DW625E

ENGLISH

ROUTER DW625E

Congratulations!

You have chosen a DEWALT Power Tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional Power Tool users. Denotes risk of electric shock.
EC-Declaration of conformity

Table of contents

Technical data EC-Declaration of conformity Safety instructions Package contents Description Electrical safety Mains plug replacement (U.K. & Ireland only) Using an extension cable Assembly and adjustment Instructions for use Maintenance Guarantee en - 1 en - 1 en - 2 en - 3 en - 3 en - 3 en - 3 en - 4 en - 4 en - 6 en - 6 en - 7
DW625E DEWALT declares that these Power Tools have been designed in compliance with: 89/392/EEC, 89/336/EEC, 73/23/EEC, EN 50144, EN 55104, EN 55014, EN 61000-3-2 & EN 61000-3-3. For more information, please contact DEWALT at the address below, or refer to the back of the manual. Level of sound pressure according to 86/188/EEC & 89/392/EEC, measured according to EN 50144:
DW625E LpA (sound pressure) dB(A)* dB(A) LWA (acoustic power)

Technical data

Voltage (U.K. & Ireland only) Power input Power output No load speed Router carriage Router carriage stroke Revolver depth stop Collet size Cutters diameter, max. Weight Fuses: Europe U.K. & Ireland V V W W min-1 DW625E 230 230/115 1,850 1,100 8,000 - 20,000, infinitely variable 2 columns 62 3-step, with graduation and fine adjustment 1/5.2

* at the operators ear

Take appropriate measures for the protection of hearing if the sound pressure of 85 dB(A) is exceeded. Weighted root mean square acceleration value according to EN 50144:

DW625E < 2.5 m/s2

inch mm kg
Director Engineering and Product Development Horst Gromann

230 V tools 230 V tools

10 Amperes, mains 13 Amperes, in plugs
The following symbols are used throughout this manual: Denotes risk of personal injury, loss of life or damage to the tool in case of nonobservance of the instructions in this manual.
DEWALT, Richard-Klinger-Strae 40, D-65510, Idstein, Germany

en - 1

ENGLISH Safety instructions
When using Power Tools, always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions before attempting to operate this product. Keep these instructions in a safe place! General 1 Keep work area clean Cluttered areas and benches can cause accidents. 2 Consider work area environment Do not expose Power Tools to humidity. Keep work area well lit. Do not use Power Tools in the presence of inflammable liquids or gases. 3 Guard against electric shock Prevent body contact with earthed surfaces (e.g. pipes, radiators, cookers and refrigerators). For use under extreme conditions (e.g. high humidity, when metal swarf is being produced, etc.) electric safety can be improved by inserting an isolating transformer or a (FI) earth-leakage circuit-breaker. 4 Keep children away Do not let children come into contact with the tool or extension cord. Supervision is required for those under 16 years of age. 5 Extension cords for outdoor use When the tool is used outdoors, always use extension cords intended for outdoor use and marked accordingly. 6 Store idle tools When not in use, Power Tools must be stored in a dry place and locked up securely, out of reach of children. 7 Dress properly Do not wear loose clothing or jewellery. They can be caught in moving parts. Preferably wear rubber gloves and non-slip footwear when working outdoors. Wear protective hair covering to keep long hair out of the way. 8 Wear safety goggles Also use a face or dust mask in case the operations produce dust or flying particles. 9 Beware of maximum sound pressure Take appropriate measures for the protection of hearing if the sound pressure of 85 dB(A) is exceeded.

en - 2

10 Secure workpiece Use clamps or a vice to hold the workpiece. It is safer and it frees both hands to operate the tool. 11 Do not overreach Keep proper footing and balance at all times. 12 Avoid unintentional starting Do not carry the plugged-in tool with a finger on the switch. Be sure that the switch is released when plugging in. 13 Stay alert Watch what you are doing. Use common sense. Do not operate the tool when you are tired. 14 Disconnect tool Shut off power and wait for the tool to come to a complete standstill before leaving it unattended. Unplug the tool when not in use, before servicing or changing accessories. 15 Remove adjusting keys and wrenches Always check that adjusting keys and wrenches are removed from the tool before operating the tool. 16 Use appropriate tool The intended use is laid down in this instruction manual. Do not force small tools or attachments to do the job of a heavy-duty tool. The tool will do the job better and safer at the rate for which it was intended. Warning! The use of any accessory or attachment or performance of any operation with this tool, other than those recommended in this instruction manual may present a risk of personal injury. 17 Do not abuse cord Never carry the tool by its cord or pull it to disconnect from the socket. Keep the cord away from heat, oil and sharp edges. 18 Maintain tools with care Keep the tools in good condition and clean for better and safer performance. Follow the instructions for maintenance and changing accessories. Inspect the tool cords at regular intervals and, if damaged, have them repaired by an authorized DEWALT repair agent. Inspect the extension cords periodically and replace them if damaged. Keep all controls dry, clean and free from oil and grease. 19 Check for damaged parts Before using the tool, carefully check it for damage to ensure that it will operate properly and perform its intended function.

Check for misalignment and seizure of moving parts, breakage of parts and any other conditions that may affect its operation. Have damaged guards or other defective parts repaired or replaced as instructed. Do not use the tool if the switch is defective. Have the switch replaced by an authorized DEWALT repair agent. 20 Have your tool repaired by an authorized DEWALT repair agent This Power Tool is in accordance with the relevant safety regulations. To avoid danger, electric appliances must only be repaired by qualified technicians. Additional safety rules for cutters Always use cutters with a shank diameter corresponding to the size of the collet installed in your tool. Always use cutters suitable for a speed of 30.000 min-1 and marked accordingly. Never use cutters with a diameter exceeding the maximum diameter indicated in the technical data. 7 Threaded spindle 8 Stop 9 Knurled nut 10 Grip 11 Handwheel 12 Measuring lens 13 Scale 14 Plunge lock 15 Clamping screw 16 Depth stop 17 Fine adjuster for depth stop 18 Fine adjuster for parallel fence 19 Parallel fence 20 Revolver depth stop 21 Router base 22 Baseplate extension 23 Guiding knob

Electrical safety

The electric motor has been designed for one voltage only. Always check that the power supply corresponds to the voltage on the rating plate. Your DEWALT tool is double insulated in accordance with EN 50144; therefore no earth wire is required.

Package contents

The package contains: 1 Router 1 Parallel fence with fine adjustment and guide rods 1 Spanner # Dust extraction adapter 1 Guide bush 1 Instruction manual 1 Exploded drawing Check for damage to the tool, parts or accessories which may have occurred during transport. Take the time to thoroughly read and understand this manual prior to operation.
Mains plug replacement (U.K. & Ireland only)
Should your mains plug need replacing and you are competent to do this, proceed as instructed below. If you are in doubt, contact an authorized DEWALT repair agent or a qualified electrician. Disconnect the plug from the supply. Cut off the plug and dispose of it safely; a plug with bared copper conductors is dangerous if engaged in a live socket outlet. Only fit 13 Amperes BS1363A approved plugs fitted with the correctly rated fuse (1). The cable wire colours, or a letter, will be marked at the connection points of most good quality plugs. Attach the wires to their respective points in the plug (see below). Brown is for Live (L) (2) and Blue is for Neutral (N) (4). Before replacing the top cover of the mains plug ensure that the cable restraint (3) is holding the outer sheath of the cable firmly and that the two leads are correctly fixed at the terminal screws.

Description (fig. A)

Your DEWALT high performance Router has been designed for professional heavy duty routing of wood, wood products and plastics. 1 Lock-on button 2 Speed control dial 3 Collet nut 4 Spindle lock 5 Parallel fence locking bolt 6 Guide rods for parallel fence

en - 3

ENGLISH Assembly and adjustment
Prior to assembly and adjustment always unplug the tool. Inserting and removing a cutter (fig. B) Press and hold down the spindle lock (4). Using the 22 mm wrench, loosen the collet nut (3) a few turns and insert a cutter (24). Tighten the collet nut and release the spindle lock (4). Never tighten the collet nut without a cutter in the collet. Replacing the collet (fig. C) Your DEWALT Router is supplied with a 1/2" collet fitted to the tool. Other precision collets are also available to suit the cutter used. Separate the collet (25) from the collet nut (3) by pulling it firmly. Click the new collet in place. Setting the electronic speed control dial (fig. A) The speed is infinitely variable from 8,000 to 20,000 min-1 using the electronic speed control dial (2) for uniform cutting results in all types of wood and plastics. Turn the electronic speed control dial to the required level. The correct setting, however, is a matter of experience. 1 = 8,000 min-= 12,000 min-= 16,000 min-= 18,000 min-= 20,000 min-1 Adjusting the depth of cut (fig. A) Your DEWALT Router is equipped with a high precision depth adjustment system including a revolver depth stop (20), a measuring lens (12) and fine adjuster (17). Quick adjustment (fig. A & D) Loosen the plunge lock (14) by pulling it up. Lower the router carriage until the cutter is in contact with the workpiece. Tighten the plunge lock (14) by pushing it down.
Never use a light socket. Never connect the live (L) or neutral (N) wires to the earth pin marked E or. For 115 V units with a power rating exceeding 1500 W, we recommend to fit a plug to BS4343 standard.

Using an extension cable

If an extension cable is required, use an approved extension cable suitable for the power input of this tool (see technical data). The minimum conductor size is 1.5 mm2. When using a cable reel, always unwind the cable completely. Also refer to the table below.
Conductor size (mm2) 0.75 1.00 1.50 2.50 4.00 Cable rating (Amperes) 25 Cable length (m) 7.Voltage 115 Amperes 0 - 2.0 2.1 - 3.4 3.5 - 5.0 5.1 - 7.0 7.1 - 12.0 12.1 - 20.- 2.0 2.1 - 3.4 3.5 - 5.0 5.1 - 7.0 7.1 - 12.0 12.1 - 20.0 Cable rating (Amperes) 20 -

en - 4

For optimum ease of operation, the carriage return can be adapted to the required depth of cut by rotating or sliding the knurled nut (9). Loosen the clamping screw (15). Rotate the handwheel (11) until the fine adjuster (17) touches the revolver depth stop (20). Set the measuring lens to a round figure (e.g. 0). Adjust the depth of cut using the handwheel (11) and the measuring lens (12). The distance between the top of the revolver depth stop and the bottom of the fine adjuster is the adjusted depth of cut. Tighten the clamping screw (15). Triple depth adjustment using the revolver depth stop (fig. E) The revolver depth stop (20) can be used to set 3 different depths. This is particularly useful for deep cuts, performed in steps. Place a depth template between the fine adjuster (17) and the revolver depth stop (20) to adjust the exact cutting depth. If required, set all three screws. For installing the Router in inverted position, refer to the relevant instruction manual on the stationary tool. Fitting the parallel fence (fig. A & G) Fit the guide rods (6) to the router base (21). Slide the parallel fence (19) over the rods. Tighten the locking bolts (5) temporarily. Adjusting the parallel fence (fig. A & G) Draw a cutting line on the material. Lower the router carriage until the cutter is in contact with the workpiece. Tighten the plunge lock (14) and limit the carriage return using the knurled nut (9). Position the Router on the cutting line. Slide the parallel fence (19) against the workpiece and tighten the locking bolts (5). Adjust the parallel fence using the fine adjuster (18). The outer cutting edge of the cutter must coincide with the cutting line. If required, loosen the screws (28) holding the plastic guide strips (29) and adjust the strips to obtain the desired guiding length. Fitting the baseplate extension and trimming plate (option) (fig. A & H) When routing with large diameter cutters, it is re-commended to fit the baseplate extension (DE6268) (22) for secure handling. The trimming plate (30) is used for trimming of projecting glued edges. Fit the baseplate extension to the free end of the guide rods (6). Guide the tool with one hand on the knob (23) and the other on the opposite grip (10). For trimming projecting glued edges, fit the trimming plate (30) to the baseplate extension as shown in figure H. The trimming plate can be fitted directly next to the cutter and ensures optimim guidance. Fitting a guide bush (fig. J) Together with a template, guide bushes (DE6430) play a valuable part in cutting and shaping to a pattern. Fit the guide bush (31) to the router base (21) using the screws (32) as shown.

Make shallow cuts only! Fine adjustment (fig. F) When not using a depth template, or if the depth of cut needs readjustment, it is recommended to use the fine adjuster (17). Adjust the depth of cut using the fine adjuster (17). One turn corresponds to approx. 1 mm. Read the depth of cut using the measuring lens (12) and scale (13). Adapt the depth of cut to the millimeter using the handwheel (11). Depth adjustment with Router installed in inverted position (fig. D) Remove the cap nut (27) and the knurled knob (9) and replace it with the depth adjuster (DE6966) available as an option. Connect the threaded rod of the new depth stop to the threaded spindle (7). Set the depth of cut using the adjuster on the new depth stop.

en - 5

Connecting a dust extractor (fig. A & K) The dust extraction adapter (33) consists of a main section (34), a clamping piece (35), a cutter plate (36), two screws (37) and two nuts (38). Slide the clamping plate (35) onto the main section (34) from the front. Fit the screws (37) and nuts (38). Insert the cutter plate (36) from the bottom and rotate it until it clicks in place. Mount the unit to the router base. Connect a dust extractor hose to the dust extraction adaptor (33). Loosen the screw in the top of the router and fit the hose guide as shown. If the workpiece is not thick enough, place it on a piece of waste wood. Guiding off a batten Where an edge guide cannot be used, it is also possible to guide the router along a batten clamped across the workpiece (with an overhang at both ends). Freehand routing Your Router can also be used without any sort of guide, e.g. for signwriting or creative work. Make shallow cuts only! Use cutters with a max. diameter of 6 mm. Routing with pilot cutters (fig. B) Where a parallel guide or guide bush are inappropriate, it is possible to use pilot cutters (24) for cutting shaped edges. Consult your dealer for further information on the appropriate accessories. These include collets (1/4-1/2"), a depth stop and router table for use in inverted position, finger jointing tools for dovetail and finger jointing jigs, dowel jointing templates, guide bushes (17-40 mm), guide bushes, guide bush holders and guide rails in various lengths.

Instructions for use

Always observe the safety instructions and applicable regulations. Always move your Router as indicated in fig. L (outer edges/inner edges). Prior to operation: Check that the cutter is correctly installed in the collet. Select the optimal speed using the electronic speed control dial. Set the cutting depth. Connect a dust extractor. Make sure the plunge limiter is always locked before switching ON. Switching ON and OFF (fig. A & G) ON: pull the switch (1) UP. OFF: press the switch (1) DOWN. Loosen the plunge limiter and allow the router carriage to regain its rest position before switching OFF. Using the guide bushes (fig. J) Secure the template to the workpiece using end clamps. Select and install an appropriate guide bush (31). Subtract the diameter of the cutter from the outside diameter of the guide bush and divide by 2. This is the difference between template and workpiece.

Maintenance

Your DEWALT Power Tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning.
Lubrication Your Power Tool requires no additional lubrication.
Cleaning Keep the ventilation slots clear and regularly clean the housing with a soft cloth.

en - 6

GUARANTEE
Unwanted tools and the environment
Take your tool to an authorized DEWALT repair agent where it will be disposed of in an environmentally safe way.
30 DAY NO RISK SATISFACTION GUARANTEE
If you are not completely satisfied with the performance of your DEWALT tool, simply return it within 30 days, complete as purchased, to a participating Dealer, or an authorized DEWALT repair agent, for a full refund or exchange. Proof of purchase must be produced.
ONE YEAR FREE SERVICE CONTRACT
If you need maintenance or service for your DEWALT tool, in the 12 months following purchase, it will be undertaken free of charge at an authorized DEWALT repair agent. Proof of purchase must be produced. Includes labour and spare parts for Power Tools. Excludes accessories.

ONE YEAR FULL WARRANTY

If your DEWALT product becomes defective due to faulty materials or workmanship within 12 months from the date of purchase, we guarantee to replace all defective parts free of charge or, at our discretion, replace the unit free of charge provided that: The product has not been misused. Repairs have not been attempted by unauthorized persons. Proof of purchase date is produced. This guarantee is offered as an extra benefit and is additional to consumers statutory rights. For the location of your nearest authorized DEWALT repair agent, please use the appropriate telephone number on the back of this manual.

en - 7

PR Log - Global Press Release Distribution
#@ Discount DEWALT DW625 3-Horsepower Variable Speed - On Sale.
By Ploychun Dated: Jan 13, 2011
Get Perfect DEWALT DW625 3-Horsepower Variable Speed Electronic Plunge Router Now our most popular and top deals Shop Today!! DEWALT DW625 3-Horsepower Variable Speed Electronic Plunge Router Description : From the moment you get your hands on it, you'll appreciate the quality of this router. The handles offer total comfort and confidence as you guide this 11-1/4-pound beauty around. Its soft start means no jerking, even when you start it at its peak speed of 22,000 rpm (its bottom range is 8,000 rpm). The 15 amp motor is quieter than you'd expect in a router this size, and the rack-and-pinion The Heavy-Duty DEWALT DW625 EVS plunge router features a smooth running, powerful motor, variable speeds, and accurate depth adjuster for precise routing. The DW625's powerful 15-amp motor offers soft starts for smoother operation and variable speeds from 8,000 to 22,000 RPM. The rack and pinion depth adjuster, magnified scale, and micro-fine bit depth adjuster allow for ultra-precise routing We review the best rated and provide recommendations on where to buy online read the latest user reviews Get Perfect! Browse & Buy Online Cyber Monday Low Price on DEWALT DW625 3-Horsepower Variable Speed Electronic Plunge Router Now our most popular and top deals Lowest Price. Shop Now!.
This guide, which you should be able to request from any dealer, will walk you step by step through the process of finding the item that will meet your expectations. The buying guide will answer all the questions you have ever had about, ??? YOU CAN BUY HERE & GET BEST DEALS!! (SAVE 40% TODAY!!) steamers-lowprice.co.cc/getmo33.php?se=DEWALT+DW625+3-Horsepower&ccat=Blended Of course the first thing you must decide is what kind of item you are seeking. Once you have established this, the guide will take you through the process of finding, comparing, and purchasing of that product. It is a clever little guide that will give you all the ins and outs, of each item. They are a valuable tool, and can only make your search easier and give you good piece of mind. Its like having a friendly salesperson, giving all of their attention, to just you. As if you were the most important customer in the world. Conclusion : * Powerful, smooth-running 15 Amp motor generates 3 HP * Includes: 1/4-inch collet, 1/2-inch collet, dust extraction adapter, template guide bushing adapter, wrench * Rack and pinion depth adjuster; Magnified scale; Micro-fine bit depth adjuster for faster, more accurate bit depth settings * Base dimensions: 5-5/8 x 6-11/16 inches; weighs 11.2 pounds * Full wave electronic variable speeds between 8,000 and 22,000 RPM Shop Today DEWALT DW625 3-Horsepower Variable. Lowest Price. Shop Now!. Black Friday Deals. Discount and Reviews for How to buy DEWALT DW625 3-Horsepower Variable. Detailed research about. (Best Black Friday 2011 and Best 2011 Buy Choice. Lowest Price Guarantee!) DEWALT DW625 3-Horsepower Variable Speed Electronic Plunge Router get information on all types of products with these

Page 1/2

handy buying guides from consumer guide Fast delivery anywhere in the USA!. read the latest user reviews : DEWALT DW625 3-Horsepower Variable Speed Electronic Plunge. ??? READ FULL DETAIL. steamers-lowprice.co.cc/getmo33.php?se=DEWALT+DW625+3-Horsepower&ccat=Blended
Category Email Country Coupons, Shopping, Deals Click to email author United States

Page 2/2