SyncMaster 223BW / 216BW

Install drivers

Install programs

Notation

Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.

Prohibited

Important to read and understand at all times

Do not disassemble

Disconnect the plug from the outlet

Do not touch

Ground to prevent an electric shock
When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode. The images here are for reference only, and are not applicable in all cases (or countries).
Do not use a damaged or loose plug. This may cause electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause electric shock or fire.
Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. (Class l Equipment only.)
Insert the power plug firmly so that it does not come loose. A bad connection may cause fire.
Do not bend the plug excessively and wire nor place heavy objects upon them, which could cause damage. This may cause electric shock or fire.
Do not connect too many extension cords or plugs to one outlet. This may cause fire.
Do not disconnect the power cord while using the monitor. A surge may be caused by the separation and may damage the monitor.
Do not use the power cord when the connector or plug is dusty. If the connector or plug of the power cord is dusty, clean it with a dry cloth. Using the power cord with a dusty plug or connector may cause an electric shock or fire.
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.
This may cause electric shock or fire.

Installation

Be sure to contact an authorized Service Center, when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. Failure to do so may cause serious damage to your monitor. Place your monitor in a location with low humidity and a minimum of dust. Failure to do so may cause electric shock or fire inside the monitor.
Do not drop the monitor when moving it. This may cause damage to the product or the person carrying it.
Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf. Dropping the product may cause damage to the product or the person carrying it.
Do not place the product on the floor. Take care, as someone, specifically children may trip over it.
Do not place the product on an unstable or small surface area. Place the product on an even and stable surface, as the product may fall and cause harm to someone walking by, specifically children.
TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES. Otherwise, this may cause fire.
Keep any heating devices away from the power cable. A melted coating may cause electric shock or fire.
Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc. Any increase in the internal temperature may cause fire.
Put down the monitor carefully. Failing to do so may damage the monitor.
Do not place the monitor face down. This may damage the TFT-LCD surface.
The installation of the bracket must be done by a qualified professional. Installing the bracket by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual.
When installing the product, make sure to keep it away from the wall (more than 10 cm/4 inches) for ventilation purposes. Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance.
Keep the plastic packaging (bag) out of children's reach. The plastic packaging (bag) may cause suffocation if children play with it.

Cleaning and Use

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.
Do not spray water or detergent directly onto the monitor. This may cause damage, electric shock or fire.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. A dirty connector may cause electric shock or fire.
Make sure to unplug the power cord before cleaning the product. Otherwise, this may cause electric shock or fire.

Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent.
Contact the SAMSUNG customer care center or Customer Center for interior cleaning once a year. Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause a malfunction or fire.

Others

Do not remove the cover (or back).
This may cause electric shock or fire. Refer to a qualified servicing company.
If your monitor does not operate normally - in particular, if there is any unusual sound or smell coming from the monitor - unplug it immediately and the Service Center. This may cause electric shock or fire.
Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. This may cause a malfunction, electric shock or fire. In particular, avoid operating the monitor near water or outdoors where it could be exposed to snow or rain.
If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center. The monitor may malfunction, causing electric shock or fire.
Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time. Failure to do so may cause electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire.
Do not place water containers, chemical products or small metal objects on the monitor.
This may cause a malfunction, electric shock or fire. If a foreign substance enters the monitor, unplug the power cord and contact the Service Center.

Keep the product away from combustible chemical sprays or inflammable substances. This may cause an explosion or fire.
Never insert anything metallic into the monitor openings. This may cause electric shock, fire or injury.
Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc. This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center.
When viewing a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy saving mode or set a screensaver to a changing picture when away from the monitor for an extended period of time.
Adjust the resolution and frequency to the level appropriate for the model. An inappropriate resolution may cause undesirable picture quality. 21.6 inch (55 cm) - 1680 X 1050
Viewing the monitor continuously at a too close angle may result in damage to your eyesight.
To ease eye strain, take at least a five-minute break after every hour of using the monitor.
Do not install the product on an unstable, uneven surface or a location prone to vibrations.
Dropping the product may cause damage to the product or the person carrying it. Using the product in a location prone to vibrations may shorten the lifetime of the product or may cause the product to catch fire.
When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor. Failure to disconnect cables may damage it and cause fire or electric shock.
Place the product out of children's reach, as they could damage by hanging onto it. A falling product may cause injury to the person or even fatality.
When not using the product for an extended period of time, keep the product unplugged. Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire.
Do not place your children's favorite toys or any other objects of interest on the product. Children may try to climb on the product to retrieve an object. The product could fall, causing injury or even fatality.
When lifting up or moving the monitor, do not lift the monitor upside down while holding only the stand. This may cause your monitor to fall, and become damaged or cause personal injury.

Good Postures When Using the Monitor
Try to maintain a good posture when using the monitor. Keep your back straight. Keep a distance of about 45 ~ 50 cm between your eyes and the monitor screen. Look at the screen from slightly above it, and have the monitor directly in front of you. Tilt the monitor upwards by 10 ~20 degrees. Adjust the monitor height so that the top of the monitor is slightly below eye level. Adjust the monitor angle so that there is no reflected light on the screen.Try to maintain your arms perpendicular to your armpits. Keep your arms level with the back of your hands. Keep the angle of the elbow perpendicular. Keep the angle of the knees at more than 90 degree. Do not let your feet fall up from the floor. Adjust the arm position so that it is below the heart.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only
(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
PRODUCT INFORMATION (Image Retention Free)
LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty. What is Image retention ? During normal operation of a LCD panel, pixel image retention doesn't occur. However, if the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display. Thus, the previous image is retained when switching to a new video image. All display products, including LCD,are subject to image retention. This is not a product defect. Please follow the suggestions below to protect your LCD from image retention Power Off, Screen Saver, or Power Save Mode Ex) Turn the power off when using a stationary pattern. - Turn the power off for 4 hours after 20 hours in use - Turn the power off for 2 hours after 12 hours in use Use a Screen saver if possible - Screen saver in one color or a moving image is recommended. Set the Monitor to power off with the PC Display Properties Power Scheme. Suggestions for specific applications Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems We recommend that you follow set up of your display system program as below: Display Information together with Logo or Moving image cycle. Ex) Cycle : Display Information for 1 hour followed by a Display Logo or moving image for 1 minute. Change the Color Information periodically (Use 2 different colors). Ex) Rotate the Color Information with 2 colors every 30 minutes.

Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Ex)
Recommended settings: Bright colors with little difference in luminance - Change the characters color and background color every 30 minutes Ex)
- Every 30 minutes, change the characters with movement.
The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel. The voltage difference between electrodes increases with time, forcing the liquid crystal to lean. When this occurs, the previous image may be seen when the pattern is changed. To prevent this, the accumulated voltage difference must be decreased.
Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II

Package Contents

Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.

Unpacking Without Stand

Monitor With Stand
Monitor & Simple stand

Manual

Quick Setup Guide
Warranty Card (Not available in all locations)
User's Guide, Monitor Driver, Natural Color Software, MagicTune Software

Power Cord

D-sub Cable

Cleaning Cloth

Sold separately

DVI Cable

Your Monitor
MENU button [ ] MagicBright button [ ]
Opens the on-screen menu and exits from the menu. MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently seven different modes are available: Custom, Text, Internet, Game, Sport and Movie, Dynamic Contrast. Each mode has its own pre-configured brightness value. You can easily select one of seven settings by simply pressing MagicBright control button. 1) Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu. 2) Text For documentations or works involving heavy text. 3) Internet For working with a mixture of images such as texts and graphics. 4) Game For watching motion pictures such as a game. 5) Sport For watching motion pictures such as a sport. 6) Movie For watching motion pictures such as a DVD or Video CD. 7) Dynamic Contrast Dynamic Contrast is to automatically detect distribution of inputted visual signal and adjust to create optimum contrast. >> Click here to see an animation clip

For wall mounts that do not comply with VESA standard screw specifications, the length of the screws may differ depending on their specifications. Do not use screws that do not comply with the VESA standard screw specifications. Do not fasten the screws too tightly, as this may damage the product or cause the product to fall, leading to personal injury. Samsung is not liable for these kinds of accidents. Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions. To mount the monitor on a wall, you should purchase the wall mounting kit that allows you to mount the monitor at least 10cm away from the wall surface. Contact the nearest Samsung Service Center for more information. Samsung Electronics will not be responsible for damages caused by using a base other than those specified. Please use Wall Mount according to the International standards.

Monitor Driver

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown below. Internet web site :http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China) Installing the Monitor Driver (Automatic) Insert the CD into the CD-ROM drive. Click "Windows". Choose your monitor model in the model list, then click the "OK" button.
If you can see following message window, then click the "Continue Anyway" button. Then click the "OK" button (Microsoft Windows XP/2000 Operating System).
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/
Monitor driver installation is completed.
Installing the Monitor Driver (Manual) Windows Vista | Windows XP | Windows 2000 | Windows ME | Windows NT | Linux

Microsoft Windows Vista Operating System Insert your Manual CD into your CD-ROM drive. Click (Start) and "Control Panel". Then, double-click on "Appearance and Personalization".
Click "Personalization" and then "Display Settings".
Click "Advanced Settings".
Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message Windows needs is displayed, as shown in the figure below, click "Continue".
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Click "Update Driver" in the "Driver" tab.
Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".
Click "Have Disk" and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK".
Select the model that matches your monitor from the list of monitor models on the screen, and click "Next".
Click "Close" "Close" "OK" "OK" on the following screens displayed in sequence.
Microsoft Windows XP Operating System Insert the CD into the CD-ROM drive. Click "Start" "Control Panel" then click the "Appearance and Themes" icon.
Click "Display" icon and choose the "Settings" tab then click "Advanced."
Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
Click "Update Driver." and select "Install from a list or." then click the "Next" button.
Select "Don't search ,I will." then click "Next" and then click "Have disk".
Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
If you can see following "Message" window, then click the "Continue Anyway" button. Then click the "OK" button.
Click the "Close" button then click the "OK" button continually.
Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. Choose the "OK" button on the "Insert disk" window. Click the "Browse" button on the "File Needed" window. Choose A:(D:\Driver) then click the "Open" button and then click the "OK" button.

How to install Click "Start," "Setting," and then "Control Panel." Double click the "Display" icon. Select the "Settings" tab and click the "Advanced Properties" button. Choose "Monitor." Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click "Update Driver." then click the "Next" button. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk". Click the "Browse" button then choose A:(D:\Driver). Click the "Open" button, then click the "OK" button. Choose your monitor model and click the "Next" button then click "Next" button. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click the "Finish" button then the "Close" button.
Microsoft Windows Millennium Operating System Click "Start," "Setting," and then "Control Panel." Double click the "Display" icon. Select the "Settings" tab and click the "Advanced Properties" button. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver." Choose "Display a list of all the driver in a specific location." then click the "Next" button. Click the "Have Disk" button. Specify A:\(D:\driver) then click the "OK" button. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.
Microsoft Windows NT Operating System Click "Start," "Settings," "Control Panel," and then double-click "Display" icon. In the Display Registration Information window, click the Settings tab and then click "All Display Modes". Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click "OK". Click the "Apply" button if you see the screen working normally after clicking "Test". If the screen is not normal, change to a different mode (lower mode of resolution, colors, or frequency). If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide.

Can you see "Not Optimum Mode", "Recommended Mode 1680 X Hz" on the screen?
You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly. If the display exceeds SXGA or 75 Hz, a "Not Optimum Mode", "Recommended Mode 1680 X Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly but the "Not Optimum Mode", "Recommended Mode 1680 X Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.)
There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals?
The monitor is in PowerSaver mode. Press a key on the keyboard to activate the monitor and restore the image on the screen. If there is still no image, press the 'SOURCE/ ' button. Then press any key on the keyboard again to activate the monitor and restore the image on the screen.
I cannot see the On Screen Display.
Have you locked the On Screen Display (OSD) Menu to prevent changes? Is the screen displaying only one color as if looking at the screen through a cellophane paper? Have the screen colors become strange after running a program or due to a crash between applications? Has the video card been set properly?
Unlock the OSD by pressing the [MENU / least 5 seconds.

] button for at

The screen shows strange colors or just black and white.
Check the signal cable connection. Make sure the video card is fully inserted in it's slot.

Reboot the computer.

Set the video card by referring to the video card manual.
The screen suddenly has become unbalanced.
Have you changed the video card or the driver? Have you adjusted the resolution or frequency to the monitor?
Adjust screen image position and size using the OSD.
Adjust the resolution and frequency at the video card. (Refer to the Preset Timing Modes).
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. The screen is out of focus or OSD cannot be adjusted. LED is blinking but no images on the screen. Have you adjusted the resolution or frequency on the monitor? Is the frequency properly adjusted when checking the Display Timing on the menu? Have the Windows colors been set properly? Adjust the resolution and frequency of the video card. (Refer to the Preset Timing Modes).

Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes. (The maximum frequency per resolution may differ from product to product.)
There are only 16 colors shown on the screen. The screen colors have changed after changing the video card.
Windows XP : Set the resolution at the Control Panel Appearance and Themes Display Settings. Windows ME/2000 : Set the resolution at the Control Panel Display Settings.
Has the video card been set properly? There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Have you installed the monitor driver? See the video card manual to see if the Plug & Play (VESA DDC) function can be supported. MagicTune feature is found only on PC (VGA) with Window OS that supports Plug and Play.
Install the monitor driver according to the Driver Installation Instructions. Install the monitor driver according to the Driver Installation Instructions.
Check when MagicTune does not function properly.
* To check whether your PC is available for MagicTune feature, follow the steps below (When Windows is XP); Control Panel Performance and Maintenance System Hardware Device Manager Monitors After deleting Plug and Play monitor, find 'Plug and Play
monitor' by searching new Hardware. MagicTune is an additional software for the monitor. Some graphic cards may not support your monitor. When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/magictune MagicTune doesn't work properly. Have you changed your PC or video graphic card? Did you install the program? Download the latest program. The program can be downloaded http://www.samsung.com/monitor/magictune
Reboot the computer after installing the program for the first time. If a copy of the program is already installed, remove it, reboot the computer, and then install the program again. You need to reboot the computer for it to operate normally after installing or removing the program.
Visit the MagicTune website and download the installation software for MagicTune MAC. Check the following items if there is trouble with the monitor. Check if the power cord and the video cables are properly connected to the computer. Check if the computer beeps more than 3 times when booting. (If it does, request an a service for the main board of the computer.) If you installed a new video card or if you assembled the PC, check if the installed the adapter(video) driver and the monitor driver. Check if the scanning ratio of the video screen is set to between 56 Hz ~ 75 Hz. (Do not exceed 75 Hz when using the maximum resolution.) If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter in the "Control Panel System Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. If problems repeatedly occur, contact an authorized service center.

Specifications

General Model Name LCD Panel Size Display area Pixel Pitch Synchronization Horizontal Vertical Display Color 16.7M Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, DVI Compliant Digital RGB, 0.7 Vp-p 5%, Separate H/V sync, Composite, SOG TTL level (V high 2.0V, V low 0.8V) Maximum Pixel Clock 146 MHz (Analog,Digital) Power Supply AC 100 - 240V~ (+/- 10%)50/60Hz 3 Hz 1680 X 1050@60 Hz 1680 X 1050@60 Hz 30 ~ 81 kHz 56 ~ 75 Hz 21.6 " Wide Diagonal (55 cm) 494.94 mm (H) x 290.5875 mm (V) 0.27675 mm (H) x 0.27675 mm (V) SyncMaster 223BW, 216BW
Signal Cable 15pin to 15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable (Option) Dimensions (W x H x D) / Weight 514.6 X 353.3 X 63.0 mm / 20.2 x 13.9 x 2.4 inch (Without Stand) 514.6 X 422.0 X 219.3 mm / 20.2 x 16.6 x 8.6 inch (With Stand) / 6.0 kg / 13.2 lbs VESA Mounting Interface 100 mm x 100 mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Temperature : 50 F ~ 104 F (10 C ~ 40 C) Humidity : 10 % ~ 80 %, non-condensing Temperature : -4 F ~113 F (-20 C ~ 45 C) Humidity : 5 % ~ 95 %, non-condensing

Storage

Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problelms. For example, the number of TFT LCD sub pixels contained in this product are 5,292,000. Design and specifications are subject to change without prior notice. Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)

Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
North America U.S.A CANADA MEXICO Latin America ARGENTINE BRAZIL CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA JAMAICA PANAMA PUERTO RICO REP. DOMINICA TRINIDAD & TOBAGO VENEZUELA Europe 0800-333-3733 4004-0000 800-726-7864 (SAMSUNG) 01-8000112112 0-800-507-7267 1-800-10-7267 800-6225 1-800-299-0013 1-800-234-7267 800-7267 1-800-682-3180 1-800-751-2676 1-800-7267-864 0-800-100-5303 http://www.samsung.com/ar http://www.samsung.com/br http://www.samsung.com/cl http://www.samsung.com.co http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin 1-800-SAMSUNG (7267864) 1-800-SAMSUNG (7267864) 01-800-SAMSUNG (7267864) http://www.samsung.com http://www.samsung.com/ca http://www.samsung.com/mx

BELGIUM CZECH REPUBLIC

000 844
http://www.samsung.com/be http://www.samsung.com/cz
DENMARK FINLAND FRANCE GERMANY HUNGARY ITALIA LUXEMBURG NETHERLANDS NORWAY POLAND PORTUGAL REPUBLIC OF IRELAND SLOVAKIA SPAIN SWEDEN SWITZERLAND U.K CIS ESTONIA LATVIA LITHUANIA KAZAKHSTAN RUSSIA UKRAINE UZBEKISTAN Asia Pacific AUSTRALIA CHINA HONG KONG
030-3260 SAMSUNG(7267864) ( 0,15/min) 01805 - 121213 ( 0,14/Min) 06-80-SAMSUNG (7267864) 800 SAMSUNG (7267864) 0032 (0)( 0,10/Min) 815-100 0800-SAMSUNG (7267864) 0771-0800-SAMSUNG (7267864)
http://www.samsung.com/dk http://www.samsung.com/fi http://www.samsung.com/fr http://www.samsung.de http://www.samsung.com/hu http://www.samsung.com/it http://www.samsung.lu http://www.samsung.com/nl http://www.samsung.com/no http://www.samsung.com/pl http://www.samsung.com/pt http://www.samsung.com/uk http://www.samsung.com/sk http://www.samsung.com/es http://www.samsung.com/se http://www.samsung.com/ch http://www.samsung.com/uk
800-7267 800-7267 8-800-1188 8-800-200-0400 8-800-502-0000 140-1234
http://www.samsung.ee http://www.samsung.com/lv http://www.samsung.lt http://www.samsung.kz http://www.samsung.ru http://www.samsung.com/ur http://www.samsung.uz
603 800-810-5858, 010- 3698-4698
http://www.samsung.com/au http://www.samsung.com.cn http://www.samsung.com/hk
INDIA INDONESIA JAPAN MALAYSIA PHILIPPINES SINGAPORE THAILAND TAIWAN VIETNAM Middle East & Africa SOUTH AFRICA U.A.E

3030 8282, 11 0800-112-8888 0120-327-527 1800-88-9999 1800-10-SAMSUNG (7267864) 1800-SAMSUNG (7267864) 1800-29-3232, 02-689-3232 0800-329-889
http://www.samsung.com/in http://www.samsung.com/id http://www.samsung.com/jp http://www.samsung.com/my http://www.samsung.com/ph http://www.samsung.com/sg http://www.samsung.com/th http://www.samsung.com/tw http://www.samsung.com/vn
(SAMSUNG) 800SAMSUNG (7267864) 8000-4726
http://www.samsung.com/za http://www.samsung.com/mea
Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit : mm
Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called the Vertical Frequency or Refresh Rate. Unit : Hz Example : If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit : kHz
Interlace and Non-Interlace Methods Showing the horizontal lines of the screen from the top to the bottom sequentially is called the NonInterlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.
Plug & Play This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function.

Resolution

The number of horizontal and vertical dots used to compose the screen image is called the 'resolution'. This number shows the accuracy of the display. A high resolution is good for performing multiple tasks as more image information can be shown on the screen. Example :If the resolution is 1680 X 1050 , this means the screen is composed of 1680 horizontal dots (horizontal resolution) and 1050 vertical lines (vertical resolution).

Do not place this product in a location exposed to moisture, dust, smoke, water, or in a car. Otherwise, this may result in electric shock or fire.
When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center. Otherwise, this may result in electric shock or fire.
If thunder or lightening is occurring, do not touch the power cord or antenna cable. Otherwise, this may result in electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable. Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.
Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables. Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.
Make sure that the ventilating opening is not blocked by a table or curtain. Otherwise, it may result in fire due to an increase in the internal temperature.
Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product. If water or a foreign material enters the product, disconnect the power cord and contact a Service Center. This may result in a product malfunction, electric shock, or fire.
Do not use or keep combustible spray or flammable material near the product. Otherwise, this may result in an explosion or fire.
Do not insert any metal, such as chopsticks, coins, pins and steel, or flammable objects, such as matches or paper, inside the product (through the ventilating openings, input and output terminals, etc). If water or foreign material enters the product, disconnect the power cord and contact a Service Center. Otherwise, this may result in electric shock or fire.
When using a fixed screen for a long time, an afterimage or stain may occur. If you are not using your product for a long period of time, put it into sleep mode or use a moving screen saver. Set a resolution and frequency appropriate to the product. Otherwise, your eyesight may be damaged.
When using headphones or earphones, do not turn the volume too high. Having the sound too loud may damage your hearing.
If you continually move closer to the product screen, your eyesight may be failing.
To ease eye strain, take at least a five-minute break after every hour of using the monitor.
Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations. Otherwise, it may fall and cause personal injury and/or damage the product. If you use the product in a location exposed to vibrations, it may damage the product and result in fire.

When moving the product, turn the power off and disconnect the power plug, antenna cable, and all the cables connected to the product. Otherwise, it may result in electric shock or fire.
Ensure that children do not hang onto the product or climb up onto the product. The product may fall and cause personal injury or death.
If you do not use the product for a long period of time, disconnect the power cord from the power outlet. Otherwise, this may result in overheating or fire due to dust, and may result in fire due to electric shock or leakage.
Do not place any heavy items or toys or confectionery, such as cookies etc. that may attract the attention of children and to the product. Your children may hang onto the product causing it to fall and this may result in personal injury or death.
Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that children or infants cannot reach. If children have had the battery in their mouths, consult your doctor immediately. When replacing the battery, insert it with right polarity (+, -). Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid.
Use only specified standard batteries. Do not use new and used batteries together. This may cause a battery to break or leak and may cause fire, injury, or contamination (damage).
The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling. The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery.
Do not turn the product upside down or move it while holding only the stand. Otherwise, it may fall and result in personal injury and/or damage to the product.
Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater. This may reduce the lifetime of the product, and may result in fire.

Activates a highlighted menu item. Push the ' ', button to change the input signal source.
Changing the source is only allowed for external devices connected to the product at the time. To switch Screen modes: [PC] [DVI] [TV] [Component] [HDMI1] [HDMI2] >> Click here to see an animation clip MENU Use this button to open the on-screen menu and to exit from the on-screen menu or to close the screen adjustment menu. - VOL+ Moves from one menu item to another horizontally or adjusts selected menu values. Adjusts the audio volume. - CH + Moves from one menu item to another vertically or adjusts selected menu values. In TV/DTV mode, selects TV/DTV channels. Power button [ ]
Use this button for turning the product on and off.
Note The button to the right of the monitor are touch-sensitive buttons. Touch a button lightly with your finger. Power indicator This light is lit when operating normally, and blinks once when your adjustments are saved. Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended for long periods. Speaker
Note The configuration at the back of the product may vary from product to product.
POWER POWER Connect the power cord for your monitor to the POWER port on the back of the product.
PC Connect the PC terminal at the back of your monitor to your computer.
HDMI/PC/DVI-D AUDIO IN DIGITAL AUDIO OUT(OPTICAL) EX-LINK HDMI/PC/DVI-D AUDIO IN Connect the [ HDMI/PC/DVI-D AUDIO IN ] terminal at the back of your product to your computers sound card. DIGITAL AUDIO OUT(OPTICAL) Connect the [DIGITAL AUDIO OUT(OPTICAL)] terminal of your product to the digital sound output or standard sound output terminal of the DVD home theater (or amplifier) using a digital audio optical output cable. EX-LINK This is a reserved terminal used for servicing. SERVICE SERVICE This is a reserved terminal used for servicing.
DVI-D DVI-D Connect the DVI cable to the DVI-D port on the back of your product.

Kensington Lock

The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Refer to the manual provided with the Kensington Lock for proper use. The locking device has to be purchased separately. Note The location of the Kensington Lock may be different depending on its model.
Using the Anti-Theft Kensington Lock
1. Insert the locking device into the Kensington slot on the Monitor ( locking direction ( 2. 3. HDMI IN 1 HDMI IN 1 Connect the [HDMI IN 1] terminal at the back of your monitor to the HDMI terminal of your digital output device using a HDMI cable. ). ) and turn it in the
Connect the Kensington Lock cable. Fix the Kensington Lock to a desk or a heavy stationary object.

COMPONENT IN R - AUDIO - L Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [ R - AUDIO - L] port of the product. PR, PB,Y Connect the VIDEO OUT port of the DVD / DTV Set-Top Box to the [ PR, PB,Y ] input ports using a component video cable ( PR, PB,Y ). ANT IN
Connect the CATV cable or TV antenna cable to the "ANT IN" port on the rear side of the product. Make sure to use a TV antenna cable (sold separately) as the antenna cable.
HDMI IN 2 / HDMI IN 2 Connect the [HDMI IN 2] terminal at the back of your product to the HDMI terminal of your digital output device using a HDMI cable.
Connect your headphones to the Headphone connection terminal. Note See Connecting Cables for further information regarding cable connections.
Cable holding ring Fix the cables using the holding ring, as shown in the figure.

Remote Control

POWER TV Number Buttons - button + VOL TOOLS Down-Up Left-Right buttons INFO COLOR BUTTONS CC MTS MENU SOURCE PRE-CH CH MUTE RETURN ENTER EXIT SRS FAV.CH P.SIZE 1. 2. POWER TV Turns the product On/Off. Selects the TV mode directly. Press to change the channel. The "-" button operates only for DTV. It is used to select MMS (multi-channel) for a DTV. Adjusts the audio volume. Use to quickly select frequently used functions. Moves from one menu item to another horizontally, vertically or adjusts selected menu values. Current picture information is displayed on the upper left corner of the screen. Press to add or delete channels and to store channels to the favorite channel list in the Channel List menu. Controls the caption decoder.
3. Number Buttons 4. - button 5. + VOL 6. TOOLS 7. Down-Up LeftRight buttons 8. INFO

9. COLOR BUTTONS 10. CC

Introduction 11. MTS You can select the MTS (Multichannel Television Stereo) mode. Mono, Stereo, SAP (Separate Audio Program) Set 'MTS' to ON to choose Mono, Stereo or SAP. 12. 13. MENU SOURCE Opens the on-screen menu and exits from the menu or closes the adjustment menu. Press the button to change the input signal SOURCE. Changing the SOURCE is only allowed for external devices that are connected to the monitor at the time. 14. PRE-CH 15. 16. 17. 18. 19. 20. CH MUTE RETURN ENTER EXIT SRS This button is used to return to the immediately previous channel. In TV mode, selects TV channels. Adjusts the audio volume. Returns to the previous menu. Activates a highlighted menu item. Exits from the menu screen. Not Available. Press to switch to your favorite channels. Press to change the screen size. PC / DVI mode : Wide / 4:3 TV / Component mode : Wide / 16:9 / Zoom1 / Zoom2 / 4:3 HDMI mode : Wide / 16:9 / Wide Fit / 4:3 / Just Scan

21. FAV.CH 22. P.SIZE

Connections
Connecting Cables Connecting to a Computer
Connect the power cord for your monitor to the POWER port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the [PC] port on the back of your monitor.
[PC] Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the [DVI-D] Port on the back of your Monitor.
[DVI-D] Connect the [ HDMI/PC/DVI-D AUDIO IN ] port on the rear side of the monitor to the sound card of the PC. Note You may enjoy clear and quality sound from the computer sound card using the monitor speakers. (You don't need to install any separate speakers for your computer.) You may get a blank screen depending on the type of video card you are using, if you connect simultaneously both the D-sub and DVI cables to one computer.
Connections If you connect properly your monitor using the DVI connector but get a blank or fuzzy screen, check to see if the monitor status is set to analogue. Press 'SOURCE [ ]' button to have the monitor double-check the input signal source.
Connecting to a Macintosh
1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the D-SUB port on the back of your monitor.
[PC] Note Turn on the monitor and Macintosh.
Connecting to Other devices
Note This monitor allows the user to connect it to such input devices as a DVD player, a VCR or camcorder, or a DTV or TV without disconnecting the PC. The configuration at the back of the monitor may vary from product to product. The DVI to HDMI cable, digital audio optic output cable, and RCA to stereo (for PC) cable are all sold separately. Contact a Service Center to purchase any products sold separately.

Connecting TV

Note You may view television programs on the monitor if it is connected to an antenna or CATV cable without installing any separate TV reception hardware or software on your computer.

Connecting and Using an Amplifier
Note You can connect the digital sound input (optical) or standard sound input terminal of your amplifier to your monitor using the correct cable.
Connect the [DIGITAL AUDIO OUT (OPTICAL)] terminal of your monitor to the digital sound input terminal of your digital amplifier using an optical cable.
Connections 2. 3. 4. Set the Internal Mute On in the Sound menu using the MENU button. Adjust the sound volume using the Volume button of your amplifier If the connections are set up, power up your monitor and amplifier. Note If no sound is emitted from the monitor, you need to use an amplifier. For information on how to connect a speaker and amplifier, refer to the respective user manuals provided by their manufacturers.

Connecting Headphone

Note You may connect your headphones to the monitor.
Connect your headphones to the Headphone connection terminal.
Using the Stand Monitor Assembly

Monitor and Bottom

Tilt angle
Note You can tilt the monitor upwards at an angle of -1 to 21.

Using the Software

Monitor Driver
Note When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (Worldwide)
Installing the Monitor Driver (Automatic)
1. 2. 3. Insert CD into the CD-ROM drive. Click "Windows". Choose your monitor model in the model list, then click the "OK" button.
If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button (Microsoft Windows XP/2000 Operating System).
Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/

Channel List

You can manage the channels.

MENU , MENU,EXIT

Note All selected channels will be shown on Added menu. , , , ,

MENU , MENU,EXIT

Favorite
Note Only memorized channels can be set as favorite channels. All favorite channels will be shown in the Favorite menu. , , , ,
If channel name information is broadcast when you store the channels either manually or automatically, the names are assigned to the channels directly. You can however change these names or assign new names as required. (Available in Analog TV Mode Only) MENU , , , , , , , MENU,EXIT

Fine Tune

Due to weak signals or an incorrect antenna configuration, some of the channels may not be tuned correctly. (Available in Analog TV Mode Only) MENU , , , , MENU,EXIT

Signal Strength

Unlike analog channels, which can vary in reception quality from "snowy" to clear, digital (HDTV) channels have either perfect reception quality or you will not receive them at all. So, unlike analog channels, you cannot fine tune a digital channel. You can, however, adjust your antenna to improve the reception of available digital channels. If the signal strength meter indicates that the signal is weak, physically adjust your antenna to increase the signal strength. Continue to adjust the antenna until you find the best position with the strongest signal. (Available in Digital Cable TV Mode Only) MENU , , MENU,EXIT

Setup Available Modes

Plug & Play
You can manage the entire configuration. MENU , , , , , MENU,EXIT , , , , ,

Language

You can choose one of 3 languages.
The language chosen affects only the language of the OSD. MENU , , MENU,EXIT

Time Clock

You can set the current time.

- Clock Mode

Auto / Manual MENU , , , MENU,EXIT

- Clock Set

Note Clock Set are available only when Clock Mode set to Manual. MENU , , , , , , MENU,EXIT

- Time Zone

Note Time Zone are available only when Clock Mode set to Auto. MENU , , , , MENU,EXIT
Note DST are available only when Clock Mode set to Auto. Depending on the broadcast station and signal, the auto time may not be set correctly. If this occurs, set the time manually. The Antenna or cable must be connected in order to set the time automatically. , , , , MENU,EXIT

Q: A: Q: A: Q: A: A: Q: A:
3. Problems related to Audio
Note Problems related to audio signals and their solutions are listed below. Q: A: A: Q: A: A: No sound Ensure that the audio cable is firmly connected to both the audio-in port on your monitor and the audio-out port on your sound card.(Refer to the Connecting the monitor) Check the volume level.(Refer to the Volume) The sound level is too low. Check the volume level.(Refer to the Volume) If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program.
4. Problems related to Remote Control
Note Problems related to the remote control and their solutions are listed. Q: A: A: A: The remote control buttons do not respond. Check the battery polarities (+/-). Check if the batteries have been exhausted. Check if the power is on.
Troubleshooting A: A: Check if the power cord is securely connected. Check if a special fluorescent or neon lamp is on in the vicinity
5. You may see small particles if you look closely at the edge of the bezel surrounding the screen.
This is part of the products design and is not a defect.

Q&A

Q: A: A: Q: A: How can I change the frequency? The frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjusts the resolution? Windows XP: Set the resolution in the Control Panel Appearance and Themes Display Settings. A: Windows ME/2000: Set the resolution in the Control Panel Display Settings. * Contact the video card manufacturer for details. Q: A: How can I set the Power Saving function? Windows XP: Set the resolution in the Control Panel Appearance and Themes Display Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). A: Windows ME/2000: Set the resolution at the Control Panel Display Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). Q: A: How can I clean the outer case/LCD Panel? Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any detergent or scratches on the case. Do not let any water enter the monitor. Q: A: What are the benefits of digital broadcasting? Digital TV broadcasting generates less noise and provides clearer visuals and sound than analog TV broadcasting does. As services develop, you can also enjoy various information services because various kinds of data besides video and audio can be sent. For example, while watching a sports game, you can view various data on your favorite player or you can view all or selected screens which have been captured from different angles for a

Troubleshooting A: If a cable broadcasting company is sharing a common broadcasting facility for your apartment or tenement house, it has to adjust and send digital TV signals so that they are compatible to shared viewing which is the original purpose of the common broadcasting facility.

Specifications

General
General Model Name LCD Panel Size Display area Pixel Pitch Synchronization Horizontal Vertical Display Color 16.2M Resolution Optimum resolution Maximum resolution 1680 x 1050 @ 60 Hz 1680 x 1050 @ 60 Hz 30 ~ 81 kHz 56 ~ 75 Hz 20 inch (51 cm) 433.44 mm (H) x 270.9 mm (V) 0.258 mm (H) x 0.258 mm (V) SyncMaster T200HD
Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) 0.7 Vp-p 5 % separate H/V sync, Composite TTL level (V high 2.0 V, V low 0.8 V) Maximum Pixel Clock 146.250 MHz (Analog, Digital) Power Supply AC 100 - 240 V~ (+/- 10 %), 50/60 Hz 3 Hz Signal Cable 15pin - to - 15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable Dimensions (W x H x D) / Weight 486 x 350 x 86 mm / 19.1 X 13.8 X 3.4 inch (Without Stand) 520 x 441.5 x 215 mm / 20.5 X 17.4 X 8.5 inch (With Stand) / 6.0 kg / 13.2 Ibs Environmental considerations Operating Temperature : 50 F ~ 104 F (10 C ~ 40 C)
Environmental considerations Humidity : 10 % ~ 80 %, non-condensing Storage Temperature : -4 F ~ 113 F (-20 C ~ 45 C) Humidity : 5 % ~ 95 %, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems. For example, the number of TFT-LCD sub pixels contained in this product are 5,292,000.
Note Design and specifications are subject to change without prior notice. Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)

Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
General Model Name LCD Panel Size 22 inch (55 cm) SyncMaster T220HD
LCD Panel Display area Pixel Pitch Synchronization Horizontal Vertical Display Color 16.2M Resolution Optimum resolution Maximum resolution 1680 x 1050 @ 60 Hz 1680 x 1050 @ 60 Hz 30 ~ 81 kHz 56 ~ 75 Hz 473.76 mm (H) x 296.1 mm (V) 0.282 mm (H) x 0.282 mm (V)
Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) 0.7 Vp-p 5 % separate H/V sync, Composite TTL level (V high 2.0 V, V low 0.8 V) Maximum Pixel Clock 146.250 MHz (Analog, Digital) Power Supply AC 100 - 240 V~ (+/- 10 %), 50/60 Hz 3 Hz Signal Cable 15pin - to - 15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable Dimensions (W x H x D) / Weight 520 x 373.5 x 86.5 mm / 20.5 X 14.7 X 3.4 inch (Without Stand) 520 x 441.5 x 215 mm / 20.5 X 17.4 X 8.5 inch (With Stand) / 6.2 kg / 13.7 Ibs Environmental considerations Operating Temperature : 50 F ~ 104 F (10 C ~ 40 C) Humidity : 10 % ~ 80 %, non-condensing Storage Temperature : -4 F ~ 113 F (-20 C ~ 45 C) Humidity : 5 % ~ 95 %, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor
Plug and Play Capability settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems. For example, the number of TFT-LCD sub pixels contained in this product are 5,292,000. Note Design and specifications are subject to change without prior notice. Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature. State Power Indicator Normal Operation Power saving mode Power off (Power button) EPA/ENERGY 2000 On Blinking Less than 2 watts Off Less than 1 watts

Power Consump- Less than 58 watts tion
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows. Display Mode Horizontal Frequency (kHz) 31.469 Vertical Frequency (Hz) 70.086 Pixel Clock (MHz) 25.175 Sync Polarity (H/V) +/-

IBM, 640 x 350

Display Mode
Horizontal Frequency (kHz) 31.469 31.469 35.000 49.726 68.681 37.861 37.500 35.156 37.879 48.077 46.875 48.363 56.476 60.023 67.500 60.000 63.981 79.976 65.290
Vertical Frequency (Hz) 59.940 70.087 66.667 74.551 75.062 72.809 75.000 56.250 60.317 72.188 75.000 60.004 70.069 75.029 75.000 60.000 60.020 75.025 59.954
Pixel Clock (MHz) 25.175 28.322 30.240 57.284 100.000 31.500 31.500 36.000 40.000 50.000 49.500 65.000 75.000 78.750 108.000 108.000 108.000 135.000 146.250
Sync Polarity (H/V) -/-/+ -/-/-/-/-/+/+ +/+ +/+ +/+ -/-/+/+ +/+ +/+ +/+ +/+ -/+
IBM, 640 x 480 IBM, 720 x 400 MAC, 640 x 480 MAC, 832 x 624 MAC, 1152 x 870 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1152 x 864 VESA, 1280 x 960 VESA, 1280 x 1024 VESA, 1280 x 1024 VESA, 1680 x 1050

Information

For Better Display
Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. Resolution: 1680 x 1050 Vertical frequency (refresh rate): 60 Hz
TFT-LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without any problems. For example, the number of TFT-LCD sub pixels contained in this product are 5,292,000.
When cleaning the monitor and the panel outside, please apply the recommended small amount of cleaner by using a soft cloth to polish. Do not force the LCD area but rub softly. If excessive force is applied, you may stain it. If you are not satisfied with the picture quality, you can get better quality of picture by performing the "Auto Adjustment function" in display screen that is appeared as window termination button is pressed. If there's still noise after the automatic adjustment, use the Fine/Coarse adjustment function. When viewing a fixed screen for an extended period of time, a residual image or blurriness may appear. Change the mode to energy save or set a screensaver to move the picture when you need to be away from the monitor for an extended period of time. Do not display a still image( such as on a video game or when hooking up a DVD to this LCD_TV ) on the Color TFT-LCD ( Thin Film Transister Liquid Crystal Display) panel for a long time as it can cause screen image retention. This image retention is also known as "screen burn". To avoid such image retention, reduce the degree of brightness and contrast of this screen when displaying a still image. Watching Digital Broadcasting Correctly Digital 16:9 HD Broadcasting Screen Digital SD Broadcasting Screen Digital 4:3 Broadcasting Screen

Interlace Methods

Non-Interlace

Resolution

Appendix curacy of the display. A high resolution is good for performing multiple tasks as more image information can be shown on the screen. Example: If the resolution is 1680(1920) x 1050(1200), this means the screen is composed of 1680(1920) horizontal dots (horizontal resolution) and 1050(1200) vertical lines (vertical resolution). RF Cable Satellite Broadcasting Cable TV A round signal cable generally used for TV antennas. Balances the levels of the sound coming from each speaker in televisions with two speakers. Whereas the terrestrial broadcasting is delivered via frequency signals through the air, cable broadcasting is transmitted via a cable network. In order to view cable TV, one must purchase a cable receiver and hook it up to the cable network. "CATV" refers to the broadcasting service offered at hotels, schools and other buildings through their own broadcasting system, apart from VHF or UHF broadcasting by terrestrial broadcasters. The CATV programs may include movies, entertainment and educational programs. (Different from cable TV.) CATV can be viewed only within the area in which the CATV service is offered. VHF/UHF Channel Fine Tuning VHF indicates TV channels 2 to 13, and UHF indicates channels 14 through 69. This feature allows the viewer to fine-tune the TV channel to obtain the best viewing conditions. The Samsung LCD TV has both automatic and manual channel fine-tuning features to enable the viewer to adjust their desired settings. External device input refers to video input from such external video devices as VCRs, camcorders and DVD players, separate from a TV broadcast. A type of digital disk technology that takes up only the benefits of CD and LD, to implement a high resolution/quality, which enables the user to enjoy clearer images. An enhanced broadcasting technology to process digital video signals using a set-top box, which implements a high resolution and clearer digital images on the screen. This derives from artificial satellite technology that amplifies weak signals even in poor reception areas for sharper images. A connection part that is used to link a Wide antenna cable (feeder cable) to the TV. A kind of language selection feature that provides English subtitles (caption) or character information services from broadcasting services (ex: AFKN) or video tapes (marked CC), and which are especially useful for studying English. This enables the user to enjoy the broadcasting service in both Korean and foreign (original) language as well as in stereo mode.

External Device Input

DTV Broadcasting (Digital TV Broadcasting) LNA (Low Noise Amplifier) Antenna Converter English Caption (= Caption Setting)

Multiplex Broadcasting

Appendix A2 BTSC This system uses two carriers to transmit voice data. Countries such as South Korea and Germany use this system. Broadcast Television System CommitteeThe stereo broadcasting system that is used in most of the countries that have adopted the NTSC system, including the United States, Canada, Chile, Venezuela and Taiwan. It also refers to the organization that has been organized to promote its development and management. Electronic Industries Association of Japan. DVI is the acronym for Digital Video Interface. It is a new type of video interface technology that provides the maximum screen quality for high quality display devices and high-end graphics cards including flat panel LCD monitors. This is an interface that connects both quality video signals and digital audio signals with a cable without any compression. HD (High Definition) In HD, 1080-line, 2x density beaming (1080i) is used. HD provides a five times clearer screen quality than the existing analog method and has a wide 16:9 aspect ratio. SD (Standard Definition) In HD, 480-line, double beaming (480i) is used. SD provides a screen quality somewhere between HD and the existing analog method. It exhibits a two times better screen quality than analog TV.