USERS GUIDE
Please keep all information for future reference. Safety Precautions Before trying to use the keyboard, be sure to read the separate Safety Precautions.

Espaol

GUA DEL USUARIO
Guarde toda la informacin para futuras consultas. Precauciones de seguridad Antes de intentar usar el teclado, asegrese de leer las Precauciones de seguridad separadas.

CTK4000/5000ES1B

English

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.
Declaration of Conformity
Model Number: CTK-4000/CTK-5000 Trade Name: CASIO COMPUTER CO., LTD. Responsible party: CASIO AMERICA, INC. Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801 Telephone number: 973-361-5400 This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Important!

Please note the following important information before using this product. Before using the optional AC Adaptor to power the unit, be sure to check the AC Adaptor for any damage first. Carefully check the power cord for breakage, cuts, exposed wire and other serious damage. Never let children use an AC adaptor that is seriously damaged. Never attempt to recharge batteries. Do not use rechargeable batteries. Never mix old batteries with new ones. Use recommended batteries or equivalent types. Always make sure that positive (+) and negative () poles are facing correctly as indicated near the battery compartment. Replace batteries as soon as possible after any sign they are getting weak. Do not short-circuit the battery terminals. The product is not intended for children under 3 years. Use only a CASIO AD-5 (for CTK-4000) or AD-12 (for CTK-5000) adaptor. The AC adaptor is not a toy. Be sure to disconnect the AC adaptor before cleaning the product.
This mark applies in EU countries only.
Manufacturer: CASIO COMPUTER CO.,LTD. 6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan Responsible within the European Union: CASIO EUROPE GmbH Bornbarch 10, 22848 Norderstedt, Germany

Company and product names used in this manual may be registered trademarks of others. Any reproduction of the contents of this manual, either in part or its entirety, is prohibited. Except for your own, personal use, any other use of the contents of this manual without the consent of CASIO is prohibited under copyright laws. IN NO EVENT SHALL CASIO BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF INFORMATION) ARISING OUT OF THE USE OF OR INABILITY TO USE THIS MANUAL OR PRODUCT, EVEN IF CASIO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. The contents of this manual are subject to change without notice.

Contents

General Guide.. E-4
Using the 10-key Pad (br)..E-6 FUNCTION Button (cs) Functions.E-6
Playing Built-in Songs. E-25
Playing the Demo Songs.. E-25 Playing Back a Particular Song. E-26 Increasing the Selection of Songs. E-28
Getting Ready to Play. E-8
Preparing the Music Stand..E-8 Power Supply...E-8
Using Built-in Songs to Master Keyboard Play. E-29
Phrases.. E-29 Step Up Lesson Flow.. E-29 Selecting the Song, Phrase, and Part You Want to Practice.. E-30 Lessons 1, 2, and 3.. E-31 Lesson Settings.. E-32 Using Auto Step Up Lesson.. E-34
Playing the Digital Keyboard.. E-9
Turning on Power and Playing..E-9 Using Headphones..E-9 Changing Keyboard Response to Touch Pressure (Touch Response).E-10 Adjusting Display Contrast.E-10 Using the Metronome..E-11
Controlling the Keyboard Sounds. E-12
Select from a variety of musical instrument sounds..E-12 Layering Two Tones...E-13 Splitting the Keyboard between Two Different Tones..E-13 Using Reverb..E-14 Using Chorus..E-14 Using a Pedal...E-15 Changing the Pitch (Transpose, Tuning, Octave Shift)..E-15 Using the Pitch Bend Wheel to Shift the Pitch of Notes (CTK-5000 Only)..E-16
Music Challenge Keyboard Game. E-35 Using Auto Accompaniment. E-36
Playing the Rhythm Part Only. E-36 Playing All Parts.. E-37 Using Auto Accompaniment Effectively. E-39 Using One-Touch Preset.. E-40 Using Auto Harmonize.. E-41

St r i ngs

4. Play something on the keyboard.
Both tones sound at the same time.

you want.

Example: 056 VIBRAPHONE 1 (CTK-5000)
5. Pressing cp again to unlayer the keyboard (so it
plays only the tone you selected in step 1).
Each press of cp toggles between layered (two tones) and unlayered (one tone).

Vi bes 1

This will sound the tones assigned to the left and right side ranges of the keyboard.
VIBRAPHONE 1 Split point FLUTE 1

Disappears F3

Splitting the Keyboard between Two Different Tones
5. Pressing co again to unsplit the keyboard (so it
Each press of co toggles between split (two tones) and unsplit (one tone).

Using Reverb

Reverb adds reverberation to notes. You can change the duration of the reverb.
and [6] ( E-6). ) keys to display Reverb (page

Disappears

If you turn on both layer and split, layering will be applied to the right side range of the keyboard only.

Re v e r b

2. Use the br (10-key) [] and [+] keys to select the

reverb setting you want.

Off (oFF) 1 to 10 Turns off reverb. The larger the number selected, the longer the reverb duration.
Indicator disappears when reverb is turned off.
To change the split point
1. While holding down co, press the keyboard key
where you want the split point to be.
The key you press will become the lowest note of the right side range of the split keyboard. Example: Setting middle C (C4) as the split point.

Key name

Using Chorus
Chorus is a function that adds depth and breadth to notes. It makes you sound as if you are playing multiple instruments.
and [6] ( E-6). ) keys to display Chorus (page

Cho r u s

chorus type you want.
There are five chorus types, plus an off setting.
Indicator disappears when chorus is turned off.
The actual effect produced by chorus depends on the tone you are using.

Using a Pedal

A pedal can be used to change notes in various ways while playing. A pedal unit does not come with the Digital Keyboard. Purchase one separately from your retailer. See page E-3 for information about options.
Changing the Pitch in Semitone Steps (Transpose)
The transpose feature lets you change the pitch, in semitone steps. A simple operation lets you instantly change the pitch to match that of a singer. The transpose setting range is 12 to +12 semitones.

protection.

Once protected a tone cannot be deleted. A protected tone is indicated as shown below.

*1 : O r

Protected
Saving Sample Data on an External Device
SD memory card (CTK-5000 only) (page E-61) Computer (page E-68)
Maintaining Sampled Sound Data in Memory
After you save sampled sound data in memory, it will remain there as long as power is supplied to the keyboard. However, if you disconnect the AC adaptor when there are no batteries loaded, sampled sound data will be deleted. Tips for Maintaining Data Use both batteries and the AC adaptor together. Make sure that batteries with sufficient power are loaded whenever you disconnect the AC adaptor. Connect the AC adaptor to the keyboard and plug it into a power outlet before replacing batteries. Before connecting or disconnecting the AC adaptor or replacing batteries, first press 1 to turn off power.

Playing Built-in Songs

With this Digital Keyboard, built-in tune data is referred to as songs. You can listen to the built-in songs for your own enjoyment, or you can play along with them for practice.
2. To change to another song while demo playback is in progress, use br (10-key) [] and
[+] keys to enter the song number you want (page E-6).
This will cause demo playback to jump to the song whose number you entered. You cannot use br (10-key) number buttons to select a song.
In addition to simple listening enjoyment, the built-in songs can be used with the lesson system (page E-29) for practice. You can increase the number of tunes using your SD memory cards (CTK-5000 only) (page E-62) or computer (page E-65).
3. To stop demo playback, press bl.
Demo playback continues until you stop it by pressing bl.

Playing the Demo Songs

Use the following procedure to play back built-in songs.
1. Press bl and bm at the same time.
This will start playback of the demo songs. See page E-75 for information about song numbers and the song sequence. Demo playback always starts from song number 151.

Flashes Song number

DemoTune

Tune name

Playing Back a Particular Song
Use the procedure below to play back one of the built-in songs. You can play along on the keyboard with song playback.
Pause, Skip Forward, Skip Back
Use the operations in this section to perform pause, skip forward, and skip back operations.

Pause

1. Press bk.
This pauses song playback.

Song number

1. Press bq.
2. Press bk again to resume playback from the
point where you paused it. Skip Forward

Tw i n k l e

1. Press 9.
This skips song playback forward to the next measure. Each press of 9 skips ahead one measure. Holding down 9 skips forward at high speed until you release it. Pressing 9 while song playback is stopped performs lesson function phrase skip forward (page E-30).
2. Use br (10-key) to enter the number of the song
See page E-75 for a complete list of available songs.

3. Press bl.

This starts playback of the song.
Tempo Note Sustain pedal Measure number Beat Measure

Skip Back

1. Press 8.
This skips song playback back to the previous measure. Each press of 8 skips back one measure. Holding down 8 skips back at high speed until you release it. Pressing 8 while song playback is stopped performs lesson function phrase skip back (page E-30).

Key Fingering

4. Press bl again to stop playback.
Song playback will continue (repeat) until you press bl to stop it. You can cancel song repeat by pressing 7 (REPEAT indicator disappears from the display).
Repeating Playback of Specific Measures
You can use the procedure in this section to repeat particular measures for practice playing along until you master it. You can specify the start measure and the end measure of the section you want to play and practice.

Start End

4. Pressing 7 again returns to normal playback.
Changing the song number clears the start measure and end measure of the repeat operation.
These measures are repeated.
Changing Playback Speed (Tempo)
1. Press 7 to temporarily turn off song repeat
(REPEAT disappears from the display).
2. When song playback reaches the measure you want to specify as the start measure, press 7.

CASIO CHORD Fingering Chord Type Major Chords Letters above the accompaniment keyboard indicate the chord assigned to each key. Pressing a single accompaniment area key in the CASIO CHORD mode will play the major chord whose name is marked above the key. All of the accompaniment area keys that are marked with the same chord name play exactly the same chord. Minor Chords To play a minor chord, press the accompaniment area key that corresponds to the major chord, while also pressing one other accompaniment area key to the right. Seventh Chords To play a seventh chord, press the accompaniment area key that corresponds to the major chord, while also pressing two other accompaniment area keys to the right. Minor Seventh Chords To play a minor seventh chord, press the accompaniment area key that corresponds to the major chord, while also pressing three other accompaniment area keys to the right. Example C (C Major)
C C#D Eb E F F#G Ab A Bb B C C#DEb E F
FINGERED 1 Play the component notes of the chord on the keyboard. FINGERED 2 Unlike FINGERED 1, 6th input is not b possible. m7 or mis input. FINGERED 3 Unlike FINGERED 1, allows input of fraction chords with the lowest keyboard note as the bass note.

Cm (C Minor)

C7 (C Seventh)

CASIO CHORD

With CASIO CHORD, you can use simplified fingerings to play the four types of chords described below.

Cm7 (C Minor Seventh)

When playing a minor, seventh, or minor seventh chord, it makes no different whether the additional keys you press are black or white.

FULL RANGE CHORD

With this mode, you can use the full range of the keyboard to play chords and the melody.
Accompaniment keyboard / Melody keyboard
Auto Accompaniment Pattern Variations
Use the following procedures to play intro and ending patterns, to play fill-in patterns, and to play variations of basic Auto Accompaniment patterns.

Normal Pattern Fill-in

Auto Accompaniment Variation
Each Auto Accompaniment pattern has a basic normal pattern as well as a variation pattern.
1. While a normal pattern is playing, press 8.
This plays the fill-in for the normal pattern. Normal pattern play will resume after the fill in pattern is complete.

Lights Lights

Each press of bs cycles through the bank numbers.

Bank 4

Re c a l l

Setup 6-1 recalled

You also can select a bank by holding down bs as you use the br (10-key) number buttons to enter a bank number.
4. While holding down cn, press a button from bt to cm to select an area.
This will save the settings you configured in step 2 into the applicable setup. If there is anything already stored in the setup, it will be replaced (deleted) by the new setup.
Notes currently being sounded by the keyboard may stop if you recall a setup that causes a change in octave shift (page E-16). To keep this from happening, either select a setup that does not cause a change in the octave shift setting, or hold down the pedal (which will cause notes currently being played to be sustained).
Saving registration Data on an External Device

Stored in Setup 4-1

Maintaining Data in Registration Memory
After you save data in registration memory, it will remain there as long as power is supplied to the keyboard. However, if you disconnect the AC adaptor when there are no batteries loaded, data in registration memory will be deleted. Tips for Maintaining Data Use both batteries and the AC adaptor together. Make sure that batteries with sufficient power are loaded whenever you disconnect the AC adaptor. Connect the AC adaptor to the keyboard and plug it into a power outlet before replacing batteries. Before connecting or disconnecting the AC adaptor or replacing batteries, first press 1 to turn off power.
To save a setup to registration memory
To recall a setup from registration memory
Recording Your Keyboard Play

bqbpbo br

The recorder feature lets you record your keyboard play.
4. Configure the tone, rhythm, and other settings

you want to use.

Recording and Playing Back Keyboard Play
Use the following procedure to record everything you play on the keyboard.

5. Start playing.

Recording starts as soon as you play something on the keyboard.

1. Press bp. 2. Press 4.

You can use Auto Accompaniment while playing. If you do, Auto Accompaniment also will be recorded.
6. To stop recording, press bl.

3. Press 4 again.

This will enter record stnadby.
7. To play back what you have recorded, press bl

again.

4. Press 3.

Now you can perform one of the scale editing operations described below.
Using the Scale Editor (CTK-5000 Only)
The Scale Editor provides you the following four options for changing the scale. Display Indicator Scale Fine Tune Quarter Tone Fin ScalMode qUA ScalMode Description Changes the tuning value in 1-cent steps within the range of +99 to 99 cents. Lowers the tuning value by 50 cents. Use the option to lower the E and G notes of the scale for Arabic music. Use this option to select from among a collection of preset scales. Changes the scale to the standard equal temperament.

Scale Fine Tune

1. Press the key whose note you want to change, and then use the br (10-key) [] and [+] keys to

change the tuning value.

2. After you are finished, press 3 to assign the

scale to the keyboard.

Tuning value

Preset

PrE ScalMode
Keyboard key The keyboard key(s) whose notes were changed will be lit.
Equal EqU Temperament ScalMode
1. Press bp. 2. Press 3 and cs at the same time.

Sca l Mode

Other Useful Digital Keyboard Functions Quarter Tone Preset
1. Press the key whose note you want to change, and then press the br (10-key) [] key to reduce
the tuning value by 50 cents. You can return to the original tuning by pressing [+].
1. Use the br (10-key) [] and [+] keys to select the
preset scale you want. After selecting a scale, press the key on the keyboard that you want to use as the root key (C to B).

Qu a : E

Keyboard key

Pu r eM i n r

Scale Name

No. 01 02

The keyboard key(s) whose notes were changed will be lit.
Scale name Pure Major Pure Minor Pythagorean Kirnberger 3 Werckmeister Mean-Tone Rast Bayati Hijaz Saba Dashti Chahargah Segah Gurjari Todi Chandrakauns Charukeshi
Display PureMajr PureMinr Pythagor Kirnbrg3 Wercmeis MeanTone Rast Bayati Hijaz Saba Dashti Chaharga Segah GujrTodi Cndrkuns Carukesi
You can perform a Quarter Tone operation without using the Scale Editor (page E-53). Hold down the 3 button and press the desired keyboard key. This will lower the tuning value of the keyboard key by 50 cents. If the tuning value of the key you press was previously lowered by 50 cents, performing the above operation will raise it +50 cents, which returns to its original value.

Equal Temperament

Select this option to change the keyboard scale to the standard equal temperament.
Recalling a Preset Scale (CTK-4000 Only)

Deleting All Data in Digital Keyboard Memory
Use the following procedure when you want to delete sampled sounds, user songs and all other data, except for recorded songs, currently in Digital Keyboard memory.
5. Press the br (10-key) [+] (YES) key.
Performing this procedure also will delete protected sampled sound data (page E-24). It is recommended that you save important data to a memory card (page E-59) or your computers hard disk (page E-65). This operation does not delete recorded song data.
2. Press the br (10-key) [7] (ENTER) key. 3. Use the br (10-key) [4] (
to display All Data. ) and [6] ( ) keys

A l l Da t a

Using a Memory Card (CTK-5000 Only)

3 bp br

Your Digital Keyboards SD memory card slot makes it possible for you to store record memory and other data on a commercially available SD memory card. Supported SD Memory Cards Your Digital Keyboard supports the use of memory cards up to 2 GB. Use of any SD memory card with greater capacity is not supported. See the instructions that come with the SD memory card for information about its capacity. User data that can be saved and loaded Data Type Sampled sound (page E-18) User rhythms (page E-42) User songs (page E-28) Recorded songs (page E-48) User scale memory (page E-53) Registration setups (page E-46) All data Description Sampled sound data Edited Auto Accompaniment data File Name Extension TW7 DW7*1 AC7
SD Memory Card and Card Slot Precautions
When using an SD memory card, make sure you observe all of the precautions in the instructions that come with it. SD memory cards have a write-protect switch that you can use to protect against accidental deletion of data. Avoid using an SD memory card under the following conditions. Such conditions can corrupt data stored on the memory card. Areas subjected to high temperature, high humidity, and corrosive gas Areas subjected to strong electrostatic charge and digital noise Never touch the contacts of an SD memory card when loading it or removing it from the Digital Keyboard. While data is being stored to or recalled from an SD memory card, never perform any other Digital Keyboard operation or remove the SD memory card. Doing so can corrupt the data on the card and damage the card slot. Never insert anything besides an SD memory card into the card slot. Doing so creates the risk of malfunction. Electrostatic charge discharging from your fingers or the SD memory card to the card slot can cause malfunction of the Digital Keyboard. If this happens, turn the Digital Keyboard off and then back on again. An SD memory card can become quite warm after very long use in the SD memory card slot. This is normal and does not indicate malfunction.

B connector USB cable (A-B type) Digital Keyboard USB port A connector
Never connect to a computer that does not conform to the above requirements. Doing so can cause problems with your computer.

Computer USB port

3. Turn on the Digital Keyboard.
If this is the first time you are connecting the Digital Keyboard to your computer, the driver software required to send and receive data will be installed on your computer automatically.
4. Start up your computers music software.
5. Configure the music software settings to select
one of the following as the MIDI device.
CASIO USB-MIDI : (For Windows Vista, Mac OS X) USB Audio Device : (For Windows XP) For information about how to select the MIDI device, see the user documentation that comes with the music software you are using.

Navigate Channels

The navigate channels can be used to display only the notes of a particular channel (part) as on-screen guide information from among the note information of a tune sent from the computer.
Specifying the Navigate Channels
From among the 16 available channels (numbered 01 to 16), you can specify any two neighboring channels (such as 05 and 06) as navigate channels. The smaller numbered channel is the navigate (L) channel, while the larger numbered channel is the navigate (R) channel. Specifying the navigate (R) channel will automatically configure the navigate (L) channel as well.
Be sure to turn on the Digital Keyboard first before starting up your computers music software.
Once you are able to connect successfully, there is no problem with leaving the USB cable connected when you turn off your computer and/or Digital Keyboard. This Digital Keyboard conforms to General MIDI Level 1 (GM). For detailed specifications and connections that apply to MIDI data send and receive by this Digital Keyboard, see the latest support information provided by the website at the following URL. http://world.casio.com/

and [6] (

) ) keys to display MIDI (page E-6).
to display Navi. Ch. ) and [6] ( ) keys

MIDI Settings

Keyboard Channel
A keyboard channel is the channel used for sending Digital Keyboard data to a computer. You can select the channel you want for sending Digital Keyboard data to a computer. The keyboard channel setting range is 01 to 16.

Na v i. Ch

4. Use the br (10-key) to specify the navigate (R)

channel.

This also will automatically configure the next lower channel number as the navigate (L) channel.

Ke y bd Ch

3. Use the br (10-key) [] and [+] keys to change

the keyboard channel.

Data Types Supported for Data Transfer
The same types of data that you can store to or recall from an SD memory card (page E-59) can be transferred to and from the Digital Keyboard. Note, that recorded song data can be transferred to a computer in the Digital Keyboards native format only. You cannot save recorded song data to a computer as a standard MIDI file (SMF format). With the CTK-5000 (only), you can save and recall scale memory data.

Downloading Data Manager

1. Go to the CASIO WORLDWIDE site at the

following URL.

http://world.casio.com/
2. At the site, select a geographic area or country. 3. After accessing the area site, navigate to the
minimum computer system requirements for Data Manager for this product.
You should be able to find a link to Data Manager information on the product introduction page of this product. If you cannot find such a link, use the search form of the area site where you are located to enter the model name of this product and search for it. Note that site contents are subject to change without notice.
4. Check if your computer system complies with
the minimum requirements for Data Manager.
5. Download Data Manager and its users guide to
6. Follow the procedure in the users guide that
you downloaded in step 5 to install and use Data Manager.
You can download accompaniment data from the Internet Data Expansion system of the CASIO MUSIC SITE (http://music.casio.com/) and load it into the memory of this Digital Keyboard. Note that there is not any accompaniment data intended specifically for this model, so you should use data for other models.
Connecting to Audio Equipment
This Digital Keyboard can be connected to commercially available stereo, amplifier, or recording equipment, to a portable audio player or other equipment.
Playing an External Device from the Digital Keyboard
Connection requires commercially available connecting cords, supplied by you. The connecting cords should have a stereo mini plug on one end and a plug that matches the configuration of the external device on the other end.
Outputting Keyboard Notes to Audio Equipment
Connection requires commercially available connecting cords, supplied by you.
Turn off the external device when making connections. After connecting, turn down the Digital Keyboard and external device volume levels whenever turning power on or off. After connecting, turn on the Digital Keyboard and then the external device. If keyboard notes sound distorted when they are sounded from external audio equipment, lower the Digital Keyboards volume setting.
Turn off the Digital Keyboard when making connections. After connecting, turn down the Digital Keyboard and external device volume levels whenever turning power on or off. After connecting, turn on the external device and then the Digital Keyboard. If notes are distorted when they are sounded on the external device, lower the volume setting of the external device.

Check and adjust the accompaniment volume setting (page E-40). Check and adjust the song volume (page E-28). Turn power off and then back on to initialize all Digital Keyboard settings (page E-9).

Specifications

Models Keyboard Touch Response Maximum Polyphony Tones Built-in Tones Sampling Tones Functions Reverb Chorus Metronome Beats per Measure Tempo Range Song Bank Built-in Songs User Songs Step Up Lesson Lessons Lesson Part Functions Music Challenge Auto Accompaniment Built-in Rhythms User Rhythms Registration Recorder Keyboard Play Playing Along with a Built-in Songs Memory Capacity Other Functions Transpose Octave Shift Tuning Scale Tuning Music Preset One Touch Preset Auto Harmonize Arpeggiator MIDI Musical Information Function Pitch Bend Wheel (CTK-5000 only) Pitch Bend Range SD Memory Cards (CTK-5000 only) Supported SD Memory Cards Functions 2GB or less SMF playback, file storage, file recall, file delete, card format
CTK-4000 / CTK-standard-size keys 2 types, Off 48 notes (24 for certain tones) CTK-4000: 570 CTK-5000: 670 Up to 8 (Melody Sampling: 5, Drum Sampling: 3)* Up to 10 seconds Layer, Split 1 to 10, Off 1 to 5, Off 0, 2 to to Up to 10* 4 (Listen, Watch, Remember, Auto) L, R, LR Repeat, Voice Fingering Guide, Note Guide, Performance Evaluation 20 notes CTK-4000: 180 CTK-5000: 200 Up to 10 (Accompaniment Edit)* 32 (4 setups 8 banks) Real-time recording, playback 5 songs, 6 tracks 1 song (L, R, LR) Approximately 12,000 notes (total for 6 songs) 1 octaves (12 to +12 semitones) Upper/Lower 2 octaves A4 = approx. 440 Hz 100 cents Scale Fine Tune (CTK-5000 only), Quarter Tone (CTK-5000 only), Preset Scales 305 CTK-4000: 180 CTK-5000: types 90 types 16 multi-timbre received, GM Level 1 standard Tone, Rhythm, Song Bank, numbers and names; staff notation, fingering, pedal operation, tempo, measure and beat number, chord name, etc. 0 to 12 semitones
Inputs/Outputs USB port Sustain/Assignable jack TYPE B
Phones/Output jack (CTK-4000) Stereo standard jack Output Impedance: 200, Output Voltage: 4.5V (RMS) MAX Phones jack (CTK-5000) Line Out R, L/MONO jacks (CTK-5000 only) Audio In jack Power Jack Power Supply Batteries Battery Life AC Adaptor Auto Power Off Speakers Power Consumption Dimensions Weight Stereo standard jack Standard jack 2 Output Impedance: 2.3k, Output Voltage: 1.5V (RMS) MAX Stereo mini jack Input Impedance: 9k, Input Sensitivity: 200mV CTK-4000: 9V DC CTK-5000: 12V DC 2-way 6 D-size zinc-carbon batteries or alkaline batteries CTK-4000: Approximately 5 hours continuous operation on zinc-carbon batteries CTK-5000: Approximately 4 hours continuous operation on alkaline batteries CTK-4000: AD-5 CTK-5000: AD-12 Approximately 6 minutes after last key operation (Operates during battery use only) CTK-4000: 12cm 2 (Output: 2.5W + 2.5W) CTK-5000: 12cm 2 + 3cm 2 (Output: 6.0W + 6.0W) CTK-4000: 9V = 7.7W CTK-5000: 12V = 18W 95.0 37.6 13.0 cm (37 7/13/1/8 inch) CTK-4000: Approximately 4.6kg (10.1 lbs) (without batteries) CTK-5000: Approximately 5.4kg (11.9 lbs) (without batteries)

MA0811-B Printed in China CTK4000/5000ES1B

Music Data Management Software

Data Manager

for Windows

Users Guide

Use this manual in combination with the User fs Guide that comes with the Instrument.

DATAMANAGERE1C

Contents

Introduction...3

What is Data Manager?.... 3 Minimum Computer Operating Environment... 4 Precautions..... 5
Getting Ready....6 Using Data Manager..7
Starting Up and Quitting Data Manager... 7 Operation Window and Data Folders.... 8 Saving Instrument Data to a PC... 12 Copying PC Data to the Instrument.... 13 Deleting Instrument Data.... 14

Error Messages....15

Introduction

What is Data Manager?

Data Manager is music data management software that you can run on your PC to perform the following three tasks. Save Instrument* data to a PC (page 12). Copy PC data to the Instrument* (page 13). Delete Instrument* data (page 14). * Instrument in this Users Guide refers to one of the following CASIO electronic musical instruments.
CTK-4000, CTK-5000, LK-205, LK-270, WK-200, WK-210, WK-500, CDP-200R
Data Manager does not support saving of songs added to the Instruments Song Bank (User Songs) to a PC. Do not use other applications or disconnect the USB cable while Data Manager is running. Doing so not only will cause Data Manager to operate abnormally, it also can corrupt data and cause malfunction of the Instrument and/or your PC.
Minimum Computer Operating Environment

Operating System

Windows XP (SP2 or later) Windows Vista

Display Settings

Resolution : pixels or greater Color : Medium (16 bit) or greater
The above minimum environment does not guarantee proper operation of this software.

Precautions

All rights to the software that accompanies this documentation (Software) revert to CASIO COMPUTER CO., LTD. (CASIO). You are not allowed to modify this Software either in part or its entirety without permission from CASIO. Distribution of any version of this Software created by altering the structure, content, or any other aspect of the original Software is prohibited. This Software is provided as is, and CASIO makes no express warranty concerning the suitability of the Software functions for any particular purpose. In no event shall CASIO be liable for any damages whatsoever (including, without limitation, damages for loss of profits, business interruption, loss of information) arising out of the use of or inability to use this Software, even if CASIO has been advised of the possibility of such damages. You are granted the right to use this Software free of charge. You are also granted the right to distribute this Software freely, as long as such distribution is not for profit. Note that CASIO will not provide any support for this Software or its functions. The contents of this Software are subject to change without notice. Actual PC screen contents may differ from the screen shots shown in this manual.

Getting Ready

1. Connect the Instrument to your PC in accordance with the instructions in the Instruments users guide.
Be sure to follow the instructions in the Instruments users guide carefully. Incorrect connections can make data copy and save impossible. Connect only one Instrument at a time. Data Manager will not operate correctly if multiple Instruments are connected.
2. Download the Data Manager software file from the CASIO website to your PCs hard disk. 3. Double-click the file you downloaded.
This will expand the compressed file and create a file named CASIO DataManager50 on your PCs hard disk. This completes the preparation phase for running Data Manager.

Using Data Manager

Starting Up and Quitting Data Manager

To start up Data Manager

1. Make sure that none of the following operations are being performed on the Instrument before starting up Data Manager.
Also, never perform any of the following operations while a data communication operation is being performed between your PC and the Instrument. Data copy, save, and delete with Data Manager will not be possible if any of the following operations are being performed on the Instrument. Record operation (Recorder) Auto Accompaniment editing operation Sampling operation Split point change operation SD memory card save, copy, or delete operation
2. Quit all other applications running on your PC.
Data Manager will not run correctly if any other application is running on your PC.
3. Double-click the folder named CASIO DataManager50 (page 6).
This will open the folder.

4. Inside the folder, double-click DataManager.exe.
This will start up Data Manager and display its operation window.
Starting up Data Manager will create a setup file in the same location as DataManager.exe. Make sure to keep the setup file in the same location as DataManager.exe. Storing them in different locations will cause Data Manager operation problems.

To exit Data Manager

Click the close () button in the upper right corner of the window, or select the Exit command on the File menu.
Operation Window and Data Folders

Operation Window

(1) Title bar
Clicking the close () button on the right side of the title bar will exit Data Manager.

(2) Menu bar

Click File 3 Preference to display the data folder (page 11) preference dialog box. Click File 3 Exit to exit Data Manager.
(3) Data type selection box
Click the down arrow button and then select the data type from the list that appears. The data types available for selection depend on the Instrument model that is connected. See note *2 under Data Types on page 10.

(4) Memory capacity bar

Shows how much of the Instruments memory has been used. The title of this bar changes in accordance with the memory area whose capacity is shown. When the title is Shared Memory Capacity: Memory bar shows the capacity of the memory area that shared for storage of sampled sounds, user songs, and user rhythms. When the title is Recorder Memory Capacity: Memory bar shows the capacity of the memory area for storage of songs recorded on the Instrument.

(5) PC toolbar

: Reload button Click this button to refresh the PC data file list (6) with the newest information.

(6) PC data file list

This is a list of the data stored in the PC data folder (page 11). See Data Types on page 10 for information about the meanings of the icons that appear to the left of the file names.

(7) Instrument toolbar

This toolbar shows the model name of the connected Instrument (WK-500 in the sample) on the left. The following describes the functions of the two buttons on the right. : Delete button Use this button to delete (page 14) the data selected in the Instrument data file list (8) from Instrument memory. : Reload button Click this button to refresh the Instrument data file list (8) with the newest information.
(8) Instrument data file list
This is a list of the user data stored in Instrument memory. See Data Types on page 10 for information about the meanings of the icons that appear to the left of the file numbers. The SMF (Standard MIDI File) file name (up to eight characters) is displayed here when copying an SMF from your PC to Instrument memory.

(9) Protect mark area

P is displayed in this area for any user area in Instrument memory that is protected.

(10) Copy (

) button
Copies the data selected in the PC data file list (6) to Instrument memory (page 13).

(11) Save (

Saves the data selected in the Instrument data file list (8) to your PC (page 12).
(12) Data folder path bar
Shows the location of the data folder (page 11) on your PC.

Data Types

Listing (Icon and Name) USER RHYTHM USER SONG RECORDED SONG RECORDED SONG (PLAY-ALONG) SAMPLED SOUND (MELODY) SAMPLED SOUND (DRUM) REGISTRATION USER SCALE MEMORY ALL DATA User rhythms*2 User songs Recorded songs*1 Songs recorded along built-in song play*1 Sampled melody sounds Sampled drum sounds Registration setups*1 *2 User scales*2 All data*1 Data Type
*1 : This data can be copied only to the same model Instrument that originally created the data. Registration data created with a CTK-5000, for example, can be copied to a CTK-5000 only. *2 : When an Instrument model that does not support a particular type of data is connected, the unsupported data type is indicated in the data type selection box as shown below. Never try to select an unsupported data type. Example: When a model that does not support storage of user scales is connected
Indicates a non-supported data type.

Data Folder

The data folder is the location on your PC that contains the data to be copied to Instrument memory using Data Manager. The initial default data folder is the CASIODataManagerData located inside the CASIO DataManager50 folder (page 6). Always make sure that any data you plan to copy to Instrument memory is located in the current data folder. Note, however, that any data stored in a folder inside the current data folder will not be available for copying.
To change the data folder
1. On the operating window menu bar, click File 3 Preference.
2. Click the [Browse.] button.
3. Select the folder (and drive if necessary) that you want to be the new data folder, and then click [OK]. This will close the dialog box.
If you want to close the dialog box without changing the data folder, click the [Cancel] button instead. Select a folder and drive whose path* contains only the characters shown in the table under step 4 on page 12. * Character string that indicates a location on a PC. The Data Folder path is shown on the Preference dialog box.
4. On the Preference dialog box that appeared in step 1 of this procedure, click the [OK] button to close the dialog box.

If you want to close the dialog box without changing the data folder, click the [Cancel] button instead.
Saving Instrument Data to a PC
Use the procedure below to save user data* from Instrument memory to your PC. * Sampled sounds and recorded songs. See the users guide that comes with the Instrument for details.
1. On the Data Manager operation window, use the data type selection box to select the type of data you want to save.
Note that user songs (songs added to the Song Bank) cannot be saved to a PC. Never try to select user songs as the data type here.
2. Use the Instrument data list to select data you want to save.
Select only one data item. Data items can be saved one-by-one only.
3. On the Data Manager operation window, click the save (
This causes the File Name: dialog box to appear.

) button.

4. Enter the file name to assign to the data when it is stored on your PC.
The following characters are supported for input in a file name.

0 a k u E O Y {

b c l m v w F G P Q Z S } @

3 d n x H R & ~

4 e o y I S _ `

5 f p z J T '

6 g q A K U (
9 h i j r s t B C D L M N V W X ) - ^
Use only the characters shown above. Inputting any character other than those above will result in malfunction of the saved data (file) when it is copied to Instrument memory.
5. Select the location (folder and/or drive) on your PC where you want to save the data.
Select a folder and drive whose path* contains only the characters shown in the table under step 4, above. * Character string that indicates a location on a PC.
6. On the File Name: dialog box, click the save ( PC.
) button to start save of the data to your
Do not operate the Instrument or disconnect the USB cable while data save is in progress. Doing so can corrupt data stored on your PC. Do not operate the Instrument while the File Name: dialog box is displayed.
Refer to page 15 if an error (ERROR) occurs during this operation.
Copying PC Data to the Instrument
Use the procedure below to copy data (file)*1 stored on your PC to the user area*2 in Instrument memory. *1 : Instrument user data that has been saved to the PC for storage, standard MIDI file (SMF), etc. See the users guide that comes with the Instrument for details. *2 : Sampled sound, user song, or other numbered location in Instrument memory for storage of user data. See the users guide that comes with the Instrument for details.
1. Move the data you want to copy to Instrument memory to the data folder (page 11).
Use only the characters shown in the table under step 4 on page 12 for a data file name.
2. On the Data Manager operation window, use the data type selection box to select the type of data you want to copy. 3. On the Data Manager operation window, click the data you want to copy.

Select only one data item. Data items can be copied one-by-one only. Never try to select any data whose name is dimmed in the PC data file list. Such data cannot be copied because it is corrupted, etc.
4. On the Instrument data list, click the user area in Instrument memory you want to use as the copy destination.
Never try to select a user area if it has a P mark (page 9), which indicates it is protected. Either unprotect the user area or select a different one.
5. On the Data Manager operation window, click the copy (
This starts data copy to the Instrument.
The confirmation dialog box shown below will appear if the copy destination user area already contains data. Note that if you overwrite existing data, it will be deleted and cannot be recovered. If you want to overwrite the existing data with the new data, click the [OK] button.
Do not operate the Instrument or disconnect the USB cable while data copy is in progress. Doing so can corrupt data stored on the Instrument.
If you advance to step 5 in the above procedure without selecting a user area in step 4, the lowest numbered user area will be selected automatically as the copy destination. Refer to page 15 if an error (ERROR) occurs during this operation.

Deleting Instrument Data

Use the following procedure to use Data Manager to delete user data in Instrument memory.
1. On the Data Manager operation window, use the data type selection box to select the type of data you want to delete.
Note that only the data shown below can be deleted. Never try to select any other type of data for deletion. USER RHYTHM USER SONG RECORDED SONG RECORDED SONG (PLAY-ALONG) SAMPLED SOUND (MELODY) SAMPLED SOUND (DRUM)
2. Use the Instrument data list to select data you want to delete.
You can select multiple data items, if you want. Never try to select a user area if it has a P mark (page 9), which indicates it is protected. Such areas are protected against deletion.
3. On the operation window Instrument toolbar, click the [Delete] button.
This will delete the selected data from Instrument memory. Note that once data is deleted, it cannot be recovered. Double-check the data you have selected for deletion before clicking the [Delete] button.
Do not operate the Instrument or disconnect the USB cable while data deletion is in progress. Doing so can corrupt data stored on the Instrument.

Error Messages

The following table tells you what you need to do whenever the ERROR dialog box appears. Corrective action depends on the error text in the dialog box. Example: Already Started error

Message

Message Already Started Cant create Data Folder: *******

Cause You are trying to start up Data Manager while it is already running. The data folder cannot be created in the location specified by *******. A file cannot be created for data storage at the location you specified on your PC.
Required Action Use the instance of Data Manager that is already running. Make sure the DataManager.exe file is in a location on your PC where new folder creation is enabled (page 7). Check if the location you specified is writedisabled. If it is, change it to write-enabled or select a different location. Check the specified path to make sure it contains only the allowed characters (page 12 step 5).
Cant create the File: *******
Cant open the File: ******* Disk Full
The file you selected (named *******) cannot be opened. The location on your PC where you are trying to save data is full.
Check if the file is being used by another application. If it is, exit the other application. Delete some of the data at the location to make room for new data. Select a different location on your PC to save the data.

Memory Full

1. Remaining available Instrument memory is low.
1. Delete some or all user data from memory to make room for new data. If Shared Memory Capacity is displayed in the memory capacity bar (page 8) when this message appears, try deleting some no longer needed sampled sounds, user songs, or user rhythms. If Recorder Memory Capacity is displayed in the memory capacity bar (page 8) when this message appears, delete some songs recorded with the Instrument.
2. The song data you are trying to copy is larger than the maximum capacity of Instrument memory.
2. Reduce the size of the data being copied to Instrument memory to the maximum allowable size for song data: Approximately 320 kb.

Message No Data

Cause 1. You are attempting to save data to your PC while a user area that does not contain any data is selected on the Instrument. 2. You are attempting to copy data to the Instrument while a file that does not contain any data (Size: 0) is selected on your PC.
Required Action 1. Select a user area that contains data.
2. Select a different file. Files of size 0 cannot be copied to the Instrument.

No Response

Data copy and save are not possible for some reason.
Check to make sure that the Instrument and PC are connected correctly. See the users guide that comes with the Instrument for details about connection. See step 1 under To start up Data Manager on page 7. If the Instrument is connected to your PC via a USB hub, connect directly without going through the hub.

No Selected Data

You are attempting to save data to your PC while there is no Instrument data selected. You are attempting to copy data to Instrument memory while there is no data (file) selected on your PC. The PC data file list (6) on the Data Manager operation window is not refreshed with the newest information. A setup file (page 7) cannot be created or written to the disk for some reason. You are trying to copy data to an Instrument user area that is protected.

Select some data (page 12).

No Selected File

Select data (a file) (page 13).

Reload And Try Again

On the Data Manger operation window, click the [Reload] button on the PC toolbar (page 8) and then try again. Correct the problem (enable writing, increase capacity, etc.) so a setup file can be created or written in the same location as DataManager.exe (page 7). Unprotect the user area. See the users guide that comes with the Instrument for details. Select a different (unprotected) user area.

Setup Error

Protected Data

MA0903-C