IMPORTANT STAND AND BASE SAFETY INFORMATION
Choose the location for your TV carefully. Place the TV on a stand or base that is of adequate size and strength to prevent the TV from being accidentally tipped over, pushed off, or pulled off. This could cause personal injury and/or damage the TV. Refer to the Important Safety Instructions above.

FCC Warning

Class B Computing Device Information to User This equipment has been tested and found to comply with the limits for a Class B Digital Device pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wilt not occur in a particular installation. If this equipment receives interference while off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and TV. 3) Connect the equipment into an outlet on a circuit different from that to which the TV is connected. 4) Consult the dealer or an experienced radio/TV technician for help and for additional suggestions. The user may find the following booklet prepared by the Federal Communications Commission helpful: "How to Identify and Resolve Radio - TV Interference Problems". This booklet is available from the US Government Printing Office. Washington, D.C. 20402, Stock No. 004-000-00345-4.
The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. NOTE: In order for an installation of the product to maintain compliance with the limits for a Class B Device, shielded cables must be used.

Manual TABLE OF CONTENTS

INTRODUCTION Safety Precautions Specifications Feature Descriptions Front and Rear Unit Profiles Remote Control Features INSTALLATION Connecting the Antenna Installing the Remote Control Batteries.... Connecting A/V Equipment.... Input from Device to TV Output from TV to Device FUNCTIONS & FEATURES Turn On/Off Basic Functions.... Function Selection Menus Useful Remote Control Features ADDITIONAL Programming FEATURES the Remote Control GUIDE 23 SPECIFICATIONS MODEL

FEATURES 181 Channel Tuner AV Input (Rear) AV Input (Side) S-Video Input DVD Input (Rear) AV Output (Rear) Screen Size Pure Flat CRT Universal Remote Control Auto Program Channel Recall Closed Caption Parental Control Picture Modes Trilingual OSD Sound Modes MTS Stereo/AV Stereo Favorite Channel Channel Label Full On/Off Timer Sleep Off/Auto Off without Signal in TV Mode AVC (Automatic Volume Control) 3 Lines Comb Filter VSM Color Temp Control X-Ray Protection Blue Back On/Off Digital Geometric Correction Child Lock Black Level Stretch Automatic White Balance Adjustment

PF2020. 1 20"....

1 20"

1 27"

1 32"
Front and Rear Unit Profiles Front panel PF2020/PF2030

A_------X

IV IN( ;: VIDEO
STANDBY INFRARED SENSOR POWER LED

L/MIINO

MENUELECT S TV/VlI}EI1SELECT VlILUME DIIWN/UP CHANNELDBWN/UP

AUDI[ L

VOL -t-

CH -4-

Rear panel

1 BUT VIDEO

DVD IN AVIIN(2>

-- R_----LIMBNB=

IN(I>-. S-VIDEFI

(continued)

Front and Rear Unit Profiles Front panel PF2720/3220

AVIN(4) VIDEO

_AUDIO_

A LmONO

MENUELECT S TV/VIDEBSELECT VBLUME DBWN/UP CHANNELDI]WN/UP

CH -t-

-AV 0_]
Front and Rear Unit Profiles Front panel PF2730/3230

i i i i i i

;-_E0(<

_AUDIO

VIDEO MENU -VOL -t-CH -t-

L/MONO

Av (4) IN
MENUSELECT TVIVII)EFI SELECT VilLUMEIIVNIUP CHANNELDIIWNIUP D

-AVIN(3

-AVliNT

0 VIDE_

L/MIINII Cb

I Remote

Features

Control

Led Set
Indicator light Used for control programming the remote d Cycles through the Video/TV modes Selects the various Picture Modes Used to navigate the TV menus Used to change the current channel Brings up the TV/Video display Used for child lock Selects the MTS Stereo modes among Mono, Stereo and SAP Activates Closed Captioning Switches the TV between Normal modes Sets favorite channels Turns on/off the TV Used to select channels by number Wide and d KEYPAD STANDBY
Video Picture Arrows CH +/Display Function MTS/SAP

CC Full

Favorite Standby Keypad
TV, DVD/VCR, SAT/CAB, AUX switch Determines the equipment by the remote Menu Sound Enter Accesses the main menu

controlled

MTSISAP
SCAN RECALL RECALL t SCAN LABEL

RITE _

Selects the various Sound modes Confirms menus selections or accesses sub
VOL + / Sleep Mute Recall Scan Label
Used to adjust the volume level Activates/Deactivates the sleep timer

CK5D-C1

Mutes or restores the TV volume Returns to the last channel viewed Scans all active channels Used to label channels

INSTALLATION

Please read the safety instructions in this manual completely before installation. Install your TV in an area where direct sunlight will not fall upon the screen. Soft, indirect light is best for television viewing. Allow enough space (at least 4 in.) between the TV and any walls or enclosures for proper ventilation. Optimum television viewing distance is 3-5 times the screen's size.

Auto-Deqaussinq

Color television can be easily affected by magnetism, which shows as color distortion on the screen. If your TV is affected by nearby magnetic components or appliances, turn it off for a few minutes. The built-in auto-degaussing circuit will eliminate the magnetic interference.

I Connecting

the Antenna

VHF UHF or Cable

75-ohm coaxial cable (not supplied)
300-ohm twin-lead cable (n_

Li VHF

/_(nte_ adapter _ Xnna

(not supplied)

RF Input (back of TV unit)

Notes:

1. It is recommended that a 75 ohm coaxial cable be used in order to
eliminate interference and noise which may occur due to nearby radio transmissions. 2. The antenna cable should not be tied together with other wiring. 3. Set up a lightning rod and check it regularly when an outdoor antenna is used.

I Installing

the Remote

Batteries

1. Remove the battery compartment
2. Insert two AAA batteries (included). Make sure the positive (+) and negative (-) polarities are correctly aligned. 3. Reattach the battery lid.
1. Alkaline batteries are recommended for longer life. 2. Always replace both batteries at the same time. 3. Do not expose batteries to fire or break them open. 4. To avoid battery leakage, remove batteries from the remote control when it is not being used for a long period of time. 5. If the remote control can't control the TV properly after new batteries installed, remove the batteries from the remote control and hold down the F key for over 5 seconds. Insert the batteries and try again.
PF2020-PF3230 _ 2003.5.8 J_

.(continued)

I PF2020/PF2030

Connecting

AN Equipment
The following are diagrams showing basic instructionsfor attaching external equipment, like a VCR or DVD player, to your TV set. Please refer to operation manuals of external audio/video equipment that will be connected to your set for additional instructions. PLEASE TURN OFF ALL POWER BEFORE CONNECTING DEVICES TOGETHER.
Connect VCR's RF OUT terminal to the RF IN jack located on the rear panel of the TV.

Coaxial Cable

I Input from Device to TV 1
DO NOT use the DVD IN terminals and AV IN (2) terminals at the same time. DO NOT connect side AV IN(1),rear AV IN(l) and S-Video terminals at the same time. Use only one of the three. With DVD signal input, there is no DVD video output. Also, remember to connect the audio cables when using S-Video and DVD terminals.

AUDIONIDEO IN

DVD Player With S - VIDEO Terminal

_VIN(I:

VlDED @ Camcorder VIDEO _8Z33=

_UDIEL

L/MBNI]
I Output from TV to Device

AUDIONIDEO OUT

@ AUDIO

@ _AUDIDQ

VIDEII

1 rlUT

The side terminals may be easier to use with a camcorder. The connections

are identical.

PF2020 _ 2003.7.31

(continued) ]

PF2720/PF3220

INSTALLATION Connecting

AN Equipment (continued)
The following are diagrams showing basic instructionsfor attaching external equipment, like a VCR or DVD player, to your TV set. Please refer to operation manuals of external audio/video equipment that will be connected to your set for
additional instructions. PLEASE TURN OFF ALL POWER BEFORE CONNECTING

DEVICES TOGETHER.

I Input from Device to TV I
AUDIONIDEO IN DO NOT connect input, there S-Video

OoaxaOa e

DO NOT use the DVD IN terminals and AV IN(3) terminals terminal. at the same time. both AV IN(l) and S-Video Use only one of the two. With DVD signal to connect the audio cables when using is no DVD video output. Also, remember

and DVD terminals.

DVD Player

With S - VIDEO Terminal

Av N _ (4)

@ Camcorder

FAIJDIO_

L/MO_o

AUDIONIDEO OUT @

VIDEO @

The side terminals may be easier to use with a camcorder.

The connections

PF2020 _ 2003.7.31 )_

PF2730/3230

NV Equipment (continued)
Connect VCR's RF OUT terminal to the RF IN jack located on the rear panel of the TV. 21_ C) _1 Coaxial Cable RF IN
DO NOT use the DVD IN terminals DO NOT connect both AV IN(l) and AV IN(3) terminals terminal.

AUDIONIDEO

at the same time. Use only one of the two. DO NOT using S-Video and DVD
and S-VIDEO(I) terminals to connect
use the AV IN(4) and S-VIDEO(4) DVD video output. Also, remember terminals. DVD Player
at the same time. With DVD signal input, there is no the audio cables when
With S - VIDEO Terminal _, wEo(4

_AL_IO -

Camcorder

--RAW(4)

L/_o_o

}Output

from TV to Device I

VIDEO @ @

-AV UUT

FUNCTIONS

1. Turn On

& FEATURES

Turn On/Off 1
Plug in the supply cord, and the TV should enter the Standby mode. Pressing the STANDBY on the remote control or on the TV can turn on the TV. Also, the power indicator light on the TV will come on. 2. Standby (Soft Off) While the TV is on, press the STANDBY key. This will put the TV in Standby or soft off mode. The power indicator light on the TV set will turn off. 3. Auto off when no signal received The TV set will automatically enter into Standby mode when the following conditions are met. 1) TV is in antenna mode. 2) Current channel has no signal. 3) No key is pressed within 15 minutes.

I Basic Functions

Changing the Channel
While in Tuner mode, press the CH +/- keys to change the channel, or use the numeric keypad to enter a new channel.

Adjusting

the Volume
To increase or decrease the volume, press the VOL +/- keys. The volume adjustment ranges from 0 to 100.

Muting the Volume

To mute the volume, press the MUTE key. To restore the volume, press MUTE again.
[ Function Selection Menus J
All Function menus can be accessed by pressingthe MENU key on the remote control or the top panel. Navigationof the menu be done withthe arrowsand ENTER keys on the remoteand- CH + and - VOL + keys on the top panel. Exitwith the MENU key.

Video Setting

This menu allows you to adjust the various picture settings. Access From the Main menu screen, press the left or right arrow key until Video Setting is highlighted. Then the Video Setting menu is displayed. Press the up or down arrow key to select Picture Contro/and right arrow key or ENTER key to access the sub menu. Use the up or down arrow key to move between the various settings, and the left or right arrow key to adjust them. CONTRAST: 0 (minimum contrast) to 100 (maximum contrast) BRIGHTNESS: 0 (dimmest) to 100 (brightest) COLOR: 0 (minimum color) to 100 (maximum color) SHARPNESS: 0 (minimum sharpness) to 100 (maximum sharpness) TINT: -50 (more purplish) to +50 (more greenish) COLOR TEMP: Cool, Standard or Warm Video Setting Picture Mode Picture Control Auto Black Lvl VSM Normal _, On On

Picture Control:

I Move:_

Enter:|

Exit :_EN0-]I
Picture Mode: Use the left or right arrow key to select among
User, Normal, Movie and Sports.
Auto Black Lvh This feature improves gradation of picture. Press the left or right arrow key to set it On or Off after Auto B/ack Lv/is highlighted. VSM: This feature allows you to improve sharpness. Press the left
or right arrow key to set it On or Off after VSM is highlighted. Note:
Picture Control Contrast Brightness Color Sharpness Tint Color Temp

10 Warm

Move: f _

ADJ: *--*

Exit:[ME_7
This function is not available for PF2020, PF2720 and PF3220. For PF2030, PF2730 and PF3230, it doesn't work in the DVD mode.

PF2020-Pf3230

2003.5.8
& FEATURES (continued)
I Function Selection Menus (continued) I

Audio Setting Menu

Audio Setting Sound Mode Sound Control Surround AVC User Off Off
This menu allows you to adjustthe various audio settings. Access From the Main menu screen, press the left or right arrow key until Audio Setting is highlighted. Then the Audio Setting menu is displayed. Sound Control: Press the up or down arrow key to select Sound Controland right arrow key or ENTER key to access the sub menu. Use the up or down arrow key to move between the various settings, and the left or right arrow key to adjust them.

Password Setting _New Password Confirm Enter Password

Setup Menu

From the Main menu screen, press the left or right arrow key until Setup is highlighted.Then the Setup menu is displayed. Use the up or down arrow key to move between the various selections in this menu. Setup --+ Language Blue Back Closed Caption
Lanauaae: This feature allows you to pick a language used for the on screen display (OSD). Use the left or right arrow key to select the language of your choice - English (Eng.), French (Fra.), or Spanish (Esp.). Blue Backqround: This feature gives you the option to display a blue background on the TV screen when there is no signal present. Use the left or right arrow key to toggle between on and off.

English On CC1

I Move: t _

Exit:_E-N-_

Closed Caption: Closed caption is a feature that allows your TV set to display closed caption signal on screen. It also allows you to display teletext signal. There is nine different setting for closed caption. You can set it to one of the 4 Closed Caption settings (CC1-4), one of the 4 Text settings (T1-4), or set this feature to off (CCD/Text off).

L Useful Remote Control

of the TV screen (channel, antenna mode, time, video, etc.).
Display This key allows you to display the current Display disappears in about 6 seconds.

information

0-_.99
Press the 0-9 keys to enter channel numbers directly (2-69 in the Air mode or 1-125 in the Cable mode). 1.To choose a one-digit channel number, press the corresponding Number key directly to switch to the desired channel number in about 3 seconds. 2.To choose a two-digit channel number, enter a first-digit and then a second digit within 3 seconds. 3.To choose a three-digit channel number, enter a first-digit, second-digit and third-digit respectively mentioned above. in the way
Press the SCAN key to display the current channel No. and Scan mode (Scan On or Scan Off). Press the key firstly to display Scan Offon the screen. Press the key secondly to display Scan On on the screen. And the TV begins to scan through all active channels. Upon completion, the TV automatically returns to the current channel and shifts to the Off mode. Pressing any key can interrupt scanning.
Useful Remote Control Features (continued)
Picture Your TV has factory preset picture modes that allow you to optimize your TV viewing. To activate these picture modes, press the PICTURE key, and you can choose among User, Normal, Movie and Sports. Sound Press the SOUND key repeatedly, and you can choose among User, Normal, Movie, Speech and Music. Recall This key will allow you to return to the last channel you were viewing. Pressing it again will return you to the channel you just left. Favorite This key will display the favorite channel if a favorite channel is set. Ful___J This key will switch the TV between Wide and Normal modes.

Pressing the CC key will activate the currently selected Closed Caption or Text. Press the key repeatedly to select another mode in turn. /
oFF-ool- 004 T1 --T2--T3 T /
Video This key allows you to toggle between antenna mode and differentvideo modes cyclically: For PF2730 and PF3230:TV_Videol(S-VHS1)_Video2 _Video3_Video4(S-VHS4)_ DVD For PF2720 and PF3220: TV_Videol(S-VHS)_Video2_Video3_Video4_DVD For PF2030 and PF2020: TV_Videol_Video2_S-VHS--DVD

Child Lock

The Child Lock feature prevents unauthorized viewing of the TV. To activate, press and hold the F key, and then press MUTE. This will lock out all remote functions (except for Standby) and Child Lock On will be displayed for 6 sec. You can see only the current channel with normal picture and sound. With Child Lock set before turn-off, no picture and no sound are available from the TV if the TV is turned on again, but only Child Lock On displayed. To unlock the TV, press and hold the F key and press MUTE. This will unlock the TV. Please note that the only way to activate or deactivate the Child lock feature is via remote control - please insure that it is stored securely.
Press the SLEEP key repeatedly to switch the TV to one of the following modes cyclically: Off-* 15_30_45_60_ 90_120_150_180 (Unit: Minute). With Sleep Off set, press the SLEEP key firstly to display the remaining time and press it secondly to re-set the Sleep Off time. "TV will turn offsoon!" will be displayed on the screen one minute before the Sleep timer runs out.
MTS/SAP In the TV mode, the TV can automatically identify MTS stereo modes to one of Mono, Stereo, Stereo/SAP and Mono/SAP. Under no signal condition,the audio mode does not appear on the screen. When receiving signals from external equipment in the Video mode, Stereo is defined as default. Press the MTS/SAP key repeatedly to set Input to Stereo, L or R. Press the key firstly after OSD disappearsto display the auto-identifiedMTS mode. Press it again before the OSD disappearsto compulsorily set another MTS mode. Signal Received STEREO MONO/SAP STEREO/SAP MONO Label This key functions only in the TV mode. For an explanation of this feature, please see page 15. Press MTS/SAP key STEREO, MONO SAP, MONO STEREO, SAP, MONO MONO

ADDITIONAL

FEATURES the Remote Control l

Programming

1.Set the TV, DVD/VCR, SAT/CAB, AUX switch to the device you want to control
2.To program the remote control 1)Press and hold the SET key for over 3 seconds until the LED indicator on the remote control turns off. Release the key and the LED will light again. The remote control is now in the PROGRAMMING mode. 2)Use the 0-9 keys to enter three-digit code number for your device. If the right code number was entered, the LED blinks three times. If you enter a code not listed below, or you press any other keys than STANDBY and ENTER, the LED turns off.

528,531,532 528,531,532,540 529,539 527,530

Electric

526 534,535 537,536

AMPLIFIER

Aiwa ChangHong Carver Fisher JVC Magnavox

702 700,709 706,712 708

Memorex Panasonic Pioneer Proton Quasar RCA

703,704 7O707,713

Sony Techniques Toshiba Victor

702,711 706

Instruction Manual

TROUBLESHOOTING GUIDE

Check the following guide for a possible correction to a problem before contacting customer service. Check FAQ at our website: www.apexdigitalinc.com.

Symptoms No power

Correction - Verify the power cable to plug into an outlet with power. Verify the connection from the DVDNCR video output to the TV video input is secure. Then switch TV to the appropriate Video mode. Verify an antenna cable is securely connected to the RF in jack. Connect the audio cables into the terminals securely. Verify the connection from the DVD/VCR audio output to the TV audio input. Then switch to the appropriate mode on the receiver. Refer to your audio amplifier owner's manual. Verify the volume is at an appropriate level and the mute feature is not on. Make sure MTS feature is properly set. Verify the TV is set to Antenna mode. Make sure the antenna is securely connected to the RF in jack. Unplug the TV from the wall for 30 seconds, then plug in and try again. Unplug the antenna connection from the back of the TV, unplug the TV from the wall, wait 30 seconds, then try again.

No picture

No sound

No TV signal

Stripe or purple interference appears in the screen. Picture becomes snowy.
Verify the speakers around the TV set are shielded.
Verify the antenna lead wire is in working condition. - Verify the antenna is connected securely to the RF in jack. Move the antenna around to minimize multi-images. - The video frequency radiated from TV station can be reflected by tall buildings, high tower, etc. Make sure the Air/Cable setting is correct. - Channel may be locked with the block channel feature, such as Parental Control. Check Add/Erase feature, as channel may have been erased during set up. Verify Closed Caption feature is off. - Batteries may be weak. Replace batteries. Make sure nothing is located between the remote and the remote sensor. - Verify MTS feature is properly set.

Picture with multi-image

TV channel not received
Black box appears on screen. Remote control doesn't operate. No stereo or foreign language received.
Manual LIMITED UNITED STATES WARRANTY
(PF2020/PF2030/PF2720/PF2730/PF3220/PF3230)

Digital,

Inc. makes

the following

limited

warranties. consumer

These purchaser

warranties

extend
to the original consumer or transferee.

purchaser

or any person

receiving

this product
as a gift from the original
and to no other purchaser
Limited Ninety (90) Days Warranty
Apex Digital, original Center's retail refurbished an Authorized Inc. warrants this product purchase. During this part or product, Apex Digital, without and its parts against Apex Digital, to you. Depending defects in material or workmanship a defective it will either charges required for a period of ninety (90) days after the date of option, with a new or to For period charge Inc. will repair or replace part or product be performed at their

on the service

in your home or at the Service Center.

repair facility. When

repaired, Inc. Service
it will be returned Center. Apex Digital,
to your home at no cost to you. For 20" television, for all transportation personnel Center will come
you must deliver the entire product service is required.
You are responsible Inc. Service
for the set to and from the Service
27" and 32" televisions,

an authorized

to your home when warranty
Limited One (1) Year Warranty
Apex Digital, original replace the date Inc. further warrants the parts in this product of the remote you against defects in material or workmanship for ninety that if a defective for a period of one (1) year after the date of During this period Apex Digital, Inc. will packing, part is replaced after ninety (90) days from including all the entire product to an retail purchase a defective of original with exception purchase, charges Service control which is guaranteed all labor (90) days.

part with a new or refurbished retail

part without

charge to you, except charges

are responsible

to pay

involved in the part(s)

replacement
transportation Apex Digital,
and insurance Inc. Authorized
for the set to and from the Service Center. Center.

For 20" television,

you must also deliver
Limited Two (2) Years Warranty
Apex Digital, Inc. further warrants the picture tube in this product against defects in materials or workmanship for a period of two (2) years after the date of original retail purchase. During this period Apex Digital, Inc. will replace the defective picture tube at their option with a new or rebuilt picture tube or at their option replace or product is replaced in the replacement. the entire product with a new or refurbished product at no charge to you; if however you pay all labor, packing the defective picture tube involved after one (1) year from the date of the original retail purchase, and transportation charges

Rental Product

The warranty for a rental product begins with the original date of receipt by the rental firm.

YourResponsibility

The above warranties are subject to the following You must retain your bill of sale to provide For 20" television, All warranty These Labor systems service warranties service of this product conditions: proof of purchase. materials for return shipment. Apex Digital, Inc. Service in the U.S.A. controls and installation antenna or repair of any type of antenna or cable or cable system are your responsibility. Center. and operated of customer caused
you must retain all packing are effective
must be made by an Authorized adjustment problems
only if the product is purchased Reception

charges

for set installation, setup, by this warranty.

are not covered

by inadequate
Warranties extend only to defects in materials or workmanship as limited above and do not extend to any product or parts which have been lost or discarded by you or damage to product or parts caused by misuse, accident, damage caused by Acts of God, such as lightning or fluctuations in electrical power, improper installation, improper maintenance altered, or use in violation defaced or rendered of instructions illegible. furnished do by us; or to product not cover cosmetic which has been modified or had the serial number removed, Warranties

damages

or lost accessories.
How to Obtain Warranty Service
If after following all the operating instructions in this manual and reading the TROUBLESHOOTING section you find that service is necessary: service. for the product to the 1. Contact our Customer Service Center directly call 866-4-APEX-INC-(866-427-3946), Mon - Fri 8:30am - 5:00pm (California). 2. After obtaining the requested information, you must present your receipt to the Authorized Service Center to obtain warranty 3. For 20" television, when warranty you must deliver the entire product Center. is required. Depending to the Authorized required, Service Center. Apex Digital, You are responsible Inc. Service Center in your to and from the Service service authorized Apex Digital, For 27" and 32" televisions, on the service s repair facility an authorized personnel

for all transportation

will come to your home
it will either be performed
home or the set will be taken

Inc. Service Center'

for repair and then returned
to your home at no cost to you, while under the Limited
Ninety (90) Days Warranty.

Limitations

All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular purpose, are expressly limited to the duration of the limited warranties as set forth above. With the exception of any warranties implied by state law as hereby limited, the foregoing warranty is exclusive and in lieu of all other warranties, guarantees, agreements and similar obligations of manufacturers or seller with respect to the repair or replacement No person, whatsoever. any stature, discovered agent, of any parts. In no event shall Apex Digital, dealer or company is authorized Inc. be liable for consequential modify or extend of Apex (90) or incidental damages. the terms Digital, days of these warranties in any manner or under have

distributor,

to change, limited
The time within which action must be commenced or law of the United States or any state thereof, the defect. This limitation gives you specific warranty

to enforce is hereby

any obligation to ninety arising

Inc. arising

under this warranty
from the date you discover

or should

does not apply to implied warranties
under state law. may vary from state to state. Some states do not allow limitation or limitation of incidental or consequential damages, so

This warranty the above

rights and you may also have these rights which lasts, when an action may be brought,
on how long an implied provisions

or the exclusion

may not apply to you.
APEX Digital, Inc. Ontario, CA 91761 FOR SERVICE CALL: 866-4-APEX-INC http://www.apexdigitalinc.com