iP41 IB (without remote control) size: 178 x 178 color: Black Mar. 27, 2009
Limited 1 Year Warranty Information
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of one year from the date of original purchase. Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased. Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period, SDI Technologies will repair or, at its discretion, replace this product without charge (except for a $10.00 charge for handling, packing, return UPS/postage, and insurance). This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center listed below. The product must include proof of purchase, including date of purchase. The fee for service without proof of purchase is $25.00. Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective batteries are the most common cause of problems encountered. If service is still required: 1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box. 2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty period. 3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $10.00 ($25.00 without proof of purchase). 4. Send the unit prepaid and insured, to the Factory Service Center listed below. Consumer Repair Department SDI Technologies Inc. 1330 Goodyear Drive El Paso, TX 79936-6420 Disclaimer of Warranty NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by unauthorized persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CDs or tape cassettes (if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner. This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original purchaser. In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders, members or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary or punitive damages. (Some states do not allow limitations on implied warranties or exclusion of consequential damages, so these restrictions may not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Your acknowledgment and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies product. 2009 SDI Technologies, Inc. All rights reserved

Model iP41 Alarm Clock for iPhone / iPod
Questions? Visit www.ihomeaudio.com For any other questions: 1-800-288-2792 Toll Free
Questions? Visit www.ihomeaudio.com
iP41-040309-0 Printed in China

Table of Contents

Quick Start...... 1 Controls and Indicators / iP41 Display.... 2 Getting Started...... 3 Using the iP41..... 4-6 Using the Optional Remote Control.... 7 Install/Replace the Remote Control Battery.... 7 A Consumer Guide to Product Safety.... 8 Troubleshooting..... 9
iPhone/iPod does not respond to the unit iPhone/iPod does not dock properly Symptom Unit no respond (no power) Possible Problem

Troubleshooting

Solution Plug the AC adaptor into a wall outlet and plug the connector into the supply jack on the unit AC adaptor isnt plugged to a wall outlet or the connector is not plugged into the power supply jack o the back of the unit Wall outlet is not functioning Using wrong insert/ no insert dock or iPhone/iPod has obstruction
Plug another device into a wall outlet (same outlet) to confirm the outlet is working Make sure the dock insert is the proper fit to your iPhone/iPod Remove your iPhone/iPod from the dock and check for obstruction on the connectors in the dock and on your iPhone/iPod. Then reseat it in the dock. Remove your iPhone/iPod from the dock and check for obstruction on the connectors in the dock and on your iPhone/iPod. Then reseat it in the dock. Upgrade software on your iPhone/iPod via iTunes. Please make sure your iPhone/iPod is working properly before docking with the unit. Please refer to your iPod manual for details. Remove your iPhone/iPod from the dock and check for obstruction on the connectors in the dock and on your iPod. Then reseat it in the dock. iP41 doesnt support 3rd generation iPod Please make sure your iPhone/iPod is working properly before docking with the unit. Please refer to your iPod manual or apple.com/support for details. Decrease the volume. Turn off EXB bass effect If iPod original sound source is poor quality, distortion and noise are easily noticed with high-power speakers. Try a difference audio source such as a music CD. If you are using an iPod Shuffle or external sound source like older generation iPod, try reducing the output volume on the device itself. Also, try turning bass boost OFF.

iPhone/iPod is not docked properly

Maintenance

Place the unit on a level surface away from sources of direct sunlight or excessive heat. Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should be placed between it and the furniture. Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzine, thinner or similar materials can damage the surface of the unit.
Your iPhone/iPod software is too old iPhone/iPod is locked up iPhone/iPod is not docked properly
iPhone/iPod didnt charge up

FCC Information

This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Using 3rd generation iPod iPhone/iPod is locked up/frozen iPhone/iPod battery has problem Sound is distorted Volume level is set too high Sound source is distorted
This equipment complies with the limits for a Class B digital device as specified in Part 15 of FCC Rules. These limits provide reasonable protection against radio and TV interference in a residential area. However, your equipment might cause TV or radio interference even when it is operating properly. To eliminate interference you can try one or more of the following corrective measures: Reorient or relocate the receiving antenna. Increase the distance between the equipment and the radio or TV. Use outlets on different electrical circuits for the equipment and the radio or TV. Consult your dealer or an experienced radio/television technician if the problem still exists.
Modifying or tampering with your systems internal components can cause a malfunction and might invalidate the systems warranty and void your FCC authorization to operate it. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada.

Remote Control didnt work
Remote control battery is weak/dead Remote Control is too far way from main unit
Replace remote battery with new CR2032 battery Use the Remote Control closer to main unit

April 03, 2009

A Consumer Guide to Product Safety

iP41 Quick start

1: AC power 2: inserts & cradles

RESET TEST ESET R

Attach AC adaptor cable to jack on back of the iP41 and plug the other end into a wall socket to play and charge iPhone/iPod
Use this insert For this iPhone/iPod
4: watching horizontal screen video
Gently pivot unit to the left until it lies flat. The clock display will adjust to the new orientation. Select your video and press the Play Button on the iP41 to play your video.
When used in the directed manner, this unit has been designed and manufactured to assure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use. Keep these instructions handy for future reference. Take special note, and adhere to all warnings on the unit and in the instruction and service manual. 1. Water and Moisture - The unit should not be used near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. 2. Ventilation - The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, it should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or placed in a built-in installation, such as bookcase or cabinet that may impede the flow of air through the ventilation openings. 3. Heat - The unit should be situated away from heat source such as radiators, heat register, stoves, or other appliances (including amplifiers) that produce heat. 4. Power Sources - The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. 5. Power Cord Protection - Power supply cord should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. It is always best to have a clear area from where the cord exits the unit to where it is plugged into an AC outlet. 6. Cleaning - The unit should be cleaned only as recommended by the manufacturer. 7. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. 8. Attachments - Do not use attachments not recommended by the product manufacturer. 9. Lightning and Power Surge Protection - Unplug the unit from the wall outlet and disconnect the antenna or cable system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage to the product due to lightning and power-line surges. 10. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 11. Damage Requiring Service - The appliance should be serviced by qualified service personnel when: A. The power-supply cord or plug has been damaged. B. Objects have fallen into or liquid has been spilled into the enclosure. C. The unit has been exposed to rain. D. The unit has been dropped or the enclosure damaged. E. The unit exhibits a marked change in performance or does not operate normally. 12. Periods of Nonuse - If the unit is to be left unused for an extended period of time, such as a month or longer, the power cord should be unplugged and take out batteries from the unit to prevent damage or corrosion. 13. Servicing - The user should not attempt to service the unit beyond that described in the users operating instructions. All other servicing should be referred to qualified service personnel.

3: iPhone/iPod

Select the dock insert for your iPhone/iPod model from the table below and place insert in dock. Never dock an iPhone/iPod without the proper insert in place. Insert the short cradle for your iPhone or iPod touch or tall cradle for nano 4G into the slot next to the dock

iPod touch 2G insert 16

Insert iPhone/iPod into dock (iPhone/iPod must not be in a skin or case). iPhone/iPod will charge while docked. Press the Play Button on the iP41 to play your iPhone/iPod.

iPod nano 4G insert 17

iPhone 3G Insert 15 iPhone 3G

iPod Touch 2G

iPod nano 4G
NOTE: If you do not have an insert for your iPhone/iPod, please visit www.ihomeaudio.com or call iHome toll free at 800-288-2792 to purchase one.

Controls and Indicators

Hour Button Alarm Button Minute Button Alarm Reset/Power Button
Using The Optional Remote Control Unit
Power Button turns unit ON and OFF Volume Buttons raise and lower volume on the unit. Pressing FWD/REV while iPhone/iPod is inserted will FWD/REV to next/previous track Pressing and holding FWD/REV while iPhone/iPod is docked will scan forward/reverse within currently playing track. Pressing Play/Pause from power off mode will play iPhone/iPod. Pressing Play/Pause while iPhone/iPod is docked and playing will pause iPhone/iPod. Press again to resume play.
iPhone/iPod cradle in slot
Snooze/Dimmer Button Play/Pause Button Volume- Button Sleep Button Volume+ Button DST Switch Clock Adjust Button Expanded Bass Effect Switch Aux-in Jack
Remote not included with all iP41 models. To order a remote, please visit www.ihomeaudio.com
Pressing the mute button will mute the unit. While unit is muted the volume display will flash. Pressing mute again or volume up or down will unmute. The up, down, fwd, rev, menu and enter buttons are used for iPhone/iPod menu navigation The shuffle and repeat buttons will activate/deactivate the iPhone/iPods shuffle and repeat modes The snooze button works exactly same as on main unit.

DC Jack

Install/Replace the Remote Control Battery
Install/Replace the Remote Control Battery (for models with remote control) To order a remote control, visit www.ihomeaudio.com The remote control battery is already installed at the factory. When the remote control stops operating or its range seems reduced, replace the battery with a new one. 1. The battery door is located on the back end of the unit. 2. Slide the battery door to release the battery door latch and remove the battery door. 3. Insert a CR2032 3-volt lithium battery. Make sure the polarity (the + and side of the battery) is correct. Battery Compartment 4. Replace the battery compartment door back in the remote control. NOTE: PLEASE DISCARD BATTERIES PROPERLY

Display in Movie Mode (product is sideways)

Back Panel

iP41 Display
Time Display Alarm Indicator Sleep Indicator Battery Low Indicator DST Indicator PM Indicator iPod/iPhone Indicator
Display in iPhone/iPod Mode (product is upright) 2

Using the iP41

Using Sleep Mode
Press the Sleep Button while your iPhone/iPod is playing to enter sleep mode and continue to press to step through the available sleep times: 90, 60, 30 and 15 (OFF will cancel sleep mode). A sleep icon will appear on the display. The iP41 will play for the number of minutes set, growing gradually softer until shutting off the unit and the iPhone/iPod at the set time. Press or Button to set sleep volume. Note that sleep volume is separate from normal/alarm volume setting.

Getting Started

Thank you for purchasing the iHome iP41 Alarm Clock for your iPhone/iPod. Designed specifically to work with your iPhone or iPod Touch, this system provides high quality audio performance and lets you enjoy videos in horizontal view. Please read this instruction carefully before the appliance is operated and keep it for future reference. Install iPhone/iPod Insert & Cradle Your iP41 comes with two cradles for support when viewing videos in horizontal mode and three inserts to ensure your iPhone/iPod fits properly in the dock. To place a cradle: 1. Select the small iPhone /iPod touch cradle for use with those models or the taller nano cradle for use with nano 4G. 2. Press cradle into the vertical cradle slot on the unit (near the dock). To place an insert: 1. Select the insert for your iPhone/iPod. (see table on page 1) 2. Gently press the iPhone/iPod insert into the dock. 3. Carefully place your iPhone/iPod into the dock. The iPhone/iPod must not be in a case or skin. Install AC Adaptor Connect the AC adaptor cable plug into the jack on the back of the system, then plug the AC adaptor into the wall outlet. Install/Replace backup Battery The iP41 uses a CR2032 battery for backup battery system to provide continuous alarm operation and clock settings in the event of a power failure. If the Backup Battery has been installed and a power failure occurs or the AC cord is accidentally disconnected, the display backlight will not remain lit, but current time and alarm time settings will be temporarily maintained. Otherwise, you must reset the time and alarm settings. 1. Please make sure the AC adaptor is connected. Otherwise all settings may be lost during battery replacement. 2. Open backup battery compartment door located on the back of the unit. 3. Insert a new CR2032 battery, checking that the polarity (+ and ends of the battery) matches the drawing near the battery compartment. Close the compartment door. WARNING: Lithium batteries can explode or cause burns if disassembled, shorted, recharged, exposed to water, fire, or high temperatures. Do not place loose batteries in a pocket, purse, or other container containing metal objects, mix with used or other battery types, or store with hazardous or combustible materials. Store in cool, dry, ventilated area. Follow applicable laws and regulations for transport and disposal.

Using Dimmer

Press the Snooze/Dimmer Button during normal operation to adjust the brightness of the LCD display to high, medium, low or off.

Using the EXB effect

Slide the EXB Switch at the back of the unit to the ON position to enable the EXB sound enhancement circuitry, designed to provide bigger bass sound. Slide to OFF to cancel the effect.

Setting Clock

1. Set the DST Switch located on the back of the unit to +1 to add one hour or to -1 to subtract an hour. When set to +1 the DST icon will appear. 2. Press and hold the Clock Adj Button located on the back of the unit until the display flashes. Press the Hour and/or Minute Button to set the time. Hold the button for a few seconds to adjust rapidly. Remember to set the correct AM or PM. An icon below the time digits is the PM Indicator. 3. Press the Clock Adj Button again (or no button within 10 seconds) to exit the clock setting mode.
Charging your iPhone/iPod
Note: Please make sure you are using the correct inset for your iPhone/iPod (see Install iPhone/iPod Insert) and that it is properly docked into the iP41. Failure to do so may damage your iPhone/iPod. While your iPhone/iPod is docked in the unit and the unit is connected to AC power, it recharges (until fully charged).

Listening to iPhone/iPod

1. Dock the already playing iPhone/iPod, the iP41 will automatically turn on and you will hear the music playing from your iPhone/iPod. Note: If the volume is too low on the iPhone/iPod, iP41 may not detect iPhone/iPod is in play mode. Press the Power Button on the main unit once or Play/Pause Button to play it. 2. When the iPhone/iPod is docked and in standby mode, press the Button on main unit to play it. The iPod icon will appear on the display indicating iPod mode 3. Press the Button to pause play; press again to resume it. 4. Press the and Button to adjust the system volume. 5. Press or Button on remote control to go to the next or previous track. Press and hold while track is playing for high speed forward or reverse music search of the current track. 6. You can rotate the unit for viewing video, the iP41 display also will change to fit your view orientation too. 7. To turn off the unit, press the Button on the main unit or remote control. Your iPhone/iPod will continue charging while in the dock.

Using the Alarm

Setting the Alarm 1. Press and hold the Alarm Button until the alarm time flashes. Press the Hour and/or Minute Button to set the alarm time. Hold the button for a few seconds to adjust rapidly. Remember to set the correct AM or PM. 2. The alarm will automatically arm after set alarm time and the alarm icon will stay on to indicate alarm is armed. 3. Default alarm sound is iPhone/iPod but if no iPhone/iPod is docked or iPhone/iPod cannot play for some reason or the playing sound level is too low, it will automatically switch to buzzer alarm. Arming and Disarming Alarm (Turn Alarm Function On and Off) 1. Once alarm is armed, press the Alarm Button to disarm it. 2. Press the button again to arm the alarm again. Resetting the Alarm to Come on the Next Day When the alarm is sounding, press the Alarm Reset/Power Button to stop the alarm and reset it to come on the following day at the same time. Snooze Press the Snooze/Dimmer Button after the alarm sounds. The alarm will be silenced and come on again about 9 minutes later. Snooze can be pressed several times during the 1 hour alarm cycle. Sure Alarm The iP41 has a sure alarm feature so if a backup battery is installed, the buzzer alarm will still sound in the event of power failure.
Listening to non-docking iPod or other portable audio devices
If you are using an iPod without a docking port or other MP3 player or other portable audio device, you can play it through the iP41 via the Aux-in Jack. 1. Plug one end of an audio patch cord (available at www.ihome.com ) into the headphone or line-out jack on your device and the other end of the patch cord into the Aux-in Jack, located on the back of the unit. 2. Press the Button to turn the iP41 on. 3. Press the or Button on the main unit or on the remote control to adjust the system volume. You may need to adjust your device volume too. 4. To turn off the unit, press the Button. Please remember to turn off your device, too.
Watching Videos (iPhone and iPod models with Horizontal Video Mode)
Make sure you have installed the correct cradle for your iPhone, iPod touch or nano 4G model. 1. Gently turn the unit with docked iPhone or iPod on its left side. The clock display will adjust to the new orientation. 2. Select a video file on your iPhone/iPod and press play. 3. Press Play on the iP41 if needed to turn unit on.

iP41 UK

size: 178 x 178 color: Black Sept 4, 2009
Model iP41 Alarm Clock for iPhone / iPod
Questions? Visit www.ihomeintl.com

iP41-110909-0 (UK) nr

2009 SDI technologies All rights reserved

iP41 UK 110909-nr

Table of Contents
Quick Start...... 1 Controls and Indicators / iP41 Display.... 2 Getting Started...... 3 Using the iP41..... 4-6 IA Consumer Guide to Product Safety.... 7 Troubleshooting..... 8

Maintenance

Place the unit on a level surface away from sources of direct sunlight or excessive heat. Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should be placed between it and the furniture. Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzine, thinner or similar materials can damage the surface of the unit.
This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European Directive 2002/96/EC in order to be recycled or dismantled to minimize its impact on the environment. For further information, please contact your local or regional authorities. Electronic products not included in the selective sorting process are potentially dangerous for the environment and human health due to the presence of hazardous substances.

Troubleshooting

Symptom Unit no respond (no power) Possible Problem AC adaptor isnt plugged to a wall outlet or the connector is not plugged into the power supply jack o the back of the unit Wall outlet is not functioning iPhone/iPod does not dock properly Using wrong insert/ no insert dock or iPhone/iPod has obstruction Solution Plug the AC adaptor into a wall outlet and plug the connector into the supply jack on the unit

iP41 Quick start

1: AC power 2: inserts & cradles

ESET R EST T

3: iPhone/iPod
Plug another device into a wall outlet (same outlet) to confirm the outlet is working Make sure the dock insert is the proper fit to your iPhone/iPod Remove your iPhone/iPod from the dock and check for obstruction on the connectors in the dock and on your iPhone/iPod. Then reseat it in the dock. Remove your iPone/iPod from the dock and check for obstruction on the connectors in the dock and on your iPhone/iPod. Then reseat it in the dock. Upgrade software on your iPhone/iPod via iTunes. Please make sure your iPhone/iPod is working properly before docking with the unit. Please refer to your iPod manual for details. Remove your iPhone/iPod from the dock and check for obstruction on the connectors in the dock and on your iPod. Then reseat it in the dock. iP41 doesnt support 3rd generation iPod Please make sure your iPhone/iPod is working properly before docking with the unit. Please refer to your iPod manual or apple.com/support for details. Decrease the volume. Turn off EXB bass effect If iPod original sound source is poor quality, distortion and noise are easily noticed with high-power speakers. Try a difference audio source such as a music CD. If you are using an iPod Shuffle or external sound source like older generation iPod, try reducing the output volume on the device itself. Also, try turning bass boost OFF.

RESET TEST

iPhone/iPod does not respond to the unit
iPhone/iPod is not docked properly
Your iPhone/iPod software is too old iPhone/iPod is locked up iPhone/iPod is not docked properly
Attach AC adaptor cable to jack on back of the iP41 and plug the other end into a wall socket to play and charge iPhone/iPod
Select the dock insert for your iPhone/iPod model from the table below and place insert in dock. Never dock an iPhone/iPod without the proper insert in place. Insert the short cradle for your iPhone or iPod touch or tall cradle for nano 4G into the slot next to the dock

Insert iPhone/iPod into dock (iPhone/iPod must not be in a skin or case). iPhone/iPod will charge while docked. Press the Play Button on the iP41 to play your iPhone/iPod.

Use this insert

For this iPhone/iPod
iPhone 3G Insert 15 iPhone 3G
iPod touch 2G insert 16 iPod Touch 2G
iPod nano 5G insert 18 iPod nano 5G insert 18
iPhone/iPod didnt charge up
Using 3rd generation iPod iPhone/iPod is locked up/frozen iPhone/iPod battery has problem Sound is distorted Volume level is set too high Sound source is distorted
4: watching horizontal screen video
Gently pivot unit to the left until it lies flat. The clock display will adjust to the new orientation. Select your video and press the Play Button on the iP41 to play your video.

iP41 UK 50609

Controls and Indicators
Hour Button Alarm Button Minute Button Alarm Reset/Power Button
A Consumer Guide to Product Safety
iPhone/iPod cradle Snooze/Dimmer Button Play/Pause Button Volume- Button Sleep Button Volume+ Button DST Switch Clock Adjust Button Expanded Bass Effect Switch Aux-in Jack

DC Jack

Back Panel

iP41 Display

Time Display Alarm Indicator Sleep Indicator Battery Low Indicator DST Indicator PM Indicator iPod/iPhone Indicator
Display in iPhone/iPod Mode (product is upright) 2
Display in Movie Mode (product is sideways)
When used in the directed manner, this unit has been designed and manufactured to assure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use. Keep these instructions handy for future reference. Take special note, and adhere to all warnings on the unit and in the instruction and service manual. 1. Water and Moisture - The unit should not be used near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. 2. Ventilation - The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, it should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or placed in a built-in installation, such as bookcase or cabinet that may impede the flow of air through the ventilation openings. 3. Heat - The unit should be situated away from heat source such as radiators, heat register, stoves, or other appliances (including amplifiers) that produce heat. 4. Power Sources - The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. 5. Power Cord Protection - Power supply cord should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. It is always best to have a clear area from where the cord exits the unit to where it is plugged into an AC outlet. 6. Cleaning - The unit should be cleaned only as recommended by the manufacturer. 7. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. 8. Attachments - Do not use attachments not recommended by the product manufacturer. 9. Lightning and Power Surge Protection - Unplug the unit from the wall outlet and disconnect the antenna or cable system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage to the product due to lightning and power-line surges. 10. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 11. Damage Requiring Service - The appliance should be serviced by qualified service personnel when: A. The power-supply cord or plug has been damaged. B. Objects have fallen into or liquid has been spilled into the enclosure. C. The unit has been exposed to rain. D. The unit has been dropped or the enclosure damaged. E. The unit exhibits a marked change in performance or does not operate normally. 12. Periods of Nonuse - If the unit is to be left unused for an extended period of time, such as a month or longer, the power cord should be unplugged and take out batteries from the unit to prevent damage or corrosion. 13. Servicing - The user should not attempt to service the unit beyond that described in the users operating instructions. All other servicing should be referred to qualified service personnel.

iP41 UK 90409

Using the iP41

Using Sleep Mode

Press the Sleep Button while your iPhone/iPod is playing to enter sleep mode and continue to press to step through the available sleep times: 90, 60, 30 and 15 (OFF will cancel sleep mode). A sleep icon will appear on the display. The iP41 will play for the number of minutes set, growing gradually softer until shutting off the unit and the iPhone/iPod at the set time. Press or Button to set sleep volume. Note that sleep volume is separate from normal/alarm volume setting.

Getting Started

Thank you for purchasing the iHome iP41 Alarm Clock for your iPhone/iPod. Designed specifically to work with your iPhone or iPod Touch, this system provides high quality audio performance and lets you enjoy videos in horizontal view. Please read this instruction carefully before the appliance is operated and keep it for future reference. Install iPhone/iPod Insert & Cradle Your iP41 comes with two cradles for support when viewing videos in horizontal mode and three inserts to ensure your iPhone/iPod fits properly in the dock. To place a cradle: 1. Select the small iPhone /iPod touch cradle for use with those models or the taller nano cradle for use with nano. 2. Press cradle into the vertical cradle slot on the unit (near the dock). To place an insert: 1. Select the insert for your iPhone/iPod. (see table on page 1) 2. Gently press the iPhone/iPod insert into the dock. 3. Carefully place your iPhone/iPod into the dock. The iPhone/iPod must not be in a case or skin. Install AC Adaptor Connect the AC adaptor cable plug into the jack on the back of the system, then plug the AC adaptor into the wall outlet. Install/Replace backup Battery The iP41 uses a CR2032 battery for backup battery system to provide continuous alarm operation and clock settings in the event of a power failure. If the Backup Battery has been installed and a power failure occurs or the AC cord is accidentally disconnected, the display backlight will not remain lit, but current time and alarm time settings will be temporarily maintained. Otherwise, you must reset the time and alarm settings. 1. Please make sure the AC adaptor is connected. Otherwise all settings may be lost during battery replacement. 2. Open backup battery compartment door located on the back of the unit. 3. Insert a new CR2032 battery, checking that the polarity (+ and ends of the battery) matches the drawing near the battery compartment. Close the compartment door. Note: Make sure you dispose of batteries properly (see your local regulations).

WARNING: Lithium batteries can explode or cause burns if disassembled, shorted, recharged, exposed to water, fire, or high temperatures. Do not place loose batteries in a pocket, purse, or other container containing metal objects, mix with used or other battery types, or store with hazardous or combustible materials. Store in cool, dry, ventilated area. Follow applicable laws and regulations for transport and disposal.

Using Dimmer

Press the Snooze/Dimmer Button during normal operation to adjust the brightness of the LCD display to high, medium, low or off.

Using the EXB effect

Slide the EXB Switch at the back of the unit to the ON position to enable the EXB sound enhancement circuitry, designed to provide bigger bass sound. Slide to OFF to cancel the effect.

iP41 UK Sept 03, 2009

Setting the Clock
1. Set the DST Switch located on the back of the unit to +1 to add one hour or to -1 to subtract an hour. When set to +1 the DST icon will appear. 2. Press and hold the Clock Adj Button located on the back of the unit until the display flashes. Press the Alarm Button at any time during clock setting to toggle the display between 24 hour (military) and 12 hour (standard) display mode. Press the Hour and/or Minute Button to set the time. Hold the button for a few seconds to adjust rapidly. Remember to set the correct AM or PM. An icon below the time digits is the PM Indicator. 3. Press the Clock Adj Button again (or no button within 10 seconds) to exit the clock setting mode.
Charging your iPhone/iPod
Note: Please make sure you are using the correct inset for your iPhone/iPod (see Install iPhone/iPod Insert) and that it is properly docked into the iP41. Failure to do so may damage your iPhone/iPod. While your iPhone/iPod is docked in the unit and the unit is connected to AC power, it recharges (until fully charged).

Listening to iPhone/iPod

1. Dock the already playing iPhone/iPod, the iP41 will automatically turn on and you will hear the music playing from your iPhone/iPod. Note: If the volume is too low on the iPhone/iPod, iP41 may not detect iPhone/iPod is in play mode. Press the Power Button on the main unit once or Play/Pause Button to play it. 2. When the iPhone/iPod is docked and in standby mode, press the Button on main unit to play it. The iPod icon will appear on the display indicating iPod mode 3. Press the Button to pause play; press again to resume it. 4. Press the and Button to adjust the system volume. 5. You can rotate the unit for viewing video, the iP41 display also will change to fit your view orientation too. 6. To turn off the unit, press the Button on the main unit. Your iPhone/iPod will continue charging while in the dock.

Using the Alarm

Setting the Alarm 1. Press and hold the Alarm Button until the alarm time flashes. Press the Hour and/or Minute Button to set the alarm time. Hold the button for a few seconds to adjust rapidly. Remember to set the correct AM or PM. 2. The alarm will automatically arm after set alarm time and the alarm icon will stay on to indicate alarm is armed. 3. Default alarm sound is iPhone/iPod but if no iPhone/iPod is docked or iPhone/iPod cannot play for some reason or the playing sound level is too low, it will automatically switch to buzzer alarm. Arming and Disarming Alarm (Turn Alarm Function On and Off) 1. Once alarm is armed, press the Alarm Button to disarm it. 2. Press the button again to arm the alarm again. Resetting the Alarm to Come on the Next Day When the alarm is sounding, press the Alarm Reset/Power Button to stop the alarm and reset it to come on the following day at the same time. Snooze Press the Snooze/Dimmer Button after the alarm sounds. The alarm will be silenced and come on again about 9 minutes later. Snooze can be pressed several times during the 1 hour alarm cycle. Sure Alarm The iP41 has a sure alarm feature so if a backup battery is installed, the buzzer alarm will still sound in the event of power failure.
Listening to non-docking iPod or other portable audio devices
If you are using an iPod without a docking port or other MP3 player or other portable audio device, you can play it through the iP41 via the Aux-in Jack. 1. Plug one end of an audio patch cord (available at www.ihome.com ) into the headphone or line-out jack on your device and the other end of the patch cord into the Aux-in Jack, located on the back of the unit. 2. Press the Button to turn the iP41 on. 3. Press the or Button on the main unit to adjust the system volume. You may need to adjust your device volume too. Button. Please remember to turn off your device, too. 4. To turn off the unit, press the
Watching Videos (iPhone and iPod models with Horizontal Video Mode)

1. Select a video file on your iPhone/iPod and press play. 2. Gently turn the unit with docked iPhone/iPod on its left side. The clock display will adjust to the new orientation. 3. Press Play on the iP41 if needed to turn unit on.