ENGLISH - PAGES 4-7

READ ALL INSTRUCTIONS BEFORE OPERATING UNIT!
ESPAOL - PGINAS 8-11 LANSE ANTES DE UTILIZAR EL APARATO Y GUARDENSE PARA SU USO POSTERIOR!
FRANAIS - PAGES 12-15 PRIERE DE LIRE AVANT LEMPLOI ET A CONSERVER POUR UTILISATION ULTERIEURE!
ITALIANO - PAGINE 16-19 LEGGERE ATTENTAMENTE PRIMA DELLUSO E CONSERVARE PER UN UTILIZZO SUCCESSIV0!
DEUTSCH - SEITEN 20-23 BITTE VOR GEBRAUCH LESEN UND FR SPTEREN GEBRAUCH AUFBEWAHREN!

- 24-27

TO PREVENT DAMAGE, FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. NO USER SERVICEABLE PA RTS INSIDE, REFER SERVICING TO QUALIFIED PERSONNEL ONLY. DO NOT ALTER THE AC PLUG.
THIS UNIT MUST BE EARTH GROUNDED. UNPLUG THE AC POWER LINE CORD BEFORE CLEANING THE UNITS COVERING WITH ONLY A DAMP CLOTH; WAIT UNTIL THE UNIT IS COMPLETELY DRY BEFORE RECONNECTING IT TO POWER.
PAR A EVITAR DAOS, INCENDIOS Y DESCARG AS ELCTRICAS, NO EXPONGA ESTA UNIDAD A LA LLUVIA NI A LA HUMEDAD. CONTIENE PIEZAS CUYO MANTENIMIENTO NO LO PUEDE R EALIZAR EL USUARI O, S INO SLO PERSONAL CUALIFICADO.
NO MODIFIQUE EL ENCHUFE DE CA. ESTA UNIDAD DEBE CONECTARSE CON TOMA DE TIERRA. DESCONECTE EL CABLE DE ALIMENTACIN DE CA ANTES DE LIMPIAR LA CUBIERTA DE LA UNIDAD; ESPERE A QUE LA UNIDAD EST COMPLETAMENTE SECA ANTES DE VOLVER A CONECTARLA A LA CORRIENTE.
POUR EVITER L'ENDOMMAGEMENT DE L'APPA R E I L , UN DEPA RT D'INCENDIE, OU UN CHOC ELECTRIQUE, NE L'EXPOSEZ JAMAIS A L'HUMIDITE OU A LA PLUIE. AUCUNE MAINTENANCE NE DOIT ETRE EFFECTUEE POUR LES PIECES SITUEES DANS L'APPAREIL. LES R E PA R ATIONS ET LA MAINTENANCE DOIVENT ETRE EXECUTEES UNIQUEM ENT PAR UN PERSONNEL QUALIFIE.
NE MODIFIEZ PAS LA PRISE DE CA. CET APPAREIL DOIT ETRE MIS A LA TERRE. DEBRANCHEZ LE CABLE D'ALIMENTATION AVANT DE NETTOYER LE BOITIER DE L'APPAREIL ET AT T E N D E Z QUE L'APPAREIL SOIT COMPLETEMENT SEC AVA N T DE LE REBRANCHER SUR LE SECTEUR.
PER EVITARE DANNI, RISCHI DI INCENDI O SCOSSE ELETTRICHE, NON ESPORRE QUESTA UNIT ALLA PIOGGIA O ALL'UMIDIT. NO N CO NTIENE PA RTI RIPARABILI DALL'UTENTE: FARE ESEGUIRE LA MANUTENZIONE SOLTANTO DA PERSONALE QUALIFICAT O.
NON ALTERARE LA PRESA C.A. Q U E S TA UNIT DEVE ESSERE COLLEGATA A TERRA. DISCONNETTERE IL CAVO DI ALIMENTAZIONE C.A. PRIMA DI PULIRE LA COPERTURA DELL'UNIT; AT T E NDERE CHE L'UNIT SIA COMPLETAMENTE ASCIUTTA PRIMA DI RICOLLEGARLA ALL'ALIMENTA Z I O N E.
SETZEN SIE DIESES GERT NIEMALS REGEN ODER FEUCHTIGKEIT AUS, UM BESCHDIGUNG, BRANDENTWICKLUNG UND ELEKTRISCHE SCHLGEN ZU VERMEIDEN. IM GERT SIND KEINE ZU WARTENDEN TEILE. WARTUNG UND REPERATUREN DRFEN NUR VON QUALIFIZIERTEN TECHNIKERN DURCHGEFHRT WERDEN.
MANIPULIEREN SIE AUF KEINEN FALL DIE NETZANSCHLUSSBUCHSE. DAS GERT MUSS GEERDET SEIN. STECKEN SIE DAS NETZKABEL AUS, BEVOR SIE DAS GEHUSE DES GERTS REINIGEN. SCHLIESSEN SIE DAS GERT ERST WIEDER ANS STROMNETZ AN, WENN ES VOLLSTNDIG GETROCKNET IST.

Fender

Your Fenders Prosonic professional tube amplifiers feature welded, all-steel chassis capable of handling the most extreme conditions. Covered in genuine Tolex for long life and lasting good looks, our cabinets are constructed from premium, hand-selected birch/maple plywood. Only the most roadworthy components are used in the all-tube circuitry. Fender's all-tube reverb adds depth and tone that has kept guitarists smiling for generations. The All-Tube Prosonic is available in 2 models, the two 10-inch speaker combo with Reverb and the Prosonic Head amplifier. Both versions feature a 3-way bias/rectifier switch allowing the player a choice between class A cathode bias,

Pr o soni c

class AB grid bias, as well as the sounds of both tube and solid state rectifiers. The Prosonic is rated at 60 Watts R.M.S. and includes among its many features two gain controls. Gain 1 functions as a standard gain stage whereas Gain 2 functions similar to a compressor, adding sustain while reducing harshness when the volume is increased. Equipped with 2 channels, the Prosonic combo offers the flexibility of accessing each channel and the reverb effect from the front panel or the included two-button footswitch. The Prosonic head also offers the flexibility of accessing each channel from the front panel or the included onebutton footswitch.

Front Pa nel Functions

1. INPUTS - Input for the your guitar or other instrument. 2. INPUT 2 - A lower sensitivity (-3dB) input than INPUT 1. 3. NORMAL/DRIVE - This switch selects between the NORMAL and DRIVE channels. This switch is disabled and when the footswitch is plugged into to the unit. 4. VOLUME - Controls the volume level of the normal channel. 5. GAIN 1 Primary gain adjustment (distortion/sustain) for the DRIVE channel. 6. LED - Indicates operation of the DRIVE channel. 7. GAIN 2 - Secondary gain adjustment for the DRIVE channel. Acts much like a compressor at higher settings.

8. TREBLE - Adjusts the high-frequency level. 9. BASS - Adjusts the low-frequency level. 10. MID - Adjusts the middle-frequency level. 11. MASTER - Adjusts the volume level of the DRIVE channel. 12. REVERB (Combo units only) - Adjusts the reverb effect level on both channels. Switch ON/OFF the reverb effect with the footswitch. 13. PILOT JEWEL - Illuminates when the Prosonic is switched ON and receiving power unless the lamp has failed. (To replace the lamp, unplug the amplifier, unscrew the green jewel and replace the lamp with type T47 bulb.
Prosonic Tube Replacement Tubes must be replaced ONLY with the same type as specified on the tube chart inside the cabinet. To check for tube wear, replace the set in your amp with your spare new tubes as follows: -First replace the OUTPUT tubes in the amplifier and listen for any improvement. - Next, re-insert the original output tubes and replace the PRE-AMP tubes and listen for improvement. -Finally, try replacing BOTH the OUTPUT and PRE-AMP tubes and listen for improvement. - If any combination of tube replacements is a noticeable improvement, reset the amp to that configuration and buy another set of replacement tubes as your spare.
Re a r P a ne l F u ncti ons
1. LINE CORD - Connect the power line cord to a grounded AC receptacle in accordance with the voltage and frequency ratings as listed on the rear panel of the Prosonic amplifier. 2. POWER SWITCH - Turns the AC power on and off. 3. FUSE - Located in the AC supply of the amplifier, the fuse helps protect the unit from electrical fault or tube failure. Replace a failed fuse with the same type and rating. If the amplifier repeatedly blows fuses, take it to an authorized Fender service center. 4. STANDBY SWITCH - Switches the unit between operate and stand-by modes when the power switch is ON. In stand-by mode, no sound will be heard from the amplifier but power is still supplied to the tube filaments keeping them warm and the unit ready to play. Use this switch during short breaks to increase tube life. Wait at least 50 seconds after the power switch is on before putting the unit into the standby mode. 5. RECTIFIER/BIAS SWITCH - Allows for the selection of rectifier sounds and bias classes to best suit your playing style (experiment to find a preferred setting). The (1) TUBE A setting at low volume sounds much like the (2) TUBE AB2 and (3) S.S. solid state AB2 settings at high volume. 6. IMPEDANCE SWITCH (Head only) - Sets the output impedance of the amplifier to match the speaker impedance for maximum power and tube life.

7. SPEAKER (Combo), SPEAKER 1 (Head) - Primary output jack for connection to speakers. A speaker must always be connected at this jack for the unit to be heard. 8. EXTERNAL SPEAKER (Combo), SPEAKER 2 (Head) Output jack for connection to an external speaker. ONLY use in conjunction with the main speaker jack. Using this jack on the Combo automatically switches the amplifier impedance to 8. 9. FOOTSWITCH - Jack for connection to the included footswitch. The footswitch allows remote switching between channels as well as ON/OFF switching of the REVERB effect on the combo unit only. 10.EFFECTS RETURN - Connect cord from external effects devices at this input jack. Inserting a plug at this jack automatically disconnects the units internal connection from the pre-amp to the power amp. 11.EFFECTS SEND - Connect cord to external effects devices at this output jack. This jack can also be used as a line out.

Speci fica t io ns

PART NUMBER* - COMBO: SPEAKER ENCLOSURE: PART NUMBER* - HEAD: POWER REQUIREMENTS: COMPANION SPEAKER ENCLOSURE: POWER OUTPUT: OUTPUTIMPEDANCE: INPUTIMPEDANCE: TUBES: 021-1077-x00 (100V) 021-1007-x00 (120V) 021-1067-x00 (230V) 021-1037-x00 (240V) Aust 2-10 Custom Design Celestion speakers 021-2077-x00 (100V) 021-2067-x00 (230V) 360W. Celestion Vintage 30 speakers: 021-3001-100 (RED) 021-3001-200 (GREEN) 021-3001-000 (BLACK) 021-2007-x00 (120V) 021-2037-x00 (240V) AUSTRALIA/ NZ 021-1047-x00 (230V) UK 021-1087-x00 (230V) Nordic 021-2047-x00 (230V) UK
Class AB2, Solid state rectifier: 60 W R.M.S. (minimum into 8 or 16 ) Class AB2, 5AR4/GZ34 rectifier: 50 W R.M.S. (minimum into 8 or 16 ) Class A, 5AR4/GZ34 rectifier: 30 W R.M.S. (minimum into 8 or 16 ) 8 or 16 (Combo), 4, 8 or 16, (Head). 1 M COMBO Two (2) Five (5) One (1) One (1) HEAD Two (2) Four (4) None (0) One (1) COMBO 5881/6L6WGC 12AX7A 12AT7 5AR4/GZ34 (P/N 099-5090) (P/N 099-5091) (P/N 099-5092) (P/N 099-5097) HEAD
FUSE TYPE: DIMENSIONS: HEIGHT: WIDTH: DEPTH: WEIGHT:
100/120V units: T3 Amp/250V, 18.5 in 24 in 10.5 in 48 lbs. (47 cm) (61 cm) (26.5 cm) (22 kg)
230-240V version T1.6 Amp 250V 9 in. 24 in. 9.5 in. 42 lbs. (23 cm) (61 cm) (24 cm) (19 kg)
*For Prosonic COLOR DESIGNATED part number, replace x with: 1 = RED, 2 = GREEN, 0 = BLACK (Combo Only) Product specifications are subject to change without notice.
A PRODUCT OF: FENDER MUSICAL INSTRUMENTS CORP. CORONA, CA 91720 USA