Reviews & Opinions
Independent and trusted. Read before buy Hafler DH-220!

Hafler DH-220

Manual

Preview of first few manual pages (at low quality). Check before download. Click to enlarge.
Manual - 1 page  Manual - 2 page  Manual - 3 page 

Download (English)
Hafler DH-220, size: 4.8 MB
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Hafler DH-220About Hafler DH-220
Here you can find all about Hafler DH-220 like review and other informations. For example: .

Hafler DH-220 manual (user guide) is ready to download for free.

On the bottom of page users can write a review. If you own a Hafler DH-220 please write about it to help other people.

 

[ Report abuse or wrong photo | Share your Hafler DH-220 photo ]

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

Comments to date: 8. Page 1 of 1. Average Rating:
bnj 2:46pm on Monday, October 25th, 2010 
my own is now and Currently, Hewlett Packard launch the author of SATA DVD with the additional techonology which developed only, Lightscribe.
taxihamster 5:51pm on Thursday, October 14th, 2010 
Caution: this is not an ATAPI/IDE drive! This drive has a SATA interface, but this is not clearly stated in the description. A pleasure to use Since purchasing this product, I have been burning many CDs and DVDs without issue.
doctorlove 8:05am on Thursday, October 14th, 2010 
Value for Money. Bought for a Sony Vaio Netbook. Did not install software that came with it. Just plugged in and worked straight away. Easy to use. Quality product The product arrived and is a nice slim shiny little unit. Very light weight. Just plugged it in.
rofro 2:59pm on Saturday, September 11th, 2010 
LG, SONY. Worth possessing it..... Compatible writer with fast reading and writing features from the reputed company.
xyl145988 5:22am on Friday, August 13th, 2010 
I have four of these burners. burn dvds great speed none that I have found yet I hve had it for 3 months Fast, Quiet, Great Value! Great Value for the Price Poor Instructions GOT IT AT BEST BUY BEFORE XMAS, TRYING TO FIND ANOTHER. AT THIS POINT THE BEST DVD BURNER I HAVE EVER HAD FROM ANY MANUFACTURER, OR DESIGN.
irnis 3:15am on Monday, June 28th, 2010 
Samsung External DVD Writer I was disappointed with the quality of this DVD Writer and although it was cheap in price did not come up to expectation.
q1w2e3r4 10:10am on Tuesday, May 25th, 2010 
I have this drive installed with a SuperMicro P8SCT motherboard and found it to be incompatible used with Windows XP.
andreas.oelkers 1:14am on Wednesday, March 31st, 2010 
This unit seems to do all that is is supposed to do. Because it is SATA I did have a problem getting it to work in my PC. Easy installation, quick burning performance, quiet Slightly more expensive.

Comments posted on www.ps2netdrivers.net are solely the views and opinions of the people posting them and do not necessarily reflect the views or opinions of us.

 

Documents

doc0

POWER AMPLIFIER

INSTRUCTIONS for OPERATION and KIT ASSEMBLY
CAUTION: IF THE SPEAKER FUSES BLOW, SOME DISTORTED SOUND CAN BE HEARD. THEREFORE IF AMPLIFIER MALFUNCTIONS, ALWAYS CHECK FOR BLOWN FUSES FIRST.
THE DAVID HAFLER COMPANY 5910 Crescent Boulevard, Pennsauken, New Jersey 08109
Hafler DH-200 Power Amplifier

serial

number in all communications

INTRODUCTION

The Hafler DH-220 is a two channel audio power amplifier designed to the very highest performance standards. It is available either as a kit, or fully assembled. Its 115 watt per channel power rating is sufficient for driving all loudspeakers in home applications, and its design assures extremely low distortion of all types. A combination of high performance, dependability, reliability, and moderate price is in the Hafler tradition of using the very latest technology to provide outstanding value. The DH-220 circuit is a refinement of the DH-200 design, a Hafler landmark which has achieved worldwide recognition, and has elicited glowing reviews since its 1979 introduction. As in the DH-110 preamplifier, particular attention has been paid to component quality, using polypropylene or film capacitors wherever feasible, for example, for superior sound. Combining the latest power MOSFET technology with uniquely simple and effective circuit topology reduces distortion of all types, and at all power levels, over the full audio frequency spectrum, to the vanishing point. In addition to its pace-setting performance achievements, the conservative mode of operation accomplishes a new high in long term reliability and exceptional resistance to abusive operating conditions. This is one of the direct benefits of MOSFET utilization in overcoming a serious limitation of conventional transistors - their tendency to self-destruct under other than normal operating conditions. So rugged is the DH-220 that it can deliver more than ten amperes into a short circuit! The speed - measured as the slew rate - of this design delivers unmatched transient linearity, revealing the most delicate shadings, textures and nuances of the music, surpassing the capabilities of the most revealing loudspeakers and cartridges by a wide margin. Coupled with its unconditional stability, and ability to deliver adequate power into any loudspeaker load, the result is absolute freedom from listening fatigue. The longer you listen to this phenomenal amplifier, the more certain you will be that you could not have made a better choice. The oversized power transformer and bridge rectifier; the massive heat sinks; the conservative operating levels of the MOSFET output devices - all are evidence of the design efforts to achieve exceptional reliability simultaneously with state of the art sonics and specifications. And this circuit is convertible to a high power monophonic amplifier with comparable stability and specifications. The fully complementary, symmetrical push-pull circuit, which is direct coupled throughout (except at the input), incorporates all silicon devices in a format which is directly related to the highly acclaimed DH-110 preamplifier. Its unique selfDH-110 protecting output stage prevents the thermal runaway which is a common threat to solid state amplifiers. The ruggedness and conservative operation of the output stage allows the DH-220 to avoid the need for special protective circuits which could compromise audio performance. Basic protective systems provide maximum security against malfunction damage to the amplifier or the speaker: the AC line fuse, B + fuses, thermal breakers, and loudspeaker fuses. Nothing hinders the essential purity of the audio signal. Those who use these instructions to assemble the DH-220 kit will find that the left and right audio modules (printed circuit and heat sink assemblies) are preassembled and pretested. This greatly simplifies the kit assembly so that it can be done in only a few hours without special skills or know-how. Because of the modular arrangement, it is possible to operate on one channel if the other requires service, and avoids the need to return the entire amplifier in cases where only one channel is at fault. Accessories for special applications include provision for monophonic use; a panel for standard 19 rack mounting; and an alternative power transformer for international AC line voltages. Through advanced engineering geared to the audio perfectionist, and an efficient no-frills approach, Hafler is making high technology high fidelity affordable.

CONTENTS

Operation. Page 3 Assembly Instructions. 4 Wiring the Kit.. 6 If Problems Arise. 10 Service and Warranty. 11 AC Line Connections for Overseas Use. 12 Kit Parts List.. 13 Schematic Diagram. Component Value Listing. 15 Pictorial Diagram. Insert
Copyright 1984, All rights reserved.

INSTALLATION

The DH-220 is most likely to be installed out of sight in most applications, since its power may be controlled by the AC switching of most audio preamplifiers, like the Hafler DH-110. If your control unit does not provide switching capacity sufficient for the amplifier 7 amp needs (plus other equipment it is also s switching), you should use the amplifier own power switch. In s that case, turn on the preamplifier first; then turn the amplifier on a few seconds after the preamp has been turned on, to avoid any unnecessary turn-on transients from some preamplifiers. Likewise, switch the power amplifier off first. If the amplifier is to be installed close to a record player, you should first check its position for freedom from hum pickup by the cartridge from the field radiated by the power transformer of the DH-220. Although the design of the transformer minimizes such radiation, certain cartridges are more sensitive than others, and require separation from the amplifier. Check at a comparatively high volume setting, and while swinging the tone arm throughout its arc. Often a few inches additional spacing will eliminate the problem. Be sure to provide sufficient ventilation for the amplifier. Unobstructed air circulation around the finned heat sinks and above the amplifier is important for long, trouble-free life. Never put anything on top of the cover perforations. It is normal for the top and the heat sinks to become warm in use. It is expected that the amplifier will always be resting on its feet, which should be on a hard enough surface that air flow underneath is not obstructed. If it is mounted in a rack, or through a panel, the feet may be removed so long as adequate ventilation is provided through the bottom openings.

OPERATION

The red pilot lamp which is integral with the power switch glows whenever the amplifier is turned on. A blown AC line fuse is the most likely cause if it is not illuminated when the amplifier is switched on. The pilot lamp also provides a high temperature indication. In the unlikely event that the amplifier ceases to function, and the amp blinks on and off steadily, it indicates that one of the thermal breakers has shut down the amplifier because of excessive temperature rise in a heat sink. When the heat has dissipated in a few minutes, the amplifier should return to normal operation. If the lamp again blinks, check for insufficient ventilation, or an excessive input signal, or an input which may have dangerous signal content (such as oscillation). Failing evidence of this, the amplifier may have malfunctioned. Because of the very large heat sinks, it is highly unlikely that any normal signal will cause the amplifier to overheat.

Loudspeaker Fuse Selection Loudspeaker Power Ratings
There are no U.S. standards for rating the power handling of loudspeakers. As a result, the manufacturers usual music power ratings, or suggested amplifier limits, are of only minimal help in determining safe operating levels with amplifiers which can deliver substantial amounts of power. You must take into consideration the type of music, and the levels you like, to provide long term trouble-free operation of your speaker choice, when you have a sizeable amplifier like the DH-220.

Connections AC

The DH-220 power amplifier is supplied with 2 amp fuses in the speaker lines. Experience has shown that since an overload must exist for a few seconds for a fuse to blow, a 2 amp fuse will protect most speaker systems, and only blow when overload occurs. Smaller fuses tend to blow too easily, and larger fuses do not adequately protect most speaker systems. A pair of 5 amp fuses are also supplied as alternatives for the speaker fuse holders. These should be substituted if the power output of the amplifier is to be tested, and these or intermediate values may be used if the amplifier is to be operated at very high power levels into 4 ohm loads. If the manufacturer of your speakers recommends a specific value of fuse for their protection, we suggest that you obtain A C fuses of that value and install them in the back panel.
The AC power cord should be plugged into 120 volts, 60 Hz, on the switched outlet of a preamplifier which can provide at least 7 amps, or 840 watts. Then the amplifier power switch may be left on, and it will be controlled by the rest of the system. Or. it may be plugged into a 120 volt wall outlet, and switched on and off independently. If your line (mains) voltage is different, be sure you have the alternate power transformer which can accommodate several line voltages, and be sure it is wired for your mains voltage as described later in this manual before you pIug in the amplifier.
Conventional shielded cables, such as those supplied with your preamplifier, provide the input signal to the sockets on the back panel of the DH-220. Be sure that the outer shield connection is secure, to avoid hum. The length of these cables (so as to permit remote location of the amplifier, if desired) is limited only by the output impedance of the preamplifier. If it is 600 ohms or less, as with the DH-101 and DH-110 Hafler preamps, for inDH-101 stance, cable lengths up to 50 feet are premissible without loss of
performance. Special low capacitance cables enable even greater distance between preamp and amplifier. It is desirable to keep the left and right input cables close together throughout their length to minimize the likelihood of hum pickup. Also, you should avoid running them parallel to AC cords - these should be crossed at right angles. Output The loudspeakers (or headphones) connect to the red and black terminals on the back panel. These binding posts provide several convenient alternative connecting methods. The screw cap may clamp the bared wire end, or a spade lug attached to it, but a better connection will be made by locating the hole drilled through the shaft of the terminal when the cap is unscrewed. Insert the twisted end of the bared wire so that the cap will clamp it in place. Always be sure that no strands of wire are unsecured, and that the bared end is not too long to risk contacting other elements. A soldered end or fitting is the safest solution. These terminals also accept standard plug-in banana pin connectors, including the double ones with standard 3/4 spacing, available from electronic supply houses. These are the most convenient, especially if you may wish to interchange speakers occasionally. It is important to maintain correct phasing of the speakers when making their connections. Some speaker terminals are coded red and black, or + and -, etc. It is important that the sense of one speaker connections match the others. If one is s reversed, you will find that the sonic image has a hole in the middle, and that it is deficient in bass. Speaker wire always identifies one conductor to make this easy. There may be a molded ridge in one lead, or the color of the insulation on one wire is different, or the wire itself may be color coded. If pin

A soldering gun is not recommended. The unfamiliar user is more likely to damage the etched circuit boards with its higher heat potential and unbalanced weight. Also, because he may not wait long enough for it to reach operating temperature each time it is switched on, poor solder connections are more likely. Pencil irons are much lighter and easier to use, and there is no waiting time when solder connections follow in sequence, as in kit building. Make sure you have a holder for it, though, and always unplug it when you take a break.
few seconds to allow a good bond. When cool, check the connection by wiggling the wire. If in doubt, or if the connection is not shiny, re-heat the joint. Excess solder may be removed from a connection by heating it and allowing the solder to flow onto the iron, which is then wiped on the sponge. ALL SOLDER USED MUST BE ROSIN CORE. Never use acid core solder or any separate flux in electronic work. Silver solder is also not suitable. If in doubt about unmarked solder, always obtain a fresh supply of rosin core solder. We recommend 60/40 for easiest use. Do not confuse it with 40/60, which is harder to melt. The general procedure is to use a hot iron for a short time to heat a connection, then add solder with the iron still in contact. Remove the solder once it flows, and then remove the iron. A cooler iron applied for a longer time is more likely to damage components, or lift the copper circuit pattern from the boards. A break in the etched circuit can be mended by simply soldering a small piece of wire across it. Do not allow much build-up of solder on the tip of the iron, or it may fall into adjacent circuitry. When soldering to a numbered hole on the board, insert the wire from the components side, and apply the iron, leaving some bare wire exposed so that you can see that the hole is then filled with solder for a secure bond. A round wooden toothpick is suggested so that you can heat and clear the hole of solder if it hinders your inserting the wire. Some builders prefer to clear every hole first with a touch of the iron and toothpick. If the wire has first been tinned, no additional solder may be necessary if solder fills the hole, but it is good practice to push the wire through, and then back it up a bit, to be sure solder fills the hole from both sides. Make certain a bright, shiny flow is evident from the wire, across the hole, onto the circuit pattern on the board. Tinning refers to the process of applying a light coating of solder to the bared wire end. This keeps all the strands secured, and also makes a good connection easier. Simply touch the wire with the iron for a couple of seconds, and apply solder. Allow the excess to flow away onto the iron. When properly done, the wire is uniformly bright, and no larger than before. The hookup wire supplied with this kit does not normally need tinning, for it is pre-tinned.

find it easier to first start them with a regular screwdriver, to set the thread, and then use the more convenient nut driver, if one is available.

Mechanical Assembly

1 r When you unpack your kit, you will find that the transformer, large capacitors, and the output assemblies have been temporarily fastened to the chassis for safe shipment. Disengage these, and include this hardware with the rest when you check off the components against the parts list in the back of the manual. We recommend this check-off to be sure you have everything, and to enable you to identify any unfamiliar items by comparing them with the pictorial diagram. An egg carton is ideal for keeping hardware items separated. A set of hardware includes one screw and one KEP nut (with its attached lockwasher). Always install the lockwasher side of the nut first. If the size of the hardware is not specified, use the #6 size. The smallest size is #4 and #lO the largest. Always insert the screw from the outside of the chassis. It will simplify matters if you first separate the #4 nuts from the #6 nuts, which have the same outside dimensions. A #4 screw will pass through a #6 nut, aiding identification. 2 L Select the four rubber feet, four sets of # 6 hardware, and the chassis. Insert each screw through a foot so that the head is recessed, and install the feet on the outside at each corner hole. Select th e two red output terminals. Install them in the sequence shown below, in the two center holes LR and RR marked ' +at the rear of the chassis. Before you fully tighten the first nut, unscrew the cap to expose the hole drilled through the threaded shaft. Connection of loudspeaker wires will be easier if these holes are positioned vertically. A nail through the hole will keep it positioned while the hardware is tightened. Each connecting lug should point downward before the last nut is secured. Be sure both nuts on each terminal are tight, as they are difficult to reach when the amplifier is completed.
4 Select the two black output terminals and install them or either side of the red ones, at LB and RR. Be sure the shaft holes are vertical, the lugs point downward. and each nut is tight.
5 n Select the two round fuse holders, and two each 1/2 rubber washers, lockwashers and nuts. First install the rubber washer on the holder, so it will be outside the chassis, and then fasten the fuse holders at LF and RF, with the tip lugs pointing towards each other, toward the center of the chassis. 6 U Select the two input sockets and 4 sets of #4 hardware. Install the sockets inside the chassis at LS and RS so that the short lug of each socket is near the hole between the two sockets. Select the single ground lug (with lockwasher teeth) and one set of #4 hardware. Install it between the input sockets, pointing toward the bottom. Bend it out for access, and twist it 90 for easier insertion of a wire later. Be sure this lug is tight, as the locking teeth must cut through the chassis paint for a good ground connection. 8 ri Select the four-lug diode block DB, the long # 6 screw, and a nut. Install the rectifier in the center hole near the rear of the chassis, with the plus (+) terminal located over the tiny indexing hole at position four. Correct orientation of this rectifier is essential for proper wiring. 9 n Select the single fuse clip, and one set of #4 hardware. Install the clip in the right front chassis hole FC, closest to the foot. Select the two dual fuse clips and four sets of #4 hardware. Install these in the pairs of holes FL and FR on either side of the center of the chassis. Select the 5-lug terminal strip and two sets of #4 hardware. Install it in the front holes TS, next to the single fuse clip. Note the position of the mounting lugs (to the right) in the pictorial diagram.

NOTE: Kits provided with the multiple voltage power transformer for use in locations outside the United States having a line (mains) voltage other than 120 VAC are also supplied with an additional twolug terminal strip which is to be installed using an additional set of #4 hardware on the other side of the chassis, below the dual fuse clip FL.
Connect the shorter lead to FC lug #l. (S). Connect the longer lead to the lower hole of TS lug #2. (S). Note that lug 2 is the second protruding lug on the terminal strip. It is not the mounting bracket for the terminal strip. Soldering this lead to the lower hole now will make later connections to the top portion of the lug easier. Be sure no stray strands of either line cord conductor are left unsoldered. 14 Prepare a 6 1/2" green wire. Connect one end to dual fuse clip FL lug #l. Connect the other end to the other dual clip FR lug #l. (S). Prepare a 6 1/2" white wire, Connect one end to FR lug #3. Connect the other end to FL lug #3. (S). Prepare two 7 white wires. Start with one wire projecting 3/4" beyond the other, and twist them uniformly together throughout their length. Connect the projecting end to RF lug #l. (S). Connect the corresponding end of the other wire to RFlug #2. (S). Place this pair over the right edge of the chassis.
170 Prepare two more 7 white wires. Start as before with one wire 3/4" longer, and twist them together. Connect the longer end to LF lug #2 (S). Connect the other wire to LF lug #l. (S). Place these wires off to the left. Prepare an 8 green wire and a 10 white wire. Start with the white wire 3/4 longer than the green wire, and twist them uniformly together. Connect one end of the green wire to the lug on black output terminal LB. Connect the corresponding end of the white wire to red terminal LR. (S). Place these wires off to the left.
Select the power switch. Install it with the red window to your right as viewed from the front. The switch snaps into chassis hole PS from the outside. 13 q Select the AC line cord and the plastic strain relief. Separate the two conductors for 2. Cut 1 off one of the two leads, and strip 1/4" of insulation from each lead. Twist the strands tightly, and tin each end. Make a sharp 'V' in the cord 8 1/2" from the longest cut end by bending it back on itself. Install the relief with the small end nearest the cut end of the cord. Crimp the two halves of the relief around the wire at the 'V' with heavy pliers, to partially form it before insertion into back panel hole AC. Then grip the larger diameter with the plier tips, squeeze it tightly, and insert the cord and the relief from the outside. A flat side of the relief mates with the hole shape, and it snaps into position when fully inserted.
19 c3 Prepare a 7 green wire. Connect one end to terminal LB. (S-2). Place this wire towards the center of the chassis. 20 Ll Prepare a 10 white wire and a 10 green wire. Starting with the white wire 3/4" longer, twist them together. Connect the projecting white wire to red terminal RR. (S). Connect the green wire to terminal RB. Place these wires off to the right. C Prepare a 51/2" green wire. Connect one end to terminal RB. (S-2). Place this wire towards the center of the chassis. Prepare a 16 green wire, but strip 1 1/4" of insulation from one end. Prepare a 15 white wire. Start with the normally stripped (l/4) ends even, and twist these wires uniformly together. Thread the longer bared end of the green wire through LS short lug #2 from the top left, then through GLlug #3, and connect it to RSshort lug #4. Solder only LS lug #2. Connect the corresponding end of the white wire to LS lug #l. (S). Place this wire up under the chassis rear lip, above the output terminals, and off to the left. 23 L! Prepare a 6 1/2" green wire. Connect one end to CL lug #3. (S2). Place this wire over the rear of the chassis. 24 C Prepare a 10 green wire and a 10 white wire. Twist these together with the ends even. Connect the green wire from the right to RS short lug #4. (S-2). Connect the white wire to RS lug #5. (S). Place these wires off to the right. Prepare two 22 white wires, and twist them together throughout their length. 8 in from one end of the pair, cut one of the wires, and unwind it about 11/2" in each direction from the cut. Strip 1/4" of insulation from each of these cut ends. Place the longer portion of the wire along the lower front edge of the chassis, with the break at the terminal strip TS. Connect the cut end from the left to TS lug #2. Connect the other end to the lower hole of TS lug #5. (S). Place this pair along the front edge of the chassis, under the power switch, with the ends projecting from the front corners of the chassis. 26 il Select a 1 megohm resistor (brown-black-green) and trim the leads to 1/2. Connect one lead to TS lug #2. (S3). One of these 3 leads has already been soldered to the lower lug hole. Connect the other lead to TS lug #3. 27 n Select the diode and trim its leads to 1/2. Note that one end of the diode is marked with a stripe (or an arrow head will point to that end). Connect the marked end to TS lug #4. Connect the other lead to TS lug #3. (S2). Prepare a 4 green wire. Connect one end to TS lug #4. Select a spade connecting lug, and solder it to the other end. Place this wire down against the chassis, and connect it to the PS lug on the right, near the edge of the chassis. The proper way to attach a spade lug to a wire is to first cut the bared wire end to the right length (no more than 1/4" so that the insulation will be securely gripped by the longer, outer tabs, while the wire does not protrude into the spade clamp area. Tin the bare wire end. Bend the 8 29

The transformer leads may be trimmed as desired for a neat job, but be sure you do not cut any of them too short (particularly if yours is the multi-voltage version, and any change to a different supply voltage is likely). Cutting the leads too short for re-use may void its warranty, if it is thought to be defective. Consult the multi-voltage diagrams elsewhere in this manual fcr connections to the terminal strips which may differ from the stepbystep instructions here. Be sure all strands of each transformer lead are tinned and soldered together before connection to a lug, so that there is no possibility of a stray strand touching anything but the lug. Select the remaining spade lug, and solder it to the black transformer lead. Connect it to the PS left lug. u Select the.005 (502M) disc capacitor, and trim its leads to l/2 or less. Wrap one lead around the shaft of the spade lug which is connected to the PS left (inside) lug. Wrap the other lead around the shaft of the spade lug connected to the middle lug. Solder both leads. Be sure there is adequate clearance between these connections, and that the spade lugs are fully engaged. 41 Connect the black/white transformer lead to TS lug #5. (S3). One of these wires was previously soldered to the lower hole of this lug.
these. If it is filled with solder, running the iron along the underside will uncover the hole, and it may be cleared with a wooden toothpick. Now position the right module (with the breaker at the front when the long bottom row of eyelets is next to the chassis) with the circuit board up, against the side of the chassis. Wires will be connected to the holes from the top of the board, and you must be sure they are soldered securely to the bright circuit pads Each hole is . plated through - it makes a connection to the other side of the board - and a good solder connection which heats the wire and the circuit pad properly will allow solder to flow through the hole for a secure connection. Even though the connecting wires are just long enough to make the connections now, they will be rather long when the amplifier is completed. That is why working room is limited. Any wire which is to be connected to a hole on the board should have a tight, tinned end. The wire supplied in the kit is already tinned, so it would not normally require additional tinning unless the tip is frayed. Melt a small amount of solder on the tip of the iron so that it will make a good contact with both the bared wire end, and the circuit pad as the wire is inserted into the hole. Then add additional solder so that there is a smooth, bright transition from the wire to the board as it cools undisturbed. If you must use a great deal of heat on a connection, make sure that you have not loosened any adjacent connections in the process - especially wires from the back side of the board. The holes #lo and #3 are very close to capacitors on the board. Be sure heat does not damage these capacitors.

42 G Twist together the two red transformer leads for neatness, and connect one iead to DB lug #2. Connect the other to DB lug #3. ci Select the.Ol mfd (103M) disc capacitor, and trim its leads to 3/4" Strip two 1/2 pieces of insulation from the green wire, and slide one piece over each of the capacitor leads. Connect one lead to DB lug #2. (S-2) Connect the other lead to DB lug #3. (S-2) Make sure both leads are securely soldered to each lug. Here you could overlook a poor connection. Connect the red/yellow transformer lead to the center of the bare wire between the capacitor lugs. (S). Lowest hum in the unit will be attained when all of the wires which connect here are as close to the center of this wire as possible. Connect the single green wire from output terminal LB to the center of the bare wire next to the transformer lead. (S). 0 Connect the single green wire from RB to the center of the bare wire on the other side of the transformer lead. (S). 47 q Connect the green wire from CL lug #3 between the two input sockets to the center of the bare wire also. (S). 0 Select the output assembly modules (the two major items in the kit). You will note that the only difference, which identifies the left or the right module, is the position of the thermal breaker, which is located between one pair of output transistors on the heat sink rib. Before connecting wires to these modules it is best that you take the time to inspect the underside of the bottom row of holes to make certain that connections already made to some of these are well soldered. You will be making connections from the top side to holes 3,5,6,7,8 and 10. Make sure the proper connection point is clear at each of
49 II Prepare a 51/2" green wire. Connect one end to hole #lO on the circuit board. (S). Make sure it cannot contact the transistor mounting screw near the underside. Connect the other end to FR lug # 2 (S). Prepare a 6 white wire. Connect one end to hole #3. (S). Connect the other end to FR lug #4. (s). 51 C Select the green and white twisted pair from the output terminals RR and RB. Connect the white wire to hole #5. (S). Connect the green wire to hole # 7 (S). 52 q Select the pair of white wires from RF. Connect the shorter wire to hole #6. (S). Connect the other wire to hole #8 (S). Select 4 of the long sheet metal screws. Take care to see that no wires are trapped in the process, while you tilt up the module and fasten it to the end of the chassis. The screws are inserted between the heat sink fins, and then engage the chassis.
Select the green and white pair of wires from input socket RS. Connect the white wire from the left to the top (rear) hole #l. (S). Connect the green wire to hole #2. (S). These wires should be soldered to the circuitry on the underside of the board, although they are connected from the top side of the board, assuring a good connection. These wires will be specifically positioned later, though they now seem long.

62 ! Select the green and white pair from input socket LS. Connect the green wire to the top rear hole #2. (S). Connect the white wire to hole #l. (S). Solder these on the back of the board. 63 I ! Tuck the excess of the remaining white pair of wires into the front corner, and connect one wire to each lug of the thermal breaker. Solder each. 64 : : Select the 7 ampere slo-bid fuse (a slo-bid fuse has distinctive internal construction) and install it in the single fuse clip FC. 65 C Select four 5 amp regular fuses, and install them in the dual fuse clips FL and FR. Select the two 2 amp fuses, and install them in the twist type fuse holders on the back panel. These fuses will provide reasonable protection for most speakers. See the Operation section of this manual for more detailed information. The remaining 5 amp fuses are alternates for the back panel holders for high power test purposes. For lowest distortion performance and lowest noise, correct placement of some wires is important. The wires from the output terminals and the back panel fuse holders should be kept against the chassis. The input socket pairs should be about an inch above the chassis, (the left pair can be tucked under the rear chassis lip), and should turn upwards at the bottom center of the circuit board, about 1/2" to 1 off the board, in the plane defined by the edges of the finned heat sinks. The wires to the dual fuse clips should be kept away from the board and against the chassis, bringing the excess length forward of the fuses. The leads to the power supply capacitors should be kept away from the boards. The 10
Adjustments for Bias and DC Offset
These two potentiometers on each circuit board have been set at the factory and should not normally require adjustment for the life of the amplifier. In the event of repairs such as transistor replacement, the following is the procedure, after removing all input and output connections to the amplifier.
Bias Remove the B + fuse F2. This fuse is in the line from the + c a p a c i t o r terminal to hole #3 on the board. Connect an ammeter ' + ' !ead to the fuse clip nearest the large filter s capacitors. Connect the - lead to the other side of the fuse clip. Avoid intermittent connections, and do not short the leads together. Turn the amplifier on, and if possible adjust the line voltage to 120 volts. Adjust P2, near the middle of the board, to 275 mA. Turn the amplifier off, and when the current drops to zero, then remove the ammeter and replace the fuse. Offset A DC voltmeter capable of resolving 10 mV variations is needed. Connect it to the output terminals of the selected channel, and adjust Pl, near the top of the board, to zero volts, + 10 mV. A small correction of the control will produce a large initial change, which will settle down in a second. Repeat these small changes to achieve zero volts.

VOLTAGE CHART measured with 120 volt line, no signal. with respect to the ground buss between the two capacitors in the power supply. E 62.6 -62.6 B 62.1) -62.0 c 0.88 -0.37 61.8 61.8 -62.0 -62.0 E 63.0 -1.27 -63.0 -63.0 1.0 -0.8 B 62.0 -0.6 -62.0 -62.0 1.54 -1.35 c 1.54 1.-1.35 65.0 -65.0 s G 1.0 1.0 -0.8 -0.8 D 65.4 65.4 -65.4 -65.4

-0.32 0.8 0.8

0.22 0.22 0.22

Q4 Q5 Q6

QlO Q11

Ql2 Q13

Q401 Q402 Q403 Q404
KIT PARTS LIST KIT PARTS LIST
Minor variations may sometimes be encountered in value or appearance. These will not affect performance.
Fuse Envelope 6 Fuse, 5 ampere 2 Fuse, 2 ampere 1 Fuse, 7 ampere, Slo-Blo 1 Additional fuse, 4 ampere, Slo-Blo (International use only) Hardware Envelope 1 Lug, solder type, internal tooth, #Lug, solder type, #lO 3 Lug, spade, l/Nut, #4-40 KEP 11 Nut, #6-32 KEP 4 Nut, #l0-32 KEP 2 Nut, l/2, for fuse holder 12 Screw, machine, #4 x 5/ Screw, machine, #6 x l/Screw, machine, #l0 x l/Screw, #l0 x l/4, SEMS 16 Screw, sheet metal, #6 x l/Screw, machine, #6 x 3/Washer, flat, 7/Washer, locking, internal tooth, l/2 for fuse holder 2 Washer, rubber, l/2, for fuse holder Small Parts Envelope 1 Capacitor,.0l mfd, disc (103M) 1 Capacitor,.005 mfd, disc (502M) 1 Capacitor,.39 mfd 1 Diode 1 Label, serial number 1 Resistor, 1 megohm
Part No. SF012 SFSFSF026 Part No. HZHZxzo14 HKlll HK112 HK113 HK118 HAHAHAHAHPHAHW114 HW116 HRll7 Part No. CZ112 CZ113 CEl l7 QD115 LR015 RDl13
Part No. 1 Chassis MS149 Cover MS152 CL121 Capacitor. 10,000 mfd, 75V Bracket, round, for capacitor HZ125 Diode rectifier block QDll1 Feet, rubber HR149 Fuse holder, round XA013 Fuse clip, single XA012 Fuse clip, dual XA014 Input socket XPO14 Line cord, with plug WA016 Output module assembly (1 each, left & right) AH326 Output terminal, black, with hardware XKOll Output terminal, red, with hardware XK012 Power switch SLlll Strain relief, plastic HR144 Terminal strip, 5 lug XK018 Additional 2 lug terminal strip (International use only) XK016 Power transformer TA123 Alternate transformer (International use only) TA124 Wire, white, #18 WS024 wso22 Wire, green, #18 LM016 Registration card

- - o , * +d2-D3+t -Rg-

-R4_R 2-C2__cs-
VIEWED FROM COMPONENT SIDE
COMPONENT VALUES COMPONENT VALUES
All resistors are l/4 w carbon film unless specified otherwise

TB40 I Thermal Breaker TB402 Thermal Breaker Ll Output Inductor

SPECIFICATIONS

Power Rating: Less than 0.02% total harmonic distortion at Input Impedance: 47,OOO ohms. Input Sensitivity: 1.55 volts rms for watts into 8 ohms. Damping Factor: 300 to 1 kHz into 8 ohms z
any power level up to 115 watts continuous average power per channel into 8 ohms at any frequency between 20 Hz and 20 kHz with both channels driven.
IM Distortion ( S M P T E:) Less than O.OOS%, from 1 watt to 1 15

watts into 8 ohms.

Typical THD at 115 watts into 8 ohms:
60 to 10 kHz into 8 ohms z
Rise Time: 10 kHz. 60 volts peak to peak square wave, %
I kHz - 0 0025% __ IO kHz - 0. 7 % 20 kHz - 0.012/
Frequency Response into 8 ohms:

to % 2.5 us.

Slew Rate: 10 kHz. 60 volts peak to peak square wave: 30 VI,~ s. Semiconductor Complement: 26 transistors. 8 power Mosfets, 29 diodes, 4 zener diodes. 1 diode bridge.
- 3 dB. 2 Hz to 160 kHz at 1 watt +O, -0.5 dB, 6 Hz to 60 kHz at watts
Typical Channel Separation: 20 Hz:> 75 dB
Power Consumption: watts into 8 ohms: 840 VA;
1 kHz:>85 dB 20 kHz: >6S dB
Signal to Noise Ratio, unweighted: Better than 100 dB at 115
Quiescent: 125 VA. Size: 5-1/8 high. 16 wide, 10-l/2 deep.

Net Weight: 26 Ibs.

Shipping Weight: 30 Ibs.
All Specifications are subject to change without notice.

Printed in USA

INSTRUCTIONS FOR THE HAFLER DH-222 AMPLIFIER BRIDGING KIT DH-222 FOR THE DH-220
The DH-222 may be installed in a Hafler DH-220 power amplifier to enable easy conversion to a high power monophonic amplifier, bridging the two conventional channels to a single floating output which can deliver in excess of 400 watts into an 8 ohm load. Its rated power output is 350 watts across the audio band. When switched to monophonic operation (UP), signal input should be provided to the LEFT input jack only, and the output should be connected only to the two center BED ( +) terminals. No connection of the load is to be made to the black output terminals. Because of the floating output, neither side of the load may be grounded. Thus it is unlikely that stereo speaker switching boxes, or headphone adapters may be used, as these often have a common ground between the left and right channels. The speaker fuses may be replaced with higher values than the 2-5 ampere range suggested for stereo operation, if desired, depending on the degree of protection for the speaker which is intended. The graph shows the nominal sustained power output limit of a 7 ampere standard fuse, which is the maximum recommended value. Smaller values will provide more protection for the speakers; larger ratings are at the user risk. s Both speaker fuses should be the same value. If one speaker fuse blows in mono operation, both should be replaced, for it is likely that the second has been weakened. For equivalent load impedance, each speaker fuse provides the same power output protection as in stereo operation. With the internal conversion switch DOWN, the amplifier functions as a conventional stereo amplifier, with normal input and output connections. The minimum recommended load impedance, which is limited only by thermal factors (ability of the heat sinks to dissipate high energy levels), is 6 ohms in mono; the usual 3 ohms in stereo. The amplifier circuit can safely accommodate lower impedance loads, of course. The conversion, which takes less than an hour, involves only changes to the input wiring, and installation of the switch with its mounting bracket and one resistor. These instructions assume familiarity with the usual kit building descriptions, and reminders. For more details in this regard, see the construction section of your DH-220 amplifier manual. You must be certain you have made a good solder connection wherever one is called for, not only to the wire you have attached, but to any others already connected to that point. The notation ( S) indicates a soldered connection; (S-2) denotes that there are two wires to be soldered. Use only 60/40 rosin core solder. Be careful not to let the soldering iron touch adjacent components on the circuit board: excessive heat could change their operation, with the possibility of damage to the amplifier.

12 cl Select the red and black pair from the right channel circuit
board holes 1 and 2. Connect the black wire to switch lug #3. (S-2). Connect the red wire to lug #2. (S). 13 Cl Select the green and black pair and separate the wires for about 1%. Connect the green wire to right circuit board hole A. (S). Connect the black wire to hole E. (S). Hole A is located in line with the switch about 11/2 from the rear edge of the board. E is located 1/2 below hole 2, near the top of the board. I4 Cl Place the green and black pair towards the rear of the module, and down past the midline of the switch. Where it passes lug #5, approximately 41/2"from the end of the wires, cut only the green wire. Strip each end 1/4" Connect the short green section to switch lug #4. (S-2): Connect the longer green wire from the left board to switch lug #6. (S). Be careful no wires are pinched as you reinstall the right modI5 ule to the chassis with 4 screws. Place the long green and black pair under the rear lip of the chassis. The pairs to the top eyelets on each board, and to the connections in the center of the board should be kept at least 1/2" off the board, where they are clear of the components. Make sure the unconnected black wire end near the left circuit board cannot touch any components. The switch lever should be placed in the upper position for 16 monophonic operation. In the lower switch position, the amplifier functions as a conventional stereo amplifier. Reinstall the amplifier cover with the remaining 8 screws.

 

Tags

TD-8841T WD440 5RM-75 F12684FDS DP-2060 4500DN Detector DW7 60 KX-TCD715 AC205 HT-X20R SD-254 LA32A330j1N Finepix F700 TE 610 KF-50E200A 711MP EB-GD93 Kxtga641EX M7720 AJ-D200P Atas-120A Office X4 CI-5100T WR125R Remote Futaba 14MZ SC-DX103 ZFC321WBB DTH6300F JY-HD10 UE-37C6500UW KDC-W7037 Solo 2100 Tv410 HC600MLS WFR 2460 MAG-500 WX-C50 7118F Odelia 450 LFD750 1120E LE-32S71B DI183F Dvdr7310H 58 Sbcru410 Set-TOP Melnor 3060 D1776 Ixus I5 UX-BS60 LBP5300 Intermatic ST01 Foreman GV5 HF-33W Voice DUO DCC-450 DSC-H2 E2000 Juno D Meter VF Dvdr3300H-05 Wayteq X820 IC-M71 DSC-G1 D52W15 Minor 11 LAV-72760 KX-T7636 Pocket PC XC-IS21T Recorder PCS-1 Live 6 NN-5050 PRG50 Moulinette T71 SB916SK HM400JI N1050V HR2304 DVD-P361K Diversion RUE-4202 ZWF3105 DMP450N TD4200 DS-10 Series Handytone-286 Writer Floxir MDX-F5800 LN32B450c4 CW-29Z408PQ K2500 RM-VL700U 32LC56 CC-222MK2

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101