Setting the Channel and Squelch Code
Select from FRS 114, GMRS 1522 (with GMRS enabled), and 15R22R GMRS repeater channels (with GMRS and Repeater Channels enabled). NOTE: Squelch codes do not cause your conversation to be private. They only allow you to lter out other users on the same channel, so you only hear the radios you want to hear. Squelch Codes are not a scrambling system!
Setting the squelch code to 0 (squelch code off) allows you to hear all activity on the selected channel, but you must be set to the same squelch code as the other person(s) to transmit back. See the Appendix for a table listing all of the 38 Squelch Codes and their frequencies. As you change the main channels, the Rino 130 remembers the last channel/squelch code combination that you were using. For example, you may set the unit channel to 5 and squelch code to 21, then change the main channel to 8 and squelch code to 2. If you change the channel back to 5, the squelch code changes back to its previous setting of 21. See the Appendix for more information on FRS/GMRS and its operational aspects.
Choose from 38 squelch codes. Setting the unit to zero will allow you to hear all transmissions on that channel, but you must be on the same squelch code to radio back. 1. Using the Thumb Stick, highlight the Channel or Code eld and then press the Thumb Stick In to show a list of available channels/squelch codes. 2. Move the Thumb Stick Up or Down to scroll through the selections. Because not all the items t in the window, a slider bar on the right side indicates your current position in the list. 3. Once you have highlighted the desired selection, press the Thumb Stick In.
To change the Channel and/or Squelch Code:
The Scan option allows you to scan through the available channels for voice activity. As the unit scans and receives a signal (or if you transmit), it stops on that channel/squelch code for a few seconds, then continues scanning. When the Rino 130 is scanning and it receives an incoming signal, the Rino 130 automatically decodes the Squelch Code used by the incoming signal. The Rino 130 then uses that Squelch Code when it transmits back to that unit. You may use the Set Scanlist option to pick which channels/squelch codes to scan. Scanning through the all the channels can take time: Selecting only specic channels/squelch codes decreases the scan time and helps prevent the chances of missing a transmission. The Scanlist also has Option Menu choices to Scan Current Codes or Scan All Codes. Choosing Scan Current Codes scans only the Channel and Squelch Code combination in memory.

Scanning and Monitoring

The Monitor option lets you listen to a single channel for any activity, including static and weak voice signals. The Rino series automatically squelches a frequency to lter out unwanted noise. Using the Monitor option temporarily turns off the automatic squelch, allowing you to hear the open channel. If you see a broken transmission symbol (see page 18), there is activity on your selected channel, but the incoming signal does not match the Squelch Code your unit is using. You may choose to monitor a channel if you wish to hear all the activity on a channel.

GPS and FRS/GMRS Radio On; Ready to transmit Position GPS and Weather Radio On (FRS/GMRS Radio Off) GPS and FRS/GMRS Radio On; Ready to transmit Position; Transmitting on FRS GPS and FRS/GMRS Radio On; Position not ready; Transmitting on GMRS GPS and FRS/GMRS Radio On; Position transmitted GPS and FRS/GMRS Radio On; Ready to transmit Position; Receiving transmission GPS and FRS/GMRS Radio On; Ready to transmit Position; Activity on channel. GPS and FRS/GMRS Radio On; Ready to transmit Position; Position received from other Rino user GPS Off; FRS/GMRS Radio On; Position sending not available GPS On; FRS/GMRS Radio Off; GPS operation only
UNIT OPERATION > USING THE RINO 130 RADIO FEATURES
Using the Rino 130 Radio Features
requests from other units more frequently.
1. Enable Send Location (see the Setup Radio section). 2. Press and release either the Talk or Call button. A ag on the top Status Bar or in Marks hand indicates the unit is ready to transmit its position.
Your Rino 130 unit provides many features to enhance your radio experience, such as transmitting your location or any location and receiving contact information. This section reviews some of the advanced radio features. Refer to the Features section for information on all of the features of the Rino 130.
To transmit your location to other Rino users:

Peer-to-Peer Positioning

The Rino 130s most unique feature is being able to send its location to another Rino, which is called Peer-toPeer positioning. With peer-to-peer positioning enabled (see the Setup Radio section) and a GPS position, whenever you press and release either the Call button or the Talk button, the Rino 130 automatically sends out its location. This information is available to all other Rino users that are monitoring the same channel and squelch code. This feature allows you to track the movement of other Rino users and even navigate to their location. Locations may only be sent once every 30 seconds due to FCC restrictions. Your Rino 130 can respond to polling
New Contact Page Overview
The rst time that a signal is received from another Rino user, a New Contact page is displayed. From the New Contact page you can show their location on your Map, Goto their location, or add them to your contact list (select OK). Press Page to ignore this contact.

Map Page Option Menu

Pan MapAllows you to move the Panning Arrow (Map Pointer) about on the map. Refer to the Using the Pan Map Option section for complete instructions. Stop NavigationQuits navigation of a Goto, Route or Track in progress. When you are not navigating to a destination, the Stop Navigation option is grayed out and is non-functional.
Measure DistanceDisplays the distance from one point on the map to another. Restore DefaultsReturns the Map Page to the original factory settings (defaults).

Using the Pan Map Option

The Map Page pan function allows you to display an arrow used to point at and identify items on the map, and to move the map in order to view areas beyond the current viewing area on the display. The map panning function is activated from the Option Menu on the Map Page. Use the Thumb Stick to move the panning arrow (also referred to as the map pointer) in the desired direction. If the arrow moves to the edge of the map display, the map also moves to reveal more area and a busy hourglass appears by the cursor while the data is drawn on the screen. Whenever you place the panning arrow on a map item, the name of that item is highlighted. This feature applies to waypoints, roads, lakes, rivers; nearly everything that is displayed. Press the Thumb Stick In to mark the arrow location or display the map item information page. The Option Menu allows you to: send the location of that item, project a waypoint from it, save it as a waypoint, set a proximity
circle around it, add it to a route, or view the Sun & Moon phase or view Hunt & Fish information from it. On-screen buttons at the bottom of the page allow you to Goto the map item, display it on the map or to select OK and return to the Map Page. Press the Page button to stop panning the map. To nd an item near the map pointer:
1. When using the panning arrow, press and hold the Thumb Stick In to display the Shortcuts Menu. 2. Select Find N Go to display items. Select the category you wish to search (waypoints, contacts, etc.), then select Near Map Pointer from the popup list. The Rino 130 then searches for the items nearest the location of the map pointer instead of your actual location. Map Page with Panning Arrow
Programming the Data Fields

Select Show. Data Fields to view four optional Data Fields on the right side of the screen that can be programmed to provide a variety of travel and navigation information. A list of the choices is shown to the right. Not all data types are available on every page.
1. Use the Thumb Stick to highlight the data eld and then press In to display the list of data options. 2. Highlight the desired option and then press the Thumb Stick In to change the data eld type.
Data Field Options Thee data eld options apply to the Map Page data elds and the Trip Computer data elds. For denitions of these all data elds used in the Rino 130, refer to the Appendix.
Bearing Current Distance Elevation Final ETA Heading Odometer Pointer Sunset Trip Odometer Trip TimeTotal Vertical Speed Course Current ETA Final Destination Final ETE Max Speed Off Course Speed Time of Day Trip TimeMovg. Turn Current Destination Current ETE Final Distance GPS Accuracy Moving Avg. Speed Overall Avg. Speed Sunrise To Course Trip TimeStopped Velocity Made Good

To program a data eld:

Trip Computer Only Location (lat/lon)

Changing Data Fields

Location (selected)

Setting up the Map

The Setup Map option displays the ve Map Setup Pages, each accessed by an on-screen button.
Setup Items Sub-Page Buttons General Setup Lines Setup Points Setup Text Setup Map Data Setup
3. Press Left, then Up or Down on the Thumb Stick to highlight an item on the list. Press Right to return to the sub-page buttons. 5. Use the Thumb Stick to highlight the desired option and then press it In to activate. 6. Press the Page button or the on-screen X button to return to the Map Page.

Options

1. Select Setup Map from the Option Menu and then press the Thumb Stick In to display the Map Setup Page. 2. Press Up or Down on the Thumb Stick to highlight the desired sub-page button, which displays the options list for that sub-page to the left.
To use Map Setup options:
General Setup OrientationTrack Up or North Up; xes the top of the map display to the current track heading or to a north heading. Auto ZoomOn or Off; automatically scales the map to display both your current location and the next point to which you are navigating. DetailMost, More, Normal, Less, or Least; controls how much map detail you see. This setting only applies to a map feature set to Auto. Those features which have a specied scale or are turned Off are unaffected by this setting. Lock on RoadOn or Off; available only if MapSource Data is loaded; when On the triangle icon locks to the road that you are traveling. Display ModeLand or Water.

Tracks Setup Saved Tracks and Track LogScale options; Off, Auto, or 20 ft500 miles, sets the maximum scale at which the feature should appear on the screen. Some types of data display only at certain zoom scales. Goto LineBearing or Course. Track PointsSelect the number of track points per track. Up to 10,000 active Track Points allowed Map Features Setup Points of Interest, Waypoints, Street Label, and Land CoverOff, Auto, or 20 ft500 miles, sets the maximum scale at which that feature should appear on the screen. Some types of data display only at certain zoom scales.
Text Setup Points of Interest, Waypoints, Street Label, and Land CoverNone, Small, Medium, or Large; control the screen size of the name. Map Data Setup ShowCheck box; check mark determines if map data is used or not. Option Menu allows you to choose to show all, show none, or show specic MapSource Data. See also the Appendix.
2. Use the Thumb Stick to move about on the Map Page until you reach the point to which you want to measure. A new Map Pointer eld displays showing the location of the pointer and the direction and distance from where you began the measuring. 3. To begin measuring from a different point, press the Thumb Stick In at the desired location. 4. To stop measuring, press the Page button. Map Pointer Field

Measuring Distance

To use the Measure Distance option:
1. Select Measure Distance from the Option Menu and then press the Thumb Stick In to display the Panning Arrow. Ref displays under the arrow.

Measuring distance

UNIT OPERATION > NAVIGATION PAGE
The Navigation Page provides active guidance with a rotating compass ring that shows your course (track) while you are moving and a bearing pointer to indicate the current direction to your destination (bearing) relative to the course. The Data Field at the top of the page, by default shows you the name of your destination. All ve Data Fields can be programmed to display a variety of navigation data. The list of data eld choices may be found on page 28 and denitions may be found in the Appendix. The Compass Ring functions as a magnetic compass when you are stationary. When you are moving, the heading is controlled by the GPS receiver (based upon settings customized in the Heading Setup Page).
Destination Name (Waypoint) Bearing Pointer Compass Ring
Straight Line Distance to Destination Times to Destination Selectable Data Fields
NOTE: The Compass should be calibrated for the greatest accuracy. Refer to page 36 for information on calibrating the compass.
Using the Navigation Page
The two main components of the Navigation page are the Bearing Pointer and Compass Ring. The Bearing Pointer always points directly to the destination, no matter what your current location might be. The Compass Ring displays your heading.
While you are navigating a route, the pointer indicates the direction (a bent arrow) of the turn to the next point in the route as well as the direction to the current point when you get within 15 seconds Estimated Time of Arrival of the current point. For example, if the arrow is pointing straight up, you are going directly to your destination. If it points any direction other than up, turn and move towards the direction the arrow is pointing until it points up, and then continue in that direction. If you are using the Course Pointer option instead and you drift away from the original line of travel to your destination, the Course Deviation Indicator (CDI) provides graphic indication of drift (right or left) and displays the distance off course. When you are not on an active Goto, Track, or Route (in other words, not traveling to a recorded destination), the window at the top of the page is blank when Destination is selected. The Compass Ring displays your heading

To create a waypoint for a map feature:
1. With the Pan Map feature active, move the panning arrow (map pointer) on the map to the location you want to mark, then press the Thumb Stick. 2. The Mark Waypoint Page displays, automatically assigning a number to the waypoint.
To create a waypoint using the panning arrow:
Saving a map feature as a waypoint
1. Press In and hold the Thumb Stick to access the Shortcuts Menu. Highlight Mark Waypoint and press In. You can also use the Find N Go to view a previous waypoint. 2. Highlight the details eld and press Left or Right on the Thumb Stick to change to the Location eld. Press In and enter the new coordinates using the on-screen numerical keyboard. Highlight and press OK when nished. 3. You may also change the waypoint name and/or symbol or add notes.
To create a waypoint by manually entering its coordinates (lat/lon):

Projecting a Waypoint

Projecting a waypoint from any map item (another waypoint, etc.) allows you to establish a new waypoint on a bearing and distance projected from that map item.
1. Select a map item from the Find N Go Menu. 2. Highlight the Option Menu on-screen button at the top of the Information Page and press the Thumb Stick In to display the options. Highlight Project Waypoint and press In. 3. Highlight either the bearing or distance eld, then press the Thumb Stick In to display the numerical keyboard. Enter the new bearing or distance, then highlight OK and press In to nish.

Editing a Waypoint

A waypoint or contact can be edited to add notes or change the map symbol, name, coordinates, or elevation. You can also delete a waypoint or contact.
1. Use the Find N Go Menu to display the waypoint/ contact or highlight it on the Map Page and press the Thumb Stick In. 2. To make changes to the waypoint map symbol, name, location coordinates, elevation elds and notes, highlight the desired eld and press the Thumb Stick In to display the keyboard. (For Notes, highlight Edit and press In to start entering data, up to 30 characters.) Select OK and press the Thumb Stick In to nish. 3. Highlight the OK button the press the Thumb Stick to save the changes.

To project a waypoint:

To edit a waypoint:
Project Waypoint Page Rino 130 Owners Manual 49
To delete a waypoint or contact:
1. Use the Find N Go feature to display the point. 2. Highlight the Delete button and then press the Thumb Stick In. Conrm the deletion.

You can use the Find Exit option to locate a nearby exit on an interstate highway. Exits are listed only by Nearest. Exit information pages provide a variety of information about services near each exit, such as rest stops, lodging, restaurants, and service stations. Some services such as service stations on this page can be selected and a separate information page displays with specic information concerning what types of fuel, mechanical, and food services are available.
1. Use the Thumb Stick to highlight Exits and then press it In to display the Exit List. 2. Highlight and select an exit type by pressing the Thumb Stick In. 3. A list of exits nearest to you displays. The title box indicates the interstate highway that is served by the exits. Two elds at the bottom of the page indicate distance and bearing to the exit. Scroll through the list to highlight the desired exit.

To nd an exit:

4. Press the Thumb Stick In to display the Information Page for that exit. This page contains the exit description with a list of available services near that exit along with the distance and bearing elds. 5. Use the Thumb Stick to move to the list of services and highlight a selection from the list. 6. Press the Thumb Stick In to display the Information Page for the selected service. The Exit Services Information Page displays the name of the service, its direction from the exit, and a list of the services available, each marked by a check. At the bottom of these Information Pages are onscreen buttons for Goto, Map, and OK. 7. Press the Option Menu button to access additional features. You can select: Send Location (to other Rino users), Project Waypoint, Save as a Waypoint, Set Proximity (alarm), Add to Route, View Sun & Moon (reports for that waypoint), or View Hunt & Fish (reports for that waypoint).
Finding a Point of Interest
You can use the Find Points of Interest option to locate a nearby restaurant, lodging, landmark, public building, park, etc. However, you must have transferred a MapSource MetroGuide map to the unit map database. Otherwise, this option, plus Address and Intersection options, are grayed out and are not functional. Here is a list of Point of Interest categories: Food & Drink Lodging Attractions Entertainment Shopping Services Transportation Emergency & Govt. Manmade Places
In many instances, these categories are subdivided into types, such as in the instance of Food & Drink. When you select Food & Drink from the list of categories, you are then presented with a list of types that includes All Types and cuisine options such as American, Asian, Barbecue, Chinese, and many more.

Food & Drink types

Once you have selected an item, you can display the Information Page for that item. You can then use the onscreen buttons to Goto or view the location on the Map; or use the Option Menu for more choices.

UNIT OPERATION > FIND 'N GO 1. Use the Thumb Stick to highlight Points of Interest and then press it In to display the Points of Interest Categories List. 2. Use the Thumb Stick to select the desired category and then press it In to display the Types List. 3. Use the Thumb Stick to select the desired type and then press it In to display the list for that type. 4. Use the Option Menu at the top of page to select from either By Name or Nearest options. Selecting By Name displays a keyboard allowing you to enter the characters of the name you want. A list of matches displays when enough characters are entered. 5. Use the Thumb Stick to highlight your selection from the list and then press it In to display the Information Page for that item.
To nd a point of interest:
Nearest Food & Drink 6. Use the on-screen buttons to Goto or view on the Map, or use the page Option Menu. 7. Press the Option Menu button to access additional features. You can select: Send Location (to other Rino users), Project Waypoint, Save as a Waypoint, Set Proximity (alarm), Add to Route, View Sun & Moon (reports for that waypoint), or View Hunt & Fish (reports for that waypoint).
Finding an Address or Intersection
You can enter a street number, choose a street name from a list and nd an address within the area of map data coverage or enter two street names and locate the intersection. To use these options, however, you must be using a MapSource product that provides this type of map data.
1. Use the Thumb Stick to highlight Address and press it In to display the Find Address page. 2. Highlight the Number eld and use the keyboard for entering numbers.

To locate an address:

3. Move to the Street eld using the Thumb Stick. 4. Press the Thumb Stick In to display the Select Street Name list. Find the street by using the keyboard to enter characters until a list appears. 5. With the desired street highlighted, press the Thumb Stick In to place the street name on the Find Address page. Repeat this process for city and postal codes, if desired. A window at the bottom of the page displays a list of matches and the quality of each match. You may also use the Option Menu to Clear City, Clear Postal Code or Clear All. 6. Use the on-screen buttons at the bottom of the page to Goto, view the item on the Map, OK to close, or use the Option Menu for other choices.

Entering an Address

To locate an intersection:

Map DatumOffers a selection of nearly all map datums in common use. Every map is based on a map datum (a reference model of the earths shape) and is usually listed in the title block of the map. If you are comparing GPS coordinates to a paper map, chart, or other reference, the map datum in this eld must match the horizontal map datum used to generate the map or other reference. The default datum is WGS-84 (World Geodetic Survey 1984) and should only be changed when using maps or charts specifying a different datum. If a map does specify a datum, use the options list to nd datums applicable to the region of the map, selecting the one that provides the best positioning at a known point. If necessary, you also may choose the User datum for custom designed grids.
NOTE: The User datum is based on a WGS-84-Local datum and is an advanced feature for unlisted or custom datums. To learn more, check your local library or the Internet for educational materials on datums and coordinate systems.
Distance/SpeedChoose from three units of measure to display your rate of travel. Elevation/Vertical SpeedChoose from two units of measure to record your elevation and vertical speed. PressureChoose from millibars or Inches to measure the pressure.

Display Setup Page

You can adjust the amount of time that the backlighting feature stays on and adjust the screen contrast. Backlighting TimeoutChoose from Stays On or delays of 15 seconds, 30 seconds, one minute, or two minutes before timing out.
Contrast AdjustmentCan be adjusted from light to dark using the slider adjacent to the contrast bar. To access the Display Setup page:
1. Press the Page button or the Menu icon to open the Main Menu. 2. In the Main Menu, scroll down and select Setup. 3. Select the Display icon to open the Display Setup page.

To adjust the contrast:

1. Highlight the contrast slider and then press the Thumb Stick In. 2. Move the Thumb Stick up or down to move the slider to set the contrast.

Heading Setup Page

You can select the type of heading displays, the types of North References, or enter the magnetic variation.
1. Press the Page button or the Menu icon to open the Main Menu. 2. In the Main Menu, scroll down and select Setup. 3. Select the Heading icon to open the Heading Setup page.
To access the Heading Setup page:
1. Highlight the Backlight Timeout eld and then press the Thumb Stick In. 2. Highlight the desired option and then press the Thumb Stick In.
To set the backlighting timeout:
Heading Setup Page Rino 130 Owners Manual
DisplayAllows you to choose from Cardinal Letters, Degrees or Mils. North ReferenceYou can choose from True, Magnetic, Grid or User options. If User is chosen, you must correct for the Magnetic Variation. The Electronic or GPS compass uses the North Reference setting to create a bearing. Switch to Compass Heading when BelowEnter the desired speed for the Rino 130 to switch from using GPS to using the compass for guidance. For more thanEnter a time limit to switch to the compass. When you travel at the speed entered above for the time entered here, the Rino 130 switches from GPS to the compass.
1. Highlight the eld and then press the Thumb Stick In to display the options. 2. Highlight the option and press the Thumb Stick In to activate.

Interface Setup Page

The Interface Settings Page allows you to choose from different input/output serial data formats. This feature is used when connecting to external NMEA devices, a DGPS beacon receiver, a personal computer, etc. See the Appendix for using the Rino 130 with MapSource.
1. Press the Page button or the Menu icon to open the Main Menu. 2. In the Main Menu, scroll down and select Setup. 3. Select the Interface icon to open the Interface Setup page.
To access the Interface Setup page:

To select either option:

The available interface formats are: GarminThe proprietary format used to exchange waypoint, track, and map data with a PC. Use this setting for transferring data when using a MapSource product. Garmin DGPSAllows DGPS input using a Garmin beacon receiver and a standard RTCM SC-104 and DGPS tuning. NMEA In/NMEA OutSupports the output of standard NMEA 0183 version 3.0 data. Use this for real-time plotting with MapSource or 3rd party programs. Text OutAllows ASCII text output of location and velocity information without input capabilities. RTCM INAllows DGPS input using a standard RTCM SC-104 format without output capabilities. RTCM In/NMEA OutAllows DGPS input using a standard RTCM SC-104 format and supports the output of standard NMEA 0183 version 3.0 data. RTCM In/Text OutAllows DGPS input using a

Waypoint Bomber

HINT: Mark stationary objects such as trees and poles, and drop a bomb when an opposing player is near that object! Adjust the rules to your liking!
To re at the cursor location, press the Thumb Stick In. To re at your current location, press the Talk button. Press Call to view the scoreboard at any time. Press Page to quit the game at any time.
Rino 130 Owners Manual 97

Clothesline

Team members select the same user symbol and then attempt to hit or clothesline other players by pressing the Talk button when an opposing team member is between them. You may also mark a point and assign it a symbol to be used as a stationary team member. Wait 30 seconds between attempts. Press Call to view the score and Page to quit the game. Think of this as a high-tech game of tag. Team members select the same user symbol and then attempt to assimilate others into their team by getting within 30 feet of them and pressing the Talk button. Press Call to show the score and Page to quit the game. You can set a time limit so the largest team wins, or play until the other team is completely assimilated. Set your own rules and enjoy!

Assimilation

pits while navigating a maze of platforms. You can be transported by slides that curve or move diagonally. When you think you know where the beast is press the Thumb Stick In to initiate aiming when you are in an adjacent spot. With the Thumb Stick, point the arrow in the direction where you think the beast is and press the Thumb Stick In to re. When you lose a game, the layout of hazards, slides, warning platforms, and the location of the beast is shown. A scoreboard keeps track of your wins and losses. Press Page anytime during the game for further instructions, to turn the sound On/Off, or to quit.

Beast Hunt

The objective is to nd and kill the beast with an arrow before it incinerates you or you fall into one of several
APPENDIX > WHAT IS FRS?

What is FRS?

FRS, or Family Radio Service, is a UHF radio frequency band allocated by the FCC for general public use. The operating frequency ranges from 462.5625 to 467.7125 MHz, with a maximum transmitting power of one half watt. FRS radios are small and lightweight, making them ideally suited for outdoor activities. FRS radios typically feature a half watt of transmit power. You can expect your FRS radio to offer reliable operation at a one-mile range. If the area between you and another FRS operator is free of obstructions, operation up to two miles can be achieved. FRS radios broadcast on one of 14 channels, each with a specic frequency within the FRS band. The use of FRS radios does not require a license. FRS was intended for use by families and small groups as an inexpensive means of two-way voice communication. FRS is intended for use throughout the United States, its territories and possessions. It may also be used in Canada. FRS is not approved outside of these areas and

Maximum ElevationThe highest elevation reached. (Altimeter Page Only.) Maximum SpeedThe maximum speed the unit has moved. Minimum ElevationThe lowest elevation reached. (Altimeter Page Only.) Moving Avg. SpeedAverage speed of the unit while moving. OdometerA running tally of distance travelled, based upon the distance between second-by-second position readings. Off CourseThe distance left or right you are from the original course (path of travel). Overall Avg. SpeedYour average speed. PointerIndicates the direction to the next destination. SpeedDisplay rate of travel in miles per hour, kilometers per hour, or nautical miles per hour. SunriseThe time at which the sun rises on this day. SunsetThe time at which the sun sets on this day. Time of DayThe time for the selected time zone. To CourseThe compass direction you must go in order to get back to the original course.
Rino 130 Owners Manual 111
Trip OdometerA running tally of distance travelled since last reset. Trip TimeMovingA running tally of movement time elapsed since last reset. Trip TimeStoppedA running tally of stopped time elapsed since last reset. Trip TimeTotalA running tally of all time since last reset. Total AscentThe total distance ascended. (Altimeter Page Only.) Total DescentThe total distance descended. (Altimeter Page Only.) TurnThe angle difference (in degrees) between the bearing to your destination and your current line of travel. L means turn Left. R means turn Right. Velocity Made GoodThe speed at which you are closing on a destination along a desired course. Vertical SpeedYour rate of altitude gain/loss over time.
APPENDIX > INTERFACE INFORMATION

Interface Information

Interface formats are selected in the Setup Interface Page. See also the MapSource Setup section of this Appendix for information on using the Rino 130 with MapSource. The input/output lines on your Rino 130 unit are RS-232 compatible, allowing easy interface to a wide range of external devices, including PCs, differential beacon receivers, marine autopilots, and /or a second GPS receiver. The NMEA 0183 version 3.0 interface format is supported by the Rino 130 and enables the unit to drive up to three NMEA devices. NMEA 0183 Version 3.0 Approved Sentences: GPGGA, GPGLL, GPGSA, GPGSV, GPRMB, GPRMC, GPRTE, GPVTG, GPWPL, GPBOD GARMIN Proprietary Sentences: PGRME (estimated error), PGRMM (datum string), PGRMZ (altitude), PSLIB (beacon receiver control)
DGPS (Differential GPS) corrections are accepted in RTCM-SC-104 version 2.0 format through the Data IN line. The Garmin GBR 21 and GBR 23 are the recommended beacon receivers for use with the Rino 130. Other beacon receivers with the correct RTCM format may be used, but may not correctly display status or allow tuning control from the GPS unit. The Rino 130 may be hard-wired to a serial connector using a Data Only Cable. Refer to the wiring diagram and the Rino 130 unit data connection illustrated below. The PC Interface Cable provided with this unit allows you to connect your Rino 130 to a PC-compatible computers serial port.

Turn your radio OFF in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy. VehiclesRF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles. Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle. Posted FacilitiesTurn your radio OFF in any facility where posted notices so require. Commercial AircraftMany commercial airlines prohibit the use of FRS radios on board. Switch OFF your radio before boarding an aircraft or check the airline rules. Blasting AreasTo avoid interfering with blasting operations, turn your radio OFF when in a blasting area or in areas posted: Turn off two-way radio. Obey all signs and instructions. Potentially Explosive AtmospheresTurn your radio OFF and do not remove your battery when you are in any area with a potentially explosive atmosphere. Obey all signs and instructions. Sparks from your battery in such areas could cause an explosion or re resulting in bodily injury or even death.
120 Rino 130 Owners Manual
Areas with a potentially explosive atmosphere are often, but not always clearly marked. They include fueling areas such as gasoline stations, below deck on boats, fuel or chemical transfer or storage facilities; vehicles using liqueed petroleum gas (such as propane or butane); areas where the air contains chemicals or particles, such as grain, dust, or metal powders; and any other area where you would normally be advised to turn off your vehicle engine.
Accessories 103 Accuracy 101 Acquisition time 101 Address 59 Add to Route 52, 53, 55, 56, 58 Alarm 75, 90 Alarm Clock 90 Altimeter Page 37 Altitude 37 Arriving at Destination 64 Arrow 27 Ascent 37, 110 Auto Zoom 30
64 BlueChart 104 Bread Crumb Trail 72 Broken Signals 18 Buttons Locked 46
Barometric Pressure 38, 39 Basemap 1 Battery icon 6 Battery Life 102 Battery Type, Changing 87 Bearing 32 Bearing Pointer 32, 34, Rino 130 Owners Manual
Calendar 88 Calibrate Altimeter 41 Compass 34, 36 Call 99 Call Tone 16 CDI 33 Channel 10 City 55 Compass 87 Calibrate 35 Contact 20, 54 Course Deviation Indicator 33 Course Pointer 33, 34 CTCSS 10, 108 Current location 47
Data Fields 28, 34, 40, 41, 71 Denitions 110 For Route Page 71 Data Transfer 105 Defaults 4, 26, 34, 38, 42, 67, 87 Delete Waypoint 50 Descent 37, 110 DGPS 112 Display Mode 30
License 100 Finding Address 59 By name 51, 52 City 55 Contact 54 Exit 56 Intersection 59, 60 Point of Interest 57 Find N Go 50, 51, 64, 66 FRS 1, 7, 10, 99, 108
Editing Routes 66 Waypoints 49 Electronic Compass 36 Elevation 37, 38, 39 Changes 37, 39 Plot 39 Exit 56

How to use Garmin Rino 130
Created by: John Cruz, Vladimir Ivanov, UH-Hilo EPSCoR-ITER Last updated: 2/14/2007
//./sdal/how-to/ht_garmin_rino130.doc
Installing Batteries Note: The Rino 130 operates on three AA alkaline batteries located in the back of the unit. 1. Remove the battery cover on the back of the unit. Turn the D-ring turn counterclockwise. 2. Insert batteries observing the polarity reference molded into the unit housing. The negative (-) battery terminal always orients closest to the spring. 3. Reinstall the battery cover by inserting the bottom hinge clip and closing the cover. Turn the D-ring turn clockwise. Initializing the Rino 130 1. Take the Rino 130 outside where it has an unobstructed view of the sky and turn it on. 2. The unit begins to search for satellite signals. Tracking Satellites is displayed while the units is initializing. 3. Initialization should take no more than five minutes. When the GPS is initialized and ready for navigation, the message 3D accuracy is displayed on the radio page. Setup Menu: Before start using the GPS Device it is a good idea to confirm that the GPS setup format matches your data format. 1. In order to do that you need to go to the main menu - click once on the THUMB STICK and then choose Main Menu 2. Scroll down and select Setup. 3. Using the THUMB STICK (left, right, up, down) navigate trough the different properties. Make sure to check the Time, Units and System. If you need to change some of the properties, navigate to it with the THUMB STICK key and change by clicking the THUMB STICK key. The Device will give you all the options that you can choose from. Scroll trough them using the THUMB STICK key.
Calibrating the Compass The electronic compass in the Rino 130 must be calibrated (outdoors away from metal objects) whenever new batteries are installed and before you use the unit for navigation. Note: The Rino 130 must be held face up and level during compass calibration and use. The more the unit is tilted on either axis, the less accurate the compass reading will be.
1. Press the PAGE button unit the navigation page is displayed. 2. Use the THUMB STICK to highlight the option menu on-screen button and then press the THUMB STICK IN to display the menu. 3. Highlight the Calibrate Compass option and then press the THUMBSTICK IN to display the calibration page. 4. The information screen explains how to calibrate the compass: To calibrate compass: Slowly turn two full circles in the same direction while holding the rino equipment. 5. Press the THUMBSTICK IN to activate the start button. The screen prompts you to Turn slowly. Keep the unit level and begin to rotate the Rino 130 in your hand. A Just Right message displays when you are turning at the proper rate. If you turn it too slowly or to rapidly, a Too Slow or Too fast message appears. 6. When the Calibration Successful message appears, use the THUMBSTICK to highlight the OK button. If a Calibration Failed message appears, press the THUMBSTICK IN to restart the calibration.
Navigating with your Rino 130: Marking a waypoint is simply capturing your current location and storing it in the units memory. The unit must be turned on and the tracking satellites to mark a waypoint.

To mark a waypoint:

1. Press the THUMBSTICK IN and hold it until the shortcuts menu is displayed. 2. Highlight Mark waypoint and press the THUMBSTICK In to display the mark Waypoint page. 3. Highlight the Name field and press the THUMBSTICK IN. Enter a new name by using the THUMSTICK to select letters from the keyboard (see above). When finished, highlight OK. Then press the THUMBSTICK IN.

4. Highlight the Symbol field and press the THUMBSTICK IN. Choose a symbol then press the THUMBSTICK IN to accept the selection. 5. Highlight the OK button at the bottom of the page and press the THUMBSTICK IN to save the waypoint. Create a Waypoint: 1. Press the THUMBSTICK IN and hold it until the shortcuts menu is displayed. 2. Highlight Mark waypoint and press the THUMBSTICK In to display the mark Waypoint page. 3. Highlight the Name field and press the THUMBSTICK IN. Enter a new name by using the THUMSTICK to select letters from the keyboard (see above). When finished, highlight OK. Then press the THUMBSTICK IN. 4. Navigate to the Location menu on the screen and change the coordinates using the THUMBSTICK to the coordinates of your waypoint. 5. Use the THUMBSTICK to change from the Location menu to the other menus Direction, Elevation, Note and Timestamp. Use the THUMBSTICK to change the information in these menus. 6. Highlight the OK button at the bottom of the page and press the THUMBSTICK IN to save the waypoint. Navigate to a Waypoint: 1. Click on the THUMSTICK and select Main Menu. 2. Navigate to the Find N Go option using the THUMBSTICK. 3. Select Waypoints and choose to sort them by distance (nearest) or by name. 4. Select the waypoint you wish to go to and click on it. 5. After that choose the Go To button in the bottom left corner of the screen. To create a breadcrumb trail: 1. Use the PAGE button to display the map page. 2. The default zoom is 80 miles. Press the ZOOM button in to view the breadcrumb trail you will make in the next step. 3. Walk away from your original location for at least three minutes. As you are walking, notice that a breadcrumb trail of your path is left on the map. To create a track: 1. Go to Main Menu by clicking twice on the THUMSTICK. 2. Navigate to the Tracks button and click it. 3. Turn on the Track log by clicking ON in the right corner of the display. The Device will start recording the track. 4. To Save your track click on the Save button. The device will give you opportunity to choose what part of the Entire Log to save in your track as well as to name your new track.
5. To Delete your track go back to the Track Log page and select one of the already saved tracks. After that you can edit or delete that track. To delete it click the Delete button in the lower left corner of the display. 6. To navigate to a track instead of clicking on the Delete button, select the one that is below it TracBack. The device will ask you to navigate to the End or to the Begging of that track. Simply choose the one that you wish.
Setting up the radio To select a channel: 1. Highlight the Channel field and press the THUMBSTICK IN. 2. Using the THUMBSTICK, select one of the 14 available channels. Press the THUMBSTICK IN to accept the selection. To select a squelch code: 1. Select the Code field and press the THUMBSTICK IN. 2. Using the THUMBSTICK, select one of the 38 available codes. Press the THUMBSTICK IN to accept the selection.

Using the Weather Radio The weather radio provides a constant update of the weather conditions, with is helpful white outdoors or planning for a road trip. When the Weather radio is on a tower emitting signals is shown in the information picture on the radio page. The FRS/GMRS radio cannot be used when the weather radio is on. There are 7 weather radio channels available. To turn the Weather Radio on and off: 1. Open the Radio page by pressing the PAGE button or using the on-screen Main Page Menu button. 2. Use the THUMB STICK to highlight the Option menu on-screen button and then press the THUMBSTICK IN to display the menu. 3. When Use Weather Radio is highlighted, press the THUMBSTICK IN to turn on the weather radio. You can select Enable Weather Radio after the Weather Radio is on. 4. To turn the Weather Radio off, press the THUMBSTICK IN when Use FRS/GMRS Radio is highlighted. This will switch the Rino 130 back over the FRS/GMRS radio.
Transmitting with the RINO 130: The Rino 130 can transmit to and receive messages from other FRS radio users on the same channel and squelch code. To transmit on your Rino 130: 1. Press and hold the TALK button, and in a normal voice, speak into the microphone area on the front of the Rino 130 from a distance of about 3-4 inches. 2. When you are finish talking, release the TALK button. Your location is updated on all receiving Rinos. 3. If you want to call another user or update your location on another Rino, press and release the CALL button. This sounds a call tone on all Rinos that are monitoring your channel and squelch code. Your positon is updated when your signal is received by the other unit. To turn off the device press and hold the Power button.