Digitech RP90 - Installation, size: 2.8 MB
Hot Rod Your Tone Introducing the new RP90 from DigiTech! This guitar modeling processor is hot-rodded from the engine out. Powered by the new AudioDNA2? processor, the RP90 features your favorite boutique models including wah, stompboxes, amplifiers, cabinets, modulation effects, delays, reverbs, and special effects like DigiTechs Whammy? Aside from an arsenal of models to choose from, the RP90 features tone and effect libraries allowing you to quickly program sounds with ease. Completing the R... Read more
Part Numbers: RP90, RP90 Guitar MultiFX
UPC: 0691991201257, 691991201257
[ Report abuse or wrong photo | Share your Digitech RP90 photo ]
Digitech RP90 Multi Effects Pedal
User reviews and opinions
No opinions have been provided. Be the first and add a new opinion/review.
Modeling Guitar Processor
WARNING FOR YOUR PROTECTION PLEASE READ THE FOLLOWING:
KEEP THESE INSTRUCTIONS HEED ALL WARNINGS FOLLOW ALL INSTRUCTIONS the apparatus shall not be exposed to dripping or splashing liquid and no object filled with liquid, such as vases, shall be placed on the apparatus. CLEAN ONLY WITH A DRY CLOTH. DO NOT BLOCK ANY OF THE VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE MANUFACTURERS INSTRUCTIONS. DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT. ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED BY THE MANUFACTURER. UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or third prong are provided for your safety. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Use only with the cart stand, tripod bracket, or table specified by the manufacture, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Refer all servicing to to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. POWER ON/OFF SWITCH: The Power switch used in this piece of equipment DOES NOT break the connection from the mains. MAINS DISCONNECT: The plug shall remain readily operable. For rack-mount or installation where plug is not accessible, an all-pole mains switch with a contact separation of at least 3 mm in each pole shall be incorporated into the electrical installation of the rack or building.
DECLARATION OF CONFORMITY
Manufacturers Name: Manufacturers Address: declares that the product: Product name: Product option: DigiTech 8760 S. Sandy Parkway Sandy, Utah 84070, USA RP 90 all (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent.)
conforms to the following Product Specifications: Safety: EMC: Supplementary Information: The product herewith complies with the requirements of the Low Voltage Directive 72/23/EEC and the EMC Directive 89/336/EEC as amended by Directive 93/68/EEC. Vice-President of Engineering-MI 8760 S. Sandy Parkway Sandy, Utah 84070, USA Date: August 27, 2007 European Contact: Your local DigiTech Sales and Service Office or Harman Music Group 8760 South Sandy Parkway Sandy, Utah 84070 USA Ph: (801) 566-8800 Fax: (801) 568-7583 IEC 60065 (7th ed. 2001) EN 55013 (2001 + A1) EN 55020 (1991)
We at DigiTech are very proud of our products and back up each one we sell with the following warranty: 1. The warranty registration card must be mailed within ten days after purchase date to validate this warranty. 2. DigiTech warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship under normal use and service. 3. DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided the product is returned to DigiTech WITH RETURN AUTHORIZATION, where all parts and labor will be covered up to a period of one year. A Return Authorization number may be obtained from DigiTech by telephone. The company shall not be liable for any consequential damage as a result of the products use in any circuit or assembly. 4. Proof-of-purchase is considered to be the burden of the consumer. 5. DigiTech reserves the right to make changes in design, or make additions to, or improvements upon this product without incurring any obligation to install the same on products previously manufactured. 6. The consumer forfeits the benefits of this warranty if the products main assembly is opened and tampered with by anyone other than a certified DigiTech technician or, if the product is used with AC voltages outside of the range suggested by the manufacturer. 7. The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control. NOTE: The information contained in this manual is subject to change at any time without notification. Some information contained in this manual may also be inaccurate due to undocumented changes in the product or operating system since this version of the manual was completed. The information contained in this version of the owners manual supersedes all previous versions.
Table of Contents
Section One - Introduction
Getting Acquainted... 1. Included Items.. 1 About the RP90... 2 Performance Mode... 2 Edit Mode.. 2 . Bypass Mode.. 2. Tuner Mode... 2. Tone Library Button.. 4 Effects Library Button... 4 Effects Level Button.. 4. Master Level Button.. 4 Presets... 5 A Guided Tour of the RP90.. 6. Front Panel... 6 Rear Panel...10 Getting Started...13. Making Connections..13. Mono Operation - Amplifier..13 Stereo Operation...14. Applying Power...16
Section Three - Models and Effects
Section Two - Editing Functions
Editing/Creating Presets..17 Storing/Copying a Preset...18
About the Models...20. Model Definitions...21 Pickup/Wah...21 Compressor...22 Amp/Distortion Models..23 EQ....25 Noise Gate...25 Chorus/FX..26 Chorus...26 Flanger...27 Phaser....27 Tremolo...27. Panner....27. Vibrato...27. Rotary Speaker...27 TM YaYa...28 Auto Ya...28 Step Filter...28. Envelope Filter..28 Detune...28. Pitch Shift...28 DigiTech Whammy..29. Delay....29 Reverb...31
Section Four - Other Functions
Expression Pedal Assign..32. Drum Machine...34. Factory Reset...34. Expression Pedal Calibration..35
Section Five - Appendix
Specifications..36. Tone Library...38. Effects Library...39 Preset List...40
Disclaimer: DigiTech, Production Modeling, Grunge, Death Metal, DOD, DigiTech Whammy, Multi-Chorus,Ya Ya, Johnson Amplification and AudioDNA2 are trademarks of Harman International Industries, Incorporated in the U.S. and other countries. Fender Tweed Deluxe, Fender Blackface Twin Reverb, Fender Twin Reverb, Marshall Super Lead, Marshall Slant, Marshall Master Volume, Marshall Straight,Vox AC30, Mesa Boogie, Dunlop Cry Baby, Vox Clyde McCoy Wah, Ibanez Tube Screamer, Boss DS-1, Electro-Harmonix Big Muff are products of DigiTechs competitors and trademarks of their respective companies in the U.S. and other countries and are not associated or affiliated with DigiTech or Harman International Industries, Incorporated. 2007 Harman International Industries, Inc. All Rights Reserved.
Section 1 - Introduction
Congratulations on your purchase of the RP90. You now have an incredibly advanced modeling guitar processor that can keep up with your creative impulses and even increase them. Armed with DigiTechs patented AudioDNA2 custom audio DSP chip, the RP90 gives you a huge selection of tones and effects, right at your fingertips. When you easily select an amp or distortion tone and an effects chain from the Tone Library or the Effects Library, youll appreciate the accuracy in each model, and the dynamic interaction in each tone. Add a built-in drum machine, and you have the RP90: the key to unlock your creative potential.
Before you get started, please make sure that the following items have been included: RP90 PS200R Power Supply Warranty Card
The utmost care was taken while your RP90 was being manufactured. Everything should be included and in perfect working order. If anything is missing, contact the factory at once. Please help us become acquainted with you and your needs by completing your warranty card or registering online at www.digitech.com. It is your safeguard should a problem arise with your RP90.
About the RP90
When you first apply power to the RP90, it powers up in Performance mode. Performance mode provides access to all of the presets within the RP90 via the Up and Down Footswitches. The Edit Up/Down buttons cycle through the effects in the matrix.
When you select an Effect with the Edit Up/Down buttons, you can adjust the Effect with the Value Up/Down buttons. (For descriptions of the Effects and their parameters, see page 20.) When you make changes to a presets Effects, you must store the changes or they will be lost when you select a different preset or disconnect power to the RP90. See page 18 for a description of the Store procedure.
The RP90 presets can be bypassed for a clean, unprocessed guitar signal. To bypass the RP90, press and release both Footswitches simultaneously. The Display reads By indicating the preset is bypassed. In Bypass mode, all buttons are disabled. Press either Footswitch to exit Bypass mode and return the RP90 to the last preset used.
The Tuner in the RP90 allows you to quickly tune or check the tuning on your guitar. Enter Tuner mode by pressing and holding both Footswitches simultaneously. The Display briefly shows tu indicating that you are in Tuner mode. To begin tuning, play a note on your guitar (a harmonic at the 12th fret usually works best). The Display shows the note being played. The Matrix LEDs
indicate whether you are sharp or flat. The left 6 red LEDs indicate the note is flat and should be tuned up. The right 6 red LEDs indicate the note is sharp and should be tuned down. The center LED indicates the note is in tune. The output is muted in Tuner mode; rock the Expression Pedal to regain volume.
Center LED indicates note is in tune Display shows note played
Left LEDs indicate note is flat
Right LEDs indicate note is sharp
In Tuner mode, you can change your tuning reference with the Vallue Up/Down buttons. The default factory setting is A=440 Hz (displayed as 40). Other tuning references are A=A flat (displayed as Ab), A=G (displayed as G), and A=G flat (displayed as gb). The display window will briefly flash the currently selected tuning preference. Exit Tuner mode by pressing either Footswitch.
Tone Library Button
You can press this button at any time (except in Bypass or Tuner mode) to access the Tone Library, and then use the Value Up/Down buttons to select from a variety of genre-based amp tone defaults ranging from Blues to Metal to Country. Behind the scenes, the Compressor, Distortion, Pickup/Wah effects, Amp/Cabinet model, and EQ are configured to create a specified tone. You can further refine the sound by editing the preset (see Editing/Creating Presets on page 17). Changing between different Tone Library defaults does not change the Chorus/FX, Delay or Reverb, letting you experiment with different amp styles quickly in the context of the current effect chain.
Effects Library Button
You can press this button at any time (except in Bypass or Tuner mode) to access the Effects Library and then use the Value Up/Down buttons to select from a variety of post-amplifier model effect chains (Chorus, Chorus + Delay, Delay + Reverb, etc.).You can further refine the sound by editing the preset (see Editing/Creating Presets on page 17). Changing between different Effects Library defaults does not change the Compressor, Distortion, Amp/Cabinet model, and EQ settings, letting you experiment with different effect chains quickly in the context of the current amp tone.
Effects Level Button
You can press this button at any time (except in Bypass or Tuner mode) to access the Effects Level. This button changes the relative level of the post-amp effects (Chorus/FX, Delay, and Reverb). This can be thought of as an effects mix control, where increasing this buttons value increases the level of these effects and decreasing its value decreases the level of these effects.
Master Level Button
Press this button and use the Value Up/Down buttons to set the overall output level of the RP90.
1. Access the Tone Library with this button and select a tone with the Value buttons.
2. Access the Effects Library 3. Access the effects level with this button and select with this button and adjust the a tone with the Value buttons. level with the Value buttons.
The Tone Library button, Effects Library button, and Effects Level button make it easy to quickly load preset tones, effects, and effects chains.
To learn about storing changes to presets, see page 18. Presets
Presets are numbered locations of programmed sounds which reside in the RP90. Presets are recalled with the Footswitches. The active effects in each preset are indicated by lighted LEDs in the Effect Matrix. The RP90 comes with 50 User presets (1-50) and 50 Factory presets (51-00). The User presets are locations where your creations may be stored. The Factory presets do not allow you to store any changes to them. From the factory, the 50 User presets are exact duplicates of the 50 Factory presets. This allows you to create your own presets without losing the sounds that came with the RP90.
A Guided Tour of the RP90
These two Footswitches select presets, access the Tuner, or bypass the RP90. The Footswitch on the right will select the next preset up, and the Footswitch on the left will select the next preset down. Pressing both Footswitches together will bypass the currently selected preset. Pressing and holding both Footswitches for 2 seconds will access the Tuner. Press either Footswitch to exit Bypass or Tuner mode.
Tone Library, Effects Library, Effects Level, and Master Level Buttons
At the heart of creating presets in the RP90 are the Tone Library, Effects Library, and Effects Level buttons. By pressing one of these buttons and using the Value Up/Down buttons, you can select from 20 amp/distortion tones, 20 effects chains, or the overall post amp/distortion effects level respectively. The Master Level button accesses the master output volume parameter for the RP90. Each button is described in detail below. Tone Library Button The Tone Library button accesses a library of preset amp tones. Press this button and then use the Value Up/Down buttons to select from a variety of genre-based amp tones ranging from Blues to Metal to Country (see page 38 for a list of available tones). Behind the scenes, the Pickup/Wah, Compressor, Amp/Distortion, and EQ are configured to create a specified tone. You can further refine the sound by editing the preset (see Editing/Copying Presets on page 17). Changing between different Tone Library selections does not change the Chorus/FX, Delay, or Reverb settings, allowing you to experiment with different amp styles quickly in the context of the current effect chain. The Display will read CU (for custom) when any of the associated effects have been changed from a default library setting.
Effects Library Button The Effects Library button accesses a library of preset effect configurations. Press this button and use the Value Up/Down buttons to select a variety of post-amplifier model effect chains (Chorus, Chorus + Delay, Delay + Reverb, etc). You can further refine the sound by editing the preset (see Editing/Copying Presets on page 17). Changing between different Effects Library selections does not change the Pickup/Wah, Compressor, Amp/Distortion and EQ settings, allowing you to experiment with different effect chains quickly in the context of the current amp tone. The Display will read CU (for custom) when any of the associated effects have been changed from a default library setting. Effects Level Button The Effects Level button lets you adjust the levels of post-amp model effects (Chorus/FX, Delay, and Reverb). Press this button and use the Value Up/Down buttons to change the relative level of the post-amp effects (Chorus/FX, Delay, and Reverb). Think of it as an effects mix control where increasing this setting increases the level of these effects, while decreasing this setting decreases the level of these effects. Master Level Button The Master Level button lets you adjust the output level of the RP90. Press this button and use the Value Up/Down buttons to change the output level of the RP90.
The Edit Up/Down buttons select which effect is to be edited. As each effect is selected, the Display shows the effect setting. A decimal in the bottom right corner of the Display turns on when a preset has been modified. The Edit Up/Down buttons are also used to change the RP90 Drum Machine parameters (Note that Drum Machine settings are global for all presets and are not saved with the preset).
Value Up/Down Display
The Value Up/Down buttons are used for editing effects, navigating Tone/Effects Libraries, adjusting Effects and Master Levels, and adjusting Drum Machine settings. The Display provides information for different functions depending on the mode that has been selected. In Performance mode, the Display shows the currently selected preset number. In Edit mode, the Display shows the value of the effect being adjusted. A decimal in the bottom right corner of the Display turns on when a preset has been modified. In Tuner mode, the Display shows the note being played.
The matrix provides information regarding the current preset and Effect edit functions. In Performance mode, the LEDs next to each Effect provide a visual indication of which Effects are in use for the currently selected preset. While editing a preset, the LEDs indicate the Effect currently selected for editing. In Tuner mode, the LEDs indicate whether the note played is sharp, flat, or in tune.
The Drums button is used to turn on and off the RP90s built-in drum machine. When the Drums button is turned on, the Drums button LED lights and the selected drum pattern plays continuously. Use the Value Up/Down buttons to change the pattern of the drum machine. See page 34 for more information about the drum machine.
The Store button is used to save your changes to the User presets. See page 18 for more information about storing presets.
The Expression Pedal provides real-time control of the RP90s Volume, Wah, or the assigned effect parameter.
Input Connect your instrument to this high-impedance TS input. Amp / Mixer This button optimizes the RP90s outputs for use when plugged into a guitar amp or a mixer/recording device. When set to Mixer (In position), the outputs are optimized for connecting to a mixer, recording device or headphones. When set to Amp (Out position), the outputs are optimized for running directly in to the input of a guitar amp. Left (Mono) and Right Outputs Connect the Left (Mono) output to the input of a single amplifier (or mixer input) for mono operation. Connect the Left and Right outputs to the inputs of 2 amplifiers (or 2 mixer channels) for stereo operation.
Stereo Amp Setup
Guitar Amp Input/Effect Returns
Outputs Amp/Mixer switch set to Amp. Input
Stereo Mixer Setup
-1 -2 -3 -4 -0 -1 +2 -2 +3 -3 +4 --1 +2 -2 +3 -3 +4 -4 --1 +2 -2 +3 -3 +4 -4 --1 +2 -2 +3 -3 +4 -4 --1 +2 -2 +3 -3 +4 -4 -0 -1 +2 -2 +3 -3 +4 -4 -5
Aux 1 10
Aux 2 10
0 +1 +2
0 -1 -2 +3 -3
0 +1 +2 +3 +4
+4 -4 -5
L/R L/R L/R L/R L/R L/R L/R L/R
+10 +5 0
-20 -30 -
Amp/Mixer switch set to Mixer
Before applying power to anything, set your amp(s) to a clean tone and set the tone controls to a flat EQ response (on most amps, this would be 0 or 5 on the tone controls). Then follow the steps listed below. 1. 2. 3. 4. 5. Turn the amp volume all the way down. Connect the plug of the PS200R power supply to the power jack on the rear panel of the RP90. Connect the other end of the PS200R power supply to an AC outlet. Use the Master Level button and the Value Up/Down buttons to set the RP90s Master Level to 0. Turn the power of your amplifier(s) to the on position and adjust the volume(s) to a normal playing level. Use the Master Level button and the Value Up/Down buttons to gradually increase the RP90s Master Level to achieve the desired volume.
2. Connect PS200R to power jack 4.Turn amp volume up
3. Connect PS200R to AC outlet and set the RP90s Master Level to 0 5. Set the RP90s Master Level to the desired listening volume
1.Turn amp volume down
The RP90 is designed to make preset editing and creation easy and intuitive. When creating your own sound, you must first start with an existing preset. Note that the preset you begin with doesnt have to be in the memory location you intend to have it reside, since you can store it to any User preset location during the store procedure. The easiest way to start is by using the Tone Library and Effects Library buttons. The Tone Library button gives you access to a variety of pre-programmed amp/distortion tones (see page 38) based on different musical styles. The Effects Library button then lets you select from a palette of effects chains (see page 39), from simple delays to full multi-effect signals with modulation, delay and reverb. Use the Effects Level Button to easily increase or decrease the Chorus/FX, Delay and Reverb levels if desired. Using these three controls should get you close to a sound you are after. From there you can then use the Edit buttons to select individual Effects, and the Value Up/Down buttons to adjust their settings. To edit and create a custom preset: 1. 2. 3. Use the Footswitches to select the preset you wish to edit. If you are trying to find something different from the existing presets, begin by using the Tone Library, Effects Library, Effects Level and Value Up/Down buttons to get close to a sound you want. Once you have a sound close to what you are after, begin editing the Effects by pressing the Edit Up/Down buttons and selecting the Effect you want to adjust. To turn an Effect on, select it with the Edit Up/Down buttons. Each Effect has multiple settings to select from. Use the Value Up/Down buttons to change the values for the selected Effect To turn an Effect off, press and hold the Value Down button until Ofappears in the Display. (For EQs, b5, d5, and t5 are the settings with no boost or cut.)
Anytime a stored value within a preset is changed, you need to store the changes (with the Store button), or the changes will be lost. Changing presets, or turning the power off before storing any changes erases any edits made and the RP90 will revert to the stored values for the preset.
Storing/Copying a Preset
Once the preset has been modified to your liking, you may store your settings to any of the 50 User preset locations (presets 1-50). The following steps outline the procedure for storing changes to a preset or copying a preset to a different location: 1. 2. 3. Press the Store button once and the current Preset location will flash in the Display. This is asking you to select a new User Preset location where your new sound will reside. If desired, select a new User Preset location using the Footswitches. Press the Store button again to save the changes.
The procedure for copying one Preset to another Preset location is the same. Simply use the Footswitches to select the Preset that you want to copy, then follow the steps listed above.
1. Press the Store button; the Preset number flashes. 3. Press the Store button again to save your changes.
2. Select a destination with the Footswitches.
About the Models
The RP90 can be thought of as several different virtual amplifiers and individual, high-tech stompboxes in a single programmable package. With stompboxes, the order in which they are connected affects the overall sound. The RP90 has placed the Amp and Effect models in an order for optimum results. The following diagram shows the order in which they are connected.
Volume Pedal (Pre)
Volume Pedal (Post)
Each Amp and Effect model within the RP90 has multiple settings to select from. Use the Value Up/Down buttons to change the values for the selected Effect. The following overview of the RP90s Effects outlines the settings each Effect contains.
The Pickup Simulator provides the thick tone of a humbucker pickup to a guitar with single coil pickups, or the bright, edgy sound of a single coil pickup to a guitar with a humbucker. This gives you the best of both worlds without having to change guitars during a performance. Wah is an effect controlled by an Expression Pedal making the guitar sound as if its saying Wah. See page 32 on how to link the Wah effect to the Expression Pedal. The Pickup/Wah settings are: OF SH HS CB CY Fr Pickup/Wah is turned off. Makes a single coil pickup sound like a humbucker. Makes a humbucker pickup sound like a single coil. Dunlop Cry Baby TM wah model Vox Clyde McCoy TM wah Full range wah
A Compressor is used to increase sustain, tighten up guitars, and prevent the signal from clipping the input of other effects. It sets a maximum boundary for the strength of a signal. The settings for the compressor effect are: OF Compressor is turned off. 1-20 Level of compression and sustain. Ratio is set to infinity:1.
The RP90 has 12 amp and 6 distortion models to choose from. Each model is identified by a single letter and has nine settings (for example, b1 through b9), except Acoustic Guitar Simulator and Direct, which only have one setting. As the setting increases, the amp/distortion gain increases. Each amp model has a cabinet model assigned to it as shown in the following list. OF Amp/Distortion is turned off. Amp/Cabinet Models t1-t9 Based on a 57 Fender Tweed Deluxe amp with a Fender Tweed Deluxe 1x12 cabinet b1-b9 Based on a 65 Fender Blackface Twin Reverb amp with a Fender Twin Reverb 2x12 cabinet P1-P9 Based on a 68 Marshall Super Lead (Plexi) amp with a Johnson Straight Celestion Vintage 30 4x12 cabinet H1-H9 Based on a 77 Marshall Master Volume amp with a Marshall Straight Celestion G12- T70 4x12 cabinet J1-J9 Based on an 83 Marshall JCM800 amp with a Johnson Straight Celestion Vintage 30 4x12 cabinet A1-A9 Based on a 63 Vox AC30 Top Boost amp with an AC30 TB Jensen Blue Back 2x12 cabinet r1-r9 Based on an 01 Mesa/Boogie Dual RectifierTM amp with a Johnson Straight Celestion Vintage 30 4x12 cabinet C1-C9 Based on a 96 Matchless DC-30 amp with a Johnson Straight Celestion Vintage 30 4x12 cabinet O1-O9 DigiTech Solo amp model with a DigiTech Solo 4x12 cabinet model E1-E9 DigiTech Metal amp model with a DigiTech Metal 4x12 cabinet model n1-n9 DigiTech Bright Clean amp model with a DigiTech Bright Clean 4x12 cabinet model u1-u9 DigiTech Clean Tube amp model with a cabinet model based on a Fender Twin Reverb 2x12 cabinet 23
Distortion Models S1-S9 Based on Ibanez TS-9 Tube ScreamerTM o1-o9 Based on DOD 250 Preamp/Overdrive d1-d9 Based on Boss DS-1TM Distortion G1-G9 DigiTech Grunge L1-L9 DigiTech Death Metal F1-F9 Based on Electro Harmonix Big Muff Pi Other AC Acoustic Guitar simulator
The RP90s EQ helps further shape your tone with Bass, Midrange, and Treble controls. The EQ settings are: b1-b9 d1-d9 t1-t9 Bass tone control. b1-b4 cut bass frequencies by 12dB, 9dB, 6dB, and 3dB respectively. b5 has no boost or cut. b6-b9 boost bass frequencies by 3dB, 6dB, 9dB, and 12dB respectively. Midrange tone control. d1-d4 cut midrange frequencies by 12dB, 9dB, 6dB, and 3dB respectively. d5 has no boost or cut. b6-b9 boost midrange frequencies by 3dB, 6dB, 9dB, and 12dB respectively. Treble tone control. t1-t4 cut treble frequencies by 12dB, 9dB, 6dB, and 3dB respectively. t5 has no boost or cut. t6-t9 boost treble frequencies by 3dB, 6dB, 9dB, and 12dB respectively.
The Noise Gate effect includes two models: a Silencer gate and an Auto Swell gate. A silencer gate is designed to eliminate noise while you are not playing. The Silencer gates nine settings (g1-g9) determine the threshold, which determines how loud a signal must be before it can be heard. The higher the setting, the louder a signal must be in order to be heard. The Auto Swell provides an automatic volume swell effect. The auto swells nine settings (S1-S9) determine the attack time (how quickly the swell grows from the note you play). The higher the setting, the faster the swell grows. The noise gate settings are: OF Noise gate effect is turned off g1-g9 Silencer gate. g1 is the lowest threshold, g9 is the highest threshold. S1-S9 Auto Swell gate. S1 is the fastest attack time, s9 is the slowest attack time.
The Chorus/FX model actually contains twelve different modulation and pitch effects (described on the following pages). Each effect includes nine settings which include a variety of configurations that generally range from more subtle (lower settings) to more extreme (higher settings).The Chorus/FX settings are: OF c1-c9 C1-C9 F1-F9 P1-P9 t1-t9 n1-n9 b1-b9 Chorus/FX effect is turned off Boss CE-2 Chorus Dual Chorus Flanger Phaser Tremolo Panner Vibrato r1-r9 Y1-Y9 A1-A9 S1-S9 E1-E9 d1-d9 h1-h9 H1-H9 Rotary Speaker YaYa AutoYa Step Filter Envelope Filter Detune Pitch Shift DigiTech Whammy
Chorus A Chorus adds a short delay to your signal. The delayed signal is modulated in and out of tune and then mixed back with the original signal to create a thicker sound. The RP90 Chorus effect includes a model based on the classic Boss CE-2 Chorus and the Dual Chorus. Chorus settings are: c1-c9 Boss CE-2 Chorus. C1-C9 Dual Chorus.
Flanger A Flanger uses the same principle as a Chorus but uses a shorter delay time and adds regeneration (or repeats) to the modulating delay. This results in an exaggerated up and down sweeping motion to the effect. Settings are F1-F9. Phaser A phaser splits the incoming signal, and then changes the phasing of the signal. This signal is then taken in and out of phase and mixed back in with the original signal. As the phasing changes, different frequencies get canceled resulting in a warm sort of twisting sound. Settings are P1-P9. Tremolo A Tremolo effect modulates the volume of the signal at an even rate. Settings are t1-t9. Panner A Panner modulates the sound from left to right at an even rate. Settings are n1-n9. Vibrato A Vibrato effect modulates the pitch of the incoming signal at an even rate. Settings are b1-b9. Rotary Speaker Rotary Speaker is an emulation of a device that included a spinning horn and woofer. The rotation of these two speakers produced an interesting combination of the sound panning from side to side. This produced a slight pitch change due to the speed of the sound coming towards, and then going away from the listener. Settings are r1-r9.
YaYaTM AutoYa combines the characteristics of a Wah and a Flanger, creating an almost human vowel characteristic as if the guitar were saying Yah. Control the effect with the Expression Pedal. Settings are Y1-Y9. AutoYa Similar to the YaYa effect described above, AutoYa automatically provides this animation to the sound at an even rate. Settings are A1-A9. Step Filter The Step Filter is like an automatic random wah with a square waveform. Settings are S1-S9. Envelope Filter The Envelope Filter is a dynamic Wah effect that alters your sound based upon how hard you play. Settings are E1-E9. Detune A Detuner makes a copy of your incoming signal, takes the copied signal slightly out of tune from the original, then mixes the two signals together. The result is a doubling type of effect as if two guitars were playing the same part together. Settings are d1-d9. Pitch Shift A Pitch Shifter copies the incoming signal, then shifts the pitch of the copy to a different note. The shifted note is then mixed back with the original signal, sounding as if two guitars were playing different notes. Settings are h1-h9.
The Expression Pedal on the RP90 can be assigned in each preset to control the Volume, Wah, DigiTech WhammyTM,YaYaTM, or one of several other parameters in real time with your foot. The procedure for assigning a parameter to the Expression Pedal is as follows: 1. 2. 3. 4. 5. Press either Edit Up button until the Expression LED lights up. An effect LED will also light indicating which effect the Expression Pedal is currently assigned to. Press either Value Up/Down button until your desired effects LED is lit in the matrix. The Expression LED will stay lit during your selection and the Display will show a two-digit character value to describe the effect parameter that the Expression Pedal is assigned to. Once you have assigned a parameter, you can set the control range of that parameter. Press the Edit Up button again. The number value shown is the minimum parameter value this is the value that will be reached when the Expression Pedal is rocked back (toe up). Press the Edit Up button again. The number value shown is the maximum parameter value this is the value that will be reached when the Expression Pedal is rocked forward (toe down). Use the Store procedure (see page 18) to save your changes to the preset.
Expression assignments available are as follows: No Assignment Volume Volume Wah Amp Chorus Flanger Phaser Tremolo Panner Vibrato Rotary YaYa AutoYa Envelope Filter Detune Pitch Shift Whammy Delay Reverb OF Pr (Output Level Pre Delay) PS (Output Level Post Delay) AH (Expression Pedal acts as a Wah pedal) gA (Expression Pedal controls the Amp Gain) SP (Speed) LE (Level) SP (Speed) LE (Level) SP (Speed) LE (Level) SP (Speed) dP (Depth) SP (Speed) dP (Depth) SP (Speed) dP (Depth) SP (Speed) dP (Depth) Pd (Expression Pedal acts as a YaYaTM Effect when engaged) SP (Speed) dP (Depth) ES (Sensitivity) LE (Level of the Detuned signal) LE (Level of the Pitch Shifted signal) HY (Expression Pedal acts as a DigiTech WhammyTM pedal) dL (Delay Level) dF (Delay Feedback) rL (Reverb Level)
The RP90 features a built-in drum machine, which is enabled by pressing the Drums button. Select patterns, tempo, and level with the Edit Up/Down buttons. Change their values with the Value Up/Down buttons. The drum machine has the following parameters Drum Patterns Drum Tempo Drum Level 1-40 1-99 (equivalent of 40 240BPM) 0-99
Drum machine settings are globally set and not individually stored with each of the RP90s user presets.
This function resets the RP90 to its original factory settings. This procedure erases all custom User presets. ATTENTION: Performing this function will erase all user-programmed data. All such data will be lost forever! Be sure you want to erase the memory and return the RP90 to its factory default state before continuing with this procedure. The procedure for performing a Factory Reset is as follows: 1. Press and hold the Store button while powering up the RP90. 2. When the display prompts you with FR, release the Store button. 3. Press and hold the Store button for 3 seconds until RS appears in the display and release. The Factory Reset procedure takes approximately 10 seconds. 4. Once the factory reset has finished you will need to calibrate the Expression Pedal. Follow steps 2-4 on the next page to complete calibration.
Power Requirements: US and Canada: Japan: Europe: UK:
120 VAC, 60 Hz Adapter: PS200R-VAC, 50/60 Hz Adapter: PS200R-VAC, 50 Hz Adapter: PS200R-VAC, 50 Hz Adapter: PS200R-240
Tone Library Overdrive Rock Blues Metal Country Warm Drive Crunch Texas Tone Rockabilly Solo Rock Wah Chunky Smooth Heavy Clean British Distortion Scooped Bright Clean Acoustic
Effects Library Chorus Flanger Phaser Pitch Tremolo Rotary Envelope Filter Digital Delay Analog Delay Tape Delay Hall Reverb Spring Reverb Chorus + Digital Delay Chorus + Delay + Reverb Flanger + Analog Delay Phaser + Tape Delay Digital Delay + Hall Reverb Analog Delay + Spring Pitch + Room Reverb Vibrato + Tape Delay
Preset List (User/Factory)
1/51 2/52 3/53 4/54 5/55 6/56 7/57 8/58 9/59 10/60 11/61 12/62 13/63 14/64 15/65 16/66 17/67 18/68 19/69 20/70 21/71 22/72 23/73 24/74 25/75 RECTO CLEAN CHORUS BRITISH STACK TWEEDY ANALOG BOY FUNK IT WHAMMY OLD SCHOOL BIG SOLO SB - OVERDRIVE* BRITISH COMBO WAHS HAPPENING BLUES DRIVE JAZZY DRIVE SB - DISTORTION* YOU TOO COUNTRY PICKIN SB - FUZZ KING* BIG BLUES HEAVY DUTY PLEXI TIME FLANGIST DETUNED CLEAN PHASE HEAD COMPRESSED 26/76 27/77 28/78 29/79 30/80 31/81 32/82 33/83 34/84 35/85 36/86 37/87 38/88 39/89 40/90 41/91 42/92 43/93 44/94 45/95 46/96 47/97 48/98 49/99 50/00 RETRO BILLY GOOD N GREASY OCTAVED CLEAN DELAY TAPE DELAYS ACOUSTIC DA CRUSHER SB - PURPLE FUZZ* ISNT IT SWELL BLUE DELUXE CAPTAIN CRUNCH 5THS PHASE DELAY JAZZ BOX SARGENT D WARM DRIVE SB - GOOD GRUNGE* TREMOLO VERB UNPLUGGED MOSHIN MR CLEAN ANGUS VIBRO WAHNABEE PUNK
* SB = Stompbox Distortion
DigiTech 8760 South Sandy Parkway Sandy, Utah 84070 PH (801) 566-8800 FAX (801) 566-7005 http://www.digitech.com
Printed 8/2007 RP90 Owners Manual 18-0490-A
2007 Harman International Industries, Incorporated, all rights reserved. DigiTech, Production Modeling, Grunge, Death Metal, DOD, DigiTech Whammy, Multi-Chorus,Ya Ya, Johnson Amplification and AudioDNA2 are trademarks of Harman International Industries, Incorporated in the U.S. and other countries. Fender Tweed Deluxe, Fender Blackface Twin Reverb, Fender Twin Reverb, Marshall Super Lead, Marshall Slant, Marshall Master Volume, Marshall Straight,Vox AC30, Mesa Boogie, Dunlop Cry Baby,Vox Clyde McCoy Wah, Ibanez Tube Screamer, Boss DS-1, Electro-Harmonix Big Muff are products of DigiTechs competitors and trademarks of their respective companies in the U.S. and other countries and are not associated or affiliated with DigiTech or Harman International Industries, Incorporated. 2007 Harman International Industries, Inc. All Rights Reserved.
Hot Rod Your Tone Introducing the new RP90 from DigiTech! This guitar modeling processor is hot-rodded from the engine out. Powered by the new AudioDNA2? processor, the RP90 features your favorite boutique models including wah, stompboxes, amplifiers, cabinets, modulation effects, delays, reverbs, and special effects like DigiTechs Whammy? Aside from an arsenal of models to choose from, the RP90 features tone and effect libraries allowing you to quickly program sounds with ease. Completing the RP90 are 100 aggressive sounding presets that appeal to todays modern players.
Turbo-17R LN46B640r3F IC-F50 Orange WB4 DSP-AX1500 Looper Akai S900 Settings 62216 IFP-895 0I 16V ME440XE1 Demo PS50A456 Hotels Xiosynth Owners Manual HP-1800 1030SW Models Nokia 330 Reset KEH-M4000 N4504 CJ-KS7 TCP50G10 32LG4000 AEK PCG-GRZ615M Bizhub 283 421 WS ECR 5500 KX-TG4324 Corolla 2010 IC-756proii TX-28PK20F Camedia C-1 DCR-IP7 Ariete 1329 Trimble Juno 6592G Fighter 4 Guitar Center Yamaha PB1 Xperia X1 Machine-301 CVA-1004R RD-1000 42PFP5332-10 All-IN-ONE MD-X5 Wheel WD-12EFD Es90 Axis 207 I D KDC-W8531 Printer Photosmart 850 IC-F7000 Blood Perfection 3590 46WM48 ZDT200 Photosmart 8450 HFC171-05 LC5-D20BB VN-5500 P-2000W Contest PLC-XU33 Aurora 1999 Dvdr3480 58 Software RM4200 NN-K453 Axiophot IC-245 K7VZA Officejet 4219 SCE4430 IP5300 IC-H16T Patches Liebert 376 Blackberry 950 SA2640 SCH-M620 3400 W Diversion ABS Yamaha 115 W1542S-PF DCR-TRV27E SX-KN2000 DVD957 001 1250 FAX ZWG3121 Xdrive 50I CQ-DF802U MP-408 MW82Y-S Party 8 Wide View KDC-W6527 F1056QD 52 Accu Infocus IN34 Magic
manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101