Reviews & Opinions
Independent and trusted. Read before buy Behringer 1222FX!

Behringer 1222FX

Manual

Download (English)
Behringer 1222FX, size: 2.2 MB
Related manuals
Behringer 1222FX Technical Specifications

Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Behringer 1222FXBehringer XENYEX1222FX Premium 16-Input 2/2-Bus Mixer w/XENYX Mic
Behringer Premium 16-Input 2/2-Bus Mixer - 1222fx - The 16-input XENYX 1222FX is an analog mixer that brings together old-school feel, onboard digital effects the endless possibilities of digital recording. Its included USB interface and energyXT2.5 Compact BEHRINGER Edition software will

Details
Brand: BEHRINGER
Part Numbers: 1222FX, 1222fx, XENYEX1222FX
UPC: 04033653020824, 4033653020824

 

[ Report abuse or wrong photo | Share your Behringer 1222FX photo ]

Video review

Behringer Xenyx 1222 FX Mixer

 

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

No opinions have been provided. Be the first and add a new opinion/review.

 

Documents

doc0

1.3 Before you get started

1.3.1 Shipment

Your mixing console was carefully packed in the factory to guarantee safe transport. Nevertheless, we recommend that you carefully examine the packaging and its contents for any signs of physical damage, which may have occurred during transit. If the unit is damaged, please do NOT return it to us, but notify your dealer and the shipping company immediately, otherwise claims for damage or replacement may not be granted.

2.1 Mono channels

2.1.1 Microphone and line inputs

1.3.2 Initial operation

Be sure that there is enough space around the unit for cooling purposes and to avoid over-heating. Please do not place your mixing console on high-temperature devices such as radiators or power amps. The console is connected to the mains via the supplied power cable. The console meets the required safety standards. Blown fuses must only be replaced by fuses of the same type and rating. Please note that all units must be properly grounded. For your own safety, you should never remove any ground connectors from electrical devices or power cables, or render them in perative. o Please ensure that only qualified people install and operate the mixing console. During installation and operation, the user must have sufficient electrical contact to earth, otherwise electrostatic discharges might affect the operation of the unit.
Fig. 2.1: Connectors and controls of mic/line inputs
MIC Each mono input channel offers a balanced microphone input via the XLR connector and also features switchable +48 V phantom power supply for condenser microphones. The XENYX preamps provide undistorted and noise-free gain as is typically known only from costly outboard preamps. Please mute your playback system before you activate the phantom power supply to prevent switch-on thumps being directed to your loud peakers. Please s also note the instructions in chapter 2.5 Rear view of 1222FX. LINE IN Each mono input also features a balanced line input on a " connector. Unbalanced devices (mono jacks) can also be connected to these inputs. Please remember that you can only use either the microphone or the line input of a channel at any one time. You can never use both simultaneously!
1.3.3 Online registration
Please do remember to register your new BEHRINGER equipment right after your purchase by visiting www.behringer.com (alternatively www.behringer.de) and kindly read the terms and conditions of our warranty carefully. Should your BEHRINGER product malfunction, our goal is to have it repaired as quickly as possible. To arrange for warranty service, please contact the retailer from whom the equipment was purchased. Should your BEHRINGER dealer not be located in your vicinity, you may directly contact one of our subsidiaries. Corresponding contact information is included in the original equipment packaging (Global Contact Information/European Contact Information). Should your country not be listed, please contact the distributor nearest you. A list of distributors can be found in the support area of our website (www.behringer.com). Registering your purchase and equipment with us helps us process your repair claims quicker and more efficiently. Thank you for your cooperation!

2.2.2 Equalizer stereo channels
The equalizer of the stereo channels is, of course, stereo. The filter characteristics and crossover frequencies are the same as those of the mono channels. A stereo equalizer is always preferable to two mono equalizers if frequency correction of a stereo signal is needed. There is often a discrepancy between the settings of the left and the right channels when using separate equalizers.
2.2.3 Aux sends stereo channels
In principle, the aux sends of the stereo channels function in just the same way as those of the mono channels. As aux send paths are always mono, the signal on a stereo channel is first summed to mono before it reaches the aux bus.
2.2.4 Balance, mute switch and channel fader
BAL The function of the BAL(ANCE) control corresponds to the PAN control in the mono channels. The balance control determines the relative proportion between the left and right input signals before both signals are routed to the main stereo mix bus. The MUTE switch, MUTE LED, CLIP LED and channel fader function in the same way as the mono channels.

2.2 Stereo channels

2.2.1 Channel inputs
Fig. 2.2: The equalizer of the input channels
2.1.3 Pan, mute switch and channel fader
The upper (HIGH) and the lower band (LOW) are shelving filters that increase or decrease all frequencies above or below their cut-off frequency. The cut-off frequencies of the upper and lower band are 12 kHz and 80Hz respectively. The mid band is configured as a peak filter with a center frequency of 2.5 kHz. Unlike shelving filters, the peak filter processes a frequency range that extends upwards and downwards around its middle frequency.
2.3 Connector panel and main section
Whereas it was useful to trace the signal flow from top to bottom in order to gain an understanding of the channel strips, we now look at the mixing console from left to right. The signals are, so to speak, collected from one point on each of the channel strips and then routed to the main section all together.
2.1.2 Aux sends (MON and FX)
2.3.1 Monitor send and FX send channels
Fig. 2.5: Stereo channel inputs Fig. 2.3: The AUX SEND controls in the channel strips

+15 +15

Aux sends take signals via a control from one or more channels and sum these signals to a so-called bus. This bus signal is sent to an aux send connector and then routed, for example, to an active monitor speaker or an external effects device. The return from an external effects device can then be brought back into the console via the aux return connectors. For situations that require effects processing, the aux sends are usually switched post-fader so that the effects volume in a channel corresponds to the position of the channel fader. If this were not the case, the effects signal of the channel would remain audible even when the fader is turned to zero. When setting up a monitor mix, the aux sends are generally switched to pre-fader; i.e. they operate independently of the position of the channel fader.

MON SEND Connect the input of your monitor power amp or an active monitor system here to make the monitor mix audible to the musicians on the stage. The signal mix is created using the channels MON controls. FX SEND The FX SEND connector outputs the signal you picked up from the individual channels using the FX controls. You can connect this to the input of an external effects device in order to process the FX bus master signal. Once an effects mix is created, the processed signal can then be routed from the effects device outputs back into the AUX RETURN connectors. If the connected effects processor receives no input signal, the FX MUTE switch is probably pressed and/ or the FX SEND control is too low. This also goes for the built-in effects processor. Adjust your external effects processor to 100% wet (effects signal only), because the effects signal is added to the main mix along with the dry channel signals.
2.3.4 CD/tape return channel, voice canceller and connection socket
sound system via the microphones. Such noise can in the worst-case scenario even irreparably damage loudspeaker membranes. The cool thing about this is that the main mix faders can remain open, so that you can play music from a CD at the same time. Similarly, the faders for the muted channels can also remain in their position. To bring in other sound sources, you can use the CD/tape inputs, stereo input channels 9 to 12 and the aux return inputs. CD/TAPE MUTE Using this switch, the input signal from the CD/tape inputs is muted. CD/TAPE RET(URN) This stereo fader assigns the input signal from the CD/tape inputs into the main mix.
2.3.3 Aux return connectors
Fig. 2.9: CD/tape return channel
This channel, intended especially for connecting stereo signal sources (CD players, DAT recorders or even sound cards) features a particularly practical feature: the VOICE CANCELLER. VOICE CANCELLER
Fig. 2.8: Aux return connectors
Fig. 2.10: 2-track connectors
CD/TAPE INPUT The CD/TAPE INPUT RCA connectors are provided for connecting a 2-track machine (e.g. DAT recorder) or also a CD player. They can also be used as stereo line input. Alternatively, the output signal of a second XENYX or BEHRINGER ULTRALINK PRO MX882 can also be connected. If you connect a hi-fi amplifier with a source selection switch to the CD/TAPE INPUT, you can easily switch between additional sources (e.g. cassette recorder, MDplayer, sound card etc.). Using the voice canceller function, you can process all signals being brought into your mixing console via these connectors. CD/TAPE OUTPUT These connectors are wired pre graphic EQ and pre XPQ surround function. They carry the main mix signal (unbalanced), effects mix included. Connect the CD/TAPE OUTPUT to the inputs of your recording device. If you wish to use your mixer solely for recording purposes, the main outputs are also an alternative.

AUX RETURN 1 The AUX RETURN 1 connectors generally serve as the return path for the effects mix generated using the FX send. This is where you connect the output signal of the external effects device. If only the left connector is used, the aux return 1 automatically operates in mono. You can also use these connectors as additional line inputs. AUX RETURN 2 The AUX RETURN 2 connectors are used exactly the same way as the AUX RETURN 1 connectors. If these connectors already function as additional inputs, you can route the effects signal back into the console via a different stereo channel, with the added benefit that the channel EQ can be used to adjust the frequency response of the effects return signal. In this instance, the FX control of the channel being used as an effects return should be turned fully counterclockwise, otherwise feedback problems can occur!
Here, you have a filter circuitry that lets you almost entirely remove the vocal portion of a recording. The filter is constructed in such a way that voice frequencies are targeted without majorly affecting the rest of the signal. Additionally, the filter seizes only the middle of the stereo image, exactly there where the vocals are typically located. Possible applications for the Voice Canceller are obvious: you can very simply stage background music for Karaoke events. Of course, you can also do this at home or at your rehearsal room before you hit the stage. Singers with their own band can practice singing difficult parts using a complete playback from a tape player or a CD, thus minimizing rehearsal time. STANDBY If the STANDBY switch is pressed, all input channels with a mic connector (XLR connector) are muted. During breaks or stage conversion, you can prevent noise from entering the
2.3.2 Monitor send and FX send connector
Fig. 2.7: Aux send connectors MON and FX
2.3.5 Main mix, main out connectors and headphone connector
Recording: For mastering, using a stereo compressor such as the COMPOSER PRO-XL MDX2600 can be recommended. Use it to custom-tailor the dynamic characteristics of your signal to the dynamic range of the recording equipment you are using. The signal is in this case passed on from the compressor into the recorder. PHONES The PHONES control adjusts the volume of the headphones connected to the PHONS/CTRL connector. If you connect active monitors or an amplifier, use this connector to adjust the output signal level.

Fig. 2.11: Main mix fader

2.5 Rear view of 1222FX

MAIN MIX Use the high-precision quality faders to control the output level of the main mix.
Fig. 2.13: PHONS/CTRL connector
PHONS/CTRL connector You can connect headphones to this " TRS connector. The connector can also be used for feeding active monitor loudspeakers (or an amplifier) in your control room. For this purpose, the signal is taken directly before it is passed on to the main mix faders.
Fig. 2.16: Voltage supply and fuse
FUSE HOLDER/IEC MAINS RECEPTACLE The console is connected to the mains via the cable supplied, which meets the required safety standards. Blown fuses must only be replaced by fuses of the same type and rating. The mains connection is made via a cable with IEC mains connector. An appropriate mains cable is supplied with the equipment. POWER Use the POWER switch to power up the mixing console. The POWER switch should always be in the Off position when you are about to connect your unit to the mains.
Fig. 2.12: Main out connectors
2.4 Graphic 7-band equalizer
MAIN OUT The MAIN outputs carry the MAIN MIX signal and are on balanced XLR connectors with a nominal level of +4 dBu. Depending on how you wish to use your mixer and which gear you own, you can connect the following equipment: Live PA systems: A stereo dynamics processor (optional), stereo equalizer (optional) and the stereo power amplifier for full-range loud-speakers with passive crossovers. If you wish to use multi-way loudspeaker systems without an integrated crossover, you have to use an active crossover and several power amplifiers. Often, limiters are already built into active crossovers (e.g. BEHRINGER SUPER-X PRO CX2310 and ULTRADRIVE PRO DCX2496). Active crossovers are implemented directly before the power amplifier, and they divide the frequency range into several segments that are first amplified in the amplifiers and then passed onto the corresponding loudspeakers.
2.3.6 Level meter and level setting
Fig. 2.15: The graphic stereo equalizer
The graphic stereo equalizer allows you to tailor the sound to the room acoustics. FBQ FEEDBACK DETECTION

Fig. 2.14: Level meter

To disconnect the unit from the mains, pull out the main cord plug. When installing the product, ensure that the plug is easily accessible. If mounting in a rack, ensure that the mains can be easily disconnected by a plug pull or by an all-pole disconnect switch on or near the rack. Attention: The POWER switch does not fully disconnect the unit from the mains. Unplug the power cord completely when the unit is not used for prolonged periods of time.
POWER The blue POWER LED indicates that the device is switched on.
The switch turns on the FBQ Feedback Detection System. It uses the LEDs in the frequency band faders to indicate the critical frequencies. On a per-need basis, lower the frequency range in question somewhat in order to avoid feedback. The graphic stereo equalizer has to be turned on in order to use this function.
PHANTOM The PHANTOM switch activates the phantom power supply for the XLR microphone inputs, which is required to operate condenser microphones. The red +48 V LED lights up when phantom power is on. As a rule, dynamic microphones can still be used with phantom power switched on, provided that they are wired in a balanced configuration. In case of doubt, contact the microphone manufacturer! Connect microphones before you switch on the phantom power supply. Please do not connect microphones to the mixer (or the stagebox/wallbox) while the phantom power supply is switched on. In addition, the monitor/PA loudspeakers should be muted before you activate the phantom power supply. After switching on, wait approx. one minute to allow for system stabilization. Caution! You must never use unbalanced XLR connectors (PIN 1 and 3 connected) on the MIC input connectors if you want to use the phantom power supply. SERIAL NUMBER Please note the important information on the serial number given in chapter 1.3.3.
These effect presets are designed to be added to dry signals. If you move the FX TO MAIN control, you mix the channel signal (dry) and the effect signal. This also goes for mixing effects signals with the monitor mix. The main difference is that the mix ratio is adjusted using the FX TO MON control. Of course, a signal has to be fed into the effects processor via the FX control in the channel strip for both applications.

4. Installation

4.1 Rack mounting
The packaging of your mixing console contains two 19" rack mount brackets which can be installed on the side panels of the console. Before you can attach the rack mount brackets to the mixing console, you need to remove the screws holding the left and right side panels. Use these screws to fasten the two brackets onto the console, being careful to note that each bracket fits a specific side. With the rack mount brackets installed, you can mount the mixing console in a commercially available 19" rack. Be sure to allow for proper air flow around the unit, and do not place the mixing console close to radiators or power amps, so as to avoid overheating. Only use the screws holding the mixing console side panels to fasten the 19" rack mounts.

Caution! You must never use unbalanced XLR connectors (pins 1 and 3 connected) on the MIC inputs if you intend to use the phantom power supply.
Fig. 3.2: Connection socket for the footswitch
1 = ground/shield 2 = hot (+ve) 3 = cold (-ve) output
FOOTSWITCH Connect a standard footswitch to the footswitch connector; use this to switch the effects processor on and off. A flashing dot at the bottom of the display indicates if the effects processor is muted via the footswitch. In chapter 4.2, you will find an illustration showing how to connect your footswitch correctly.

4.2 Cable connections

You will need a large number of cables for the various connections to and from the console. The following illustrations show the wiring of these cables. Be sure to use only high-grade cables.

strain relief clamp

For unbalanced use, pin 1 and pin 3 have to be bridged
Balanced use with XLR connectors Fig. 4.2: XLR connections
Strain relief clamp Sleeve Tip
3. Digital Effects Processor and Xpq Surround Function
3.1 Digital effects processor

SURROUND

PROGRAM

(PUSH)

sleeve tip

XPQ TO MAIN

Fig. 3.3: Digital Effects module and XPQ Surround Function control elements
LEVEL The LED level meter on the effects module should display a sufficiently high level. Take care to ensure that the clip LED only lights up at peak levels. If it is lit constantly, you are overloading the effects processor and this could cause unpleasant distortion. The FX SEND fader determines the level that reaches the effects module. PROGRAM
Fig. 3.1: Effects presets overview
sleeve pole 1/ground Sleeve (ground/shield)

tip pole 2

The footswitch connects both poles momentarily

Tip (signal)

24-BIT MULTI-EFFECTS PROCESSOR Here you can find a list of all presets stored in the multi-effects processor. This built-in effects module produces high-grade standard effects such as reverb, chorus, flanger, delay and various combination effects. The integrated effects module has the advantage of requiring no wiring. This way, the danger of creating ground loops or uneven signal levels is eliminated at the outset, completely simplifying the handling.
You can select the effect preset by turning the PROGRAM control. The display flashes the number of the current preset. To recall the selected preset, press the button; the flashing stops. You can also recall the selected preset using the footswitch.

Unbalanced " TS connector Fig. 4.3: " TS connector
1/ TS footswitch connector 4" Fig. 4.1: "TS footswitch connector
3.2 XPQ surround function
The surround function can be enabled/disabled with the XPQTOMAIN switch. This is a built-in effect that widens the stereo width, thus making the sound more lively and transparent. Use the SURROUND control to determine the intensity of this effect.

4.2.1 Audio connections

Please use commercial RCA cables to wire the 2-track inputs and outputs. You can, of course, also connect unbalanced devices to the balanced input/outputs. Use either mono plugs, or ensure that ring and sleeve are bridged inside the stereo plug (or pins 1 & 3 in the case of XLR connectors).
strain relief clamp sleeve ring tip

5. Specifications

Mono inputs
Microphone inputs (XENYX Mic Preamp) Type Mic E.I.N. (20 Hz - 20 kHz) @ 0 source resistance @ 50 source resistance @ 150 source resistance Frequency response Gain range Max. input level Impedance Signal-to-noise ratio Distortion (THD+N) Line input Type Impedance Gain range Max. input level Fade-out attenuation1 (Crosstalk attenuation) Main fader closed Channel muted Channel fader muted XLR, electronically balanced, discrete input circuitry -134 dB / 135.7 dB A-weighted -131 dB / 133.5 dB A-weighted -129 dB / 130.5 dB A-weighted <10 Hz - 150 kHz (-1 dB), <10 Hz - 200 kHz (-3 dB) +10 to +60 dB +12 dBu @ +10 dB Gain approx. 2.6 k balanced 110 dB / 112 dB A-weighted (0 dBu In @ +22 dB Gain) 0.005 % / 0.004 % A-weighted " TRS connector, electronically balanced approx. 20 k balanced 10 k unbalanced -10 to +40 dB +22 dBu @ 0 dB Gain Channels 9/10, 11/12 Type Impedance Gain range Max. input level CD/tape in Type Impedance Max. input level EQ mono channels Low Mid High Low cut EQ stereo channels Low Mid High MON/FX send Type Impedance Max. output level Aux returns Type Impedance Max. input level Main outputs Type Impedance Max. output level Headphone output Type Max. output level XLR microphone connector, electronically balanced approx. 2.6 k balanced 0 dB to +40 dB +2 dBu 2 x " TRS connector, unbalanced approx. 40 k @ 0 dB Gain -20 dB to +20 dB +22 dBu @ 0 dB Gain CD/tape out Type Impedance Max. output level DSP Converter Sampling rate 2 x " TRS connector, unbalanced approx. 40 k @ 0 dB Gain -20 dB to +20 dB +22 dBu @ 0 dB Gain RCA connectors approx. 10 k +22 dBu 80 Hz / 15 dB 2.5 kHz / 15 dB 12 kHz / 15 dB 80 Hz, 18 dB/oct. 80 Hz / 15 dB 2.5 kHz / 15 dB 12 kHz / 15 dB " TS connector, unbalanced approx. 120 +22 dBu " TRS connector, unbalanced approx. 10 k +22 dBu XLR, electronically balanced approx. 240 balanced / 120 unbalanced +28 dBu " TRS connector, unbalanced +19 dBu / 150 (+25 dBm) RCA connectors approx. 1 k +22 dBu Texas Instruments 24-bit Sigma-Delta, 64/128-times oversampling 40 kHz

[3] Upon validation of the warranty claim, the repaired or replacement product will
mechanically modied in any way. If the product needs to be modied or adapted in order to comply with applicable technical or safety standards on a national or local level, in any country which is not the country for which the product was originally developed and manufactured, this modication/adaptation shall not be considered a defect in materials or workmanship. This limited warranty does not cover any such modication/adaptation, regardless of whether it was carried out properly or not. Under the terms of this limited warranty, BEHRINGER shall not be held responsible for any cost resulting from such a modication/adaptation.
[3] This limited warranty covers only the product hardware. It does not cover
technical assistance for hardware or software usage and it does not cover any software products whether or not contained in the product. Any such software is provided AS IS unless expressly provided for in any enclosed software limited warranty.
[4] This limited warranty is invalid if the factory-applied serial number has been
altered or removed from the product.
[5] Free inspections and maintenance/repair work are expressly excluded from this
be returned to the user freight prepaid by BEHRINGER.
[4] Warranty claims other than those indicated above are expressly excluded.
PLEASE RETAIN YOUR SALES RECEIPT. IT IS YOUR PROOF OF PURCHASE COVERING YOUR LIMITED WARRANTY. THIS LIMITED WARRANTY IS VOID WITHOUT SUCH PROOF OF PURCHASE.
limited warranty, in particular, if caused by improper handling of the product by the user. This also applies to defects caused by normal wear and tear, in particular, of faders, crossfaders, potentiometers, keys/buttons, tubes, guitar strings, illuminants and similar parts.
[6] Damage/defects caused by the following conditions are not covered by this

2 Online registration

Please do remember to register your new BEHRINGER equipment right after your purchase at www.behringer.com under Support and kindly read the terms and conditions of our limited warranty carefully. Registering your purchase and equipment with us helps us process your repair claims quicker and more eciently. Thank you for your cooperation!
limited warranty: improper handling, neglect or failure to operate the unit in compliance with the instructions given in BEHRINGER user or service manuals; connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used; damage/defects caused by acts of God/Nature (accident, re, ood, etc) or any other condition that is beyond the control of BEHRINGER.

[7] Any repair or opening of the unit carried out by unauthorized personnel
3 Return authorization number
[1] To obtain warranty service, please contact the retailer from whom the equipment
(user included) will void the limited warranty.
[8] If an inspection of the product by BEHRINGER shows that the defect in question is
was purchased. Should your BEHRINGER dealer not be located in your vicinity, you may contact the BEHRINGER distributor for your country listed under Support at www.behringer.com. If your country is not listed, please check if your problem can be dealt with by our Online Support which may also be found under Support at www.behringer.com. Alternatively, please submit an online warranty claim at www.behringer.com BEFORE returning the product. All inquiries must be accompanied by a description of the problem and the serial number of the product. After verifying the products warranty eligibility with the original sales receipt, BEHRINGER will then issue a Return Materials Authorization (RMA) number.
[2] Subsequently, the product must be returned in its original shipping carton,
not covered by the limited warranty, the inspection costs are payable by the customer.
[9] Products which do not meet the terms of this limited warranty will be repaired
exclusively at the buyers expense. BEHRINGER or its authorized service center will inform the buyer of any such circumstance. If the buyer fails to submit a written repair order within 6 weeks after notication, BEHRINGER will return the unit C.O.D. with a separate invoice for freight and packing. Such costs will also be invoiced separately when the buyer has sent in a written repair order.
[10] Authorized BEHRINGER dealers do not sell new products directly in online
together with the return authorization number to the address indicated by BEHRINGER.
[3] Shipments without freight prepaid will not be accepted.
auctions. Purchases made through an online auction are on a buyer beware basis. Online auction conrmations or sales receipts are not accepted for warranty verication and BEHRINGER will not repair or replace any product purchased through an online auction.

4 Warranty Exclusions

[1] This limited warranty does not cover consumable parts including, but not limited
5 Warranty transferability
This limited warranty is extended exclusively to the original buyer (customer of authorized retail dealer) and is not transferable to anyone who may subsequently purchase this product. No other person (retail dealer, etc.) shall be entitled to give any warranty promise on behalf of BEHRINGER.
to, fuses and batteries. Where applicable, BEHRINGER warrants the valves or meters contained in the product to be free from defects in material and workmanship for a period of ninety (90) days from date of purchase.

Legal Disclaimer

6 Claim for damage
Subject only to the operation of mandatory applicable local laws, BEHRINGER shall have no liability to the buyer under this warranty for any consequential or indirect loss or damage of any kind. In no event shall the liability of BEHRINGER under this limited warranty exceed the invoiced value of the product.
Technical specifications and appearance are subject to change without notice. The information contained herein is correct at the time of printing. BEHRINGER accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained herein. Colors and specifications may vary slightly from product. BEHRINGER products are sold through authorized dealers only. Distributors and dealers are not agents of BEHRINGER and have absolutely no authority to bind BEHRINGER by any express or implied undertaking or representation. This manual is copyrighted. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind, for any purpose, without the express written permission of Red Chip Company Ltd. ALL RIGHTS RESERVED. 2009 Red Chip Company Ltd. Trident Chambers, Wickhams Cay, P.O. Box 146, Road Town, Tortola, British Virgin Islands
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
7 Limitation of liability
This limited warranty is the complete and exclusive warranty between you and BEHRINGER. It supersedes all other written or oral communications related to this product. BEHRINGER provides no other warranties for this product.
Responsible party name: BEHRINGER USA, Inc. Address: 18912 North Creek Parkway, Suite 200 Bothell, WA 98011, USA Phone: +Fax: +673 7647
8 Other warranty rights and national law
[1] This limited warranty does not exclude or limit the buyers statutory rights as a

consumer in any way.

[2] The limited warranty regulations mentioned herein are applicable unless they

Phone/Fax No.:

constitute an infringement of applicable mandatory local laws.
[3] This warranty does not detract from the sellers obligations in regard to any lack of
hereby declares that the product
conformity of the product and any hidden defect.
complies with the FCC rules as mentioned in the following paragraph: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

9 Amendment

Warranty service conditions are subject to change without notice. For the latest warranty terms and conditions and additional information regarding BEHRINGERs limited warranty, please see complete details online at www.behringer.com.
* BEHRINGER Macao Commercial Offshore Limited of Rue de Pequim No. 202-A, Macau Finance Centre 9/J, Macau, including all BEHRINGER group companies
ENGLISH This manual is available in English, German, French, Spanish, Italian, Russian, Polish, Dutch, Finnish, Swedish, Danish, Portuguese, Greek, Japanese and Chinese. There may also be more current versions of this document. Download them by going to the appropriate product page at:

doc1

1222FX

Users Manual

Version 1.0 January 2006

ENGLISH

XENYX 1222FX

IMPORTANT SAFETY INSTRUCTIONS
DETAILED SAFETY INSTRUCTIONS: 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. CAUTION: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside; refer servicing to qualified personnel. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

WARNING:

To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosurevoltage that may be sufficient to constitute a risk of shock.
This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.
13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15) CAUTION - These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions unless you are qualified to do so.
Premium 16-Input 2/2-Bus Mixer with XENYX Mic Preamps, British EQs, 24-Bit Multi-FX Processor and USB/Audio Interface
s Premium ultra low-noise, high headroom analog mixer
s 4 state-of-the-art XENYX Mic Preamps comparable to standalone boutique preamps s Neo-classic British 3-band EQs for warm and musical sound
s Studio-grade 24-bit stereo FX processor with 100 awesome presets including reverb, chorus, flanger, delay, pitch shifter and various multi-effects s USB/Audio Interface included to connect directly to your computer
s 7-band stereo graphic EQ allows precise frequency correction of monitor or main mixes s Revolutionary FBQ Feedback Detection System instantly reveals critical frequencies

CAUTION!

We would like to draw your attention to the fact that extreme volumes may damage your hearing and/or your headphones or loudspeakers. Turn the MAIN MIX faders and the PHONES control in the main section fully down before you switch on the unit. Always be careful to set the appropriate volume.

1.2 The users manual

The users manual is designed to give you both an overview of the controls, as well as detailed information on how to use them. In order to help you understand the links between the controls, we have arranged them in groups according to their function. If you need to know more about specific issues, please visit our website at http://www.behringer.com. Additional information and explanations about various music industry/audio technology terminology can be found on individual product pages as well as in the glossary in the ULTRANET area of www.behringer.com.
The block diagram supplied with the mixing console gives you an overview of the connections between the inputs and outputs, as well as the associated switches and controls.
2. CONTROL ELEMENTS AND CONNECTORS
This chapter describes the various control elements of your mixing console. All controls, switches and connectors will be discussed in detail.
For the moment, just try and trace the signal path from the microphone input to the MON SEND connector. Dont be put off by the huge range of possibilities; its easier than you think! If you look at the overview of the controls at the same time, youll be able to quickly familiarize yourself with your mixing console and youll soon be making the most of all its many possibilities.

2.1 Mono channels

2.1.1 Microphone and line inputs
1.3 Before you get started

1.3.1 Shipment

Your mixing console was carefully packed in the factory to guarantee safe transport. Nevertheless, we recommend that you carefully examine the packaging and its contents for any signs of physical damage, which may have occurred during transit.
If the unit is damaged, please do NOT return it to us, but notify your dealer and the shipping company immediately, otherwise claims for damage or replacement may not be granted.

1.3.2 Initial operation

Be sure that there is enough space around the unit for cooling purposes and to avoid over-heating. Please do not place your mixing console on high-temperature devices such as radiators or power amps. The console is connected to the mains via the supplied power cable. The console meets the required safety standards. Blown fuses must only be replaced by fuses of the same type and rating.
Fig. 2.1: Connectors and controls of mic/line inputs MIC Each mono input channel offers a balanced microphone input via the XLR connector and also features switchable +48 V phantom power supply for condenser microphones. The XENYX preamps provide undistorted and noise-free gain as is typically known only from costly outboard preamps.

Please note that all units must be properly grounded. For your own safety, you should never remove any ground connectors from electrical devices or power cables, or render them inoperative. Please ensure that only qualified people install and operate the mixing console. During installation and operation, the user must have sufficient electrical contact to earth, otherwise electrostatic discharges might affect the operation of the unit.
Please mute your playback system before you activate the phantom power supply to prevent switch-on thumps being directed to your loudspeakers. Please also note the instructions in chapter 2.5 Rear view of 1222FX.
1.3.3 Online registration
Please do remember to register your new BEHRINGER equipment right after your purchase by visiting www.behringer.com (alternatively www.behringer.de) and kindly read the terms and conditions of our warranty carefully. Should your BEHRINGER product malfunction, our goal is to have it repaired as quickly as possible. To arrange for warranty service, please contact the retailer from whom the equipment was purchased. Should your BEHRINGER dealer not be located in your vicinity, you may directly contact one of our subsidiaries. Corresponding contact information is included in the original equipment packaging (Global Contact Information/European Contact Information). Should your country not be listed, please contact the distributor nearest you. A list of distributors can be found in the support area of our website (www.behringer.com). Registering your purchase and equipment with us helps us process your repair claims quicker and more efficiently. Thank you for your cooperation!
LINE IN Each mono input also features a balanced line input on a 1/4" connector. Unbalanced devices (mono jacks) can also be connected to these inputs.
Please remember that you can only use either the microphone or the line input of a channel at any one time. You can never use both simultaneously!
INSERT Insert points enable the processing of a signal with dynamic processors or equalizers. They are sourced pre-fader, pre-EQ and pre-aux send. Unlike reverb or other effects devices, whose signals are usually added to the dry signal, dynamic processors are most effective on the complete signal. In this case, aux send paths are a less-than-perfect solution. It is better to interrupt the signal path and insert a dynamic processor and/or equalizer. After processing, the signal is routed back to the console at precisely the same point it left. However, the channel signal path is interrupted only if a plug is inserted into the corresponding jack (stereo phone plug: tip = signal output; ring = return input). All mono input channels are equipped with inserts. Inserts can also be used as pre-EQ direct outputs, without interrupting the signal path. To this end, you will need a cable fitted with mono phone plugs on the tape machine or effects device end, and a bridged stereo phone plug on the console side (tip and ring connected).

All mono input channels include a 3-band equalizer. All bands provide boost or cut of up to 15 dB. In the central position, the equalizer is inactive. The circuitry of the British EQs is based on the technology used in the best-known top-of-the-line consoles and providing a warm sound without any unwanted side effects. The result are extremely musical equalizers which, unlike simple equalizers, cause no side effects such as phase shifting or bandwidth limitation, even with extreme gain settings of 15 dB.
2.1.4 Pan, mute switch and channel fader
Fig. 2.2: The equalizer of the input channels The upper (HIGH) and the lower band (LOW) are shelving filters that increase or decrease all frequencies above or below their cut-off frequency. The cut-off frequencies of the upper and lower band are 12 kHz and 80Hz respectively. The mid band is configured as a peak filter with a center frequency of 2.5 kHz. Unlike shelving filters, the peak filter processes a frequency range that extends upwards and downwards around its middle frequency.
2.1.3 Aux sends (MON and FX)
Fig. 2.4: Channel fader and additional control elements PAN The PAN control determines the position of the channel signal within the stereo image. This control features a constant-power characteristic, which means the signal is always maintained at a constant level, irrespective of position in the stereo panorama.
Fig. 2.3: The AUX SEND controls in the channel strips
MUTE Use the MUTE switch to mute the channel. This means that the channel signal is no longer present in the main mix. However, the aux sends (MON and FX) remain active. MUTE LED The MUTE LED indicates that the relevant channel is muted.
CLIP LED The CLIP LED lights up when the input signal is driven too high. In this case, lower apparent frequency increase on the channel EQ to avoid distortion. For example, lower the mids and the highs somewhat to emphasize the bass. If you dont wish to change the EQ settings under any circumstances, try lowering the TRIM control somewhat (counterclockwise). If you inserted an external effects processor via the insert connector (e. g. a dynamic processor), then you should also control its output signal level. It should not be higher than its input signal level (0 dB). The channel fader determines the level of the channel signal in the main mix.
2.2.3 Aux sends stereo channels
In principle, the aux sends of the stereo channels function in just the same way as those of the mono channels. As aux send paths are always mono, the signal on a stereo channel is first summed to mono before it reaches the aux bus.
2.2.4 Balance, mute switch and channel fader

BAL The function of the BAL(ANCE) control corresponds to the PAN control in the mono channels. The balance control determines the relative proportion between the left and right input signals before both signals are routed to the main stereo mix bus. The MUTE switch, MUTE LED, CLIP LED and channel fader function in the same way as the mono channels.
Attention: Since the aux path for the effect processor is connected post-fader, the channel fader has to be turned up in order to get this channels signal to the effects processor!
2.3 Connector panel and main section
Whereas it was useful to trace the signal flow from top to bottom in order to gain an understanding of the channel strips, we now look at the mixing console from left to right. The signals are, so to speak, collected from one point on each of the channel strips and then routed to the main section all together.

2.2 Stereo channels

2.2.1 Channel inputs
2.3.1 Monitor send and FX send channels
Fig. 2.5: Stereo channel inputs Each stereo channel features two line-level inputs on 1/4" connectors for left and right channels. Channels 9/10 and 11/12 can also be used in mono if you only use the connector labeled L. Both channels 5/6 and 7/8 feature an additional balanced XLR input for microphones with available +48 V phantom power. All stereo channel strips have a TRIM control for level setting. In those channels in which a mic input is present in the channel, the TRIM control has two scales: just like in the mono channels, there is a 0 to +40 dB scale that shows the preamplification of the mic signal; the +20 to -20 dB scale shows the sensitivity for the corresponding input level that is applied to the line input. Both inputs can also be used with balanced or unbalanced connectors.
Fig. 2.6: Aux send controls of the main section A channel signal is routed to the MON(ITOR) send bus if the MON control is turned up on the corresponding channel. MON SEND The aux send control MON SEND acts as master control for the monitor bus and determines the level of the summed signal that is taken from the mixer via the MON SEND connector and that can for example be fed to an amplifier for monitor purposes. Using the audio signal from this output, you can also feed a subwoofer if you dont require stage monitors. To this end, you should implement a crossover in your signal path pre-subwoofer and pre-amplifier, so that only low frequencies are fed into the subwoofer. You can achieve the same effect by using the builtin graphical equalizer. Lower all frequencies above 160 Hz and assign the equalizer to Monitor.

2.2.2 Equalizer stereo channels
The equalizer of the stereo channels is, of course, stereo. The filter characteristics and crossover frequencies are the same as those of the mono channels. A stereo equalizer is always preferable to two mono equalizers if frequency correction of a stereo signal is needed. There is often a discrepancy between the settings of the left and the right channels when using separate equalizers.
When you use the MAIN MIX fader to reduce the overall volume, keep in mind that the subwoofer is still receiving a signal!
FX TO MON You can use this control to insert an effects signal from the built-in effects processor to your monitor mix. Of course, to do this, your effects processor must first receive a signal, i.e. the FX controls in the channel strips must be turned up, and the FX SEND fader (see fig. 2.6) hast to be open. MON MUTE If the MON MUTE switch is pressed, the monitor bus is muted, i.e. there is no signal at the MON SEND connector. FX SEND The FX SEND fader determines the overall level of the effects bus. Both external effects processors (via the FX SEND connector) and the built-in processor only receive an input signal if this control is open. FX TO MAIN Use the FX TO MAIN control to feed the effects signal into the main mix. If the control is turned all the way to the left, no effects signal can be heard. FX MUTE If the FX MUTE switch is pressed, the effects channel is muted, i.e. no signal is present at the FX SEND connector and the effects processor no longer receives an input signal.
You can also use these connectors as additional line inputs.
AUX RETURN 2 The AUX RETURN 2 connectors are used exactly the same way as the AUX RETURN 1 connectors. If these connectors already function as additional inputs, you can route the effects signal back into the console via a different stereo channel, with the added benefit that the channel EQ can be used to adjust the frequency response of the effects return signal.
In this instance, the FX control of the channel being used as an effects return should be turned fully counter-clockwise, otherwise feedback problems can occur!
2.3.4 CD/tape return channel, voice canceller and connection socket
2.3.2 Monitor send and FX send connector
Fig. 2.7: Aux send connectors MON and FX MON SEND Connect the input of your monitor power amp or an active monitor system here to make the monitor mix audible to the musicians on the stage. The signal mix is created using the channels MON controls. FX SEND The FX SEND connector outputs the signal you picked up from the individual channels using the FX controls. You can connect this to the input of an external effects device in order to process the FX bus master signal. Once an effects mix is created, the processed signal can then be routed from the effects device outputs back into the AUX RETURN connectors. Fig. 2.9: CD/tape return channel This channel, intended especially for connecting stereo signal sources (CD players, DAT recorders or even sound cards) features a particularly practical feature: the VOICE CANCELLER. VOICE CANCELLER Here, you have a filter circuitry that lets you almost entirely remove the vocal portion of a recording. The filter is constructed in such a way that voice frequencies are targeted without majorly affecting the rest of the signal. Additionally, the filter seizes only the middle of the stereo image, exactly there where the vocals are typically located. Possible applications for the Voice Canceller are obvious: you can very simply stage background music for Karaoke events. Of course, you can also do this at home or at your rehearsal room before you hit the stage. Singers with their own band can practice singing difficult parts using a complete playback from a tape player or a CD, thus minimizing rehearsal time. STANDBY If the STANDBY switch is pressed, all input channels with a mic connector (XLR connector) are muted. During breaks or stage conversion, you can prevent noise from entering the sound system via the microphones. Such noise can in the worst-case scenario even irreparably damage loudspeaker membranes. The cool thing about this is that the main mix faders can remain open, so that you can play music from a CD at the same time. Similarly, the faders for the muted channels can also remain in their position. To bring in other sound sources, you can use the CD/tape inputs, stereo input channels 9 to 12 and the aux return inputs.

2.3.5 Main mix, main out connectors and headphone connector
We would like to draw your attention to the fact that extreme volumes may damage your hearing and/ or your headphones or loudspeakers. Turn the MAIN MIX faders and the PHONES control in the main section fully down before you switch on the unit. Always be careful to set the appropriate volume.
Fig. 2.13: PHONS/CTRL connector PHONS/CTRL connector You can connect headphones to this 1/4" TRS connector. The connector can also be used for feeding active monitor loudspeakers (or an amplifier) in your control room. For this purpose, the signal is taken directly before it is passed on to the main mix faders. Fig. 2.11: Main mix fader MAIN MIX Use the high-precision quality faders to control the output level of the main mix.
2.3.6 Level meter and level setting
The graphic stereo equalizer allows you to tailor the sound to the room acoustics. FBQ FEEDBACK DETECTION The switch turns on the FBQ Feedback Detection System. It uses the LEDs in the frequency band faders to indicate the critical frequencies. On a per-need basis, lower the frequency range in question somewhat in order to avoid feedback. The graphic stereo equalizer has to be turned on in order to use this function.
Logically, at least one (ideally several) microphone channels have to be open for feedback to occur at all!
Fig. 2.14: Level meter POWER The blue POWER LED indicates that the device is switched on. +48 V The red +48 V LED lights up when the phantom power supply is switched on. The phantom power supply is necessary for condenser microphones and is activated using the corresponding switch on the rear of the device.
Feedback is particularly common when stage monitors (wedges) are concerned, because monitors project sound in the direction of microphones. Therefore, you can also use the FBQ Feedback Detection for monitors by placing the equalizer in the monitor bus (see MAIN MIX/MONITOR). EQ IN Use this switch to activate the graphic equalizer. When activated, the fader LEDs will illuminate. MAIN MIX/MONITOR This toggles the graphic equalizer between the main mix and the monitor mix. With the switch up (not depressed), the equalizer is active in stereo on the main mix, and inactive on the monitor mix. When the switch is depressed the equalizer is active in mono on the monitor mix, and inactive on the main mix.

Connect microphones before you switch on the phantom power supply. Please do not connect microphones to the mixer (or the stagebox/ wallbox) while the phantom power supply is switched on. In addition, the monitor/PA loudspeakers should be muted before you activate the phantom power supply. After switching on, wait approx. one minute to allow for system stabilization.

2.5 Rear view of 1222FX

LEVEL METER/CLIP The high-precision level meter accurately displays the appropriate signal level. LEVEL SETTING: When recording to a digital device, the recorders peak meter should not exceed 0 dB. This is because, unlike analog recordings, slightly excessive levels can create unpleasant digital distortion. When recording to an analog device, the VU meters of the recording machine should reach approx. +3 dB with lowfrequency signals (e.g. kick drum). Due to their inertia VU meters tend to display too low a signal level at frequencies above 1 kHz. This is why, for example, a Hi-Hat should only be driven as far as -10dB. Snaredrums should be driven to approx. 0 dB.
Fig. 2.16: Voltage supply and fuse FUSE HOLDER/IEC MAINS RECEPTACLE The console is connected to the mains via the cable supplied, which meets the required safety standards. Blown fuses must only be replaced by fuses of the same type and rating. The mains connection is made via a cable with IEC mains connector. An appropriate mains cable is supplied with the equipment. POWER Use the POWER switch to power up the mixing console. The POWER switch should always be in the Off position when you are about to connect your unit to the mains. To disconnect the unit from the mains, pull out the main cord plug. When installing the product, ensure that the plug is easily accessible. If mounting in a rack, ensure that the mains can be easily disconnected by a plug pull or by an all-pole disconnect switch on or near the rack.
The peak meters of your XENYX display the level virtually independent of frequency. A recording level of 0 dB is recommended for all signal types.
2.4 Graphic 7-band equalizer
Attention: The POWER switch does not fully disconnect the unit from the mains. Unplug the power cord completely when the unit is not used for prolonged periods of time.

Fig. 2.15: The graphic stereo equalizer
PHANTOM The PHANTOM switch activates the phantom power supply for the XLR microphone inputs, which is required to operate condenser microphones. The red +48 V LED lights up when phantom power is on. As a rule, dynamic microphones can still be used with phantom power switched on, provided that they are wired in a balanced configuration. In case of doubt, contact the microphone manufacturer!
Connect microphones before you switch on the phantom power supply. Please do not connect microphones to the mixer (or the stagebox/ wallbox) while the phantom power supply is switched on. In addition, the monitor/PA loudspeakers should be muted before you activate the phantom power supply. After switching on, wait approx. one minute to allow for system stabilization. Caution! You must never use unbalanced XLR connectors (PIN 1 and 3 connected) on the MIC input connectors if you want to use the phantom power supply.
In chapter 4.2, you will find an illustration showing how to connect your footswitch correctly.
Fig. 3.3: Digital Effects module and XPQ Surround Function control elements LEVEL The LED level meter on the effects module should display a sufficiently high level. Take care to ensure that the clip LED only lights up at peak levels. If it is lit constantly, you are overloading the effects processor and this could cause unpleasant distortion. The FX SEND fader determines the level that reaches the effects module. PROGRAM You can select the effect preset by turning the PROGRAM control. The display flashes the number of the current preset. To recall the selected preset, press the button; the flashing stops. You can also recall the selected preset using the footswitch.
SERIAL NUMBER Please note the important information on the serial number given in chapter 1.3.3.
3. DIGITAL EFFECTS PROCESSOR AND XPQ SURROUND FUNCTION
3.1 Digital effects processor
3.2 XPQ surround function
The surround function can be enabled/disabled with the XPQTOMAIN switch. This is a built-in effect that widens the stereo width, thus making the sound more lively and transparent. Use the SURROUND control to determine the intensity of this effect.

Fig. 4.5: Insert send return 1/4" TRS connector
Fig. 4.2: XLR connections Fig. 4.6: 1/4" TRS connector for headphones
Fig. 4.3: 1/4" TS connector

5. SPECIFICATIONS

Mono inputs Microphone inputs (XENYX Mic Preamp) Type XLR, electronically balanced, discrete input circuitry Mic E.I.N. (20 Hz - 20 kHz) @ 0 W source resistance -134 dB / 135.7 dB A-weighted -131 dB / 133.5 dB A-weighted @ 50 W source resistance @ 150 W source resistance -129 dB / 130.5 dB A-weighted Frequency response Gain range Max. input level Impedance Signal-to-noise ratio Distortion (THD+N) Line input Type Impedance Gain range Max. input level Fade-out attenuation1 (Crosstalk attenuation) Main fader closed Channel muted Channel fader muted Frequency response Microphone input to main out <10 Hz - 90 kHz <10 Hz - 160 kHz Stereo inputs Channels 5/6, 7/8 Microphone input Type Impedance Gain range Max. input level Stereo inputs Type Impedance Gain range Max. input level Channels 9/10, 11/12 Type Impedance Gain range Max. input level CD/tape in Type Impedance Max. input level <10 Hz - 150 kHz (-1 dB), <10 Hz - 200 kHz (-3 dB) +10 to +60 dB +12 dBu @ +10 dB Gain approx. 2.6 kW balanced 110 dB / 112 dB A-weighted (0 dBu In @ +22 dB Gain) 0.005% / 0.004% A-weighted 1/4" TRS connector, electronically balanced approx. 20 kW balanced 10 kW unbalanced -10 to +40 dB +22 dBu @ 0 dB Gain EQ mono channels Low Mid High Low cut EQ stereo channels Low Mid High MON/FX send Type Impedance Max. output level Aux returns Type Impedance Max. input level Main outputs Type Impedance Max. output level Headphone output Type Max. output level CD/tape out Type Impedance Max. output level DSP Converter Sampling rate XLR microphone connector, electronically balanced approx. 2.6 kW balanced 0 dB to +40 dB +2 dBu 2 x 1/4" TRS connector, unbalanced approx. 40 kW @ 0 dB Gain -20 dB to +20 dB +22 dBu @ 0 dB Gain 2 x 1/4" TRS connector, unbalanced approx. 40 kW @ 0 dB Gain -20 dB to +20 dB +22 dBu @ 0 dB Gain Main mix system data 2 Noise Main mix @ -oo, Channel fader -oo Main mix @ 0 dB, Channel fader -oo Main mix @ 0 dB, Channel fader @ 0 dB Power supply Mains Voltage Power consumption Fuse Mains connection Physical Dimensions (H x W x D) Weight (net) RCA connectors approx. 10 kW +22 dBu Measuring conditions:

1: 2: 1 kHz rel. to 0 dBu; 20 Hz - 20 kHz; line input; main output; unity gain. 20 Hz - 20kHz; measured at main output. Channels 1 - 4 unity gain; EQ flat; all channels on main mix; channels 1/3 as far left as possible, channels 2/4 as far right as possible. Reference = +6 dBu.
80 Hz / 15 dB 2.5 kHz / 15 dB 12 kHz / 15 dB 80 Hz, 18 dB/oct. 80 Hz / 15 dB 2.5 kHz / 15 dB 12 kHz / 15 dB 1/4" TS connector, unbalanced approx. 120 W +22 dBu 1/4" TRS connector, unbalanced approx. 10 kW +22 dBu XLR, electronically balanced approx. 240 W balanced / 120 W unbalanced +28 dBu 1/4" TRS connector, unbalanced +19 dBu / 150 W (+25 dBm) RCA connectors approx. 1 kW +22 dBu Texas Instruments 24-bit Sigma-Delta, 64/128-times oversampling 40 kHz

98 dB 85 dB 85 dB

+0 dB / -1 dB +0 dB / -3 dB
-99 dB / -101 dB A-weighted -84 dB / -87 dB A-weighted -80 dB / -82 dB A-weighted 100 - 240 V~, 50 - 60 Hz 40 W T 1.6 A H 250 V Standard IEC receptacle approx. 97 mm (3 7/8") x 345 mm (13 18/32") x 334 mm (13 5/32") approx. 3.80 kg (8.38 lbs.)
BEHRINGER is constantly striving to manintain the highest professional standards. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may differ from those listed or illustrated.

6. WARRANTY

1 OTHER WARRANTY RIGHTS AND NATIONAL LAW 1. This warranty does not exclude or limit the buyers statutory rights provided by national law, in particular, any such rights against the seller that arise from a legally effective purchase contract. 2. The warranty regulations mentioned herein are applicable unless they constitute an infringement of national warranty law. 2 ONLINE REGISTRATION Please do remember to register your new BEHRINGER equipment right after your purchase by visiting www.behringer.com (alternatively www.behringer.de) and kindly read the terms and conditions of our warranty carefully. Registering your purchase and equipment with us helps us process your repair claims quicker and more efficiently. Thank you for your cooperation! 3 WARRANTY 1. BEHRINGER (BEHRINGER International GmbH including all BEHRINGER subsidiaries listed on the enclosed page, except BEHRINGER Japan) warrants the mechanical and electronic components of this product to be free of defects in material and workmanship for a period of one (1) year* from the original date of purchase, in accordance with the warranty regulations described below. If the product shows any defects within the specified warranty period that are not excluded from this warranty as described under 5, BEHRINGER shall, at its discretion, either replace or repair the product using suitable new or reconditioned parts. In the case that other parts are used which constitute an improvement, BEHRINGER may, at its discretion, charge the customer for the additional cost of these parts. 2. If the warranty claim proves to be justified, the product will be returned to the user freight prepaid. 3. Warranty claims other than those indicated above are expressly excluded. 4 RETURN AUTHORIZATION NUMBER 1. To obtain warranty service, the buyer (or his authorized dealer) must call BEHRINGER (see enclosed list) during normal business hours BEFORE returning the product. All inquiries must be accompanied by a description of the problem. BEHRINGER will then issue a return authorization number. 2. Subsequently, the product must be returned in its original shipping carton, together with the return authorization number to the address indicated by BEHRINGER. 3. Shipments without freight prepaid will not be accepted. 5 WARRANTY REGULATIONS 1. Warranty services will be furnished only if the product is accompanied by a copy of the original retail dealers invoice. Any product deemed eligible for repair or replacement under the terms of this warranty will be repaired or replaced. s 2. If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level, in any country which is not the country for which the product was originally developed and manufactured, this modification/adaptation shall not be considered a defect in materials or workmanship. The warranty does not cover any such modification/adaptation, irrespective of whether it was carried out properly or not. Under the terms of this warranty, BEHRINGER shall not be held responsible for any cost resulting from such a modification/adaptation. 3. Free inspections and maintenance/repair work are expressly excluded from this warranty, in particular, if caused by improper handling of the product by the user. This also applies to defects caused by normal wear and tear, in particular, of faders, crossfaders, potentiometers, keys/buttons, tubes, guitar strings, illuminants and similar parts. 4. Damages/defects caused by the following conditions are not covered by this warranty: s improper handling, neglect or failure to operate the unit in compliance with the instructions given in BEHRINGER user or service manuals. connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used. damages/defects caused by force majeure or any other condition that is beyond the control of BEHRINGER.

5. Any repair or opening of the unit carried out by unauthorized personnel (user included) will void the warranty. 6. If an inspection of the product by BEHRINGER shows that the defect in question is not covered by the warranty, the inspection costs are payable by the customer. 7. Products which do not meet the terms of this warranty will be repaired exclusively at the buyers expense. BEHRINGER will inform the buyer of any such circumstance. If the buyer fails to submit a written repair order within 6 weeks after notification, BEHRINGER will return the unit C.O.D. with a separate invoice for freight and packing. Such costs will also be invoiced separately when the buyer has sent in a written repair order. 6 WARRANTY TRANSFERABILITY This warranty is extended exclusively to the original buyer (customer of retail dealer) and is not transferable to anyone who may subsequently purchase this product. No other person (retail dealer, etc.) shall be entitled to give any warranty promise on behalf of BEHRINGER. 7 CLAIM FOR DAMAGES Failure of BEHRINGER to provide proper warranty service shall not entitle the buyer to claim (consequential) damages. In no event shall the liability of BEHRINGER exceed the invoiced value of the product.
* Customers in the European Union please contact BEHRINGER Germany Support for further details.
Technical specifications and appearance subject to change without notice. The information contained herein is correct at the time of printing. The names of companies, institutions or publications pictured or mentioned and their respective logos are registered trademarks of their respective owners. Their use neither constitutes a claim of the trademarks by BEHRINGER nor affiliation of the trademark owners with BEHRINGER. BEHRINGER accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained herein. Colours and specification may vary slightly from product. Products are sold through our authorised dealers only. Distributors and dealers are not agents of BEHRINGER and have absolutely no authority to bind BEHRINGER by any express or implied undertaking or representation. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind, for any purpose, without the express written permission of BEHRINGER Spezielle Studiotechnik GmbH. BEHRINGER is a registered trademark. ALL RIGHTS RESERVED. 2006 BEHRINGER Spezielle Studiotechnik GmbH, Hanns-Martin-Schleyer-Str. 36-38, 47877 Willich-Mnchheide II, Germany. Tel. +9206 0, Fax +9206 4903

 

Tags

Eudora 7 HP-1800E Alcatel-lucent 4039 Temporis 10 3600 Plus Telescope N73-1 AQ12awan Felcom 15 Servers TC32LX24 Gr-d30 POT 3860 Variant XL-2100U PDC 2070 Dbrh1979 Review Compressor-STD-closed Room ERB36402W FAX-phone B70 DVP-NC615 LE26C450 ACT18X VGN-N21e-W Tangent Xdma6630 HT-C6500 Abm3000 II XG Proanimator Series GR59A Server Card DCR-TRV239E 3510I YST-SW215 SA220 Charger GC9040 UE22C4000 Whistler 1734 SGH-Z360 DVH940 Sedan 2001 WD-13401TB Wireless PAD Eton E100 RAM 2080 DV-HRD3 85806 Fujifilm E900 NP-R40 Plus Gmrs1202CH 26LC4 SCC-C4201P Rgbv3100 KX-TG7301FR 2968 PC ONE 125 SGH-U900 Soul 21PT4475 SPA2300 Manual GR-399SQ Universal 55T03 Nikkor WT7300 DS19390 MFC-3820CN Nuvi 265W KP-44PX2U SGH-I617 ES 2084 206BW ES-8000 GA-15 GYA352 Montana 2003 Amarys 220 X5340 Charger GT-CC-01 RHT-G550 YFP-70 Chrono Copier PSC 2550 MCD11E3B R-633 F LVP-X390U Temporis 12 VGN-FW21E GC2520 BDV-Z7 Mixer Finepix 1300 DUO 3214 24-230 BV BF-030 W

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101