If the camera has not been used for a prolonged period or if you will use the camera for an important event, check the operation of all the camera controls or take the camera to your nearest Canon Service Center.

LCD Displays

By their nature, LCD displays react more slowly at low temperatures, and may appear dark at high temperatures. The display will return to normal at room temperature.

Batteries

Before installing the batteries, wipe the battery contacts to remove any fingerprints and smudges. This is to prevent faulty connections and corrosion. Never disassemble or recharge the batteries. Also, never store a battery in high-temperature places or short circuit the battery contacts or toss a battery into a fire. Although the batteries work well even at low temperatures, battery performance may decline slightly at freezing temperatures. In such a case, keep spare batteries warm in a pocket, etc., and use and warm the batteries alternately.
How Low Battery Levels Affect Camera Operation
On the LCD panel, if the <> icon blinks or it is not displayed, a proper exposure can still be obtained as long as the shutter releases. However, when the battery level is low, film advance and auto rewind might stop midway or not work at all and <> icon may blink on the LCD panel. After the batteries are replaced with new ones, film advance will be possible and film rewind can resume by pressing the <> button.

Lens Electrical Contacts

After detaching the lens from the camera, put on the lens caps or put down the lens with the rear end up to avoid scratching the lens surface and electrical contacts.

Contacts

Nomenclature
Reference page numbers are indicated by (p.).
Built-in flash / AF-assist beam (p.44/19) <^> Film advance mode / Self-timer/*Remote control button (p.32/23/24) Mode Dial (p.10) <l> Main Dial Shutter button (p.14) *Remote control sensor / Self-timer/ *Remote control lamp (p.24/23/24) Grip / Battery compartment (p.11) Red-eye reduction lamp (p.22) Hot shoe Flash-sync contact <M> Flash button (p.44) <> Film plane mark Strap mount (p.7) Remote control terminal**
Lens release button (p.13) Depth-of-field preview button(p.42) Focus mode switch (p.13) Zooming ring Focusing ring (p.31)

Body cap (p.13)

* DATE Model only **For Remote Switch RS-60E3 (sold separately).
Viewfinder eyepiece Eyecup (p.26) Film check window Back cover release lever (p.15) LCD panel (p.8)
<4> AF mode/*SET button p.28/26) < > Aperture set/Exposure compensation button (p.37/39) <j> AE lock/FE lock button (p.41/46) <3> AF point selection button (p.29) AF point selection keys (p.29) <\> Function button (p.22, 25, 26, 40, 42, 43, 44, 47) <> Midroll rewind button (p.16) Guide hole Battery compartment cover release lever (p.11) Battery compartment cover (p.11)

Tripod socket <6> LCD panel illumination button Back cover

Attaching the Strap

Pass the end of the strap through the cameras strap mount from the bottom. Then pass it through the straps buckle as shown in the illustration. Pull the strap to make sure it does not slip out of the buckle. The eyepiece cover is also attached to the strap. (p.24)

Eyepiece cover

LCD Panel
Shutter speed ISO film speed Date FE lock DATE Model Shooting mode icon AF Mode One-Shot AF AI Focus AF AI Servo AF Battery level mark <?> Manual focus Aperture value Red-eye reduction setting AEB amount Date
Date ISO film speed Red-eye reduction Beeper Safety release lock Multiple exposures AEB Custom Function <>> Function pointer Frame counter Multiple-exposure setting Self-timer operation Remote control operation Custom Function icon Exposure level indicator Exposure compensation amount AEB level Red-eye reduction lamp-on indicator Film transport indicator
<=> Film mark Film advance mode <J> Single frame <H> Continuous shooting <> Self-timer/ Remote control Non-DATE Model
Pressing the <6> button illuminates the LCD panel.
The actual display will show only the applicable items.

Viewfinder Information

AF points (7) Superimposed display Focusing screen
<j> AE lock / FE lock AEB in progress <M> Flash-ready Improper FE lock warning <|> *High-speed sync (FP flash) Shutter speed FE lock
<n> Focus confirmation light Exposure level indicator Exposure compensation amount AEB level Red-eye reduction lamp-on indicator Aperture value
Remove the eyecup, then slide the dioptric adjustment lever left or right until the AF points in the viewfinder look sharp.
* With an EX-series Speedlite.

Mode Dial

The dial is divided into two zones.

Full Auto

Im a g e Zon

B a sic Zone

1 Basic Zone
Fully automatic mode where the camera takes care of everything. Y : Full Auto (p.18) Basically, all you do is point and shoot. Image Zone (p.20) Fully automatic modes for a particular subject. U : Portrait I : Landscape O : Close-up P : Sports A : Night Portrait S : Flash off

detach it.

Keep the removed caps where you will not lose them. <AF> stands for Auto Focus, and <MF> stands for Manual Focus. An EF-S lens cannot be attached to the camera.
How the Shutter Button Works
The shutter button has two stages. You can press it down halfway or fully. The two levels of shutter button operation are as follows:
When it is pressed halfway:
Pressing the shutter button down
halfway activates autofocusing (AF), and also activates the automatic exposure (AE) mechanism and sets the shutter speed and aperture value. The exposure (the combination of shutter speed and aperture value) appears on the LCD panel and in the viewfinder ().
When it is pressed fully:
The shutter is released to take the
picture and the film advances by one frame.
If an Extender (optional) is used and the maximum aperture (the lowest f/number) of the lens becomes smaller than f/5.6, autofocusing will not operate. For details, refer to the extender's instructions. Camera movement during the moment of exposure is called camera shake. Camera shake can cause blurred pictures. To prevent blurred pictures due to camera shake: Hold the camera steady. Firmly grasp the camera grip with your right hand, and press your both elbows lightly against your body. Hold the lens at the bottom with your left hand. Press the camera against your face and look through the viewfinder. To maintain a stable stance, place one foot in front of the other instead of lining up both feet. Use your finger tip to touch the shutter button, grasp the camera with your entire right hand, then press the shutter button gently.
=Loading and Unloading Film

Loading Film

After you load the film, the camera first winds the entire roll onto the cameras take-up spool. With DX-coded film, the camera automatically sets the films ISO speed. Then each time a picture is taken, one frame of film is rewound back into the film cartridge. The frame counter shows always number of shots remaining.
Mode Dial to 1 Turn theexcept <:>.any setting 2 Open the back cover. the film 3 Insert angle. cartridge at a slight film leader 4 Align the mark. edge with the <>
pulling out the film leader. If you pull out the film leader too much, rewind it back into the film cartridge.

The built-in flash or any external Speedlite will not fire.
FUsing Red-eye Reduction (with the built-in flash)
When flash is used in a low-light environment, the subjects eyes may come out red in the photograph. To reduce this Red eye the red-eye reduction lamp shines a light into the subjects eyes before the flash is fired. Red-eye reduction works in all shooting modes except <I> <P> <S>.
Move arrow to the 1 <F> the <>>the LCD panel. icon on
the <\> button to move the arrow. ()
Look at the LCD panel and press
Turn the <l> dial 2 on the LCD panel. to set
Press the shutter button halfway to return to normal camera operation. To cancel red-eye reduction, set

on the LCD panel.

When you press the shutter button halfway, the red-eye reduction lamp-on indicator will appear in viewfinder and on the LCD panel. Red-eye reduction Red-eye reduction will not work unless lamp-on indicator the subject looks at the red-eye reduction lamp. Tell the subject to look at the lamp. For maximum effectiveness, press the shutter button fully after the red-eye reduction lamp turns off (after 1.5 sec.). You can take a picture even while the red-eye reduction lamp is lit. The effectiveness of red-eye reduction varies depending on the subject. To further increase the effectiveness of red-eye reduction, go to a brighter environment or move closer to the subject.

qSelf-timer Operation

You can use self-timer in any Basic mode or Creative mode. We recommend using a tripod when you use the self-timer.
button. 1 Press the <^> LCD panel, While looking at the
press the <^> button to select <>.
2 Take the picture. procedure is the The picture-taking
same as with the <Y> Full Auto mode on page 18. Look through the viewfinder and press the shutter button fully to start the self-timer. s The picture will be taken about 10 sec. later. First 8 sec.: Self-timer lamp blinks slowly. Final 2 sec.: Self-timer lamp blinks quickly. s During the self-timer operation, the LCD panel counts down the seconds until the picture is taken.
Do not stand in front of the camera when you press the shutter button to start the self-timer. Doing so prevents the camera from focusing on the subject. To cancel the self-timer after it starts, press the <^> button. When using the self-timer to take a picture of only yourself, first lock the focus (p.30) on an object at the same distance where you will be in the picture.

KWireless Remote Control

(DATE Model only)
With Remote Controller RC-5 (optional), wireless operation is possible up to 5 m/16.4 ft away from the front of the camera.
2 Take the picture. toward the Point the controller

If a picture is taken while the date and time are blinking, the date and time will not be imprinted on that picture. The date and time setting can be retained for about 10 min. after the cameras batteries are removed.
Selecting the AF mode..28 3Selecting the AF point..29 Focus Lock..30 When Autofocus Fails (Manual Focusing).31 HSelecting the Film Advance Mode..32 Metering Modes...32 T Program AE..33 R Shutter-Priority AE..35 E Aperture-Priority AE..36 W Manual Exposure...37 Q Automatic Depth-of-Field AE..38 Exposure Compensation..39 LAuto Exposure Bracketing (AEB).40 jAE Lock...41 <Multiple Exposures..42 Depth-of-Field preview..42 D Setting the ISO Film Speed..43 8Beeper Setting...43 7Safety Release Lock...44 Using the Built-in Flash..44 5Setting Custom Functions..47

Crea tiv

With Creative Zone modes, you can set the desired shutter speed or aperture value to obtain the exposure you want. You take control of the camera. A next to the page title indicates that the feature is available only in Creative Zone modes.

Selecting the AF mode

The AF mode is the AF operation method. Three AF modes are provided: ONE SHOT (One-Shot AF), AI FOCUS (AI Focus AF), and AI SERVO (AI Servo AF).

Select the AF mode.

turn the <l> dial.
Press the <4> button () and

ONE SHOT (One-Shot AF)

For still subjects. When you press the shutter button halfway, the AF focuses once.
s When focus is achieved, the AF point achieving focus flashes in red and the
focus confirmation light <n> in the viewfinder lights. The exposure is also set.

AI FOCUS (AI Focus AF)

This mode switches the AF mode automatically to One-Shot AF or AI Servo AF depending on whether the subject is still or moving.
Ideal for moving subjects whose distance from the camera keeps changing. The exposure is set at the moment the picture is taken.

AI SERVO (AI Servo AF)

For moving subjects. While you hold down the shutter button, the camera continues to focus the subject approaching or moving away from the camera.
Ideal for moving subjects whose distance from the camera keeps changing. The exposure is set at the moment the picture is taken. The beeper will not sound when focus is achieved.

3Selecting the AF point

The AF point is used for focusing. The AF point can be selected automatically by the camera or manually by you. In the Basic Zone modes and <Q> mode, the AF point selection is automatic only. In the <T> <R> <E> <W> modes, the AF point can be selected either automatically or manually. Automatic AF point Selection The camera selects the AF point automatically according to situation. Manual AF point Selection You can select any of the seven AF points manually. This is best when you want to be sure to focus on a particular subject, or to compose a particular shot quickly.

the <3> button. 1 Presscurrently-selected AF point will The

light.

2 Select the desired AF point.on the While looking at the AF point

Select with cross keys

Automatic selection Automatic selection Automatic selection

Automatic selection

LCD panel or in the viewfinder, press the cross keys to select the desired AF point. To select a horizontal AF point, press the left or right cross key. To select a vertical AF point, press the top or bottom cross key. You can also turn the <l> dial to select an AF point. If all the AF points light, automatic AF point selection will be set. Press the shutter button halfway to return to shooting.

Focus Lock

After achieving focus, you can lock the focus on a subject and recompose the shot. This is called focus lock.
1 Select the desired AF point. the 2 Focusthe AFsubject. the subject, point on Aim
then press the shutter button halfway.
3 Keep pressing the shutter button halfway and recompose

the picture as desired.

4 Take the picture.
If focus has not been achieved, the focus confirmation light <n> in the viewfinder will blink. In this case, you cannot take a picture even when you press the shutter button fully. Recompose the shot and focus again or see When Autofocus Fails (p.31). If you use an external, EOS-dedicated Speedlite and focus cannot be achieved with the AF-assist beam, select the center AF point. Focus lock also works in the Basic Zone modes (except <P>). Just start from step 2 above.
When Autofocus Fails (Manual Focusing)
Autofocus can fail to achieve focus (the focus confirmation light <n> blinks) with certain subjects such as the following:
Difficult Subjects for Autofocusing
Low-contrast subjects. Example: Blue sky, flat surface with a solid color. Subjects in very low light. Extremely backlit or reflective subjects. Example: Automobile with a strong reflection. Overlapping near and far objects. Example: Animal behind bars in a cage. Subjects having a repetitive pattern. Example: Personal computer keyboard, windows on a building, etc. In such cases, do one of the following: (1) Focus lock an object at the same distance as the subject and recompose. (2) Set the lens focus mode switch to <MF> and focus manually.

? Manual Focusing

the lens 1 Set<MF>. focus mode switch to subject. 2 Focus the turning the lens focusing Focus by
ring until the subject is in focus in the viewfinder.

Focus ring

If you hold down the shutter button halfway while focusing manually, the active AF point mark and the focus confirmation light <n> will light when focus is achieved.
HSelecting the Film Advance Mode
Two film advance modes are provided: single-frame and continuous shooting (Max. 3 frames per sec.).

Press the <^> button.

the <^> button.

J : Single frame:
A single picture will be taken when you press the shutter button all the way. H : Continuous shooting Continuous shots will be taken while you hold down the shutter button all the way. : Self-timer/Remote control

Metering Modes

The camera has three metering modes: Evaluative, partial, and center-weighted average metering.

Evaluative metering

This is the cameras standard metering mode suited for most shooting including backlit conditions. Based on the subjects position in the viewfinder, brightness, background, front or back lighting conditions, etc., the camera always calculates the proper exposure for the subject.

Partial metering

This mode is set automatically when AE lock is used in a Creative Zone mode. It is effective for backlit subjects when there is a strong light behind the subject. The viewfinder center covering about 9.5% of the viewfinder area is used for metering. The partial metering area is shown on the left.
Center-weighted average metering
This is set automatically in the <W> mode. The metering is weighted at the center and then averaged for the entire scene.

T Program AE

Like the <Y> (Full Auto) mode, this is a general-purpose mode to make picture-taking easy. It sets the shutter speed and aperture value automatically to suit the subjects brightness.
<T> stands for Program. AE stands for auto exposure.
1 Turn the Mode Dial to <T>.
AF point subject. 2 Focus the AF point over the subject Move the
and press the shutter button halfway.
the 3 Checkshutterdisplay.and aperture The speed
value are set automatically and displayed in the viewfinder and on the LCD panel. If the shutter speed and aperture value do not blink, a correct exposure will be obtained.
4 Take the picture. and press the Compose the shot
If and the maximum aperture value blink, it indicates underexposure. Use flash. If and the minimum aperture value blink, it indicates overexposure. Use an ND filter to reduce the light entering the lens.
The Difference Between <T> and <Y>

The shutter speed and aperture value are set in the same way in both modes. The following features can be used in the <T> mode, but not in the <Y> mode. Manual selection of AF mode and AF point Film advance mode selection Program shift Exposure compensation AEB Custom Function Depth-of-field preview AE/FE lock with the <j> button Multiple exposures Built-in flash manual firing and flash OFF High-speed sync (with EX-series Speedlites)

About Program Shift

In the Program AE mode, you can freely change the shutter speed and aperture value combination (program) set by the camera while retaining the same exposure. This is called program shift. To shift the program, press the shutter button halfway and turn the <l> dial until the desired shutter speed or aperture value is displayed. Program shift is canceled automatically after the picture is taken. Program shift cannot be set when the built-in flash is used.

R Shutter-Priority AE

In this mode, you set the shutter speed and the camera sets the aperture value automatically to suit the subject brightness. A fast shutter speed can freeze the motion of a fast-moving subject and a slow shutter speed can blur the subject to give the impression of motion.
<R> stands for Time value which is the shutter speed.
1 Turn the Mode Dial to <R>. 2 Select the desired shutter speed.

half-stop increments.

Turn the <l> dial. The shutter speed can be set in

Focus the subject.

aperture value is set automatically.
viewfinder 4 Check thethe picture. display and take
If the aperture value display is not
blinking, a correct exposure will be obtained.
If the maximum aperture value blinks, it indicates underexposure. Turn the <l> dial to set a slower shutter speed until the blinking stops. If the minimum aperture value blinks, it indicates overexposure. Turn the <l> dial to set a faster shutter speed until the blinking stops. Shutter Speed Display The shutter speeds from to indicate the denominator of the fractional shutter speed. For example, indicates 1/125 sec. Also, indicates 0.7 sec, and indicates 15 sec.

E Aperture-Priority AE

In this mode, you set the desired aperture value and the camera sets the shutter speed automatically to suit the subject brightness. The larger the aperture value (smaller aperture), the wider the depth of field (range of acceptable focus) will be. Vice versa, the smaller the aperture value (larger aperture), the narrower the depth of field will be.

<>> icon. 1 Move thethe LCDarrow to the <<> <\> button. () panel and press the Look at

will be displayed.

operation.
Set the desired number of multiple exposures.
Press the shutter button halfway to return to normal camera

s After

you take all the multiple exposures, the film advances to the next frame automatically and the multiple-exposure setting is canceled.
If you shoot multiple exposures on the first few or last few frames of a roll, the multiple exposures might not be precisely aligned due to the film curling. During multiple-exposure shooting, the <>> arrow next to the <<> icon on the LCD panel will blink. To cancel multiple exposures before shooting, set the number of multiple exposures to . To cancel multiple exposures after shooting, follow steps 1 and 2 to set the number of multiple exposures to blank.

Depth-of-Field preview

When you press the depth-of-field preview button, the camera will stop down the diaphragm to the current aperture. You can then see the range of acceptable focus in the viewfinder.
When you press the depth-of-field preview button, the exposure setting will be locked (AE lock).
D Setting the ISO Film Speed
If the film is not DX-coded or if you want to set a different film speed, load the film in the camera and set the film speed manually as follows. The settable film speed range is ISO 6 to 6400.
1 Move the <>> arrow to the <D> icon.
the <\> button to move the arrow. () s The current film speed is displayed.
desired speed. 2 Set thethe <l> filmto set the film dial Turn

speed.

The manually-set film speed will be canceled if the film is taken out and DX-coded film is loaded.

8Beeper Setting

the <>> 1 Move icon. arrow to the <8>
the setting / 2 Selectthe <l> dial to /select.the Turn
setting. 0 : Beeper silent. 1 : Beeper sounds when focus is achieved and during self-timer operation. 2 : Beeper sounds when focus is achieved, during self-timer operation, and during slow shutter speeds when camera shake can blur the shot. In this case, use a tripod.

7Safety Release Lock

This prevents shutter release if there is no film loaded or if there is no lens attached. It is particularly effective against missed shots due to no film. If you press the shutter button while there is no film in the camera or no lens attached, (F: film) or (L: lens) will blink in the viewfinder and on the LCD panel.

Move 1 <7> the <>> arrow to the icon.
While looking at the LCD panel,
press the <\> button. ()
. 2 Set it to <l> dial. Turn the
To cancel the setting, set it to

Using the Built-in Flash

With E-TTL II autoflash, high-precision and consistent flash exposures can be obtained.

In a Basic Zone Mode

In low-light or backlit conditions, the built-in flash will pop up and fire automatically (except in <I> <P> <S> modes).

In a Creative Zone Mode

Press the <M> button to pop up the built-in flash. T : Use this mode for automatic flash photography. The flash sync speed (1/60-1/125 sec.) and aperture value will be set automatically as with the <Y> (Full Auto) mode. R : Use this mode if you want to set the flash sync speed manually (within 30 sec. - 1/125 sec.). The camera will set the flash aperture value automatically to obtain a correct flash exposure.
E : Use this mode if you want to set the flash aperture value. The camera will set the flash sync speed (within 30 sec. 1/125 sec.) automatically to obtain the best exposure for the aperture you set. For portraits with a night scene or dark background, a slow sync speed will be set to obtain a proper exposure for both the subject and background. The flash illuminates the subject, while the background is properly exposed with a slow shutter speed. Because automatic slow-sync shooting uses a slow shutter speed, always use a tripod. If you do not want long exposures, set C.Fn-06. (p.48) W : You can manually set both the flash sync speed (within Bulb - 1/125 sec.) and aperture value. The subject is properly exposed with the flash and the background is exposed with the flash sync speed and aperture value you have set. Q : The result will be the same as using the <T> mode. Flash Distance Range (With EF28-90mm f/4-5.6) [m/ft] 28mm 90mm ISO Negative Film Slide Film Negative Film Slide Film - 4.6 / 3.3 - 15.- 3.3 / 3.3 - 10.- 3.3 / 3.3 - 10.- 2.3 / 3.3 - 7.1 - 9.2 / 3.3 - 30.4 1.2 - 6.6 / 3.9 - 21.- 6.6 / 3.3 - 21.- 4.6 / 3.3 - 15.2
When using the built-in flash, stay at least 1 meter/3.3 feet away from the subject. Otherwise, part of the photo will look dark. When using the built-in flash, detach any hood attached to the lens. A lens hood will partially obstruct the flash coverage. When a super telephoto lens or a fast, large-aperture lens is attached, the built-in flash coverage might be obstructed. The built-in flashs flash coverage is 28mm lens angle. To retract the built-in flash, push it down. This is a Type-A camera (compatible with E-TTL II autoflash) which can use all the features of EX-series Speedlites.

jFE Lock

FE (Flash Exposure) lock is for setting the correct flash exposure for any part of the subject. First pop-up the built-in flash.
the subject. 1 Focus pressing the shutter button Keep

until step 3.

the viewfinder center over 2 Aimtarget subject, then press the the <j> button.
preflash is fired and the <j> icon will be displayed in the viewfinder.
If the subject is beyond the effective flash range resulting in underexposure, the <M> icon will blink. Get closer to the subject and repeat steps 1 and 2. For the external Speedlite, use an EX-series Speedlite. If the camera is used with an EZ-, E-, EG-, ML-, or TL-series Speedlite, the flash will not fire in the TTL and A-TTL autoflash modes. Use the manual flash mode if the Speedlite has one. About E-TTL II Autoflash E-TTL II is a new autoflash exposure system incorporating improved flash exposure control and lens focusing distance information, making it more precise than the previous E-TTL (evaluative flash metering with preflash) system. The camera can execute E-TTL II autoflash with any EX-series Speedlite.
5Setting Custom Functions
You can customize camera functions to suit your preferences. They are called Custom Functions.
1 Display <5> on the LCD panel.
the icon. Function Setting No.
Press the <\> button to display
the Custom 2 Selectthe <l> dial.Function No. Turn the setting. 3 Changethe <[> button. The Press
Custom Function Setting No.
button toggles the setting between and . is the default setting. The <5> icon remains displayed on the LCD panel and the Custom Function setting is set.
Custom Function Settings C.Fn-01 Self-timer delay time
The 2-sec. delay is effective for preventing camera shake (when you press the shutter button) during close-ups and other critical work. 0 : 10-sec. delay 1 : 2-sec. delay
C.Fn-02 AF point selection method
0 : Press AF point selection button, then press the cross keys. 1 : Press the shutter button halfway, then press cross keys. Effective during the <> and <> active times. Pressing the <3> button switches to automatic AF point selection.

CANADA

EUROPE, AFRICA & MIDDLE EAST
CENTRAL & SOUTH AMERICA

OCEANIA

This Instruction booklet is current as of August 2004. For information on using the camera with system accessories introduced after this date, contact your nearest Canon Service Center.

CANON INC. 2004

PRINTED IN TAIWAN

> mode, use a tripod to prevent camera shake. In the <

> or

> mode, use a tripod if the shutter speed display blinks.

Page 26

Using Red-eye Reduction (with the built-in flash)
When flash is used in a low-light environment, the subjects eyes may come out red in the photograph. Red eye happens when the light from the flash reflects off the retina of the eyes. The cameras red-eye reduction feature turns on the red-eye reduction lamp to shine a gentle light into the subjects eyes to narrow the pupil diameter or iris. A smaller pupil reduces the chances of red eye from occurring. Red-eye reduction can be set in any shooting mode except < >, < > and < >.
the < > 1 Moveon the LCDarrow to the < icon panel.
Look at the LCD panel and press the
> button to move the arrow. ( )
the < > 2 TurnLCD panel. dial to set the
Press the shutter button halfway to
return to normal camera operation.
When red-eye reduction is enabled,
the red-eye reduction lamp-on indicator will be displayed in the viewfinder and on the LCD panel when you press the shutter button halfway. To cancel red-eye reduction, set on the LCD panel.
Red-eye reduction lamp-on indicator
Red-eye reduction will not work unless the subject looks at the red-eye reduction lamp. Tell the subject to look at the lamp. For maximum effectiveness, take the picture after the red-eye reduction lamp turns off (after 1.5 sec.). You can take a picture even while the red-eye reduction lamp is lit. The effectiveness of red-eye reduction varies depending on the subject. To further increase the effectiveness of red-eye reduction, go to a brighter environment or move closer to the subject.

Page 27

Using the Self-timer
The self-timer is useful when you want to be in the picture. It can be used in Basic Zone and Creative Zone modes. You should use a tripod.

1 Show the < panel.

Press the <

> icon on the LCD

> button to display the < > icon. To cancel the self-timer, press the < > button again or turn the Command Dial to < >.
2 Take the picture. procedure is the The picture-taking

same as with the < > Full Auto mode on page 22. Look through the viewfinder and press the shutter button fully to start the self-timer. When you press the shutter button fully, the beeper will sound and the picture will be taken 10 sec. later. During the first 8 sec., the beeper beeps slowly and the self-timer lamp blinks slowly. During the final 2 sec., the beeper beeps quickly and the self-timer lamp blinks quickly. Also, the self-timer display on the LCD panel counts down in seconds.
Do not stand in front of the camera when you start the self-timer. Doing so will throw off the focus. To cancel the self-timer after it starts, press the < > button again. When using the self-timer to take a picture of only yourself, first lock the focus (page 33) on an object at the same distance where you will be in the picture.

Page 28

Wireless Remote Control (DATE Model only)
With Remote Controller RC-1 (optional), wireless operation is possible up to 5 meters away from the front of the camera.

display the <

> button to > icon.
2 Take the picture. toward the Point the controller

Remote control sensor

cameras remote control sensor and press the transmit button. Display indications 2-sec. delay: The indicator will be the same as during the last 2 sec. of the self-timer. No delay: When the picture is taken, the self-timer/wireless remote control lamp will flash.
Certain types of fluorescent lights might cause the remote control operation to work improperly. Place the camera away from any fluorescent lights as far as possible. If you set the film advance mode lever to < > and do nothing for four minutes, the wireless remote control mode will be canceled automatically to save battery power.

Using the Eyepiece Cover

When you use the self-timer or wireless remote control and your eye does not cover the eyepiece, stray light entering the eyepiece may affect the exposure setting. To prevent this, attach the eyepiece cover to the eyepiece.
1 Remove the eyecup from the eyepiece.
Slip on 2 13) overthe Eyepiece cover (page the eyepiece. 28

Page 29

Imprinting the Date or Time (DATE Model only)
The camera has a date feature with an automatic calendar to 2099. It can imprint the date or time on the photograph as shown in the left photo. The imprinting can also be disabled so nothing is imprinted. The date or time can be imprinted in any shooting mode.
The date or time is imprinted on the lower right corner of the photograph.

1 Move the <

> arrow to <
( ) Look at the LCD panel and press the < > button. If the date and time has not been set, will blink on the LCD panel. See page 30 to set the date and time.
the 2 Selectthe < date format. > dial. Turn
The date format will change in the following loop:

Year, month, day

Month, day, year

Day, month, year

Day, hour, minute

Page 30

Setting the Date and Time
< > 1 Move thethe LCDarrow to < press>. panel and the Look at
< > button. If the date and time has not been set, will blink on the LCD panel.
digit be set. 2 Select the < >tobutton. Press the
The digit selection will change in the
following sequence: year, month, day, hour, minute, .
3 Set the correct> number. dial. Turn the <
Repeat steps 2 and 3 until all the
date and time digits are set correctly.
4 Finalize the date and time setting. Keep pressing the < > button until

no digits are blinking.

If you press the <
> button while is blinking, 0 sec. will be set.
If a picture is taken while the date and time are blinking, the date and time will not be imprinted on that picture. The date and time setting can be retained for about 10 min. after the cameras batteries are removed.

NNN E SEC3 (31-51)

02.5.11 11:16 AM

Page 31

User-Controlled Shooting
Selecting an AF point..32 Focusing Off-Center Subjects..33 When Autofocus Fails..34 Selecting the Film Advance Mode..35 Metering Modes..35 : Program AE..36 : Shutter-Priority AE..38 : Aperture-Priority AE..40 Depth-of-field Preview..41 : Manual Exposure...42 : Automatic Depth-of-Field AE..43 AE Lock..44 : Exposure Compensation..45 Auto Exposure Bracketing (AEB).46 Bulb Exposures..47 Multiple Exposures..48 Using the Built-in Flash..49 : Setting the ISO Film Speed..50 Silencing the Beeper...51 LCD Panel Illumination..51 Using the Remote Switch..51

Cre ati v

The Creative Zone modes enables you to set any shutter speed and aperture to obtain the exposure or effect you want. You can set the AF point, film advance mode, AE lock, exposure compensation, AEB, multiple exposures, and depth-of-field preview.

Page 32

Selecting an AF point
The AF point is used for focusing. The AF point can be selected automatically by the camera or manually by you. In the Basic Zone modes and < > mode, the AF point selection is automatic only. In the < >, < >, < >, and < > modes, the AF point can be selected either automatically or manually.
Automatic AF point Selection
The camera selects the AF point automatically according to situation.
Manual AF point Selection
You can select any of the seven AF points manually. This is best when you want to be sure to focus on a particular subject, or to use the time of the AF function to help you compose a particular shot quickly.
the < ( 1 Presscurrent AF > button.light. ) The point will
2 Select the desired AF point. on the While looking at the AF points
LCD panel or in the viewfinder, turn the < > dial to select the desired AF point. The selected AF point will flash in the viewfinder. The AF point selection will change in the looping sequence below. After selecting the AF point, press the shutter button halfway. The camera will then be ready to take pictures.
Automatic AF Point Selection Manual AF Point Selection

Page 33

Focusing Off-Center Subjects
If you want to focus an off-center subject not covered by any of the AF points, use focus lock as described below.
1 Select the desired AF point. (page 32) the 2 Focusthe AFsubject. the subject, then point on Aim
press the shutter button halfway.
3 Keep pressing the shutter button halfway and recompose the

picture as desired.

4 Take the picture.
Focus lock also works in the Basic Zone modes (except< from step 2 above.

>). Just start

Page 34

When Autofocus Fails

The camera has a high-precision AF system which can focus almost all subjects. However, it can fail to achieve focus (the focus confirmation light < > blinks) the subjects listed below.
Difficult Subjects for Autofocusing
Low-contrast subjects. Example: Blue sky, flat surface with a solid color. Subjects in very low light. Extremely backlit or reflective subjects. Example: Automobile with a strong reflection. Overlapping near and far objects. Example: Animal behind bars in a cage. In such cases, use one of the following methods to focus: (1) Focus lock an object at the same distance as the subject and recompose. (2) Set the lens focus mode switch to <MF> or <M> and focus manually as explained below.
If focus cannot be achieved even with the EOS-dedicated Speedlites AF-assist light, select the center AF point.

:Aperture-Priority AE
In this mode, you set the aperture and the camera sets the shutter speed automatically to suit the brightness of the subject. A large aperture (lower f/number) will blur the background and make the subject stand out. The larger the aperture, the more blurred the background will look. Or, a smaller aperture (higher f/number) will increase the depth of field to make both the foreground and background look sharp. The smaller the aperture, the sharper the background will look. Av stands for aperture value.
Taken with a large aperture.
Taken with a small aperture.
the 2 Selectat thedesired aperture. the LCD panel and turn Look
< > dial to set the desired aperture.
The shutter speed is set automatically.

Page 41

If the shutter speed display does not
blink, a correct exposure will be obtained.
If the slowest shutter speed blinks, it indicates underexposure. In such a case, turn the < > dial to set a larger aperture (smaller f/number) until the shutter speed display stops blinking. If the fastest shutter speed blinks, it indicates overexposure. In such a case, turn the < > dial to set a smaller aperture (larger f/number) until the shutter speed display stops blinking. Aperture Display The aperture can be set and displayed in full and half stops as shown below. The larger the number, the smaller the aperture opening will be. The displayable range of apertures depends on the lens mounted on the camera.

Depth-of-field Preview

To check the depth of field, press the depth-of-field preview button. The camera will stop down the aperture and you can check the in-focus range in the viewfinder.
This feature works in Creative Zone modes. When you press the depth-of-field preview button, AE lock also takes effect. In the < > mode, press the shutter button halfway to focus, then keep pressing the shutter button halfway and press the depth-of-field preview button.

Page 42

:Manual Exposure
In this mode, you set both the shutter speed and the aperture for total exposure control. The exposure level of the shutter speed and aperture you set is indicated on the exposure level scale. You can thereby check how suitable the exposure will be. In the < > mode, the centerweighted average metering will be set automatically. M stands for Manual.
1 Turn the Command Dial to < >. shutter speed and aperture. 2 Set the the shutter speed, turn the To set
< < dial. > dial. > button and turn the < >
To set the aperture, hold down the
The exposure level will be displayed in the viewfinder and on the LCD panel. The exposure level indicator < > indicates how close the exposure level is to the correct exposure.
4 Set theatdesired exposure.indicator Look the exposure level

and set the shutter speed and aperture as desired. If the exposure level indicator < > blinks at < > or < >, it indicates that the exposure is respectively overexposed or underexposed by 2 stops or more.
Correct exposure Over exposure Under exposure
: This is the standard level for a correct exposure. : To achieve the correct exposure, set a faster shutter speed or a smaller aperture. : To achieve the correct exposure, set a slower shutter speed or a larger aperture.

Page 43

:Automatic Depth-of-Field AE
This mode is for obtaining a wide depth of field automatically between a near subject and far subject. It is effective for group photos and landscapes. The camera uses the 7 AF points to detect the nearest and farthest subjects to be in focus. A-DEP stands for Auto-depth of field.
the subject. 2 Focus the AF point over the subject Move
and press the shutter button halfway.
All the subjects covered by the AF
points which flashed in red will be in focus. If you press the depth-of-field preview button while the exposure reading is displayed in the viewfinder, you can see the depth of field. (page 41)
3 Check the viewfinder display and take the picture.
In the example above, the focus will
be sharp between the front person on the left and the rear person on the right.
The < > mode cannot be used if the lens focus mode switch is set to <MF> (or <M> on older lenses). If the aperture blinks, it indicates that the exposure level is correct but the desired depth of field cannot be achieved. Either use a wide-angle lens or move further away from the subjects. In this shooting mode, you cannot freely change the shutter speed and aperture. If the camera sets a slow shutter speed, hold the camera steady or use a tripod. If flash is used, the result will be the same as using flash in the < > mode.

Page 44

AE Lock
With the same AF point, you can obtain and lock the auto exposure setting on one part of the picture and then recompose to focus a different part of the picture. AE lock enables you to maintain the same exposure setting even after recomposing the shot. This is effective for backlit subjects. During AE lock, partial metering (page 35) is used automatically.

subject. 1 Focus the shutter button halfway to Press the
focus. ( ) Proceed to steps 2 and 3 holding the shutter button halfway down.
2 Aim the viewfinder center over the part where you want to lock the
exposure, then press the < button. ( ) >
The < > indicator lights in the viewfinder and the exposure setting locks (AE lock). The auto exposure locks every time you press the < > button.
3 Compose the shot and take the picture.
If you want to maintain the AE lock
while taking more pictures, hold down the < > button and press the shutter button to take another picture.

Page 45

:Exposure Compensation
Changing the exposure level set by the camera is called exposure compensation. Exposure compensation can be used to make the picture darker or brighter intentionally. Exposure compensation can be set up to +/2 stops in half-stop increments.
1 Turn the Command Dial to a< >. Creative Zone mode except halfway 2 Press the shutter button display. and check the exposure 3 Press and hold down the><dial until> button and turn the <
the desired exposure compensation amount is set. ( )

The <

Increased exposure amount
> side of the scale indicates increased exposure, and the < > side of the scale indicates decreased exposure.
Decreased exposure amount Increased exposure amount
The exposure compensation amount
Decreased exposure amount
set is retained even after the Command Dial is set to < >. To cancel the exposure compensation, set the exposure level indicator back to < >.
The exposure compensation amount is canceled automatically when you turn the Command Dial to a Basic Zone mode. Assuming that a shutter speed of 1/125 sec. and an aperture of f/5.6 will give a correct exposure, setting the exposure compensation amount to plus or minus 1 stop will change the shutter speed or aperture as follows: Shutter Speed Aperture 1 stop 250 8.0 5.6 +1 stop 60 4.0

Page 46

Auto Exposure Bracketing (AEB)
With AEB, the camera automatically changes the exposure within the set range (up to +/2 stops in 1/2-stop increments) for three successive frames.

If you shoot multiple exposures on the first few or last few frames of a roll, the multiple exposures might not be precisely aligned due to the film curling. During multiple-exposure shooting, the < > arrow next to the < > icon on the LCD panel will blink. To cancel multiple exposures before shooting, set the number of multiple exposures to 1. To cancel multiple exposures after shooting, follow steps 1 and 2 to set the number of multiple exposures to blank.

Page 49

Using the Built-in Flash

In a Basic Zone Mode

In a Basic Zone mode (except < >, < > and < >), the built-in flash will pop up and fire automatically in low-light or backlit conditions.

In a Creative Zone Mode

When using a Creative Zone mode, press the < built-in flash.
> button to pop up the
: Use this mode for automatic flash photography. The flash sync speed and flash aperture will be set automatically as with the < > (Full Auto) mode. : Use this mode if you want to set a flash sync speed slower than 1/90 sec. The camera will set the flash aperture automatically to obtain a correct flash exposure. : Use this mode if you want to set the flash aperture. In this mode, you can obtain a balanced exposure between the subject and a dark background (night scene, etc.) with a slow sync speed set automatically by the camera. The flash illuminates the subject while the background is exposed with a long shutter speed. : This mode enables you to set both the flash sync speed and flash aperture. The subject is properly exposed with the flash and the background is exposed with the flash sync speed and aperture you have set. : The result will be the same as using the < > mode.
Flash Sync Speeds and Flash Apertures
Mode Sync Speed The sync speed is set automatically to 1/90 sec. Flash Aperture The flash aperture is set automatically according to the TTL program.
Any sync speed 1/90 sec. or slow- The flash aperture is set automaticaler can be set manually.* ly to match the sync speed you set. The sync speed is set automatically within a range of 30" to 1/90 sec. to match the flash aperture you set. Any sync speed 1/90 sec. or slower can be set manually.* * If the sync speed is set faster than 1/90 sec., it will be reset automatically to 1/90 sec.
You set the flash aperture manually.

Page 50

Flash Distance Range (With EF 28-90mm f/4-5.6)
ISO 28mm Negative Film Slide Film 1 - 3.0 / 3.3 - 9.8 90mm Negative Film 1 - 3.0 / 3.3 - 9.8 Slide Film 1 - 2.1 / 3.3 - 6.- 4.3 / 3.3 - 14.1
100 m / ft 1 - 4.2 / 3.3 - 13.1
400 m / ft 1 - 8.5 / 3.3 - 27.9 1.2 - 6.0 / 3.9 - 29.- 6.0 / 3.3 - 19.7
When using the built-in flash, stay at least 1 meter/3.3 feet away from the subject. Otherwise, part of the photo will look dark. When using the built-in flash, detach any hood attached to the lens. A lens hood will partially obstruct the flash coverage. When a super telephoto lens or a fast, large-aperture lens is attached, the built-in flash coverage might be obstructed. To retract the built-in flash, push it down. The built-in flashs flash coverage is 28mm lens angle. If more light is required, use an external, EOS-dedicated Speedlite (optional).

Depth of field

This is the range where acceptable focus can be achieved in front of and behind the point of optimum focus. The smaller the aperture (the larger the f/number), the deeper the depth of field. And the larger the aperture (the smaller the f/number), the shallower the depth of field.

(page 40)

Page 53

Exposure Warning List

Mode Blinking Warning Indication The subject is too dark. The subject is too bright. The picture will be underexposed. The picture will be overexposed. The picture will be underexposed. The picture will be overexposed. Countermeasures Use flash.
Attach a neutral density filter to the lens. Turn the < > dial to set a slower shutter speed. Turn the < > dial to set a faster shutter speed. Turn the < > dial to set a larger aperture (smaller f/number). Turn the < > dial to set a smaller aperture (larger f/number).
1) Move away from the subject and try again. The desired depth of 2) If a zoom lens is used, field cannot be use the shortest focal obtained. length. The subject is too dark. The subject is too bright. Use flash. The result will be the same as using the < > mode. Attach a neutral density (ND) filter to the lens.
The sample warnings above apply when the lens used has a maximum aperture of f/4.0 and minimum aperture of f/22. The maximum and minimum aperture warning displays will differ depending on the lens attached to the camera.

Page 54

Feature Availability Table
Command Dial Mode One-Shot AI Servo AF Built-in Flash Metering Mode Film Advance Functions AI Focus Auto AF Point Selection Manual AF-Assist beam Single frame Continuous
Self-timer/Remote control
Evaluative Partial Centerweighted avg. Auto Firing Always Firing
Program shift Exposure Compensation AE Lock Depth-of-field preview Date ISO Speed Red-eye Reduction Beeper Multiple Exposures AEB
: Set automatically. ( ): Set automatically during AE lock. : User-selectable/settable.

Page 55

AF Mode

One-Shot AF

When focus is achieved, the exposure setting is set simultaneously and the focus is locked. The shutter cannot be released until focus is achieved.

AI Servo AF

Ideal for moving subjects. The moving subject is focused continuously while the camera predicts the subject's point of focus for when the shutter is released. The exposure is set when the shutter is released.

AI Focus AF

When you press the shutter button, the AF mode (One-Shot AF or AI Servo AF) is set automatically depending on whether the subject is moving or not.

AF Mode and Film Advance Mode
Film Advance Mode One-Shot AF The picture cannot be taken until focus is achieved. When focus is achieved, it also locks at the same time. The evaluative meterings exposure reading is also locked. (The exposure setting is retained until the picture is taken.) The same conditions as above apply during continuous shooting (at about 2.5 frame per second). AI Servo AF

Single frame

Autofocusing continues to match the subjects movement. The exposure setting is determined at the moment of exposure.

Continuous

The same conditions above apply during continuous shooting. Autofocusing continues during continuous shooting (at about 2.3 frame per second).

Page 56

Troubleshooting Guide
If there is a problem, try to resolve it by referring to this Troubleshooting Guide. If the problem still persists, take the camera to your nearest Canon Service Center. Nothing is displayed on the LCD panel. The picture looks blurred. The batteries are exhausted. Replace the batteries with new ones. (page 14) The batteries have been installed incorrectly. Install the batteries correctly. (page 14) The lens focus mode is set to <MF> (or <M>). Set the lens focus mode to <AF>. (page 16) There was camera shake when the picture was taken. Hold the camera steady or use a faster shutter speed. (page 17) The frame count is not displayed on the LCD panel. The shutter Take out the film and load it correctly. (page 18) does not work. The < > icon blinks on the LCD panel. Replace the batteries with new ones. (page 14) The < > icon blinks while the rewound film is still in the camera. Replace with a new roll of film. (page 18) The focus confirmation light < > in the viewfinder blinks and focus cannot be achieved. Select another AF point. (page 32) If focus still cannot be achieved, focus manually. (page 34) The battery level is very low. The < > icon blinks on Replace the batteries with new ones. (page 14) the LCD panel. A misoperation has occurred. Press the shutter button halfway. (page 17) Remove the batteries and reload it. (page 14) If the blinking < > icon does not turn off, consult your nearest Canon Service Center.
When using an external flash unit, an EOS-dedicated Speedlite is recommended. Using the camera with a flash unit (equipped with electrical contacts on the hot shoe foot), high-voltage flash unit, or flash accessories dedicated to a different brand may result in camera misoperation or malfunction.

Page 57

Major Specifications
Type..35 mm AF/AE SLR camera with built-in winder and flash Recording media.35 mm film Image size..24 x 36 mm Compatible lenses..Canon EF lenses Lens mount..Canon EF mount (electronic data exchange)

Viewfinder

Type..Eye-level pentamirror Coverage.90% vertically and horizontally Magnification..0.7x (1 diopter with 50mm lens at infinity) Eyepoint..18.5 mm Dioptric adjustment range..2.5 - +0.5 diopter Focusing screen..Fixed (New Laser Matte screen) Mirror..Quick-return half mirror (Transmission: reflection rate of 40:60, No mirror cut-off with EF 300mm f/2.8L plus Extender 2x or shorter lens) Viewfinder information.AF (superimposed AF point, focus confirmation light); Exposure (shutter speed, aperture, exposure level, exposure warning, AE lock); Flash (flash ready, hi-speed sync, FE lock, red-eye reduction, out of working range warning) Depth-of-field preview.Depth-of-field preview button

Date imprinting (DATE Model only) Automatic dating.Automatic calender to 2099 Power source.Uses camera power Power source
Power source..Two CR2 lithium batteries Battery life.. (page 15) Battery check..Automatic

Dimensions

(W x H x D).130 x 88 x 64 mm/5.1 x 3.5 x 2.5 in Weight..365 g/12.9 oz (body only, excluding batteries)
All the specifications above are based on Canon's testing and measuring standards. Specifications and physical appearance are subject to change without notice.

Page 59

AEB...46 AE lock..44 AF...16 AF-assist beam...23 AF mode..55 AF point..32 AI Focus AF...55 AI Servo AF...55 Aperture...52 Basic Zone..12, 21 Batteries..14 Beeper..51 Built-in flash...49 Bulb exposures...47 Command Dial..12 Continuous shooting..35 Creative Zone..12, 31 Date/time...29 Depth- of- field AE..41, 52 Dioptric adjustment..9 Eyepiece cover..28 Exposure...52 Exposure compensation..45 Feature Availability Table.54 Film loading...18

O P R S

unloading..19 midroll rewind..20 setting ISO speed manually.50 ISO speed..52 Flash..23 Focus lock..33 Full Auto mode..22 Holding the camera..20 LCD panel..10 illumination..51 Lens mounting / detaching..16 Manual focusing..34 Metering modes..35 Multiple exposures.48 One-Shot AF..55 Program AE...36 Programmed Image Control Modes..24 Red-eye reduction..26 Remote switch..51 Self-timer...27 Shutter button..17 pressing halfway.17 pressing fully...17 Shutter speed..52 Single-frame shooting.35 Superimpose..11 Viewfinder information..11 Wireless remote control..28
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Consult the dealer or an experienced radio/TV technician for help. This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled Digital Apparatus, ICES-003 of the Industry Canada.

The CE Mark is a Directive conformity mark of the European Community (EC)
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
U.S.A. CANON U.S.A. INC. For all inquiries concerning this camera, call toll free in the U.S. 1-800-OK-CANON or write to: Customer Relations, Canon U.S.A., Inc. One Canon Plaza, Lake Success, N.Y. 11042-1198 CANON CANADA INC. HEADQUARTERS 6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada CANON CANADA INC. MONTREAL BRANCH 5990, Cte-de-Liesse, Montral Qubec H4T 1V7, Canada CANON CANADA INC. CALGARY OFFICE 2828, 16th Street, N.E. Calgary, Alberta T2E 7K7, Canada For all inquiries concerning this camera, call toll free in Canada 1-800-OK-CANON CANON EUROPA N.V. Bovenkerkerweg 59-61, P.O. Box 2262, 1180 EG Amstelveen, The Netherlands CANON COMMUNICATION & IMAGE FRANCE S.A. 102, Avenue du Gnral de Gaulle 92257 La Garenne-Colombes Cedex, France CANON UK LTD. Woodhatch Reigate Surrey RH2 8BF, United Kingdom CANON DEUTSCHLAND GmbH Europark Fichtenhain A10, 47807 Krefeld, Germany CANON ITALIA S.p.A. Palazzo L, Strada 6, 20089 Rozzano, Milanofiori, Milano, Italy CANON Benelux N.V./S.A. Bessenveldstraat 7, 1831 Diegem (Machelen), Belgium CANON Schweiz AG Geschftsbereich Wiederverkauf, Industriestrasse 12, CH-8305 Dietlikon, Switzerland CANON G. m. b. H. Oberlaaerstrasse 233, 4th floor, 1100 Wien, Austria CANON Espaa, S. A. C/Joaqun Costa, 41, 28002 Madrid, Spain SEQUE Soc. Nac. de Equip., Lda., Praa da Alegria, 58, 2, 1269-149 Lisboa, Portugal CANON LATIN AMERICA, INC. DEPTO DE VENTAS 703 Waterford Way Suite 400 Miami, FL 33126 U.S.A. CANON LATIN AMERICA, INC. CENTRO DE SERVICIO Y REPARACION Apartado 2019, Zona Libre de Coln, Repblica de Panam CANON HONGKONG CO., LTD. 9/F, The Hong Kong Club Building, 3A Chater Road, Central, Hong Kong CANON SINGAPORE PTE. LTD. 79 Anson Road #09-01/06 Singapore 079906 CANON AUSTRALIA PTY. LTD. 1 Thomas Holt Drive, North Ryde, N.S.W. 2113, Australia CANON NEW ZEALAND LTD. Fred Thomas Drive, P.O. Box 33-336, Takapuna, Auckland, New Zealand CANON SALES CO., INC. 12-15 Mita, 3-Chome, Minato-ku, Tokyo 108-8011, Japan

CANADA

EUROPE, AFRICA & MIDDLE EAST
CENTRAL & SOUTH AMERICA

OCEANIA

This Instructions booklet is current as of April 2002. For information on using the camera with system accessories introduced after this date, contact your nearest Canon Service Center.

CT1-1236-000

CANON INC. 2002

PRINTED IN TAIWAN