE03, 04, 05, 08, 09, 12, 14, 17 ATAAB AN005, AN006 and GR01, 02, 03, 04 ATAAB AN001, 005, 006, 007, 011 and P03, 04, 08, 10 ATAAB AN005, 007, 012, and ES01 ATAAB AN002 ATAAB AN002, 005, 007 and NO 01, 02 ATAAB AN003, 004
Specific switch settings or software setup are required for each network, please refer to the relevant sections of the user guide for more details. The hookflash (timed break register recall) function is subject to separate national type approvals. It has not been tested for conformity to national type regulations, and no guarantee of successful operation of that specific function on specific national networks can be given.
xviii Satellite P200/Satellite Pro P200

Japan regulations

Region selection
If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan country mode. It is illegal to use the modem in Japan with any other selection.

Redial

Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer. Japan's Telecommunications Business Law permits up to two redials on analogue telephones, but the redials must be made within a total of three minutes. The internal modem is approved by Japan Approvals Institute for Telecommunications Equipment.

A05-0413001

Pursuant to FCC CFR 47, Part 68:
When you are ready to install or use the modem, call your local telephone company and give them the following information: The telephone number of the line to which you will connect the modem The registration number that is located on the device US: AGSMD01BDELPHI The FCC registration number of the modem will be found on either the device which is to be installed, or, if already installed, on the bottom of the computer outside of the main system label. The Ringer Equivalence Number (REN) of the modem, which can vary. For the REN of your modem, refer to your computer's user's guide. The modem connects to the telephone line by means of a standard jack called the USOC RJ11C.

Conventions

This manual uses the following formats to describe, identify, and highlight terms and operating procedures.

Abbreviations

On first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition. For example: Read Only Memory (ROM). Acronyms are also defined in the Glossary.
Icons identify ports, dials, and other parts of your computer. The indicator panel also uses icons to identify the components it is providing information on.
The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, Enter identifies the Enter key.

Key operation

Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third. DISKCOPY A: B: When procedures require an action such as clicking an icon or entering text, the icon's name or the text you are to type in is represented in the type face you see to the left.

Display

Names of windows or icons or text generated by the computer that appears on its display screen is presented in the type face you see to the left.

xxxiii

Messages
Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below. Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment. Please read. A note is a hint or advice that helps you make best use of your equipment.

Terminology

This term is defined in this document as follows: Start The word Start refers to the Microsoft Windows Vista. button in

Equipment checklist

Carefully unpack your computer. Save the box and packing materials for future use. Check to make sure you have all the following items:

Hardware

Sleep Mode limitations

Sleep Mode will not function under the following conditions: Power is turned back on immediately after shutting down. Memory circuits are exposed to static electricity or electrical noise.

Hibernation mode

The Hibernation Mode feature saves the contents of memory to the hard disk drive when the computer is turned off so that, the next time it is turned on, the previous state is restored. Please note that the Hibernation Mode feature does not save the status of any peripheral devices connected to the computer. Save your data. While entering Hibernation Mode, the computer saves the contents of memory to the hard disk drive. However, for safety sake, it is best to save your data manually. Data will be lost if you remove the battery or disconnect the AC adaptor before the save is completed. Wait for the Hard Disk Drive indicator to go out. Do not install or remove a memory module while the computer is in Hibernation Mode. Data will be lost.
Benefits of Hibernation Mode
The Hibernation Mode feature provides the following benefits: Saves Data to the hard disk drive when the computer automatically shutsdown because of a low battery condition. You can return to your previous working environment immediately when you turn on the computer. Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature. Allows the use of the panel power off feature.
Starting Hibernation Mode
You can also enable Hibernation Mode by pressing Fn + F4 - please refer to Chapter 6, The Keyboard, for further details. To enter Hibernation Mode, follow the steps below. 1. Click Start. 2. Click the arrow button ( ) in the power management buttons ( ). 3. Select Hibernate from the menu.
Automatic Hibernation Mode
The computer can be configured to enter Hibernate Mode automatically when you press the power button or close the lid. In order to define these settings, you can follow the steps as described below: 1. Click Start and click the Control Panel. 2. Click System and Maintenance and click Power Options. 3. Click Choose what the Power Button do or Choose what closing the lid does. 4. Enable the desired Hibernation Mode settings for When I press the power button or When I close the lid. 5. Click the Save Changes button.
Data save in Hibernation Mode
When you turn off the power in Hibernation Mode, the computer takes a moment to save the current data in memory to the hard disk drive. During this time, the Hard Disk Drive indicator will glow. After you turn off the computer, and the content of memory has been saved to the hard disk drive, turn off the power to any peripheral devices. Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.

Window Logon via FingerPrint Authentication
If required, you are also able to use FingerPrint authentication in place of the usual Windows logon process using your username and password. This method is specially useful where there are many users using the same computer as it removes the need for actual user selection when the system is started.
FingerPrint Authentication Procedure
1. Start up the computer. 2. At the Logon Authorization screen, choose any of the enrolled fingers and swipe the FingerPrint on the sensor - If the authentication process is successful, the user will automatically be logged into Windows. If the FingerPrint authentication process fails you will need to log into Windows using the appropriate username and password. In addition, you should use this manual login process if Finger Print authentication fails for three consecutive tries - a warning message will be displayed when authentication is not normal or is not successful within a fixed duration.
FingerPrint Power-on Security

General

The FingerPrint authentication system can be used to replace the keyboard based password authentication system that is used when the computer is turned on. If you do not want to use the FingerPrint authentication system for password authentication when the computer is turned on, but instead prefer to use the keyboard entry method instead, simply press the Back Space key or the ESC/Rotation button when the FingerPrint Power-on Security screen is displayed. Using this process will switch the password input screen across to the keyboard based entry screen. You must ensure that you use the TOSHIBA Password Utility to register a User Password before using the FingerPrint Power-on Security and its extended function to allow FingerPrint to be used to access the computer when it is turned on. If the FingerPrint authentication process fails five times, a preset time limit is exceeded, or you press the Back Space key, [Password=] will be displayed on the screen and you will have to enter either the User Password or Supervosor Password manually in order to start the computer. When swipe your finger, please ensure you do it slowly and at a constant speed. If you find that this does not improve the authentication rate, you should try to adjust the speed at which the finger is swiped. If there are any changes in the environment or setting related to authorization, you will be required to provide authorization information such as a User Password (and, if applicable, the HDD (Hard Disk Drive) password).

IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 3. Do not use the telephone to report a gas leak in the vicinity of the leak. 4. Use only the power cord indicated in this manual.
Telecommunication regulations vary from one country/region to another, so you will need to make sure the internal modem's settings are correct for the country/region in which it will be used. 1. Open the Modem Region Select application. It is located on the Programs menu at TOSHIBA Networking Modem Region Select.
Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available. If you change the Country/ Region in the Control Panel, the change may not take effect. 2. The Region Selection icon appears on the Windows Task Bar.
The Region Selection icon
3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location. 4. Select a region from the region menu or a telephony location from the submenu. When you click a region it becomes the modem's region selection, and the New Location for telephony will be set automatically. When you select a telephony location, the corresponding region is automatically selected and it becomes the modem's current region setting.

Properties menu

Click the icon with the secondary mouse button to display the following menu.

The properties menu

You can enable or disable the following settings:

AutoRun Mode

Region Select Utility starts automatically when you start up the operating system.
Open the Dialling Properties dialogue box after selecting region.
The dialling properties dialogue box will be displayed automatically after you select the region.
4-14 Satellite P200/Satellite Pro P200
Location list for region selection.

Bluetooth wireless technology
Bluetooth wireless technology eliminates the need for cables between electronic devices such as desktop computers, printers and mobile phones. Bluetooth wireless technology has the following features:

Worldwide operation

The Bluetooth radio transmitter and receiver operate in the 2.4 GHz band, which is license-free and compatible with radio systems in most countries in the world.

Radio links

You can easily establish links between two or more devices. The link is maintained even if the devices are not within line of sight.
Two advanced security mechanisms ensure a high level of security: Authentication prevents access to critical data and makes it impossible to falsify the origin of a message. Encryption prevents eavesdropping and maintains link privacy.
Bluetooth Stack for Windows by TOSHIBA
Please note that this software is specifically designed for the following operating systems: Microsoft Windows Vista Detailed information regarding the use with these operating systems is listed below. Please refer also to the electronic information which is included with each software. This Bluetooth Stack is based on Bluetooth Version 1.1/1.2/2.0+EDR specification. TOSHIBA cannot confirm compatibility between any PC products and/or other electronic devices that use Bluetooth other than TOSHIBA mobile PCs.
Release Notes related to the Bluetooth Stack for Windows by TOSHIBA
1. Fax application software: Regarding FAX application software, there are some software that you cannot use on this Bluetooth Stack. 2. Multi User: On Windows Vista, the use of Bluetooth is not supported in a multi-user environment. This means that, when you use Bluetooth, other users logged onto the same computer will not be able to use its Bluetooth functionality.

Product Support:

The latest information regarding Operating System support, Language Support or available upgrades can be found on our web site http:// www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or www.pcsupport.toshiba.com in the United States.

TOSHIBA HD DVD PLAYER

"TOSHIBA HD DVD PLAYER" software is supported for playback of HD DVD Video, DVD-Video and DVD-VR. The "TOSHIBA HD DVD PLAYER" does not have a parental control function. In order to protect copyrights, the Windows Print Screen function is disabled when "TOSHIBA HD DVD PLAYER" is running. Print Screen functions are disabled even when running other applications besides "TOSHIBA HD DVD PLAYER" and when "TOSHIBA HD DVD PLAYER" is minimized. Please close the "TOSHIBA HD DVD PLAYER" to use the Print Screen function. Carry out the installation/uninstallation of the "TOSHIBA HD DVD PLAYER" under a user account with administrator rights. Do not change Windows Users while "TOSHIBA HD DVD PLAYER" is running. Some HD DVD Video disc titles may return to the title before the playback time (playback position) displayed in the control window reaches the end time. For some HD DVD Video discs, using the control window to change the audio track will also change the subtitle track. Periodic updates will be necessary to continue using the "TOSHIBA HD DVD PLAYER".
Using TOSHIBA HD DVD PLAYER
Starting TOSHIBA HD DVD PLAYER
Use the following procedure to start "TOSHIBA HD DVD PLAYER". 1. Insert an HD DVD-Video in the HD DVD drive while Windows VistaTM. is running. When an HD DVD-Video disc and an HD DVD (Twin format disc) are set in the HD DVD drive, the following application selection screen may appear. If this occurs, select Play HD DVD movie or Run the HD DVD Launcher, then click OK to launch the TOSHIBA HD DVD PLAYER.
Application selection screen
2. Touch the CD/DVD panel on the Front operation panel. Or select Start -> All Programs -> TOSHIBA HD DVD PLAYER to start "TOSHIBA HD DVD PLAYER". The TOSHIBA DVD PLAYER can also be started from the Media Center top menu.
Operating TOSHIBA HD DVD PLAYER
Important information on using "TOSHIBA HD DVD PLAYER".

Before Connecting

Please refer to the television's user manual as well as this chapter when connecting the computer to a television. Televisions Which Can Be Connected to the Computer. Televisions which are equipped with an HDMI input port can be connected to the computer. Please use a commercially available HDMI cable to connect the television and computer. Not all televisions equipped with an HDMI input port have been tested for compatibility with this product. As such, Toshiba cannot guarantee that HD DVD-Video content can be displayed on all televisions equipped with an HDMI input port. HD DVD-Video content may not display properly on some televisions.
Connecting to the Computer
Turn off the television and computer before connecting. 1. Insert the HDMI cable plug into the HDMI out port on the computer.

HDMI out port

Connecting the HDMI out port
2. Insert the remaining HDMI cable plug into the HDMI input port on the television. 3. Turn on the television first, and then the computer. Audio will be output from both the television and the computer. The volume dial or FN + ESC keys can be used to mute the computer audio. The volume level for both the television and computer can be adjusted using the WAVE item in "Volume Control".
5-12 Satellite P200/Satellite Pro P200
Switching between Computer and Television Display
The following method can be used to display HD DVD-Video. The display method can be changed by changing the display device setting. Configure the following settings to display HD DVD-Video on the television. If the following settings are not configured, HD DVD-Video will not be displayed on the television.

Notes on Operation

Change the display device setting before playing HD DVD-Video. Do not change the display device while playing HD DVD-Video. Do not change the display device at the following times. When reading or writing data When carrying out communications operations HD DVD-Video cannot be played when using Clone or Dualview (extended desktop) displays modes. Set either the computer's display panel or the television as the sole display device. The display device setting can be changed using the FN + F5 keys. When you press these hot keys, a dialog box appears. Only selectable devices will be displayed. Hold down FN and press F5 again to change the device. When you release FN and F5, the selected device will change. If you hold down these hot keys for five seconds the selection will return to the computers display panel.
HD DVD-R Disc writing Software
Ulead DVD MovieFactory for TOSHIBA and TOSHIBA Disc Creator are included with this computer for writing HD DVD-R discs. Ulead DVD MovieFactory can be used to write files in video format. TOSHIBA Disc Creator can be used to write data. Refer to the manuals or help files included with the software for detailed usage instructions. Methods for accessing the manuals and help files for the software are as follows. Opening the Ulead DVD MovieFactory Software Start -> All Programs -> DVD MovieFactory for TOSHIBA -> Ulead DVD MovieFactory for TOSHIBA Launcher Opening the Ulead DVD MovieFactory Manual Start -> All Programs -> DVD MovieFactory for TOSHIBA -> User Manual -> DVD MovieFactory User Manual Opening the TOSHIBA Disc Creator Software Start -> All Programs -> CD&DVD Applications -> Disc Creator Opening the TOSHIBA Disc Creator Manual Start -> All Programs -> CD&DVD Applications -> Disc Creator Help

Writing CDs/DVDs/HD DVDs on a HD DVD-R drive
You can use the HD DVD-R drive to write data to either CD-R/RW or DVDR/-RW/+R/+RW/-RAM or HD DVD-R discs. The following applications for writing are preinstalled: TOSHIBA Disc Creator/ Direct Disc Writer. Ulead DVD MovieFactory for TOSHIBA, which is a product of Ulead Systems, Inc.
Before you write or rewrite to CD-R/RW or DVD-R/-RW/+R/+RW/-RAM or HD DVD-R media, read and follow all set-up and operating instructions in this section. If you fail to do so, the HD DVD-R drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage.
TOSHIBA does not bear responsibility for the following: Damage to any CD-R/RW or DVD-R/-RW/+R/+RW/-RAM or HD DVD-R disc that may be caused by writing or rewriting with this product. Any change or loss of the recorded contents of CD-R/RW or DVD-R/RW/ +R/+RW /-RAM or HD DVD-R media that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents. Damage that may be caused by using third party equipment or software.
Please observe the following points when you write or rewrite data. Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW, DVD-R/+R/-RW/+RW/-RAM and HD DVD-R media. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYOYUDEN CO., LTD. MITSUBISHI KAGAKU MEDIA CO., LTD RICOH Co., Ltd. Hitachi Maxell Ltd. MITSUBISHI KAGAKU MEDIA CO., LTD RICOH Co., Ltd. DVD Specifications for Recordable Disc for General Version 2.0 TAIYOYUDEN CO., LTD. Matsushita Electric Industrial Co., Ltd. DVD Specifications for Re-recordable Disc for Version 1.1 or Version 1.2 VICTOR COMPANY OF JAPAN, LIMITED MITSUBISHI KAGAKU MEDIA CO., LTD MITSUBISHI KAGAKU MEDIA CO., LTD RICOH Co., Ltd. MITSUBISHI KAGAKU MEDIA CO., LTD RICOH Co., Ltd. DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Matsushita Electric Industrial Co., Ltd. Hitachi Maxell Ltd. *DVD Multi drive and DVD Super Multi can use DVDRAM. MITSUBISHI KAGAKU MEDIA CO., LTD

DVD+R (Double Layer)

DVD-R (Dual Layer) HD DVD-R (Single Layer) HD DVD-R (Dual Layer)

Caution

1. Never continue to use a battery pack after its recharging capacity has become impaired, or after the display of a warning message indicating that the battery pack's power is exhausted. Continued use of an exhausted or impaired battery pack could cause the loss of data. 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling centre to save resources and prevent environmental damage. Cover the terminals with electrical tape to prevent short-circuits, which could cause the battery pack to ignite or rupture. 3. Use only battery packs recommended by TOSHIBA as replacements. 4. Always make sure the battery pack is installed correctly and securely. Otherwise, a battery pack could fall out and possibly cause injury.
7-6 Satellite P200/Satellite Pro P200
5. Charge the battery pack only in an ambient temperature between 5 and 30 degrees Celsius. Otherwise, the electrolyte solution might leak, battery pack performance might deteriorate and the battery life might be shortened. 6. Be sure to monitor the remaining battery power. If the battery pack or real time clock battery discharge completely, Sleep Mode will not function, and data in memory will be lost, and the computer might register an incorrect time and date. In this case, connect the AC adapter to recharge the batteries. 7. Never install or remove the battery pack without first turning off the power and disconnecting the AC adapter. Never remove the battery pack while the computer is in Sleep Mode as data will be lost.
1. Never remove the battery pack while the Wake-up on LAN function is enabled. Data will be lost. Before you remove a battery pack, disable the Wake-up on LAN function. 2. To ensure the battery pack maintains maximum capacity, operate the computer on battery power once a week until the battery pack is fully discharged. Refer to the section Extending battery life in this chapter for procedures. If the computer is continuously operated on AC power for an extended period, more than a week, the battery might fail to retain a charge. It might not function efficiently over the expected life of the battery pack and the Battery indicator might not indicate a low-battery condition. 3. After the battery pack is charged, avoid leaving the AC adapter connected and the computer turned off for more than a few hours at a time. Continuing to charge a fully charged battery pack can damage the battery.

Charging the batteries

When the power in the battery pack becomes low, the Battery indicator flashes amber indicating that only a few minutes of battery power remain. If you continue to use the computer while the Battery indicator flashes, the computer enables Hibernation mode (so you don't lose data) and automatically turns off. You must recharge a battery pack when it becomes discharged.

Memory expansion

You can install additional memory in the computer's memory module socket to increase the amount of RAM. This section describes how to install and remove a memory module. Before you install or remove a memory module, turn off the computer with the Shut Down option in the Windows Start menu. If you install or remove a memory module while the computer is in Sleep or Hibernation mode, data will be lost. Some memory modules can be physically installed but are not compatible with the computer. In this case the computer will issue a warning. CAUTION: If you want to upgrade system memory, you should only use certified modules. Ask your vendor or check the TOSHIBA web site for a list of approved memory products.
Satellite P200/Satellite Pro P200 9-5
Insert the two memory modules of the same specifications and capacity into Slot A (Upper) and Slot B (Bottom) respectively. The computer will operate in dual channel mode. You can access the inserted memory modules efficiently in dual channel.
Point to note about Memory Module Error
If you install a memory module that is not compatible with the computer, the Power indicator will flashes (on for 0.5 seconds, off for 0.5 seconds) in the following ways: If there is only an error in Slot A: repeatedly flashes orange twice, then blue. If there is only an error in Slot B: repeatedly flashes orange, then blue twice. If there is an error in Slot A and in Slot B: repeatedly flashes orange twice, then blue twice. In all instances you should shut down the computer and remove the incompatible module(s).
Installing Memory on Bottom Side
If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. Follow these steps to install a memory module: 1. Set the computer to boot mode and turn off the power. Do not try to install a memory module under the following conditions. You can damage the computer and the module. a. The computer is turned on. b. The computer was shut down using the Stand by mode. c. Power to the optical disc drive has been turned on by the CD Power switch. Remove all cables connected to the computer. Turn the computer upside down and remove the battery, refer to Chapter 7, Power and Power-Up Modes. Loosen the one screw securing the memory module socket cover. Slide your fingernail or a thin object under the cover and lift it off.

2. 3. 4. 5.

Removing the memory module socket cover
6. Fit the module's connectors into the computer's connectors at about a 45 degree angle and press the module carefully to ensure a firm connection. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. 7. Push the module down so it lies flat. Latches on either side will click into place to secure the module.

Live TV

DVD Menu Numbers

Clear Enter

Using the Remote Controller
This computer includes a remote control unit, which allows you to control some of your computers from distant location. The Remote Controller is designed specially for this computer. Some application programs may not support remote control functions.
Operational range of the Remote Controller
Point the Remote controller at your computer and press a button. The operational angle and distance are described below. Distance Angle Within 5m from the infrared receiver window. Within a 30 degree horizontal and 15 degree vertical range oof the infrared receiver window.
30 degrees 15 degrees (vertically) Infrared receiver window 30 degrees 15 degrees (vertically) 5m Remote Controller
*The appearance of the provided Remote Controller may vary from model to model.
Operation range of the remote control
Even if within the effective scope as described above, the remote control may malfunction or not work correctly in the following cases. When an obstacle stands between the infrared receiver window or your computer and the Remote Controller. When direct sunlight or strong fluorescent light strikes the infrared receiver window. When the infrared receiver window or the infrared emission part of the Remote Controller is dirty. When other computers which use an infrared remote controller are used near to your computer. When a low battery condition is present.
Installing/Removing batteries
Be sure to install the dry batteries provided with this product using the Remote Controller. The procedures for installing and removing the bateries vary depending on the type of the Remote Controller. Check the type and then install or remove the bateries as instructed. Store the battery for the remote control beyond the reach of children. If a child swallows a battery, this might result in chocking. If it happens, contact a doctor immediately. Observe the following precautions when using the battery of the Remote Controller. Do not use batteries other than those specified. Ensure that you insert the batteries with their polarities correctly aligned(+ or -) Do not recharge, heat, disassemble or shot the battery, or put it into a fire or flame. Do not use a battery whose recommended expiration date has been reached, or is completely discharged. Do not use different type of battery or old and new batteries at the same time. Do not carry the battery together with metal necklaces, hairpins or other metal accessories. When storing or disposing of used batteries, make sure to put some insulation tape on their terminal (+ and -) to avoid short-circuits. If these precausions are not followed, heating, fluid leakage or explosion may occur. This may cause bums or personal injury. If battery fluid gets on your skin or clothes, wash immediately with clean water. If battery fluid gets in your eyes, rinse your eyes with clean water immediately and see a doctor. Do not touch the battery fluid on instruments or devices with bare hands. Wipe off with a cloth or paper towel.

Glossary-3

DC: Direct Current. Electric current that flows in one direction. This type of power is usually supplied by batteries. default: The parameter value automatically selected by the system when you or the program do not provide instructions. Also called a preset value. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information. disk drive: The device that randomly accesses information on a disk and copies it to the computers memory. It also writes data from memory to the disk. To accomplish these tasks, the unit physically rotates the disk at high speed past a read-write head. display: A CRT, LCD, or other image producing device used to view computer output. DOS: Disk Operating System. See operating system. driver: A software program, generally part of the operating system, that controls a specific piece of hardware (frequently a peripheral device such as a printer or mouse). DVD-RAM: A Digital Versatile Disc Random Access Memory is a highcapacity, high performance disc that lets you store large volumes of data. The DVD-ROM drive uses a laser to read data from the disc. DVD-ROM: A Digital Versatile Disc Read Only Memory is a high capacity, high performance disc suitable for play back of video and other highdensity files. The DVD-ROM drive uses a laser to read data from the disc.
execute: To interpret and execute an instruction.
floppy disk: A removable disk that stores magnetically encoded data. floppy disk drive (FDD): An electromechanical device that reads and writes to floppy disks. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk. function keys: The keys labeled F1 through F12 that tell the computer to perform certain functions.

Glossary-4

gigabyte (GB): A unit of data storage equal to 1024 megabytes. See also megabyte. graphics: Drawings, pictures, or other images, such as charts or graphs, to present information.
hard disk: A non-removable disk usually referred to as drive C. The factory installs this disk and only a trained engineer can remove it for servicing. Also called fixed disk. hard disk drive (HDD): An electromechanical device that reads and writes a hard disk. See also hard disk. hertz: A unit of wave frequency that equals one cycle per second. hot key: The computers feature in which certain keys in combination with the extended function key, Fn, can be used to set system parameters, such as speaker volume.
input: The data or instructions you provide to a computer, communication device or other peripheral device from the keyboard or external or internal storage devices. The data sent (or output) by the sending computer is input for the receiving computer. I/O: Input/output. Refers to acceptance and transfer of data to and from a computer. I/O devices: Equipment used to communicate with the computer and transfer data to and from it.