OPEN TAP

T Remove and empty the water tank. T Open the filter holder.

OK INSERT FILTER

T Insert the filter cartridge into the water tank, exerting slight pressure.
Determining and adjusting the water hardness E If you are using the CLARIS Blue filter
cartridge and have activated it in programming mode, you will not be able to adjust the water hardness. The harder the water is, the more frequently the ENA needs to be descaled. It is therefore important to adjust the water hardness.
T Close the filter holder. It will click into place audibly.
E After two months, the filter will cease to
work. You can check the elapsed time by referring to the date plate on the filter holder in the water tank. T Fill the water tank with fresh, cold water and reinsert it. T Place a receptacle (at least 500 ml) under the cappuccino frother. k T Press the Rotary Switch. l T Turn the switch anticlockwise to position m. FILTER RINSING, water flows out of the cappuccino frother.
The water hardness can be adjusted on a continuous scale between 1 dH and 30 dH. It can also be deactivated, which means that the ENA will not let you know when it has to be descaled. Determining the water hardness You can find out what the water hardness is by using the Aquadur test strip supplied as standard. T Hold the test strip briefly (for one second) under running water. T Shake off the water. T Wait for about one minute. T You will then be able to read the degree of water hardness from the discolouration of the Aquadur test strip and the description on the packaging. The water hardness can now be adjusted. Adjusting the water hardness Example: Change the water hardness setting from 16 dH to 25 dH. Precondition: READY is displayed. k T Press and hold the Rotary Switch until RINSE appears. g T Turn the Rotary Switch until HARDNESS is displayed. k T Press the Rotary Switch to enter the programme item.
E You can interrupt rinsing of the filter at any
time. To do this, turn the switch clockwise. Turn the switch anticlockwise to continue rinsing the filter. E The water may be slightly discoloured. This is not harmful to health and does not affect the taste. Rinsing of the filter stops automatically, y T Turn the switch clockwise to position o.

CLOSE TAP. HEATING READY

The filter is now activated.
g T Turn the Rotary Switch until 25 dH is displayed.
k T Press the Rotary Switch to confirm the setting. OK, the water hardness is set.

2 Preparation

E You can stop the machine at any time while
a coffee speciality or steam for cappuccino is being prepared. Just press any button. E Before and during the grinding operation you can select the coffee strength of 1 espresso and 1 coffee: MILD, NORMAL, STRONG. E During preparation, you can change the preset amount of water by turning the Rotary Switch. E You can follow the current status of preparation on the progress bar. You can make permanent settings for all products in programming mode (see Chapter 4 Permanent settings in programming mode Products).

HARDNESS

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.
READY Adjusting the grinder
You can adjust the grinder on a continuous scale to suit the degree of roast of your coffee. CAUTION If you adjust the consistency of grind when the grinder is not operating, the grinding wheel could be damaged. T Only adjust the consistency of grind when the grinder is running. The consistency of grind setting is correct if the coffee flows regularly from the coffee spout. In addition a fine, thick crema forms. Example: Change the consistency of grind during the preparation of an espresso. T Place a cup under the coffee spout. < T Press the Espresso button to start preparation. T Turn the grinding wheel to the desired position while the grinder is running.

Espresso and coffee

The preparation of 1 espresso and 1 coffee always follows this model. Example: Prepare one coffee. Precondition: READY is displayed. T Turn the coffee spout to the 1 cup position.
T Place a cup under the coffee spout. > T Press the Coffee button to start preparation. 1 COFFEE, the preset amount of water flows into the cup. Preparation stops automatically.
1 ESPRESSO, the preset amount of
water flows into the cup and preparation stops automatically.

READY 10

Preparing two speciality coffees at the touch of a button
The preparation of 2 espressi and 2 coffees follows this same model. Example: Prepare two espressi. Precondition: READY is displayed. T Turn the coffee spout to the 2 cups position.
T Place a cup under the coffee spout. = T Press the Aroma Boost button to start preparation. SPECIAL, the preset amount of water flows into the cup. Preparation stops automatically.

READY Preground coffee

You can choose a second coffee variety, for example decaffeinated coffee, with the powder chute for preground coffee.
E Never add more than two level measuring
spoons of preground coffee.
E Use preground coffee which is not ground
T Place two espresso cups under the coffee spout. < T Press the Espresso button twice (within two seconds) to start coffee preparation. 2 ESPRESSI, the preset amount of water flows into the cups. Preparation stops automatically. too finely. Very fine coffee can block up the system so that the coffee only comes out in drips. E If you did not fill the machine with a sufficient amount of preground coffee, NOT ENOUGH POWDER is displayed and the ENA stops the operation. E The desired speciality coffee must be prepared within approximately one minute after filling with the preground coffee. Otherwise the ENA stops the operation and is once more ready for use. All speciality coffees with preground coffee are prepared following this model. Example: Prepare a cup of coffee using preground coffee. Precondition: READY is displayed, the coffee spout is set to the 1 cup position. T Place a cup under the coffee spout. T Open the powder chute.

READY Aroma Boost

When you prepare an Aroma Boost the maximum possible amount of powder is freshly ground and extracted to make an extra strong espresso or coffee. Precondition: READY is displayed. T Turn the coffee spout to the 1 cup position.

FILL POWDER

T Place the filler funnel for preground coffee on to the powder chute.
T Place one level measuring spoon of preground coffee into the filler funnel. T Remove the filler funnel. T Close the powder chute. > T Press the Coffee button to start preparation. 1 COFFEE, the preset amount of water flows into the cup. Preparation stops automatically.
Precondition: READY is displayed, the coffee spout is set to the 1 cup position. T Place a cup under the coffee spout. > T Press and hold the Coffee button. 1 COFFEE, the grinding operation starts. > T Continue to hold the Coffee button down until ENOUGH COFFEE? appears. > T Release the Coffee button. The coffee flows into the cup. T Press any button as soon as there is sufficient coffee in the cup. OK, 1 COFFEE, the set amount of water for one coffee is permanently stored.

READY E You can alter this setting at any time by
repeating the above procedure.

SELECT BUTTON

Cappuccino
For a cappuccino you must first froth the milk using the cappuccino frother. You then prepare an espresso straight into the milk foam.
READY E It is also possible to prepare two cups of
preground coffee. To do this, place two cups under the coffee spout and add two level measuring spoons of preground coffee into the filler funnel. Press the Coffee button > twice (within two seconds) to start preparation.
E This chapter applies to the Professional and
Easy Cappuccino Frothers. Precondition: READY is displayed, the coffee spout is set to the 1 cup position. T Take the protective cover off the cappuccino frother. T Attach the milk pipe to the cappuccino frother. T Insert the other end of the milk pipe into a milk carton or connect it to a milk container. T Place a cup under the cappuccino frother.
Permanently setting the amount of water for the cup size
It is easy to permanently set the amount of water for all speciality coffees, milk specialities and hot water to the cup size. Adjust the amount once as shown in the following example. Every time you prepare a drink in the future, this amount of water will be dispensed. Permanent setting of the amount of water to the cup size for all speciality coffees, milk specialities and hot water follows this model. Example: Permanently adjust the amount of water to the cup size.
E If you are using the Professional Cappuccino Frother, set the selector switch to the Milk Foam position p. n T Press the Steam button.
T Place a cup under the cappuccino frother.

HEATING

As soon as the ENA has heated up, READY appears again. l T Turn the switch anticlockwise to position m. STEAM, the milk foam is prepared. y T Turn the switch clockwise to position o when there is sufficient milk foam in the cup.
en E If you are using the Professional Cappuccino Frother, set the selector switch to the Milk Foam position p. E If you want to heat the milk, turn the selector switch of the frother to the Milk position t. n T Press the Steam button.
E You can continue to prepare steam for the
next 40 seconds or so without the machine having to heat up again. T Place a cup under the coffee spout. < T Press the Espresso button to start preparation. 1 ESPRESSO, the preset amount of water flows into the cup. Preparation stops automatically. To make sure the cappuccino frother always works properly, it should be rinsed and cleaned regularly (see Chapter 5 Maintenance Rinsing the cappuccino frother).
As soon as the machine has heated up, READY appears. l T Turn the switch anticlockwise to position m. STEAM, the milk foam is prepared. y T Turn the switch clockwise to position o when there is sufficient milk foam in the cup.

next 40 seconds or so without the machine having to heat up again. To make sure the cappuccino frother always works properly, rinse and clean it regularly (see Chapter 5 Maintenance Rinsing the cappuccino frother).
Hot milk and milk foam E This chapter applies to the Professional and
Easy Cappuccino Frothers. Example: Proceed as follows to prepare milk foam. Precondition: READY is displayed. T Take the protective cover off the cappuccino frother. T Attach the milk pipe to the cappuccino frother. T Insert the other end of the milk pipe into a milk carton or connect it to a milk container.
Cappuccino with the 2-stage frothing nozzle
Precondition: READY is displayed, the coffee spout is set to the 1 cup position. T Push the 2-stage frothing nozzle to the lower position.
T Place a cup of milk below the 2-stage frothing nozzle and immerse the nozzle in the milk.
Hot milk with the 2-stage frothing nozzle
Precondition: READY is displayed. T Push the 2-stage frothing nozzle to the upper position. T Place a cup of milk below the 2-stage frothing nozzle and immerse the nozzle in the milk.
E If the nozzle does not reach into the cup, lift
the cup. n T Press the Steam button.
As soon as the ENA has heated up, READY appears again. l T Turn the switch anticlockwise to position m. STEAM, the milk is frothed by the hot steam. y T Turn the switch clockwise to position o when the milk foam has reached the required consistency.
the cup. T Prepare steam (see Chapter 2 Preparation Cappuccino with the 2-stage frothing nozzle).
Hot water E To prepare hot water, either attach the
hot-water nozzle or the 2-stage frothing nozzle to the Connector System.
next 40 seconds or so without the machine having to heat up again. T Place a cup under the coffee spout. < T Press the Espresso button to start preparation. 1 ESPRESSO, the preset amount of water flows into the cup. Preparation stops automatically. To make sure the 2-stage frothing nozzle always works properly, it should be rinsed regularly (see Chapter 5 Maintenance Dismantle and rinse the 2-stage frothing nozzle).

J CAUTION

There is a danger of scalding from hot water splashes. T Avoid direct contact with the skin. Precondition: READY is displayed. T Place a cup under the hot-water spout. l T Turn the switch anticlockwise to position m. WATER, hot water flows into the cup. y T Turn the switch clockwise when there is sufficient water in the cup.

ENERGY - to ENERGY p. Precondition: READY is displayed.

OFF AFTER

g T Turn the Rotary Switch until LANGUAGE is displayed. k T Press the Rotary Switch to enter the programme item.
READY Unit for amount of water
You can change the unit for the amount of water from ml to oz. Example: Change the unit for the amount of water from ML to OZ. Precondition: READY is displayed. k T Press and hold the Rotary Switch until RINSE appears. g T Turn the Rotary Switch until DISPLAY is displayed. k T Press the Rotary Switch to enter the programme item.

ENGLISH

g T Turn the Rotary Switch until DEUTSCH is displayed. k T Press the Rotary Switch to confirm the setting. OK, the language is set.

SPRACHE

BEREIT

Maintenance

g T Turn the Rotary Switch until OZ is displayed. k T Press the Rotary Switch to confirm the setting. OK, the unit for the amount of water is set.

DISPLAY

Your ENA has the following integrated maintenance programmes: Rinsing the machine Cleaning the machine Changing the filter Descaling the machine
E Clean or descale the machine or change the
filter when the display prompts you to do so.

READY Language

In this programme item you can set the language used by your ENA. Example: Change the language from ENGLISH to DEUTSCH. Precondition: READY is displayed. k T Press and hold the Rotary Switch until RINSE appears.

Rinsing the machine

You can initiate the rinse operation manually at any time. Precondition: READY is displayed. T Place a receptacle under the coffee spout. k T Press and hold the Rotary Switch until RINSE appears. k T Press the Rotary Switch to enter the programme item.
k T Press the Rotary Switch to initiate the rinse operation. RINSING, the system rinses itself, stopping automatically.
READY Cleaning the machine
After 180 preparations or 80 switch-on rinses, the ENA will prompt you to clean it. CAUTION If the wrong cleaning agent is used, the machine could be damaged and/or traces could be left behind in the water. T Use only original JURA maintenance products.
T Place a receptacle under the coffee spout. k T Press the Rotary Switch to start cleaning. CLEANING, water flows out of the coffee spout. The operation is interrupted, ADD TABLET. T Open the powder chute for preground coffee and drop in a JURA cleaning tablet.
E The cleaning programme lasts approximately 15 minutes. E Do not interrupt the cleaning programme. The quality of cleaning will be impaired if you do so. E JURA cleaning tablets are available from stockists. Precondition: CLEAN / READY is displayed. T Open the cover behind the Rotary Switch. c T Press the Maintenance button. T Empty the drip tray and coffee grounds container and reinsert them. T Turn the coffee spout to the Cleaning position.

T Close the powder chute for preground coffee. k T Press the Rotary Switch. CLEANING, water flows out of the coffee spout several times. T Empty the drip tray and coffee grounds container and reinsert them. T Turn the coffee spout to the 1 cup or 2 cups position.

PRESS ROTARY

EMPTY TRAY
Changing the filter E After 50 litres of water have flowed through,
the filter will cease to work. Your ENA will automatically prompt you to change the filter. E After two months, the filter will cease to work. You can check the elapsed time by referring to the date plate on the filter holder in the water tank. E If the CLARIS Blue filter cartridge is not activated in programming mode, you will not be prompted to change the filter.
Precondition: FILTER / READY is displayed. T Open the cover behind the Rotary Switch. c T Press the Maintenance button. T Remove and empty the water tank. T Open the filter holder and remove the old filter cartridge. T Insert a new filter cartridge into the water tank, exerting slight pressure.

Descaling the machine

The ENA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the hardness of your water.

INSERT FILTER

If the descaling agent comes into contact with the skin or eyes, this can cause irritation. T Avoid contact with the skin or eyes. T Rinse off descaling agent with clean water. Should you get any descaling agent in your eye, seek medical attention. CAUTION If the wrong descaling agent is used, the machine could be damaged and/or traces could be left behind in the water. T Use only original JURA maintenance products. CAUTION If the descaling operation is interrupted, there may be damage to the machine. T Allow the descaling programme to run to the end. CAUTION If the descaling agent comes into contact with sensitive surfaces (e.g. marble), damage cannot be ruled out. T Clean up any splashes immediately.
T Close the filter holder. It will click into place audibly. T Fill the water tank with fresh, cold water and reinsert it. T Place a receptacle (at least 500 ml) under the cappuccino frother. k T Press the Rotary Switch. l T Turn the switch anticlockwise to position m. FILTER RINSING, water flows out of the cappuccino frother.
time. To do this, turn the switch clockwise. Turn the switch anticlockwise to continue rinsing the filter. E The water may be slightly discoloured. This is not harmful to health and does not affect the taste. Rinsing of the filter stops automatically, CLOSE TAP. y T Turn the switch clockwise to position o.
E The descaling programme lasts approximately 40 minutes.
E JURA descaling tablets are available from

stockists.

E If you use a CLARIS Blue filter cartridge and
this is activated, you will not be prompted to descale.

HEATING READY

Precondition: DE-SCALE / READY is displayed. T Open the cover behind the Rotary Switch. c T Press the Maintenance button. T Empty the drip tray and coffee grounds container and reinsert them. T Remove and empty the water tank. T Completely dissolve the contents of one blister (three JURA descaling tablets) in a receptacle holding 500 ml of water. This may take several minutes.
T Remove the water tank, rinse thoroughly, fill with fresh, cold water and reinsert. l T Turn the switch anticlockwise to position m. DE-SCALING, water flows out of the Connector System. The operation is interrupted, CLOSE TAP. y T Turn the switch clockwise to position o. DE-SCALING, the descaling operation is continued. T Empty the drip tray and coffee grounds container and reinsert them. T Reattach the cappuccino frother to the Connector System.

AGENT IN TANK

E If the descaling operation stops unexpectedly, rinse the water tank thoroughly.
T Pour the solution into the empty water tank and reinsert the tank. T Carefully pull the cappuccino frother off the Connector System. T Place a receptacle (at least 500 ml) under the Connector System. l T Turn the switch anticlockwise to position m. DE-SCALING, water flows out of the Connector System several times. y T Turn the switch clockwise to position o. DE-SCALING, the descaling operation is continued. T Empty the drip tray and coffee grounds container and reinsert them. T Empty the receptacle and place it back under the Connector System.
Rinsing the cappuccino frother E This chapter applies to the Professional and
Easy Cappuccino Frothers. To ensure that the cappuccino frother always works properly, you should rinse it with water after every milk preparation. Your ENA will not prompt you to rinse the cappuccino frother. T Remove the milk pipe from the milk carton or the milk container. T Fill a receptacle with fresh water and immerse the milk pipe in the water. T Place another receptacle under the cappuccino frother.

CLOSE TAP

FILL WATER TANK
E If you are using the Professional Cappuccino Frother, turn the selector switch to the Milk Foam p or Milk t position. n T Press the Steam button.

T Allow the frothing nozzle to cool before cleaning it. T Carefully pull the frothing nozzle off the Connector System. T Unscrew the frothing nozzle using the hole on the measuring spoon for preground coffee.
Dismantling and rinsing the Easy Cappuccino Frother
T Carefully remove the Easy Cappuccino Frother from the Connector System by twisting slightly. T Dismantle the cappuccino frother into its individual parts.
T Rinse all three nozzle parts thoroughly under running water. T Reassemble the frothing nozzle and attach it to the Connector System.
Cleaning the bean container
Coffee beans may be covered with a slight oil film which remains on the walls of the bean container. These traces may negatively affect the coffee result. For this reason clean the bean container from time to time. Q T Press the On/Off button to switch the machine off. T Disconnect the mains plug. T Remove the bean container cover. T Remove the coffee beans with a vacuum cleaner. T Clean the bean container with a soft, dry cloth. T Fill the bean container with fresh coffee beans, then close the bean container cover.

Descaling the water tank

Limescale deposits may form in the water tank. To ensure correct function of the machine, descale the water tank from time to time. T Remove the water tank. T If you use a CLARIS Blue filter cartridge, remove it. T Descale the tank with a mild conventional descaling agent in accordance with the manufacturer's instructions. T Rinse the water tank thoroughly. T If you use a CLARIS Blue filter cartridge, reinsert it. T Fill the water tank with fresh, cold water and reinsert it.

6 Display messages

Message Cause/Result
The water tank is empty. You cannot prepare any products. The coffee grounds container is full. You cannot prepare any speciality coffees or steam, but you can prepare hot water. The drip tray is not inserted correctly or is not inserted at all. You cannot prepare any speciality coffees, but you can prepare hot water and steam. The bean container is empty. You cannot prepare any speciality coffees, but you can prepare hot water and steam. The ENA is prompting you to clean it. descale it.

Action

T Fill the water tank (see Chapter 1 Preparing and using for the first time). T Empty the coffee grounds container and the drip tray (see Chapter 3 Daily operation). T Insert the drip tray.

FILL WATER TANK EMPTY GROUNDS

TRAY MISSING

FILL BEANS
T Fill the bean container (see Chapter 1 Preparing and using for the first time).

READY / CLEAN

T Perform cleaning (see Chapter 5 Maintenance Cleaning the machine). T Perform descaling (see Chapter 5 Maintenance Descaling the machine). T Replace the CLARIS Blue filter cartridge (see Chapter 5 Maintenance Changing the filter). T The next time you prepare a beverage, add more preground coffee (see Chapter 2 Preparation Preground coffee). T Wait for several minutes until the system has cooled or prepare a speciality coffee or hot water. T Place a receptacle under the cappuccino frother and turn the switch anticlockwise to position m.
READY / DE-SCALE The ENA is prompting you to READY / FILTER
After 50 litres of water have flowed through the CLARIS Blue filter cartridge, it will cease to work. There is insufficient preground coffee in the machine; the ENA stops the operation. The system is too hot to start a maintenance programme. The system must be filled with water. You cannot prepare any products.

NOT ENOUGH POWDER

TOO HOT

Troubleshooting

Cause/Result
The cappuccino frother is dirty.

Problem

Insufficient foam is produced when the milk is frothed or milk sprays from the cappuccino frother. Coffee only comes out in drips when it is being prepared. Water hardness cannot be adjusted.
T Clean the cappuccino frother (see Chapter 5 Maintenance Cleaning the cappuccino frother).
Coffee or preground coffee has been ground too finely and is blocking the system. The CLARIS Blue filter cartridge is activated. The water tank float is trapped. There are foreign objects in the grinder. The connector of the cappuccino frother may be blocked by milk residues or limescale fragments loosened during descaling.
T Set the grinder to a coarser setting or use coarser preground coffee (see Chapter 1 Preparing and using for the first time Adjusting the grinder). T Deactivate the CLARIS Blue filter cartridge in programming mode. T Descale the water tank.
is displayed although the water tank is full. Grinder is making a very loud noise. Little or no water or steam comes out of the cappuccino frother. The pump is very quiet.
T Contact customer support in your country (see Chapter 11 JURA contact details / Legal information). T Remove the cappuccino frother. T Unscrew the black connector with the aid of the hexagonal hole on the measuring spoon for preground coffee. T Thoroughly clean the connector. T Screw the connector back on by hand and carefully tighten it using the hexagonal hole on the measuring spoon, turning by no more than a quarter of a rotation. T Warm the machine at room temperature.

ERROR 2 is displayed.

If the machine was exposed to the cold for a long period of time, heating is disabled for safety reasons.
Other ERROR messages are displayed.
T Switch off the ENA with the On/Off button. Contact customer support in your country (see Chapter 11 JURA contact details / Legal information).
E If you were unable to solve the problem, contact customer support in your country (see Chapter 11
JURA contact details / Legal information).
Transport and environmentally friendly disposal

9 Technical data

Voltage 220240 V ~, 50 Hz 1450 W S Approx. 13.5 Wh Approx. 4 Wh Static, max. 15 bar 1.1 l 125 g Approx. 10 servings
Transport / Emptying the system
Keep the packaging for your ENA. It should be used to protect the machine during transport. In order to protect the ENA from frost during transport, the system must be emptied. Precondition: READY is displayed. n T Press the Steam button.
Power Safety test Energy consumption
ECONOMY Energy consumption

ECONOMY p

Pump pressure Holding capacity of water tank Holding capacity of bean container Holding capacity of coffee grounds container Cable length Weight Dimensions (W H D)
As soon as the ENA has heated up, READY appears again. l T Turn the switch anticlockwise to position m. STEAM, hot steam is discharged from the cappuccino frother. T Remove and empty the water tank. Steam will continue to be discharged until the system is empty.
Approx. 1.1 m Approx. 9.3 kg 23.44.5 cm
Q T Press the On/Off button to switch the machine off. y T Turn the switch clockwise to position o.
CLOSE TAP FILL WATER TANK
E The next time you use the machine the
system must be refilled (see Chapter 1 Preparing and using for the first time First-time use).

Disposal

Please dispose of old machines in an environmentally friendly way. H Old machines contain valuable, recyclable materials which should be recycled. Please therefore dispose of old machines via suitable collection systems.

Index D

Degree of water hardness 9 Descaling Machine 19 Water tank 23 Determining and adjusting the water hardness 9 Display 5, 7 Display messages 24 Drip tray 4

Addresses 29 Aroma Boost 11 Automatic switch-off 16
Bean container 4 Cleaning 23 Filling 7 Bus bar Technical data 26 Button Aroma Boost 5 Coffee button 5 Espresso button 5 Maintenance button 5 On/Off button 5 Steam button 5
Easy Cappuccino Frother 4 Easy Cappuccino Frother Dismantling and rinsing 22 Emptying the system 26 Energy-saving mode 16 Errors Troubleshooting 25 Espresso 10
Cappuccino 12 With the 2-stage frothing nozzle 13 Cappuccino frother Cleaning 21 Easy Cappuccino Frother 4 Rinsing 20 CLARIS Blue filter cartridge Changing 18 Inserting and activating the filter 8 Cleaning Bean container 23 Cappuccino frother 21 Machine 18 Coffee 10 Coffee grounds container 4 Coffee spout Rotating coffee spout 4 Connector System 4 Consistency of grind Adjusting the grinder 10 Grinding wheel 5 Contact details 29 Cover 5 Cup grille 4 Customer support 29
Filling Bean container 7 Water tank 7 Filter Changing 18 Inserting and activating the filter 8 First-time use 8 Frother Easy Cappuccino Frother 4
Hotline 29 Hot milk 13 Hot water 14 Hot water and steam preparation Switch for hot water and steam preparation 4

Internet 7

JURA Contact details 29 Internet 7

Language 17

Machine Cleaning 18 Descaling 19 Rinsing 17 Setting up 7 Switching off 15 Switching on 15 Maintenance Daily maintenance 15 Maintenance 17 Messages, display 24 Milk Hot 13 Milk foam 13
Safety 6 Safety information 6 Settings Permanent settings in programming mode 15 Setting up Setting up the machine 7 Switch for hot water and steam preparation 4 Switching off 15 Switching on 15 Switch-off Automatic switch-off 16 Symbol description 3
Technical data 26 Telephone 29 Troubleshooting 25
Permanently setting the water for the cup size 12 Permanent settings in programming mode 15 Powder chute 4 Powder chute for preground coffee 4 Preground coffee 11 Preparation 10 Aroma Boost 11 Cappuccino 12 Coffee 10 Espresso 10 Milk 13 Preground coffee 11 Problems Troubleshooting 25 Professional Cappuccino Frother Dismantling and rinsing 22 Programming mode 15 Automatic switch-off 16 Energy-saving mode 16 Language 17 Products 15 Unit for amount of water 17 Proper use 6
Unit for amount of water 17 Use, First-time 8
Water tank Descaling 23 Filling 7 Website 7

Rinsing Cappuccino frother 20 Machine 17 Rotary Switch 5
Art. 69081/ENA 7/en/200909
11 JURA contact details / Legal information
JURA Elektroapparate AG Kaffeeweltstrasse 10 CH-4626 Niederbuchsiten Tel. +233
@ You will find additional contact details for
your country at www.jura.com.

Directives

The machine complies with the following directives: 2006/95/EC Low Voltage Directive 2004/108/EC Electromagnetic Compatibility 2005/32/EC Ecodesign

Technical changes

We reserve the right to make technical changes. The illustrations in these instructions for use show the ENA 7 Ristretto Black model. Some details of your ENA may vary.

Feedback

Your opinion is important to us! Use the contact link at www.jura.com.

Copyright

The instructions for use contain information which is protected by copyright. It is not permitted to photocopy these instructions for use or translate them into another language without the prior written consent of JURA Elektroapparate AG.

Compare the products

ENA 3 JURA standards for all automatic coffee machines Variable brewing unit, from 5 g to 16 g Intelligent Pre-Brew Aroma System (I.P.B.A.S.) Additional preground coffee powder Hot water function Cappuccino frother Height-adjustable coffee spout Multi-level conical grinder CLARIS filter cartridge High-performance pump, 15 bar Thermoblock heating system Integrated rinsing, cleaning and descaling programme Adjustable water hardness Zero-Energy Switch or power switch Swiss made

Specific advantages

Energy Save Mode (E.S.M.) Latte macchiato at the touch of a button Cappuccino at the touch of a button Aroma Boost function TFT colour display Powder recognition for additional ground coffee variety Intelligent preheating Sensitive-Touchscreen Technology TV certificate for manual Programmable amount of water Amount of water can be adjusted for each preparation Programmable coffee strength levels Coffee strength can be adjusted for each preparation Programmable brewing temperature levels Hot water temperature can be programmed to 3 levels Clear text / graphic display Clear text display Symbol display Rotary Switch Programmable switch-off time Switch-on and switch-off times for each day Active bean monitoring Monitored drip tray Integrated cappuccino rinsing and cleaning programme 3 3
Maintenance status display Alu Frame Design 3 mm aluminium front panel Height-adjustable coffee spout Width-adjustable coffee spout Height-adjustable cappuccino spout Cup illumination Connector System Sound design Stainless steel vacuum milk container Cup warmer Z Cup warmer Cool Control Professional Cappuccino Frother Water tank capacity Coffee grounds container (servings) Bean container with aroma preservation cover Voltage Power Energy consumption Energy consumption with E.S.M. 1 Energy consumption with E.S.M. 2 Energy consumption with E.S.M. Stand-by power Weight Dimensions (W x H x T) optional optional optional 1,1 l ~ g 230 V AC, 50 Hz{br}UL: 120 V AC, 60 Hz 1450 W 13.5 Wh 8 Wh 8 Wh 0W 9,3 kg 23,8 x 36 x 44,5 cm optional optional optional 1,1 l ~ g 230 V AC, 50 Hz{br}UL: 120 V AC, 60 Hz 1450 W 13.5 Wh 8 Wh 8 Wh 0W 9,3 kg 23,8 x 36 x 44,5 cm 4 Wh 0W 9,3 kg 23,8 x 36 x 44,5 cm optional optional optional 1,1 l ~ g 230 V AC, 50 Hz{br}UL: 120 V AC, 60 Hz 1450 W 13.5 Wh 65 - 111 mm 65 - 111 mm 65 - 111 mm